Kuhlman Electric Corporation
15000 Volt
Instrument
Transformers
15000 Volt
March 2008
Table of Contents
Description
Model
Page
Wound, Dry-Type VT – Y Burden
PTT-110-977
3-4
Wound, Dry-Type VT – Z Burden (High Accuracy available)
PTT-110-9710(H)
5-6
Wound, Oil-Filled VT – ZZ Burden (High Accuracy available)
SPOF-110 (DB)
7-8
Wound, Dry-Type CT – Standard Range (High Accuracy available)
BB-15-971(H)
9-10
Wound, Dry-Type CT – Extended Range
BB-15-972
11-12
4 ½” Window CT – Single, Dual & Multi Ratio (High Accuracy available)
LG(X)-15-585
13-14
4 ½” Window CT – Single, Dual & Multi Ratio (High Accuracy available)
LG(X)-15-683
15-16
4 ½” Window CT – Single, Dual & Multi Ratio
LG-15-879
17-18
8 ¾” Window CT – Single, Dual & Multi Ratio (High Accuracy available)
LG(X)-15-6513
19-20
Wound, Oil-Filled CT (High Accuracy available)
COF(CXM)-110
21-22
Wound, Dry-Type, Single Phase Metering Unit
KM-15-972
23-24
Wound, Oil-Filled, Single Phase Metering Unit (High Accuracy available)
JS(JXM)-110
25-26
Wound, Oil-Filled, Three Phase Metering Unit (High Accuracy available)
MVCT(MXM)-110
27-28
Wound, Dry-Type, Three Phase CT/VT Metering Rack (High Accuracy available) ME-015
29-30
Wound, Dry-Type, Three Phase Metering Unit Metering Rack
MK-15
31-32
Three Phase Dead-Front CT/VT Metering Cubicle (High Accuracy available)
MP-015
33-34
Indoor, Wound, Dry-Type VT – Z Burden (High Accuracy available)
U/VCD-17(H)
35-36
Indoor, Wound, Dry-Type CT – Standard Range (High Accuracy available)
CID-17(H)
37-38
Indoor, Wound, Dry-Type, Single Phase Dead-Front Metering Unit
KCB-17
39-40
Three Phase Low Profile, Dead-Front Metering Unit Metering Cubicle
MI-15
41-42
2
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
PTT–110–977 Voltage Transformer
15000 Volt
Outdoor 15kV, °110kV BIL, Single & Dual Ratios
Molded Epoxy, Wound Type, Metering/Relaying
March 2008
application
The PTT-110-977 outdoor voltage transformer is rated for use on
5,000 & 15,000 volt systems with °110kV BIL. Primary voltage
ratios are available from 20:1 to 120:1 for use on 5,000 & 15,000
volt systems, at 60 Hertz (Hz). This dry-type, solid-cast voltage
transformer will operate with high accuracy for metering or relay
applications.
mechanical description
The core and coil assembly is wound and encapsulated in a high
dielectric strength epoxy resin to provide high withstand capabilities.
The external line to ground insulation consists of a cycloaliphatic
epoxy resin that provides excellent arc track properties in addition
to ultraviolet resistance and strong physical strength. The primary
terminal(s) are M12 stud with a compression type lug for #8 - #2
AWG conductors. The clamp-type post secondary terminals have
¼”-20 slotted screws and associated hardware located inside a
removable terminal box with two (2) 1” NPT conduit hubs and a
1” knockout on the bottom of the box.
accuracy performance
The PTT-110-977 will operate with 0.3 Class accuracy for
metering and relay applications with burdens of 0, W, X, M and Y.
The transformer is accurate from 90% to 110% of rated primary
voltage.
mounting
The PTT is designed for mounting on poles or substation structures
in an upright, underhung or cantilever position. The mounting
holes in the heavy galvanized steel plate are punched to industry
standard dimensions for interchangeability in the field.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 120% of the nominal system voltage.
options
Units are available in single or double bushing models. Contact
factory for other needs.
ORDERING INFO FOR PTT-110-977(G)
Ratio
Primary°
Secondary
20:1
35:1
40:1
42:1
60:1
63.5:1
66.4:1
66.67:1
70:1
70/120:1
100:1
110:1
115:1
120:1
2400
4200
4800
5040
7200
7620
7920
8000
8400
8400
12000
13200
13800
14400
120
120
120
120
120
120
120
120
120
120/70
120
120
120
120
HIGH ACCURACY N/A
Catalog Number*
1 Bushing°
2 Bushing
B913G020S0
---D913G060S0
D913G063S0
D913G066S0
D913G067S0
D913G070S0
D913G070D0
-----
D913020S0
D913035S0
D913040S0
D913042S0
D913060S0
D913063S0
D913066S0
-D913070S0
-D913100S0
D913110S0
D913115S0
D913120S0
Accuracy/
Burden
Catalog
Number
Accuracy/
Burden
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y
---------------
---------------
- Thermal Burden Rating (Typical): Single Bushing (750VA), Double Bushing (1000VA).
- Overvoltage Rating: 1.1x cont.
° Single Bushing units with less than 5kV primary voltage are rated 60kV BIL.
* All units are RUS accepted and IC Approval AE-0967 is noted by bold catalog number.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
3
15000 Volt
March 2008
4
PTT–110–977 Voltage Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
PTT–110–9710(H) Voltage Transformer
Outdoor 15kV, °110kV BIL, Single & Dual Ratios (w/ Tertiary)
Molded Epoxy, Wound Type, Metering/Relaying
15000 Volt
March 2008
application
The PTT-110-9710(H) outdoor voltage transformer is rated for use
on 5,000 & 15,000 volt systems with °110kV BIL. Primary voltage
ratios are available from 20:1 to 120:1 for use on 5,000 & 15,000
volt systems, at 60 Hertz (Hz). This dry-type, solid-cast voltage
transformer will operate with high accuracy for metering or relay
applications.
mechanical description
The core and coil assembly is wound and encapsulated in a high
dielectric strength epoxy resin to provide high withstand capabilities.
The external line to ground insulation consists of a cycloaliphatic
epoxy resin that provides excellent arc track properties in addition
to ultraviolet resistance and strong physical strength. The primary
terminal(s) are M12 stud with a compression type lug for #8 - #2
AWG conductors. The clamp-type post secondary terminals have
¼”-20 slotted screws and associated hardware located inside a
removable terminal box with two (2) 1” NPT conduit hubs and a
1” knockout on the bottom of the box.
accuracy performance
The PTT-110-9710 will operate with 0.3 Class accuracy for
metering and relay applications with burdens of 0, W, X, M, Y
and Z. The PTT-110-9710H will operate with 0.15 Class high
accuracy for metering applications with burdens of 0, W, X, M
and Y. The transformer is accurate from 90% to 110% of rated
primary voltage.
standard dimensions for interchangeability in the field.
mounting
The PTT is designed for mounting on poles or substation structures
in an upright, underhung or cantilever position. The mounting
holes in the heavy galvanized steel plate are punched to industry
options
Units are available with dual system voltage ratings and/or in single
or double bushing models. The PTT-110-9710H high accuracy
voltage transformer is only available in the double bushing model.
Contact factory for other needs.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 120% of the nominal system voltage.
ORDERING INFO FOR PTT-110-9710(G)
Ratio
Primary°
Secondary
20:1
20/60:1
30:1
35:1
40:1
60:1
60:1:1
63.5:1
63.5:1:1
70:1
70:1:1
100:1
110:1
120:1
120:1:1
2400
2400/7200
3600
4200
4800
7200
7200
7620
7620
8400
8400
12000
13200
14400
14400
120
120
120
120
120
120
120 & 120
120
120 & 120
120
120 & 120
120
120
120
120
Catalog Number*
1 Bushing°
2 Bushing
B914G020S0
D914060P020G0
---D914G060S0
-D914G063S0
D914G063Y0
D914G070S0
------
D914020S0
-D914030S0
D914035S0
D914040S0
D914060S0
D914060Y0
D914063S0
-D914070S0
D914070Y0
D914100S0
D914110S0
D914120S0
D914120Y0
Accuracy/
Burden
0.3 0,W,X,M,Y,Z
0.3 0 to X / Y
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y
HIGH ACCURACY PTT-110-9710H
Catalog Number
Accuracy/
Burden
2 Bushing Only
D914020E0
--D914035E0
D914040E0
D914060E0
-D914063E0
-D914070E0
-D914100E0
D914110E0
D914120E0
--
0.15 0,W,X,M,Y
--0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
-0.15 0,W,X,M,Y
-0.15 0,W,X,M,Y
-0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
--
- Thermal Burden Rating (Typical): Std Acc, Single Ratio (1500VA), Dual Ratio (1000VA max), High Acc. (1000VA).
- Overvoltage Rating (Typical): 1.1x cont.
° Single Bushing units with less than 5kV primary voltage are rated 60kV BIL.
* All units are RUS accepted and IC Approval AE-1391 is noted by bold catalog number.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
5
15000 Volt
March 2008
6
PTT–110–9710(H) Voltage Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
SPOF–110 (DB) Voltage Transformer
15000 Volt
Outdoor 15kV, 110kV BIL, Single & Dual Ratios (w/ Tertiary)
Oil-Filled, Wound Type, Metering/Relaying
March 2008
application
The SPOF-110 (DB) outdoor voltage transformer is rated for use
on 15,000 volt systems with 110kV BIL. Primary voltage ratios are
available from 20:1 to 120:1 for use on 5,000 & 15,000 volt systems,
at 60 Hertz (Hz). This oil-filled voltage transformer will operate with
high accuracy for metering or relay applications.
mechanical description
The tank is a standard distribution transformer tank made of heavy
gauge sheet steel with a seam welded bottom plate and a dome
shaped cover. The tank is washed and coated with anticorrosive
iron phosphate and then finished with a Munsel 70 Gray baked-on
electrostatic polyester powder. The primary bushing(s) are high
strength porcelain with tin plated bronze, eye bolt terminal(s) that
accept #8 - #2 AWG conductors and are locked with silicon bronze
locking hardware. The secondary terminals consist of a feed thru
block with ¼”-20 copper studs and associated hardware located
inside a removable terminal box with three (3) 1 ½” NPT conduit
hubs. The ground terminal is a ½”-13 pad. The unit is fitted with
a pressure relief valve.
accuracy performance
The SPOF-110 (DB) will operate with 0.3 Class accuracy for
metering applications with burdens of 0, W, X, M, Y, Z and ZZ.
