Release Notes
DriveTools SP Version 5.06 Software Patch
This release note describes major version 5, minor version 6 of DriveTools SP
software. This patch is not a complete installation and only installs the necessary
updated software components.
The following information is included in this document:
Topic
Page
Determining Your Software Version
2
Installing the Software Patch
3
Verifying the Software Component Versions
4
Enhancements
5
Corrected Anomalies
6
Restrictions
6
2
Determining Your Software
Version
This section describes the procedures to determine the software version of your
DriveTools SP software package. You must have versions 3.01…5.05 already
installed on your PC in order to update to version 5.06.
Method #1
Launch DriveExecutive and read the version number that is displayed in the
startup window. Note the startup window is only momentarily displayed when
DriveExecutive launches. If you could not read the version in time, use Method
#2 below to view the version.
Method #2
In DriveExecutive, select Help >> About DriveExecutive to display the About
DriveExecutive Software window.
Rockwell Automation Publication 9303-RN021A-EN-P - July 2012
3
The version number will be located under the DriveExecutive name on the
General tab (see image below).
Installing the Software
Patch
This section describes the procedure for installing the software patch. You must
have versions 3.01…5.05 already installed on your PC in order to update to
version 5.06.
1. Install the necessary version 5.06 patch over versions 3.01…5.05 on your
PC.
2. Open DriveExecutive.
3. Continue with Verifying the Software Component Versions on page 4.
Rockwell Automation Publication 9303-RN021A-EN-P - July 2012
4
Verifying the Software
Component Versions
Method #1
Launch DriveExecutive and read the version number that is displayed in the
startup window. Note the startup window is only momentarily displayed when
DriveExecutive launches. If you could not read the version in time, use Method
#2 to view the version.
Rockwell Automation Publication 9303-RN021A-EN-P - July 2012
5
Method #2
In DriveExecutive, select Help >> About DriveExecutive to display the About
DriveExecutive Software window. The version number will be located under the
DriveExecutive name
Enhancements
This section describes the enhancements provided in this version of software:
Support for DeviceLogix Editor Version 5.003
The version 5.06 software patch updates the DriveExecutive™ software to include
the latest DeviceLogix editor. This update corrects some issues that could cause
DriveExecutive to crash or stop running.
Support for the 20-750-ENETR Dual-port EtherNet/IP Option
Module
Added support for the new 20-750-ENETR in Standard and Tap modes.
Rockwell Automation Publication 9303-RN021A-EN-P - July 2012
6
Corrected Anomalies
This section describes the anomalies corrected in this revision for software:
PowerFlex 755 Drive Diagrams Display for PowerFlex 753 and
PowerFlex 755 Frame 8 and Larger Drives
Anomaly: The diagrams for PowerFlex 755 drives display for both the PowerFlex
753 and PowerFlex 755 Frame 8 and larger drives.
Correction: The correct diagrams now display for both the PowerFlex 753 and
PowerFlex 755 Frame 8 and larger drives.
Control Bar Does Not Work for PowerFlex 750-Series Drives
Through the 1203-USB
Anomaly: The control bar does not work for PowerFlex 750-Series drives when
using a 1203-USB converter.
Correction: The control bar issue has been resolved for PowerFlex 750-Series
drives when using a 1203-USB converter, as well as the 20-WIM-Nx wireless
interface module.
Restrictions
The following restriction applies to this revision of firmware:
DriveTools SP Versions 3.01…5.05
DriveTools SP software versions 3.01…5.05 must already be installed on
your PC in order for the version 5.06 software patch to install. If versions
3.01…5.05 are not already installed on the PC an error message will occur, stating
that versions 3.01…5.05 were not found.
Rockwell Automation Publication 9303-RN021A-EN-P - July 2012
7
Rockwell Automation
Support
Rockwell Automation provides technical information on the web to assist you in
using our products. At http://support.rockwellautomation.com, you can find
technical manuals, a knowledge base of Frequently Asked Questions (FAQs),
technical and application notes, sample code and links to software service packs,
and a MySupport feature that you can customize to make the best use of these
tools.
Rockwell Automation also provides complimentary phone support for drives,
communication adapters, and peripherals. If you experience a problem with the
software, please review the information in the online Help. For further help in
getting your software operational, contact a Customer Support representative:
United States
1.262.512.8176
Monday – Friday, 7am – 6pm CST
Outside United States Please contact your local Rockwell Automation representative for any
technical support issues.
For an additional level of technical phone support for installation, configuration
and troubleshooting, we offer TechConnect Support programs. For more
information, contact your local distributor or Rockwell Automation
representative, or visit http://support.rockwellautomation.com
Rockwell Automation Publication 9303-RN021A-EN-P - July 2012
Allen-Bradley, Rockwell Software, Rockwell Automation, and TechConnect are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
Publication 9303-RN021A-EN-P - July 2012
Copyright © 2012 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.