Plastic Cement
Wet or Dry Surfaces
Description
CR-25 is a wet or dry surfaces asbestos free plastic cement. It is formulated with asphalt
and fibers for multipurpose applications. It stops leaks and repairs deteriorated areas, fill
holes and cracks on foundations, asphalt roofs, shingles, vent, chimney joints and
others. Once dried, it becomes a strong waterproofed coating and resists against bad
weather. Can be use to glue back asphalt shingles and protect them from wind.
Surface Preparation
Surfaces must be structurally sound, clean, free of frost, dust, rust, chipped paint, oil,
grease and any loose or deteriorated materials.
Application
Apply with a putty knife, a trowel or by hand with gloves. To fill, joints and cracks, push
profoundly into gaps making bulge out on surface to avoid accumulation of water. Repair
cracks, holes by applying a coat of 3 mm (1/8'') thick to the defective sections and
overtake of 150 mm (6'') around the repairs. To glue back shingles, apply only 3 points
of 25 mm (1'') evenly distributed. To facilitate low temperature applications, keep
product in a warm place.
Cleanning
Clean tools and equipment with mineral spirits.
Norm
CAN/O.N.G.C. 37.5M-89
Package
Available in 310 ml and 800 ml tube , and 1 kg, 4 kg, 12 kg and 20 kg pail.
Shelf Life
12 months after purchasing date when kept in its tightly closed original container. Condor Chimiques Inc.
2645 B, Terra-Jet, St-Cyrille-de-Wendover, Québec, J1Z 1B3
www.condor.pro
[email protected]
Phone.: 819-474-6661
Fax.: 819-474-6681
CR-25
Plastic Cement
CR-25
Wet or Dry Surfaces
Warning
Technical Data Table
Specifications
Color
Black
Solids by Volume
70 - 80 %
Weight
1,21 kg/L (10,1 pounds/gal)
Coverage
0,32 m²/kg (3,45 ft²/kg) for 3 mm (1/8'')
coat
Dry Time*
at 50 % H.R. 20°C (68°F)
To the Touch*
4 hours
Completely Dry*
48 hours
Service Temperature
Maximum : 85°C (185°F) Dry coating
Application Temperature
10°C or more
Chemical Resistance
Resistant to water calcium chloride, salt
and to lightly acid or alkaline
solutions. Do not resist to oils, greases
and solvents.
Permeance to Water Vapor (ASTM E96)
3 mm (1/8'') coat before drying 2.9
ng/Pa.m2.s (0.05 perms)
MAY CAUSE IRRITATION.
CONTENT MAY CATCH FIRE.
COMBUSTION DANGER
FIRST AID: Skin contact : Wash skin
immediately with soap and water.
Eye contact : Flush immediately with
plenty of water for at least 15 minutes,
lifting upper and lower eyelids. Consult
a physician.
Clothes contact : Remove contaminated
clothes.
Inhalation : Move the victim to fresh air.
Consult a physician if necessary.
Ingestion : DO NOT INDUCE VOMITING.
Give milk if conscious. Keep victim
warm and call immediately a physician.
KEEP OUT OF REACH OF CHILDREN.
READ SAFETY DATA SHEET BEFORE
USING THIS PRODUCT
* Drying Time depend of surface porosity and temperature.
Restriction
If product is applied near a ventillation unit of or an air conditioner, take necessary
precautions to avoid infiltration solvent odor inside. Protect freshly applied product
and open container from open flame and adjacent welding activity. For EXTERIOR
USE only.
Warranty
The customer shall verify of the suitability of this product for the intended purpose.
Applicator's skill, weather and surface conditions being beyond manufacturer's
control, we limit our liability to replacement of defective material only in sealed
container, within 1 year of proof of purchase. FOB plant.
Condor Chimiques Inc.
2645 B, Terra-Jet, St-Cyrille-de-Wendover, Québec, J1Z 1B3
www.condor.pro
[email protected]
Phone.: 819-474-6661
Fax.: 819-474-6681
Powered by TCPDF (www.tcpdf.org)