Upon request, 0.15 metering accuracy is available for burdens of
0, W, X, M, Y and Z, as well as 0.3 ZZ. The transformer is accurate
from 90% to 110% of rated primary voltage.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Additional tests include dissipation and partial discharge tests.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 135% of the nominal system voltage.
mounting
The SPOF is designed for mounting on poles or substation
structures in an upright position with ANSI type “A” hanger brackets
or optional mounting feet. NOTE: Must be installed per NESC
electrical clearances.
options
The SPOF is available in single or double bushing models, with
NEMA 4-hole Primary Terminal(s), Mounting Feet, a 5kV H0
Bushing, Stainless Steel Tank, Oil Level Gauge, Oil Drain Valve,
and/or -50°C oil. Contact factory for other needs.
ORDERING INFO FOR SPOF-110 (DB)
Ratio
Primary
Secondary
60:1:1
60/100:1:1
63.5:1:1
70:1:1
70/120:1
70/120:1:1
100:1:1
110:1:1
120:1:1
7200
7200
7620
8400
8400
8400
12000
13200
14400
120 & 120
120/72 & 120/72
120 & 120
120 & 120
120/70
120/70 & 120/70
120 & 120
120 & 120
120 & 120
HIGH ACCURACY SPOF-110 (DB)
Catalog Number
1 Bushing
2 Bushing
D830060YA
D830100TA
D830063YA
D830070YA
*D830120DA
D830120TA
----
D840060YA
D840100TA
D840063YA
D840070YA
D840120DA
D840120TA
D840100YA
D840110YA
**D840120YA
Accuracy/
Burden
Catalog
Number
Accuracy/
Burden
0.3 0,W,X,M,Y,Z,ZZ
0.3 0,W,X,M,Y,Z,ZZ
0.3 0,W,X,M,Y,Z,ZZ
0.3 0,W,X,M,Y,Z,ZZ
0.3 0,W,X,M,Y,Z,ZZ
0.3 0,W,X,M,Y,Z,ZZ
0.3 0,W,X,M,Y,Z,ZZ
0.3 0,W,X,M,Y,Z,ZZ
0.3 0,W,X,M,Y,Z,ZZ
Add
“AAEW”
to the
end
of the
standard
catalog
number
0.15 0 to Z/0.3 ZZ
0.15 0 to Z/0.3 ZZ
0.15 0 to Z/0.3 ZZ
0.15 0 to Z/0.3 ZZ
0.15 0 to Z/0.3 ZZ
0.15 0 to Z/0.3 ZZ
0.15 0 to Z/0.3 ZZ
0.15 0 to Z/0.3 ZZ
0.15 0 to Z/0.3 ZZ
- Thermal Burden Rating (Typical): 5000VA.
- Overvoltage Rating: 1.1x cont., 1.9x 8 hours.
- IC Approval *(AE-0724), **(AE-0669 Rev. 1).
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
7
15000 Volt
March 2008
8
SPOF–110 (DB) Voltage Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
BB–15–971(H) Current Transformer
15000 Volt
Outdoor 15kV, 110kV BIL, Single & Dual Ratios
Molded Epoxy, Wound Type, Metering/Relaying
March 2008
application
The BB-15-971(H) outdoor current transformer is rated for use
on 15,000 volt systems with 110kV BIL. Primary current ratios
are available from 5:5 to 1200:5 at 60 Hertz (Hz) with a Rating
Factor of up to 1.5 (1200A max). This dry-type, solid-cast current
transformer will operate with high accuracy for metering or relay
applications.
mechanical description
The core and coil assembly is wound and encapsulated in a high
dielectric strength epoxy resin to provide high withstand capabilities.
The external line to ground insulation consists of a cycloaliphatic
epoxy resin that provides excellent arc track properties in addition
to ultraviolet resistance and strong physical strength. A high voltage
stress ring around the top of the unit is supplied to control RIV
and partial discharge. The primary terminals are flat, tin-plated
copper with standard NEMA 2-hole pattern suitable for various
size conductors. The clamp-type post secondary terminals have
¼”-20 slotted screws and associated hardware located inside a
removable terminal box with two (2) 1” NPT conduit hubs and a
1” knockout on the bottom of the box.
accuracy performance
The BB-15-971 will operate with 0.3 Class accuracy for metering
with burdens of B0.1 to B1.8 and T150 for relay applications. The
transformer is accurate through its Rating Factor, and can be used
continuously to this level. The BB-15-971H will operate with 0.15
Class high accuracy for metering applications with burdens of B0.1
to B0.9. The transformer maintains 0.15 accuracy from 10% (0.3
accuracy from 2%) of Inom through its Rating Factor, and can be
used continuously to this level.
mounting
The BB is designed for mounting on poles or substation structures
in an upright, underhung or cantilever position. The mounting
holes in the heavy galvanized steel plate are punched to industry
standard dimensions for interchangeability in the field.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 120% of the nominal system voltage.
options
A primary spark gap is available for capacitor bank or other
applications where high transients will be present. 90° angle
primary bus adapters can be supplied to place the two terminal
surfaces parallel to one another. Contact factory for other
needs.
ORDERING INFO FOR BB-15-971
Ratio
Catalog
Number*
5:5
10:5
D9060005S0
D9060010S0
HIGH ACCURACY BB-15-971H
Accuracy/Burden
Metering
Relay
0.3 B1.8
0.3 B1.8
T150
T150
Rating
Factor
Catalog
Number*
Accuracy/
Burden
Rating
Factor
1.5
1.5
D9060005E0
D9060010E0
0.15 B0.9
0.15 B0.9
1.5
1.5
…
…
…
…
…
…
…
…
50:5
75:5
100:5
D9060050S0
D9060075S0
D9060100S0
0.3 B1.8
0.3 B1.8
0.3 B1.8
T150
T150
T150
1.5
1.5
1.5
D9060050E0
D9060075E0
D9060100E0
0.15 B0.9
0.15 B0.9
0.15 B0.9
1.5
1.5
1.5
…
…
…
…
…
…
…
…
600:5
800:5
1000:5
1200:5
D9060600S0
D9060800S0
D9061000S0
D9061200S0
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
T150
T150
T150
T150
1.5
1.5
1.2
1.0
D9060600E0
D9060800E0
D9061000E0
D9061200E0
0.15 B0.9
0.15 B0.9
0.15 B0.9
0.15 B0.9
1.5
1.5
1.2
1.0
5/10:5
10/20:5
D9060005D0
D9060010D0
0.3 B0.5/B1.8
0.3 B0.5/B1.8
T75/T150
T75/T150
2.0/1.5
2.0/1.5
D9060005F0
D9060010F0
0.15 B0.5/B0.9
0.15 B0.5/B0.9
2.0/1.5
2.0/1.5
…
…
…
…
…
…
…
…
300/600:5
400/800:5
500/1000:5
600/1200:5
D9060300D0
D9060400D0
D9060500D0
D9060600D0
0.3 B0.5/B1.8
0.3 B0.5/B1.8
0.3 B0.5/B1.8
0.3 B0.5/B1.8
T75/T150
T75/T150
T75/T150
T75/T150
2.0/1.5
1.2/1.2
1.0/1.0
1.0/1.0
D9060300F0
D9060400F0
D9060500F0
D9060600F0
0.15 B0.5/B0.9
0.15 B0.5/B0.9
0.15 B0.5/B0.9
0.15 B0.5/B0.9
2.0/1.5
1.2/1.2
1.0/1.0
1.0/1.0
- 1 Second Thermal/Mechanical Rating: 100x/200x full winding Inom (75x/150x for above 600:5 & 300/600:5).
* All units are RUS accepted and IC Approval AE-0785 is noted by bold catalog number.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
9
15000 Volt
March 2008
10
BB–15–971(H) Current Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
BB–15–972 Current Transformer
Outdoor 15kV, 110kV BIL, Single Ratios
Molded Epoxy, Wound Type, Metering
15000 Volt
March 2008
application
The BB-15-972 outdoor extended range current transformer is
rated for use on 15,000 volt systems with 110kV BIL. Primary
current ratios are available from 5:5 to 1200:5 at 60 Hertz (Hz)
with a Rating Factor of up to 3.0 (1200A max). This dry-type,
solid-cast current transformer will operate with high accuracy for
metering applications.
mechanical description
The core and coil assembly is wound and encapsulated in a high
dielectric strength epoxy resin to provide high withstand capabilities.
The external line to ground insulation consists of a cycloaliphatic
epoxy resin that provides excellent arc track properties in addition
to ultraviolet resistance and strong physical strength. A high voltage
stress ring around the top of the unit is supplied to control RIV
and partial discharge. The primary terminals are flat, tin-plated
copper with standard NEMA 2-hole pattern suitable for various
size conductors. The clamp-type post secondary terminals have
¼”-20 slotted screws and associated hardware located inside a
removable terminal box with two (2) 1” NPT conduit hubs and a
1” knockout on the bottom of the box.
accuracy performance
The BB-15-972 will operate with 0.3 Class accuracy for metering
with burdens of B0.1 to B0.5. The transformer is accurate through
its Rating Factor, and can be used continuously to this level.
mounting
The BB is designed for mounting on poles or substation structures
in an upright, underhung or cantilever position. The mounting
holes in the heavy galvanized steel plate are punched to industry
standard dimensions for interchangeability in the field.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 120% of the nominal system voltage.
options
A primary spark gap is available for capacitor bank or other
applications where high transients will be present. 90° angle
primary bus adapters can be supplied to place the two terminal
surfaces parallel to one another. Contact factory for other
needs.
