ADVANTAGES
USGBC LEED, EQ Credit 4.2 AND 4.3: Low-emitting
VOC Compliant Materials
No noxious odors
0 VOC’s - 100% solids
Meets USDA criteria
Non-Blushing
RECOMMENDED USES
Low temperature applications
Concrete/Masonry
NOTE: Read the information contained in the Product Information
Bulletins prior to starting any project.
Read MSDS for health and safety information.
Products are for professional use only.
SURFACE PREPARATION
Surface preparation is the essential first stage treatment of a substrate
before the application of any coating. The performance of a coating is
significantly influenced by its ability to adhere properly to the substrate
material. It is generally established that correct surface preparation is
the most important factor affecting the total success of surface treatment.
Surfaces will be clean, dry, and sound, the presence of even small
amounts of surface contaminants, dust, efflorescence, laitance, salts,
curing compounds, dirt, oil, form release agents, and other foreign matter
can physically impair and prevent coating adhesion to the substrate.
MIXING PROCEDURES
Mix entire/full package containers, do not measure or mix partial
containers of multi-component materials.
Blend 2 parts-A with 1 part-B by volume into a clean container.
Adequately blend FreedomTuff ® 6130-LT for 3 to 4 minutes at a slow
speed using a drill motor and paddle until the mixture is consistent
making sure not to encapsulate any air.
If necessary add up to 1 quart (0.9463 liters) of acetone per 3 gallon
(11.356 liters) kit as permitted by local regulations, remix product
immediately, carefully scraping the sides and bottom of the pail during
mixing.
After mixing thoroughly, immediately pour the FreedomTuff ® 6130-LT
onto the horizontal surface and spread evenly over the entire surface
using trowel or squeegee and back roll.
APPLICATION
Application temperature should be between 40º F (4.44° C) and 95º F
(35° C). Insure that the outside temperature is at least 6º (-14.44) above
the dew point and rising, for best results apply while the outside
temperature is descending.
After mixing thoroughly, immediately pour the FreedomTuff ® 6130-LT
onto the horizontal surface and spread evenly over the entire surface
using trowel or squeegee and back roll, do not puddle.
Concrete should be shot blasted to a CSP 4-6.
Do not apply more primer to the substrate than can be coated within (18)
eighteen hours of set time.
Grinding is only permitted in areas that are inaccessible to shot blasting
equipment.
FreedomTuff ® 6130-LT will require mechanical abrasion once it
exceeds (18) eighteen hours.
Concrete should be cured for a minimum of 28 days prior to product
application and have at least 3000 psi compressive and 220 psi tensile
strength.
Apply coating to FreedomTuff ® 6130-LT when surface is dry to the
touch.
PACKAGING 2:1 RATIO
1½ Gallon Kit: (1 gallon/3.785 liters part-A) and (½ gallon/1.892 liters
part-B).
3 Gallon Kit: (2 gallon/7.570 liters part-A) and (1 gallon/3.785 liters partB).
COLOR
Clear - Due to its chemical composition, FreedomTuff ® 6130-LT will
discolor.
COVERAGE RATE
100 to 300 square feet per gallon (9.29030m² to 27.8709m² per liter),
applied at a theoretical 5 mils per coat (0.127mm) do not puddle.
Coverage rates are approximate and vary based on type of substrate,
porosity, roughness, size of broadcast aggregate.
Working time for FreedomTuff ® 6130-LT is approximately 20 minutes.
If two (2) coats of primer are required, prime the entire surface with the
first coat at a rate of 1 gallon (3.78 liters) per 300 square feet (27.8709
m²). Apply the second coat at a rate of 1 gallon (3.78 liters) per 400
square feet per gallon (37.1612 m²) and some systems require a
broadcast of dry contamination free 30 mesh sand (595 microns,
0.2320”, 0.595 millimeters) into the second coat of wet primer until the
primer is fully filled approximately .25 lb. (0.1 kg) per square foot
(0.092903m²).
Excess aggregate must be completely removed before application of the
coating.
SPECIFICATION AND FIELD ASSISTANCE
Contact Freedom ® Chemical Corporation for assistance.
FREEDOMTUFF ® 6130-LT EPOXY PRIMER
FreedomTuff ® 6130-LT is a 100% solids, plural component, low temperature epoxy primer.
Jobsite visits by Freedom ® Chemical Corporation’s employees or its
independent agents are solely for the purpose of determining
qualification for warranty.
DISPOSAL
Spilled material, unused contents and empty containers must be
disposed of in accordance with local, state and federal regulations.
