Installation Products
LVT/Vinyl Sheet Adhesives
Flip™ Spray Adhesive
• High-moisture guarantee
• Warranted for heavy rolling loads
• Simple one-step application process
• Open time: varies depending on adhesive coverage
• Working time: should not exceed 4 hours
• Spread rate: L VT and Commercial Sheet: 140–170 sq. ft./bottle;
VCT: 170–200 sq. ft./bottle
S-543 Commercial Sheet Flooring and LVT Adhesive
• High-moisture guarantee
• Reduced need for moisture remediation
• Open time: 10–20 minutes over porous, 30+ minutes over non-porous
• Working time: 8 hours after dry to touch
• Spread rate: 225–275 sq. ft./gal. Trowel: fine notch and back roll
S-288 Flooring Adhesive
• Creates a strong permanent bond to your floor
• Easy to trowel
• Open time: 10–20 minutes over porous, 30+ minutes over non-porous
• Working time: 60 minutes after dry to touch
• Spread rate: 250–300 sq. ft./gal. Trowel: fine notch
S-289 Releasable and Permanent Adhesive
• Easy to replace the floor once installed
• Allows for easy repairs on fiberglass and vinyl back floors
• Open time: 45–60
minutes (releasable); 10–20 minutes (permanent, sheet only)
• Working time: U nlimited (releasable); 60 minutes (permanent, sheet only)
• Spread rate: 2 75–325 sq. ft./gal. (releasable, roller);
250–300 sq. ft./gal. (permanent, sheet only), Trowel: fine notch
• Sheet: releasable or permanent; LVT: releasable only
High-Moisture
22 oz.
Bottle
93% RH
High-Moisture
90% RH
7 lbs. MVER for LVT
5 lbs. MVER for Sheet
Premium
90% RH for LVT
85% RH for Sheet
5 lbs. MVER
Releasable
80% RH
5 lbs. MVER
1 Gallon
4 Gallon
1 Quart
1 Gallon
4 Gallon
1 Gallon
4 Gallon
Grout for Alterna™
1 Quart
S-693 Acrylic Grout
• For use with Alterna™ flooring
• Ready for light traffic in 24 hours
• Flexibility—minimizes cracking with slight movements in the floor
• 12 colors
• Open time: approximately 3–8 minutes
• Working time: up to 10 minutes (working times may vary based on jobsite conditions, substrates, temperature and humidity)
• Spread rate: 244 sq. ft./gal., 12˝ square tile with 1/8˝ grout
1 Gallon
Vinyl Sheet Adhesives
COMMERCIAL
S-599 Vinyl Sheet Adhesive Premium Commercial
• Strong bond and shear strength
• Can be used for vinyl-, glass- and felt-backed sheet
• Open time: 10–20 minutes over porous, 30+ minutes over non-porous
• Working time: 60 minutes after dry to touch
• Spread rate: 250–300 sq. ft./gal. Trowel: fine notch
S-235 Sheet Flooring Premium Adhesive (Felt)
• Short open time; fast initial grab
• Installable on wider range of subfloors; Commercial grade
• Open time: 0–20 minutes over porous, 10–20 minutes over non-porous
• Working time: 40 minutes
• Spread rate: 1 25–150 sq. ft./gal. (porous), Trowel: reg notch;
225–275 sq. ft./gal. (non porous), Trowel: fine notch
FELT
S-254 Residential Flooring Adhesive (Felt)
• Short open time; Fast initial grab
• Open time: 0–20 minutes over porous, 10–20 minutes over non-porous
• Working time: 2 0 minutes (concrete), 60 minutes (wood/other substrates)
• Spread rate: 1 25–150 sq. ft./gal. (porous), Trowel: regular notch;
225–275 sq. ft./gal. (non porous), Trowel: fine notch
High Moisture
85% RH
5 lbs. MVER
Premium
80% RH
5 lbs. MVER
1 Gallon
4 Gallon
1 Quart
1 Gallon
4 Gallon
Standard
1 Gallon
80% RH
5 lbs. MVER
4 Gallon
1
Installation Products
Linoleum Adhesive
S-780 Linoleum Adhesive
• Creates a strong, permanent bond to the floor
• Ready for light traffic in 24 hours
• Open time: None over porous, 5–10 minutes over non-porous
• Working time: Approx. 25 minutes
• Spread rate: S
heet 120–135 sq. ft./gal. Trowel: regular notch;
Tile 150–175 sq.ft./gal. Trowel: v-notch 1/16˝ x 1/16˝ x 1/16˝
High-Moisture
85% RH
5 lbs. MVER
1 Gallon
4 Gallon
VCT/BIO Adhesives
Flip™ Spray Adhesive
• High-moisture guarantee
• Warranted for heavy rolling loads
• Simple one-step application process
• Open time: varies depending on adhesive coverage
• Working time: should not exceed 4 hours
• Spread rate: L VT and Commercial Sheet:140–170 sq. ft./bottle;
VCT: 170–200 sq. ft./bottle
VCT
S-515 Floor Tile Adhesive
• High moisture guarantee
• Can also be used over cutback adhesive residue
• Dries clear to easily see chalk lines
• Open time: 30+ minutes
• Working time: 24 hours
• Spread rate: 285–335 sq. ft./gal. Trowel: fine notch
S-750 Premium Floor Tile Adhesive
• Can also be used over cutback adhesive residue
• Can be used as a primer
• Open time: 30+ minutes
• Working time: 6 hours
• Spread rate: 275–350 sq. ft./gal. Trowel: fine notch
S-525 Bio-Flooring Adhesive
• High moisture guarantee
• Can also be used over cutback adhesive residue
• Water-resistant when fully cured
• Open time: Minimum of 20 minutes or until dry-to-touch
• Working time: 24 hours
• Spread rate: 275–325 sq. ft./gal. Trowel: fine notch
BIO and VCT
S-700 Floor Tile Adhesive Thin Spread
• Black asphalt adhesive
• Can also be used over cutback adhesive residue
• Can be used over metal subfloors
• Open time: 30+ minutes
• Working time: 18 hours
• Spread rate: 350–400 sq. ft./gal. Trowel: fine notch
High-Moisture
22 oz.
