Vibration Isolation To help address the issues of vibration and noise control/dampening vibration in mechanical, refrigeration, HVAC and electrical installations, Eaton offers the following B-Line series vibration isolation products. It is our continuing effort to offer the industry quality support system products that meet the demands of today’s construction environment. The following pages depict vibration isolation and noise control products that are commonly specified and required on piping, duct and equipment, but not limited to mechanical rooms. As an aid in choosing the proper vibration control device, the chart shown on the following page is a reference for obtaining Vibration Isolation Efficiency. Considerations must be given to the desired deflection and the frequency (R.P.M.). The Theory of Vibration Isolation Background Soils, floors, ceilings, walls, etc. deflect as the result of applied forces. Cyclical forces generated by machines result in work done on the floors, etc. Under steady state conditions, this work is stored as potential energy in the floor each cycle and returned as work in forcing the machine back to its equilibrium position. Disturbance is transmitted during this flexing. Vibration Isolation is needed when disturbing force magnitudes are expected to be great enough to cause damage or annoyance. Vibration Isolation Assumption Fact 1. We know the effects of vibration isolation (efficiency) Formula for calculation shown below. 2. We know the magnitude of the disturbing forces created by the machines Equipment manufacturers rarely provide these data. These forces are seldom known except in generalities. 3. We know the magnitude of disturbing forces beyond Detailed calculations require so many simplifying assumptions that the resulting answers have questionable value in addition to being prohibitively expensive. Reliance is placed on brief calculations, general rules, and past experience. Consideration of items 1. and 2. is essential to determine acceptable isolation efficiency. Unfortunately manifold complexities prevent inclusion of steps for determination of these efficiencies in this document. Eaton 251 B-Line series Pipe Hangers & Supports Vibration Isolation Data Natural frequency of isolation system fn (cycles per minute) Visualize a machine suspended barely above 4 springs (one on each corner). Now release the suspension. The machine will deflect the springs and be pushed up and return a number of times with diminishing deflection until it comes to rest. The spring deflection at rest is called the static deflection. The number of cycles per unit time is the natural frequency of the isolation system. Unlike multi-degree of freedom floors with limitless natural frequencies, springs essentially have only one natural frequency. fn = 188 1 static deflection (inches) [ Vibration isolation efficiency % = 100% x 1 - 1 (fd ÷ fn)2 - 1 ] Transmitted force ft (pounds) ft = fd (100% - isolation efficiency) Note that fn must be compared to fd for satisfactory isolation efficiency. Also note that the force transmitted can be greater than the disturbing force when fn is close to or equals fd. This condition is called resonance and is avoided in vibration isolation. Natural frequency of floor or soil Visualize the effect of dropping a load on the floor. This floor will deflect and spring back diminishingly a number of cycles until it comes to rest. The number of these cycles per unit time is a natural frequency of the floor. It is essentially independent of the magnitude of deflection and hence is a characteristic of a given floor if given a light tap or a hard jolt at the same location. The floor has many natural frequencies. The lowest natural frequency is called the fundamental. It is characterized by maximum deflection at mid span. The higher natural frequencies are generally less bothersome than the fundamental since they are less likely to be excited by machines in common use and are more quickly damped. The greater a floor deflects under a given load, the lower the fundamental frequency of that floor. Soft, springy floors have low fundamentals. Hard, solid floors have high fundamentals. Disturbing frequency fd (cycles per minute) With few exceptions, the speed (RPM) of the machine will be most representative of the frequency of the disturbance. Disturbances are more readily transmitted when the disturbing frequency is close to a natural frequency of the floor or soil. For this reason, these characteristics are important considerations i designing a trouble-free installation. Disturbing force fd (pounds) The disturbing force causes the problem. It is constantly changing from maximum positive through zero to maximum negative through zero to maximum positive each cycle. It results from unbalanced reciprocating and rotating masses. Its peak magnitude varies from ounces to tons. From less than 1% to over 60% of the weight of some types of machines. Generally this force will increase with time in a given machine as bearings wear, deposits form and moving parts get out of balance with each other. Proper Sizing Vibration Isolation Once it is determined as to what type of vibration dampening device is needed, weight loading is the next crucial step. As a built in safety measure, take the actual weight of supported pipe or equipment (consider all accessories - i.e. valves, insulation, brackets, etc...) and multiply by 1.25. Then refer to the sizing chart for the selected product to determine part number. Sizing: Divide weight of equipment by points of support to determine load requirement per support. Example: 240 Lb. (90.7 kg) piece of equipment, 4 support points, take 240 x 1.25 = 300 Lbs. (136.1kg) (safety measure), then take 300 ÷ 4 = 75 Lbs. (34.0 kg) Specify appropriate vibration device rated at 75 Lbs. (34.0 kg) for each of the support points. If weight of equipment is unequally proportionate, select mounts to satisfy the weight distribution. B-Line series Pipe Hangers & Supports 252 Eaton Vibration Isolation IE Computer Isolation Efficiency fn = 188 1 static deflection (inches) Transmissibility = 1 (fd ÷ fn)2 - 1 Undamped Static Deflection - (Inches) (Cycles Per Minute) fn Natural Frequency of Isolation System 3 HX = 180 cpm = 1.1” Deflection fd Disturbing Frequency - (cycles per minute) % Isolation Efficiency – 100% - Transmissibility Critical Installations 96% to 99% Vibration Isolation Efficiency recommended (only 1% to 4% of disturbing vibration transmitted). Standard Installations 90% to 95% Vibration Isolation Efficiency recommended (only 5% to 10% of disturbing vibration transmitted). Non-Critical Installations 75% to 89% Vibration Isolation Efficiency recommended (only 11% to 24% of disturbing vibration transmitted). Vibration Isolation For 1/4" (6.3mm) deflection: Specify B-Line series RM and RQ Neoprene Mountings or B-Line series RH Neoprene Hangers. For 1/2" (12.7mm) deflection: Specify B-Line series RMD and RQD, (or JQTN fo OSHPD pre-approved) Neoprene Mountings or BLine series RHD Neoprene Hangers. For 1"-2" (25.4mm-50.8mm) deflection: Specify B-Line series CHSCS, CH30SCS, HHSCS, and HH30SCS Housed Spring Mountings. For larger deflection requirements, consult factory. Eaton 253 B-Line series Pipe Hangers & Supports Vibration Isolation NNP Type - Ribbed Neoprene Vibration Pad Use: Is used under equipment to dampen noise and vibration in floor caused by medium and high speed equipment. • Recommended load capacity: Up to 50 lbs./sq.in. (0.042 kgf/mm2) with a range