Home and Closet Organization
Wall Beds by Häfele
• Forverticalfoldingbeds
• Spacesaving–idealforlofts,guestbeds,homeoffice,
hospitals, etc.
• Availablein3sizesformattresses: Single/Twin: 75”x39”
Double/Full: 75”x54”
Queen:
80”x60”
• Sturdy,torsion-freesteelframewithconcealedgasstruts
• Includesintegratedfoldingfeet,whichautomaticallyextendas
bed is opened and retract when closing
• Withwoodslattedmattresssupportsmountedinflexible
sockets for comfort
• Recommendedforrelativelylightfoammattresses,withoutbox
springs,6”–10”thick
• Includesdrillingtemplateforproperalignmentandinstallation
of hardware
• Caseworktobeconstructedbyenduser
• Minimuminsidedepthofcase:470–600mm(181/2”–235/8”)
Note
Successful and safe installation of fitting set and construction of
caseworkrequiresaprofessionalskilllevel.Caseworktobeconstructed
ofhighqualitymaterial(preferablyhighqualityplywood),minimum
thickness3/4”.Cabinetmustbesafelysecuredagainsttipping(set
includes2pcs.securityattachmentbrackets).
4
Wall bedinstallationhasneverbeensoeasyandsafe.Häfele’s
Wall bed system comes complete with pre-mounted fittings and
can be installed in 4 easy steps.
Min. 470 (18 1/2”) 600 (23 5/8”)
B
Floor to
top of
slats
C approx.
A
108
Toe kick
95 (3 3/4”) (4 1/4”)
1. Mark drilling position on both panels with the aid of the included
drilling template.
2.Drill6holesineachsidepanel.
3. Fasten the two support brackets with the screws provided.
4. Slide bed frame onto support brackets, tighten screws, and attach
the front panel.
330
(13”)
20
(13/16")
Dimensional data not binding. We reserve the right to alter specifications without notice.
96
(3 25/32")
55
(2 3/16")
69
(2 23/32")
Wall Bed
40
(1 9/16")
15
(9/16")
70
(2 3/4")
55
(2 3/16")
26
(1")
106
(4 11/64")
Material:Steel;Finish:Frame:blackepoxy:Foldingfeet:silverepoxy
Slats: Laminated Beech;Finish:naturallacquered
Mattress
Single/Twin
Double/Full
Queen
sizes
75”x39”
75”x54”
80”x60”
Cabinet construction inside dimensions
A-inside height
B-inside width
2018(797/16”)
1051(413/8”)
2018(797/16”)
1432(563/8”)
2145(847/16”)
1584(623/8”)
Supplied With
Complete frame
Mounting brackets and hardware
2 Safety brackets
Mounting instructions
C-protrusion
1725(68”)
1725(68”)
1852(73”)
ItemNo.
271.92.016
271.92.025
271.92.132
3 Bed straps
Mattress retainer
Drillingtemplate
Single/Twin
Double/Full
Queen
Mattress weight
16–22kg(35–48lbs)
23–31kg(50–68lbs)
27–36kg(60–80lbs)
• Securesfoldingbedstowall
• Thespecialdesignensuresthatforce
is distributed evenly over all the
mounting bolts offering adjustability
for alignment
• Theswivelingwallplatepermits
straightforward mounting in any
position.
Material: Steel, galvanized
ItemNo.
271.98.100
General Weight Parameters
Front panel weight
approx.27kg(60lbs)
approx.38kg(84lbs)
approx.45kg(100lbs)
Additional “Safe”
Safety Brackets
Combined lifting capacity
43–49kg(95-108lbs)
61–69kg(134–152lbs)
72–81kg(160-180lbs)
Note
Wall bed will not operate properly unless the above weight ranges are adhered to.
Supplied With
Mounting bolts
Note
TocomplywithDIN68873,foldaway
beds must be installed with a minimum
of two safety fittings.
