W-200-IS Specifications

4
3
2
17.50 in
444.5 mm
Big Dipper® IS Point Source Automatic
Grease Removal Systems
D
W-200-IS Specifications
C
C
MOTOR/DIGITAL CONTROL
ENCLOSURE
24.25”
28.50
in (616 mm) CLEARANCE FROM
723.9
mm OF TANK REQUIRED FOR
BOTTOM
23.38 in
593.7 mm
STRAINER BASKET & LID REMOVAL
C
14.00 in
355.6 mm
B
B
GC-7
GREASE
COLLECTOR
8 QUART (7.6 L)
CAPACITY
INLET
10.25 in
260.4 mm
2” (50 mm) PIPE
INLET/OUTLET
B
8.80 in
223.5 mm
A
4
10.25
6.00inin
260.4
mmmm
152.4
6.00 in
152.4 mm
3
2
SIDE
VIEW
T
Unless otherwise specified
Dimensions are in inches
Tolerances
646 GREENSBORO STREET
PO BOX 2548, ASHEBORO, NC 27203
VOICE 336-629-4651 FAX 336-626-5739
3
FEATURES:
Angular
+/- 1°
Decimals
.XX +/- .03
.XXX +/- .015
THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT
WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.
POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF
THIS DRAWING. DO NOT DESTROY THIS DRAWING, IT IS THE SOLE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.
D
6.00 in
152.4 mm
25.50 in
647.7
mm in
25.50
647.7 mm
END VIEW
4
A
7/14/14W-200-IS-SD1
MCBRIDE
DRAWN
DATE
ENGINEERING
MATERIAL (UNLESS NOTED)
CHECKED
FINISH (UNLESS NOTED)
PART NO.
SIZE
REV. NO.
DWG NO.
C
THIRD ANGLE PROJECTION
SCALE
2
SHEET
RELEASE DATE
1
OF
D
• Fully automatic self cleaning
cycle. Removes collected
A
grease & oils from tank without any operator assistance.
Comes complete with Digital Control and Grease Collector.
Unless otherwise specified
Dimensions are in inches
Tolerances
646 GREENSBORO STREET
PO BOX 2548, ASHEBORO, NC 27203
VOICE 336-629-4651 FAX 336-626-5739
INLET
3
DATE
DRAWN
7/14/14
T MCBRIDE
Angular
+/- 1°
Decimals
.XX +/- .03
.XXX +/- .015
OUTLET
THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT
WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.
POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF
THIS DRAWING. DO NOT DESTROY THIS DRAWING, IT IS THE SOLE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.
• Constructed of corrosion resistant materials suitable for
installation in virtually any location. 4Attractive sanitary
Stainless Steel exterior.
C
15.5015.50
in in
393.7393.7
mm mm
OUTLET
ENGINEERING
MATERIAL (UNLESS NOTED)
CHECKED
FINISH (UNLESS NOTED)
PART NO.
SIZE
17.50 in
444.5 mm
2
• Integrated Motor/Grease Outlet/Heater/Lid enables a fast,
do-it-yourself unit operation reversal.
C
SCALE
C
• Compact footprint.
• Two (2) No-Hub Connectors provided.
28.50 in
723.9 mm
23.38 in
593.7 mm
TOP VIEW
TECHNICAL DATA
B
Materials:
Exterior: 304 Stainless Steel, Bright Finish
10.25 in
260.4 mm
6.00 in
Maximum Inlet Flow Rate:
8.80 in
Number of Skimming
223.5 mmWheels:
Skimming Rate:
Grease Retention Capacity:
Internal Solids Strainer Capacity:
115 VAC, 50/60
Hz, mm
520 Watts (4.5 Amps)*
152.4
20 GPM (1.26 l/s)
125.50 in
647.7 mm
20 Pounds (9.08 Kg) Per Hour
40+ Pounds (18.14 Kg)
646 GREENSBORO STREET
PO BOX 2548, ASHEBORO, NC 27203
VOICE 336-629-4651 FAX 336-626-5739
Decimals
.XX +/- .03
.XXX +/- .015
Angular
+/- 1°
DRAWN
A
ASME A112.14.3
DATE
7/14/14W-200-IS-SD
T
MCBRIDE
ENGINEERING
MATERIAL (UNLESS NOTED)
CHECKED
FINISH (UNLESS NOTED)
PART NO.
2 2.
*4For Additional Electrical Configurations,3 see Electrical Variations section on page
®
Conforms to ASME Standard
ASME A112.14.3 and A112.14.4
Unless otherwise specified
Dimensions are in inches
Tolerances
1.85 Gallons (7 Liters)
THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT
WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.
POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF
THIS DRAWING. DO NOT DESTROY THIS DRAWING, IT IS THE SOLE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.
