1738
Quick Setup for Pre-Programmed Systems
Step 1:
Connecting Hardware
If you are using EOL
resistors, refer to
“Hardwire Zone
Connection Using EOL
Resistors” on page 4.
Step 2:
How to Program
2.1
2.2
Step 3:
Section
[143]
[151]
[153]
[ENTER] J[INSTALLER CODE] (default: 0000) J[SECTION] J[DATA] J[ENTER] to save.
Press [CLEAR] at any point to exit and then enter a new section.
Minimum Programming for Monitoring Station Reporting
Description
Data
Partition 1 Account Number (press the [FORCE] key if less than 4
digits; to enter hexadecimal values refer to the “Decimal and
Hexadecimal Programming Table” on page 4)
____/____/____/____
Monitoring Station Telephone Number 1 (press the [ENTER] key if
less than 32 digits)
__________________________________
Backup Monitoring Station Telephone Number (press the
[ENTER] key if less than 32 digits)
__________________________________
Maximum: 32 digits
Maximum: 32 digits
1
Step 4:
Optional Programming with Defaults and Pre-Programmed Settings
If a hardware reset is performed, the control panel will reset to factory defaults (refer to the Spectra
Programming Guide) and the pre-programmed settings will be lost.
† = pre-programmed setting
Section
Description
Data
Zone Definitions
Empty slot [FORCE] - Disabled
1 - Entry Delay 1
Additional definitions for on2 - Entry Delay 2
board terminals:
3 - Follow
7 - Keyswitch
4 - Instant
8 - Standard 24Hr Fire
5 - 24Hr Buzzer
9 - Delayed 24Hr Fire
6 - 24Hr Burglary
Partition Assignment
Empty - Zone disabled
1 - Partition 1
2 - Partition 2
3 - Both partitions
[4]
[5]
OFF
OFF
Steady Alarm
OFF
ON
Pulsed Alarm
ON
OFF
Silent Alarm
ON
ON
Report Only
Zone Options
[6] - Intellizone
[7] - Delay before transmission
[8] - Force Zone
Zone Alarm Type
Keyswitch Options
[1] - OFF = Maintained / ON = Momentary
[2] - OFF = Regular arm / ON = Stay arm
Zone 1 : Entry Delay 1 zone
1 /____
1
____
( 1 2 * * * * * *)
Zone 2 : Follow zone (Stay Zone enabled)
3 /____
1
____
( 1 2 3 * * * * *)
Zone 3 : Instant zone
4 /____
1
____
( 1 2 * * * * * *)
Zone 4 : Instant zone
4 /____
1
____
( 1 2 * * * * * *)
Zone 5 : Instant zone
4 /____
1
____
( 1 2 * * * * * *)
Zone 6 : Instant zone
4 /____
1
____
( 1 2 * * * * * *)
Zone 7 : Instant zone
4 /____
1
____
( 1 2 * * * * * *)
PGM1 Timer
0
3
0 seconds
____/____/____
[069]
Entry Delay 1
0
4
5 seconds
____/____/____
[070]
Entry Delay 2
0
4
5 seconds
____/____/____
[071]
Exit Delay 1
0
3
0 seconds
____/____/____
[072]
Exit Delay 2
0
3
0 seconds
____/____/____
[073]
Bell Cut-off Timer Partition 1
0
0
4 minutes
____/____/____
[077]
†
[001]
†
[002]
†
[003]
†
[004]
†
[005]
†
[006]
†
[007]
†
[066]
†
Answering Machine Override Delay (000 to disable)
0
3
2 seconds
____/____/____
Event Group #
Sub-group #
Partition #
0
1
_____/_____
0
1
_____/_____
[120]
†
PGM1 Activation Event ([PG]/[FNC1] was pressed; smoke reset)
0
5
_____/_____
[126]
†
PGM1 Normal State
Option [4]
‡ OFF = N.O.
‡ ON = N.C.
Option [8]
‡ OFF = Disabled
3
‡ ON = Enabled
Option [4]
‡ OFF = Disabled
‡ ON = Enabled
Option [6]
‡ OFF = Disabled
3
‡ ON = Enabled
Option [1]
‡ OFF = Disabled
‡ ON = Enabled
Zone 1 becomes 2-wire smoke detector input
[127]
†
Lock System Master Code
User Code 048 is a Duress Code
[128]
2
[1] - Auto-zone Shutdown Enabled
[2] - Bypass Enabled
[3] - Stay Zone
†
Panic 1 (keys [1] and [3])
3
3
3
† = pre-programmed setting
†
Panic 2 (keys [4] and [6])
Option [2]
‡ OFF = Disabled
†
Panic 3 (keys [7] and [9])
Option [3]
‡ OFF = Disabled
†
Panic 1 alarm type
Option [4]
‡ OFF = Silent Alarm
†
Panic 2 alarm type
Option [5]
‡ OFF = Silent Alarm
†
Panic 3 alarm type
Option [6]
‡ OFF = Silent Alarm
3
‡
3ON = Enabled
‡
3ON = Audible Alarm
‡
3ON = Audible Alarm
‡
3ON = Fire Alarm
[129]
†
Wireless Module Low Battery Supervision
Option [6]
‡ OFF = Disabled
‡ ON = Enabled
[130]
†
One-touch Regular Arming
Option [1]
‡ OFF = Disabled
‡ ON = Enabled
†
One-touch Stay Arming
Option [2]
‡ OFF = Disabled
†
One-touch Force Arming
Option [3]
‡ OFF = Disabled
†
One-touch Bypass Programming
Option [4]
‡ OFF = Disabled
3
‡
3ON = Enabled
‡
3ON = Enabled
‡
3ON = Enabled
[131]
†
No exit delay beeps and no bell squawk when Stay arming
Option [5]
‡ OFF = Disabled
‡ ON = Enabled
[132]
EOL (End-of-line) resistors
Option [4]
‡ OFF = No EOL
3
‡ ON = with EOL
[133]
Switch to Stay Arming if no entry delay is opened
Option [4]
‡ OFF = Disabled
3
‡ ON = Enabled
[135]
†
Dialer
Option [3]
‡ OFF = Disabled
‡ ON = Enabled
[137]
†
Call Telephone #1 for Arming/Disarming Report Codes
Option [1]
‡ OFF = Disabled
3
‡ ON = Enabled
[140]
Reporting formats for telephone numbers 1 and 2. Enter a
number from 1 to 6.
