Wiring diagram LINEARdrive 100/A
(LIN100A1)
In Europe, use a H03V 0.75mm2 power
Pay attention when connecting the LED groups:
cable and apply following strip lengths:
polarity reversal results in no light output and often
damages the LEDs
15 mm
120-277
VAC
DALI
{
{
6 mm
4 LED groups, 4 control channels
LedSync out +
LedSync out LedSync out shield
N
L
DMX in shield
DMX in DMX in +
R
G
B
W
R
R
R
R
Common anode
+
+
-
M
12V / 24V DIP switch
24V
Ext in Ext in +
AWG 20-16
0.5-1.5 mm 2
1
2
1
12V
Non functional
AWG 24-16
0.2-1.5 mm 2
2
9 mm
0.35 inch
9 mm
0.35 inch
WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
120-277VAC
LED wire length
The driver accepts a universal mains voltage input of 120-277VAC,
Maximum wire length from LED driver to LED engine at full load:
50/60Hz.
DALI
Use these connectors to connect the driver to a DALI network. Always
combine a DA+ and DA- connector for either data input or data output.
DMX in/LedSync out
Use these connectors when the driver is used in a DMX network. For
DMX in, connect the network cable’s DMX+, DMX- and DMX shielding
wire (the orange/white, orange and brown wire in a CAT5 cable) to the
AWG value
20
19
18
17
16
Distance (m)
14
18
22
28
36
Distance (ft)
46
59
72
92
118
Please observe voltage drop over long wire lengths.
Longer wire lengths increase EMI susceptibility.
DMX in+, DMX in- and DMX in shield connector respectively. For
LedSync out, connect the network cable’s DMX+, DMX- and DMX
shielding wire to the LedSync out+, LedSync out- and LedSync out
shield connector respectively.
Ext in
You have the possibility to connect an external control device (passive
0-10V control device, 10kΩ potentiometer or show selection switch) to
the driver’s Ext in+ and Ext in- connectors. Configure the driver for use
with an external control device over the 3-button user interface.
LED groups
Indicates the location of the connectors for your LED groups. R(ed)
represents channel 1, G(reen) represents channel 2, B(lue) represents channel 3 and W(hite) represents channel 4. One common
anode provides the positive supply voltage for all four LED groups.
The default group color allocation can be changed over the 3-button
user interface.
12-24V DIP switch
Set DIP switch 1 to ON when you’re connecting a 24V LED strip; set
DIP switch 1 to OFF when you’re connecting a 12V LED strip. (DIP
switch 2 is not used.)
Warning: setting DIP switch 1 to ON for use with 24V LEDs and subsequently connecting 12V LEDs can damage the LEDs!
© 2013 eldoLED. All rights reserved. V1.7
More product documentation and eldoLED’s terms and conditions are available at www.eldoled.com.
Wiring diagram LINEARdrive 100/A
(LIN100A1)
Connecting an RGB LED strip
Maximum current per output at 12V: 2.77A
Maximum current per output at 24V: 1.33A
RGB LED strip
+
R
G
B
Configuration of the LED groups:
Press M and + simultaneously, in the LED menu choose RGB and
save by pressing M.
Compact
connector
e.g. Wago 222
Connecting an RGB strip and a white LED strip
Maximum current per output at 12V: 2A
Maximum current per output at 24V: 1A
RGB LED strip
+
R
G
B
Configuration of the LED groups:
Press M and + simultaneously, in the LED menu choose RGBW and
White LED strip
save by pressing M.
+
-
Compact
connector
e.g. Wago 222
Connecting warm white and cool white LED strips
Warm white LED strip
Maximum current per output at 12V: 2A
+
Maximum current per output at 24V: 1A
-
Cool white LED strip
+
Configuration of the LED groups:
-
Press M and + simultaneously, in the LED menu choose 4-4L and
Warm white LED strip
+
save by pressing M.
-
Cool white LED strip
+
-
Compact
connector
e.g. Wago 222
Connecting four white or self-colored LED strips
Maximum current per output at 12V: 2A
White LED strip
+
Maximum current per output at 24V: 1A
-
White LED strip
Configuration of the LED groups:
+
Press M and + simultaneously, in the LED menu choose 1-4L and
-
save by pressing M.
White LED strip
+
-
White LED strip
+
-
eldoLED Europe B.V.
eldoLED America, Inc.
Luchthavenweg 18a
1762 Technology Drive # 226
5657 EB Eindhoven
San Jose, CA95110
The Netherlands T +31 40 2054050
USA
T +1 408 451 9333
F +31 40 2054058
F +1 408 451 9335
[email protected]
[email protected]