Bottle
93% RH
High-Moisture
1 Quart
1 Gallon
90% RH
7 lbs. MVER
4 Gallon
Premium
80% RH
5 lbs. MVER
1 Gallon
4 Gallon
High-Moisture
90% RH
7 lbs. MVER
1 Gallon
4 Gallon
Standard
1 Gallon
80% RH
5 lbs. MVER
4 Gallon
Hardwood/Laminate Adhesives
Summit™­All-in-One Adhesive
• Sound diminisher, moisture barrier and crack isolation membrane*
• Easy clean up with modified silane formula
• Open time: None
• Working time: 50 minutes
• Spread rate: 5 0–60 sq. ft./gal. for wood Trowel: v-notch;
70–80 sq. ft./gal. for parquet Trowel: square notch;
30–35 sq. ft./gal. for all in one application*
High-Moisture
Sound Reduction
All-in-One
85% RH*
10 lbs. MVER*
ProConnect™ Acrylic Adhesive
• Strong initial grab
• Easy clean up with water
• Open time: 15 minutes
• Working time: 35–60 minutes
• Spread rate: 5 0–60 sq. ft./gal. for engineered Trowel: v-notch;
70–80 sq. ft./gal. for parquet Trowel: square notch
Acrylic
Equalizer™ Urethane Adhesive
• Moisture cured – contains no water
• Long working time
• Open time: None
• Working time: 45–60 minutes
• Spread rate: 5 0–60 sq. ft./gal. for engineered Trowel: v-notch;
70–80 sq. ft./gal. for parquet Trowel: square notch
2
*When Summit trowel is used, included with adhesive.
4 Gallon
75% RH
3 lbs. MVER
Urethane
75% RH
3 lbs. MVER
1 Gallon
4 Gallon
3.5 Gallon
Installation Products
Specialty Products
S-761 Seam Adhesive for Sheet Flooring
Seams
• Quick and easy seaming method for vinyl sheet and linoleum sheet
• Excellent seam integrity
• Open time: None
• Working time: 15 minutes
• Spread rate: 144 lin. ft./8 oz. bottle (with 1/8˝ bead)
S-500 Seam Coating Kit
Seams
• Low Gloss urethane seam coater
• Required for Residential Felt Backed sheet seams
• Optional for Vinyl Backed sheet seams
• Open time: None
• Working time: 3 hours
• Spread rate: 50–60 lin. ft./kit
EverSeal™ Joint Adhesive — Hardwood/Laminate
Joints
• Strong water resistant bond between tongue and groove
• Use for floating laminate and wide plank engineered hardwood in full bathrooms,
high moisture areas and light commercial environments
• Use for end joint
• Spread rate: Up to 150 sq.ft./16 oz. bottle (with 3/32˝ bead)
S-580 Flash Cove Adhesive
• Pressure sensitive adhesive with unlimited working time
8 oz. Bottle
Kit
16 oz.
Bottle
Flash Cove
1/2 Gallon
Wall Base
30 oz. Tube
• Open time: 20–30 minutes
• Working time: Unlimited
• Spread rate: 200–250 sq. ft./half gal.
S-725 Wall Base Adhesive
• No open time – immediate installation
• Easy clean up
• Open time: None
• Working time: 15 minutes
• Spread rate: 300–350 lin. ft./gal. (with 4˝ wall base)
1 Gallon
4 Gallon
S-240 Epoxy Adhesive
• For use with Commercial sheet, Linoleum sheet, VCT and LVT
• Great for heavy loads
• Can be used on multiple substrates
• Open time: 10–20 minutes
• Working time: 60 minutes
• Spread rate: 170–190 sq. ft./gal. Trowel: fine notch
Epoxy
90% RH
8 lbs. MVER
S-202 SDT Adhesive
• Supplied with copper grounding strips – Integral static
dissipative element
• Excellent bond strength
• Open time: 60 minutes
• Working time: 6 hours
• Spread rate: 150 sq. ft./gal. Trowel: fine notch
1 Gallon
SDT
1/2 Gallon
75% RH
3 lbs. MVER
1 Gallon
4 Gallon
Floor Preparation
S-135 VapArrest™ Professional Moisture
Retardant System
• For wood floors, floating vinyl floors and laminate
• Reduces water vapor transmission up to 75% (to less than 3 lbs./1000 sq. ft./24 hrs.)