of 25-70 lbs./sq.in. (0.021-0.059 kgf/mm2) • Thickness: 3/8” (9.5mm) • The NNP type has a deflection of 1/8" (3.1mm). For greater deflection, use multiple pads in layers • Non-skid: The pad has an alternating height rib pattern to minimize slip • Durable: Material is oil-resistant Neoprene • Typical Applications: Air conditioners, cooling towers, compressors, fans, generators, pumps, piping, process equipment, transformers, etc. 3/8" (9.5) L W Dimensions Rated Load L W Lbs. (kN) in. (mm) in. NNP-4 200 (.89) 2" (50.8) NNP-9 450 (2.00) 3" (76.2) NNP-16 800 (3.56) NNP-36 1800 (8.00) NNP-81 4050 NNP-324 16200 Wt. Each (mm) Std. Pkg. Lbs. (kg) 2" (50.8) 48 .04 (.02) 3" (76.2) 36 .10 (.05) 4" (101.6) 4" (101.6) 24 .17 (.08) 6" (152.4) 6" (152.4) 24 .39 (.18) (18.01) 9" (228.6) 9" (228.6) Bulk .87 (.39) (72.06) 18" (457.2) 18" (457.2) 6 3.50 (1.59) Vibration Isolation Part No. All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 254 Eaton Vibration Isolation CNP Type - Cork and Ribbed Neoprene Vibration Pad Use: Is used under equipment to dampen noise and vibration in floor caused by medium and high speed equipment. • Recommended load capacity: Up to 50 lbs./sq.in. (0.042 kgf/mm2) with a range of 25-70 lbs./sq.in. (0.021-0.059 kgf/mm2) • Thickness: 1” (25.4mm) • The NNP type has a deflection of 3/16" (4.7mm). For greater deflection, use multiple pads in layers • Non-skid: The pad has an alternating height rib pattern to minimize slip • Durable: Material is oil-resistant Neoprene • Typical Applications: Air conditioners, cooling towers, compressors, fans, generators, pumps, piping, process equipment, transformers, etc. 1" (25.4) L Part No. Dimensions Rated Load Lbs. W L W (kN) in. (mm) in. (mm) Std. Pkg. Wt. Each Lbs. (kg) Vibration Isolation CNP-4 200 (.89) 2" (50.8) 2" (50.8) 48 .07 (.03) CNP-9 450 (2.00) 3" (76.2) 3" (76.2) 36 .16 (.07) CNP-16 800 (3.56) 4" (101.6) 4" (101.6) 24 .28 (.13) CNP-25 1250 (5.56) 5" (127.0) 5" (127.0) 24 .44 (.20) CNP-36 1800 (8.00) 6" (152.4) 6" (152.4) 24 .63 (.29) CNP-81 4050 (18.01) 9" (228.6) 9" (228.6) Bulk 1.40 (.64) CNP-324 16200 (72.06) 18" (457.2) 18" (457.2) 6 5.60 (2.54) CNP-3x36 5400 (24.02) 3" (76.2) 36" (914.4) 6 1.89 (.86) CNP-4x36 7200 (32.02) 4" (101.6) 36" (914.4) 6 2.52 (1.14) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 255 B-Line series Pipe Hangers & Supports Vibration Isolation CNNK Type - Cork, Ribbed Neoprene and Steel Vibration Pad Use: Is used to dampen noise and vibration in floor caused by medium and high speed equipment. • Recommended load capacity: Up to 50 lbs./sq.in. (0.042 kgf/mm2) with a range of 25-70 lbs./sq.in. (0.021-0.059 kgf/mm2) • Overall thickness: 11/2” (38.1mm) Has 1/4” (6.3mm) steel plate for even weight distribution. Hole in center will accept up to 3/4” bolt • The CNNK type has a deflection of 3/16" (4.7mm). For greater deflection, use multiple pads in layers • Non-skid: The pad has an alternating height rib pattern to minimize slip • Durable: Material is oil-resistant Neoprene • Typical Applications: Air conditioners, cooling towers, compressors, fans, generators, pumps, piping, process equipment, transformers, etc. 13/16" (20.6) dia. hole 11/2” (38.1) W Part No. Dimensions Rated Load L W Wt. Each Lbs. (kN) in. (mm) in. (mm) Std. Pkg. CNNK-4 200 (.89) 2" (50.8) 2" (50.8) 48 CNNK-9 450 (2.00) 3" (76.2) 3" (76.2) 36 .90 (.41) CNNK-16 800 (3.56) 4" (101.6) 4" (101.6) 24 1.60 (.73) CNNK-25 1250 (5.56) 5" (127.0) 5" (127.0) 24 2.50 (1.13) CNNK-36 1800 (8.00) 6" (152.4) 6" (152.4) Bulk 3.50 (1.59) CNNK-64 3200 (14.23) 8" (203.2) 8" (203.2) 6 6.20 (2.81) Lbs. (kg) .40 (.18) Vibration Isolation L All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 256 Eaton Vibration Isolation VRP Type - Rubber Cube Vibration Pad Use: Is used to dampen noise and vibration in floor caused by medium and high speed equipment. • Recommended load capacity: Up to 45 lbs./sq.in. (0.038 kgf/mm2) per 1 square inch • Overall thickness: 3/4” (19.0mm) • Rated deflection is 3/16" (4.7mm). • Durable: Material is natural rubber composition VRP-4 • Each square has 4 suction holes (1/2" (12.7mm) diameter) to provide a non-skid effect. The standard VRP pad has 81 squares that are 2" x 2" (50.8mm x 50.8mm) making the pad itself 18" x 18" (457.2mm x 457.2mm). These squares are easily cut or torn to desired sizes. VRP-16 VRP-36 VRP-324 W 2” 3/4” (50.8) (19.0) 2” (50.8) VRP-324 shown L Vibration Isolation Part No. Dimensions Rated Load Lbs. L W (kN) in. (mm) in. (mm) Std. Pkg. (50.8) 2" Wt. Each Lbs. (kg) VRP-4 180 (.80) 2" (50.8) Bulk .10 (.05) VRP-16 720 (3.20) 4" (101.6) 4" (101.6) Bulk .41 (.19) VRP-36 1620 (7.20) 6" (152.4) 6" (152.4) Bulk .90 (.41) VRP-324 14580 (64.85) 18" (457.2) 18" (457.2) 3 8.15 (3.70) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 257 B-Line series Pipe Hangers & Supports Vibration Isolation BVS Type - Vibra Strip™ for 15/8" (41.3mm) wide Eaton B-Line series channel Use: Dampen noise and vibration of equipment when mounted on strut. • When inserted in channel slot, provides an excellent isolation medium between equipment, duct, piping, etc., and the support channel. • Vibra Strip is furnished in 12" (304.8mm) or 120” (3.05m) lengths, may be cut to satisfy specific requirement. BVS-12 • Durable: 45 durometer Neoprene • Temperature Range: -20°F (-28.9°C) to 212°F (100°C) (continuous) Part No. Max. Load Lbs. per Lineal In. Length (mm) Vibration Isolation BVS-120 Wt. Each Std. Pkg. Lbs. (kg) (.21) Lbs. (kg/25.4 mm) in. BVS-12 40 (18.1) 12" (304.8) 25 .46 BVS-120 40 (18.1) 120" (3048.0) 1 4.56 (2.07) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 258 Eaton Vibration Isolation RM & RM-D Type - Neoprene Mount Use: To minimize or prevent noise and vibration from transferring between equipment and floor or solid support structure. Typical applications include air handling units, air conditioners, compressors, pumps, machine tools, motors, business machines, transformers, furnaces, etc. L S K 1/4" (6.3) Deflection W O T (thread) J H Typical Part Numbering RM - 80 A 1/2" (12.7) Deflection Type RM Series for 1/4” (6.3mm) Deflection Load Mount Size RM-D Series for 1/2” (12.7mm) Deflection Part No. Mount Size Maximum Load Color Code Part No. Mount Size Maximum Load Color Code Lbs. (kN) Lbs. (kN) RM-40A RM-55A RM-80A RM-130A A A A A 40 55 80 130 (0.18) (.0.25) (0.35) (0.58) Orange Yellow Green Blue RM-D-40A RM-D-55A RM-D-80A RM-D-130A A A A A 40 55 80 130 (0.18) (.0.25) (0.35) (0.58) Orange Yellow Green Blue RM-120B RM-200B RM-280B RM-400B B B B B 120 200 280 400 (0.53) (.0.89) RM-D-120B RM-D-200B RM-D-280B RM-D-400B B B B B 120 200 280 400 (0.53) (.0.89) (1.24) (1.78) Orange Yellow Green Blue (1.24) (1.78) Orange Yellow Green Blue RM-300C RM-520C RM-750C RM-1100C C C C C 300 520 750 1100 (.1.33) (2.31) (3.33) (4.89) Yellow Green Blue White RM-D-300C RM-D-520C RM-D-750C RM-D-1100C C C C C 300 520 750 1100 (.1.33) (2.31) (3.33) (4.89) Yellow Green Blue White RM-1800F RM-3000F RM-5000F F F F 1800 (8.00) 3000 (13.3) 5000 (22.2) Green Blue Green RM-D-1800F RM-D-3000F RM-D-5000F F F F 1800 (8.00) 3000 (13.3) 5000 (22.2) Green Blue Green Dimensions Vibration Isolation L S W Mount Size in. (mm) A 33/16 (81.0) B 37/8 (98.4) C 51/2 (134.7) 41/8 (104.8) F 71/2 61/8 (155.6) 47/8 O T K H RM (190.5) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) J RM-D in. (mm) RM-D in. (mm) in. (mm) (38.1) 13/16 (20.6) 15/16 (33.3) 23/8 (27.8) 113/16 (47.5) 11/32 (8.7) 5/16”-18 11/4 (31.7) 1 (25.4) 3 (76.2) 23/8 (60.3) 11/32 (8.7) 3/8”-16 13/4 (44.4) 