1
3
2
5
4
6
8
7
NOTES:
PACKAGE DETAILS
1. SUCTION COMBINATION VALVE, DISCHARGE VALVE, RELIEF PIPING
& LIQUID PIPING MUST BE COMPLETELY SUPPORTED
INDEPENDENTLY OF PACKAGE, COMPRESSOR MATING FLANGES
MUST BE IN EXACT ALIGNMENT WITH FACES CONCENTRIC &
PARALLEL WHEN ALL CAP SCREWS ARE REMOVED. IF NOT, SERIOUS
MECHANICAL DISTORTION MAY OCCUR TO THE COMPRESSOR
CASING WITH RESULTING DAMAGE TO THE BEARINGS, SEALS, ETC.
OIL SEPARATOR
OD: 20
WSL: 114
DWP: 300 PSIG
65 7/8 LIQUID INJECTION INLET
2. A MINIMUM CLEARANCE OF 36" (FRONT/ LEFT SIDES) AND 18"
(REAR/ RIGHT SIDES) MUST BE PROVIDED TO SERVICE PACKAGE
COMPONENTS WITHOUT INTERFERENCE FROM PIPING, ELECTRICAL
CONDUIT, OIL FILTERS, ETC.
SUCTION VALVE
MOUNTING: MOUNTED (AS SHOWN)
MANUF: AWP
SIZE: 6 IN
63 15/16 SUCTION
3 1/8 LIQUID
INJECTION INLET
3 1/2 ECONOMIZER
INLET
3. A LEVEL FLOOR MOUNTING PAD MUST BE PROVIDED BY OTHERS,
CAPABLE OF SUPPORTING THE OPERATING WEIGHT OF THE SCREW
COMPRESSOR PACKAGE.
H
DISCHARGE VALVE
MOUNTING: MOUNTED (AS SHOWN)
MANUF: AWP
SIZE: 3 IN
15 1/4
ECONOMIZER
4. RELIEF LINE TO BE PIPED TO OUTSIDE ATMOSPHERE PER
ANSI/ASHRAE 15-(LATEST EDITION).
DUAL RELIEF VALVES
MANUF: SHANK
MODEL: 813
SIZE: 1/2" FPT x 1" FPT
PRESSURE RATING (PSIG): 250#
CAPACITY: 44LB/MIN AIR
5. ALL DIMENSIONS INCLUDING THOSE ON FIELD CONNECTED
NOZZLES ARE WITHIN 3/4" TOLERANCE. IT IS RECOMMENDED THAT
FIELD PIPING ALLOW FOR SOME PLAY IN FITTING PACKAGE NOZZLES,
ESPECIALLY IF FIELD PIPING IS STARTED BEFORE UNIT IS IN PLACE.
G
LIQUID INJECTION
INLET: 3/4 SW
7. REMOVE VALVE BONNET/SEAT ASSEMBLY BEFORE WELDING
VALVE TO SYSTEM PIPE WORK, TO AVOID DAMAGE TO VALVE SEAT.
8. RECOMMENDED UNIT ANCHORING
(4) 3/4"-10 NC HEX HD. BOLTS 2 1/2" LG., FLAT WASHER & TAPPED
CONCRETE INSERT, NOT FURNISHED BY GEA. CARRY FOUNDATION
DOWN TO FIRM BEARING, TOP SURFACE MUST BE SMOOTH AND
LEVEL. FOUNDATION PADS MAY BE CAST ON EXISTING FLOOR IN
GOOD CONDITION AND SHOULD BE PINNED.
ECONOMIZER
INLET: 2.00 BW
30 5/8
DISCHARGE
35 1/4 DUAL
RELIEF VALVES
6. SUCTION AND DISCHARGE WILL BE FURNISHED WITH A SLIP-ON
FLANGE WHEN OPTIONAL FACTORY INSTALLED STOP VALVES ARE
NOT PURCHASED, OR IF STOP VALVES ARE SHIPPED LOOSE.