ORDERING INFO FOR BB-15-972
Ratio
Catalog
Number*
5:5
10:5
15:5
20:5
25:5
30:5
40:5
50:5
75:5
100:5
150:5
200:5
300:5
400:5
600:5
800:5
1000:5
1200:5
D9070005S0
D9070010S0
D9070015S0
D9070020S0
D9070025S0
D9070030S0
D9070040S0
D9070050S0
D9070075S0
D9070100S0
D9070150S0
D9070200S0
D9070300S0
D9070400S0
D9070600S0
D9070800S0
D9071000S0
D9071200S0
HIGH ACCURACY N/A
Accuracy/Burden
Metering
Relay
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
-------------------
Rating
Factor
Catalog
Number
Accuracy/
Burden
Rating
Factor
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.0
1.5
1.2
1.0
-------------------
-------------------
-------------------
- 1 Second Thermal/Mechanical Rating: 150x/300x Inom (120x/240x for 400:5, 100x/200x for 600:5, 75x/150x for above 600:5).
* All units are RUS accepted.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
11
15000 Volt
March 2008
12
BB–15–972 Current Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
LG(X)–15–585 Current Transformer
15000 Volt
Outdoor 15kV, 110kV BIL, Single, Dual & Multi Ratios
Molded Resin, Window Type, Metering/Relaying
application
The LG(X)-15-585 outdoor, window-type current transformer is
rated for use on 15,000 volt systems with 110kV BIL. Primary
current ratios are available from 200:5 to 5000:5 at 60 Hertz (Hz)
with a Rating Factor of up to 4.0. This dry-type, solid-cast current
transformer will operate with high accuracy for metering or relay
applications.
mechanical description
The core and coil assembly is wound and encapsulated in a molded
cast resin with a 4 ½” window porcelain primary bushing to provide
high withstand capabilities. The high strength porcelain has a semi
conductive interior with a pigtail lead to be connected to the primary
conductor to equalize the voltage and prevent radio interference
and corona. An optional primary bus bar with NEMA 4-hole pads
can also be provided (5500A max). The secondary terminals are
¼”-20 copper studs with associated hardware located inside a
removable terminal box with two (2) 1” NPT conduit hubs.
accuracy performance
The LG-15-585 will operate with 0.3 Class accuracy for metering
with burdens of B0.1 up to B1.8 and up to C800 for some relay
applications. The transformer is accurate through its Rating Factor,
and can be used continuously to this level. The LGX-15-585 will
operate with 0.15 Class high accuracy for metering applications
with burdens of B0.1 up to B1.8. The transformer maintains 0.3
accuracy from 1% of Inom through its Rating Factor, and can be
used continuously to this level (for 0.15 accuracy range, see ratings
specific to each ratio).
March 2008
mounting
The LG is designed for
mounting in the upright
or underhung position
with the tube horizontal,
or in the cantilever
position with the tube
vertical. CAUTION:
Do not mount in the
cantilever position with
the tube horizontal, the
base plate can collapse.
Mounting holes are
punched in the aluminum
base plate.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free
of partial discharge through 120% of the nominal system voltage.
The unit is tested above operating voltage for traces of corona. A
“corona free” label is bonded to the completed transformer as a
guarantee of trouble-free service.
options
The LG is available with a primary bus bar kit or conductive bird
guards to prevent foreign objects from entering the porcelain
window. Contact factory for other needs.
ORDERING INFO FOR LG-15-585
HIGH ACCURACY LGX-15-585
Accuracy/Burden
Metering
Relay
Ratio
Catalog
Number*
Rating
Factor
Catalog
Number
0.15/0.3 @
Burden
0.15/0.3
Acc Range
Rating
Factor
200:5
300:5
400:5
500:5
600:5
800:5
1000:5
1200:5
1500:5
2000:5
2500:5
3000:5
4000:5
5000:5
D030200S1
D030300S1
D030400S1
D030500S1
D030600S1
D030800S1
D031000S1
D031200S1
D031500S1
D032000S1
D032500S1
D033000S1
D034000S1
D035000S1
0.3 B0.2
0.3 B0.5
0.3 B0.9
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
C60
C100
C120
C150
C200
C300
C350
C400
C500
C600
C800
C800
C800
C800
3.0
3.0
3.0
3.0
3.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
1.5
1.1
--D030400X1
D030500X1
D030600X1
D030800X1
D031000X1
D031200X1
D031500X1
D032000X1
-----
--B0.5/B0.9
B0.5/B1.8
B0.9/B1.8
B0.9/B1.8
B1.8
B1.8
B1.8
B1.8
-----
--400/4 to 1200A
500/5 to 2000A
600/6 to 2400A
800/8 to 3200A
10 to 4000A
12 to 4800A
15 to 4500A
20 to 4000A
-----
--3.0
4.0
4.0
4.0
4.0
4.0
3.0
2.0
-----
200/400:5
300/600:5
400/800:5
600/1200:5
1000/2000:5
1500/3000:5
D030200D1
D030300D1
D030400D1
D030600D1
D031000D1
D031500D1
0.3 B0.5/B0.9
0.3 B0.5/B1.8
0.3 B0.9/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
C60/C120
C100/C200
C150/C300
C200/C400
C300/C600
C400/C800
3.0/3.0
3.0/3.0
2.0/2.0
2.0/2.0
2.0/2.0
2.0/2.0
-------
-------
-------
-------
- Available in multi-ratio designs (full tap ratings same as single ratio above).
- 1 Second Thermal/Mechanical Rating: 80x full winding Inom / Unlimited mechanical.
- Available with a primary bar kit (maximum 5500A). Change last digit of catalog from 1 to 3.
* IC Approval AE-0703 is noted by bold catalog number.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
13
15000 Volt
March 2008
14
LG(X)–15–585 Current Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
LG(X)–15–683 Current Transformer
15000 Volt
Outdoor 15kV, 110kV BIL, Single, Dual & Multi Ratios
Molded Resin, Window Type, Metering/Relaying
application
The LG(X)-15-683 outdoor, window-type current transformer is
rated for use on 15,000 volt systems with 110kV BIL. Primary
current ratios are available from 200:5 to 5,000:5 at 60 Hertz (Hz)
with a Rating Factor of up to 4.0. This dry-type, solid-cast current
transformer will operate with high accuracy for metering or relay
applications.
mechanical description
The core and coil assembly is wound and encapsulated in a molded
cast resin with a 4 ½” window porcelain primary bushing to provide
high withstand capabilities. The high strength porcelain has a semi
conductive interior with a pigtail lead to be connected to the primary
conductor to equalize the voltage and prevent radio interference
and corona. An optional primary bus bar with NEMA 4-hole pads
can also be provided (5500A max). The secondary terminals are
¼”-20 copper studs with associated hardware located inside a
removable terminal box with two (2) 1” NPT conduit hubs.
accuracy performance
The LG-15-683 will operate with 0.3 Class accuracy for metering
with burdens of B0.1 up to B1.8 and up to C800 for some relay
applications. The transformer is accurate through its Rating Factor,
and can be used continuously to this level. The LGX-15-683 will
operate with 0.15 Class high accuracy for metering applications
with burdens of B0.1 up to B1.8. The transformer maintains 0.3
accuracy from 1% of Inom through its Rating Factor, and can be
used continuously to this level (for 0.15 accuracy range, see ratings
specific to each ratio).
March 2008
mounting
The LG is designed for
mounting in the upright,
underhung or cantilever
position. Open end
slots are provided on
the aluminum mounting
legs.
testing
The unit is individually
tested per the IEEE
C57.13 standard,
including applied
and induced voltage,
accuracy and polarity.
Partial discharge
testing is performed to
guarantee the unit is
free of partial discharge
through 120% of the nominal system voltage. The unit is tested
above operating voltage for traces of corona. A “corona free”
label is bonded to the completed transformer as a guarantee of
trouble-free service.
options
The LG is available with a primary bus bar kit or conductive bird
guards to prevent foreign objects from entering the porcelain
window. Contact factory for other needs.
ORDERING INFO FOR LG-15-683
HIGH ACCURACY LGX-15-683
Accuracy/Burden
Metering
Relay
Rating
Factor
Catalog
Number
0.15/0.3 @
Burden
0.15/0.3
Acc Range
Rating
Factor
Ratio
Catalog
Number*
200:5
300:5
400:5
500:5
600:5
800:5
1000:5
1200:5
1500:5
2000:5
2500:5
3000:5
4000:5
5000:5
D100200S1
D100300S1
D100400S1
D100500S1
D100600S1
D100800S1
D101000S1
D101200S1
D101500S1
D102000S1
D102500S1
D103000S1
D104000S1
D105000S1
0.3 B0.2
0.3 B0.5
0.3 B0.9
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
C50
C100
C100
C150
C200
C200
C250
C250
C300
C400
C400
C800
C800
C800
3.0
3.0
3.0
3.0
3.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
1.5
1.1
--D100400X1
D100500X1
D100600X1
D100800X1
D101000X1
D101200X1
D101500X1
D102000X1
-----
--B0.5/B0.9
B0.5/B1.8
B0.9/B1.8
B0.9/B1.8
B1.8
B1.8
B1.8
B1.8
-----
--400/4 to 1200A
500/5 to 2000A
600/6 to 2400A
800/8 to 3200A
10 to 4000A
12 to 4800A
15 to 4500A
20 to 4000A
-----
--3.0
4.0
4.0
4.0
4.0
4.0
3.0
2.0
-----
200/400:5
300/600:5
400/800:5
600/1200:5
1000/2000:5
1500/3000:5
D100200D1
D100300D1
D100400D1
D100600D1
D101000D1
D101500D1
0.3 B0.5/B0.9
0.3 B0.5/B1.8
0.3 B0.9/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
C50/C100
C100/C200
C100/C200
C200/C400
C200/C400
C400/C800
3.0/3.0
2.0/2.0
2.0/2.0
2.0/2.0
2.0/2.0
2.0/2.0
-------
-------
-------
-------
- Available in multi-ratio designs (full tap ratings same as single ratio above).
