Lifting Bolts
Lifting Bolts
Introduction
Swivel Lifting Rings and Lifting Bolts
Our swivel lifting rings fully comply with the EC directive 2006/42/EC. They are CE marked
and are supplied with a Certificate of Conformity. There is a 100% check on anti-cracking,
a proof load test of 2.5 x load limit and a safety factor of 5 on most parts. Each ring is
individually marked to ensure full product traceability.
The Swivel Lifting Rings come in three main forms – depending on the number of axis
required to swivel. The most popular type is the double swivel rings.
Double swivel
Triple swivel
Threads M8 – M48
Loads 0,3 tons
to 15 tons
Threads M4 – M100
Loads 0,05 tons
to 50 tons
Threads M8 – M56
Loads 0,3 tons
to 22 tons
Other Standard Lifting Bolts
45°
90°
Do not lift
Do not lift
Standard lifting bolts
Hi-tensile lifting bolts
DIN 580 & DIN 582
Standard lifting bolts (to DIN 580 and DIN 582)
These are CE marked and are available with male or female threads in either steel or stainless
steel (A4 AISI 316). They are meant only for linear loading of the bolts at a maximum
angle of 45° from the thread. They are not meant for loads that might swivel.
These are supplied with a generic CE Certificate of Conformity stating that the parts have
been manufactured to the relevent DIN standard and therefore suitable for lifting.
High-tensile lifting bolts
The High-tensile lifting bolts are similar to the standard lifting bolts but are rated at higher
loads and can lift loads at up to 90° from the thread. They are not meant for loads that
might swivel.
Tel: 01483 26 67 76
Fax: 01483 26 67 75
Lifting Bolts from Automotion Components
Single swivel
web: mechanicalcomponents.co.uk
a website from Automotion Components
741
Lifting Bolts
Product Overview
Swivel Lifting Rings
Swivel lifting rings operating instructions
•
•
•
Lifting Bolts from Automotion Components
•
•
•
•
•
•
•
•
•
•
Ensure all lifting bolts are CE marked.
Ensure they are handled by qualified personnel.
Refer to the operating instructions particularly with regards to product selection,
any possibility of the load swivelling, the effect of lifting angles on the load capacity
(see relevant tables), etc.
Never allow any personnel underneath a suspended load.
Always heed the load rating of the lifting bolt.
Always perform a visual inspection of the lifting rings prior to use. Checking for any
damage to thread and/or swivelling system. Check for wear or corrosion, signs of stress
or bending. Check CE mark and load rating.
Ensure a yearly full service inspection is performed.
Always ensure the full bottom face of the lifting bolts is in contact with a smooth,
square surface.
Ensure bolt is tightened to the correct torque.
Ensure full and unrestricted movement of the lifting ring in all directions.
Before each lift ensure the correct orientation of the shackle in the lift direction.
Avoid using our standard steel lifting rings in corrosive environments eg sandy, chemical,
acid, moisture etc. In this case consider using our stainless steel lifting rings.
Note the thread length requirements:
- 1 x thread diameter for steel (ST37 min.).
- 1.25 x thread diameter for cast iron.
- 2 x thread diameter for aluminium.
- 2.5 x thread diameter for other light metals.
- If fixing into low resistance material it is better to allow for a bigger diameter
thread to compensate for the lower material resistance.
Note: The full thread must be engaged. Longer thread lengths can be supplied on request or a bolt and
washer/nut combination can be used.
Temperature extremes
-40°C to -20°C
Load rating reduces by 20%.
+200°C to +300°C Load rating reduces by 10%.
0%.
+300°C to +400°C Load rating reduces by 25%.
5%.
Rugged
CERTIFIC
ATE
CERTIFIC
ATE OF CO
Name and
addr
representativ ess of manufacturer or
their
e:
For harsh environments we recommend the use
of our stainless steel lifting rings.
Description
Automotion
Components
Ltd
Alexia Hous
e, Little Mea
d Indu
Cranleigh, Surr
ey, GU6 8NE strial Estate
(UK)
of the part
Lifting Equi
pment
The part is
in complian
ce with the
European direc
tive:
2006/42/CE
European stan
dards used
:
Certificate of
conformity
P4020
N
E
IM
EN ISO 1210
0-1 & 2, EN
ISO 13852,
EN 1677-1
No.:
No. 090311/1
60-164
Ring type and
dimension:
P4020 – DSR
M20
Standard ring?
Threads M8 – M30
Loads 0,3 tons to 3 tons.
C
E
P
Yes
Quantity:
5
Colour:
Red
S
Material:
Treated, forge
d steel alloy
fatigue resis
, hardened
, tempered
tance
,
Manufacturer
’s mark:
Shackle: AR
Bolt: RI 05
WLL = Wor
king load limit
:
(maximum
load – refer
to tables)
P4022
NFORMITY
2,5 tons
Magnetic testi
ng:
Threads M30 – M45
Loads 3,5 tons to
6 tons.
Yes - 100%
Testing to brea
king load by
batch:
sampling from
production
WLL x 5
Customer:
John Doe Ltd.
Order:
SOR0099
999
The swivel
rings must
be used in
accordance
As all tests
with our recom
have produ
mendations
ced satisfactory
explained in
results; we
the technical
have consid
literature
ered these
parts to be
“good for utilisa
tion”
.
Signature:…
742
Tel: 01483 26 67 76
Fax: 01483 26 67 75
………………
………………
………………
……………
Date:…………
………………
………….
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
Technical Information
Product information
Product marking
Compliant with 2006/42/EC, and with individual date of manufacture and batch number.
Complies with 2006/42/CE
Model No.
WLL weight limit
Individual part no.
date of manufacture
Lifting angles
45°
60°
Load
Load
Load
100% of load rating
of bolt
Approx 66% of load
rating of bolt
Approx 50% of load
rating of bolt
For full information on lifting arrangements see technical pages
Steel and Stainless steel (316) versions
Steel
Lifting Bolts from Automotion Components
CE mark
Stainless (316L)
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
743
Lifting Bolts
Technical Information
Installation information
Lifting Bolts from Automotion Components
744
After installation, check
the hoist ring to be sure it
swivels and pivots freely in
all directions.
The side of the ring must not
contact anything.
Never use an oversized hook or
other lifting device which will
pry or tend to open the “U“
shaped bar on centre pull hoist
rings.
Always ensure full thread
engagement when installing
hoist rings.
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
Technical Information
Single Swivel Lifting Rings
P4002 Male
P4004 Female
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
Part no.
Thread
P4002.M008 & P4004.M008
M8
0,30 tons
0,60 tons
0,30 tons
0,60 tons
0,40 tons
0,30 tons
0,60 tons
0,30 tons
P4002.M010 & P4004.M010
M10
0,60 tons
1,20 tons
0,60 tons
1,20 tons
0,80 tons
0,60 tons
1,30 tons
0,60 tons
P4002.M012 & P4004.M012
M12
1,00 tons
2,00 tons
1,00 tons
2,00 tons
1,40 tons
1,00 tons
2,10 tons
1,00 tons
P4002.M016 & P4004.M016
M16
1,60 tons
3,20 tons
1,60 tons
3,20 tons
2,20 tons
1,60 tons
3,40 tons
1,60 tons
P4002.M020 & P4004.M020
M20
2,50 tons
5,00 tons
2,50 tons
5,00 tons
3,50 tons
2,50 tons
5,30 tons
2,50 tons
P4002.M024 & P4004.M024
M24
4,00 tons
8,00 tons
4,00 tons
8,00 tons
5,60 tons
4,00 tons
8,40 tons
4,00 tons
P4002.M030 & P4004.M030
M30
6,30 tons 12,60 tons 6,30 tons 12,60 tons 8,80 tons
P4002.M036 & P4004.M036
M36
10,00 tons 20,00 tons 10,00 tons 20,00 tons 14,00 tons 10,00 tons 21,00 tons 10,00 tons
P4002.M042
M42
12,50 tons 25,00 tons 12,50 tons 25,00 tons 17,50 tons 12,50 tons 26,30 tons 12,50 tons
P4002.M048
M48
15,00 tons 30,00 tons 15,00 tons 30,00 tons 21,00 tons 15,00 tons 31,50 tons 15,00 tons
Tel: 01483 26 67 76
Fax: 01483 26 67 75
6,30 tons 13,20 tons 6,30 tons
web: mechanicalcomponents.co.uk
a website from Automotion Components
745
Lifting Bolts
Technical Information
Double Swivel Lifting Rings
P4005 Male
P4006 Female
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
Part no.
