501-11-1
Glass, Window Frame and Mechanism
501-11-1
Section 501-11 Glass, Window Frame and Mechanism
Applicable Vehicle Type: Landwind X5
Table of Contents
Page
Specification
Material Specification .................................................................................................................... 501-11-3
Description and Operation
Glass, Window Frame and Mechanism ........................................................................................ 501-11-4
System Overview ...................................................................................................................... 501-11-4
Fixed Glass ............................................................................................................................... 501-11-4
Door Window Glass................................................................................................................... 501-11-4
Front Windshield Glass Device ................................................................................................. 501-11-5
Left Front Door Glass Device .................................................................................................... 501-11-6
Left Rear Door Glass Device..................................................................................................... 501-11-7
Side Rear Triangle Window Device........................................................................................... 501-11-8
Tail Gate Glass Device .............................................................................................................. 501-11-9
Component Terminal View ...................................................................................................... 501-11-10
Diagnosis and Testing
Glass, Window Frame and Mechanism ...................................................................................... 501-11-14
Check and Confirmation.......................................................................................................... 501-11-14
Table of Visual Inspection........................................................................................................ 501-11-14
Table of Symptoms.................................................................................................................. 501-11-15
Precision Test .......................................................................................................................... 501-11-17
Disassembly and Assembly
Left Front Door Switch Panel ...................................................................................................... 501-11-27
Left Front Door Glass.................................................................................................................. 501-11-30
Left Front Door Rear Mobile Guide Rail Assembly ..................................................................... 501-11-32
Left Front Door Window Regulator ............................................................................................. 501-11-34
Left Rear Door Switch Panel....................................................................................................... 501-11-35
Left Rear Door Mobile Guide Rail ............................................................................................... 501-11-27
Left Rear Door Triangle Window Glass....................................................................................... 501-11-39
Left Rear Door Glass .................................................................................................................. 501-11-40
Left Rear Door Window Regulator .............................................................................................. 501-11-31
Front Windshield Glass............................................................................................................... 501-11-44
Side Rear Triangle Window Assembly........................................................................................ 501-11-37
Tail Gate Glass............................................................................................................................ 501-11-54
Landwind X5
501-11-2
Landwind X5
Glass, Window Frame and Mechanism
501-11-2
501-11-3
Glass, Window Frame and Mechanism
501-11-3
Specification
Material Specification
Item
Specification
Glass glue
PU310
Glass washing solution
CL111
Primer coating
PR220
Landwind X5
501-11-4
Glass, Window Frame and Mechanism
Description and Operation
Glass, Window Frame and Mechanism
System Overview
Fixed Glass
The whole vehicle fixed glass consists of front
and rear windscreen and rear triangle window
glass. The whole vehicle fixed glass and body in
white, body closure member and other door
window glass and so on jointly form the closed
driving space, with transmitted ray function, and
provide the driver with sound visual feeling.
The fixed glass is sticked to the window frame on
the body with glue. The solidified glue has a
certain hardness and elasticity as well as seal
waterproof function.
To replace the window glass, firstly take down the
original glass, clear the residual glue on the
window frame, replace and re-bond new glass.
Door Window Glass
Door window glass is tempered glass, as all
tempered glasses, it has high strength and impact
resistance. In case of brekage under the
destructive impact, the glass fragment is not in
blade shape and the fragment particle size is
small.
Landwind X5
501-11-4
501-11-5
Glass, Window Frame and Mechanism
501-11-5
Front Windshield Glass Device
2
1
3
E31501110001
Item
Description
1
Front windshield glass
2
Front windshield galss sealing strip
3
Front windshield glass stock guide
Landwind X5
501-11-6
Glass, Window Frame and Mechanism
501-11-6
Left Front Door Glass Device
1
2
3
4
E31501110002
Item
Description
1
Left front door glass mud groove
2
Left front door glass assembly
3
Left front door window regulator
assembly
4
Left front door rear mobile guide rail
assembly
Landwind X5
501-11-7
Glass, Window Frame and Mechanism
501-11-7
Left Rear Door Glass Device
1
5
2
3
4
E31501110003
Item
Description
1
Left rear door glass mud groove
2
Left rear door glass assembly
3
Left rear door window regulator
assembly
4
Left rear door mobile guide rail
assembly
5
Left rear door triangle window glass
assembly
Landwind X5
501-11-8
Glass, Window Frame and Mechanism
501-11-8
Side Rear Triangle Window Device
1
2
3
E31501110004
Item
Description
1
Left side rear triangle window glass
sealing strip
2
Left side rear triangle window lower
wisp
3
Left side rear triangle window glass
Landwind X5
501-11-9
Glass, Window Frame and Mechanism
501-11-9
Tail Gate Glass Device
2
1
3
E31501110005
Item
Description
1
Tail gate glass
2
Tail gate glass stud
3
Tail gate glass side stock guide
Landwind X5
501-11-10
Glass, Window Frame and Mechanism
501-11-10
Component Terminal View
Left Front Door Window Regulator Motor
Right Front Door Window Regulator Motor
1
1
2
2
E31501110006
Terminal
No.