- 1 Second Thermal/Mechanical Rating: 80x full winding Inom / Unlimited mechanical.
- Available with a primary bar kit (maximum 5500A). Change last digit of catalog from 1 to 3.
* IC Approval AE-0745 for 2000:5 MR.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
15
15000 Volt
March 2008
16
LG(X)–15–683 Current Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
LG–15–879 Current Transformer
15000 Volt
Outdoor 15kV, 110kV BIL, Single, Dual & Multi Ratios
Molded Resin, Window Type, Metering/Relaying
March 2008
application
The LG-15-879 outdoor, window-type current transformer is rated
for use on 15,000 volt systems with 110kV BIL. Primary current
ratios are available from 200:5 to 10,000:5 for 60 Hertz (Hz) with
a Rating Factor of up to 2.0. This dry-type, solid-cast current
transformer will operate with high accuracy for metering or relay
applications.
vertical. CAUTION: Do
not mount in the cantilever
position with the tube
horizontal, the base plate
can collapse. Mounting
holes are punched in the
aluminum base plate.
mechanical description
The core and coil assembly is wound and encapsulated in a molded
cast resin with a 4 ½” window porcelain primary bushing to provide
high withstand capabilities. The high strength porcelain has a semi
conductive interior with a pigtail lead to be connected to the primary
conductor to equalize the voltage and prevent radio interference
and corona. An optional primary bus bar with NEMA 4-hole pads
can also be provided (5500A max). The secondary terminals are
¼”-20 copper studs with associated hardware located inside a
removable terminal box with two (2) 1” NPT conduit hubs.
testing
The unit is individually
tested per the IEEE
C57.13 standard,
including applied and
induced voltage,
accuracy and polarity.
Partial discharge testing
is performed to guarantee
the unit is free of partial
discharge through 120% of the nominal system voltage. The unit
is tested above operating voltage for traces of corona. A “corona
free” label is bonded to the completed transformer as a guarantee
of trouble-free service.
accuracy performance
The LG-15-879 will operate with 0.3 Class accuracy for metering
with burdens of B0.1 up to B1.8 and up to C800 for some relay
applications. The transformer is accurate through its Rating Factor,
and can be used continuously to this level.
mounting
The LG is designed for mounting in the upright or underhung position
with the tube horizontal, or in the cantilever position with the tube
options
The LG is available with a primary bus bar kit or conductive bird
guards to prevent foreign objects from entering the porcelain
window. The unit can be offered in single, dual or multiple core
designs. Contact factory for other needs.
ORDERING INFO FOR LG-15-879
Catalog
Number
Ratio
200:5
300:5
400:5
600:5
800:5
1000:5
1200:5
1500:5
2000:5
2500:5
3000:5
4000:5
5000:5
HIGH ACCURACY N/A
Accuracy/Burden
Metering
Relay
Rating
Factor
Catalog
Number
0.15 Accuracy
Range
Rating
Factor
6000:5
8000:5
10000:5
D092015S159-1
D093015S209-1
D094015S309-1
D096015S409-1
D098015S609-1
D091025S809-1
D091225S809-1
D091525S809-1
D092025S809-1
D092525S809-1
D093025S809-1
D094025S809-1
D095025S809-1
D096025S809-1
D098025S809-1
D091035S809-1
0.3 B0.1
0.3 B0.2
0.3 B0.5
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
C150
C200
C300
C400
C600
C800
C800
C800
C800
C800
C800
C800
C800
C800
C800
C800
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
1.5
1.5
1.5
1.5
1.25
1.0
-----------------
-----------------
-----------------
200/400:5
300/600:5
400/800:5
600/1200:5
1000/2000:5
1500/3000:5
D092015D109-1
D093015D209-1
D094015D309-1
D096015D409-1
D091025D409-1
D091525D809-1
0.3 B0.5/B0.9
0.3 B0.5/B1.8
0.3 B0.9/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
C100/C200
C200/C400
C300/C600
C400/C800
C400/C800
C800/C800
2.0/2.0
2.0/2.0
2.0/2.0
2.0/2.0
2.0/2.0
2.0/1.5
-------
-------
-------
- Available in multi-ratio designs (full tap ratings same as single ratio above).
- 1 Second Thermal/Mechanical Rating: 80x full winding Inom / Unlimited mechanical.
- Available with a primary bar kit (maximum 5500A). Change last digit of catalog from 1 to 3.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
17
15000 Volt
March 2008
18
LG–15–879 Current Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
LG(X)–15–6513 Current Transformer
15000 Volt
Outdoor 15kV, 110kV BIL, Single, Dual & Multi Ratios
Molded Resin, Window Type, Metering/Relaying
application
The LG(X)-15-6513 outdoor, window-type current transformer is
rated for use on 15,000 volt systems with 110kV BIL. Primary
current ratios are available from 400:5 to 10,000:5 at 60 Hertz
(Hz) with a Rating Factor of up to 4.0. This dry-type, solid-cast
current transformer will operate with high accuracy for metering
or relay applications.
mechanical description
The core and coil assembly is wound and encapsulated in a molded
cast resin with a 8 ¾” window porcelain primary bushing to provide
high withstand capabilities. The high strength porcelain has a semi
conductive interior with a pigtail lead to be connected to the primary
conductor to equalize the voltage and prevent radio interference
and corona. The secondary terminals are ¼”-20 copper studs with
associated hardware located inside a removable terminal box with
two (2) 1” NPT conduit hubs.
March 2008
mounting
The LG is designed for
mounting in the upright
or underhung position
with the tube horizontal,
or in the cantilever
position with the tube
vertical. CAUTION:
Do not mount in the
cantilever position with
the tube horizontal,
the base plate can
collapse. Mounting
holes are punched in the
aluminum base plate.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free
of partial discharge through 120% of the nominal system voltage.
The unit is tested above operating voltage for traces of corona. A
“corona free” label is bonded to the completed transformer as a
guarantee of trouble-free service.
accuracy performance
The LG-15-6513 will operate with 0.3 Class accuracy for metering
with burdens of B0.1 up to B1.8 and up to C800 for some relay
applications. The transformer is accurate through its Rating Factor,
and can be used continuously to this level. The LGX-15-6513 will
operate with 0.15 Class high accuracy for metering applications
with burdens of B0.1 up to B0.9. The transformer maintains 0.3
accuracy from 1% of Inom through its Rating Factor, and can be options
used continuously to this level (for 0.15 accuracy range, see ratings The LG can be offered in single or dual core designs. Contact
factory for other needs.
specific to each ratio).
ORDERING INFO FOR LG-15-6513
HIGH ACCURACY LGX-15-6513
Accuracy/Burden
Metering
Relay
Rating
Factor
Catalog
Number
0.15/0.3 @
Burden
0.15/0.3
Acc Range
Rating
Factor
Ratio
Catalog
Number*
200:5
300:5
400:5
600:5
800:5
1000:5
1200:5
1500:5
2000:5
2500:5
3000:5
4000:5
5000:5
6000:5
8000:5
10000:5
D040200S1
D040300S1
D040400S1
D040600S1
D040800S1
D041000S1
D041200S1
D041500S1
D042000S1
D042500S1
D043000S1
D044000S1
D045000S1
D046000S1
D048000S1
D0410000S1
0.3 B0.2
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.9
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
C50
C100
C100
C150
C200
C250
C300
C300
C400
C600
C800
C800
C800
C800
C800
C800
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
1.5
1.5
1.0
1.0
1.0
--D040400X1
D040600X1
D040800X1
D041000X1
D041200X1
D041500X1
D042000X1
--------
--B0.5
B0.9
B0.9
B0.9
B0.9
B0.9
B0.9
--------
--400/4 to 1200A
600/6 to 2400A
800/8 to 3200A
100/10 to 3000A
120/12 to 3600A
150/15 to 3000A
200/20 to 4000A
--------
--3.0
4.0
4.0
3.0
3.0
2.0
2.0
--------
200/400:5
300/600:5
400/800:5
600/1200:5
1000/2000:5
1500/3000:5
2000/4000:5
3000/6000:5
D040200D1
D040300D1
D040400D1
D040600D1
D041000D1
D041500D1
D042000D1
D043000D1
0.3 B0.5/B0.9
0.3 B0.5/B1.8
0.3 B0.9/B1.8
0.3 B0.9/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
0.3 B1.8/B1.8
C100/C200
C200/C400
C300/C600
C150/C300
C200/C400
C400/C800
C400/C800
C400/C800
2.0/2.0
2.0/2.0
2.0/2.0
2.0/2.0
2.0/2.0
2.0/2.0
2.0/1.5
1.5/1.0
---------
---------
---------
---------
- Available in multi-ratio designs (full tap ratings same as single ratio above).
- 1 Second Thermal/Mechanical Rating: 80x full winding Inom / Unlimited mechanical.
