Symbol
Wdg
Ohms
+ 12.5%
R
Voltage @ FP
Volts
Nominal
VP
31.6
Current @ FP
Amps
Nominal
IP
13.16
Force Sensitivity
Inductance ****
N/Amp
+ 10%
LB/Amp
+ 10%
V/(m/sec)
+ 10%
V/(ft/sec)
+ 10%
milli-henry
+ 30%
Linear Actuator Parameters *
Units
N
Peak Force **
Actuator Constant
Electrical Time Constant
Mechanical Time Constant
Theoretical Acceleration
N
Watt
LB/ Watt
milli-sec
milli-sec
Watts
KA
LTR
ECO NO.
X1
130068
X2
130296
DESCRIPTION
APP'D
DATE
RG
MG
03/12/13
UPDATED TO AS BUILT CONDITION
RG
MG
09/06/13
4.50
18
16
4.00
D
14
12
3.50
10
3.00
8
6
4
-10
-7.5
-5
-2.5
0
2.5
5
7.5
10
2.50
2.00
1.50
12.5
STROKE, mm
2.94
tE
1.00
4.4
0.50
353.5
1159.8
f max
26.8/29.7
PP
416
0.00
‐8
‐7
‐6
‐5
in
Kg
4.11
Temp
155
WTC
LB
Kg
WTT
LB
‐2
LEAD WIRE
RED
GREEN
BLACK
IDENTIFICATION
VCC
GND
VO
WHITE
VPP
2.4
FORCE VECTOR
27
2
3
4
5
6
7
8
9
10 11 12 13
C
DESCRIPTION
INPUT VOLATAGE ( 5 VOLTS)
GROUND
OUTPUT VOLTAGE
VOLTAGE FOR PROGRAMMING ONLY,
NOT TO BE USED BY CUSTOMER
+
30 (@ MID-STROKE)
POWER CABLE ASSEMBLY
(ALPHA WIRE: P/N 5162C, 2X 18 AWG)
18 INCHES [457mm] MIN LONG
(
4X M5x0.8-6H THRU
9.0) FIELD ASSEMBLY
4X 90°
27
45.00
B
70.00
74
86.0
136
SHAFT END CONFIGURATION
12mm Diameter
12mm Diameter,Internal Thread M8x1.25 X 16 mm Deep
12mm Diameter,External Thread M12x1.75 X 16mm Long
RoHS
THESE COMMODITIES, TECHNOLOGY OR SOFTWARE IF EXPORTED FROM THE
UNITED STATES SHALL BE IN ACCORDANCE WITH THE EXPORT ADMINISTRATION
REGULATIONS. DIVERSION CONTRARY TO U.S. LAW IS PROHIBITED.
Proprietary rights of BEI Kimco
are involved in the subject
matter of this material and all
manufacturing, reproduction,
use, and sales pertaining to such
subject matter are expressly
reserved. This confidential and
proprietary document is
submitted for a specified purose,
and the recipient by accepting
this material agrees that this
material will not be used , copied,
or reproduced in whole or in part
nor its contents revealed in any
manner or to any person except
to meet the purpose for which it
was delivered.
5. A POSITIVE (+) VOLTAGE APPLIED TO RED LEAD ON THE POWER CABLE ASSEMBLY
WILL PRODUCE A FORCE ON THE COIL ASSEMBLY IN THE POSITIVE (+) DIRECTION.
4. -12E SHAFT CONFIGURATION SHOWN.
3. ALL ABBREVIATIONS IAW ASME Y14.38.
2. INTERPRET DRAWING IAW ASME Y14.100.
1. INTERPRET DIMENSIONING AND TOLERANCING IAW ASME Y14.5M-1994.
NOTES: UNLESS OTHERWISE SPECIFIED
7
1
5.
5.29
4.
(-12E SHOWN)
8
0
1.66
B
(DASH)
‐12S
‐12I
‐12E
‐1
0.755
* AT MID-STROKE POSITION AND @ 25 C AMBIENT TEMPERATURE
** 10 SECONDS @ 25 C AMBIENT & 155 C COIL TEMPERATURE
*** @25 C AMBIENT & 155 C COIL TEMPERATURE
**** MEASURED AT 1000 Hz.
SENSOR CABLE
(ALPHA WIRE: P/N 86004CY, 4X 28 AWG)
18 INCHES [457mm]MIN LONG
A
‐3
POSITION SENSOR
0.02
QTH
‐4
STROKE, mm
12.5
1.51
ºC
DRN
INITIAL RELEASE
1.31
mm
Maximum Allowable Coil Winding Temp
1
20
0
-12.5
13.09
X2
LAS28-53-000A-P01-DASH
22
2
13.5
0.492
ºC/Watt
Total Weight
3.15
60
+ in
Thermal Resistance of Coil
Weight of Coil Assembly
6.18
60.1
+ mm
Clearance on Each side of Coil
20.28
3
‐13 ‐12 ‐11 ‐10 ‐9
Hz
& Sinusoidal/Triangular Motion
Stroke:
4.56
266.9
aT
ft/sec 2
20.28
Value
tM
m/sec 2
Max Theoretical Frequency @ Full Stroke
Power I2R @ FP
L
FCS
LB
N/
KB
FP
LB
Continuos Stall Force ***
Symbol
KF
A
2.4
DC Resistance
Back EMF Constant
C
Tol
4
X2
D
Units
5
6
5
4
METRIC DRAWING
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED:
-ALL DIMENSIONS ARE IN MILLIMETERS
-BREAK SHARP EDGES 0.4 MAX
-SURFACE ROUGHNESS 1.6
-DIMENSIONS APPLY AFTER FINISH
-MAX FILLET R0.25
-DIAMETERS SHALL NOT EXCEED A
RUNOUT OF 0.13 FIM
DRAWN
BEI
KIMCO MAGNETICS DIVISION
VISTA, CA 92081
DATE
GUERRERO
TITLE
LINEAR ACTUATOR
SYSTEM
03/11/13
MECH CHECK
03/11/13
TOLERANCES:
ANGULAR
DECIMALS
X.
0.8
0 30'
X.X
0.25
X.XX
0.13
DO NOT SCALE DRAWING
3
APPD
GODKIN
FILE NO.
03/12/13
L\TOP LEVEL\LAS\
SIZE
D
SCALE
2
FSCM NO.
REV
DWG NO.
X2
55789 LAS28-53-000A-P01-DASH
1/1
SHEET
1 OF 1
1
LAS28-53-000A-P01-DASH
Winding Constants *
6
OUTPUT VOLTAGE, Volts
7
FORCE SENSITIVITY, N/Ampere
8
A