E31501110008
Function
1
Motor descending control (+)
Terminal
No.
2
Motor ascending control (+)
1
Motor descending control (+)
2
Motor ascending control (+)
Left Rear Door Window Regulator Motor
Function
Right Rear Door Window Regulator Motor
1
1
2
2
E31501110007
Terminal
No.
E31501110009
Function
1
Motor ascending control (+)
Terminal
No.
2
Motor descending control (+)
1
Motor ascending control (+)
2
Motor descending control (+)
Landwind X5
Function
501-11-11
Glass, Window Frame and Mechanism
501-11-11
Landwind X5
501-11-12
Glass, Window Frame and Mechanism
501-11-12
Left Front Power Window Switch
1
8
9
16
Right Front Door Power Window Switch
E31501110010
Terminal
No.
Function
1
Central locking locking signal
2
Central locking unlocking signal
3
Right rear door window descending
signal
4
Left rear door window descending
signal
5
Right front door window descending
signal
6
Left front door window descending
signal
7
Left front door window ascending
signal
8
Right front door window ascending
signal
9
Unused
10
Unused
11
Power window switch grounding
12
Power window switch panel lighting
power
13
Central locking switch panel lighting
power
14
Door window ban signal
15
Left rear door window ascending
signal
16
Right rear door window ascending
signal
Landwind X5
10
6
5
1
E31501110011
Terminal
No.
Function
1
Power window switch panel lighting
power
2
Unused
3
Grounding
4
Unused
5
Unused
6
Right front door window switch
descending signal
7
Right front door window ascending
signal
8
Unused
9
Door window ban signal
10
Unused
501-11-13
Glass, Window Frame and Mechanism
501-11-13
Left Rear Door Power Window Switch
Right Rear Power Window Switch
10
6
5
1
E31501110012
Terminal
No.
Function
1
Power window switch panel lighting
power
2
Unused
3
Grounding
4
Unused
5
Unused
6
Left rear doow window switch
descending signal
7
Left rear door window switch
ascending signal
8
Unused
9
Door window ban signal
10
Unused
10
6
5
1
E31501110013
Terminal
No.
Function
1
Power window switch panel lighting
power
2
Unused
3
Grounding
4
Unused
5
Unused
6
Right rear door window switch
descending signal
7
Right rear door window switch
ascending signal
8
Unused
9
Door window ban signal
10
Unused
Landwind X5
501-11-14
Glass, Window Frame and Mechanism
Diagnosis and Testing
Glass, Window Frame and Mechanism
Check and Confirmation
1.Confirm the problems proposed by the
customer and perform corresponding
inspection.
2. Observe whether there is obvious mechanical
or electrical damage.
3.Firslty solve the problem discovered before
proceeding to the next inspection.
4.If it’s unable to confirm reason from the
appearance, firstly confirm the symptom and
check it as per the Table of Symptoms.
Table of Visual Inspection
Mechanical
·Widow seal is untight
·Window frame is
deformed
·Door damage
Landwind X5
Electrical
·Fuse blown
·Short circuit
·Open circuit
·Window regulator
switch damage
·Window regulator
motor damage
·BCM damage
501-11-14
501-11-15
Glass, Window Frame and Mechanism
501-11-15
Table of Symptoms
Symptom
Possible Cause
Measure
All power windows
don’t work
·Fuse blown
·Replace fuse
·BCM damage
·Replace BCM
Left front door power
window doesn’t work
·Left front power window control switch ·Replace the power window switch
damage
·Left front power window motor
damage
·Go to Precision Test A
·Short circuit
·Open circuit
Right front door
·Right front power window control
·Replace the power window switch
power window doesn’t switch damage
work
·Left front power window control switch ·Replace the power window switch
damage
·Right front power window motor
damage
·Go to Precision Test B
·Short circuit
·Open circuit
Left rear door power
window doesn’t work
·Left rear power window control switch ·Replace the power window switch
damage
·Left front power window control switch ·Replace the power window switch
damage
·Left rear power window motor damage ·Go to Precision Test C
·Short circuit
·Open circuit
Right rear power
window doesn’t work
·Right rear power window control
switch damage
·Replace the power window switch
·Left front power window control switch ·Replace the power window switch
damage
·Right rear power window motor
damage
·Go to Precision Test D
·Short circuit
·Open circuit
Window locking
function is disabled.
·Circuit fault
·Repair the circuit
·Driver’s window locking switch
damage
·Replace the left front window switch
·Replace BCM
Window switch
·Circuit fault
background light isn’t
·Power window switch damage
on
·Repair the circuit
·Replace the power window switch
Landwind X5
501-11-16
Glass, Window Frame and Mechanism
Power window fails to ·Circuit fault
ascend to the top
·Glass guide rail deformation
Landwind X5
501-11-16
·Repair the circuit
·Repair or replace the glass mud
groove
·Glass mud groove damage
·Repair or replace the glass mud
groove
·Door deformation
·Repair the door
501-11-17
Glass, Window Frame and Mechanism
501-11-17
Precision Test
Precision Test A: Left front door power
window doesn’t work
Test Conditions
Details/Results/Measures
Caution: All electrical measurements must be done by a digital multimeter.