* IC Approval (AE-1104) is noted by bold catalog number.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
19
15000 Volt
March 2008
20
LG(X)–15–6513 Current Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
COF(CXM)–110 Current Transformer
15000 Volt
Outdoor 15kV, 110kV BIL, Single, Dual & Multi Ratios
Oil-Filled, Wound Type, Metering/Relaying
March 2008
application
The COF(CXM)-110 outdoor current transformer is rated for use
on 15,000 volt systems with 110kV BIL. Primary current ratios are
available from 5:5 to 3000:5 at 60 Hertz (Hz) with a Rating Factor
of up to 4.0 (3200A max). This oil-filled current transformer will
operate with high accuracy for metering or relay applications.
mechanical description
The tank dome is fabricated from carbon or stainless steel,
depending on current rating. The units are pressure and vacuum
tight and hermetically sealed at the factory to prevent breathing
and oil contamination. Tank components are washed and coated
with anticorrosive iron phosphate and then finished with ANSI 70
Gray baked-on electrostatic polyester powder. The bushing is
ANSI 70 Gray, high strength porcelain with a high degree of stability
for transportation and seismic withstand. The primary terminals
are tin plated aluminum, NEMA 4-hole pads for units rated ≥400A
(copper for units rated ≥2000A) and NEMA 2-hole pads for units
rated <400A. A bypass protector is provided for all units rated
below 1200:5 to protect from transients. The secondary terminals
are #10 slotted screws on a short circuiting terminal block located
behind a removable cover in the CT base with three (3) 1 ½” NPT
conduit hubs. The ground terminal is a stainless steel NEMA 2hole pad. The unit is fitted with a pressure relief valve, oil level
gauge, and ½” drain valve.
accuracy performance
The COF-110 will operate with 0.3 Class accuracy for metering
applications with burdens of B0.1 to B1.8. The unit can be designed
with relay accuracy up to C800. The transformer is accurate
through its Rating Factor, and can be used continuously to this
level. The CXM-110 will operate with 0.15 Class high accuracy for
metering applications with burdens of B0.1 to B1.8. The transformer
maintains 0.15 Class accuracy from 0.5% of Inom through its Rating
Factor, and can be used continuously to this level.
mounting
The COF(CXM) is designed for mounting on substations structures
in an upright position with four mounting holes in the base.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Additional tests include dissipation and partial discharge tests.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 135% of the nominal system voltage.
options
The COF(CXM) is available with an Extra Creep Bushing, Polymer
Bushing, Stainless Steel Tank, 4kV Spark Gap and/or -50°C oil.
The unit can be offered in single, dual or multiple core designs.
Contact factory for other needs.
ORDERING INFO FOR COF-110
HIGH ACCURACY CXM-110
Ratio
Catalog
Number
Accuracy/
Burden
Rating
Factor
Catalog
Number
0.15 Accuracy
Range
Rating
Factor
5:5
10:5
D950005SA
D950010SA
0.3 B1.8
0.3 B1.8
1.5
1.5
D890005SA
D890010SA
0.025 to 20A
0.05 to 40A
4.0
4.0
…
…
…
…
…
…
…
150:5
200:5
D950150SA
D950200SA
0.3 B1.8
0.3 B1.8
1.5
1.5
D890150SA
D890200SA
0.75 to 600A
1 to 800A
4.0
4.0
…
…
…
D893000SA
15 to 3200A
1.07
5/10:5
10/20:5
D950010DA
D950020DA
0.3 B1.8/B1.8
0.3 B1.8/B1.8
2.0/1.5
2.0/1.5
---------
---------
---------
…
…
1.0
…
…
0.3 B1.8
…
…
D953000SA
…
…
3000:5
100/200:5
150/300:5
D950200DA
D950300DA
0.3 B1.8/B1.8
0.3 B1.8/B1.8
2.0/1.5
2.0/1.5
…
…
…
…
1000/2000:5
1500/3000:5
D952000DA
D953000DA
0.3 B1.8/B1.8
0.3 B1.8/B1.8
2.0/1.5
2.0/1.0
- Available in multi-ratio designs (full tap ratings same as single ratio above).
- 1 Second Thermal/Mechanical Rating: Single Ratio (150x lnom), Dual Ratio (75x full winding Inom), 144kA max.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
21
15000 Volt
March 2008
22
COF(CXM)–110 Current Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
KM–15–972 1 Ø Metering Unit
15000 Volt
Outdoor 15kV, °110kV BIL, Single Ratios
Molded Epoxy, Wound Type, 1Ø Metering
March 2008
application
The KM-15-972 outdoor, single phase metering unit is rated for
use on 5,000 & 15,000 volt systems with °110kV BIL. Primary
current ratios are available from 5:5 to 1200:5 at 60 Hertz (Hz)
with a Rating Factor of up to 3.0 (1200A max). Primary voltage
ratios are available from 20:1 to 70:1 for use on 5,000 & 15,000
volt, Grd Y systems. This dry-type, solid-cast metering unit will
operate with high accuracy for metering applications.
mechanical description
The core and coil assembly is wound and encapsulated in a high
dielectric strength epoxy resin to provide high withstand capabilities.
The external line to ground insulation consists of a cycloaliphatic
epoxy resin that provides excellent arc track properties in addition
to ultraviolet resistance and strong physical strength. A high voltage
stress ring around the top of the unit is supplied to control RIV
and partial discharge. The primary terminals are flat, tin-plated
copper with standard NEMA 2-hole pattern suitable for various
size conductors. The clamp-type post secondary terminals have
¼”-20 slotted screws and associated hardware located inside a
removable terminal box with two (2) 1” NPT conduit hubs and a
1” knockout on the bottom of the box.
accuracy performance
The KM-15-972 will operate, for the current transformer, with 0.3
Class accuracy for metering with burdens of B0.1 to B0.5. The CT
is accurate through its Rating Factor, and can be used continuously
to this level. The unit will operate, for the voltage transformer, with
0.3 Class accuracy for metering with burdens of 0, W, X, M and Y.
The VT is accurate from 90% to 110% of rated primary voltage.
mounting
The KM is designed for mounting on poles or substation structures
in an upright, underhung or cantilever position. The mounting
holes in the heavy galvanized steel plate are punched to industry
standard dimensions for interchangeability in the field.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 120% of the nominal system voltage.
options
A primary spark gap is available for capacitor bank or other
applications where high transients will be present. 90° angle
primary bus adapters can be supplied to place the two terminal
surfaces parallel to one another. Contact factory for other
needs.
ORDERING INFO FOR KM-15-972
HIGH ACCURACY N/A
Voltage
Ratings
Ratio* - 60:1
Pri*°:Sec - 7200:120
Current
Ratio
Catalog
Number**
Accuracy/
Burden
Rating
Factor
Catalog
Number*
Accuracy/
Burden
Rating
Factor
5:5
10:5
15:5
20:5
25:5
30:5
40:5
50:5
75:5
100:5
150:5
200:5
300:5
400:5
600:5
800:5
1000:5
1200:5
D9800505S060S
D9801005S060S
D9801505S060S
D9802005S060S
D9802505S060S
D9803005S060S
D9804005S060S
D9805005S060S
D9807505S060S
D9801015S060S
D9801515S060S
D9802015S060S
D9803015S060S
D9804015S060S
D9805015S060S
D9808015S060S
D9801025S060S
D9801225S060S
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.0
1.5
1.2
1.0
-------------------
-------------------
-------------------
Accuracy/Burden
0.3 0,W,X,M,Y 1.2 Z
Accuracy/Burden
--
- Thermal Burden Rating (Typical): 750VA. - Overvoltage Rating: 1.25x cont., 1.5x 30 sec.
- 1 Second Thermal/Mechanical Rating: 150x/300x Inom (100x/200x for 600:5, 75x/150x for above 600:5).
* Other Primary Voltage Ratings Available, contact factory.
° Units with less than 5kV primary voltage are rated 60kV BIL (catalog number will begin with “B”).
** IC Approval AE-1473 is noted by bold catalog number.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
23
15000 Volt
March 2008
24
KM–15–972 1 Ø Metering Unit
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
JS(JXM)–110 1Ø Metering Unit
15000 Volt
Outdoor 15kV, 110kV BIL, Single, Dual & Multi Ratios
Oil-Filled, Wound Type, 1Ø Metering
voltage. The JXM-110 will operate, for
the current transformer, with 0.15 Class
accuracy for metering with burdens of
B0.1 to B1.8. The CT maintains 0.15
Class accuracy from 0.5% of Inom through
its Rating Factor, and can be used
continuously to this level. The unit will
operate, for the voltage transformer, with
0.15 Class accuracy for metering with
burdens of 0, W, X, M, Y and Z, as well
as 0.3 ZZ. The VT is accurate from 90%
to 110% of rated primary voltage.
application
The JS(JXM)-110 outdoor single phase metering unit is rated
for use on 15,000 volt systems with 110kV BIL. Primary current
ratios are 5:5 to 1200:5 at 60 Hertz (Hz) with a Rating Factor of
up to 4.0 (1200A max). Primary voltage ratios are available from
20:1 to 70:1 for use on 5,000 & 15,000 volt, Grd Y systems. This
oil-filled metering unit will operate with high accuracy for metering
applications.
mechanical description
The tank is a standard distribution transformer tank made of heavy
gauge sheet steel with a seam welded bottom plate and a dome
shaped cover. The tank is washed and coated with anticorrosive
iron phosphate and then finished with an ANSI 70 Gray baked-on
electrostatic polyester powder. The primary bushings are ANSI
70 Gray, high strength porcelain with a tin plated bronze, NEMA
1-hole primary terminal. NEMA 4-hole primary terminals are
provided for units rated ≥200A. A bypass protector is provided
for all units rated below 1200:5 to protect from transients. A 5kV
H0 Bushing is included for power factor measurements and is
connected to the tank ground, a tin plated bronze eyebolt. The
secondary terminals consist of a feed thru block with ¼”-20 copper
studs and associated hardware located inside a removable terminal
box with three (3) 1 ½” NPT conduit hubs. The unit also includes
a pressure relief valve.
mounting
The JS(JXM) is designed for mounting
on poles or substation structures in
an upright position with ANSI type “A”
hanger brackets or optional mounting
feet. NOTE: Must be installed per NESC
electrical clearances.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Additional tests include dissipation and partial discharge tests.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 135% of the nominal system voltage.
accuracy performance
The JS-110 will operate, for the current transformer, with 0.3 Class
accuracy for metering with burdens of B0.1 to B1.8. The CT is
accurate through its Rating Factor, and can be used continuously
to this level. The unit will operate, for the voltage transformer, with
0.3 Class accuracy for metering with burdens of 0, W, X, M, Y, Z
and ZZ. The VT is accurate from 90% to 110% of rated primary
ORDERING INFO FOR JS-110
Ratio* - 60:1
Voltage
Ratings
Pri*:Sec - 7200:120
March 2008
options
The JS(JXM) is available with Lighting Arrestors, NEMA 4-hole
Primary Terminals, NEMA 2-hole Ground Pad, Mounting Feet,
Stainless Steel Tank, 4kV Spark Gap, Oil Level Indicator, Oil Drain
Valve, and/or -50°C oil. Contact factory for other needs.