Thread
P4005.M004
M4
0,050 tons 0,100 tons 0,050 tons 0,100 tons 0,070 tons 0,050 tons 0,100 tons 0,050 tons
P4005.M005
M5
0,075 tons 0,150 tons 0,075 tons 0,150 tons 0,100 tons 0,075 tons 0,150 tons 0,075 tons
P4005.M006
M6
0,100 tons 0,200 tons 0,100 tons 0,200 tons 0,140 tons 0,100 tons 0,200 tons 0,100 tons
P4005.M008 & P4006.M008
M8
0,30 tons
0,60 tons
0,30 tons
0,60 tons
0,40 tons
0,30 tons
0,60 tons
0,30 tons
P4005.M010 & P4006.M010
M10
0,60 tons
1,20 tons
0,60 tons
1,20 tons
0,80 tons
0,60 tons
1,30 tons
0,60 tons
P4005.M012 & P4006.M012
M12
1,00 tons
2,00 tons
1,00 tons
2,00 tons
1,40 tons
1,00 tons
2,10 tons
1,00 tons
P4005.M014 & P4006.M014
M14
1,30 tons
2,60 tons
1,30 tons
2,60 tons
1,80 tons
1,30 tons
2,70 tons
1,30 tons
P4005.M016 & P4006.M016
M16
1,60 tons
3,20 tons
1,60 tons
3,20 tons
2,20 tons
1,60 tons
3,40 tons
1,60 tons
P4005.M018 & P4006.M018
M18
2,00 tons
4,00 tons
2,00 tons
4,00 tons
2,80 tons
2,00 tons
4,20 tons
2,00 tons
P4005.M020 & P4006.M020
M20
2,50 tons
5,00 tons
2,50 tons
5,00 tons
3,50 tons
2,50 tons
5,30 tons
2,50 tons
P4005.M022 & P4006.M022
M22
3,00 tons
6,00 tons
3,00 tons
6,00 tons
4,20 tons
3,00 tons
6,30 tons
3,00 tons
P4005.M024
M24
4,00 tons
8,00 tons
4,00 tons
8,00 tons
5,60 tons
4,00 tons
8,40 tons
4,00 tons
P4005.M027
M27
5,00 tons 10,00 tons 5,00 tons 10,00 tons 7,00 tons
5,00 tons 10,50 tons 5,00 tons
P4005.M030
M30
6,30 tons 12,60 tons 6,30 tons 12,600 tons 8,8 tons
6,30 tons 13,20 tons 6,30 tons
P4005.I031 & P4006.I031
(UNC 5/16”-18)
650 lbs
1,300 lbs
650 lbs
1,300 lbs
910 lbs
650 lbs
1,365 lbs
650 lbs
P4005.I037 & P4006.I037
(UNC 3/8”-16)
1,200 lbs
2,400 lbs
1,200 lbs
2,400 lbs
1,680 lbs
1,200 lbs
2,520 lbs
1,200 lbs
P4005.I050 & P4006.I050
(UNC 1/2”13)
2,200 lbs
4,400 lbs
2,200 lbs
4,400 lbs
3,080 lbs
2,200 lbs
4,620 lbs
2,200 lbs
P4005.I063 & P4006.I063
(UNC 5/8”-11)
3,800 lbs
7,600 lbs
3,800 lbs
7,600 lbs
5,320 lbs
3,800 lbs
7,980 lbs
3,800 lbs
P4005.I075 & P4006.I075
(UNC 3/4”-10)
5,500 lbs
11,000 lbs
5,500 lbs
11,000 lbs
7,700 lbs
5,500 lbs
11,550 lbs
5,500 lbs
P4005.I088 & P4006.I088
(UNC 7/8”-9)
6,600 lbs
13,200 lbs
6,600 lbs
13,200 lbs
9,240 lbs
6,600 lbs
13,860 lbs
6,600 lbs
P4005.I100
748
(UNC 1”-8)
10,000 lbs 20,000 lbs 10,000 lbs 20,000 lbs 14,000 lbs 10,000 lbs 21,000 lbs 10,000 lbs
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
Technical Information
Stainless Steel Double Swivel Lifting Rings
P4020 Male
P4021 Female
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
Part no.
Thread
P4020.M008 & P4021.M008
M8
0,30 tons
0,60 tons
0,30 tons
0,60 tons
0,40 tons
0,30 tons
0,60 tons
0,30 tons
P4020.M009
M8
0,30 tons
0,60 tons
0,30 tons
0,60 tons
0,40 tons
0,30 tons
0,60 tons
0,30 tons
P4020.M010 & P4021.M008
M10
0,50 tons
1,00 tons
0,50 tons
1,00 tons
0,70 tons
0,50 tons
1,10 tons
0,50 tons
P4020.M011
M10
0,50 tons
1,00 tons
0,50 tons
1,00 tons
0,70 tons
0,50 tons
1,10 tons
0,50 tons
P4020.M012 & P4021.M008
M12
0,80 tons
1,60 tons
0,80 tons
1,60 tons
1,10 tons
0,80 tons
1,70 tons
0,80 tons
P4020.M013
M12
0,80 tons
1,60 tons
0,80 tons
1,60 tons
1,10 tons
0,80 tons
1,70 tons
0,80 tons
P4020.M014 & P4021.M008
M14
1,00 tons
2,00 tons
1,00 tons
2,00 tons
1,40 tons
1,00 tons
2,10 tons
1,00 tons
P4020.M016 & P4021.M008
M16
1,50 tons
3,00 tons
1,50 tons
3,00 tons
2,10 tons
1,50 tons
3,20 tons
1,50 tons
P4020.M018 & P4021.M008
M18
1,50 tons
3,00 tons
1,50 tons
3,00 tons
2,10 tons
1,50 tons
3,20 tons
1,50 tons
P4020.M020 & P4021.M008
M20
1,60 tons
3,20 tons
1,60 tons
3,20 tons
2,20 tons
1,60 tons
3,40 tons
1,60 tons
P4020.M022 & P4021.M008
M22
2,00 tons
4,00 tons
2,00 tons
4,00 tons
2,80 tons
2,00 tons
4,20 tons
2,00 tons
P4020.M024
M24
2,70 tons
5,40 tons
2,70 tons
5,40 tons
3,80 tons
2,70 tons
5,70 tons
2,70 tons
P4020.M027
M27
2,80 tons
5,60 tons
2,80 tons
5,60 tons
3,90 tons
2,80 tons
5,90 tons
2,80 tons
P4020.M030
M30
3,00 tons
6,00 tons
3,00 tons
6,00 tons
4,20 tons
3,00 tons
6,30 tons
3,00 tons
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
749
Lifting Bolts
Technical Information
Heavy Duty Double Swivel Lifting Rings
P4008 Male
P4010 Female
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
9,00 tons
4,50 tons
9,00 tons
6,30 tons
4,50 tons
9,50 tons
4,50 tons
Part no.
