HOTEMP  PLUS
High-temperature chain oil
@@1001= HOTEMP PLUS@1002= 5.160@1003= 09.1995@1004= product information@
1005= e@1006= CD "PI A-Z"@@
Description
operating conditions. At temperatures above 180 °C the approximate
HOTEMP PLUS
HOTEMP PLUS is a synthetic highconsumption is 1.5 to 2 ml of oil per
temperature chain oil for textile and
meter of chain and operating shift.
● Efficient lubrication at high
plastic processing machines enWe recommend lubricating chain
operating temperatures
suring reliable operation at high
rails continuously or at least once a
temperatures and loads.
● Good regenerating effect on
day, depending on their length and
the used oil
It has good penetration properties
design. Weekly relubrication is often
and rapidly forms a lubricating film.
sufficient for chain pins with an oil
● Favourable viscositydepot. However, it is better to apply
Owing its special additive combinatemperature behaviour, thus
an exactly metered oil quantity every
tion, HOTEMP PLUS is very resisensuring safe cold starts
day than to relubricate too late or to
tant to pressure and wear. Special
over-lubricate, especially at high
● Good penetration properties
adhesion improvers prevent the oil
and rapid formation of a
from being thrown off the lubrication chain speeds.
lubricating film
Chains with a spray lubrication
point.
system
should
be
lubricated
with
HOTEMP PLUS is very efficient
● Good adhesion, is not
against the adhesion of finishing and very small oil quantities once per
thrown off
softening compounds as well as con- shift or on a daily basis to keep
densates. The few residues resulting them covered with an oil film.
● Resistant to wear and pressure
from its synthetic components can
● Low formation of residues
be easily regenerated by adding
Storage
owing to fully synthetic
fresh oil.
constituents
The storage period is approx.
3 years if the product is stored in
● Efficient against the adhesion
Application
the original closed container in a
of finishing and softenting
dry place.
agents as well as condensates
HOTEMP PLUS is suitable for all oillubricated stenter chains, e.g.
Pack sizes
– roller chains
– chains or clips supported by ball
5 l canister
bearings (combined lubrication of
20 l canister
bearings, chain joints and slide200 l drum
ways)
– sliding chains (lubrication of
sliding rails, chain joints and bolts)
in equalizing frames, single-layer
stenters, tier stenters, festoon driers Product data
and steamers as well as coating
Colour, aspect
green, clear
installations.
fully synthetic
Base
Density, DIN 51 757 at 20 °C, g/ml
approx. 0.95
Application notes
Kinematic viscosity, DIN 51 561
approx. 1200
at 20 °C, mm 2/s
HOTEMP PLUS can be applied with
at 40 °C, mm 2/s
approx. 320
all pumps, spraying or metering
at 100 °C, mm 2/s
approx. 28
equipment.
Viscosity index, DIN ISO 2909, VI
approx. 110
Lubrication intervals and lubricant
> 220
Flash point, DIN ISO 2592 (open cup), °C
quantities depend on the chain
Service temperature range, °C
to approx. 250
design, type of lubrication and
Product Information 5.160 e
Edition 09.95, replaces edition 07.94
446.III.94
HOTEMP PLUS
Material Safety Data Sheet
Section I
Section V – Health Hazard Data
Manufacturer's name: Klüber Lubrication München KG
Chemical name and synonyms: Lubricating oil
Trade name and synonyms: HOTEMP PLUS
Chemical family: Ester oil, synthetic hydrocarbon oil
Formula:
Proprietary
Threshold limit value: n/a
Effects of overexposure:
Eyes: Mild irritation
Skin: Mild irritation, may cause dermititis, oil acne or
folliculitis with repeated contact.
Ingestion: No more than slightly toxic if swallowed.
Inhalation: n/a
Emergency and first aid procedures:
Eyes: Flush with large amount of water.
Skin: Remove contaminated clothing, wash skin with soap
and water, launder clothing prior to reuse.
Ingestion: Contact doctor for directions. Never give anything by mouth to an unconscious person.
Section II – Hazardous Ingredients
Paints, preservatives, solvents
%
Pigments
–
Catalyst
–
Vehicle
–
Solvents
–
Additives
–
Others
–
Alloys and metallic coatings
%
Base metal
–
Alloys
–
Metallic coatings
–
Filler metal plus coating or core flux –
Others
–
TLV (units)
–
–
–
–
–
–
TLV (units)
–
–
–
–
–
Hazardous mixtures of other liquids, solids, or gases
––
Section III – Physical Data
Boiling point:
n/a
Vapor pressure (mm Hg):
n/a
Vapor density (air=1):
n/a
Solubility in water:
not soluble
Specific gravity (H 2O=1):
approx. 0.95
Percent, volatile by volume (%): 0
Evaporation rate (………=1):
n/a
Appearance and odor: green, clear, neutral
Section IV – Fire and Explosion Hazard Data
Flash point (method used): > 220 °C
ASTM D-92
Flammable limits: ––
Lel:
Uel:
Extinguishing media: water fog, foam, dry chemical, CO2
Special fire fighting procedures: Use self-contained
breathing apparatus, cool fire exposed areas and
equipment.
Unusual fire and explosion hazards: Do not use direct
stream of water, material may float and reignite.
n/a = not applicable
Section VI – Reactivity Data
Stability: stable
Incompatibility (materials to avoid): Strong oxidizing
materials, such as pure oxygen.
Hazardous decomposition products: n/a
Hazardous polymerization: will not occur
Section VII – Spill or Leak Procedures
Steps to be taken in case material is released or spilled:
Eliminate all sources of ignition. Recover free liquid. Add
absorbent to spill area. Collect absorbent. Keep product
out of waterways.
Waste disposal method:
Incinerate absorbed material or dispose of it in accordance
with your local, state and federal regulations.
Section VIII – Special Protection Information
Respiratory protection (specify type):
Ventilation:
Local exhaust:
Protective gloves:
Eye protection:
Other protective equipment:
n/a
n/a
recommended
n/a
n/a
no
Section IX – Special Precautions
Precautions to be taken in handling and storing:
Minimize skin contact with all lubricants. Wash with soap
and water prior to eating, drinking, smoking or using
sanitary facilities.
Other precautions:
All chemical products should be handled as to prevent
constant or repeated contact.
The data in this brochure is based on our general experience and knowledge at the time of printing and is intended to give information of possible applications to a
reader with technical experience without, however, constituting an assurance of properties for specific cases.
We recommend contacting our Technical Consulting Staff for information regarding specific applications. If required and possible we will be pleased to provide a
sample for testing.
Klüber Lubrication, a member of the Freudenberg group of companies
Publisher and Copyright:
Klüber Lubrication München KG
Reprints, total or in part, are permitted if source
is indicated and voucher copy is forwarded.
Klüber Lubrication München KG
Postfach 701047, D-81310 München
Tel. (089) 7876-0, Telex 5 23 131, Telefax (089) 7876333