Excess moisture vapor in concrete slabs may result in primer and/or
coating to delaminate, discolor or cause improper curing.
Freedom ® Chemical Corporation assumes no liability for substrate
defects.
Substrates that have previously been coated are subject to absorption,
which may affect the adhesion of a new coating.
STORAGE
FreedomTuff ® 6130-LT has a shelf life of 1 year from the date of
manufacture, in factory-sealed containers.
High/Low temperatures and humidity can significantly affect pot life and
extend the cure time.
Never store directly on concrete surface, always store on pallets.
FreedomTuff ® 6130-LT is not UV Stable.
Avoid freezing temperatures.
TESTING
Perform an adhesion test prior to starting any coating project.
Rotate stock regularly.
Do not open until ready to use and keep containers sealed tightly.
LIMITATIONS
The end user should check the suitability of this product prior to its
application.
WARNING
FreedomTuff ® 6130-LT contains Epoxy Resins.
Caution this product becomes flammable with addition of acetone.
FREEDOMTUFF ® 6130-LT TYPICAL PROPERTIES
MIX RATIO BY VOLUME
N/A
N/A
N/A
2A:1B
GEL TIME (150G MASS) @ 77º F (25º C)
SET TIME @ 77º F (25º C)
DRY TIME @ 77º F (25º C)
N/A
3:15 (H:MIN)
SET TIME @ 40º F (4.44º C)
N/A
6:45 (H:MIN)
DRY TIME @ 40º F (4.44º C)
N/A
15:10 (H:MIN)
PENCIL HARDNESS
N/A
2H
PERSOZ HARDNESS
N/A
167 SECONDS
IMPACT RESISTANCE
N/A
42/0 IN LB
HARDNESS: SHORE D
ASTM D-2240
70
TENSILE STRENGTH
ASTM D-695
4200 PSI
VISCOSITY AT 77°F (25°C)
N/A
COMBINED PART A AND PART B 380 CPS
VOLATILE ORGANIC COMPOUNDS
ASTM D-3960
0 LB/GALLON, 0 GRAMS/LITER
DRY FILM THICKNESS PER COAT
N/A
5 MILS/0.127MM
ADHESION (DRY CONCRETE)
ASTM D-4541
>800 PSI
COMPRESSIVE STRENGTH
ASTM D-695
12000 PSI
9 MINUTES
2:50 (H:MIN)
Incredible Stuff, Exceptional Service, and Friendly People™
Read all the information in this product information bulletin, and material safety data sheet (MSDS) before applying any material. The information contained herein is for purposes of identifying the product and does not constitute a warranty that the product will conform to this
description. Product specifications and performance will vary depending on application methodologies, raw materials and other factors. Guidelines, recommendations, statements, and information contained herein is based on tests we believe to be reliable and correct, but
accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty, either expressed or implied. It is the user’s responsibility to satisfy themselves, by their own information and tests, to determine suitability of the product for their own
intended use, application and job situation and t he user assumes all risk and liability resulting from t heir own use of the product. We do not suggest or guarantee that any hazards listed herein are the only ones that may exist. Neither seller nor manufacturer shall be
liable to the buyer or any third party for any inj ury, loss or damage directly or indirectly resulting from use of, or inability to use, the product. Recommendations or statements, whether verbal or in writing, other than those contained herein shall not be binding upon the manufacturer,
unless in writing and signed by a corporate officer of Freedom ® Chemical Corporation. Typical properties and application information is provided for the purpose of establishing a general profile of the material and proper application procedures. Performance results were
obtained in a controlled environment and Freedom ® Chemical Corporation makes no claim that these tests or any other tests accurately represent all environments. Products manufactured by Freedom ® Chemical Corporation are free of defects for a period of one (1) year,
liability and buyer’s remedy under this limited warranty shall not exceed the purchase price of the materials in question. † Freedom ® Chemical and FreedomTuff ® are trademarks registered in the US Patent and Trademark Office. † The marks of Freedom ® Chemical Corporation,
its divisions, slogans, emblems, other marks appearing in this document are the trademarks and/or service marks of Freedom ® Chemical Corporation, its subsidiaries, affiliates or licensors Copyright © March 2015 Freedom ® Chemical Corporation. All Rights Reserved. All
published information is subject to change without notice.
FREEDOM ® CHEMICAL CORPORATION 14056 ARTESIA BLVD., CERRITOS, CA 90703 • (562) 343-9697 • GEORGIA (678) 259-9283 • REV 4/15