Thread
P4008.M024 & P4010.M024
M24
4,50 tons
P4010.M027
M27
5,00 tons 10,00 tons 5,00 tons 10,00 tons 7,00 tons
P4008.M030 & P4010.M030
M30
7,30 tons 14,60 tons 7,30 tons 14,60 tons 10,20 tons 7,30 tons 15,30 tons 7,30 tons
P4008.M033 & P4010.M033
M33
8,00 tons 16,00 tons 8,00 tons 16,00 tons 11,20 tons 8,00 tons 16,80 tons 8,00 tons
P4008.M036 & P4010.M036
M36
10,00 tons 20,00 tons 10,00 tons 20,00 tons 14,00 tons 10,00 tons 21,00 tons 10,00 tons
P4008.M037
M36
10,00 tons 20,00 tons 10,00 tons 20,00 tons 14,00 tons 10,00 tons 21,00 tons 10,00 tons
P4008.M039 & P4010.M039
M39
10,00 tons 20,00 tons 10,00 tons 20,00 tons 14,00 tons 10,00 tons 21,00 tons 10,00 tons
P4008.M042 & P4010.M042
M42
12,50 tons 25,00 tons 12,50 tons 25,00 tons 17,50 tons 12,50 tons 26,30 tons 12,50 tons
P4008.M043
M42
12,50 tons 25,00 tons 12,50 tons 25,00 tons 17,50 tons 12,50 tons 26,30 tons 12,50 tons
P4008.M045 & P4010.M045
M45
15,00 tons 30,00 tons 15,00 tons 30,00 tons 21,00 tons 15,00 tons 31,50 tons 15,00 tons
P4008.M048 & P4010.M048
M48
20,00 tons 40,00 tons 20,00 tons 40,00 tons 28,00 tons 20,00 tons 42,00 tons 20,00 tons
P4008.M049
M48
20,00 tons 40,00 tons 20,00 tons 40,00 tons 28,00 tons 20,00 tons 42,00 tons 20,00 tons
P4008.M050
M50
20,00 tons 40,00 tons 20,00 tons 40,00 tons 28,00 tons 20,00 tons 42,00 tons 20,00 tons
P4008.M052 & P4010.M052
M52
20,00 tons 40,00tons 20,00 tons 40,00tons 28,00 tons 20,00 tons 42,00 tons 20,00 tons
P4008.M056
M56
25,00 tons 50,00 tons 25,00 tons 50,00 tons 35,00 tons 25,00 tons 52,50 tons 25,00 tons
P4008.M057
M56
25,00 tons 50,00 tons 25,00 tons 50,00 tons 35,00 tons 25,00 tons 52,50 tons 25,00 tons
P4008.M064
M64
32,10 tons 64,20 tons 32,10 tons 64,20 tons 44,90 tons 32,10 tons 67,40 tons 32,10 tons
P4008.M065
M65
32,10 tons 64,20 tons 32,10 tons 64,20 tons 44,90 tons 32,10 tons 67,40 tons 32,10 tons
P4008.M072
M72
25,00 tons 50,00 tons 25,00 tons 50,00 tons 35,00 tons 25,00 tons 52,50 tons 25,00 tons
P4008.M073
M72
25,00 tons 50,00 tons 25,00 tons 50,00 tons 35,00 tons 25,00 tons 52,50 tons 25,00 tons
P4008.M080
M80
32,10 tons 64,20 tons 32,10 tons 64,20 tons 44,90 tons 32,10 tons 67,40 tons 32,10 tons
P4008.M090
M90
32,10 tons 64,20 tons 32,10 tons 64,20 tons 44,90 tons 32,10 tons 67,40 tons 32,10 tons
P4008.M100
M100
32,10 tons 64,20 tons 32,10 tons 64,20 tons 44,90 tons 32,10 tons 67,40 tons 32,10 tons
(UNC 1”-8)
10,000 lbs 20,000 lbs 10,000 lbs 20,000 lbs 14,000 lbs 10,000 lbs 21,000 lbs 10,000 lbs
(UNC 1 1/4”-7)
14,000 lbs 28,000 lbs 14,000 lbs 28,000 lbs 19,600 lbs 14,000 lbs 29,400 lbs 14,000 lbs
P4010.I100
P4008.I125 & P4010.I125
P4008.I137 & P4010.I137
5,00 tons 10,50 tons 5,00 tons
(UNC 1 3/8”-6*) 20,000 lbs 40,000 lbs 20,000 lbs 40,000 lbs 28,000 lbs 20,000 lbs 42,000 lbs 20,000 lbs
P4008.I150 & P4010.I150
(UNC 1 1/2”-6)
20,000 lbs 40,000 lbs 20,000 lbs 40,000 lbs 28,000 lbs 20,000 lbs 42,000 lbs 20,000 lbs
P4008.I200 & P4010.I200
(UNC 2”-4 1/2)
50,000 lbs 100,000 lbs 50,000 lbs 100,000 lbs 70,000 lbs 50,000 lbs 105,000 lbs 50,000 lbs
750
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
Technical Information
Heavy Duty (Mega) Double Swivel Lifting Rings
P4011 Male
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
Part no.
Thread
P4011.M064
M64
33,00 tons 66,00 tons 33,00 tons 66,00 tons 46,00 tons 33,00 tons 69,00 tons 33,00 tons
P4011.M072
M72
35,00 tons 70,00 tons 35,00 tons 70,00 tons 49,00 tons 35,00 tons 74,00 tons 35,00 tons
P4011.M073
M72
35,00 tons 70,00 tons 35,00 tons 70,00 tons 49,00 tons 35,00 tons 74,00 tons 35,00 tons
P4011.M080
M80
40,00 tons 80,00 tons 40,00 tons 80,00 tons 56,00 tons 40,00 tons 84,00 tons 40,00 tons
P4011.M090
M90
45,00 tons 90,00 tons 45,00 tons 90,00 tons 63,00 tons 45,00 tons 95,00 tons 45,00 tons
P4011.M100
M100
50,00 tons 100,00 tons 50,00 tons 100,00 tons 70,00 tons 50,00 tons 105,00 tons 50,00 tons
P4011.I225
(UNC 2”1/4-4)
55,000 lbs 110,00 lbs 55,000 lbs 110,000 lbs 77,000 lbs 55,000 lbs 115,500 lbs 55,000 lbs
P4011.I250
(UNC 2”1/2-4)
70,000 lbs 140,000 lbs 70,000 lbs 140,000 lbs 98,000 lbs 70,000 lbs 147,000 lbs 70,000 lbs
P4011.I275
(UNC 2”3/4-4)
75,000 lbs 150,000 lbs 75,000 lbs 150,000 lbs 105,000 lbs 75,000 lbs 157,500 lbs 75,000 lbs
P4011.I300
(UNC 3”-4)
80,000 lbs 160,000 lbs 80,000 lbs 160,000 lbs 112,000 lbs 80,000 lbs 168,000 lbs 80,000 lbs
P4011.I325
(UNC 3”1/4-4)
90,000 lbs 180,000 lbs 90,000 lbs 180,000 lbs 126,000 lbs 90,000 lbs 189,000 lbs 90,000 lbs
P4011.I350
(UNC 3”1/2-4)
95,000 lbs 190,000 lbs 95,000 lbs 190,000 lbs 133,000 lbs 95,000 lbs 199,500 lbs 95,000 lbs
P4011.I375
(UNC 3”3/4-4) 100,000 lbs 200,000 lbs 100,000 lbs 200,000 lbs 140,000 lbs 100,000 lbs 210,000 lbs 100,000 lbs
P4011.I400
(UNC 4”-4)
110,000 lbs 220,000 lbs 110,000 lbs 220,000 lbs 154,000 lbs 110,000 lbs 231,000 lbs 110,000 lbs
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
751
Lifting Bolts
Technical Information
Heavy Duty Stainless Steel Double Swivel Lifting Rings
P4022 Male
P4023 Female
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
Part no.
