D
RIFTW
BROW
OOD
N
ED
TINT
W AT
ING
age
me
n Dam ick Dr y Ti
u
Q
Su
s from r
t
c
e
t
ro
Colo
fs & P
Wood
l
rproo
u
e
f
i
t
t
a
W
Beau
Adds
ONE U.S. GALLON 3.785 LITERS
OOF
ERPR
O do r r
L ow
ate
a nd W
SoapCleanup
CAUTION! KEEP OUT OF REACH OF CHILDREN.
Read Other Cautions on Back Panel.
J4603
What is Armor All ® Wood Protector?
Armor All® Waterproofing Wood Protector is a water-based, acrylic liquid sealer that will waterproof and protect wood from UV sun damage. This durable pigmented
sealer will change the existing color of wood, imparting a warm, rich color to your wood surface and help to minimize the effect of UV damage and graying of wood. Armor
All® Waterproofing Wood Protector far exceeds industry specifications (ASTM D4446) for protecting wood from water damage. It will not harm surrounding vegetation.
Helpful Tips: This product is intended for exterior use on wood surfaces only. Avoid contact with
surfaces not intended to be treated. May be applied to pressure treated wood. Allow new pressure
Surface Preparation
treated wood to weather for at least 60 days before applying sealer. Do not use as an additive to
1. For untreated wood: Use Armor All™ E-Z Deck Wash® to brighten old weathered wood and paint or stain. Do not mix with any other product. Do not apply over previously painted or stained
surfaces unless old finish is removed or completely weathered away. Surface and air temperature
remove any contaminants such as mildew, dust, dirt, oil and grease.
should be above 50˚F during application and drying. Do not use when rain is expected within 24
2. For severely weathered wood, or wood previously treated with a sealer: Use a pressure
hours. Test in an inconspicuous area to ensure you are satisfied with the appearance, as the color
washer with Armor All™ E-Z Deck Wash® to strip away the top layer.
will vary depending on wood type and age.To avoid overspray when using a pump-up sprayer,
3. Allow surface to dry 2 days before applying sealer. Test for dryness by sprinkling drops of spray the deck floor and inside of railings first. Then either brush the outside of rails, or cover the
water onto the wood surface. If dry and unsealed, wood will readily absorb water.
deck floor and spray the outside of rails. For even color, don't stop once you start applying.
Application:
Do
not take internally. Prolonged contact with skin may cause irritation.
1. Protect hands with chemical-resistant gloves and eyes with chemical splash goggles.
FIRST AID – IF SWALLOWED, call your poison control center, hospital emergency
Protect adjacent surfaces, such as vinyl siding.
room or physician immediately. IN CASE OF EYE CONTACT, immediately flush
2. Pour half the contents of the bottle into a can, roller pan or pump-up sprayer.
with water, remove any contact lens, continue flushing with water for at least 15
3. Replace cap on bottle and shake well. Add remaining product to can, pan or sprayer.
minutes. If irritation persists, get medical attention. FOR SKIN CONTACT, wash
Intermix multiple cans to ensure even color.
with soap and water. If irritation persists, get medical attention. WARNING: This
4. Apply using a synthetic paint brush, paint roller or pump-up tank sprayer. Apply evenly,
product contains chemicals known to the State of California to cause cancer and
coating the length of a board in the direction of the wood grain. Maintain a wet edge by
reproductive harm.
working small areas at a time to prevent lap marks. Do not allow sealer to pool on the
KEEP OUT OF REACH OF CHILDREN - MAX V.O.C. 100 grams per liter
surface. Brush or roll out after 15 minutes as needed. One coat will provide sufficient
For assistance call:
protection.
the Barr Help Line. 800-398-3892
Product Number GAWB60542
Monday thru Friday
5. Allow to dry for at least 24 hours before walking on the surface. Dry time may vary due to
8am to 4:30pm Central Time.
temperature, humidity and surface porosity.
www.armorallhomecare.com
Directions for use:
Clean-Up: Clean equipment immediately with soap and water.
Storage: Do not store below 32˚F. Do not allow product to freeze.
Guidelines for Coverage Approximate coverage - sq. ft/ gallon
ARMOR ALL and the ARMOR ALL logo are registered
trademarks of The Armor All/STP Products Company
and are used under license by W.M. Barr & Co., Inc.
Actual coverage will vary due to surface porosity, texture and condition
Wood - Rough Sawn - 150 Wood Shingles - 100 Wood - Smooth Sawn - 250
SATISFACTION GUARANTEED
Plywood - 150
If you are not completely satisfied return your sales receipt with a description of your complaint.
Liability is limited to refund of the purchase price.
W.M. Barr & Co., Inc.
Memphis, TN 38113
© 2008 W.M. Barr & Co., Inc.
0
J4604
30192 60542
4