VB-06
Harlequin®/Harlequin Essence®
VM4987 Cyan to Purple
VM4988 Silver to Green
VM4989 Green to Purple
VM4990 Blue to Red
VM4991 Magenta to Gold
VM4994 Gold Silver
Harlequin ® is a series of exotic, color-shifting
special finishes showcasing some of the wildest
color effects imaginable.
Harlequin Essence ® combines Harlequin
pigments with Global and Deltron ® 2000
basecoat toners to create a more subtle yet
unique color transition.
Compatible Surfaces
Harlequin/Harlequin Essence is used in conjunction with the systems shown below:
• DBC Refinish Systems—Follow P-175 Deltron® DBC recommendations for proper preparation and compatible
primers. • Global BC Refinish Systems—Follow EU02 Global BC recommendations for proper preparation and compatible
primers. • Reference the Vibrance Compatibility Chart (VB20) for compatible Clears and custom formulating. Note: Custom or exotic finishes are excluded from coverage under the PPG Paint Performance Guarantee.
Product Information Effective 4/07
Harlequin /Harlequin Essence
®
®
Directions For Use
Preparation: When working on custom finishes close attention to the details outlined for
standard basecoat preparation, sanding, and cleaning is needed to achieve the
optimum results.
Harlequin®/Harlequin Essence® are designed to be applied over properly cleaned,
sanded and primed surfaces. See the Compatible Surfaces section of Product
Information Bulletin P-175 (DBC) or EU02 (Global Basecoat) for an appropriate
primer or sealer recommendation.
Settling may occur in shipping. Hand stir thoroughly before the addition of the solvent.
Mixing Ratio:
DBC Reduction
Standard Mix as a Basecoat
DBC
:
DT Reducer
or
BC
1 part
:
1 part
1 part :
Tri-Coat Mixing
BC Reduction
:
D-Thinners
1 part
When mixing for a tri-coat applications, 5% DX57 Basecoat Activator (DBC) or
D888 Basecoat Activator (BC) should be added to the reduced basecoat prior to
spraying in both the ground coat and mid coat.
Harlequin can be blended as a mid-coat color with DBC500 Color Blender or
D895 Color Blender (BC). In doing so you can achieve more transparency, when
combined with varying ground coat colors and create different degrees of custom
effects. DBC500 and D895 can be used in any quantity necessary to achieve the
desired effect.
Pot Life:1 hour at 70°F (21°C) when mixed with DX57 or D888 Activators.
Using material beyond 1 hour may result in wrinkling or other product failures.
Additives:
Fisheye Eliminators are not recommended in basecoats.
A
B
Flex Additives are not needed for basecoats. Ready-to-spray color may be applied to properly prepared flexible parts.
Spraygun Set-up:
Groundcoat: 2–3 medium coats until hiding is achieved.
Apply:
Midcoat: If using Harlequin as a tri-coat, spray as many coats as needed to achieve your desired color.
Fluid Tip:
1.1–1.3 mm or equivalent
Air Pressure:
10 PSI at the cap for HVLP guns
35–45 PSI at the gun for conventional guns
Directions For Use
Drying Times: Between Coats:
70°F (21°C)
5–10 minutes
Tape Time:
70°F (21°C)
20–40 minutes (30–60 minutes with DX57 or D888)
Dry Time to Clearcoat:
15–30 minutes at 70°F (21°C)
After 24 hours basecoat must be sanded and
additional color applied. Clearcoating:
Harlequin/Harlequin Essence colors may be clearcoated with any compatible
Deltron® or Global clear. See the Compatible Clearcoats section of P-175 and
EU02 for a complete listing.
Custom or exotic finishes are excluded from coverage under the PPG Paint
Performance Guarantee.
Technical Data:
STD Reduction
With DX57 or D888
Package VOC Actual
5.2–6.16 lbs/gal
(623–738 g/l)
5.2–6.16 lbs/gal
(623–738 g/l)
Package VOC Regulatory (Less Water Less Exempts)
5.2–6.16 lbs/gal
(623–738 g/l)
5.2–6.16 lbs/gal
(623–738 g/l)
1:1 RTS VOC Regulatory
(Less Water Less Exempts)
5.9–6.6 lbs/gal
(707–791 g/l)
5.7–6.36 lbs/gal
(683–762 g/l)
Harlequin /Harlequin Essence
®
®
Directions For Use
Important:
The contents of this package must be blended with other components before the
product can be used. Before opening the packages, be sure you understand the
warning messages on the labels of all components, since the mixture will have
the hazards of all its parts. Improper spray technique may result in a hazardous
condition. Follow spray equipment manufacturer’s instructions to prevent personal
injury or fire. Follow directions for respirator use. Wear eye and skin protection.
Observe all applicable precautions.
See Material Safety Data Sheet and Labels for additional safety information and handling instructions.
EMERGENCY MEDICAL OR SPILL CONTROL INFORMATION (412) 434-4515; IN CANADA (514) 645-1320
Materials described are designed for application by professional, trained personnel using proper equipment and are not intended
for sale to the public. Products mentioned may be hazardous and should only be used according to directions, while observing
precautions and warning statements listed on label. Statements and methods described are based upon the best information and
practices known to PPG Industries. Procedures for applications mentioned are suggestions only and are not to be construed as
representations or warranties as to performance, results, or fitness for any intended use, nor does PPG Industries warrant freedom
from patent infringement in the use of any formula or process set forth herein.
PPG Industries
19699 Progress Drive
Strongsville, OH 44149
(800) 647-6050
PPG Canada Inc.
2301 Royal Windsor Drive
Mississauga, Ontario L5J 1K5
(888) 310-4762
© 2007 PPG Industries www.ppgrefinish.com Part No. VB-06, 4/07