11/4 (31.7) 113/16 (46.0) 11/32 (26.2) 19/16 (39.7) 31/4 (82.5) 9/16 (14.3) 1/2”-13 21/2 (63.5) 11/2 (38.1) 21/2 (63.5) 11/4 (31.7) 21/4 (57.1) 9/16 (14.3) 5/8”-11 43/8 15/8 23/4 13/8 21/2 (63.5) (123.8) (111.1) (41.3) 11/2 RM (69.8) (34.9) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 259 B-Line series Pipe Hangers & Supports Vibration Isolation OS Type - Steel Spring Isolator/Restraint - 1” (25.4mm) & 2” (50.8mm) Deflection Use: To support and isolation of vibrations between equipment or frame mounted equipment and the floor or supporting structure • Neoprene pad 1/4” (6.3mm) thick under spring regardless of style • All OS Type isolator/restraints feature large diameter springs with O.D. not less than 80% of rated deflection height • Adjust load transfer while motion restraint adjustments are loose • For compact support of heavy loads, some OS’s include inner springs. For lower profile support of heavy loads when required, OSE’s have clustered springs Style V Style R Mounting Holes H diameter Style V - shown W Motion Restraint Adjustment Style R For Attachment To Side Of Equipment M 1” L (25.4) Option P Neoprene Pad Regardless Of Style Stud D diameter Typical Part Numbering OS A - R - E500 P Type Housing Size Style V or R Spring Number Neoprene Base Option Style V - OSE 4 Spring Part Numbers - E Springs - 1” (25.4mm) Deflection OSA-(*)-E21(**) OSA-(*)-E55(**) OSA-(*)-E79(**) OSA-(*)-E106(**) OSA-(*)-E143(**) OSA-(*)-E187(**) OSA-(*)-E244(**) OSA-(*)-E318(**) OSA-(*)-E415(**) OSA-(*)-E500(**) OSA-(*)-E633(**) OSA-(*)-E801(**) Housing Size B E OSB-(*)-ET255(**) OSB-(*)-ET347(**) OSB-(*)-ET473(**) OSB-(*)-E630(**) OSB-(*)-E806(**) OSB-(*)-E1030(**) OSB-(*)-E1230(**) OSB-(*)-E1430(**) OSB-(*)-E1810(**) OSB-(*)-E2210(**) Part Numbers - F Springs - 2” (50.8mm) Deflection OSE-(*)-E976(**) OSE-(*)-E1272(**) OSE-(*)-E1660(**) OSE-(*)-E2000(**) OSE-(*)-E2532(**) OSE-(*)-E3204(**) OSE-(*)-E4128(**) Housing Size (*) Insert Style V or R (**) Insert Option P when required A B E F OSA-(*)-F33(**) OSA-(*)-F43(**) OSA-(*)-F59(**) OSA-(*)-F83(**) OSA-(*)-F120(**) OSA-(*)-F155(**) OSA-(*)-F195(**) OSA-(*)-F236(**) OSA-(*)-F300(**) OSB-(*)-FT121(**) OSB-(*)-FT171(**) OSB-(*)-FT241(**) OSB-(*)-F348(**) OSB-(*)-F453(**) OSB-(*)-F590(**) OSB-(*)-F676(**) OSB-(*)-F787(**) OSB-(*)-F918(**) OSE-(*)-F332(**) OSE-(*)-F480(**) OSE-(*)-F620(**) OSE-(*)-F780(**) OSE-(*)-F944(**) OSE-(*)-F1200(**) OSF-(*)-F1159(**) OSF-(*)-F1408(**) OSF-(*)-F1710(**) OSF-(*)-F2149(**) OSF-(*)-F2700(**) (*) Insert Style V or R (**) Insert Option P when required Vibration Isolation A Dimensions Housing Size A B E F L M T W D H Approx. Oper. Height in. (mm) in. (mm) 7 (177.8) 6 101/2 (266.7) 14 14 (355.6) (355.6) (152.4) in. (mm) 23/4 (69.8) 9 (228.6) 4 (101.6) 12 (304.8) 6 (152.4) 12 (304.8) 6 (152.4) in. (mm) in. (mm) 2 (50.8) 3/8 31/2 (88.9) 1/2 (127.0) 5/8 (127.0) 5/8 5 5 in. (mm) in. (mm) (9.5) 9/16 (14.3) 41/2 (114.3) (12.7) 11/16 (17.5) 51/2 (139.7) (15.9) 11/16 (17.5) 5 (127.0) (15.9) 11/16 (17.5) 8 (203.3) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 260 Eaton Vibration Isolation OS Type - Steel Spring Isolator/Restraint - 3” (76.2mm) Deflection Use: To support and isolation of vibrations between equipment or frame mounted equipment and the floor or supporting structure. • Neoprene pad 1/4” (6.3mm) thick under spring regardless of style • All OS Type isolator/restraints feature large diameter springs with O.D. not less than 80% of rated deflection height • Adjust load transfer while motion restraint adjustments are loose • For compact support of heavy loads, some OS’s include inner springs. For lower profile support of heavy loads when required, OSE’s have clustered springs Style V - shown Mounting Holes 11/16” (17.5) diameter Motion Restraint Adjustment W M L Load Transfer Adjustment 1” Stud D diameter T Style R For Attachment To Opposite Side Of Equipment (25.4) Oper. Height Option P Neoprene Pad Regardless Of Style Style V Part Numbers - G Springs - 3” (76.2mm) Deflection Housing Size Typical Part Numbering OSB OSF OSB-(*)-3YW162(**) OSB-(*)-G213(**) OSB-(*)-G303(**) OSB-(*)-3YW325(**) OSB-(*)-3YW496(**) OSF-(*)-G853(**) OSF-(*)-3YW1036(**) OSF-(*)-G1223(**) OS B - V - G213 P Type Housing Size Style V or R Spring Number Neoprene Base Option (*) Insert Style V or R (**) Insert Option P when required Vibration Isolation Dimensions Housing Size OSB OSF L W M T D Approx. Oper. Height in. (mm) 101/2 (266.7) 14 (355.6) in. (mm) 31/2 5 (88.9) (127.0) in. (mm) in. (mm) in. (mm) in. (mm) 9 4 (101.6) 1/2 (12.7) 51/2 (139.7) (152.4) 5/8 (15.9) 8 (203.2) 12 (228.6) 6 (304.8) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 261 B-Line series Pipe Hangers & Supports Vibration Isolation JQ Type - Isolator/Restraints - 1” (25.4mm) Deflection with California Pre-Approved Seismic Protection OPA-0070 Use: To support and isolation of vibrations between equipment or frame mounted equipment and the floor or supporting structure. Pre-approved for state of California health care projects (OSHPD) Style R JQBX shown • Neoprene pad 1/4” (6.3mm) thick under spring regardless of style • All JQ Type isolator/restraints feature large diameter springs with O.D. not less than 80% of rated deflection height • Adjust load transfer while motion restraint adjustments are loose • For compact support of heavy loads, some JQ include inner springs. For lower profile support of heavy loads when required, JQE’s have clustered springs Mounting Holes 9/16” (14.3) diameter for JQA 11/16” (17.5) diameter for JQB, JQBX, JQE • Housings are HDG with Zinc Plated hardware Springs are Zinc Plated or Powder Coated W M L Motion Restraint Adjustment Load Transfer Adjustment Stud D diameter T 1” 1” (25.4) (25.4) Shear Panels JQBX only Oper. Height JQE 4 Spring Housing Style R For Attachment To Opposite Side Of Equipment JQA, JQB, & JQBX Style V Option P Neoprene Pad Regardless Of Style Style Q For Attachment To Opposite Side Of Equipment Part Numbers - E Springs - 1” (25.4mm) Deflection Housing Size JQB JQA-(*)-E21(**) JQA-(*)-E55(**) JQA-(*)-E79(**) JQA-(*)-E106(**) JQA-(*)-E143(**) JQA-(*)-E187(**) JQA-(*)-E244(**) JQA-(*)-E318(**) JQA-(*)-E415(**) JQA-(*)-E500(**) JQA-(*)-E633(**) JQA-(*)-E801(**) JQB-(*)-ET255(**) JQB-(*)-ET347(**) JQB-(*)-ET473(**) JQB-(*)-E630(**) JQB-(*)-E806(**) JQB-(*)-E1030(**) JQB-(*)-E1230(**) JQB-(*)-E1430(**) JQB-(*)-E1810(**) JQB-(*)-E2210(**) Typical Part Numbering JQBX JQE JQBX-ET255(*)(**) JQBX-ET347(*)(**) JQBX-ET473(*)(**) JQBX-E630(*)(**) JQBX-E806(*)(**) JQBX-E1030(*)(**) JQBX-E1230(*)(**) JQBX-E1430(*)(**) JQBX-E1810(*)(**) JQBX-E2210(*)(**) JQ A - R - E500 P JQE-(*)-E976(**) JQE-(*)-E1272(**) JQE-(*)-E1660(**) JQE-(*)-E2000(**) JQE-(*)-E2532(**) JQE-(*)-E3204(**) JQE-(*)-E4128(**) Type Housing Size Style V, R, or Q Spring Number Neoprene Base Option OPA-0070 – Pre-Approved Maximum Allowable Loads Housing Size Horizontal Lbs. (kN) Lbs. (kN) JQA JQB JQBX JQE 800 1000 1500 3200 (3.56) 1660 1600 2000 4300 (7.38) (*) Insert Style V, R, or Q (**) Insert Option P when required (4.45) (6.67) (14.23) Vertical (7.11) (8.89) (19.12) Vibration Isolation JQA Dimensions Housing Size L JQB/JQBX JQE M T D Approx. Oper. Height in. JQA W 7 (mm) (177.8) 101/2 (266.7) 14 (355.6) in. 2 (mm) in. (mm) 6 (50.8) 31/2 (88.9) 5 9 (127.0) 12 (152.4) (228.6) (304.8) in. (mm) 23/4 (69.8) 4 6 in. (mm) 3/8 (9.5) in. (mm) 41/2 (114.3) (101.6) 1/2 (12.7) 51/2 (139.7) (152.4) 5/8 (15.9) 5 (127.0) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 262 Eaton Vibration