Dimensions in mm
Inches are approximate
www.hafele.com
FC
4.7
Mounting Instructions
Item No.: 271.92.xxx
Wall-Beds
1
General Notes
• For vertical folding beds
• Successful and safe installation of Bed-Lift and construction of casework requires a professional skill level
• All Casework must be constructed from high quality material, preferably high-quality plywood
• All Casework must be perfectly square and plumb for Bed-Lift to operate properly
• Minimum material thickness:
3/4” (19 mm)
• Minimum inside cabinet depth:
18 1/2” (470 mm)
• Maximum Mattress thickness:
6” (152 mm) - 10” (254 mm)
• Cabinet must be safely secured against tipping (set includes 2 pcs security attachment brackets)
• Please use the included drilling template to accurately locate holes for Mounting Brackets.
Bed-Lift Options
Mattress Dimensions
• Item No 271.92.016 will accommodate Single/Twin mattresses
75” x 39” (1905 x 991 mm)
• Item No 271.92.025 will accommodate Double/Full mattresses
75” x 54” (1905 x 1372 mm)
• Item No 271.92.132 will accommodate Queen mattresses
80” x 60” (2032 x 1524 mm)
General Weight Parameters:
Front Panel Weight
Mattress Weight
Single/Twin
approx. 27 kgs (60 lbs)
16 - 22 kgs (35 - 48 lbs)
Double/Full
approx. 38 kgs (84l bs)
23 - 31 kgs (50 - 68 lbs)
Queen
approx. 45 kgs (100 lbs)
27 - 36 kgs (60 - 80 lbs)
Bed-lift will not operate properly unless the above weight ranges are adhered to.
Combined Lifting Capacity
43 - 49 kgs (95 - 108 lbs)
61 - 69 kgs (134 - 152 lbs)
72 - 81 kgs (160 - 180 lbs)
Fitting Set Consists of:
• 2 pcs. Security Attachment Brackets w/ bolt, washer, nut, and wood screw for attachment.
• 2 sets Mounting Brackets with attachment bolts x 12 pcs.
• 4 pcs. Z-Brackets for initial attachment (hanging) of Front Panel; 10 pcs. wood screws for attachment.
• 2 pcs. M4 round head machine screws used as Front Panel adjustment screws in Z-Brackets.
• 3 sets Mattress Straps for securing Mattress.
• 1 pc. chrome-plated wire Mattress Stop with mounting hardware; 2 pcs. washers and capped nuts.
• Drilling Template.
Please order separately:
• Handle(s) for Front Panel to pull down bed.
2
Casework
• See below chart for appropriate dimensions
• Refer to Drawing #1 for details
Mattress Sizes
Single/Twin
Double/Full
Queen
75” x 39”
75” x 54”
80” x 60”
Cabinet Construction Inside Dimensions
Inside Height
Inside Width
Min. Inside Depth
2018 mm (79 7/16”)
2018 mm (79 7/16”)
2145 mm (84 7/16”)
1051 mm (41 3/8”)
1432 mm (56 3/8”)
1584 mm (62 3/8”)
470 mm (18 1/2”)
470 mm (18 1/2”)
470 mm (18 1/2”)
Toe Kick
76 mm (3”) x 1051 mm (41 3/8”)
76 mm (3”) x 1432 mm (56 3/8”)
76 mm (3”) x 1584 mm (62 3/8”)
* Front Panel Dimensions
Height
Width
Single/Twin
Double/Full
Queen
1934 mm(76 1/8”)
1934 mm(76 1/8”)
2061 mm (81 1/8”)
1043 mm (41 1/16”)
1424 mm (56 1/16”)
1576 mm (62 1/16”)
Please Note:
• All recommended dimensions above are total to include any edge banding or face frames.
• All dimensions are based on 3/4” material.
• Front Panel dimensions allow for a 3/16” (4 mm) gap around all sides.
• See Drawing #2 - If optional Top and Bottom details are prefered, adjust appropriate dimensions on your own.
• A Back Panel for the Cabinet is not included in these instructions, if desired please calculate on your own.
* Recommendation:
Before cutting Front Panel, build and mount cabinet securely to wall.
Be sure Cabinet is square and plumb.
Install Bed-lift to ensure all is functioning properly.
Measure and fit Front Panel inside of opening.
Instructions
• Construct Cabinet per Drawing #1.
• Be sure Kick is beveled, approx. 45° - see bottom detail(s) Drawing #2.