(1 = ADEMCO slow; 2 = Silent Knight fast; 3 = SESCOA;
4 = ADEMCO Express; 5 = ADEMCO Contact ID; 6 = Pager)
[302]
†
Master Code 1
( 1 * 3 4 5 * * *)
[303]
†
Master Code 2
( 1 * 3 4 5 * * *)
[304]
†
User Code 004
( 1 * 3 4 5 * * *)
[348]
†
User Code 048
( 1 * 3 4 5 * * *)
‡ ON = Enabled
3
3
3
5 /_____
5
_____
Tel.# 1
Format
Tel.# 2
Format
User Options
[5] Force Arming
[1] Partition 1 access
[6] Arm only
[2] Partition 2 access
[7] PGM activation only
[3] Bypass programming
[8] Future use
[4] Stay arming
Buttons
Section
+
*
+
+
*
+
*
4
5
_____
_____ _____
Remote control # 1 _____
_____
_____
_____
_____
4
5
_____
_____ _____
Remote control # 2 _____
_____
_____
_____
_____
4
5
_____
_____ _____
Remote control # 3 _____
_____
_____
_____
_____
4
5
_____
_____ _____
Remote control # 4 _____
_____
_____
_____
_____
4
5
_____
_____ _____
Remote control # 5 _____
_____
_____
_____
_____
4
5
_____
_____ _____
Remote control # 6 _____
_____
_____
_____
_____
4
5
_____
_____ _____
Remote control # 7 _____
_____
_____
_____
_____
4
5
Remote control # 8 _____ _____ _____ _____
_____
_____
_____
_____
[711]
†
[712]
†
[713]
†
[714]
†
[715]
†
[716]
†
[717]
†
[718]
†
Button Options
Empty slot [FORCE] = Button disabled
1 - Regular arming
2 - Stay arming
3 - Instant arming
4 - Force arming
5 - Disarm
6 - Disarm when no alarm
7 - Regular arm and disarm
8 - Panic 1
9 - Panic 2
A - Panic 3
B - PGM activation (Event group # 07)
C - PGM activation (Event group # 08)
D - PGM activation (Event group # 09)
* = The greyed-out columns indicate button combinations not available with the MG-REM1 remote control and cannot be programmed.
3
Step 5:
Testing
• Arm the system with [MASTER CODE] (default: 1234)
• Trigger zones to verify operation
Decimal and Hexadecimal Programming Table
What Do I See?
Value or Action
What Do I
Press?
1686V
1686H
1689
1641
1640
10-Zone LED
16-Zone LED
LCD
Icon LCD
Values 1 to 9
[1] to [9]
[1] to [9]
[1] to [9]
[1] to [9]
[1] to [9]
A (HEXA ONLY)
[0]
[0 (10)]
[10]
0
0
B (HEXA ONLY)
[STAY] /
[STAY]
[11]
B
B
C (HEXA ONLY)
[BYP] /
[BYP]
[12]
C
C
D (HEXA ONLY)
[MEM] /
[MEM]
[13]
D
D
E (HEXA ONLY)
[TBL] / [TRBL] /
[TBL]
[14]
E
E
F (HEXA ONLY)
[PG] / [FNC1] /
[PG]
[15]
F
F
[CLEAR] /
[ENTER] flashes
[ARM1] & [STAY1] flash
“PROGRAMMING MODE
[
]
SECTION”
“SECTION”
In Programming Mode
/ Waiting for a Section
__
[ENTER] flashes
[ARM1] & [STAY1] flash
“PROGRAMMING MODE
[
]
SECTION”
“SECTION”
Enter a Space / Erase
Current Digit
[FORCE] /
Exit Without Saving
Save Data (HEXA
ONLY)
[ENTER] /
Displays next digit or next section
Advances to the next section
Installer Quick Keys
To access the installer quick keys, press the [ENTER] key, enter your [INSTALLER CODE] and then press:
• [TBL] or [TRBL] (Installer Test Mode): The Installer Test Mode will allow you to perform walk tests.
•
[MEM] (Test Report): Sends the “Test Report” report code programmed in section [211] to the monitoring station.
•
[BYP] (Call WinLoad): Dials the PC telephone number (section [150]) to initiate communication with WinLoad.
•
[STAY] (Cancel Communication): Cancels all communication with WinLoad or monitoring station until next reportable event.
•
[FORCE] (Answer WinLoad): Will force the control panel to answer an incoming call from WinLoad.
Hardwire Zone Connection Using EOL Resistors
Printed in Canada - 10/2004
4
1738-EQ02