Isolation JQ Type - Isolator/Restraints - 2” (50.8mm) Deflection with California Pre-Approved Seismic Protection OPA-0070 Use: To support and isolation of vibrations between equipment or frame mounted equipment and the floor or supporting structure. Pre-approved for state of California health care projects (OSHPD) Front and Rear Shear Panels JQBX only • Neoprene pad 1/4” (6.3mm) thick under spring regardless of style Style R JQBX shown • All JQ Type isolator/restraints feature large diameter springs with O.D. not less than 80% of rated deflection height • Adjust load transfer while motion restraint adjustments are loose Mounting Holes 9/16” (14.3) diameter for JQA 11/16” (17.5) diameter for JQB, JQBX, JQE, JQF • For compact support of heavy loads, some JQ include inner springs. For lower profile support of heavy loads when required, JQE’s have clustered springs Style R For Attachment To Side Of Equipment W • Housings are HDG with Zinc Plated hardware Springs are Zinc Plated or Powder Coated M 1” (25.4) L Motion Restraint Adjustment Stud D diameter T Option P Neoprene Pad Regardless Of Style Oper. Height JQE 4 Spring Housing JQA, JQB, JQBX, JQE, & JQF Style V Typical Part Numbering Part Numbers - F Springs - 2” (50.8mm) Deflection JQ A - R - F236 P Housing Size JQB*** JQA JQA-(*)-F33(**) JQA-(*)-F43(**) JQA-(*)-F59(**) JQA-(*)-F83(**) JQA-(*)-F120(**) JQA-(*)-F155(**) JQA-(*)-F195(**) JQA-(*)-F236(**) JQA-(*)-F300(**) JQB_-(*)-FT121(**) JQB_-(*)-FT171(**) JQB_-(*)-FT241(**) JQB_-(*)-F348(**) JQB_-(*)-F453(**) JQB_-(*)-F590(**) JQB_-(*)-F676(**) JQB_-(*)-F787(**) JQB_-(*)-F918(**) JQE JQF JQE_-(*)-F332(**) JQE_-(*)-F480(**) JQE_-(*)-F620(**) JQE_-(*)-F780(**) JQE_-(*)-F944(**) JQE_-(*)-F1200(**) JQF-(*)-F1159(**) JQF-(*)-F1408(**) JQF-(*)-F1710(**) JQF-(*)-F2149(**) JQF-(*)-F2700(**) Type Housing Size Style V or R Spring Number Neoprene Base Option OPA-0070 – Pre-Approved Maximum Allowable Loads Housing Size Horizontal Lbs. (kN) Lbs. (kN) JQA JQB JQBX JQE JQF 800 1000 1500 3200 2900 (3.56) 1660 1600 2000 4300 4000 (7.38) (*) Insert Style V or R (**) Insert Option P when required *** Leave blank for JQB style or insert X in part number for JQBX style (4.45) (6.67) (14.23) Vibration Isolation (12.90) Vertical (7.11) (8.89) (19.12) (17.79) Dimensions Housing Size L JQB/JQBX M T D Approx. Oper. Height in. JQA W (mm) in. (mm) in. (mm) 7 (177.8) 2 (50.8) 6 (152.4) 101/2 (266.7) 31/2 (88.9) 9 (228.6) in. (mm) 23/4 (69.8) 4 in. (mm) 3/8 (9.5) in. (mm) 41/2 (114.3) (101.6) 1/2 (12.7) 51/2 (139.7) 5 (127.0) 8 (203.2) JQE 14 (355.6) 5 (127.0) 12 (304.8) 6 (152.4) 5/8 (15.9) JQF 14 (355.6) 5 (127.0) 12 (304.8) 6 (152.4) 5/8 (15.9) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 263 B-Line series Pipe Hangers & Supports Vibration Isolation JQ Type - Isolator/Restraints - 3” (76.2mm) Deflection with California Pre-Approved Seismic Protection OPA-0070 Use: For compact support or low profile support of heavy loads. Pre-approved for state of California health care projects (OSHPD) • Neoprene pad 1/4” (6.3mm) thick under spring regardless of style Style R JQBX shown • All JQ Type isolator/restraints feature large diameter springs with O.D. not less than 80% of rated deflection height • Adjust load transfer while motion restraint adjustments are loose Load Transfer Adjustment • Housings are HDG with Zinc Plated hardware Springs are Zinc Plated or Powder Coated Mounting Holes 11/16” (17.5) diameter for JQB, JQBX, JQF Style R For Attachment To Opposite Side Of Equipment W Load Transfer Adjustment Stud D diameter T M Style Q For Attachment To Opposite Side Of Equipment 1” (25.4) 1” (25.4) L Shear Panels JQBX only Oper. Height JQB, JQBX, & JQF Option P Neoprene Pad Regardless Of Style Style V Part Numbers - G Springs - 3” (76.2mm) Deflection Housing Size JQBX JQB-(*)-3YW162(**) JQB-(*)-G213(**) JQB-(*)-G303(**) JQB-(*)-3YW325(**) JQB-(*)-3YW496(**) Typical Part Numbering JQF JQ B - V - G213 P JQBX-(*)-3YW162(**) JQF-(*)-G853(**) JQBX-(*)-G213(**) JQF-(*)-3YW1036(**) JQBX-(*)-G303(**) JQF-(*)-G1223(**) JQBX-(*)-3YW325(**) JQBX-(*)-3YW496(**) Type Housing Size Style V, R, or Q Spring Number Neoprene Base Option (*) Insert Style V, R, or Q (**) Insert Option P when required OPA-0070 – Pre-Approved Maximum Allowable Loads Housing Size Horizontal JQB JQBX JQF 1000 (4.45) 1500 (6.67) 2900 (12.90) Lbs. (kN) Vertical Lbs. (kN) 1600 (7.11) 2000 (8.89) 4000 (17.79) Vibration Isolation JQB Dimensions Housing Size L JQF M T D Approx. Oper. Height in. JQB/JQBX W (mm) 101/2 (266.7) 14 (355.6) in. (mm) in. (mm) 31/2 (88.9) 5 (127.0) in. (mm) in. (mm) 9 (228.6) 4 (101.6) 1/2 (12.7) 12 (304.8) 6 (152.4) 5/8 (15.9) in. (mm) 51/2 (139.7) 8 (203.2) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 264 Eaton Vibration Isolation JQ-TQN Type - Top Quality Neoprene Isolator/Restraints - 1/2” (12.7mm) Deflection with California Pre-Approved Seismic Protection OPA-0070 Use: For support of light equipment or framed equipment and isolation with a cushion to prevent vibration transference to structure. Pre-approved for state of California health care projects (OSHPD) • Adjust load transfer while motion restraint adjustments are loose • Housings are HDG with Zinc Plated hardware Style R Style V JQBX TQN 520 Style R shown JQAM TQN 55 Style V shown JQE TQN 4200 Style V shown R Style Panel Panel Panels JQB JQBX Mounting Holes No Yes Load Transfer Nut 9/16” (14.3) diameter for AM 11/16” (17.5) diameter for B, BX, E Seismic Restraint Adjustment W F Stud D diameter Oper. Height M L TQN Top Quality Neoprene Vibration Isolation Load Transfer Styles Style V Style R All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 265 B-Line series Pipe Hangers & Supports Vibration Isolation JQ-TQN Type - Top Quality Neoprene Isolator/Restraints - 1/2” (12.7mm) Deflection con’t. with California Pre-Approved Seismic Protection OPA-0070 1/2” (12.7mm) Rated Static Deflection Part No. Maximum Load Color Code Typical Part Numbering in. (mm) JQAMTQN-(*)-40 JQAMTQN-(*)-55 JQAMTQN-(*)-80 JQAMTQN-(*)-120 JQAMTQN-(*)-200 JQAMTQN-(*)-280 JQAMTQN-(*)-400 40 55 80 120 200 280 400 (0.18) (.0.25) (0.35) (0.53) (.0.89) (1.24) (1.78) Yellow Green Blue Orange Yellow Green Blue JQBTQN-(*)-300 JQBTQN-(*)-520 JQBTQN-(*)-750 JQBTQN-(*)-1100 300 520 750 1100 (1.33) (2.31) (3.33) (4.89) Yellow Green Blue White JQBXTQN-(*)-300 JQBXTQN-(*)-520 JQBXTQN-(*)-750 JQBXTQN-(*)-1100 JQETQN-(*)-1800 JQETQN-(*)-3000 JQETQN-(*)-5000 300 520 750 1100 JQ AM TQN - V - 200 Type Housing Size TQN Isolator Style V or R Load Rating OPA-0070 – Pre-Approved Maximum Allowable Loads Yellow Green Blue White (1.33) (2.31) (3.33) (4.89) Green Blue White 1800 (8.00) 3000 (13.34) 5000 (22.24) Housing Size Horizontal Lbs. (kN) AM B BX E 600 1000 1500 3200 (2.67) (4.45) (6.67) (14.23) Vertical Lbs. (kN) 900 (4.00) 1600 (7.11) 2000 (8.89) 4300 (109.22) (*) Insert Style V or R Dimensions Housing Size L B / BX F D Approx. (mm) in. (mm) in. (mm) 7 (177.8) 2 (50.8) 6 (152.4) 101/2 (266.7) 31/2 (88.9) 9 (228.6) 14 (355.6) 5 (127.0) 12 (304.8) in. (mm) 23/4 (69.8) 4 6 in. (mm) 3/8 (9.5) in. (mm) 23/4 (69.8) (101.6) 1/2 (12.7) 5 (127.0) (152.4) 5/8 (15.9) 5 (127.0) Vibration Isolation E M Oper. Height in. AM W All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 266 Eaton Vibration Isolation RQ & RQD Type - Neoprene Mount with Integrak Seismic Restraints Use: For support of light equipment or framed light equipment while preventing transfer of vibration to structure R - Rod Size Neoprene Washer RQ B C D RQD No Metal