CLOCK INPUT CONFIGURATION
SETPOINT MODIFICATION
PRESS
Read carefully the safety guidelines and programming instructions
contained in this manual before using/connecting the device.
Disconnect power supply before proceeding to hardware settings or
electrical wirings.
TCT101-3ABC USER MANUAL
PIXSYS www.pixsys.net
e-mail: [email protected] - [email protected]
Software V 2.06
2300.10.139-RevH 060513
Only qualified personnel should be allowed to use the device and/or
service it and in accordance to technical data and environmental
conditions listed in this manual.
Do not dispose electric tools together with household waste materials in
observance of European Directive 2002/96/CE
WIRING DIAGRAM
PNP
NPN
INTRODUCTION
-
Techometer TCT101 allows to read the frequency (max 100KHz) of a signal
from single or double (bidirectional encoder) input.
2 universal digital inputs are available (NPN/PNP/Potential free contact) for
external commands like output activation or Hold/ Stop current visualization;
one input it is also analogue in order to allow setpoint modification by external
potentiometers.
+
OUT
Proximity
Sensor PNP
3 wires
Programming
Software
Power Supply
Selects chosen digit
3a
LOADING DEFAULT SETTINGS
PRESS
DISPLAY
3
1
1
1
2
OUT
Proximity
Sensor PNP
2 wires
1
Fase A
Fase Z
Fase B
POSITIVO
GND
POTENZIOMETRO 5..10 Kohm
Risoluzione 1000 punti
Encoder
Potentiometer:
To modify Set1 or Set2 by external potentiometer follow the steps below:
1- use potentiometers 5kOhm to 10kohm
PC ABS UL94V0 self-extinguishing
2- connect cursor to pin I3; a wrong connection may damage the potentiometer and
lead to lock of the device.
3PNP/NPN configurable as analogue for potentiometers. 3- accuracy on input is max 1000 points, therefore set the parameters "Upper limit"
(max 28 Vdc in PNP mode)
and "Lower limit" with a max difference of 1000 units.
(Ex.: LoS1 to 50,0 and uPS1 to 150,0 to modify time value related to Set1 between
2 relays 5A resistive charge
50 and 150 seconds with steps of one tenth). Greater differences would make
30mA(24Vac),40mA(24 Vdc),60mA (110...230Vac)
unstable the less significant digit.
.
4- To calibrate the scale of potentiometer enter the configuration mode and select:
Rechargeable battery, approx. 7days autonomy
Hin.3 as Pot Fin.3 as Set1 or Set2 P.tAr as Enable
Labsoftview 2.6 or later
Exit configuration mode and place potentiometer at minimum level and press key,
then place potentiometer at max level and press premere
key: the device
automatically exit the calibration procedure.
24...230Vac/Vdc +/-15% 50/60Hz / 2W
N.B.: A switch-off of the device would interrupt the calibration.
2
2
MEANING
3
3
3
There are two methods:
Report the activation of Q2
> With the device connected to the power supply
insert the memory card when the controller is off.
Report serial transmission by the TCT101
3
4
to confirm
(Only if the values stored on Mmeory Card are correct).
By pressing the
Confirm using the
Dima di foratura
28.5 x 70.5 mm
Frontal panel cut-out
Q1
Q2
5A 230V
Resistive
1/2HP
Spessore suggerito
2÷8 mm
Suggested thickness
> With the controller disconnected from the power supply:
Insert the memory card and press the programming button.
When writing the parameters, the LED turns red and on completing the procedure
it changes to green. It is possible to repeat the procedure.
5A 230V
Resistive
1/2HP
PIXSYS
TCT101-3ABC
MEMORY C.121
To update the memory card values, follow the procedure described in the first
method, setting display 2 to
so as not to load the parameters on controller.
PIXSYS
1
U1
CN1
6
C1
Memory Card (optional)
with battery
Cod. MEMORY C243
1
CN1
6
35 mm
The device loads the new data and starts again.
UPDATING MEMORY CARD.
TCT101
2
Enter configuration and change at least one parameter.
Exit configuration. Changes are saved automatically.