• Attach Cabinet securely to the wall and any surrounding Casework.
• Use included Security Brackets, see Drawing #3.
• Cabinet must be installed absolutely square and plumb.
• Align Drilling Template on inside Cabinet, mark and drill 6 x’s Ø8.5 mm (5/16”) through holes, see Drawing #3.
• Countersink holes on outside edges.
• Fasten the two Mounting Brackets with provided bolts as in Drawings #2 & #3.
3
Installation
• 2 people are recommended for installation.
• Slide Bed Frame onto Mounting Brackets and hook over the studs, see Drawing #3.
• Fold Bed Frame up to vertical position until holes align, insert remaining 4 bolts and tighten securely.
Caution: Before testing be absolutely sure cabinet is securely anchored to the wall and surrounding millwork. At this
point bed frame will be difficult to pull down, and conversely will spring up very quickly, be careful! Only after
additional & appropriate weight of front panel & mattress is added will ease of operation be achieved. Keep
fingers clear from folding feet and mechanism while testing.
Mounting Front Panel to Frame
• Please refer to Drawing #4
• Front panel should be sized to allow for a 4 mm (3/16”) gap around all edges (see Front Panel dimensions in CASEWORK Section).
• Screw 2 pcs. M4 round headed screws in to top of 2 pcs. of the Z-Brackets, these will be used to adjust and align front panel.
• Attach Z-Brackets to back side of Front Panel.
• Hang Front Panel over top and bottom rails.
• Close bed, check for alignment and adjust via M4 screws as necessary.
• After final adjustment and alignment is achieved, lock Front Panel down with additional wood screws (not included) through
holes in metal frames, see Drawing #4. Front Panel must be securely fastened to Frame.
• Install wood blocks as stops on both sides of cabinet to ensure the bed closes absolutely vertical, see Drawing #1.
Do not install one continuous stop across the top, as this may interfere with the folding feet.
• Attach chrome Mattress Stop through the two holes in bottom frame using the capped nuts and washers provided.
Mattress stop keeps the mattress from sliding down as the bed is folded vertical.
• Place mattress on frame and secure with 3 sets bedding straps.
Loop curved clasp around frame, through square metal ring and pull tight. Repeat with remaining straps.
Stretch straps over mattress hooking round rings inside one another.
• Install Handle(s), (not included), to front panel to pull bed frame down.
4
mi
n .3
/4 "
Drawing #1
IN
D
SI
E
CA
BI
N
W
ET
ID
TH
Cabinet
INS IDE CABINET HEI GHT
STOPS
N
M I ID E H
S
T
IN E P 1 /2 "
D 8
1
KICK
WIDTH
Front panel
HEIGHT
5
Drawing #2
TOP PANEL
TOP PANEL
4mm
[3/16"]
WOOD BLOCK
AS STOP
OPTIONAL
6x
64
8 THRU
 17 X 90,0°
32
32
32
FRONT PANEL
Use these two holes
to mount brackets to
inside of cabinet.
64
96
19
[3/4 in]
32
32
64
4
[3/16 in]
97
161
129
apprx.45°
TOE KICK
IMPORTANT
This diagram is not to scale.
It has been reduced.
76
[3 in]
95
[3 3/4 in]
19
[3/4 in]
BOTTOM PANEL
95 [3 3/4"]
OPTIONAL
BOTTOM PANEL
6
Drawing #3
SECURITY ATTACHMENT BRACKETS
FINAL
LOCKING
SCREW
7
Diagram 1
Diagram 2
Diagram 3
Diagram 4
Drawing #4
FRONT PANEL ADJUSTMENT
AFTER FRONT PANEL IS
PROPERLY ALIGNED-LOCK
DOWN WITH ADDITIONAL SCREWS
THROUGH HOLES IN FRAME.
A P 1 4 "(
PR 355
OX )
.
Dimension X
Single/Double=1503mm(59 3/16")
Queen=1630mm(64 3/16")
X
M4 adjustment screw
A P 3 "(
PR 7 5 )
OX
.
FRONT- TOP
INSERT M4 ADJUSTMENT SCREW IN
TOP TWO Z-BRACKETS
1-800-423-3531 • www.hafele.com
8