A1: Check the left front power window switch fuse FY12(10A) and left front power window fuse
FY11(30A).
1.Check the left front power window switch fuse
FY12(10A) and left front power window fuse
FY11(30A).
Is the fuse normal?
Yes
Go to A2.
No
Replace new fuse with rated capacity and check
the system for normal operation.
E31501110014
A2: Check the left front window regulator motor.
1
2
E31501110015
1.Turn the ignition switch to "LOCK".
2.Disconnect the left front door window regulator
motor harness plug.
3.Turn the ignition switch to "ACC" or "ON".
4.Control the ascending of the front door window
regulator switch and measure the voltage to
ground of terminal 1 of the left front door
window regulator motor harness plug.
Is the voltage higher than 12.6V;
Control the descending of the front door window
regulator switch and measure the voltage to
ground of terminal 2.
Is the voltage higher than 12.6V?
Is the voltage higher than 12.6 V?
Yes
Replace the left front window regulator.
No
Go to A3.
A3: Check the left front window regulator switch circuit PW17 and PW16.
Landwind X5
501-11-18
Glass, Window Frame and Mechanism
1
8
9
16
E31501110016
Landwind X5
501-11-18
1.Turn the ignition switch to "ACC" or "ON".
2.Disconnect the BCM PE2 plug.
3.Control the ascending of the front door window
regulator switch and measure the voltage to
ground of terminal 2 of BCM PE2 plug.
4.Control the descending of the front door window
regulator switch and measure the voltage to
ground of terminal 10 of BCM PE2 plug.
Is the voltage higher than 12.6V?
Yes
Check the mechanical fault of the window
regulator.
No
Replace the left front window regulator switch
assembly.
501-11-19
Glass, Window Frame and Mechanism
501-11-19
Precision Test B: Right front door power
window doesn’t work
Test Conditions
Details/Results/Measures
Caution: All electrical measurements must be done by a digital multimeter.
B1: Check the left front power window switch fuse FY13(10A) and right front power window fuse
FY11(30A).
1.Check the left front power window switch fuse
FY13(10A) and right front power window fuse
FY11(30A).
Is the fuse normal?
Yes
Go to B2?
No
Replace new fuse with rated capacity and check
the system for normal operation.
E31501110017
B2: Check the window regulator switch.
1.Operate the left front door window regulator
switch, does the right front door glass work
normally?
Yes
Replace the right front door window regulator
switch.
No
Go to B3.
2.Operate the right front door window regulator
switch, does the right front door glass work
normally?
Yes
Replace the left front door window regulator switch
assembly.
No
Go to B3.
B3: Check the right front window regulator motor.
Landwind X5
501-11-20
1
Glass, Window Frame and Mechanism
2
E31501110018
Landwind X5
501-11-20
1.Turn the ignition switch to "LOCK".
2.Disconnect the right front door window regulator
motor harness plug.
3.Turn the ignition switch to "ACC" or "ON".
4.Control the ascending of the rear door window
regulator switch and measure the voltage to
ground of terminal 1 of right front door window
regulator motor harness plug.
Is the voltage higher than 12.6V?
Control the decending of the right door window
regulator siwtch and measure the voltage to
ground of terminal 2.
Is the voltage higher than 12.6V?
Is the voltage higher than 12.6 V?
Yes
Replace the right front window regulator.
No
Go to B4.
501-11-21
Glass, Window Frame and Mechanism
501-11-21
B4: Check the right front window regulator switch circuit PW18b and PW15b.
1
8
9
16
E31501110019
1.Turn the ignition switch to "ACC" or "ON".
2. Disconnect the BCM PE2 plug.
3.Control the ascending of the front door window
regulator switch and measure the voltage to
ground of terminal 3 of BCM PE2 plug.
4.Control the descending of the front door window
regulator switch and measure the voltage to
ground of terminal 11 of BCM PE2 plug.
Is the voltage higher than 12.6V?
Yes
Check the mechanical fault of the window
regulator.
No
Check the open circuit or poor contact of circuit
PW18b and PW15b and check the system for
normal operation.
Precision Test C: Left rear door power window
doesn’t work.
Test Conditions
Details/Results/Measures
Caution: All electrical measurements must be done by a digital multimeter.
C1: Check the left front power window switch fuse FY12(10A) and left rear power window fuse
FY11(30A).
1.Check the left front power window switch fuse
FY12(10A) and left rear power window fuse
FY11(30A).
Is the fuse normal?
Yes
Go to C2.
No
Replace new fuse with rated capacity and check
the system form normal operation.