01/15
15.50 in
393.7 mm
Interior: Rotationally Molded Polyethylene
Electrical:
A
B
SIZE
REV. NO.
DWG NO.
C
SCALE
THIRD ANGLE PROJECTION
RELEASE DATE
®
1
SHEET
OF
©2015 Thermaco, Inc. • All rights reserved • Patented/Patents Pending • Specifications subject to change without notice
PO Box 2548 • Asheboro, N. C. 27204-2548 • Phone (336) 629-4651 • North America: (800) 633-4204
[email protected] • www.big-dipper.com
1
Big Dipper® IS Point Source Automatic
Grease Removal Systems
4
W-200-IS Specifications
3
2
1
INSTALLATION INFORMATION
D
Requirements
Suggested Minimum Footprint Dimensions
D
Allow a minimum of 14” (356 mm) clearance
from top of tank for removal of unit lid.
READ instruction manual included with system
before doing anything.
4 in
101.6 mm
Install unit allowing for the minimum clearances shown.
6.00 in
152.4 mm
6.00 in
152.4 mm
C
INLET
17.85 in
453.4 mm
Make sure the height above the Internal Strainer
Access Cover is enough to remove the
C strainer.
Make piping connections with rubber “No Hub”
connectors (provided).
OUTLET
Keep outlet piping as straight as possible. Use
only “sweep” connections.
Install vent on outlet piping.
Fill the tank with water before energizing the
power to the motor and heater.
5.71 in
145.1 mm
B
B
GC-7 GREASE
COLLECTOR
Set Digital Controller for proper operating times.
Do Not Install “P” trap on outlet connection of
tank. (Note: the unit already has an internal
gas trap).
4.00 in
101.6 mm
Do Not Reduce pipe size on outlet piping.
Job Specification:
A
Grease and oils separator(s) shall be Thermaco Big Dipper automatic
grease/oil recovery system(s) as manufactured by Thermaco, Inc.,

Asheboro, North Carolina
as noted on plans.
646 GREENSBORO STREET
PO BOX 2548, ASHEBORO, NC 27203
VOICE 336-629-4651 FAX 336-626-5739
4
Separator
THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT
WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.
POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF
THIS DRAWING. DO NOT DESTROY THIS DRAWING, IT IS THE SOLE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.
Specifications:
3
Unless otherwise specified
Dimensions are in inches
Tolerances
Decimals
.XX +/- .03
.XXX +/- .015
Angular
+/- 1°
DRAWN
ENGINEERING
MATERIAL (UNLESS NOTED)
CHECKED
FINISH (UNLESS NOTED)
PART NO.
2
NOTE: Drawing for reference only. Equipment must be installed in compliance with
all applicable laws, regulations and codes,
A should
including plumbing codes. Installation
be performed by a qualified plumber.
SMFD-W-200-250-IS
DATE
SIZE
REV. NO.
DWG NO.
C
SCALE
THIRD ANGLE PROJECTION
RELEASE DATE
1
SHEET
OF
Furnish and install ___ Thermaco Big Dipper Model No. W-200-IS, bright finish type 304 stainless steel exterior, rotationally
molded polyethylene interior automatic self-cleaning grease and oil recovery separator(s) for floor mounted or partially recessed installation, rated at 20 gallons per minute (1.26 liters per second) peak flow, 40 pounds (18.14 Kg) of grease capacity
and including as an integral part of the unit, 1 rotating gear hydrophobic wheel assembly for automatic grease/oil removal, an
integral flow control device, self-regulating enclosed electric immersion heater, a vessel vent, an integral gas trap, a digital
control for programmable operation, a field reversible motor location, a field reversible grease/oil sump outlet, quick release
stainless steel lid clamps, a gasketted and fully removable 304 stainless steel lid, a lift-out strainer basket access, an internal
stainless steel strainer basket for collection of coarse solids, and a separate grease and oils collection container. Electric
assembly shall be tested to comply with pertinent sections of the Standards for Safety ANSI/UL 73 and/or ANSI/UL 1004.
Electric motor equipped with overload protection. Two (2) no-hub connectors for plumbing connection provided.
Electrical Variations:
W-200-IS: W-200-IS-E: W-200-IS-2360:
115V 50/60Hz, 520 Watts (4.5 Amps)
230V 50/60Hz, 520 Watts (2.3 Amps)
230V 50/60Hz, 520 Watts (2.3 Amps)
©2015 Thermaco, Inc. • All rights reserved • Patented/Patents Pending • Specifications subject to change without notice
2
PO Box 2548 • Asheboro, N. C. 27204-2548 • Phone (336) 629-4651 • North America: (800) 633-4204
[email protected] • www.big-dipper.com
01/15