i-PAC12-1 Tigertec® Silver - ISO P Generation The Rocket 1 © by Walter AG Tigertec® Silver - ISO P Generation Product features NEW: ISO P Geometries Large chip breaking range NEW: Aluminiumoxide with optimised microstructure Increase wear resistance Higher cutting speed NEW: Mechanical post-treatment Higher toughness NEW: Silver flank face Easy wear detection NEW: Microedge-Technology Longer tool life 2 NEW: Ground seating surface after coating Process reliability © by Walter AG Tigertec® Silver - ISO P Generation Complete geometry family • FP5 – Finishing – Steel • MP3 – Medium machining – Long chipping steel • MP5 – Medium machining – Steel in general • RP5 – Roughing – Steel 3 January 2012 | VM | Kussmaul © by Walter AG Tigertec® Silver - ISO P Generation Geometry MP5 Universal, stable three-center curve cutting edge Suitable from continues to interrupted cuts Reinforced chip breaker blades in the radius area Improved chip control for small depth of cut Increases the tool life / decrease the wear Open groove on the main cutting edge Soft cutting also on high depth of cut 4 July 2011 | VM | Drobniewski | Kußmaul © by Walter AG Tigertec® Silver - ISO P Generation Application area – MP5 • Medium machining steel in general – Universal geometry for a large range of different steels – Largest chip breaking area of all inserts. – From continuous cutting on bar stock and also machining interrupted cuts. – Most sold insert for machining steel – first choice. • Industry – – – – General machining Job shops Dealers “love” this insert … but also used in mass production • Typical cutting data – ap: 0,8 – 5,0mm – f: 0,20 – 0,60mm 5 © by Walter AG Tigertec® Silver - ISO P Generation Geometry RP5 Stable, positive 3 chamfer Roughing with low power consumption Open, deep and wide chip groove Low cutting temperature Reduced wear in comparison with previous geometries Wider chamfer in the center region of the main cutting edge Prevents chipping when machining skins or forged components 6 July 2011 | VM | Drobniewski | Kußmaul © by Walter AG Tigertec® Silver - ISO P Generation Geometry RP5 2 1 1 2 Additional application area of the RP5 in comparison to the NM9 geometry 7 January 2012 | VM | Kussmaul © by Walter AG Lab test RP5 Crater wear / Flank wear Version 1 Version 2 C45 (680 N/mm²) C45 (680 N/mm²) Insert: CNMG120408 CNMG120408 Grade: ISO P10 ISO P10 PCLNL3225M12 PCLNL3225M12 vc 290 350 [m/min] f 0,32 0,32 [mm] ap 2,5 2,5 [mm] Coolant No No Material Tool: Cutting data: 8 January 2012 | VM | Kussmaul Vc +20% © by Walter AG Available Tigertec® Silver inserts NRF FP5 9 January 2012 | VM | Kussmaul MP3 MP5 NRR RP5 © by Walter AG Tigertec® Silver CNMG / CNMM 10 January 2012 | VM | Kussmaul © by Walter AG Tigertec® Silver DNMG / DNMM 11 January 2012 | VM | Kussmaul © by Walter AG Tigertec® Silver SNMG / SNMM 12 January 2012 | VM | Kussmaul © by Walter AG Tigertec® Silver TNMG / TNMM VNMG 13 January 2012 | VM | Kussmaul © by Walter AG Tigertec® Silver WNMG / WNMM 14 January 2012 | VM | Kussmaul © by Walter AG
© Copyright 2026 Paperzz