E31501110020
C2: Check the window regulator switch.
Landwind X5
501-11-22
Glass, Window Frame and Mechanism
501-11-22
1.Operate the left front door window regulator
switch,does the left front door window work normally?
Yes
Replace the left rear door window regulator
switch?
No
Go to C3.
2.Operate the left rear door window regulator
switch,does the left rear door window work normally?
Yes
Replace the switch assembly of the left front door
window regulator?
No
Go to C3.
Landwind X5
501-11-23
Glass, Window Frame and Mechanism
501-11-23
C3: Check the left rear window regulator motor.
1
2
E31501110021
1.Turn the ignition switch to "LOCK".
2.Disconnect the right front door window regulator
motor harness plug.
3.Turn the ignition switch to "ACC" or "ON".
4.Control the ascending of the left rear window
regulator and measure the voltage to ground of
terminal 1 of the left rear door window regulator
motor harness plug.
Is the voltage higher than 12.6V;
Control the descending of the left rear window
regulator switch and measure the voltage to
ground of terminal 2.
Is the voltage higher than 12.6V?
Is the voltage higher than 12.6 V?
Yes
Replace the left rear window regulator.
No
Go to C4.
C4: Check the left rear window regulator switch circuit PW25b and PW14.
1
8
9
16
E31501110022
1.Turn the ignition switch to "ACC" or "ON".
2.Disconnec the BCM PE2 plug.
3.Control the ascending of the front window
regulator switch and measure the voltage to
ground of terminal 4 of BCM PE2 plug.
4.Conctrol the descending of the front window
regulator switch and measure the voltage to
ground of terminal 12 of BCM PE2 plug.
Is the voltage higher than 12.6V?
Yes
Check the mechanical fault of the window
regulator.
No
Check the open circuit or poor contact of circuit
PW25b and PW14 and check the system for
normal operation.
Precision Test D: Right rear door power
window doesn’t work.
Test Conditions
Details/Results/Measures
Caution: All electrical measurements must be done by a digital multimeter.
D1: Check left front power window switch fuse FY13(10A) and right rear power window fuse
FY11(30A).
Landwind X5
501-11-24
Glass, Window Frame and Mechanism
501-11-24
1.Check the left front power window switch fuse
FY13(10A) and right rear power window fuse
FY11(30A).
Is the fuse normal?
Yes
Go to D2.
No
Replace new fuse with rated capacity and check
the system for normal operation.
E31501110023
Landwind X5
501-11-25
Glass, Window Frame and Mechanism
501-11-25
D2: Check the window regulator switch.
1.Operate the left front door glass switch, does the
right rear door glass work normally?
Yes
Replace the right rear door window regulator
switch.
No
Go to D3.
2.Operate the right rear door window regulator
switch, does the right rear door glass work
normally?
Yes
Replace the left front door window regulator switch
assembly.
No
Go to D3.
D3: Check the right rear window regulator motor.
1
2
E31501110024
1.Turn the ignition switch to "LOCK".
2.Disconnect the right rear dow window regulator
motor harness plug.
3.Turn the ignition switch to "ACC" or "ON".
4.Control the ascending of the right rear window
regulator switch and measure the voltage to
ground of terminal 1 of the right rear door
window regulator motor harness plug.
Is the voltage higher than 12.6V;
Control the descending of the right rear window
regulator switch and measure the voltage to
ground of terminal 2.
Is the voltage higher than 12.6 V?
Yes
Replace the right rear window regulator.
No
Go to D4.
D4: Check the right rear widnow regulator switch circuit PW26b and PW13b.
Landwind X5
501-11-26
Glass, Window Frame and Mechanism
1
8
9
16
E31501110025
Landwind X5
501-11-26
1.Turn the ignition switch to "ACC" or "ON".
2.Disconnect the BCM PE2 plug.
3.Control the ascending of right rear window
regulator switch and measure the voltage to
ground of terminal 5 of BCM PE2 plug.
4.Control the descending of right rear window
regulator switch and measure the voltage to
ground of terminal 13 of BCM PE2 plug.
Is the voltage higher than 12.6V?
Yes
Check the mechanical fault of the window
regulator.
No
Check the open circuit or poor contact of circuit
PW26b and PW13b and check the system for
normal operation.
501-11-27
Glass, Window Frame and Mechanism
501-11-27
Disassembly and Assembly
Left Front Door Switch Panel
Disassembly
1.Disconnect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
2.Disassemble the left front door switch panel
lower cover plate.
Insert a flat head screwdriver in the seam
between the switch panel lower part and lower
cover plate or the service port, penetrate the
flat head screwdriver in to jack the lower cover
plate and apply force to push the lower cover
plate out from the clamping hole.
E31501110026
3.Disassemble the left front door switch panel.
Caution: The switch panel is firmly installed,
so it’s difficult to remove the switch
panel. Improper operation may damage
the switch panel pin so that the switch
panel may be abandoned or the upper trim
panel coating surface and other surrounding parts may be scratched.