MAXIMUM AND MINIMUM PEAK FUNCTION
DISPLAY
PRESS
If enabled maximum peak function, maximum peak
value obtained is visualized.
1
2
3
3
77 mm
key .
The memory card is equipped with an internal battery with a life of about 1000
uses.
Memory Card (optional)
Cod. MEMORY C121
1
key display 2 shows
7
53 mm
and
If enabled minimum peak function, minimum peak
value obtained is visualized.
If enabled peak function, minimum and maximum peak
value will initialize to current timer value.
Enter password
+
Scroll parameters
pressing
or
and an arrow key
Default
Sampling frequency software filter
No software filter on reading
Mean realized on samplings done within time set
in this parameter. Display will be updated according to
this time range.
Default
Visualization time base
Visualized value referred to the second
Visualized value referred to the minute
Visualized value referred to the hour
Impulses on visualized unit
Number of impulses for single unit. For example,
in speed measurement, it indicates how many impulses
corresponds to a full revolution.
Default
1 pulse
...
9999 pulse
0
0.0
0.00
0.000
Default
Tachometer value visualization format
No decimal digit visualization
1 decimal digit visualization
2 decimal digits visualization
3 decimal digits visualization
Default
MEASURE UNIT CONFIGURATION
configuration table
or
99.99 pulse
...
0.01 pulse
P-18 Decimal Point
Display shows first parameter of
Increase or decrease value on display
5
DO
Modify blinking digit, pass to the
next one pressing
or
Enter the new data
that will be stored
when releasing the keys
P-19 Measure Unit 1
Setting digit 1 of displayed measuring unit
P-20 Measure Unit 2
Setting digit 2 of displayed measuring unit
P-21 Measure Unit 3
Setting digit 3 of displayed measuring unit
P-22 Measure Unit 4
Edit digits
Setting digit 4 of displayed measuring unit
Set each of 4 digits as chosen
Default ----
SETPOINT CONFIGURATION
End of configuration,
the device exits from programming mode.
6
P-23 Display Set 1
P-26 Display Set 2
Disable
Visualized
Modifiable
PARAMETERS LIST
CLOCK INPUT CONFIGURATION
P-01 Clock Input
I1
Encoder
Input signal on I1
Input signal on I1 and I2 (bidirectional encoder)
Default
P-02 Hardware input 1 Input 1 hardware configuration
P-05 Filtre Input 1
NPN (not available on input 3)
PNP
TTL
Potentiometer (available only for input 3)
P-06 Active State Input 2
Input 2 active state
P-07 Active State Input 3
Input 3 active state
High level
Low level
P-08 Function Input 2
Default
Disable
Min Peak
Max Peak
All Peak
Default 0
Set 1 maximum value (0...9999)
Default 999
P-28 Upper Limit Set 2
Set 2 maximum value(0...9999)
Default 999
Default
Function associated to key UP (up arrow)
Desabled
Max. registered peak visualization (reset by UP+DOWN key)
Default
Function associated to key DOWN (down arrow)
Desabled
Min. registered peak visualization (reset by UP+DOWN key)
Default
Default 0
Tachometer outputs always enabled
Outputs enabled automatically
Tachometer outputs enabled by digital inputs
P-30 Logic Output Mode1
Tachometer logic output mode 1
P-34 Logic Output Mode2
Tachometer logic output mode 2
High Deviation
Low Deviation
Inside Band
Out of Band
P-35 Activation Delay 2
P-32 Deactivation Delay 1
Active output with high deviation
Active output with low deviation
Active output inside band
Active output out of band
Default
Logic output 2 activation delay
Defines logic output activation delay.
Default
Setting range from 0.0 sec
to 999.9 sec.
Logic output 1 deactivation delay
Logic output 2 deactivation delay
Defines logic output deactivation delay.
Default
Setting range from 0.0 sec
to 999.9 sec.
