Two alarms indicator
1/8 DIN - 96 x 48
J1 line
Q u i c k G u i d e • Ι STR-FJ1ENG02
Declaration of Conformity and Manual retrieval
Description and dimensions
J1 is panel mounting, Class II instrument. It has been designed
with compliance to the European Directives.
All information about the controller use can be found in the User
Manual: MIU_J1_EN.pdf.
The Declaration of Conformity and the manual of the controller
can be downloaded (free of charge) from the web-site:
www.ascontecnologic.com
Once connected to the web-site, search:
J1
then click on J1 from the result list.
In the lower part of the product page (in any language) is present
the download area with links to the documents available for the
controller (in the available languages).
Depth: 110 mm
Electrical connections
IN1 Input value
(engineering units)
J1
Menu access
Min./Max. values display
Alarm
acknowledge
Alarm
status LEDs
Selection/
value confirmation
Thermocouple
Panel cut out and mounting
1
 Warning!
Model Code
Configuration Code
The product code indicates the specific hardware configuration of
the instrument, that can be modified by specialized engineers only.
A 4 + 2 digits index code follows the model (letters from I... P). This
code must be set to configure the controller. Using UP ( ) and DOWN
( ) keys insert the desired configuration code. When not configured the 1st part of the code is 9999.
Line
Model: J 1
Basic
Accessories
Configuration
2nd part
1st part
Line
J
Power supply
Input type and range
I
L
TR Pt100 IEC751
-99.9…300.0°C -99.9…572.0°F
0
0
1
TR Pt100 IEC751
-200…600°C
-328…1112°F
0
1
A
TC L Fe-Const DIN43710
0…600°C
32…1112°F
0
2
A B C 0 - 0 9 0 0 / I L M 0 - O P 0 0
100...240Vac (-15...+10%)
3
TCJ Fe-Cu45% Ni IEC584
0…600°C
32…1112°F
0
3
24Vac (-25...+12%) or 24Vdc (-15....+25%)
5
TC T Cu-CuNi
-200 …400°C
-328…752°F
0
4
Outputs OP1 - OP2
B
TC K Chromel-Alumel IEC584
0…1200°C
32…2192°F
0
5
None
0
TC S Pt10%Rh-Pt IEC584
0…1600°C
32…2912°F
0
6
Relay - Relay
7
TC R Pt13%Rh-Pt IEC584
0…1600°C
32…2912°F
0
7
Serial Communications
C
None
0
RS485 Modbus/Jbus SLAVE
5
TC B Pt30%Rh Pt6%Rh IEC584
0…1800°C
32…3272°F
0
8
TC N Nichrosil-Nisil IEC584
0…1200°C
32…2192°F
0
9
TC E Ni10%Cr-CuNi IEC584
0…600°C
32…1112°F
1
0
TC NI-NiMo18%
0…1100°C
32…2012°F
1
1
TC W3%Re-W25%Re
0…2000°C
32…3632°F
1
2
TC W5%Re-W26%Re
0…2000°C
32…3632°F
1
3
Dc input 0…50mV linear
Engineering and units
1
4
Dc input 10…50mV linear
Engineering and units
1
5
1
6
Custom input and range [1]
Pt100
External
shunt 2.5Ω
mA
- Whenever a failure or a malfunction of the device may cause
dangerous situations for persons, things or animals, please
remember that the plant must be equipped with additional
devices which will guarantee safety.
- We warrant that the products will be free from defects in
material and workmanship for 18 months from the date of
delivery. Products and components that are subject to wear
due to conditions of use, service life and misuse are not covered
by this warranty.
viale Indipendenza 56, 27029 - Vigevano (PV)
Tel.: +39 0381 698 71, Fax: +39 0381 698 730
internet site: www.ascontecnologic.com
E-mail:
[email protected]
mV
2
Terminals
Ø
L
2
1
Display mode
M
Green
0
Red
1
Red when alarm 1 (AL1) active
2
O
Alarm type and function
Stripped wire
L: 5.5 mm 0.21 in.