E31501110027
1 Disassembly starts with the back of the
panel, i.e. the end close to the elbow. Firstly
break off the switch panel with hands to
leave a certain gap at the back of the switch
panel, penetrate the screwdriver in it, align it
with the outside clip at the end of the panel,
and pry the clip. Loosen the outside clip at
the end of the panel, further penetrate the
screwdriver in the inside clip at the end and
push the clip out from the snap joint, so as
to make the clip at the end of the switch
panel completely separate from the snap
joint.
2.Insert the screwdriver in the outside clip at
the middle of the panel and apply force to
pry up the clip. Lossen the outside clip at
the middle of the panel, insert the screwLandwind X5
501-11-28
Glass, Window Frame and Mechanism
driver in and align it with the inside clip at
the middle and pry up the clip with the
screw driver. And then, right hand pushes
tightly the imitation leather trim plate, and
left hand uplifts the panel so as to make the
clip at the middle of the panel completely
separate from the snap joint.
Landwind X5
501-11-28
501-11-29
Glass, Window Frame and Mechanism
501-11-29
3.Loosen the clip at the middle of the panel,
align the screwdriver with the front buckle
position of the panel and pry up the buckle.
Pull out the switch harness connector on
the switch panel, complete the removal of
switch panel and take it down.
E31501110028
Assembly
1.The procedures for assembly are the
reverse of the disassembly procedures.
Landwind X5
501-11-30
Glass, Window Frame and Mechanism
501-11-30
Left Front Door Glass
Disassembly
1.Disconnect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
2.Disassemble the left front door switch panel
assembly.
Refer to relevant content of this section.
3.Disassemble the left front door interior
panel.
2
1
E31501110029
Refer to relevant content of 501-05 Interior
Panel and Part.
4.Disassemble the left front door waterproof
membrane.
5.Loosen the left front door rear mobile guide
rail.
1 Disassemble the fixing bolt of the left front
rear mobile guide rail.
2 Push the front door rear mobile guide rail
leftward to make it separate from the glass.
6.Disassemble the fixing bolt of the glass and
window regulator.
×2
Disassemble 2 fixing bolts.
E31501110031
7.Take out the glass.
Caution: Take out the glass and place it in a
safe place to avoid carelessly damaging
the glass.
E31501110031
Landwind X5
501-11-31
Glass, Window Frame and Mechanism
501-11-31
Landwind X5
501-11-32
Glass, Window Frame and Mechanism
501-11-32
Left Front Door Rear Mobile Guide Rail Assembly
Disassembly
1.Disconnect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
2.Disassemble the left front door switch panel
assembly.
Refer to relevant content of this section.
3.Disassemble the left front door interior
panel.
Refer to relevant content of 501-05 Interior
Panel and Part.
4.Disassemble the left front door glass assembly.
Refer to relevant content of this section.
E31501110032
5.Disassemble the fixing bolt of the guide rail.
Disassemble 1 fixing bolt.
6.Disassemble the glass mud groove and take
out the guide rail.
E31501110033
Assembly
Caution: Put the guide rail in the groove in
the assembly.
1.The procedures for assembly are the
reverse of the disassembly procedures.
Landwind X5
501-11-33
Glass, Window Frame and Mechanism
501-11-33
Landwind X5
501-11-34
Glass, Window Frame and Mechanism
501-11-34
Left Front Door Window Regulator
Disassembly
1.Disconnect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
2.Disassemble the left front door switch panel
assembly.
Refer to relevant content of this section.
3.Disassemble the left front door interior
panel.
Refer to relevant content of 501-05 Interior
Panel and Part.
E31501110034
4.Disassemble left front door glass assembly.
Refer to relevant content of this section.
5.Disconnect the window regulator harness
connector.
×6
6.Disassemble the fixing bolt of the window
regulator.
Disassemble 6 fixing bolts.
E31501110035
Assembly
1.The procedures for assembly are the
reverse of the disassembly procedures.
Landwind X5
501-11-35
Glass, Window Frame and Mechanism
501-11-35
Left Rear Door Switch Panel
Disassembly
1.Disconnect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
2.Disassemble the left rear door switch panel
lower cover plate.
Insert a flat head screwdriver in the seam
between the switch panel lower part and lower
cover plate or the service port, penetrate the
flat head screwdriver in to jack the lower cover
plate and apply force to push the lower cover
plate out from the clamping hole.
E31501110036
3.Disassemble the left rear door switch panel.
Caution: The switch panel is firmly
installed, so it’s difficult to remove the
switch panel. Improper operation may damage the switch panel pin so that the switch
panel may be abandoned or the upper trim
panel coating surface and other surrounding parts may be scratched.