Tachometer logic output 1 duration
P-37 Output 2 Duration
Tachometer logic output 2 duration
Automatic
Latch output (clear by FNC key)
Pulse 0.1 sec
to
Pulse 99.9 sec
Default
Logic output 1 activation delay
P-33 Output 1 Duration
Automatic output duration
Latch output, reset by FNC
0,1 sec output inpulse duration
Default
99,9 sec output inpulse duration
OUTPUT CONFIGURATION
P-39 Output Q2 Setup
Default
Outputs enabled
TACHOMETER LOGIC OUTPUT MODE CONFIGURATION
P-38 Output Q1 Setup
Power-off memory
No peak value stored at switch-off
Minimum peak value stored at switch-off
Maximum peak value stored at switch-off
Max. and Min. peak values stored at switch-off
Always enable
Automati enable
Enable by input
0.0 sec
to
999.9 sec
BACKUP MEMORY CONFIGURATION
P-13 Power-off Memory
Set 2 minimum value (0...9999)
P-25 Upper Limit Set 1
P-36 Deactivation Delay 2
Potentiometer calibration procedure
Desabled
Enabled
P-12 Function Key DOWN
Disable
Display min peak
P-27 Lower Limit Set 2
0.0 sec
to
999.9 sec
Set1 setting by potentiometer
Set2 setting by potentiometer
P-11 Function Key UP
Disable
Display max peak
Default Set1
Set 1 minimum value (0...9999)
P-31 Activation Delay 1
Default
Function associated to Input 3
Desabled
Enable / Desable tachometer outputs
Hold visualized tachometer value
P-10 Potentiom. Tarature
Disable
Enable
Default
Function associated to Input 2
P-09 Function Input 3
Disable
Out Enable/Disable
Hold (only for I3)
Set1 (only for I3)
Set2 (only for I3)
Default
Input 1 hardware filter configuration
Input hardware filter desabled
Input hardware filter enabled (22nF)
High Level
Low Level
Default Set2
P-24 Lower Limit Set 1
P-29 Output Enable
P-04 Hardware input 3 Input 3 hardware configuration
Off
On
Setpoint 2 display selection
Setpoint value not visualized
Setpoint value visualized
Setpoint value visualized and modifiable
OUTPUT ENABLE CONFIGURATION
P-03 Hardware input 2 Input 2 hardware configuration
NPN
PNP
TTL
Potent.
Setpoint 1 display selection
Input signal selection
INPUT CONFIGURATION
On activation display 1 shows and display 2 shows
SIZE AND INSTALLATION
42mm
inserimento
Memory Card
Switch the device off
and restart it
Display 1 shows
with 1st digit blinking, while
Display 2 shows
for 3 seconds
sec
min
hour
P-17 Pulse in Unit
The device loads
default settings
to confirm
Parameters and setpoint values can be copied from one device to
another using the Memory car.
Report the activation of Q1
Guarnizione per 32x74
Cod. 1600.00.082 (optional)
Gasket for 32x74
P-16 Timebase
Enter password
Modify blinking digit, pass to the
next digit pressing
or
For lower frequency values 0 is visualized on display.
This parameter forces max. refresh time of display
from 100 to 0.1 sec.
DISPLAY CONFIGURATION
DO
Display 1 shows
with 1st digit blinking, while
Display 2 shows
for 3 seconds
MEMORY CARD (optional)
LED
P-15 Software Filter
off
0.01 sec
...
1.00 sec
Modifies blinking digit
of selected SET
or
2
Operating Operating temperature 0-40°C, humidity 35..95uR%
temperature
Sealing Front panel IP65 (with optional gasket) ,
Box IP30, Terminal blocks IP20
Back-UP
2a
CONFIGURATION PARAMETER MODIFICATION
PRESS
DISPLAY
TECHNICAL DATA
Outputs
OUT 24V
Modifies selected SET
NPN
Thanks for choosing a Pixsys device.
Digital
Inputs
or
2
PNP
0.01 Hz
...
0.09Hz
0.1 Hz
...
10.0Hz
Visualizes SETPOINT 1 / 2
2
1
*2300.10.139-F*
Material
1
P-14 Minimum Input FrequencyLower frequency visualized
DISPLAY
Disable
Logic Out 1 n.o.
Logic Out 1 n.c.