• Reduces potential for mold and mildew growth
• N o additional prep time, easy to apply, rapid curing; ready to install in 12 hours
• Used over cementitous leveling compound; Low odor, no VOCs
• Residential applications do not require moisture tests
Moisture Mitigation
85% RH
12 lbs. MVER
1.1 Gallon
2.2 Gallon
3
Installation Products
Floor Preparation
S-184 Fast-Setting Patch & Underlayment
• Patch, skim coat and level ceramic tile, quarry tile, marble and terrazzo (except metal terrazzo strips) and concrete on any grade level
• C over existing asphalt cutback adhesive over concrete
• Patch and repair small voids, and skim coat wood underlayments; may be used for overall leveling of approved suspended wood underlayments
• Patches up to 1/2˝; compressive strength 4500psi
S-194 Patch Underlayment & Embossing Leveler and
S-195 Underlayment Additive
• Patch, skim coat and level ceramic tile, quarry tile, marble and terrazzo (except metal terrazzo strips) and concrete on any grade level
• Patch, skim coat, and level all grade levels of steel, stainless steel, brass and lead when mixed with S-195
• C over existing asphalt cutback adhesive residue over concrete
• Patch and repair small voids, and skim coat wood underlayments; may be used for overall leveling of approved suspended wood underlayments
when mixed with S-195
• N ot recommended for use on strip wood floors
• Fill and level the embossing of single-layer existing resilient floor prior to the installation of new residential resilient floor when mixed with S-195
• Patches up to 1˝; compressive strength >5000psi
S-185 Latex Primer
• Primer used with all Armstrong® patches, underlayments and latex based adhesives
• C an be used on all grade levels of concrete, poured in place gypsum underlayments, approved wood underlayments,
ceramic tile, quarry tile, terrazzo and marble
• Primer for wood and concrete with self-adhering tile
S-1840 Quiet Comfort™ Luxury Flooring Underlayment
• N oise: provides superior reduction versus standard closed cell foam and fiber pad underlayments
• Moisture: does not promote mold or mildew growth and will not decay
• Construction: high density cross-linked polyethylene foam laminated to 3 mil polyethylene film
• STC/IIC: 66/68
S-1837 Quiet Comfort Underlayment
40 lb. Bag
10 lb. Box
25 lb. Bag
1 Gallon
1 Gallon
300 sf Roll
• Designed for use with Armstrong Luxury Flooring, Alterna™, and LVT products
• Excellent acoustic barrier for through-the-floor and in-room footfall noise reduction
• Cross-linked polypropylene provides moisture barrier which resists mold and mildew
• Weight: 6 lbs./roll
• STC/IIC: 62/64
S-1836 Quiet Comfort Premium
25 lb. Bag
• N oise: provides superior reduction versus standard closed cell foam and fiber pad underlayments
• Moisture: does not promote mold or mildew growth and will not decay
• Construction: closed-cell polyethylene foam laminated to 3 mil polyethylene film
• STC/IIC: 51/53
100 sf Roll
1600 sf Roll
100 sf Roll
1600 sf Roll
Installation Tools
S-33 Edge Trimmer and S-32 Blades
• Designed to trim the factory edge of non-patterned Armstrong sheet flooring quickly, easily, and accurately;
Slides on subfloor so material does not have to be lifted for cutting
• Sturdy yet lightweight all-metal construction
• Front finger channel for convenience and comfort
• One blade designed for faster replacement; Uses S-32 Edge Trimmer Blades
S-153 Scribing Felt
4
Blades
450 sf Roll
• Gray cellulosic and synthetic fiber felt that cuts cleanly with a knife or scissors
• Does not readily break or stretch, and clearly shows all scribe marks
• Lightweight and packed in rolls 36˝ x 150 lin. ft.
S-891 Notched Steel Trowel
Trimmer
Trowel
• N otches on both sides
• Armstrong Regular Notch: 1/16˝ deep, 1/16˝ wide, 3/32˝ apart
• Armstrong Fine Notch: 1/32˝ deep, 1/16˝ wide, 5/64˝ apart
• Front edge is angled to provide easy spreading along walls and fixtures
• Size: 11˝ in length
S-892 Replaceable Blade Trowel Handle and Replacement Blades
Trowel
Blades
• Trowel includes one regular notched blade, (S-893), and one fine notched blade, (S-894)
• Makes it easy to use the correct notching by simply attaching a new blade
• Blades also available separately
• Size: 11˝ in length
FP7440F8871-915 ©2015 AWI Licensing Company Printed in the United States of America.
Armstrong and the Armstrong logo are registered in the United States and Canada. BBT® and BioBased Tile® are registered in the United States only.