Stanford University s School of Engineering
Product Design
2016–2017 Program Sheet
Final version of completed and signed program sheet due to the department no later than one month
prior to the last quarter of senior year.
*Follow all requirements as stated for the year of the program sheet used.*
Name:
SU ID #:
Phone:
Email:
Today's Date:
Month/Yr B.S. expected:
Mathematics and Science Requirement
Dept
Transfer/AP Approval
Course Title
P if
Transfer
Mathematics (20 units minimum; see Note 1 & 2)
Initials
Date
Units
Grade
Mathematics Unit Total (20 units minimum)
SoE Science (15 units minimum; see note 1)
PHYS
41 Mechanics (req'd)
PHYS
43 Electricity and Magnetism (req'd)
PHYS
45 Light and Heat (req'd)
Science Elective (from SoE approved list, see Note 3)
SOE Science Unit Total (15 units minimum)
Behavioral Sciences (8 units minimum)
PSYCH
1 Intro to Psychology (req'd)
PSYCH
Psychology or HumBio Elective (3-5 units see Note 4)
Behavioral Science Unit Total (8 units minimum)
Science Unit Total (SoE + Behavioral) (23 units minimum)
Mathematics and Science Unit Total ( 43 units minimum)
Technology in Society Requirement (1 course req'd; course must be on Approved list in UGHB the year taken)
See SoE Approved Courses list at <ughb.stanford.edu>
NOTES
*
All courses taken for the major must be taken for a letter grade if offered by the instructor.
*
This form is available as an Excel file at http://ughb.stanford.edu/; you must use a program sheet from a year you
were enrolled at Stanford. The printed form must be signed by the advisor and by the ME Student Services
Manager. Changes must be initialed
*
Read all emails from your major department; this is the SoE's only method of conveying key information to
Engineering
majors.
*
Minimum
Grade
Point Average (GPA) for all courses in Engineering Fundamentals and Product Design Depth
(combined) is 2.0
*
Transfer and AP credits in Math, Science, Fundamentals, & TIS must be approved by the SoE Dean's office.
Transfer
credits
Engineering
Depth
approved
by the
Advisor.noTransfer
credit informationcourses
and petitions
*
All
courses
listedinon
this form must
bemust
listedbe
under
only one
category;
double-counting.Delete
not taken.
( 1 ) AP units can be applied; have these approved by SoE Dean's Office before final quarter.
( 2 ) CME 100, 102, 104 & 106 are highly recommended, NOTE: The Math 40 series will be discontinued after AY1617;
MATH 19/20/21 or AP credit may be used instead.
( 3 ) At least 15 units must be from the School of Engineering approved science list in the undergraduate handbook
(Approved Courses page at http://ughb.stanford.edu).
( 4 ) Psych elective courses numbered 30-200; HUMBIO 82A and 160 are pre-approved (if the PSYCH elective was
taken prior to the requirement being increased to 3 units minimum in 2012-13, it is allowed without petition to be
one unit short in the Science/Behavioral Sciences section).
Product Design program continued
Engineering Fundamentals (3 courses required, 11 units minimum)
ENGR
40+ Introductory Electronics 40 or 40A or 40M (one req'd)
ENGR
70A Programming Methodology (req'd)
Fundamentals Elective: See Note 5, CS 106B or X (ENGR 70B or X) not allowed.
3 or 5
5
3 or 4
Engineering Fundamentals Total (3 courses required)
Product Design Depth (53-56 units)
Dept
ENGR
ME
ME
ME
ME
ME
ME
ME
ME
ME
ME
Transfer/AP Approval
P if
Initials
Date
Transfer
Course Title
14
80
101
103D
110
112
115A
115B
115C
203
216A
Units
Grade
Introduction to Solid Mechanics (req'd; see Note 6)
Mechanics of Materials (req'd)
Visual Thinking (req'd; see Note 6)
Engineering Drawing and Design (req'd, see Note 7)
Design Sketching (req'd; see Note 6)
Mechanical Engineering Design (req'd; see note 8; WIM)
Introduction to Human Values in Design (req'd)
Product Design Methods (req'd)
Design and Business Factors (req'd; see Note 9)
Design and Manufacturing (req'd; see Note 7)
Advanced Product Design: Needfinding (req'd)
Product Design Capstone (req'd; see Note 10)
Art Studio Elective or CS Elective (100 series or higher)
Art Studio Elective or CS Elective (100 series or higher)
Art Studio Elective or CS Elective (100 series or higher)
Product Design Engineering Depth Total (53-56 units)
Program Totals
Mathematics and Science (43 units minimum)
Product Design Depth (53-56 units minimum)
Program Approvals
Advisor
Printed Name:
Signature:
Date:
Departmental
Printed Name:
Signature:
Date:
School of Engineering (No action required -- office use only)
Printed Name:
Signature:
Date:
NOTES (continued from page 1)
( 5 ) Choose one more fundamental from: ENGR 10, 15, 20, 25B or E, 30, 50, 50E, 50M, 60, 62, 90. Note that CS 106B
or X (ENGR 70B or X) are not allowed to fulfill elective.
( 6 ) If ENGR 14 and/or ME 110 and/or ME101 were taken prior to the courses being offered for 4 and 2 units, depth
total may be reduced by 1-3 units with no petition required.
( 7 ) ME 103D and 203 should be taken concurrently.
( 8 ) ME 112 meets the Writing in the Major (WIM) requirement.
( 9 ) ME 115C is the ONLY course that can be waived if student takes a quarter overseas. Students should plan their
overseas quarter to take place in Sophomore year, or spring quarter of Junior year only. If the student elects to go
overseas Junior year, the total Depth units will be reduced by 3; this is approved without petition.
( 10 ) Choose one of the following combinations: 1) ME 216B + ME216C, or 2) ME114 + any other course in SoE