To Metal Contact H A J Typical Part Numbering L RQ - A130 Type Mount Number 1/4” (6.3mm) Maximum Deflection Part No. 1/2” (12.7mm) Maximum Deflection Maximum Load Color Code Lbs. (kN) RQ-A40 RQ-A55 RQ-A80 RQ-A130 40 55 80 130 (0.18) (.0.25) (0.35) (0.58) Orange Yellow Green Blue RQ-B120 RQ-B200 RQ-B280 RQ-B400 120 200 280 400 (0.53) (0.89) (1.24) (1.678) RQ-C300 RQ-C520 RQ-C750 RQ-C1100 300 520 750 1100 (1.33) (2.31) (3.33) (4.89) Part No. Maximum Load Color Code Lbs. (kN) RQD-A40 RQD-A55 RQD-A80 RQD-A130 40 55 80 130 (0.18) (.0.25) (0.35) (0.58) Orange Yellow Green Blue Orange Yellow Green Blue RQD-B120 RQD-B200 RQD-B280 RQD-B400 120 200 280 400 (0.53) (0.89) (1.24) (1.678) Orange Yellow Green Blue Yellow Green Blue White RQD-C300 RQD-C520 RQD-C750 RQD-C1100 300 520 750 1100 (1.33) (2.31) (3.33) (4.89) Yellow Green Blue White Dimensions Neoprene Type A in. (mm) B C D L in. (mm) in. (mm) in. (mm) in. (mm) 41/2 (114.3) J R in. (mm) H in. (mm) Vibration Isolation RQ-A 31/2 (88.9) 2 (50.8) 1 (25.4) 7/16 (11.1) 1 (25.4) 3/8”-16 2 (50.8) RQ-B 45/16 (109.5) 21/2 (63.5) 11/4 (31.7) 9/16 (14.3) 53/8 (136.5) 11/2 (38.1) 5/8”-11 23/4 (69.8) RQ-C 5 (127.0) 31/4 (82.5) 15/8 (41.3) 11/16 (17.5) 63/16 (157.2) 17/8 (47.6) 3/4”-10 33/8 (85.7) 41/2 (114.3) RQD-A 31/2 (88.9) 2 (50.8) 1 (25.4) 7/16 (11.1) 1 (25.4) 3/8”-16 2 (50.8) RQD-B 45/16 (109.5) 21/2 (63.5) 11/4 (31.7) 9/16 (14.3) 53/8 (136.5) 11/2 (38.1) 5/8”-11 23/4 (69.8) RQD-C 5 (127.0) 31/4 (82.5) 15/8 (41.3) 11/16 (17.5) 63/16 (157.2) 17/8 (47.6) 3/4”-10 33/8 (85.7) Type RQ: Single Deflection (1/4” (6.3mm) Maximum) Type RQD: Double Deflection (1/2” (12.7mm) Maximum) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 267 B-Line series Pipe Hangers & Supports Vibration Isolation Reference Tables For use in selecting hangers for standard pipe Nominal Pipe Size in. (mm) 3/4 (20) 1 (25) 11/4 (32) 11/2 (40) 2 (50) 21/2 (65) 3 31/2 4 41/2 5 6 7 8 9 10 12 (80) (90) (100) (115) (125) (150) (175) (200) (225) (250) (300) Weight Per Foot (25.4mm) Standard Pipe Dry or Steam Water Filled Filled Hanger Selection Load 10’ (3.05m) Spacing lbs. (kg) lbs. (kg) lbs. (kN) 1.13 1.68 2.28 2.73 3.68 5.82 7.62 9.20 10.89 12.64 14.81 19.18 24.05 28.60 33.90 40.50 49.60 (0.51) (0.76) (1.03) (1.24) (1.67) (2.64) 1.36 2.06 2.93 3.62 5.15 7.91 10.85 13.52 16.45 19.50 23.55 31.80 40.85 50.50 61.10 75.00 99.00 (0.61) (0.93) (1.33) (1.64) (2.33) (3.59) 21 55 55 55 79 143 143 187 244 244 318 415 500 715 1060 1060 1430 (0.09) (024) (024) (024) (0.35) (0.63) (3.45) (4.17) (4.94) (5.73) (6.72) (8.70) (10.91) (12.97) (15.38) (18.37) (22.50) (4.92) (6.13) (7.46) (8.84) (10.68) (14.42) (18.53) (22.90) (27.71) (24.02) (44.90) (0.63) (0.83) (1.08) (1.08) (1.41) (1.84) (2.22) (3.18) (4.71) (4.71) (6.36) Selection based on water filled pipe only. Add weight of fittings if any and reselect. 125# Cast Iron pipe fitting approximate weights Strainer Check Valve Gate Valve Elbow Tee Flange in. (mm) lbs. (kg) lbs. (kg) lbs (kg) lbs (kg) lbs (kg) lbs (kg) 11/2 (40) (50) (65) (80) (100) (125) (150) (200) (250) (300) 20 30 40 50 85 110 140 205 330 440 (9.1) (13.6) (18.1) (22.7) (38.5) (49.9) (63.5) (93.0) (149.7) (199.6) 25 25 35 45 80 120 155 305 455 675 (11.3) (11.3) (15.9) (20.4) (36.3) (54.4) (70.3) (138.3) (206.4) (306.2) 30 40 50 70 110 140 415 250 475 690 (13.6) (18.1) (22.7) (31.7) (49.9) (63.5) (1.84) (113.4) (215.4) (313.0) 15 20 25 30 55 70 90 120 245 375 (6.8) (9.1) (11.3) (13.6) (24.9) (31.7) (40.8) (54.4) (111.1) (54.4) 20 25 35 40 70 90 115 175 295 405 (9.1) (11.3) (15.9) (18.1) (31.7) (40.8) (52.1) (79.4) (133.8) (183.7) 3.5 6 8 9 16 20 25 34 53 71 (1.6) (2.7) (3.6) (4.1) (7.2) (9.1) (11.3) (15.4) (24.0) (32.2) 2 21/2 3 4 5 6 8 10 12 Vibration Isolation Nominal Pipe Size For 250# fittings, multiply above values by 1.8. All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 268 Eaton Vibration Isolation RH & RHD Type - Neoprene Hanger Use: Used to dampen noise and vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems. • • • • • 1”-8 MRD RHD-E *Type RH: Single deflection - 1/4” (6.3mm) maximum **Type RHD: Double deflection - 1/2” (12.7mm) maximum MRD is maximum rod diameter Housing finish: Zinc Plated Threaded rods, nuts, and washers are furnished separately shown 63/8” (161.9) 3/4”-10 RHD-B MRD shown 43/4” (120.6) C5x6.7# *11/4” (31.7) **13/4” (44.4) 51/2” 6” (139.7) (152.4) RH Type 23/4” 21/2” (69.8) (63.5) RHD Type 3/8”-16 MRD 7/8”-9 RH-A & RHD-A RH-C & RHD-C MRD shown shown *1” *11/2” (25.4) (38.1) 51/4” 31/4” (82.5) **11/2” (38.1) (63.5) 21/2” 13/4” (63.5) (44.4) 33/4” Vibration Isolation RH-40-A RH-55-A RH-80-A RH-130-A RH-120-B RH-200-B RH-280-B RH-400-B RH-300-C RH-520-C RH-750-C RH-1100-C Eaton Maximum Load lbs. (kN) 40 55 80 130 120 200 280 400 300 520 750 1100 (0.09) (0.24) (0.35) (0.47) (0.53) (0.69) (0.83) (1.08) (1.41) (1.75) (2.27) (31.8) (76.2) 1/2” (12.7mm) Maximum Double Deflection Color Code Yellow Green Blue White Orange Yellow Green Blue Yellow Green Blue White 3” (95.2) 1/4” (6.3mm) Maximum Single Deflection Part Number (133.1) **21/2” Part Number Typical Part Numbering RH - 280 - B Type Load Rating Size 269 RHD-40-A RHD-55-A RHD-80-A RHD-130-A RHD-120-B RHD-200-B RHD-280-B RHD-400-B RHD-300-C RHD-520-C RHD-750-C RHD-1100-C RHD-1700-E RHD-2700-E RHD-4200-E Maximum Load lbs. (kN) 40 55 80 130 120 200 280 400 300 520 750 1100 1700 2700 4200 (0.09) (0.24) (0.35) (0.47) (0.53) (0.69) (0.83) (1.08) (1.41) (1.75) (2.27) (31.8) (4.71) (6.76) (8.72) Color Code Yellow Green Blue White Orange Yellow Green Blue Yellow Green Blue White Green Blue White B-Line series Pipe Hangers & Supports Vibration Isolation CHSCS Type - Spring Hanger with Seismic Cushion Stop - 1” (25.4mm) Deflection Use: Used to dampen noise and vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems. • All housing sizes have been tested to carry five times the maximum load without failure • Spring rated deflection is 1” (25.4mm) • SFH = Free Height • Threaded rod, nuts, and washers supplied separately • * Housings are specially reinforced for extra strength *Extra Strength Hanger CHSCS-E1580 thru CHSCS-E2860 Basic Hanger CHSCS-E500 thru CHSCS-E1060 Light Weight Hanger CHSCS-E21 thru CHSCS-E415 Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion W L Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion W Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion L S S S L W D Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate D Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate D Dimensions Part Number CHSCS - E143 Type Load CHSCS-E21 CHSCS-E55 CHSCS-E79 CHSCS-E106 CHSCS-E143 CHSCS-E187 CHSCS-E244 CHSCS-E318 CHSCS-E415 CHSCS-E500 CHSCS-715 CHSCS-1060 CHSCS-1430 * CHSCS-2120 * CHSCS-2860 * Maximum Load SFH S W L lbs. (kN) in. (mm) in. (mm) in. (mm) in. (mm) 21 55 79 106 143 187 244 318 415 500 715 1060 1430 2120 2860 (0.09) 25/8 23/4 25/8 25/8 25/8 25/8 23/4 31/8 31/16 31/4 41/4 41/4 41/4 41/4 41/4 (66.7) 43/4 43/4 43/4 43/4 43/4 43/4 43/4 43/4 43/4 71/2 71/2 71/2 83/8 83/8 83/8 (120.6) 23/4 23/4 23/4 23/4 23/4 23/4 23/4 23/4 23/4 31/4 31/4 31/4 6 6 6 (69.8) 21/2 21/2 21/2 21/2 21/2 21/2 21/2 21/2 21/2 23/4 23/4 23/4 6 6 6 (63.5) (0.24) (0.35) (0.47) (0.63) (0.83) (1.08) (1.41) (1.84) (2.22) (3.18) (4.71) (6.36) (9.43) (12.72) (69.8) (66.7) (66.7) (66.7) (66.7) (69.8) (79.4) (77.8) (82.5) (107.9) (107.9) (107.9) (107.9) (107.9) (120.6) (120.6) (120.6) (120.6) (120.6) (120.6) (120.6) (120.6) (190.5) (190.5) (190.5) (212.7) (212.7) (212.7) (69.8) (69.8) (69.8) (69.8) (69.8) (69.8) (69.8) (69.8) (82.5) (82.5) (82.5) (152.4) (152.4) (152.4) (63.5) (63.5) (63.5) (63.5) (63.5) (63.5) (63.5) (63.5) (69.8) (69.8) (69.8) (152.4) (152.4) (152.4) SCS