Logic Out 2 n.o.
Logic Out 2 n.c.
Relay Q1 output setting
Relay Q2 output setting
Desabled output
Logic output 1 on n.o. contact
Logic output 1 on n.c. contact
Logic output 2 on n.o. contact
Logic output 2 on n.c. contact
Default 2
Default 1
TCT101-3ABC “TACHOMETER”
CLOCK INPUT CONFIGURATION
P-01
Clock
Input
0.01 Hz
to
10,0 Hz
P-15
Software
Filtre
P-17
Pulses
in Unit
P-16
Timebase
off
0.01 sec
...
1.00 sec
sec
min
hour
INPUT
CONFIGURATION
P-05
Filter
Input 1
P-02
Hardware
Input 1
P-23
Display
Set 1
Off
On
P-03
Hardware
Input 2
P-08
Function
Input 2
High Level
Low Level
Disable
Out Enable/Disable
P-09
Function
Input 3
P-26
Display
Set 2
Disable
Out Enable/Disable
Hold Display Value
Set1
Set2
High Level
Low Level
P-10
Potentiometer
tarature
P-11
Function
Key UP
Disable
Enable
Set2
P-12
Function
Key DOWN
Key
P-30
Logic Output
Mode 1
Disable
Display min peak
BACKUP MEMORY
CONFIGURATION
P-13
Power-off
Memory
PNP
input
TTL
input
Logic
level
H
< 4,7 v
> 5,7 v (I1, I2)
>12,4 v (I3)
>2,5 v
L
> 5,7 v
< 4,7 v (I1, I2)
< 10,2 v (I3)
< 2,0 v
Disable
Max Peak
Min Peak
All Peak
0.0 sec
...
999.9 sec
ERROR IN READING OF EEPROM MEMORY (NotE 1)
P-32
Deactivation
Delay 1
0.0 sec
...
999.9 sec
INCORRECT STATUS DATA (NotE 1)
P-33
Output 1
Duration
P-22
Measure
Unit 4
edit digit 3
Always enable
TACHOMETER OUTPUTS ARE ALWAYS ENABLED.
Automatic enable
DEPENDING ON LOGIC OUTPUT MODE PARAMETER, THERE ARE DIFFERENT OPERATING MODES:
- High Deviation : OUTPUTS ARE ALWAYS ENABLED
- Low Deviation : AT STARTING, OUTPUTS ARE DESABLED; THEY CAN BE ENABLED WHEN TACHOMETER VALUE OVERCOMES
SETPOINT VALUE AND KEPT ENABLED UNTIL INPUT SIGNAL FALLS BELOW VALUE SET ON PARAMETER «MINIMUM INPUT
FREQUENCY» (P-14);
- Inside Band : OUTPUTS ARE ALAWAYS ENABLED
- Out of Band : AT STARTING OUTPUTS ARE DESABLED, THEY CAN BE ENABLED WHEN TACHOMETER VALUE OVERCOMES
SET1-SET2 VALUE, AND KEPT UTNITL INPUT SIGNAL FREQUENCY FALLS BELOW VALUE SET ON PARAMETER «MINIMUM INPUT
FREQUENCY» (P-14);
Enable by input
TACHOMETER OUTPUTS ARE ENABLED TO OPERATE ONLY IF:
- INPUT 2 FUNCTION IS SET ON OUT ENABLE/DISABLE AND INPUT
IS ACTIVE
- INPUT 3 FUNCTION IS SET ON Out Enable/Disable AND INPUT
IS ACTIVE
Logic
Out
SET
Tach.
Value
Activation
delay
P-34
Logic Output
Mode 2
Time
0
Auto 1
Clear by FNC Key
P-35
Activation
Delay 2
Pulse duration time
0
Tach. Value
Q2
Tach.
Value
Tach. Value
Activation delay
Deactivation delay
Output duration
Set
Logic
Out
SET
Activation
delay
Deactivation
delay
Time
Logic output
0
Auto 1
Clear by FNC Key
0
Pulse 1
Tach. Value
Activation delay
Deactivation delay
Output duration
Set1
Set2
Tach.