E31501110037
E31501110038
1.Disassembly starts with the back of the
panel, i.e. the end close to the elbow.Firstly
break off the switch panel with hands to
leave a certain gap at the back of the switch
panel, penetrate the screwdriver in it, align it
with the outside clip at the end of the panel,
and pry the clip. Loosen the outside clip at
the end of the panel, further penetrate the
screwdriver in the inside clip at the end and
push the clip out from the snap joint, so as
to make the clip at the end of the switch
panel completely separate from the snap
joint.
2.Insert the screwdriver in the outside clip at
the middle of the panel and apply force to
pry up the clip. Loosen the outside clip at
the middle of the panel, insert the screwdriver in and align it with the inside clip at
the middle and pry up the clip with the
screw driver. And then, right hand pushes
tightly the imitation leather trim plate, and
left hand uplifts the panel so as to make the
clip at the middle of the panel completely
separate from the snap joint.
Landwind X5
501-11-36
Glass, Window Frame and Mechanism
3.Loosen the clip at the middle of the panel,
align the screwdriver with the front buckle
position of the panel and pry up the buckle.
Pull out the switch harness connector on
the switch panel, complete the removal of
switch panel and take down it.
Assembly
1.The procedures for assembly are the
reverse of the disassembly procedures.
Landwind X5
501-11-36
501-11-37
Glass, Window Frame and Mechanism
501-11-37
Left Rear Door Mobile Guide Rail
Disassembly
1.Disconnect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
2.Disassemble the left rear door power switch.
Refer to relevant content of this section.
3.Disassemble the left rear door interior panel.
Refer to relevant content of this section.
E31501110039
4.Disassemble the left rear door glass mud
groove.
Pull open the glass mud groove at the left rear
door triangle window.
5.Disassemble the left rear door waterproof
membrane.
6.Disassemble the left rear door rear mobile
guide rail assembly.
Disassemble the fixing bolt of the mobile guide
rail.
7.Take out the mobile guide rail.
E31501110040
Caution: Try not to apply excessive force to
disassemble the guide rail, otherwise, the
rear door glass may be damaged.
One hand holds the glass, the other one
slightly rotates the mobile guide rail to make
the glass separate from the guide rail.
Assembly
1.The procedures for assembly are the
reverse of the disassembly procedures.
Landwind X5
501-11-38
Landwind X5
Glass, Window Frame and Mechanism
501-11-38
501-11-39
Glass, Window Frame and Mechanism
501-11-39
Left Rear Door Triangle Window Glass
Disassembly
1.Disassemble the left rear door mobile guide
rail assembly.
Refer to relevant content of this section.
2.Take out the left rear door triangle window
glass.
Assembly
1.The procedures for assembly are the
reverse of the disassembly procedures.
Landwind X5
501-11-40
Glass, Window Frame and Mechanism
501-11-40
Left Rear Door Glass
Disassembly
1.Disconnect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
2.Disassemble the left rear door power switch.
Refer to relevant content of this section.
3.Disassemble the left rear door interior panel.
Refer to relevant content of this section.
4.Disassemble the rear door mobile guide rail
assembly.
Refer to relevant content of this section.
5.Take the glass out from the window regulator.
E31501110041
Caution: Be specially careful to do this step
to avoid breakage.
1 Lift up the glass in left and side direction and
press it down in the right direction.
2 Gently push the lower part of the glass backward to make the glass holder separate
from the master arm of the window regulator.
E31501110042
Landwind X5
501-11-41
Glass, Window Frame and Mechanism
501-11-41
Landwind X5
501-11-42
Glass, Window Frame and Mechanism
501-11-42
6.Disassemble the left rear door glass assembly.
Caution: Place the glass in a safe place
to avoid breakage.
After the above steps, directly uplift the glass.
E31501110043
Assembly
1.The procedures for assembly are the
reverse of the disassembly procedures.
Landwind X5
501-11-43
Glass, Window Frame and Mechanism
501-11-43
Left Rear Door Window Regulator
Disassembly
1.Disconnect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
2.Disassemble the left rear door power switch.
Refer to relevant content of this section.
3.Disassemble the left rear door interior panel.
Refer to relevant content of this section.
4.Disassemble the left rear door mobile guide
rail assembly.
Refer to relevant content of this section.
5.Disassemble the left rear door glass assembly.
×4
Refer to relevant content of this section.
E31501110044
6.Disassemble the fixing bolt of the window
regulator.
Disassemble 4 fixing bolts.
7.Disconnect the window regulator harness
connector.
Assembly
E31501110045
1.The procedures for assembly are the
reverse of the disassembly procedures.
Landwind X5
501-11-44
Glass, Window Frame and Mechanism
501-11-44
Front Windshield Glass
Disassembly
General Tools
Hot air gun
1.Disconnect the negative cable of the battery.
Mixed/spray gun
Refer to relevant content of 414-01 Battery,
Support and Cable.
Glass sucker
Knife
2.Disassemble the front wiper arm.
Glass glue cutter
Refer to relevant content of 501-16 Wiper
and Washer.
Material
Item
Model
Glass glue
PU310
Glass washing solution
CL111
Primer coating
PR220
3.Disassemble the air chamber cover plate
assembly.