Thread
P4023.M024
M24
2,70 tons
5,40 tons
2,70 tons
5,40 tons
3,80 tons
2,70 tons
5,70 tons
2,70 tons
P4023.M027
M27
2,80 tons
5,60 tons
2,80 tons
5,60 tons
3,90 tons
2,80 tons
5,90 tons
2,80 tons
P4022.M030 & P4023.M30
M30
3,50 tons
7,00 tons
3,50 tons
7,00 tons
4,90 tons
3,50 tons
7,30 tons
3,50 tons
P4022.M033 & P4023.M33
M33
3,50 tons
7,00 tons
3,50 tons
7,00 tons
4,90 tons
3,50 tons
7,30 tons
3,50 tons
P4022.M036 & P4023.M36
M36
5,00 tons 10,00 tons 5,00 tons 10,00 tons 7,00 tons
5,00 tons 10,50 tons 5,00 tons
P4022.M037
M36
5,00 tons 10,00 tons 5,00 tons 10,00 tons 7,00 tons
5,00 tons 10,50 tons 5,00 tons
P4022.M039
M39
5,00 tons 10,00 tons 5,00 tons 10,00 tons 7,00 tons
5,00 tons 10,50 tons 5,00 tons
P4022.M042
M42
6,00 tons 12,00 tons 6,00 tons 12,00 tons 8,40 tons
6,00 tons 12,60 tons 6,00 tons
P4022.M043
M42
6,00 tons 12,00 tons 6,00 tons 12,00 tons 8,40 tons
6,00 tons 12,60 tons 6,00 tons
P4022.M045
M45
6,00 tons 12,00 tons 6,00 tons 12,00 tons 8,40 tons
6,00 tons 12,60 tons 6,00 tons
P4022.I100 & P4023.I100
(UNC 1”-8)
6,000 lbs
12,000 lbs
6,000 lbs
12,000 lbs
8,400 lbs
6,000 lbs
12,600 lbs
6,000 lbs
P4022.I125 & P4023.I125
(UNC 1 1/4”-7)
7,500 lbs
15,000 lbs
7,500 lbs
15,000 lbs 10,500 lbs
7,500 lbs
15,750 lbs
7,500 lbs
15,000 lbs
7,500 lbs
15,000 lbs 10,500 lbs
7,500 lbs
15,750 lbs
7,500 lbs
P4022.I137 & P4023.I137
(UNC 1 3/8”-6)
7,500 lbs
P4022.I150
(UNC 1 1/2”-6)
11,000 lbs 22,000 lbs 11,000 lbs 22,000 lbs 15,400 lbs 11,000 lbs 23,100 lbs 11,000 lbs
752
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
Technical Information
Double Swivel Lifting Rings for Wire Rope
P4012 Male
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
Part no.
Thread
P4012.M008
M8
0,30 tons
0,60 tons
0,30 tons
0,60 tons
0,40 tons
0,30 tons
0,60 tons
0,30 tons
P4012.M010
M10
0,60 tons
1,20 tons
0,60 tons
1,20 tons
0,80 tons
0,60 tons
1,30 tons
0,60 tons
P4012.M012
M12
1,00 tons
2,00 tons
1,00 tons
2,00 tons
1,40 tons
1,00 tons
2,10 tons
1,00 tons
P4012.M014
M14
1,30 tons
2,60 tons
1,30 tons
2,60 tons
1,80 tons
1,30 tons
2,70 tons
1,30 tons
P4012.M016
M16
1,60 tons
3,20 tons
1,60 tons
3,20 tons
2,20 tons
1,60 tons
3,40 tons
1,60 tons
P4012.M018
M18
2,00 tons
4,00 tons
2,00 tons
4,00 tons
2,80 tons
2,00 tons
4,20 tons
2,00 tons
P4012.M020
M20
2,50 tons
5,00 tons
2,50 tons
5,00 tons
3,50 tons
2,50 tons
5,30 tons
2,50 tons
P4012.I031
(UNC 5/16”-18)
650 lbs
1,300 lbs
650 lbs
1,300 lbs
910 lbs
650 lbs
1,365 lbs
650 lbs
P4012.I037
(UNC 3/8”-16)
1,200 lbs
2,400 lbs
1,200 lbs
2,400 lbs
1,680 lbs
1,200 lbs
2,520 lbs
1,200 lbs
P4012.I050
(UNC 1/2”-13)
2,200 lbs
4,400 lbs
2,200 lbs
4,400 lbs
3,080 lbs
2,200 lbs
4,620 lbs
2,200 lbs
P4012.I063
(UNC 5/8”-11)
3,800 lbs
7,600 lbs
3,800 lbs
7,600 lbs
5,320 lbs
3,800 lbs
7,980 lbs
3,800 lbs
P4012.I075
(UNC 3/4”-10)
5,500 lbs
11,000 lbs
5,500 lbs
11,000 lbs
7,700 lbs
5,500 lbs
11,550 lbs
5,500 lbs
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
753
Lifting Bolts
Technical Information
Hook Double Swivel Lifting Rings
P4017 Male
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
Part no.
Thread
P4017.M008
M8
0,30 tons
0,60 tons
0,30 tons
0,60 tons
0,40 tons
0,30 tons
0,60 tons
0,30 tons
P4017.M010
M10
0,60 tons
1,20 tons
0,60 tons
1,20 tons
0,80 tons
0,60 tons
1,30 tons
0,60 tons
P4017.M012
M12
1,00 tons
2,00 tons
1,00 tons
2,00 tons
1,40 tons
1,00 tons
2,10 tons
1,00 tons
P4017.M014
M14
1,30 tons
2,60 tons
1,30 tons
2,60 tons
1,80 tons
1,30 tons
2,70 tons
1,30 tons
P4017.M016
M16
1,60 tons
3,20 tons
1,60 tons
3,20 tons
2,20 tons
1,60 tons
3,40 tons
1,60 tons
P4017.M018
M18
2,00 tons
4,00 tons
2,00 tons
4,00 tons
2,80 tons
2,00 tons
4,20 tons
2,00 tons
P4017.M020
M20
2,50 tons
5,00 tons
2,50 tons
5,00 tons
3,50 tons
2,50 tons
5,30 tons
2,50 tons
P4017.I031
(UNC 5/16”-18)
650 lbs
1,300 lbs
650 lbs
1,300 lbs
910 lbs
650 lbs
1,365 lbs
650 lbs
P4017.I038
(UNC 3/8”-16)
1,200 lbs
2,400 lbs
1,200 lbs
2,400 lbs
1,680 lbs
1,200 lbs
2,520 lbs
1,200 lbs
P4017.I050
(UNC 1/2”-13)
2,200 lbs
4,400 lbs
2,200 lbs
4,400 lbs
3,080 lbs
2,200 lbs
4,620 lbs
2,200 lbs
P4017.I063
(UNC 5/8”-11)
3,800 lbs
7,600 lbs
3,800 lbs
7,600 lbs
5,320 lbs
3,800 lbs
7,980 lbs
3,800 lbs
P4017.I075
(UNC 3/4”-10)
5,500 lbs
11,000 lbs
5,500 lbs
11,000 lbs
7,700 lbs
5,500 lbs
11,550 lbs
5,500 lbs
754
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
Technical Information
Triple Swivel Lifting Rings
P4015 Male
 max. = 60°
Lifting type
 max. = 60°
α
α
P
P
P
P
P
P
No. of rings
1
2
1
2
2
2
4
4
Lifting angle
0°
0°
90°
90°
45°
60°
45°
60°
Part no.