Accuracy/Burden
0.3 0,W,X,M,Y,Z,ZZ
HIGH ACCURACY JXM-110
Accuracy/Burden
0.15 0,W,X,M,Y,Z, 0.3 ZZ
Current
Ratio
Catalog
Number
Accuracy/
Burden
Rating
Factor
Catalog
Number
0.15 B1.8
Acc Range
Rating
Factor
10:5
20:5
D80001S06EA
D80002S06EA
0.3 B1.8
0.3 B1.8
1.5
1.5
D79001S06EA
D79002S06EA
0.05 to 40A
0.1 to 80A
4.0
4.0
…
…
…
…
…
…
…
150:5
200:5
D80015S06EA
D80020S06EA
0.3 B1.8
0.3 B1.8
1.5
1.5
D79015S06EA
D79020S06EA
0.75 to 600A
1 to 800A
4.0
4.0
…
…
…
D79100S06EA
D79120S06EA
5 to 1200A
6 to 1200A
1.2
1.0
5/10:5
10/20:5
D80001D06EA
D80002D06EA
0.3 B1.8/B1.8
0.3 B1.8/B1.8
2.0/1.5
2.0/1.5
------
------
------
…
…
1.2
1.0
…
…
0.3 B1.8
0.3 B1.8
…
…
D80100S06EA
D80120S06EA
…
…
1000:5
1200:5
500/1000:5
600/1200:5
D80100D06EA
D80120D06EA
0.3 B1.8/B1.8
0.3 B1.8/B1.8
2.0/1.2
2.0/1.0
- Available in multi-ratio designs.
- Thermal Burden Rating (Typical): 4000VA.
- Overvoltage Rating: 1.1x cont., 1.9x 8 hours.
- 1 Second Thermal/Mechanical Rating: Single Ratio (150x lnom), Dual Ratio (75x full winding Inom), 144kA max.
* Other Primary Voltage Ratings Available, contact factory.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
25
15000 Volt
March 2008
26
JS(JXM)–110 1Ø Metering Unit
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
MVCT(MXM)–110 3 Ø Metering Unit
15000 Volt
Outdoor 15kV, 110kV BIL, Single, Dual & Multi Ratios
Oil-Filled, Wound Type, 3Ø Metering
March 2008
transformers, with 0.15 Class
high accuracy for metering
applications with burdens of
B0.1 to B1.8. The transformer
maintains 0.15 Class accuracy
from 0.5% of Inom through its
Rating Factor, and can be
used continuously to this
level. The unit will operate,
for the voltage transformers,
with 0.15 Class accuracy for
metering with burdens of 0,
W, X, M, Y and Z, as well as
0.3 ZZ. The VT’s are accurate
from 90% to 110% of rated
primary voltage.
application
The MVCT(MXM)-110 outdoor three phase metering unit is rated
for use on 15,000 volt systems with 110kV BIL. Primary current
ratios are 5:5 to 1200:5 for 60 Hertz (Hz) with a Rating Factor of
up to 4.0 (1200A max). Primary voltage ratios are available from
20:1 to 120:1 for use on 5,000 & 15,000 volt systems. This oilfilled metering unit will operate with high accuracy for 2, 2 ½ or 3
element metering applications.
mechanical description
The unit is built of heavy walled steel construction similar to
proven distribution and small power transformer construction and
is strongly braced to withstand both electrical and mechanical
stresses. The tank is washed and coated with anticorrosive iron
phosphate and then finished with an ANSI 70 Gray baked-on
electrostatic polyester powder. The primary bushings are ANSI 70
Gray, high strength porcelain with tin plated bronze, NEMA 4-hole
primary terminals. The secondary terminals consist of a feed thru
block with ¼”-20 copper studs and associated hardware located
inside a terminal box with three (3) 1 ½” NPT conduit hubs. The
ground terminal is a stainless steel NEMA 2-hole pad. The unit
includes a pressure relief valve, CT by-pass protectors, 5kV H0
Bushing (for 3P 4W designs), ½” oil drain valve, and a magnetic
type oil level gauge which is easily read from a distance.
mounting
The MVCT(MXM) is designed for overhead mounting on poles
or substation structures in an upright position with ANSI type “C”
hanger brackets or four mounting holes in the base. NOTE: Must
be installed per NESC electrical clearances.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Additional tests include dissipation and partial discharge tests.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 135% of the nominal system voltage.
accuracy performance
The MVCT-110 will operate, for the current transformers, with 0.3
Class accuracy for metering with burdens of B0.1 to B1.8. The
CT’s are accurate through their Rating Factor, and can be used
continuously to this level. The unit will operate, for the voltage
transformers, with 0.3 Class accuracy for metering with burdens of options
0, W, X, M, Y, Z and ZZ. The VT’s are accurate from 90% to 110% The MVCT(MXM) is available with a Stainless Steel Tank, 4kV
of rated primary voltage. The MXM-110 will operate, for the current Spark Gaps and/or -50°C oil. Contact factory for other needs.
ORDERING INFO FOR MVCT-110
HIGH ACCURACY MXM-110
Voltage
Ratings
Ratio* - 60:1
Pri*:Sec - 7200:120
Current
Ratio
Catalog Number
(3P 4W)**
Accuracy/
Burden
Rating
Factor
Catalog Number
(3P 4W)
0.15 B1.8
Acc Range
Rating
Factor
10:5
20:5
D88001S06CA
D88002S06CA
0.3 B1.8
0.3 B1.8
1.5
1.5
D86001S06CA
D86002S06CA
0.05 to 40A
0.1 to 80A
4.0
4.0
Accuracy/Burden
0.3 0,W,X,M,Y,Z,ZZ
Accuracy/Burden
0.15 0,W,X,M,Y,Z, 0.3 ZZ
…
…
…
…
…
…
…
150:5
200:5
D88015S06CA
D88020S06CA
0.3 B1.8
0.3 B1.8
1.5
1.5
D86015S06CA
D86020S06CA
0.75 to 600A
1 to 800A
4.0
4.0
…
…
…
D86100S06CA
D86120S06CA
5 to 1200A
6 to 1200A
1.2
1.0
5/10:5
10/20:5
D88001D06CA
D88002D06CA
0.3 B1.8/B1.8
0.3 B1.8/B1.8
2.0/1.5
2.0/1.5
------
------
------
…
…
1.2
1.0
…
…
0.3 B1.8
0.3 B1.8
…
…
D88100S06CA
D88120S06CA
…
…
1000:5
1200:5
500/1000:5
600/1200:5
D88100D06CA
D88120D06CA
0.3 B1.8/B1.8
0.3 B1.8/B1.8
2.0/1.2
2.0/1.0
- Available in multi-ratio designs.
- Thermal Burden Rating (Typical): 6000VA (2000VA/phase). - Overvoltage Rating: 1.1x cont., 1.9x 8 hours (3P 4W).
- 1 Second Thermal/Mechanical Rating: Single Ratio (150x lnom), Dual Ratio (75x full winding Inom), 144kA max.
* Other Primary Voltage Ratings Available, contact factory. ** For 3P 3W, change catalog digits “88” to “87”.
- IC Approval AE-0753 Rev. 2 noted by bold catalog number (also 50/100:5 and 150/300:5 ratios).
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
27
15000 Volt
March 2008
28
MVCT(MXM)–110 3 Ø Metering Unit
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
ME–015 3 Ø Metering Rack
Outdoor 15kV, °110kV BIL, Single & Dual Ratios
Pre-Wired, Molded Epoxy CTs & VTs, 3Ø Metering
15000 Volt
March 2008
application
The ME-015 outdoor, three phase metering rack is rated for use on
5,000 & 15,000 volt systems with °110kV BIL. Current transformers
have ratios available from 5:5 to 1200:5 for 60 Hertz (Hz) with a
Rating Factor of up to 3.0 (1200A max). Voltage transformers have
ratios available from 20:1 to 120:1 for use on 5,000 & 15,000 volt
systems. This metering rack will operate with high accuracy for
1, 2, 2 ½ or 3 element metering applications.
mechanical description
The rack is made of lightweight aluminum and incorporates the
BB-15-971 or BB-15-972 current transformers mounted vertically
and the PTT-110-977(G) or PTT-110-9710(G) voltage transformers
mounted horizontally. The CT primary terminals are flat, tin-plated
copper with standard NEMA 2-hole pattern suitable for various
size conductors. The VT primary terminals are M12 stud with a
compression type lug for #8 - #2 AWG conductors. The secondary
terminals are pre-wired through protective conduit to a 10 position testing
The units are individually tested per the IEEE C57.13 standard,
test switch in standard red/black colors mounted to the rack.
including applied and induced voltage, accuracy and polarity. An
additional partial discharge test is performed to guarantee the units
accuracy performance
The ME-015 will operate, for the current transformers, with 0.3 are free of partial discharge through 120% of the nominal system
Class accuracy for metering with burdens of B0.1 up to B1.8. The voltage. The secondary pre-wiring is tested for correct polarity and
CT’s are accurate through their Rating Factor, and can be used type of transformer to minimize damage due to misconnection.
continuously to this level. The rack will operate, for the voltage
transformers, with 0.3 Class accuracy for metering with burdens options
of 0, W, X, M, Y and up to Z. The VT’s are accurate from 90% to The ME rack is available with a 35’ S/O outdoor cable extension to
a test switch/meter socket, a pre-programmed GE type KV2C Form
110% of rated primary voltage.
