Tools and Hardware
Catalog Data
CA325009EN
Effective March 2016
Supersedes 325-23 January 2011
COOPER POWER
SERIES
Wire clips, grips and grounding lugs
Non-static ground wire clips
Ground wire clips
Eaton eliminates a major source of radio and
television interference with its Cooper Power™
series inexpensive non-static ground wire clips.
They prevent trouble-causing air gaps and static
discharges by permanently maintaining a high
pressure contact between the clip and the ground
wire. Installation is simple; drive the clip into the
wood until the clip is firmly seated, then insert the
ground wire under the clip finger. Continue driving
until the finger protrudes through the slot in the
body of the clip. Then bend the body over the
ground wire and into the wood.
Eaton securely fastens ground wires to poles and
crossarms with its Cooper Power series easyto-install clips. Make high pressure, large area
contact with the ground wire and prevent radio
interference producing static discharges by using
ground wire clips. Ground wire clips are quickly
installed by driving one nail and then bending the
tail back over the nail head. Copperweld nails are
recommended for copper clips.
Guy wire clips
To secure guy wire strands quickly, use Eaton's
Cooper Power™ series Kearney™ guy wire clips.
They do the job in a fraction of the time compared
to using a guy wire strand and leave no protruding
ends. They are pre-shaped and easily closed with
pliers.
T-bolt grounding lugs
Eaton connects ground wires to transformers
or steel structures with its Cooper Power series
heavy-duty lugs. The threaded stud fits all standard
transformer tapped grounding pads. A high
clamping force prevents the wire from pulling
out. The wire may be run 90° from the position
illustrated.
Shown above left to right are ground wire clips,
guy wire clips, ground wire clips and nails, and
T-bolt grounding lugs.
Catalog Data CA325009EN
Wire clips, grips and grounding lugs
Effective March 2016
Rust cutter
Table 1. Ground Wire Clip Ordering Information
Eaton's Cooper Power series Kearney™ rust cutter loosens rusted or
corroded nuts and bolts in seconds. This saves time, labor and the
inconvenience of sawing off corroded fastenings. Rust cutter spray
reaches otherwise inaccessible rusted areas. This product contains
no fluorocarbons and is harmless to the skin. It is packed in 5 ounce
pressurized cans.
Material
Dimensions
(Inches)
Ground Wire
Maximum Size
Catalog Number
Bronze
.625 x 2.5
4 Str.
12325
Bronze
.625 x 2.875
1/0 Str.
12325-1
Zinc-Plated Steel
.625 x 2.5
4 Str.
12326
Steel
.625 x 2.875
1/0 Str.
12326-1
Table 2. Guy Wire Clip Ordering information
Strand Size
(Inches)
Catalog Number
Aluminum
Plated Steel
.3125
36
336CPS
.3750
37
337CPS
.4375
38CPS
338CPS
Table 3. Ground Wire Clip Ordering Information
Figure 1. Rust cutter.
Ground Wire Material
Maximum Size
Catalog Number
Zinc-Plated Steel
4 Sol.
5730
Copper
4 Sol.
5730-1
Aluminum
4 Sol.
5730-2
Copperweld Nails
8d–2.5" x .0625"
–
64110-41
Table 4. T-Bolt Ground Lug Ordering Information
Material
Stud Size
WireSize
Catalog Number
Plated Bronze
1/2"-13 x 3/8"
6 Sol.
to 1 Str.
17546-2
Table 5. Rust Cutter Ordering Information
Quantity
Catalog Number
Case of 24 cans
19229-1
NNote: Sold by case only.
Eaton
1000 Eaton Boulevard
Cleveland, OH 44122
United States
Eaton.com
Eaton’s Cooper Power Systems Division
2300 Badger Drive
Waukesha, WI 53188
United States
Eaton.com/cooperpowerseries
© 2016 Eaton
All Rights Reserved
Printed in USA
Publication No. CA325009EN
Eaton is a registered trademark.
All other trademarks are property
of their respective owners.
For Eaton's Cooper Power series product
information call 1-877-277-4636 or visit:
www.eaton.com/cooperpowerseries.