Thread
P4015.M008
M8
0,30 tons
0,60 tons
0,30 tons
0,60 tons
0,40 tons
0,30 tons
0,60 tons
0,30 tons
P4015.M010
M10
0,60 tons
1,20 tons
0,60 tons
1,20 tons
0,80 tons
0,60 tons
1,30 tons
0,60 tons
P4015.M012
M12
1,00 tons
2,00 tons
1,00 tons
2,00 tons
1,40 tons
1,00 tons
2,10 tons
1,00 tons
P4015.M014
M14
1,30 tons
2,60 tons
1,30 tons
2,60 tons
1,80 tons
1,30 tons
2,70 tons
1,30 tons
P4015.M016
M16
1,60 tons
3,20 tons
1,60 tons
3,20 tons
2,20 tons
1,60 tons
3,40 tons
1,60 tons
P4015.M018
M18
2,00 tons
4,00 tons
2,00 tons
4,00 tons
2,80 tons
2,00 tons
4,20 tons
2,00 tons
P4015.M020
M20
2,50 tons
5,00 tons
2,50 tons
5,00 tons
3,50 tons
2,50 tons
5,30 tons
2,50 tons
P4015.M022
M22
3,00 tons
6,00 tons
3,00 tons
6,00 tons
4,20 tons
3,00 tons
6,30 tons
3,00 tons
8,00 tons
4,00 tons
8,40 tons
4,00 tons
P4015.M024
M24
4,00 tons
8,00 tons
5,60 tons
4,00 tons
P4015.M027
M27
5,00 tons 10,00 tons 5,00 tons 10,00 tons
7,0 tons
5,00 tons 10,50 tons 5,00 tons
P4015.M030
M30
6,30 tons 12,60 tons 6,30 tons 12,60 tons 8,80 tons
6,30 tons 13,20 tons 6,30 tons
P4015.M036
M36
10,00 tons 20,00 tons 10,00 tons 20,00 tons 14,00 tons 10,00 tons 21,00 tons 10,00 tons
P4015.M042
M42
12,50 tons 25,00 tons 12,50 tons 25,00 tons 17,50 tons 12,50 tons 26,30 tons 12,50 tons
P4015.M048
M48
20,00 tons 40,00 tons 20,00 tons 40,00 tons 28,00 tons 20,00 tons 42,00 tons 20,00 tons
P4015.M056
M56
22,00 tons 44,00 tons 22,00 tons 44,00 tons 30,80 tons 22,00 tons 46,20 tons 22,00 tons
P4015.I031
(UNC 5/16”-18)
650 lbs
1,300 lbs
650 lbs
1,300 lbs
910 lbs
650 lbs
1,365 lbs
650 lbs
P4015.I037
(UNC 3/8”-16)
1,200 lbs
2,400 lbs
1,200 lbs
2,400 lbs
1,680 lbs
1,200 lbs
2,520 lbs
1,200 lbs
P4015.I050
(UNC 1/2”-13)
2,200 lbs
4,400 lbs
2,200 lbs
4,400 lbs
3,080 lbs
2,200 lbs
4,620 lbs
2,200 lbs
P4015.I063
(UNC 5/8”-11)
3,800 lbs
7,600 lbs
3,800 lbs
7,600 lbs
5,320 lbs
3,800 lbs
7,980 lbs
3,800 lbs
P4015.I075
(UNC 3/4”-10)
5,500 lbs
11,000 lbs
5,500 lbs
11,000 lbs
7,700 lbs
5,500 lbs
11,550 lbs
5,500 lbs
P4015.I088
(UNC 7/8”-9)
6,600 lbs
13,200 lbs
6,600 lbs
13,200 lbs
9,240 lbs
6,600 lbs
13,860 lbs
6,600 lbs
P4015.I100
(UNC 1”-8)
P4015.I125
(UNC 1 1/4”-7)
14,000 lbs 28,000 lbs 14,000 lbs 28,000 lbs 19,600 lbs 14,000 lbs 29,400 lbs 14,000 lbs
P4015.I150
(UNC 1 1/1”-6)
20,000 lbs 40,000 lbs 20,000 lbs 40,000 lbs 28,000 lbs 20,000 lbs 42,000 lbs 20,000 lbs
P4015.I200
(UNC 2”-4 1/2)
50,000 lbs 100,000 lbs 50,000 lbs 100,000 lbs 70,000 lbs 50,000 lbs 105,000 lbs 50,000 lbs
10,000 lbs 20,000 lbs 10,000 lbs 20,000 lbs 14,000 lbs 10,000 lbs 21,000 lbs 10,000 lbs
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
755
Steel Male Lifting Eye Bolts
w1
w2
w3
Lifting Bolts
F2
F1
45°
h
d1
P4040
l
d2
Material
Forged steel (C15E) annealed and zinc
plated. Contact face machined.
CE marked.
Hot dipped galvanised versions (for
more demanding applications and
limited outside use) also available on
request.
critical to ensure face is in firm contact
with the mating surface.
Inch versions also readily available as
standard.
Tips
Maximum load values are only
applicable when the thread is fully
screwed in place and the material it is
being used in is as least as strong as
Technical Notes
To DIN 580.
When installing lifting eye bolts it is
Order No.
P4040.060
P4040.080
P4040.100
P4040.120
P4040.140
P4040.160
P4040.180
P4040.200
P4040.220
P4040.240
P4040.270
P4040.300
P4040.330
P4040.360
P4040.390
P4040.420
P4040.450
P4040.480
P4040.520
P4040.560
P4040.640
P4040.720
P4040.800
P4040.999
the that of the bolt.
Values given are for steel and cast iron
components.
Important Notes
Not to be used at lift angles of greater
than 45° or with swivelling loads.
Thread
d1
l
h
w1
d2
w2
w3
F1 max.
Kg
F2 max.
Kg
X
Kg
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
M6
M8
M10
M12
M14
M16
M18
M20
M22
M24
M27
M30
M33
M36
M39
M42
M45
M48
M52
M56
M64
M72 x 6
M80 x 6
M100 x 6
13
13
17
20,5
20,5
27
27
30
30
36
36
45
45
54
54
63
63
68
68
78
90
100
112
130
36
36
45
53
53
62
62
71
71
90
90
109
109
128
128
147
147
168
168
187
208
260
298
330
36
36
45
54
54
63
63
72
72
90
90
108
108
126
126
144
144
166
166
184
206
260
296
330
20
20
25
30
30
35
35
40
40
50
50
65
65
75
75
85
85
100
100
110
120
150
170
190
20
20
25
30
30
35
35
40
40
50
50
60
60
70
70
80
80
90
90
100
110
140
160
180
8
8
10
12
12
14
14
16
16
20
20
24
24
28
28
32
32
38
38
42
48
60
68
75
70
140
230
340
500
700
930
1200
1500
1800
2500
3200
4200
4600
6000
6300
7800
8600
9900
11500
16000
20000
28000
40000
50
100
170
240
350
500
650
860
1050
1290
1830
2300
3050
3300
4400
4500
5500
6100
7100
8200
11000
14000
20000
29000
0,05
0,06
0,11
0,18
0,28
0,45
0,74
1,66
2,65
4,03
6,38
8,80
12,4
23,3
34,2
49,1
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
773
Lifting Bolts
Order No.
P4040.120-015
P4040.160-015
P4040.200-020
P4040.240-020
P4040.300-020
P4040.360-030
P4040.420-030
P4040.480-030
P4040.560-040
774
Thread
Fine
Fine
Fine
Fine
Fine
Fine
Fine
Fine
Fine
Steel Male Lifting Eye Bolts
d1
M12
M16
M20
M24
M30
M36
M42
M48
M56
x
x
x
x
x
x
x
x
x
1,5
1,5
2,0
2,0
2,0
3,0
3,0
3,0
4,0
l
h
w1
d2
w2
w3
F1 max.
Kg
F2 max.
Kg
X
Kg
20,5
27
30
36
45
54
63
68
78
53
62
71
90
109
128
147
168
187
54
63
72
90
108
126
144
166
184
30
35
40
50
65
75
85
100
110
30
35
40
50
60
70
80
90
100
12
14
16
20
24
28
32
38
42
340
700
1200
1800
3600
5100
7000
8600
11500
240
500
830
1270
2600
3700
5000
6100
8300
0,18
0,28
0,45
0,74
1,66
2,58
3,95
6,38
8,48
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Stainless Male Lifting Eye Bolts
w1
w2
w3
Lifting Bolts
F2
F1
45°
h
d1
P4043
l
d2
Material
Stainless steel (A4, AISI 316).
CE marked.
Inch versions also readily available as
standard.
the that of the bolt.
Values given are for steel and cast iron
components.
Technical Notes
To DIN 580.