9S meter, and/or Canadian color-code or other color scheme wiring.
CT’s and/or VT’s are available with 0.15 Class high accuracy.
mounting
The ME rack is designed for mounting on poles in an upright Transformers can be mounted with the VT’s vertical and CT’s
position. There are two galvanized steel mounting bolts supplied horizontal, or rack can be designed with only VT’s or only CT’s.
Contact factory for other needs.
to attach to the pole.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
29
15000 Volt
March 2008
30
ME–015 3 Ø Metering Rack
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
MK–15 3 Ø Metering Rack
Outdoor 15kV, °110kV BIL, Single Ratios
Pre-Wired, Molded Epoxy CT/VTs, 3Ø Metering
15000 Volt
March 2008
application
The MK-15 outdoor, three phase metering rack is rated for use
on 5,000 & 15,000 volt systems with °110kV BIL. Primary current
ratios are available from 5:5 to 1200:5 for 60 Hertz (Hz) with a
Rating Factor of up to 3.0 (1200A max). Primary voltage ratios are
available from 20:1 to 70:1 for use on 5,000 & 15,000 volt, Grd Y
systems. This metering rack will operate with high accuracy for
1, 2 or 3 element metering applications.
mechanical description
The rack is made of lightweight aluminum and incorporates the KM15-972 metering units mounted either vertically or horizontally. The
primary terminals are flat, tin-plated copper with standard NEMA
2-hole pattern suitable for various size conductors. The secondary
terminals are pre-wired through protective conduit to a 10 position
test switch in standard red/black colors mounted to the rack.
accuracy performance
The MK-15 will operate, for the current transformers, with 0.3
Class accuracy for metering with burdens of B0.1 to B0.5. The
CT’s are accurate through their Rating Factor, and can be used
continuously to this level. The rack will operate, for the voltage
transformers, with 0.3 Class accuracy for metering with burdens
of 0, W, X, M and Y. The VT’s are accurate from 90% to 110% of
rated primary voltage.
mounting
The MK rack is designed for mounting on poles in an upright
position. There are two galvanized steel mounting bolts supplied
to attach to the pole.
testing
The units are individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity. An
additional partial discharge test is performed to guarantee the units
are free of partial discharge through 120% of the nominal system
voltage. The secondary pre-wiring is tested for correct polarity and
type of transformer to minimize damage due to misconnection.
options
The MK rack is available with a 35’ S/O outdoor cable extension
to a test switch/meter socket, a pre-programmed GE type KV2C
Form 9S meter, and/or Canadian color-code or other color scheme
wiring. Contact factory for other needs.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
31
15000 Volt
March 2008
32
MK–15 3 Ø Metering Rack
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
MP–015 3 Ø Metering Cubicle
Outdoor 15kV, °110kV BIL, Single & Dual Ratios
Pre-Wired, Molded Epoxy CTs & VTs, 3Ø Metering
15000 Volt
March 2008
application
The MP-015 outdoor, three phase metering, pad-mounted cubicle
is rated for use on 5,000 & 15,000 volt systems with °110kV BIL
and also complies with ANSI C57.12.28. Current transformers
have ratios available from 5:5 to 1200:5 for 60 Hertz (Hz) with a
Rating Factor of up to 3.0 (1200A max). Voltage transformers have
ratios available from 20:1 to 120:1 for use on 5,000 & 15,000 volt
systems. This metering cubicle will operate with high accuracy for
1, 2, 2 ½ or 3 element metering applications.
mechanical description
The cubicle is made of #12 AWG mild steel with Munsell Green
#7GY 3.29/1.5 powder finish and incorporates the BB-15-971
or BB-15-972 current transformers and the PTT-110-977(G) or
PTT-110-9710(G) voltage transformers. The cubicle doors are
pad-lockable with three point latch and a penta-head bolt and
have screened vents on the transformer side. White GPO-3
glass reinforced polyester barriers are built-in between phases
and the live side. The primary connections can be radial or loop
feed with one or two load taps. The connections can be either
200A loadbreak bushing wells or 600A non-loadbreak inserts, both
are ANSI/IEEE 386 compliant. The secondary terminals are prewired to a 10 position test switch and 9S meter socket in standard
red/black colors on the outside right wall when facing the elbow
side of the cubicle.
accuracy performance
The MP-015 will operate, for the current transformers, with 0.3
Class accuracy for metering with burdens of B0.1 up to B1.8. The
CT’s are accurate through their Rating Factor, and can be used
continuously to this level. The cubicle will operate, for the voltage
transformers, with 0.3 Class accuracy for metering with burdens
of 0, W, X, M, Y and up to Z. The VT’s are accurate from 90% to
110% of rated primary voltage.
mounting
The MP cubicle is designed for pad-mount use.
testing
The transformer units are individually tested per the IEEE C57.13
standard, including applied and induced voltage, accuracy and
polarity. An additional partial discharge test is performed to
guarantee the units are free of partial discharge through 120% of
the nominal system voltage. The secondary pre-wiring is tested
for correct polarity and type of transformer to minimize damage
due to misconnection.
options
The MP cubicle is available with the test switch on the inside wall
of the cubicle to allow wiring to a remote meter socket. Unit is also
available with only CT’s or VT’s. Canadian color-code or other color
scheme wiring can be provided. CT’s and/or VT’s are available with
0.15 Class high accuracy. Contact factory for other needs.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
33
15000 Volt
March 2008
34
MP–015 3 Ø Metering Cubicle
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
U/VCD–17(H) Voltage Transformer
Indoor 15kV, 95kV BIL, Single & Dual Ratios
Molded Epoxy, Wound Type, Metering/Relaying
15000 Volt
March 2008
application
The U/VCD-17(H) indoor voltage transformer is rated for use on
15,000 volt systems with 95kV BIL. Primary voltage ratios are
available from 60:1 to 120:1 for use on 15,000 volt systems, at
60 Hertz (Hz). This dry-type, solid-cast voltage transformer will
operate with high accuracy for metering or relay applications.
mechanical description
The core and coil assembly is wound and encapsulated in a
high dielectric strength epoxy resin to provide high withstand
capabilities. The primary terminal(s) are screw-type, tin-plated, for
#12 to #8 AWG conductors. The secondary terminals are ¼”-20
slotted screws and associated hardware embedded in epoxy resin
on the front side of the transformer. In addition, a ground terminal
is provided near the secondary terminals on the base plate.
accuracy performance
The U/VCD-17 will operate with 0.3 Class accuracy for metering
and relay applications with burdens of 0, W, X, M, Y and Z. The
transformer is accurate from 90% to 110% of rated primary voltage.
The U/VCD-17H will operate with 0.15 Class high accuracy for
metering applications with burdens of 0, W, X, M and Y. The
transformer is accurate from 90% to 110% of rated primary
voltage.
mounting
The U/VCD is designed for mounting inside switchgear or
other indoor applications in an upright, underhung or cantilever
position.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 120% of the nominal system voltage.
options
Units are available in single or double bushing models. The
VCD-17H high accuracy voltage transformer is only available in
the double bushing model. Primary terminal(s) can be equipped
with fuse clip(s) and fuse(s). The unit can be offered in switchgear
format with primary terminal(s) toward the back. Contact factory
for other needs.
ORDERING INFO FOR U/VCD-17
Ratio
Primary
Secondary
60:1
63.5:1
70:1
100:1
110:1
120:1
7200
7620
8400
12000
13200
14400
120
120
120
120
120
120
HIGH ACCURACY VCD-17H
Catalog Number
1 Bushing
2 Bushing
D916G060S0
D916G063S0
D916G070S0
----
D916060S0
D916063S0
D916070S0
D916100S0
D916110S0
D916120S0
Accuracy/
Burden
Catalog Number
2 Bushing Only
Accuracy/
Burden
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
0.3 0,W,X,M,Y,Z
D916060E0
D916063E0
D916070E0
D916100E0
D916110E0
D916120E0
0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
0.15 0,W,X,M,Y
- Thermal Burden Rating (Typical): Std Acc. (1500VA), High Acc. (1000VA).
- Overvoltage Rating: 1.1x cont.
- For fuse clips, add a “C” per clip needed at the end of the catalog.
- For fuses, add an “F” per fuse needed at the end of the catalog.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
35
15000 Volt
March 2008
36
U/VCD–17(H) Voltage Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
CID–17(H) Current Transformer
Indoor 15kV, 95kV BIL, Single & Dual Ratios
Molded Epoxy, Wound Type, Metering/Relaying
15000 Volt
March 2008
application
The CID-17(H) indoor current transformer is rated for use on 15,000
volt systems with 95kV BIL. Primary current ratios are available
from 5:5 to 1200:5 at 60 Hertz (Hz) with a Rating Factor of up to
1.5. This dry-type, solid-cast current transformer will operate with
high accuracy for metering or relay applications.
mechanical description
The core and coil assembly is wound and encapsulated in a
high dielectric strength epoxy resin to provide high withstand
capabilities. The primary terminals are flat, tin-plated copper with
standard NEMA 2-hole pattern suitable for various size conductors.