Diameter D Diameter in. (mm) 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 3 3 3 3 3 3 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 5/8”-11 (60.3) 5/8”-11 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 270 Eaton Vibration Isolation Typical Part Numbering Vibration Isolation CHSCS Type - Spring Hanger with Seismic Cushion Stop - 2” (50.8mm) Deflection Use: Used to dampen noise and vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems. • All housing sizes have been tested to carry five times the maximum load without failure • Spring rated deflection is 2” (50.8mm) • SFH = Free Height *Extra Strength Hanger CHSCS-F1159 thru CHSCS-F3420 • Threaded rod, nuts, and washers supplied separately • * Housings are specially reinforced for extra strength Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion Basic Hanger CHSCS-F59 thru CHSCS-F918 L Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion W S S D D Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate L W Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate Dimensions Typical Part Numbering Part Number CHSCS - F120 Type Load Vibration Isolation CHSCS-F59 CHSCS-F83 CHSCS-F120 CHSCS-F155 CHSCS-F195 CHSCS-F241 CHSCS-F348 CHSCS-F453 CHSCS-F590 CHSCS-F676 CHSCS-F787 CHSCS-F918 CHSCS-F1159 * CHSCS-F1408 * CHSCS-F1710 * CHSCS-F2318 * CHSCS-F2816 * CHSCS-F3420 * Maximum Load SFH lbs. (kN) in. (mm) 59 83 120 155 195 241 348 453 590 676 787 918 1159 1408 1710 2318 2816 3420 (0.26) 41/4 41/4 41/4 41/4 49/16 41/2 5 5 5 5 5 5 67/16 67/16 67/16 67/16 67/16 67/16 (107.9) (0.37) (0.53) (0.69) (0.87) (1.07) (1.55) (2.01) (2.62) (3.00) (3.50) (4.08) (5.15) (6.26) (7.60) (10.31) (12.52) (15.21) (107.9) (107.9) (107.9) (115.9) (114.3) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (163.5) (163.5) (163.5) (163.5) (163.5) (163.5) S in. (mm) 9 (228.6) 9 (228.6) 9 (228.6) 9 (228.6) 9 (228.6) 10 (254.0) 10 (254.0) 10 (254.0) 11 (279.4) 11 (279.4) 11 (279.4) 11 (279.4) 11 (279.4) 11 (279.4) 11 (279.4) 111/4 (285.7) 111/4 (285.7) 111/4 (285.7) W L in. (mm) in. (mm) 3 3 3 3 3 51/2 51/2 51/2 51/4 51/4 51/4 51/4 6 6 6 11 11 11 (76.2) 21/2 21/2 21/2 21/2 21/2 41/2 41/2 41/2 41/2 41/2 41/2 41/2 5 5 5 5 5 5 (63.5) (76.2) (76.2) (76.2) (76.2) (139.7) (139.7) (139.7) (133.3) (133.3) (133.3) (133.3) (152.9) (152.9) (152.9) (279.4) (279.4) (279.4) (63.5) (63.5) (63.5) (63.5) (114.3) (114.3) (114.3) (114.3) (114.3) (114.3) (114.3) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) SCS Diameter D Diameter in. (mm) 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 3 3 3 3 3 3 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 5/8”-11 (60.3) 5/8”-11 (60.3) 3/4”-10 (60.3) 3/4”-10 (60.3) 3/4”-10 (60.3) 3/4”-10 (76.2) 3/4”-10 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 271 B-Line series Pipe Hangers & Supports Vibration Isolation CH30SCS Type - 15° Tilt, 1” (25.4mm) Deflection Combination Hanger - Spring & Neoprene with Seismic Cushion Stop Use: Used to dampen noise and minor vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems.Used where uncertain alignment is anticipated during installation. At rated load the hanger rod will operate to a full 15° tilt in any direction from vertical centerline. • All housing sizes have been tested to carry five times the maximum load without failure *Extra Strength Hanger CH30SCS-E1612 thru CH30SCS-E4920 • Spring rated deflection is 1” (25.4mm) SCS (T) • SFH = Free Height • Threaded rod, nuts, and washers supplied separately • * Housings are specially reinforced for extra strength Light Weight Hanger CH30SCS-ET20 thru CH30SCS-ET255 SCS (T) Basic Hanger CH30SCS-ET347 thru CH30SCS-ET1326 S SCS (T) See Neoprene Sleeve Detail S See Neoprene Sleeve Detail S SCS (B) SCS (B) W L D L L SCS (B) W Spring Channel W D D Typical Part Numbering Spring Hanger Rod Vertical Centerline Steel Washer Neoprene Sleeve CH30SCS - ET129 Hanger Rod Vertical Centerline Neoprene Sleeve Detail Neoprene Sleeve Type Load Neoprene Sleeve Detail Dimensions SCS (T) = Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion SCS (B) = Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate CH30SCS-ET20 CH30SCS-ET42 CH30SCS-ET80 CH30SCS-ET129 CH30SCS-ET194 CH30SCS-ET255 CH30SCS-ET347 CH30SCS-ET473 CH30SCS-ET667 CH30SCS-ET940 CH30SCS-ET1326 CH30SCS-E1612 * CH30SCS-E2060 * CH30SCS-E2460 * CH30SCS-E2980 * CH30SCS-E4120 * CH30SCS-E4920 * Maximum Load lbs. (kN) 20 42 80 129 194 255 347 473 667 940 1326 1612 2060 2460 2980 4120 4920 (0.09) (0.18) (0.35) (0.57) (0.86) (1.13) (1.54) (2.10) (2.96) (4.18) (5.90) (7.17) (9.16) (10.94) (13.25) (18.32) (21.88) SFH in. (mm) 17/8 2 21/8 23/8 23/8 21/2 23/4 27/8 31/8 33/8 35/8 35/8 37/8 41/8 41/8 37/8 41/8 (47.6) (50.8) (54.0) (60.3) (60.3) (63.5) (69.8) (73.0) (79.4) (85.7) (92.1) (92.1) (98.4) (104.8) (104.8) (98.4) (104.8) S in. (mm) 43/4 43/4 43/4 43/4 43/4 43/4 6 6 7 7 7 81/4 81/4 81/4 81/4 81/2 81/2 (120.6) (120.6) (120.6) (120.6) (120.6) (120.6) (152.9) (152.9) (177.8) (177.8) (177.8) (209.5) (209.5) (209.5) (209.5) (215.9) (215.9) W in. (mm) 35/8 (92.1) 35/8 (92.1) 35/8 (92.1) 35/8 (92.1) 35/8 (92.1) 35/8 (92.1) 55/16 (134.9) 55/16 (134.9) 57/8 (149.2) 57/8 (149.2) 57/8 (149.2) 10 (254.0) 10 (254.0) 10 (254.0) 10 (254.0) 91/2 (241.3) 91/2 (241.3) L in. (mm) 21/2 21/2 21/2 21/2 21/2 21/2 41/4 41/4 43/4 43/4 43/4 4 4 4 4 7 7 (63.5) (63.5) (63.5) (63.5) (63.5) (63.5) (107.9) (107.9) (120.6) (120.6) (120.6) (101.6) (101.6) (101.6) (101.6) (177.8) (177.8) SCS Diameter D Diameter in. (mm) 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 3 3 3 3 3 3 3 4 4 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 5/8”-11 (60.3) (76.2) 5/8”-11 3/4”-10 (76.2) 3/4”-10 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 1”-8 1”-8 1”-8 11/8”-7 11/8”-7 (76.2) (76.2) (101.6) (101.6) Vibration Isolation Part Number All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 272 Eaton Vibration Isolation CH30SCS Type - 15° Tilt, 2” (50.8mm) Deflection Spring Hanger with Seismic Cushion Stop Use: Used to dampen noise and minor vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems.Used where uncertain alignment is anticipated during installation. At rated load the hanger rod will operate to a full 15° tilt in any direction from vertical centerline. • All housing sizes have been tested to carry five times the maximum load without failure *Extra Strength Hanger CH30SCS-F696 thru CH30SCS-F3420 SCS (T) • Spring rated deflection is 1” (25.4mm) • SFH = Free Height • Threaded rod, nuts, and washers supplied separately • * Housings are specially reinforced for extra strength Basic Hanger CH30SCS-FT30 thru CH30SCS-F590 SCS (T) S SCS (B) S See Neoprene Sleeve Detail L See Neoprene Sleeve Detail W L SCS (B) D W Spring D Channel Typical Part Numbering Spring Hanger Rod Vertical Centerline CH30SCS - FT121 Steel Washer Neoprene Sleeve Hanger Rod Vertical Centerline Type Load Neoprene Sleeve Detail Neoprene Sleeve Neoprene Sleeve Detail Dimensions Part Number Maximum Load lbs. SCS (T) = Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion SCS (B) = Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate Vibration Isolation CH30SCS-FT30 CH30SCS-FT41 CH30SCS-FT60 CH30SCS-FT85 CH30SCS-FT121 CH30SCS-FT171 CH30SCS-FT241 CH30SCS-F348 CH30SCS-F453 CH30SCS-F590 CH30SCS-F696 * CH30SCS-F906 * CH30SCS-F1180 * CH30SCS-F1352 * CH30SCS-F1574 * CH30SCS-F1836 * CH30SCS-F2318 * CH30SCS-F2816 * CH30SCS-F3420 * 30 41 60 85 121 171 241 348 453 590 696 906 1180 1352 1574 1836 2318 2816 3420 SFH S W L SCS Diameter (kN) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) (0.13) 31/2 (88.9) 31/2 (88.9) 61/2 (165.1) 61/2 (165.1) 35/8 (92.1) 35/8 (92.1) 21/2 (63.5) 21/2 (63.5) 33/4 (95.2) 33/4 (95.2) 61/2 (165.1) 61/2 (165.1) 35/8 (92.1) 35/8 (92.1) 21/2 (63.5) 21/2 (63.5) 4 (101.6) 41/4 (107.9) 41/2 (114.3) 8 (203.2) 8 (203.2) 8 (203.2) 8 (203.2) 8 (203.2) 8 (203.2) 9 (228.6) 9 (228.6) 9 (228.6) 9 (228.6) 9 (228.6) 9 (228.6) 111/2 (292.1) 111/2 (292.1) 111/2 (292.1) 5 (127.0) 51/4 (133.3) 51/4 (133.3) 4 (101.6) 41/2 (114.3) 41/2 (114.3) 51/4 (133.3) 51/4 (133.3) 41/2 (114.3) 41/2 (114.3) 51/4 (133.3) 103/8 (263.5) 41/2 (114.3) 103/8 (263.5) (101.6) (0.18) (0.26) (0.38) (0.54) (0.76) (1.07) (1.55) (2.01) (2.62) (3.09) (4.03) (5.25) (6.01) (7.00) (8.16) (10.31) (12.52) (15.21) 5 5 5 5 5 5 5 5 5 61/2 61/2 61/2 (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (165.1) (165.1) (165.1) 103/8 (263.5) 103/8 (263.5) 103/8 (263.5) 103/8 (263.5) 123/8 (314.3) 123/8 (314.3) 123/8 (314.3) 4 4 4 4 4 4 5 5 5 (101.6) (101.6) (101.6) (101.6) (101.6) (127.0) (127.0) (127.0) 23/8 23/8 23/8 23/8 23/8 3 3 3 3 3 3 3 3 3 3 3 4 4 4 D Diameter (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) (76.2) 1/2”-13 1/2”-13 (76.2) 1/2”-13 (76.2) 5/8”-11 (76.2) 5/8”-11 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 (101.6) 7/8”-9 (101.6) 7/8”-9 (101.6) 7/8”-9 All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 273 B-Line series Pipe Hangers & Supports Vibration Isolation HHSCS Type - Combination Hanger Spring & Neoprene with Seismic Cushion Stop 11/2” (38.1mm) Deflection Use: Used to dampen noise and minor vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems.Used where uncertain alignment is anticipated during installation. At rated load the hanger rod will operate to a full 15° tilt in any direction from vertical centerline. • All housing sizes have been tested to carry five times the maximum load without failure *Extra Strength Hanger HHSCS-E1580 thru HHSCS-E2860 • Spring rated deflection is 2” (50.8mm) + neoprene rated deflection is 1/2” (12.7mm) = 21/2” (63.5mm) • SFH = Free Height Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion NFH = Neoprene Free Height • Threaded rod, nuts, and washers supplied separately • * Housings are specially reinforced for extra strength • Minimum additional travel is 50% of rated deflection at rated load S Basic Hanger HHSCS-E21 thru HHSCS-E1060 W L Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion Deflection Indicator Option I W L S Deflection Indicator Option I Pre-Compression Plate, Rod, Nuts, and Washers Option R D Typical Part Numbering HHSCS E106 R I Pre-Compression Plate, Rod, Nuts, and Washers Option R Type Spring Load Pre-Compression Option Deflector Indicator Option D Dimensions Maximum Load lbs. HHSCS-E21-R I HHSCS-E55-R I HHSCS-E79-R I HHSCS-E106-R I HHSCS-E143-R I HHSCS-E187-R I HHSCS-E244-R I HHSCS-E318-R I HHSCS-E415-R I HHSCS-E500-R I HHSCS-715-R I HHSCS-1060-R I HHSCS-1430-R I * HHSCS-2120-R I * HHSCS-2860-R I * 21 55 79 106 143 187 244 318 415 500 715 1060 1430 2120 2860 (kN) SFH (mm) in. (mm) 35/8 (92.1) 35/8 (92.1) 21/2 (63.5) 21/2 (63.5) 25/8 (66.7) 25/8 (66.7) 11/2 (38.1) 11/2 (38.1) 61/2 (165.1) 61/2 (165.1) 35/8 (92.1) 35/8 (92.1) 21/2 (63.5) 21/2 (63.5) 25/8 (66.7) 25/8 (66.7) 11/2 (38.1) 13/4 (44.4) 61/2 (165.1) 71/2 (190.5) 35/8 (92.1) 31/4 (82.5) 21/2 (63.5) 23/4 (69.8) 23/4 (69.8) 31/8 (79.4) 13/4 (44.4) 13/4 (44.4) 71/2 (190.5) 71/2 (190.5) 31/4 (82.5) 31/4 (82.5) 23/4 (69.8) 23/4 (69.8) 31/16 (77.8) 31/4 (82.5) 13/4 (44.4) 21/2 (63.5) 71/2 (190.5) 93/4 (247.6) 31/4 (82.5) 37/8 (98.4) 23/4 (69.8) 31/4 (82.5) 41/4 (107.9) 41/4 (107.9) 21/2 (63.5) 21/2 (63.5) 93/4 (247.6) 93/4 (247.6) 37/8 (98.4) 37/8 (98.4) 31/4 (82.5) 31/4 (82.5) 23/4 (69.8) 23/4 (69.8) 113/8 (289.9) (9.43) 41/4 (107.9) 41/4 (107.9) 113/8 (289.9) 61/2 (165.1) 61/2 (165.1) (12.72) 41/4 (107.9) 23/4 (69.8) 113/8 (289.9) 61/2 (165.1) (0.47) (0.63) (0.83) (1.08) (1.41) (1.84) (2.22) (3.18) (4.71) (6.36) (mm) in. L 61/2 (165.1) 61/2 (165.1) (0.35) in. W 11/2 (38.1) 11/2 (38.1) (0.24) (mm) S 25/8 (66.7) 23/4 (69.8) (0.09) in. NFH in. 6 6 6 SCS Diameter D Diameter (mm) (152.4) (152.4) (152.4) 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 3 3 3 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 5/8”-11 (60.3) 5/8”-11 (60.3) 3/4”-10 (60.3) 3/4”-10 (60.3) 3/4”-10 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 Vibration Isolation Part Number Insert R for Option R (Pre-Compression Hardware) when required and I for Option I (deflection indicator) when required All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 274 Eaton Vibration Isolation HHSCS Type - Combination Hanger Spring & Neoprene with Seismic Cushion Stop 21/2” (63.5mm) Deflection Use: Used to dampen noise and minor vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems.Used where uncertain alignment is anticipated during installation. At rated load the hanger rod will operate to a full 15° tilt in any direction from vertical centerline. • All housing sizes have been tested to carry five times the maximum load without failure *Extra Strength Hanger HHSCS-F1159 thru HHSCS-F3420 • Spring rated deflection is 2” (50.8mm) + neoprene rated deflection is 1/2” (12.7mm) = 21/2” (63.5mm) • SFH = Free Height Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion NFH = Neoprene Free Height • Threaded rod, nuts, and washers supplied separately • * Housings are specially reinforced for extra strength • Minimum additional travel is 50% of rated deflection at rated load Basic Hanger HHSCS-F59 thru HHSCS-F918 Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion W Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate S L S D L W Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate Typical Part Numbering HHSCS - F120 Type Load D Dimensions Part Number Vibration Isolation HHSCS-F59 HHSCS-F83 HHSCS-F120 HHSCS-F155 HHSCS-F195 HHSCS-F241 HHSCS-F348 HHSCS-F453 HHSCS-F590 HHSCS-F676 HHSCS-F787 HHSCS-F918 HHSCS-F1159 * HHSCS-F1408 * HHSCS-F1710 * HHSCS-F2318 * HHSCS-F2816 * HHSCS-F3420 * Maximum Load SFH NFH lbs. (kN) in. (mm) in. (mm) 59 83 120 155 195 241 348 453 590 676 787 918 1159 1408 1710 2318 2816 3420 (0.26) 41/4 41/4 41/4 41/4 41/2 41/2 5 5 5 5 5 5 63/8 63/8 63/8 63/8 63/8 63/8 (107.9) 11/2 11/2 11/2 13/4 13/4 13/4 13/4 13/4 21/2 21/2 21/2 21/2 23/4 23/4 23/4 23/4 23/4 23/4 (38.1) (0.37) (0.53) (0.69) (0.87) (1.07) (1.55) (2.01) (2.62) (3.00) (3.50) (4.08) (5.15) (6.26) (7.60) (10.31) (12.52) (15.21) (107.9) (107.9) (107.9) (114.3) (114.3) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (161.9) (161.9) (161.9) (161.9) (161.9) (161.9) (38.1) (38.1) (44.4) (44.4) (44.4) (44.4) (44.4) (63.5) (63.5) (63.5) (63.5) (69.8) (69.8) (69.8) (69.8) (69.8) (69.8) S in. (mm) 9 (228.6) 9 (228.6) 9 (228.6) 9 (228.6) 9 (228.6) 10 (254.0) 10 (254.0) 10 (254.0) 11 (279.4) 11 (279.4) 11 (279.4) 11 (279.4) 11 (279.4) 11 (279.4) 11 (279.4) 111/4 (285.7) 111/4 (285.7) 111/4 (285.7) W in. (mm) 3 3 3 3 3 51/2 51/2 51/2 51/4 51/4 51/4 51/4 6 6 6 11 11 11 (76.2) (76.2) (76.2) (76.2) (76.2) (139.7) (139.7) (139.7) (133.3) (133.3) (133.3) (133.3) (152.9) (152.9) (152.9) (279.4) (279.4) (279.4) L SCS Diameter D Diameter in. (mm) in. (mm) 21/2 21/2 21/2 21/2 21/2 41/2 41/2 41/2 41/2 41/2 41/2 41/2 5 5 5 5 5 5 (63.5) 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 3 3 3 3 3 3 3 3 3 3 