When installing lifting eye bolts it is
critical to ensure face is in firm contact
with the mating surface.
Tips
Maximum load values are only
applicable when the thread is fully
screwed in place and the material it is
being used in is as least as strong as
Important Notes
Not to be used at lift angles of greater
than 45° or with swivelling loads.
Order No.
Material
d1
l
h
w1
d2
w2
w3
F1 max.
Kg
F2 max.
Kg
X
Kg
P4043.060-A4
P4043.080-A4
P4043.100-A4
P4043.120-A4
P4043.160-A4
P4043.200-A4
P4043.240-A4
P4043.300-A4
P4043.360-A4
P4043.420-A4
P4043.480-A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
s/s
s/s
s/s
s/s
s/s
s/s
s/s
s/s
s/s
s/s
s/s
M6
M8
M10
M12
M16
M20
M24
M30
M36
M42
M48
11
13
17
20,5
27
30
36
45
54
63
68
31
36
45
53
62
71
90
109
128
147
168
27
36
45
54
63
72
90
108
126
144
166
16
20
25
30
35
40
50
65
75
85
100
16
20
25
30
35
40
50
60
70
80
90
8
8
10
12
14
16
20
24
28
32
38
70
140
230
340
700
1200
1800
3200
4600
6300
8600
50
100
170
240
500
860
1290
2300
3300
4500
6100
0,05
0,06
0,11
0,18
0,28
0,45
0,74
1,66
2,65
4,03
6,38
P4043.060-A2
P4043.080-A2
P4043.100-A2
P4043.120-A2
P4043.160-A2
P4043.200-A2
P4043.240-A2
P4043.300-A2
A2 s/s
A2 s/s
A2 s/s
A2 s/s
A2 s/s
A2 s/s
A2s/s
A2 s/s
M6
M8
M10
M12
M16
M20
M24
M30
11
13
17
20,5
27
30
36
45
31
36
45
53
62
71
90
109
27
36
45
54
63
72
90
108
16
20
25
30
35
40
50
65
16
20
25
30
35
40
50
60
8
8
10
12
14
16
20
24
70
140
230
340
700
1200
1800
3200
50
100
170
240
500
860
1290
2300
0,05
0,06
0,11
0,18
0,28
0,45
0,74
1,66
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
777
High-tensile Male Lifting Eye Bolts
Lifting Bolts
steel
d3
h1
h2
d5
FB
FA
w1
d4
w2
r
h3
l1
P4054
l2
d1
d2
Material
High-tensile forged steel (42CrMo4V),
yellow galvanized. De-burred,
quenched, tempered and sand-blasted.
CE marked.
with the mating surface.
100% magnetic particle inspected.
These are extra strength lifting bolts,
which considerably exceed the
strength of standard lifting bolts.
screwed in place and the material it is
being used in is as least as strong as
the that of the bolt.
Values given are for steel and cast iron
components.
Technical Notes
When installing lifting eye bolts it is
critical to ensure face is in firm contact
Tips
Maximum load values are only
applicable when the thread is fully
Important Notes
Not to be used at lift angles of greater
than 90° or with swivelling loads.
Order No.
P4054.060
P4054.080
P4054.100
P4054.120
P4054.160
P4054.200
P4054.240
P4054.300
P4054.360
P4054.420
P4054.480
d1
l1
w1
h1
h2
h3
w2
l2
d2
d3
d4
d5
r
FA max.
tons
FB max.
tons
X
Kg
M6
M8
M10
M12
M16
M20
M24
M30
M36
M42
M48
13,0
13,0
17,0
20,5
27,0
30,0
36,0
45,0
54,0
63,0
68,0
7,0
7,0
9,3
10,6
12,4
14,5
17,6
21,1
24,7
28,1
33,4
38,3
38,3
45,8
56,4
66,0
75,7
95,8
116,0
136,3
156,5
178,7
22,0
22,0
27,5
33,0
36,4
44,0
55,0
66,0
77,0
88,0
99,0
8,5
8,5
5,0
11,0
13,0
16,0
20,0
25,0
30,0
35,0
40,0
6,8
8,9
11,3
13,6
15,4
16,6
21,6
25,1
28,7
34,1
41,4
2,5
2,5
3,0
3,5
4,0
5,0
6,0
7,0
8,0
9,0
10,0
20
20
25
30
35
40
50
65
75
85
100
36
36
40
54
64
72
90
108
126
144
166
20
20
25
30
35
40
50
60
70
80
90
6,0
6,0
7,7
9,4
13,0
16,4
19,6
25,0
30,3
35,6
41,0
4
4
4
6
6
8
12
15
18
20
22
0,76
0,76
0,94
1,50
3,80
5,70
7,50
11,30
15,00
22,60
30,00
0,19
0,19
0,24
0,38
0,95
1,50
1,90
2,90
3,80
5,70
7,50
0,06
0,06
0,11
0,18
0,28
0,45
0,74
1,66
2,65
4,03
6,83
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
779
Steel Female Lifting Eye Bolts
w1
w2
Lifting Bolts
F2
F1
w3
45°
h
d1
P4041
d2
Material
Forged steel (C15E), annealed and zinc
plated. Contact face machined.
CE marked
Hot dipped galvanised versions (for
more demanding applications and
limited outside use) also available on
request.
Order No.
P4041.060
P4041.080
P4041.100
P4041.120
P4041.140
P4041.160
P4041.180
P4041.200
P4041.200
P4041.240
P4041.270
P4041.300
P4041.330
P4041.360
P4041.390
P4041.420
P4041.480
P4041.560
P4041.640
P4041.720
P4041.800
P4041.999
P4041.120-015
P4041.160-015
P4041.200-020
P4041.240-020
Technical Notes
To DIN 582.
When installing lifting eye bolts it is
critical to ensure face is in firm contact
with the mating surface.
Inch versions also readily available as
standard.
Tips
Maximum load values are only
applicable when the thread and the
material it is being used in is as least
as strong as the that of the bolt.
Values given are for steel and cast iron
components.
Important Notes
Not to be used at lift angles of greater
than 45° or with swivelling loads.
Thread
d1
h
w1
d2
w2
w3
F1 max.
Kg
F2 max.
Kg
X
Kg
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
Coarse
M6
M8
M10
M12
M14
M16
M18
M20
M22
M24
M27
M30
M33
M36
M39
M42
M48
M56
M64
M72x6
M80x6
M100x6
36
36
45
53
62
62
71
71
71
90
90
109
109
128
128
147
168
187
208
260
298
330
36
36
45
54
63
63
72
72
72
90
90
108
108
126
126
144
166
184
206
260
296
330
20
20
25
30
35
35
40
40
40
50
50
65
65
75
75
85
100
110
120
150
170
190
20
20
25
30
35
35
40
40
40
50
50
60
60
70
70
80
90
100
110
140
160
180
8
8
10
12
14
14
16
16
16
20
20
24
24
28
28
32
38
42
48
60
68
75
70
140
230
340
500
700
930
1200
1500
1800
2500
3200
4200
4600
6000
6300
8600
11500
16000
20000
28000
40000
50
100
170
240
350
500
650
860
1050
1290
1830
2300
3050
3300
4400
4500
6100
8200
11000
14000
20000
29000
0,05
0,05
0,09
0,16
0,24
0,36
0,72
1,32
2,08
3,11
5,00
6,70
9,30
18,5
27,3
26,4
53
62
71
90
54
63
72
90
30
35
40
50
30
35
40
50
12
14
16
20
340
700
1200
1800
240
500
830
1270
0,18
0,28
0,45
0,74
Fine
Fine
Fine
Fine
M12
M16
M20
M24
x
x
x
x
1,5
1,5
2,0
2,0
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
775
Lifting Bolts
Order No.
P4041.300-020
P4041.360-030
P4041.420-030
P4041.480-030
P4041.560-040
776
Thread
Fine
Fine
Fine
Fine
Fine
Steel Female Lifting Eye Bolts
d1
M30
M36
M42
M48
M56
x
x
x
x
x
2,0
3,0
3,0
3,0
4,0
h
w1
d2
w2
w3
F1 max.