Fork-shape
AMP165004
Ø 5.5 mm - 0.21 in.
Pin connector
1.4 mm 0.055 in. max.
q
P
AL1 AL2
Non-active
0
Sensor break alarm
1
Active High
Absolute
Deviation
Band
2
Active Low
3
Active High
4
Active Low
5
Active Out
6
Active In
7
Rate alarm (AL1 only)
8
-
[1] For instance, other thermocouples types, custom linearisation etc.
Indicator configuration chart
Parameter list
The present chart includes only the basic parameters
For the list and the description of all the indicatorparameters see the User Manual.
When the indicator is new and not configured shows the code Conf at power ON. In this case NO PASSWORD is needed to configure
the instrument (see the grey box in the chart below). Enter the configuration code in accordance with the desired functional
characteristics.
The parameters pointed out with grey background are those necessary to configure the options and are NOT shown in the configuration
chart. All the parameters are fully described and explained in the user manual of the controller.
If the parameter Code has previously set to a value ≥5000, (for example 5033 in the chart) the indicator is
locked in operator mode; insert the correct password to access both the parameter and the configuration menus.
Operator mode
5033
pAss
Password Entry
Only if Code
value ≥5000
1274. 8
Code
Parameter Name
1st Configuration
Value
Default
Alarm parameters
Al.par
Al. sp
Configuration
Al.1sp
AL1 alarm
threshold
Al.1Op
AL1 alarm
output
Al.1hy
AL1
hysteresis
Al.2Op
AL2 alarm
output
Al.2sp
AL2 alarm
threshold
Op.1a
AL1 alarm
action
Al.2hy
AL2
hysteresis
Op.1a
AL2 alarm
action
Al.ref
Alarm internal
reference value
(engineering unit)
Al.1lb
AL1 Latching/
blocking
Configuration code
digits O - P
Al.2lb
AL2 Latching/
blocking
Engineering units
(see table 2)
pAss
Only if Code
value <5000
(33 factory default)
Must be equal to the
value of the parameter
Code
[3]
Configuration code
digits I - L - M - N
If linear scales are
choosen, set also the
following 5 parameters
Number
of decimals
Low range
High range
IN1 square root
Notes: [2] Cut off the square root of the
input value enables the user
to round to zero a result that is
too low to be important.
[3] A not configured indicator
shows Conf at power ON:
the configuration procedure
is shown in the grey box.
[4] The controller shows pass after conf: using the keys S
and G insert the password to
configure the controller.
Table 1 Engineering Units
Value
C
f
none
mU
U
mA
A
bar
psI
rh
ph
Description
degree Celsius
degree Fahrenheit
none
mV
Volt
mA
Ampére
Bar
PSI
Rh
pH
IN1 square root
result cut-off [2]
IN1 filter
time constant
IN1 input shift
New password
(33 factory default)
Value
Default
Code Password
33
0000
AL.1SP AL1 alarm Threshold
0
Unit Engineering units
NONE
AL.1Hy AL1 Alarm Hysteresis
0
in.1dd IN1 decimal point
O
AL.2SP AL2 alarm Threshold
0
in.1Lo IN1 low range for engineering units
O
AL.2Hy AL2 Alarm Hysteresis
0
in.1Hi IN1 high range for engineering units
9999
AL.reF Alarm reference source (eng. units)
0
tFiL.1 IN1 filter time constant
Password Entry [4]
Parameter Name
9999
code
Cut1 IN1 square root result cut-off
Conf
Code
Con.2 2nd Configuration code
Con.1
in.1Cn IN1 square root
Alarm set
User
in.1Sh IN1 input shift
AL.1OP AL1 alarm output
OP1
AL.2OP AL2 alarm output
OP2
OP.1a AL1 alarm action
Direct
Direct
Prot Communications protocol
JBUS
OP.2A AL2 alarm action
baud Baud rate
9600
AL.1lb AL1 alarm latching/blocking
0
1
AL.2lb AL2 alarm latching/blocking
0
Addr Indirizzo seriale dell’indicatore
User