Refer to relevant content of 501-08 Exterior
Panel and Part.
4.Disassemble left and right pillar A interior
panel.
Refer to relevant content of 501-05 Interior
Panel and Part.
5.Disassemble the upper instrument desk
assembly.
Refer to relevant content of 501-12
Instrument Panel and Console.
6.Disassemble the interior rear view mirror
assembly.
Refer to relevant content of 501-05 Interior
Panel and Part.
7.Disassemble the sunshade assembly.
Refer to relevant content of 501-05 Interior
Panel and Part.
Landwind X5
501-11-45
Glass, Window Frame and Mechanism
501-11-45
Landwind X5
501-11-46
Glass, Window Frame and Mechanism
501-11-46
8.Disassemble the reading lamp assembly.
Refer to relevant content of 417-02 Interior
Lighting.
9.Disassemble the roof interior panel assembly.
Refer to relevant content of 501-05 Interior
Panel and Part.
10.Disassemble front windshield foam armor
rod beside the left and right pillar A.
11.Use the glass glue cutter to cut the front
windshield glass glue along the window
sheet metal.
E31501110046
Warning: Wear gloves and safety goggles
when using special tools, as there may be
fragments in the cutting process. Wear ear
plug when cutting. Disobeying these
instructions may cause personal injury.
Caution: Be careful not to damage the vehicle body or the trim panel in the cutting
process.
12.Take down the front windshield glass from
the front windshield glass frame.
Caution: This step needs to be completed
with the help of two service technicians.
E31501110047
Assembly
Caution: The remaining 1mm adhesive is
applied to the edge.
Caution: Try not to contact the surface
being cleaned or applied primer, which
may influence the glass bonding effect.
1.Clear the glass glue on the front windshield
glass and glass window frame.
General tool: knife.
E31501110048
Landwind X5
501-11-47
Glass, Window Frame and Mechanism
501-11-47
Landwind X5
501-11-48
Glass, Window Frame and Mechanism
501-11-48
2.Use the hot air gun to deliver hot air (25°C)
to windscreen edge and glass bonding
seam to dry water.
Caution: To ensure adhesive solidification,
all bonding surfaces must be dry, it’s very
important.
3.Prepare glass, windshield glass edge and
trimmed PU adhesive according to instructions accompanied by the adhesive tool kit.
4.Use the mixed/spray gun to continuously
apply a thin layer of PU adhesive to the
front windshield glass edge.
E31501110049
General tool: mixed/spray gun.
Caution: Abandon the original 100mm PU
adhesive as its service life may be short.
Caution: To avoid water leakage, any
bonding fracture must be covered by
20mm adhesive.
5.Use the mixed/spray gun to apply PU adhesive
to the windshield edge along the bonding
seam, with the height between 8 and 10mm.
General tool: mixed/spray gun.
E31501110050
Caution: Abandon the original 100mm PU
adhesive as its service life may be short.
Caution: To avoid water leakage, any
bonding fracture must be covered by
20mm adhesive.
6.With the help of another technician, use the
glass sucker.
·Press the glass in plate by even force.
General Tool: glass sucker.
E31501110051
7.Use a proper adhesive tape to fix the windshield glass at proper position till the PU
adhesive is solidified.
Caution: In the solidification process of PU
adhesive, the door window must be open
to avoid pressure generated from opening
and closing the door.
Landwind X5
501-11-49
Glass, Window Frame and Mechanism
501-11-49
Landwind X5
501-11-50
Glass, Window Frame and Mechanism
501-11-50
8.If the ambient temperature is below 10°C,
use hot air gun and keep delivering hot
air(25°C) for 15 min (indoor or outdoor).
General tool: hot air gun.
9.Assemble the roof.
50 mm
Refer to relevant content of 501-05 Interior
Panel and Part.
10.Assemble the reading lamp assembly.
E31501110052
Refer to relevant content of 417-02 Interior
Lighting.
11.Assemble the sunshade.
Refer to relevant content of 501-05 Interior
Panel and Part.
12.Assemble interior rear view mirror assembly.
Refer to relevant content of 501-05 Interior
Panel and Part.
13.Assemble left and right pillar A interior
panel.
Refer to relevant content of 501-05 Interior
Panel and Part.
14.Assemble the air chamber cover plate
assembly.
Refer to relevant content of 501-08 Exterior
Panel and Part.
15.Assemble the wiper arm.
Refer to relevant content of 501-16 Wiper
and Washer.
16.Connect the negative cable of the battery.
Refer to relevant content of 414-01 Battery,
Support and Cable.
Landwind X5
501-11-51
Glass, Window Frame and Mechanism
501-11-51
Side Rear Triangle Window Assembly
General Tools
Hot air gun
Mixed/spray gun
Glass sucker
Knife
Glass glue cutter
Hot air gun
Materials
Item
Model
Glass glue
PU310
Glass washing solution
CL111
Disassembly
Primer coating
PR220
1.Disassemble the rear side interior panel.
