Swimming Pool
Epoxy Topcoat
DESCRIPTION
STANDARD COLOURS
A two-part epoxy resin-curing agent swimming
pool paint
Screen or printer colour representations may vary from actual paint
colours. Final appearance will be influenced by water conditions
and light reflections. Darker colours may be prone to more visible
bleaching over time.
PRODUCT DATA
INTENDED USE
A high-solids performance coating for swimming
pools, ponds or tanks. Performs excellent in
submerged conditions offering a tough, abrasive
resistant, gloss finish for cementitious or
fibreglass type surfaces. For highest bonding
strength, use in conjunction with Pool Solutions
Primer epoxy.
PRODUCT FEATURES
Components
2
Mix Volume Ratio
3:1
Density: A-part
1.4 - 1.5Kg / litre
Density: B-part
1.0Kg / litre
Volume Solids %
94
Temp. resistance
70ºC
APPLICATION DATA
Pot Life
45min @ 25ºC
Touch-dry (coating)
4 hours @ 25ºC
•
Excellent colour and colour retention
Walk-over dry time
16 hours @ 25ºC
•
Very good chemical resistance
Filling with water (summer)
•
100% algae resistant
Filling with water (winter)
3 days @ 25ºC or
above
7 days @ 18ºC or
less
•
Excellent resistance to waterspotting at
ambient and low temperatures, high humidity
conditions during application
Pot Life
45min @ 25ºC
Spread rate
(roller - 3 layers application)
10-12m² / layer
•
High gloss
6.5m² / layer
•
Very good abrasion resistance
Spread rate
(spray - 2 layer application)
Final coating thickness
•
420-500 micron dry
Fast cure above 18ºC, cures at 10ºC
Temp. resistance
70ºC
•
No induction time after mixing
LIMITATIONS
•
•
Calcium Hardness of water below 300ppm
will increase chalking and reduce lifespan,
water must be tested after filling or topping
up
Eventual thinning of the coating due to UV
exposure. Apply 3 layers on swimming
pools to prolong lifespan
PACKAGING
Plastic paint bucket with handles
packaged in sets as per 3:1 mix volume ratio:
A – PART (Resin)
B – PART (Curing)
5L bucket (filled 3L)
1L bucket (filled 1L)
10L bucket (filled 6L)
2L bucket (filled 2L)
10L bucket (filled 9L)
5L bucket (filled 3L)
20L bucket (filled 15L)
5L bucket (filled 5L)
Pool Solutions Epoxy Coatings | 083 455 9632 |Email: [email protected] |Web: www.poolsolutions.co.za
Swimming Pool
Epoxy Topcoat
SURFACE PREPARATION
Abrade the surface thoroughly with a 230mm
grinder fitted with rubber backing disc, using
P16 to P36 fibre grinding discs to achieve a
clean profile, or use approved methods of
abrasive blasting. Fill cracks and holes with
Underwater Pool Patching (Cemcrete) or an
underwater epoxy filler.
HEALTH AND SAFETY
•
Flammable – keep away from sources of
ignition – No smoking!!!
•
Adequate ventilation should be provided
during use
•
Avoid contact with the skin by using
gloves, barrier creams and face mask
Mixing Two Components – Ratio 3:1
•
Stir Part-A well separately with an electric drill
and mixing tip for 2 minutes. Use 3 x Part-A and
1 x Part-B. Mix well for 2-3 minutes until mix is
homogeneous Stir Part-A separately and
regularly during the project before mixing the
two components together.
If the product comes into contact with the
skin, wash immediately with lukewarm
water and soap, if the eyes are affected
flush with water or dilute boric acid
solution and seek medical attention
immediately
•
Refer to Material Safety Data Sheet
(MSDS)
PRODUCT APPLICATION
NB: Refer to the complete installation
instructions available from our website
STORAGE AND HANDLING
CONDITIONS
Ambient
Temperature
Relative
Humidity
Min:
10ºC
No lower limit
Max:
40ºC
85%
Storage - Store at temperatures between 5°C
and 40°C, away from direct sunlight, open flames
or sparks
Flash Point - 18°C
The surface must be completely dry. Moist
testers can be used to ensure the structure’s
moist level is below 10% or use a clear plastic
sheet taped around the edges to the surface of
the swimming pool for 24 hours. If moist
accumulates underneath or dampness appears
in the surface, do not apply the epoxy paint
Equipment and Methods
Brushes and rollers
Use short pile rollers suitable
for enamel paints
Airless spray
Pump Ratio - 30 to 1 min
Nozzle - 13 to 15 Thou
Tip Pressure - 145 Bar Min
Equipment
DO NOT ADD THINNERS OR SOLVENTS TO THE
EPOXY PAINT
Cleaning - Use normal paint thinners or epoxy
thinners to clean equipment within 30 minutes after
filling
Shelf Life - Minimum 1 year when packed in
original containers
DISCLAIMER
Pool Solutions, the owners, dealers or affiliates, will not be
held responsible in any way for any accidents, injuries,
health-related problems or any other damage claims arising
from the storage, use, or application of the product.
Whilst we endeavour to ensure that all advice we give about
the product is correct, the information given in this data
sheet is not intended to be exhaustive. As conditions of
use, method of application and suitability of the substrate
prior to painting are beyond our control, no guarantee is
implied by the recommendations contained in this sheet.
It is the user’s responsibility to ensure that our
comprehensive application instructions are read in
conjunction with this datasheet prior to using the product.
The information contained in this sheet is liable to
modification from time to time in the light of experience and
on-going product development programmes. Issue 11/2014
Pool Solutions Epoxy Coatings | 083 455 9632 |Email: [email protected] |Web: www.poolsolutions.co.za