The clamp-type post secondary terminals have ¼”-20 slotted
screws and associated hardware embedded in epoxy resin on the
front side of the transformer. The ground terminal is provided near
the secondary terminals on the base plate.
accuracy performance
The CID-17 will operate with 0.3 Class accuracy for metering with
burdens of B0.1 to B1.8 and C200 for relay applications. The
transformer is accurate through its Rating Factor, and can be
used continuously to this level. The CID-17H will operate with
0.15 Class high accuracy for metering applications with burdens
of B0.1 to B0.5. The transformer maintains 0.15 accuracy from
10% (0.3 accuracy from 2%) of Inom through its Rating Factor, and
can be used continuously to this level.
mounting
The CID is designed for mounting inside switchgear or other indoor
applications in an upright, underhung or cantilever position.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 120% of the nominal system voltage.
options
Contact factory for other needs.
ORDERING INFO FOR CID-17
Ratio
Catalog
Number
5:5
10:5
D9150005S0
D9150010S0
HIGH ACCURACY CID-17H
Accuracy/Burden
Metering
Relay
0.3 B1.8
0.3 B1.8
C200
C200
Rating
Factor
Catalog
Number
Accuracy/
Burden
Rating
Factor
1.5
1.5
D9150005E0
D9150010E0
0.15 B0.5
0.15 B0.5
1.5
1.5
…
…
…
…
…
…
…
…
50:5
75:5
100:5
D9150050S0
D9150075S0
D9150100S0
0.3 B1.8
0.3 B1.8
0.3 B1.8
C200
C200
C200
1.5
1.5
1.5
D9150050E0
D9150075E0
D9150100E0
0.15 B0.5
0.15 B0.5
0.15 B0.5
1.5
1.5
1.5
…
…
…
…
…
…
…
…
600:5
800:5
1000:5
1200:5
D9150600S0
D9150800S0
D9151000S0
D9151200S0
0.3 B1.8
0.3 B1.8
0.3 B1.8
0.3 B1.8
C200
C200
C200
C200
1.5
1.1
1.1
1.1
D9150600E0
D9150800E0
D9151000E0
D9151200E0
0.15 B0.5
0.15 B0.5
0.15 B0.5
0.15 B0.5
1.5
1.1
1.1
1.1
5/10:5
10/20:5
D9150005D0
D9150010D0
0.3 B0.5/B1.8
0.3 B0.5/B1.8
C100/C200
C100/C200
2.0/1.5
2.0/1.5
D9150005F0
D9150010F0
0.15 B0.2/B0.5
0.15 B0.2/B0.5
2.0/1.5
2.0/1.5
…
…
…
…
…
…
…
…
300/600:5
400/800:5
500/1000:5
600/1200:5
D9150300D0
D9150400D0
D9150500D0
D9150600D0
0.3 B0.5/B1.8
0.3 B0.5/B1.8
0.3 B0.5/B1.8
0.3 B0.5/B1.8
C100/C200
C100/C200
C100/C200
C100/C200
2.0/1.5
1.1/1.1
1.1/1.1
1.1/1.1
D9150300F0
D9150400F0
D9150500F0
D9150600F0
0.15 B0.2/B0.5
0.15 B0.2/B0.5
0.15 B0.2/B0.5
0.15 B0.2/B0.5
2.0/1.5
1.1/1.1
1.1/1.1
1.1/1.1
- 1 Second Thermal/Mech Rating Min: 90x/240x Inom (66kA/178kA for above 600:5 & 300/600:5). Contact factory for actuals.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
37
15000 Volt
March 2008
38
CID–17(H) Current Transformer
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
KCB–17 1 Ø Metering Unit
15000 Volt
Indoor 15kV, °95kV BIL, Single Ratios
Molded Epoxy, Wound Type, 1Ø Metering
March 2008
application
The KCB-17 indoor, dead-front, single phase metering unit is rated
for use on 5,000 & 15,000 volt systems with °95kV BIL. Primary
current ratios are available from 5:5 to 200:5 at 60 Hertz (Hz) with a
Rating Factor of up to 3.0. Primary voltage ratios are available for
20:1 to 70:1 for use on 5,000 & 15,000 volt, Grd Y systems. This
dry-type, solid-cast metering unit will operate with high accuracy
for metering applications.
mechanical description
The core and coil assembly is wound and encapsulated in a high
dielectric strength epoxy resin to provide high withstand capabilities.
The entire surface of the transformer is coated with a conductive
layer that is intended to be solidly grounded when energized. This
allows for compact mounting inside switchgear or enclosures.
The primary terminals are standard 200 Ampere rated dead-front
bushing well construction and can be connected using industry
standard inserts and elbow connectors. The secondary terminals
are ¼”-20 slotted screws with flat and lock washers located inside
a metallic terminal cover with two (2) 1” NPT conduit hubs, one
sealed and one left open for conduit entrance. The ground terminal
is provided inside the terminal cover along with a manually operated
CT secondary shorting device for safety purposes.
accuracy performance
The KCB-17 will operate, for the current transformer, with 0.3 Class
accuracy for metering with burdens of B0.1 to B0.5. The CT is
accurate through its Rating Factor, and can be used continuously
to this level. The unit will operate, for the voltage transformer, with
0.3 Class accuracy for metering with burdens of 0, W, X, M and Y.
The VT is accurate from 90% to 110% of rated primary voltage.
mounting
The KCB is designed for mounting inside switchgear, pad-mounted
enclosures, or vault applications.
testing
The unit is individually tested per the IEEE C57.13 standard,
including applied and induced voltage, accuracy and polarity.
Partial discharge testing is performed to guarantee the unit is free of
partial discharge through 120% of the nominal system voltage.
options
Unit is also available as a CT or VT only. Contact factory for other
needs.
ORDERING INFO FOR KCB-17
HIGH ACCURACY N/A
Voltage
Ratings
Ratio* - 60:1
Pri*°:Sec - 7200:120
Current
Ratio
Catalog
Number
Accuracy/
Burden
Rating
Factor
Catalog
Number*
Accuracy/
Burden
Rating
Factor
5:5
10:5
15:5
20:5
25:5
30:5
40:5
50:5
75:5
100:5
150:5
200:5
D9900505S060S
D9901005S060S
D9901505S060S
D9902005S060S
D9902505S060S
D9903005S060S
D9904005S060S
D9905005S060S
D9907505S060S
D9901015S060S
D9901515S060S
D9902015S060S
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
0.3 B0.5
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.67
2.0
1.33
1.0
-------------
-------------
-------------
Accuracy/Burden
0.3 0,W,X,M,Y 1.2 Z
Accuracy/Burden
--
- Thermal Burden Rating (Typical): 750VA.
- Overvoltage Rating: 1.1x cont.
- 1 Second Thermal/Mechanical Rating: 100x/270x Inom.
* Other Primary Voltage Ratings Available, contact factory.
° Units with less than 5kV primary voltage are rated 60kV BIL (catalog number will begin with “B”).
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
39
15000 Volt
March 2008
40
KCB–17 1 Ø Metering Unit
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
MI–15 3 Ø Metering Cubicle
Outdoor 15kV, °95kV BIL, Single Ratios
Pre-Wired, Molded Epoxy CT/VTs, 3Ø Metering
15000 Volt
March 2008
application
The MI-15 outdoor, three phase metering, pad-mounted cubicle
is rated for use on 15,000 volt systems with °95kV BIL and also
complies with ANSI C57.12.28. Current transformers have
ratios available from 5:5 to 200:5 for 60 Hertz (Hz) with a Rating
Factor of up to 3.0 (200A max). Voltage transformers have ratios
available for 20:1 to 70:1 for use on 5,000 & 15,000 volt, Grd Y
systems. This metering cubicle will operate with high accuracy
for 1, 2 or 3 element metering applications.
mechanical description
The cubicle is made of #12 AWG stainless steel with Munsell
Green #7GY 3.29/1.5 powder finish and incorporates the KCB-17
metering units. The cubicle doors are pad-lockable with a three
point latch and a penta-head bolt and have screened vents on the
removable transformer side door. The primary connections are
radial with one load tap (loop feed configuration may be available
by use of feed-through inserts). The connections are 200A
loadbreak bushing wells, which are ANSI/IEEE 386 compliant.
The secondary terminals are pre-wired to a 10 position test switch testing
and 9S meter socket in standard red/black colors on the outside The transformer units are individually tested per the IEEE C57.13
right wall when facing the elbow side of the cubicle.
standard, including applied and induced voltage, accuracy and
polarity. An additional partial discharge test is performed to
accuracy performance
guarantee the units are free of partial discharge through 120% of
The MI-15 will operate, for the current transformers, with 0.3 the nominal system voltage. The secondary pre-wiring is tested
Class accuracy for metering with burdens of B0.1 to B0.5 The for correct polarity and type of transformer to minimize damage
CT’s are accurate through their Rating Factor, and can be used due to misconnection.
continuously to this level. The cubicle will operate, for the voltage
transformers, with 0.3 Class accuracy for metering with burdens options
of 0, W, X, M and Y. The VT’s are accurate from 90% to 110% of The MI cubicle is available with a terminal block on the inside
rated primary voltage.
wall of the cubicle to allow wiring to a remote meter socket. Unit
is also available with only CT’s or VT’s. Canadian color-code or
mounting
other color scheme wiring can be provided. Contact factory for
The MI cubicle is designed for pad-mount use.
other needs.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage
41
15000 Volt
March 2008
42
MI–15 3 Ø Metering Cubicle
NOTE: OUTLINES ARE FOR REFERENCE ONLY. CONTACT FACTORY FOR ACTUAL DESIGN DRAWINGS.
Dry type: 3022 NC 43 North • Pinetops, NC 27864 • Phone: +1 252 827-3212 • www.abb.com/mediumvoltage
Oil type: 101 Kuhlman Blvd • Versailles, Kentucky 40383 • Phone: +1 859 879-2999 • www.abb.com/highvoltage