Refer to relevant content of 501-05 Interior
Panel and Part.
2.Use the blade to cut the glass glue around
the rear triangle window from the interior
of the vehicle.
Caution: To re-assemble the original window glass, try not to damage the sealing
strip.
E31501110053
3.Use a sucker to take down the rear triangle
window glass.
Assembly
1.Clear the glass glue on the side triangle
glass and glass window frame.
General tool: knife.
Caution: The remaining 1mm adhesive is
applied to the edge.
Caution: Ensure the surface to be bonded
clean without foreign matters.
E31501110054
2.Use hot air gun to deliver hot air (25°C)to triangle glass edge and glass bonding seam
to dry water.
Caution: To ensure the solidification of
glass glue, all bonding surfaces must be
dry, it’s very important.
Landwind X5
501-11-52
Glass, Window Frame and Mechanism
3.Prepare glass, triangle glass edge and
trimmed glass glue according to the
instructions accompanied by the glass
glue tool kit.
Landwind X5
501-11-52
501-11-53
Glass, Window Frame and Mechanism
501-11-53
4.Assemble new triangle glass fixing buckle.
5.Use mixed/spray gun to apply a thin layer of
glass glue at the edge of the triangle
glass.
General tool: mixed/spray gun.
E31501110055
Caution: Abandon the original 100mm
glass glue, as its service life may be short.
Caution: To avoid water leakage, any bonding
fracture must be covered by 20mm
adhesive.
6.With the help of another technician, use the
glass sucker.
·Press the glass in plate by even force.
General tool: glass sucker.
7.Use a proper adhesive tape to fix the windshield at proper position till the glass glue
is solidified.
E31501110056
Caution: In the solidification process of the
glass glue, door window must be open to
avoid pressure generated from opening
and closing the door.
8.If the ambient temperature is below 10°C,
use hot air gun and keep delivering hot air
(25°C) for 15 min (indoor or outdoor).
General tool: hot air gun.
50 mm
9.Assemble rear side interior panel.
Refer to relevant content of 501-05 Interior
Panel and Part.
E31501110057
Landwind X5
501-11-54
Glass, Window Frame and Mechanism
501-11-54
Tail Gate Glass
General Tools
Disassembly
Hot air gun
Mixed/spray gun
1.Disassemble the tail gate interior panel.
Glass sucker
Refer to relevant content of 501-05 Interior
Panel and Part.
Knife
glass glue cutter
2.Disassemble the rear wiper and wiper motor.
Refer to relevant content of 501-16 Wiper
and Washer.
Material
Item
Model
Glass glue
PU310
Glass washing solution
CL111
Primer coating
PR220
3.Disassemble the rear guide plate.
Refer to relevant content of 501-08 Exterior
Panel and Part.
4.Use a blade to cut the tail gate glass glue
from the interior of the vehicle.
Assembly
1.Clear the glass glue on the rear back door
glass and glass window frame.
General tool: knife.
Caution: The remaining 1mm adhesive is
applied to the edge.
Caution: Ensure the bonding surface clean
without foreign matters.
E31501110058
Landwind X5
501-11-55
Glass, Window Frame and Mechanism
501-11-55
2.Use hot air gun to deliver hot air (25°C) to
rear back door window edge and glass
bonding seam to dry water.
Caution: To ensure solidification of the
glass glue, all bonding surfaces must be
dry, it’s very important.
Landwind X5
501-11-56
Glass, Window Frame and Mechanism
501-11-56
3.Prepare glass, rear back door glass edge
and trimmed glass glue according to the
instructions accompanied by the adhesive
tool kit.
4.Assemble new rear back door glass fixing
buckle.
5.Use mixed/spray gun to continuously apply
a thin layer of glass glue at the edge of the
triangle glass.
General Tool: mixed/spray gun.
Caution: Abandon the original 100mm
glass glue, as its service life may be
short.
E31501110059
Caution: To avoid water leakage, any bonding fracture must be covered by 20mm
adhesive.
6.With the help of another technician, use the
glass sucker.
·Press the glass in place by even force.
General Tool: glass sucker.
E31501110060
7.Use proper adhesive tape to fix the windshield to proper position till the glass glue
is solidified.
Caution: In the solidification process of the
glass glue, the door window must be
open to avoid pressure generated from
opening and closing the door.
8.If the ambient temperature is below, use the
hot air gun and keep delivering hot air
(25°C) for 15 min(outdoor or indoor).
50 mm
General Tool: hot air gun.
9.Assemble the wiper motor and wiper arm.
E31501110061
Refer to relevant content of 501-16 Wiper
and Washer.
10.Assemble the tail gate interior panel.
Refer to relevant content of 501-05 Interior
Panel and Part.
11.Assemble the guide plate.
Landwind X5
501-11-57
Glass, Window Frame and Mechanism
501-11-57
Refer to relevant content of 501-08 Exterior
Panel and Part.
Landwind X5