Value
SET2
Logic
Out
SET2
Tach. Value
SET1
Activation
delay
Activation
delay
Deactivation
delay
Deactivation
delay
Time
Logic output
0
Auto 1
Clear by FNC Key
Clear by FNC Key
0
Latch 1
Pulse duration time
P-36
Deactivation
Delay 2
0.0 sec
...
999.9 sec
P-37
Output 2
Duration
Automatic
Latch output (clear only by FNC key)
Pulse 0.1 (sec)
to
Pulse 99.9 (sec)
n.o.
n.c.
n.o.
n.c.
Pulse 1
Pulse duration time
0
Pulse 1
Tach. Value
0.0 sec
...
999.9 sec
1
1
2
2
P-39
Output Q2 (relay)
Setup
0
Latch 1
Output
duration
mode
High Deviation
Low Deviation
P-38
Output Q1 (relay)
Setup
Disable
Logic Out
Logic Out
Logic Out
Logic Out
Pulse duration time
TACHOMETER LOGIC OUTPUT MODE CONFIGURATION
OUTPUT RELAIS
CONFIGURATION
Q1
Deactivation
delay
0
Automatic
Latch output (clear only by FNC key)
Pulse 0.1 (sec)
to.
Pulse 99.9 (sec)
edit digit 4
3
Latch 1
INCORRECT BACKUP REGISTERS (NotE 2)
NotE 1: SWITCH THE DEVICE OFF AND RESTART IT; IF ERROR IS
STILL NOTIFIED, CONTACT TECHNICAL SERVICE.
NotE 2: DISCHARGED BATTERY. KEEP THE DEVICE CONNECTED
TO THE POWER SUPPLY IN ORDER TO RECHARGE THE
BATTERY.
edit digit 2
Tach.
Value
Activation delay
Deactivation delay
Output duration
Set
Output
duration
mode
INCORRECT PARAMETERS (NotE 1)
INCORRECT CALIBRATION DATA (NotE 1)
P-21
Measure
Unit 3
Logic output
TABLE OF ERROR MESSAGES
ERROR IN WRITING OF EEPROM MEMORY (NotE 1)
Tach. Value
Output
duration
mode
POWER-ON
RESET
NPN
input
Out Enable
High Deviation
Low Deviation
Inside Band (Band defined by SET2)
Out of Band (Band defined by SET2)
P-31
Activation
Delay 1
Disable
Display max peak
Type of
input
P-29
Output
Enable
2
P-28
Upper limit
Set 2
TACHOMETER LOGIC OUTPUT MODE CONFIGURATION
I3
Key
1
OUTPUT ENABLE
CONFIGURATION
Always enable
Automatic enable
Enable by Input
P-25
Upper limit
Set 1
Disable
P-27
Visualized Lower
limit
Modifiable
Set 2
P-07
Active State
Input 3
PNP
TTL
Potent.
0
0.0
0.00
0.000
Disable
P-24
Visualized Lower
limit
Modifiable
Set 1
I2
P-04
Hardware
Input 3
99.99
to
0.01
1
to
9999
P-20
Measure
Unit 2
edit digit 1
Set1
P-06
Active State
Input 2
NPN
PNP
TTL
P-18
Decimal
Point
SETPOINT CONFIGURATION
I1
NPN
PNP
TTL
P-19
Measure
Unit 1
DISPLAY CONFIGURATION
P-14
Minimum Input
Frequency
I1
Encoder
MEASURE UNIT CONFIGURATION
Activation delay
Deactivation delay
Output duration
Set1
Set2
Tach.
Value
SET2
SET2
Tach. Value
SET1
Activation
delay
Deactivation
delay
Deactivation
delay
Activation
delay
Time
Logic output
Output
duration
mode
0
Auto 1
Clear by FNC Key
Clear by FNC Key
0
Latch 1
Pulse duration time
0
Pulse 1
Pulse duration time
Logic
Out
Disable
Logic Out
Logic Out
Logic Out
Logic Out
1
1
2
2
n.o.
n.c.
n.o.
n.c.