7 7/8 SUCTION
PUMPOUT
SIZE: 1 IN FPT
GFORCE ENCLOSURE
SIZE: SMALL CARBON STEEL (22H x 26W x 8D)
APPROXIMATE OVERALL LENGTH 142 INCHES
9. IF THE PACKAGE IS INSTALLED IN AN ENVIRONMENT WITH A
MINIMUM AMBIENT TEMPERATURE BELOW 60 F, SPECIAL
CONSIDERATION NEEDS TO BE GIVEN TO ENSURE THE OIL REACHES
A SAFE COMPRESSOR START TEMPERATURE. SEVERAL SOLUTIONS
ARE AVAILABLE DEPENDING ON THE INSTALLATION ENVIRONMENT,
PLEASE CONSULT FACTORY TO REVIEW OPTIONS.
OIL PUMP MOTOR
HP: 2.0 HP
FRAME: 90L
MANUF: WEG
ENCLOSURE: TEFC
APPROXIMATE OVERALL WIDTH 52 INCHES
APPROXIMATE OVERALL HEIGHT 82 INCHES
2
F
COMPRESSOR MOTOR (AS SHOWN)
HP: 400HP
FRAME: 447-9TS
MANUF: WEG
ENCLOSURE: ODP
OIL
TYPE: FES #1
E
2 3/4
PACKAGE BASE WEIGHT: 6,200 LBS.
ADD FOR ECON VALVE STATION: 85 LBS.
ADD FOR MOTOR:
WEG 444-5TS 200 HP: 1,537 LBS.
250 HP: 1,806 LBS.
300 HP: 2,007 LBS.
SECTION A-A
FOOT DETAIL
WEG 447-9TS 350 HP: 1,819 LBS.
400 HP: 1,896 LBS.
450 HP: 2,073 LBS.
500 HP: 2,139 LBS.
600 HP: 2,359 LBS.
4
52 1/2
CENTER OF GFORCE DISPLAY
33 1/8 ECONOMIZER
A
23 1/4 LIQUID
INJECTION INLET
A
3 13/16
PUMPOUT
4
2
8
3 5/8
B
31 1/2
21 11/16
DISCHARGE
19 5/16 COOLER
OUTLET
C
15 3/4
4X 1"
ANCHOR
BOLT HOLES
26 1/4 DUAL
RELIEF VALVES
700 HP: 3,241 LBS.
800 HP: 3,528 LBS.
71 3/4 SUCTION
WEG 5010S
D
5 5/16
35 1/2
29 15/16 DISCHARGE
17 3/4
PUMPOUT
68 1/4
NOTES:
1. DRAWINGS ARE PROVIDED FOR PROPOSAL PURPOSES ONLY AND ARE NOT INTENDED FOR CONSTRUCTION.
A
2. EQUIPMENT SHOWN INCLUDES OPTIONAL ACCESSORIES.
3. DESIGN IS SUBJECT TO CHANGE WITHOUT NOTICE.
4. CERTIFIED DRAWINGS AND PROJECT DOCUMENTATION IS PROVIDED WITH ORDER.
GENERAL ARRANGEMENT
230-290GLX HIGHSTAGE R-717 LI
SPECIFICATIONS
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN INCHES
PROPOSAL ONLY
TOLERANCE = SEE NOTE #5
MATERIAL =
WEIGHT = SEE TABLE
DO NOT SCALE
REV
DATE
REVISION
BY
AP
GEA Refrigeration
North America, Inc.
DATE
DRAWN
APPROVED
SCALE
10/28/2013
RKC
SIZE
DRAWING NUMBER
REV.
D
011-100361-005
00
SMG
NO SCALE
SHEET NUMBER
ORIG. NO.
1
OF
1
ORIG. REV.
CONFIDENTIAL: THE INFORMATION HEREON IS CONFIDENTIAL AND MAY NOT BE REPRODUCED OR DIVULGED WITHOUT THE WRITTEN PERMISSION OF GEA REFRIGERATION NORTH AMERICA, INC.