®
Currency® Bookcase
B
T
Components
Description
End Panel
Back Panel
Top Panel
Middle Fixed Shelf
Lower Fixed Shelf
Adjustable Shelf
Kick Plate
A
A
Letter
E
B
T
MC
LC
A
LO
E
E
C
M
T
#2 ACR BIT
C
L
A
A
A
M
C
LO
A
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
© 2012 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
L
C
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
E
Page 1 of 6
939500297 Rev D
®
(Tips for Proper Alignment of Parts)
Make sure the cam
lock is located parallel
to the side of the
surface as shown.
CAM LOCK
(See cam lock note)
CAM LOCK NOTE:
If cam lock is installed high on the surface,
tap it down flush with the surface. If that
doesn't work, replace part.
If cam lock is installed low into the surface,
screw cam pin out to extend the length of
the cam pin.
Apply stickers on all visible cam
joint faces to cover the connector
faces, after assembly.
Use mallet, before tightening cam screws, to
bring parts together and avoid light leaks.
CAM LOCK ADJUSTMENT TOOL
TURN
CLOCKWISE
WRONG
Fasten Cam Locks
(The cam lock screw needs to
be turned 3/4 full turn or 270o
clockwise for complete
engagement.)
If the cam lock screw is not
visible, you have installed
the panel/shelf wrong and
you need to turn the
panel/shelf 180o.
NOTE: The cam pin is offset and needs to be installed
on the shorter offset side. If the screw heads are not
visible, turn the panel/shelf 180o.
Shorter
off-set side
WRONG
Shorter
off-set side
PANEL
CAM PIN
SCREW HEAD
VISIBLE
SCREW HEAD
NOT VISIBLE
CAM LOCK
NOTE: When assembly has been completed,
make sure to remove all of the E, B, T, ect.
stickers from the surfaces of all the parts.
CAM LOCK
Page 2 of 6
939500297 Rev D
®
2b
NOTE: Assemble as close to assembled units final desired location
to avoid moving a heavy unit.
2a
1. Lower the B (back panel) onto E (end panel) as shown. Make sure pins
engage into cams (see page 2 for alignment of parts).
B
E
2. Lower LC (lower fixed shelf) (2a) and MC (middle fixed shelf)
(2b) onto the end panel and against the back panel. (Rock back
panel slightly for installation) Make sure pins engage
into cams. Tighten cams located on end panel.
LC
MC
1
3. Lower LO (kick plate) onto the end
panel and against the lower fixed shelf.
Make sure pins engage into cams.
B
TURN
CLOCKWISE
Fasten Cam Locks in 4 places
TURN
CLOCKWISE
3
(The cam lock screw needs to be turned
3/4 full turn or 270o clockwise for
complete engagement.)
Fasten Cam Locks in 4 places
(The cam lock screw needs to be turned
o
3/4 full turn or 270 clockwise for
complete engagement.)
LC
E
LO
Page 3 of 6
939500297 Rev D
®
4. Lower the second E (end panel) onto the back panel, middle fixed shelf
and lower fixed shelf as shown. Start at the top of the unit and work
towards the bottom, aligning each pin and dowel. This may
require a rubber mallet to fully seat all of the pins.
#8-18 X 5/8"
PH TAPPING
SCREW
4
BLACK
PLASTIC
BRACKET
LC
E
5. Align five (5) black plastic brackets with
the lower fixed shelf and the end panel or
the kick plate as shown. Attach each
bracket with four (4) #8-18 x 5/8"
ph tapping screws.
5
B
E
MC
TURN
CLOCKWISE
LC
Fasten Cam Locks in 4 places
TURN
CLOCKWISE
TURN
CLOCKWISE
(The cam lock screw needs to be turned
o
3/4 full turn or 270 clockwise for
complete engagement.)
Fasten Cam Locks in 4 places
(The cam lock screw needs to be turned
o
3/4 full turn or 270 clockwise for
complete engagement.)
Fasten Cam Locks in 4 places
(The cam lock screw needs to be turned
3/4 full turn or 270o clockwise for
complete engagement.)
Page 4 of 6
939500297 Rev D
®
Fasten Cam Locks in 7 places
7
6. Raise the unit into an upright position as shown.
T
7. Lower the T (top panel) onto the back panel and
both end panels as shown. Make sure pins engage
into cams and tighten all cams.
(The cam lock screw needs to be turned
3/4 full turn or 270o clockwise for
complete engagement.)
TURN
CLOCKWISE
8. Adjust glides in four (4) places to level unit.
E
E
6
C
M
E
8
B
B
C
L
LC
MC
E
Level unit by adjusting
glides in 4 places on
bottom of unit.
Page 5 of 6
939500297 Rev D
®
NOTCH
SHELF SUPPORT PIN
9. Insert twelve (12) shelf pins into
holes located on the end panels.
10
9
10. Align A (adjustable shelves)
T
withshelf pins and lower
onto pins.
A
L
C
L
C
A
M
C
M
C
A
T
UNDERSIDE
OF SHELF
E
E
Apply stickers on all visible cam joint faces to
cover the connector faces, after assembly.
Page 6 of 6
939500297 Rev D