English
46302 - 10/15 GlucoMen areo_Quick guide - EN
Quick Guide
upplied with the meter.
D SE-205 12 Malmö
agnostics.se
How to use the sampler
GlucoJect Dual PLUS
CAUTION! NEVER use sampler on more than one person. Take a new lancet for each sampling and
do not leave a used lancet in the sampler.
1. Wash hands or
4. Pull out the sliding
®
the alternative site
(AST). Unscrew the
sampler’s tip by turning it counterclockwise.
Error codes and m
sleeve to lock the sampler. Press and hold the
sampler against your
finger and press the
trigger.
5. Press the lancet ejec-
2. Insert a new
sterile lancet into
the lancet holder and
push it fully.
tor with your thumb
while pulling out the
sliding sleeve for disposing of the used
lancet.
System error hardware. Remove and insert the batteries again and repeat the
test with a new test strip. If error code persists, please contact customer service.
ER 2
Test strip is damaged or used, or have the blood sample applied before
”blood drop symbol” began to flash on the screen. Repeat the test
with a new strip.
Er 3
Test strip was given the small amount of blood. Stick again to repeat
the test with a new test strip and the right amount of blood.
Er 4
Test strip was removed or dislodged during the countdown. Repeat
the test with a new test strip.
Er 5
HI
LO
NFC was disconnected during transmission. Repeat the NFC-transfer.
If the problem persists, contact customer service.
Your test result is higher than 33,3 mmol/L!
Your test result is lower than 1,1 mmol/L!
CAUTION! If HI or LO appears, contact your health care provider before
changing your treatment. Shown HI or LO repeatedly even though your
blood sugar levels are high or low, contact customer service.
Test strip is damaged
”blood drop symbol
with a new strip.
Er 3
Test strip was given
the test with a new t
Er 4
Test strip was remov
the test with a new t
Er 5
HI
LO
NFC was disconnect
If the problem persis
Your test result is hig
Your test result is low
NOTE! This is a concise quick
Error codes and messages
ER 1
ER 2
Customer Service:
Place the sampler on the
skin at selected plug area.
Press and hold for a few
seconds, then press the
shutter release button
to take a blood test.
depth by rotating the
tip. 1-2 for soft or thin
skin, 3 for normal skin,
4-5 for thick or hardened skin.
System error hardware
test with a new test stri
CAUTION! If HI or LO
changing your treatm
blood sugar levels a
Sampling AST
3. Adjust the puncture
ER 1
Quick Gu
46302 - 10/15 GlucoMen areo_Quick guide - EN
er on more than one persampling and
e sampler.
Blood glucose measurement with wireless transmission
Customer Service: 040-32 12 70 [email protected]
NOTE! This is a concise quick reference guide. Detailed information can be found in the manual supplied with the meter.
Medeon Science Park Per Albin Hanssons väg 41, hus D SE-205 12 Malmö
Tel 040–32 12 70 Fax 040–32 12 71 www.menarinidiagnostics.se
Blood glucose mea
How you measure your blood sugar.
How to set the t
Time and date are preset, please check that this is correct the first time you use
the meter.
The opening
of the test
1. Check that the meter
2. Press
4 seconds
3. Press or to scrol
various menus.
4. Use or to select
next step: year, mont
5. After confirming the
the Setup menu.
Contact Area
How to manage t
1. Wash hands with soap and water.
2. Take a new test strip from the bottle and replace the cap immediately.
3. Place the sole of the test strip that has a metallic contact surface, into
the meter opening.
4. The meter shows a blinking blood drop and is now ready for measurement.
5. Stick with the sampler.
6. Put the blood drop against the short side of the stick that absorbs the right
amount of blood. A beep sounds and countdown starts on the display.
7. Read the test results. A beep sounds (if enabled) when the result is
displayed on the screen.
8. Press the eject button to eject the used test strip. The meter turns off
automatically.
3.
Your meter stores up to
1. Make sure the meter
2. Press
for 2 second
3. The latest test results
4. Press
or
to scro
5. Press
for more th
6.
How to select a measured value.
1. When your test result appears, press until the selection symbols
starts flashing. With the arrow keys (
), select the desired mark
(before meal),
(after meal),
(training) or
(general).
2. Confirm your selection by pressing the
button. You can select
multiple selections (but only when you select the
or
),
repeat steps 1 and 2.
g
View average results fo
1. Press
for 2 secon
is displayed on the sc
2. Continue to press
90 days.
3. Press
for more tha
How to set the time and date.
Wireless transmiss
1. Check that the meter is off. (If not, press
for 3 seconds)
2. Press
4 seconds to enter the setting menu.
3. Press or to scroll the setup menus and press
to access the
various menus.
4. Use or to select the value. Press
to confirm and go to the
next step: year, month, day, time format, hour, minute.
5. After confirming the minutes (by pressing ) will return to
the Setup menu.
Your saved test results can
a smartphone) with an NFC
The first time, you must tu
setup menus) by pressing
confirm and leave.
1. Activate the NFC-transfe
2. Place your meter close t
3. The meter starts automa
on the screen).
4. When the data transfer i
along with the symbol
5. Press the
button for 3
Test Strip Port
Button for
On/Off/Enter
How to manage the measurement results in memory.
a
Your meter stores up to 730 results with date, time and marks.
1. Make sure the meter is off. (If not, press
for 3 seconds).
2. Press
for 2 seconds to start (”mem” appears on the screen).
3. The latest test results with the time, date and selections are shown.
4. Press
or
to scroll to the memory.
5. Press
for more than 3 seconds to turn off the meter.
How to replace th
View average results for the 1, 7, 14, 30, 60 or 90 days.
1. Press
for 2 seconds to turn on the meter. Press
again (”AVG”
is displayed on the screen). The meter shows the day’s average.
2. Continue to press
to display the average for 1, 7, 14, 30, 60 or
90 days.
3. Press
for more than 3 seconds to turn off the meter.
Buttons
Up/Down
Wireless transmission via NFC (Near Field Communication)
Test Strip Port
ter
Your saved test results can be transferred to an NFC-enabled device (such as
a smartphone) with an NFC-compatible application installed (eg GlucoLog).
The first time, you must turn on your meter NFC function (found in the
setup menus) by pressing the
or
to select ON or OFF. Press
to
confirm and leave.
1. Activate the NFC-transfer in the app in your smartphone.
2. Place your meter close to your smartphone (<1 cm).
3. The meter starts automatically and the data is transferred (
flashes
on the screen).
4. When the data transfer is completed, ”End” appears on the screen
along with the symbol
, and a beep sounds.
5. Press the
button for 3 seconds to turn off the meter.
Eject button
Antenna (NFC)
How to replace the battery in GlucoMen® Areo.
Buttons
Up/Down
The meter is powered by two CR2032 3V batteries. When the symbol
low
battery is lit, it is time to change. You do not have to set the date and time if you
insert the new batteries within 2 minutes after the old is removed. How to use:
1. Make sure the meter is off.
2. Open the battery cover on the back of the meter and remove the batteries.
3. Insert the new batteries in the battery holder with the ”+”- side up.
4. Close the battery cover.
Battery Cover
Data Transfer
Port
The meter is powered by tw
battery is lit, it is time to cha
insert the new batteries with
1. Make sure the meter is o
2. Open the battery cover o
3. Insert the new batteries
4. Close the battery cover.