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 5/8”-11 (60.3) (76.2) 5/8”-11 3/4”-10 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 7/8”-9 (63.5) (63.5) (63.5) (63.5) (114.3) (114.3) (114.3) (114.3) (114.3) (114.3) (114.3) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 275 B-Line series Pipe Hangers & Supports Vibration Isolation HH30SCS Type - 15° Tilt, 11/2” (38.1mm) Deflection Combination Hanger - Spring & Neoprene with Seismic Cushion Stop Use: Used to dampen noise and minor vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems.Used where uncertain alignment is anticipated during installation. At rated load the hanger rod will operate to a full 15° tilt in any direction from vertical centerline. • All housing sizes have been tested to carry five times the maximum load without failure * Extra Strength Hanger HH30SCS-E1612 thru HH30SCS-E4920 SCS (T) • Spring rated deflection is 1” (25.4mm) + neoprene rated deflection is 1/2” (12.7mm) = 11/2” (38.1mm) • SFH = Free Height NFH = Neoprene Free Height • Threaded rod, nuts, and washers supplied separately • * Housings are specially reinforced for extra strength • Minimum additional travel is 50% of rated deflection at rated load S Basic Hanger HH30SCS-ET20 thru HH30SCS-ET1326 SCS (T) Neoprene Neoprene S See Neoprene Sleeve Detail See Neoprene Sleeve Detail L SCS (B) Spring W SCS (B) L Channel D D W Typical Part Numbering Spring Neoprene Sleeve Hanger Rod Vertical Centerline Steel Washer HH30SCS - ET129 Hanger Rod Vertical Centerline Neoprene Sleeve Detail Neoprene Sleeve Type Load Neoprene Sleeve Detail Dimensions SCS (T) = Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion SCS (B) = Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate HH30SCS-ET20 HH30SCS-ET42 HH30SCS-ET80 HH30SCS-ET129 HH30SCS-ET194 HH30SCS-ET255 HH30SCS-ET347 HH30SCS-ET473 HH30SCS-ET667 HH30SCS-ET940 HH30SCS-ET1326 HH30SCS-E1612 * HH30SCS-E2060 * HH30SCS-E2460 * HH30SCS-E2980 * HH30SCS-E4120 * HH30SCS-E4920 * Maximum Load lbs. (kN) 20 42 80 129 194 255 347 473 667 940 1326 1612 2060 2460 2980 4120 4920 (0.09) (0.18) (0.35) (0.57) (0.86) (1.13) (1.54) (2.10) (2.96) (4.18) (5.90) (7.17) (9.16) (10.94) (13.25) (18.32) (21.88) SFH in. (mm) 17/8 2 21/8 23/8 23/8 21/2 23/4 27/8 31/8 33/8 35/8 35/8 37/8 41/8 41/8 37/8 41/8 (47.6) (50.8) (54.0) (60.3) (60.3) (63.5) (69.8) (73.0) (79.4) (85.7) (92.1) (92.1) (98.4) (104.8) (104.8) (98.4) (104.8) NFH in. (mm) 11/2 11/2 11/2 11/2 13/4 13/4 13/4 21/2 21/2 21/2 23/4 23/4 23/4 23/4 23/4 23/4 23/4 (38.1) (38.1) (38.1) (38.1) (44.4) (44.4) (44.4) (63.5) (63.5) (63.5) (69.8) (69.8) (69.8) (69.8) (69.8) (69.8) (69.8) S W in. (mm) in. (mm) 61/2 (165.1) 35/8 (92.1) 61/2 (165.1) 35/8 (92.1) 61/2 (165.1) 35/8 (92.1) 61/2 (165.1) 35/8 (92.1) 71/2 (190.5) 4 (101.6) 71/2 (190.5) 4 (101.6) 81/2 (215.9) 55/16 (134.9) 81/2 (215.9) 55/16 (134.9) 10 (254.0) 57/8 (149.2) 10 (254.0) 57/8 (149.2) 10 (254.0) 57/8 (149.2) 111/4 (285.7) 10 (254.0) 111/4 (285.7) 10 (254.0) 111/4 (285.7) 10 (254.0) 111/4 (285.7) 10 (254.0) 12 (304.8) 91/2 (241.3) 12 (304.8) 91/2 (241.3) L in. (mm) 21/2 21/2 21/2 21/2 3 3 41/4 41/4 43/4 43/4 43/4 4 4 4 4 7 7 (63.5) (63.5) (63.5) (63.5) (76.2) (76.2) (107.9) (107.9) (120.6) (120.6) (120.6) (101.6) (101.6) (101.6) (101.6) (177.8) (177.8) SCS Diameter D Diameter in. (mm) 23/8 23/8 23/8 23/8 23/8 23/8 23/8 23/8 3 3 3 3 3 3 3 4 4 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 3/8”-16 (60.3) 1/2”-13 (60.3) 1/2”-13 (60.3) 5/8”-11 (60.3) 5/8”-11 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) 1”-8 1”-8 1”-8 1”-8 1”-8 (76.2) (76.2) (101.6) (101.6) All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 276 Eaton Vibration Isolation Part Number Vibration Isolation HH30SCS Type - 15° Tilt, 21/2” (63.5mm) Deflection Combination Hanger - Spring & Neoprene with Seismic Cushion Stop Use: Used to dampen noise and minor vibration from suspended high speed equipment. To be used with all thread rod for single and trapeze type support systems.Used where uncertain alignment is anticipated during installation. At rated load the hanger rod will operate to a full 15° tilt in any direction from vertical centerline. * Extra Strength Hanger HH30SCS-F696 thru HH30SCS-F3420 • All housing sizes have been tested to carry five times the maximum load without failure • Spring rated deflection is 2” (50.8mm) + neoprene rated deflection is 1/2” (12.7mm) = 21/2” (63.5mm) • SFH = Free Height NFH = Neoprene Free Height • Threaded rod, nuts, and washers supplied separately • * Housings are specially reinforced for extra strength • Minimum additional travel is 50% of rated deflection at rated load SCS (T) S Basic Hanger HH30SCS-FT30 thru HH30SCS-F590 SCS (T) Neoprene Neoprene S See Neoprene Sleeve Detail See Neoprene Sleeve Detail L SCS (B) Spring W D SCS (B) L Channel D W Typical Part Numbering Spring Hanger Rod Vertical Centerline Steel Washer Neoprene Sleeve HH30SCS - FT121 Hanger Rod Vertical Centerline Type Load Neoprene Sleeve Detail Neoprene Sleeve Detail Neoprene Sleeve Part Number Dimensions Maximum Load lbs. SCS (T) = Seismic Cushion Stop (SCS) Upper Long Life Rubber Cushion SCS (B) = Seismic Cushion Stop (SCS) Lower Long Life Rubber Cushion Bonded To Steel Plate Vibration Isolation HH30SCS-FT30 HH30SCS-FT41 HH30SCS-FT60 HH30SCS-FT85 HH30SCS-FT121 HH30SCS-FT171 HH30SCS-FT241 HH30SCS-F348 HH30SCS-F453 HH30SCS-F590 HH30SCS-F696 * HH30SCS-F906 * HH30SCS-F1180 * HH30SCS-F1352 * HH30SCS-F1574 * HH30SCS-F1836 * HH30SCS-F2318 * HH30SCS-F2816 * HH30SCS-F3420 * 30 41 60 85 121 171 241 348 453 590 696 906 1180 1352 1574 1836 2318 2816 3420 SFH NFH S W L (kN) in. (mm) in. (mm) in. (mm) in. (mm) in. (mm) (0.13) 31/2 (88.9) 31/2 (88.9) 11/2 (38.1) 11/2 (38.1) 33/4 (95.2) 33/4 (95.2) 11/2 (38.1) 11/2 (38.1) 4 (101.6) 41/4 (107.9) 41/2 (114.3) 11/2 (38.1) 13/4 (44.4) (0.18) (0.26) (0.38) (0.54) (0.76) (1.07) (1.55) (2.01) (2.62) (3.09) (4.03) (5.25) (6.01) (7.00) (8.16) (10.31) (12.52) (15.21) 5 5 5 5 5 5 5 5 5 61/2 61/2 61/2 (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) (127.0) 13/4 (44.4) 13/4 (44.4) 13/4 (44.4) 21/2 (63.5) 21/2 (63.5) 21/2 (63.5) 21/2 (63.5) 23/4 (69.8) 23/4 (69.8) 23/4 (69.8) (165.1) 23/4 (69.8) 23/4 (69.8) (165.1) 23/4 (69.8) (165.1) 8 (203.2) 8 (203.2) 8 (203.2) 8 (203.2) 8 (203.2) 10 (254.0) 10 (254.0) 10 (254.0) 11 (279.4) 11 (279.4) 11 (279.4) 12 (304.8) 12 (304.8) 12 (304.8) 12 (304.8) 12 (304.8) 141/4 (361.9) 141/4 (361.9) 141/4 (361.9) 5 (127.0) 5 (127.0) 5 (127.0) 5 (127.0) 5 (127.0) 51/4 (133.3) 51/4 (133.3) 51/4 (133.3) 51/4 (133.3) 51/4 (133.3) 103/8 (263.5) 103/8 (263.5) 103/8 (263.5) 103/8 (263.5) 103/8 (263.5) 103/8 (263.5) 123/8 (314.3) 123/8 (314.3) 123/8 (314.3) 4 4 4 4 4 41/2 41/2 41/2 41/2 41/2 4 4 4 4 4 4 5 5 5 SCS Diameter in. D Diameter (mm) 23/8 (63.5) 23/8 (63.5) 1/2”-13 1/2”-13 (101.6) 23/8 (63.5) 23/8 (63.5) (101.6) 23/8 (63.5) 1/2”-13 (101.6) (101.6) (101.6) (114.3) (114.3) (114.3) (114.3) (114.3) (101.6) (101.6) (101.6) (101.6) (101.6) (101.6) (127.0) (127.0) (127.0) 3 3 3 3 3 3 3 3 3 3 3 4 4 4 1/2”-13 1/2”-13 (76.2) 1/2”-13 (76.2) 1/2”-13 (76.2) 5/8”-11 (76.2) 5/8”-11 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 3/4”-10 (76.2) 7/8”-9 (76.2) 7/8”-9 (76.2) (101.6) 7/8”-9 7/8”-9 (101.6) 7/8”-9 (101.6) 7/8”-9 All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. Eaton 277 B-Line series Pipe Hangers & Supports Vibration Isolation Vibration Isolation All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified. B-Line series Pipe Hangers & Supports 278 Eaton
© Copyright 2024 Paperzz