Kg
F2 max.
Kg
X
Kg
109
128
147
168
187
108
126
144
166
184
65
75
85
100
110
60
70
80
90
100
24
28
32
38
42
3600
5100
7000
8600
11500
2600
3700
5000
6100
8300
1,66
2,58
3,95
6,38
8,48
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
Stainless Female Lifting Eye Bolts
w1
w2
F2
F1
w3
45°
h
P4044
d1
d2
Material
Stainless steel (A4, AISI 316).
CE marked.
with the mating surface.
Inch versions also readily available as
standard.
as strong as the that of the bolt.
Values given are for steel and cast iron
components.
Technical Notes
To DIN 582.
When installing lifting eye bolts it is
critical to ensure face is in firm contact
Tips
Maximum load values are only
applicable when the thread and the
material it is being used in is as least
Important Notes
Not to be used at lift angles of greater
than 45° or with swivelling loads.
Order No.
Material
d1
h1
w1
d2
w2
h2
F1 max.
Kg
F2 max.
Kg
X
Kg
P4044.060-A4
P4044.080-A4
P4044.100-A4
P4044.120-A4
P4044.160-A4
P4044.200-A4
P4044.240-A4
P4044.300-A4
P4044.360-A4
P4044.420-A4
P4044.480-A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
A4
s/s
s/s
s/s
s/s
s/s
s/s
s/s
s/s
s/s
s/s
s/s
M6
M8
M10
M12
M16
M20
M24
M30
M36
M42
M48
31
36
45
53
62
71
90
109
128
147
168
27
36
45
54
63
72
90
108
126
144
166
16
20
25
30
35
40
50
65
75
85
100
16
20
25
30
35
40
50
60
70
80
90
8
8,5
10
11
13
16
20
22
25
30
38
70
140
230
340
700
1200
1800
3200
4600
6300
8600
50
100
170
240
500
860
1290
2300
3300
4500
6100
0,03
0,05
0,09
0,16
0,24
0,36
0,72
1,32
2,08
3,11
5,02
P4044.060-A2
P4044.080-A2
P4044.100-A2
P4044.120-A2
P4044.160-A2
P4044.200-A2
P4044.240-A2
A2
A2
A2
A2
A2
A2
A2
s/s
s/s
s/s
s/s
s/s
s/s
s/s
M6
M8
M10
M12
M16
M20
M24
31
36
45
53
62
71
90
27
36
45
54
63
72
90
16
20
25
30
35
40
50
16
20
25
30
35
40
50
8
8,5
10
11
13
16
20
70
140
230
340
700
1200
1800
50
100
170
240
500
860
1290
0,03
0,05
0,09
0,16
0,24
0,36
0,72
778
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
High-tensile Female Lifting Eye Bolts
steel
d3
d4
h1
h2
FB
FA
w1
w2
r
h3
P4055
d1
d2
Material
High-tensile forged steel (42CrMo4V),
yellow galvanized. De-burred,
quenched, tempered and sand-blasted.
CE marked.
with the mating surface.
100% magnetic particle inspected.
These are extra strength lifting bolts,
which considerably exceed the
strength of standard lifting bolts.
screwed in place and the material it is
being used in is as least as strong as
the that of the bolt.
Values given are for steel and cast iron
components.
Technical Notes
When installing lifting eye bolts it is
critical to ensure face is in firm contact
Tips
Maximum load values are only
applicable when the thread is fully
Important Notes
Not to be used at lift angles of greater
than 90° or with swivelling loads.
Order No.
P4055.060
P4055.080
P4055.100
P4055.120
P4055.160
P4055.200
P4055.240
P4055.300
P4055.360
P4055.420
P4055.480
780
d1
h1
w1
h2
h3
w2
d2
d3
d4
r
FA max.
tons
FB max.
tons
X
g
M6
M8
M10
M12
M16
M20
M24
M30
M36
M42
M48
38,3
38,3
45,8
56,4
66,0
75,7
95,8
116,0
136,3
156,5
178,7
7,0
7,0
9,3
10,6
12,4
14,5
17,6
21,1
24,7
28,1
33,4
22,0
22,0
27,5
33,0
36,4
44,0
55,0
66,0
77,0
88,0
99,0
8,5
8,5
5,0
11,0
13,0
16,0
20,0
25,0
30,0
35,0
40,0
6,8
8,9
11,3
13,6
15,4
16,6
21,6
25,1
28,7
34,1
41,4
20
20
25
30
35
40
50
65
75
85
100
36
36
40
54
64
72
90
108
126
144
166
20
20
25
30
35
40
50
60
70
80
90
4
4
4
6
6
8
12
15
18
20
22
0,76
0,76
0,94
1,50
3,80
5,70
7,50
11,30
15,00
22,60
30,00
0,19
0,19
0,24
0,38
0,95
1,50
1,90
2,90
3,80
5,70
7,50
0,05
0,05
0,09
0,16
0,24
0,36
0,72
1,32
2,08
3,11
5,02
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Lifting Bolts
Fall Arrest Swivel Rings
360°
h2
w2
w1
d
P4030
A/F
h1
Material
High tensile corrosion resistant steel,
strength class >8.
Coloured yellow to indicate personnel
safety.
Supplied with CE certificate.
of persons. The yellow colour indicates
the personnel safety use.
Tips
Marked with the number of persons
the ring is certified to support. For use
by personnel wearing safety
harnesses. Suitable for 1 or 2 persons
as marked.
Typically used in building maintenance,
wind power and offshore industries.
Technical Notes
Conforms to EN795:1996.
Single articulation, 360°.
Clearly marked with maximum number
Order No.
P4030.M012
P4030.M016
P4030.M020
772
Max.
no. of
persons
1
2
2
d
Important Notes
The thread diameter and depth must
be appropriate to the material into
which it will be installed:
Steel (min. ST37) - 1 x thread dia.
Cast iron - 1.25 x thread dia.
Aluminium - 2 x thread dia.
Other light metals - 2.5 x thread dia.
Tolerance of female thread to be 6H
(metric).
l
w1
h1
h2
w2
w3
A/F
Torque
to Nm
X
Kg
21
27
30
60
90
90
57
78
78
30
38
38
20
35
35
34
45
45
4
8
8
15
50
100
0,24
0,80
0,80
tol. 6g
M12x1,75
M16x2,00
M20x2,50
l
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
Quick Release Lifting Pins
Lifting Bolts
steel
l8
l4
d3
l2
l1
l3
l5
R1,5
d2 d1
l6 l7
P4074
Material
Pin & body: heat treaded steel,
tempered, manganese phosphate
treated.
Button: aluminium, red anodised.
Temperature range up to +250°C.
Easy installation with plain drilled hole
to H11 tolerance.
Tips
The design of the safety shackle
prevents accidental locking/unlocking.
Safety shackle is adjustable and can be
used to lift components at 90°, 45° or
180°.
Technical Notes
Pressing = unlocking. Releasing =
locking.
Max. loads up to 4.8kN (with a 5 fold
in-built safety factor).
Order No.
P4074.080-010
P4074.080-015
P4074.080-025
P4074.080-035
P4074.083-010
P4074.083-015
P4074.083-025
P4074.083-035
P4074.100-015
P4074.100-025
P4074.100-035
P4074.100-050
P4074.120-015
P4074.120-025
P4074.120-035
P4074.120-050
P4074.138--25
P4074.138-050
P4074.138-075
P4074.160-025
P4074.160-050
P4074.160-075
d1
8
8
8
8
8,3
8,3
8,3
8,3
10
10
10
10
12
12
12
12
13,8
13,8
13,8
16
16
16
l1
15
15
25
35
15
15
25
35
15
25
35
50
15
25
35
50
25
50
75
25
50
75
d2
9,35
9,35
9,35
9,35
9,65
9,65
9,65
9,65
11,7
11,7
11,7
11,7
14,20
14,20
14,20
14,20
16,20
16,20
16,20
18,60
18,60
18,60
Important Notes
F1*, F2* and F3* are values calculated
on a 5-fold safety factor.
