Conwin’s Archline Dispenser Pack
Item #36050
Instructions
100 Pack
Conwin #32400
Conwin Balloon Tying Discs
The Fast and Easy Way to Tie Balloons!
Benefits:
• Increase productivity by attaching ribbon and tying balloon.
• Prevent sore fingers from hand-tying balloons.
• Designed for use with latex balloons up to 16 inches.
Discs available in convenient 100 packs and 1000 packs.
1
1. lace the Archline in the dispenser pack
with the line feeding from the base of the
spool(s).
2. Attach the Line Tensioner approximately 6
inches from the end of the line. Push the red
button on the Line Tensioner to expose the
metal hook on the top of the ball. Thread
the Archline under the hook and release the
button to capture the line. The Line Tensioner will prevent the Archline from
free spinning inside the pack when balloons are attached to the line.
3. Feed the Archline through the grommets in the lid and close the Velcro® flap.
Pull the Archline to remove any slack inside the pack.
2
Conwin’s Archlines
Hold the inflated balloon in your left
hand. With your right hand, pinch the
neck of the balloon and the ribbon
together and stretch both around the
end of the tying post.
Feed curling ribbon through ribbon guide hole located under
tying post. Place the balloon disc
on tying post.
4
3
Hold the stretched balloon neck and
ribbon together in your left hand.
Place your fingers behind the tying
disc and slide the disc over the neck of
the balloon.
Slide tying disc down approximately
one inch on the neck of the balloon.
Remove tied balloon from post and
cut the ribbon on the convenient ribbon cutter.
Grips balloons securely and is unaffected by temperature. Will
not stretch. Easier to work with than fishing line.
Available in 50# and 150# test.
Conwin’s Masterpiece Series Videos
These exciting instructional videos feature the industry's top balloon artists sharing their secrets of the
trade on everything from the latest decorating techniques to business management and marketing skills.
Conwin’s Black Belt
Item #36120
Visit ConwinOnline.com to see complete descriptions
of the 12 programs in the series.
Service & Warranty
For assistance with service & repair
issues, or for warranty information,
please visit ConwinOnline.com,
or call (818)246.9233
Visit www.ConwinOnline.com today!
CONWIN, Inc.
4510 Sperry Street • Los Angeles, CA 90039
Phone (818) 246-9233 • FAX (818) 246-6862
This innovative apron was
designed and field tested
by twisters and decorators.
The unique and efficient
Velcro straps on the sides
of the Black Belt can hold
up to 1000 entertainer
balloons for easy access.
The Black Belt features 12
specialty pockets enabling
you to have your tools
right at your fingertips. The Black Belt is made out of heavy-duty
nylon woven fabric with reinforced stitching and features an
adjustable belt that fits all sizes.
Conwin’s Grip-It Balloon
Holder
Item #32190
Instructions
1
3
2
3-Pocket Balloon Caddy
Conwin #32020
LA
BA
LL
TE
1. Clamp the Grip-It
Balloon Holder to
any convenient
counter top.
OO N TE M P
2. Slide the ribbon
sideways into the
spring coil.
3. Half twist the ribbon and press it firmly into the spring coil.
This insures firm
spring grip on ribbon.
Conwin’s Grip Guide
Balloon Template
Instructions Item #32090
Conwin’s Balloon Caddy provides an instant workstation around the
cylinder. Three-Pocket Caddy holds balloons, weights, ribbon, discs, etc.
Durable mesh pockets.
1. Wrap Velcro® belt around cylinder
and insert belt through buckle.
2. Position pockets around cylinder.
Tighten and fasten Velcro® belt.
1. Place the ruled Template Strip on the
edge of a table or work counter.
2. Press the black release button on Grip
Guide to fully open the clamp. Position
the open clamp with the brass tube
pointing upward directly over the "0"
measure on the Template Strip. Firmly
squeeze the clamp to securely attach it to
the countertop. Slide the brass upright
into the tube and adjust until it is perpendicular to the countertop.
3. Repeat step #2,
attaching the 2nd clamp
to the desired setting on
the Template Strip. To
change the size setting,
press the black release
button on the clamp and
reposition the clamp to
the desired setting.
4. For best results, pull
the slightly over-inflated
balloon toward you
through the two uprights.
As you pull the balloon,
slowly release the air
until the balloon just
passes between the two
uprights.
032906
3. Fill pockets with Balloons,
Weights, Tying Discs, etc.
Grip-Strips
The strips grip the ribbon while
you are on the job or at the
shop. The adhesive backing
allows for convenient placement on any clean surface.
Item #32070
Grip-Tabs
Ideal for centerpieces, simply
stick the Grip-Tabs to any
clean surface and tie on the
balloons. Super Grip-Tabs are
also available for larger
boquets.
Item #32190