When machining receiving hole in
aluminium we recommend use of
hardened bush or collar in receiving
hole.
Supplied with TUV test certificate of
manufacturing process. Parts not
individually tested.
d3
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
25,0
25,0
25,0
d4
min.
9,85
9,85
9,85
9,85
10,05
10,05
10,05
10,05
12,2
12,2
12,2
12,2
14,7
14,7
14,7
14,7
16,7
16,7
16,7
19,2
19,2
19,2
l2
8,75
8,75
8,75
8,75
8,75
8,75
8,75
8,75
10,2
10,2
10,2
10,2
11,0
11,0
11,0
11,0
13,0
13,0
13,0
15,1
15,1
15,1
Tel: 01483 26 67 76
Fax: 01483 26 67 75
l3
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
31,0
31,0
31,0
l4
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
44,5
44,5
44,5
l5
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
l6
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
l7
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
l8
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
92,8
92,8
92,8
92,8
92,8
92,8
x
x
min.
max.
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
5
10
15
15
5
10
15
15
10
15
25
35
10
20
25
45
15
35
35
20
40
55
For
hole
F1*
kN
X
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
2,7
2,7
2,7
2,7
3,5
3,5
3,5
3,5
3,8
3,8
3,8
4,8
4,8
4,8
218
220
223
226
218
220
223
226
226
238
244
252
238
243
251
268
251
279
309
312
353
388
g
H11
8,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
10
10
10
10
12
12
12
12
13,8
13,8
13,8
16
16
16
web: mechanicalcomponents.co.uk
a website from Automotion Components
781
Lifting Bolts
Quick Release Lifting Pins
stainless
l8
l4
d3
l2
l1
l3
l5
R1,5
d2 d1
l6 l7
P4075
Material
Pin: stainless steel (1.4542, AISI 630),
precipitation hardened, passivated.
Shackle: stainless steel (1.4571),
spring - stainless steel.
Button: aluminium, red anodised.
Easy installation with plain drilled hole
to H11 tolerance.
Corrosion and weather resistant,
therefore suitable for outdoor
applications.
Technical Notes
Pressing = unlocking. Releasing =
locking.
Max. loads up to 4.8kN (with a 5 fold
in-built safety factor).
Temperature range up to +250°C.
Tips
The design of the safety shackle
prevents accidental locking/unlocking.
Safety shackle is adjustable and can be
used to lift components at 90°, 45° or
180°.
Order No.
P4075.080-010
P4075.080-015
P4075.080-025
P4075.080-035
P4075.083-010
P4075.083-015
P4075.083-025
P4075.083-035
P4075.100-015
P4075.100-025
P4075.100-035
P4075.100-050
P4075.120-015
P4075.120-025
P4075.120-035
P4075.120-050
P4075.138-025
P4075.138-050
P4075.138-075
P4075.160-025
P4075.160-050
P4075.160-075
782
d1
8
8
8
8
8,3
8,3
8,3
8,3
10
10
10
10
12
12
12
12
13,8
13,8
13,8
16
16
16
l1
15
15
25
35
15
15
25
35
15
25
35
50
15
25
35
50
25
50
75
25
50
75
d2
9,35
9,35
9,35
9,35
9,65
9,65
9,65
9,65
11,7
11,7
11,7
11,7
14,2
14,2
14,2
14,2
16,20
16,20
16,20
18,6
18,6
18,6
d3
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
21,5
25,0
25,0
25,0
d4
min.
9,85
9,85
9,85
9,85
10,05
10,05
10,05
10,05
12,2
12,2
12,2
12,2
14,7
14,7
14,7
14,7
16,7
16,7
16,7
19,2
19,2
19,2
l2
8,75
8,75
8,75
8,75
8,75
8,75
8,75
8,75
10,2
10,2
10,2
10,2
11,0
11,0
11,0
11,0
13,0
13,0
13,0
15,1
15,1
15,1
l3
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
25,7
31,0
31,0
31,0
l4
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
36,0
44,5
44,5
44,5
l5
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
27
Tel: 01483 26 67 76
Fax: 01483 26 67 75
l6
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
Important Notes
F1*, F2* and F3* are values calculated
on a 5-fold safety factor.
When machining receiving hole in
aluminium we recommend use of
hardened bush or collar in receiving
hole.
Supplied with TUV test certificate of
manufacturing process. Parts not
individually tested.
l7
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
49
l8
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
87,5
92,8
92,8
92,8
92,8
92,8
92,8
x
x
min.
max.
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
5
10
15
15
5
10
15
15
10
15
25
35
10
20
25
45
15
35
35
20
40
55
For
hole
F1*
kN
X
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
2,7
2,7
2,7
2,7
3,5
3,5
3,5
3,5
3,8
3,8
3,8
4,8
4,8
4,8
218
220
223
226
218
220
223
226
233
243
250
257
246
255
265
276
251
279
309
325
367
403
g
H11
8,0
8,0
8,0
8,0
8,0
8,0
8,0
8,0
10
10
10
10
12
12
12
12
13,8
13,8
13,8
16
16
16
web: mechanicalcomponents.co.uk
a website from Automotion Components
Bushes
Lifting Bolts
for QR lifting pins
d1
d3
l3
l1
l2
A/F
d2
d
f1
45
P4077
x
f2
f3
x
l
x
Order No.
P4077.080-015
P4077.080-025
P4077.080-035
P4077.100-015
P4077.080-010
P4077.100-025
P4077.100-035
P4077.100-050
P4077.120-015
P4077.120-025
P4077.120-035
P4077.120-050
P4077.160-025
P4077.160-050
P4077.160-075
materials. Can be used in thin-walled
parts and in blind holes.
Technical Notes
Locating bushes are used for quick and
safe locating of lifting pins P4074 and
P4075.
Provides easy and safe assembly, and
can be incorporated into a variety of
Material
Stainless steel (1.4542, AISI 630),
precipitation-hardened, passivated.
Tips
Lifting forces F1 to F3, have a 5 fold inbuilt safety factor.
d1
l
d2
d3
d4
l1
l2
A/F
x*
f1
kN*
f2
kN*
f3
kN*
Tightening
torque
max. Nm
8
8
8
10
8
10
10
10
12
12
12
12
16
16
16
15
25
35
15
10
25
35
50
15
25
35
50
25
50
75
M16 x 1,5
M16
M16
M20 x 1,5
M16 x 1,5
M20 x 1,5
M20
M20
M24 x 1,5
M24 x 1,5
M24
M24
M30 x 2
M30
M30
24
24
24
28
24
28
28
28
32
32
32
32
39
39
39
9,8
9,8
9,8
12,2
9,8
12,2
12,2
12,2
14,7
14,7
14,7
14,7
19,2
19,2
19,2
27,5
37,5
47,5
35,5
27,5
35,5
46,0
65,0
35,5
36,5
48,5
72,5
44,0
66,0
96,0
20
25
35
24
20
24
29
49
24
24
36
60
29
44
74
19
19
19
24
19
24
24
24
27
27
27
27
30
30
30
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
2,7
1,5
2,7
2,7
2,7
3,5
3,5
3,5
3,5
4,8
4,8
4,8
1,2
1,2
1,2
2,4
1,2
2,4
2,4
2,4
3,2
3,2
3,2
3,2
4,5
4,5
4,5
0,5
0,5
0,5
2,1
0,5
2,1
2,1
2,1
2,8
2,8
2,8
2,8
4,1
4,1
4,1
90
75
75
145
90
145
130
130
220
220
200
200
440
400
400
Tel: 01483 26 67 76
Fax: 01483 26 67 75
web: mechanicalcomponents.co.uk
a website from Automotion Components
X
g
33
46
55
70
32
73
93
117
94
102
119
164
163
236
323
783