LIGHT OPERATION
OPTIMISED MODE SELECTION (OMS)
FUEL GAUGE FUNCTION
SMART PORT TECHNOLOGY PLUS (SPT+)
HELMET MOUNTING
Located on the back of the light unit is the Function Button.
This operates the light and informs you of the mode and the
battery power status.
When light is off press and hold the Function Button. After 3
seconds multiple flashes indicate SPT+ is activated, keep
holding the function button OMS will now begin and the button
will flash in sequence.
After 3 seconds the function button becomes the fuel gauge.
The colour of the button now indicates the approximate
percentage of battery power left.
The Smart Port Technology+ not only enables the user to charge
the light but also to power accessories and ancillary products.
The highly acclaimed helmet bracket uses a ball joint,
to infinitely adjust the position of your light. Follow these
instructions to set up and position the light for riding.
The clamp is made up of three parts: Lower clamp disc, upper
clamp with ball joint socket and a nylon clamp bolt.
· To turn on the light, double click the Function Button, the
light turns on in the brightest mode.
· To switch between the constant settings, press the
Function Button once. When the setting is changed the
colour of the button for the first 3 seconds informs you
which lighting mode has been selected. Thereafter the
colour of the button is your fuel gauge indicating battery
power remaining.
· To activate the flashing or SOS mode, press and hold
the Function Button, release immediately after one flash.
The flashing or SOS mode can be activated from any of
the constant modes. To return to the high mode, press the
Function Button once.
· To turn off the light, press and hold the Function Button.
The light will briefly go out, then flash twice. Then release
the button and the light will have switched off.
The number of lit flashes denotes the program selected.
Release button when required program is reached.
DIABLO
AXIS
· To switch the Smart Port off - simply turn the light on
and off again.
JOYSTICK
When the battery has only 5% charge remaining in whichever
mode, the light will automatically switch to the low setting and
the function button will flash red. Light output will slowly dim
over the next hour and this is the extended burn time on reserve
power. Due to the high power of the Diablo the reserve mode
will not happen. Mode and Fuel Gauge functions will operate as
normal when using a remote switch. When using a support cell
battery the function button will only flash green to indicate the
light is charging.
RE-CHARGING INSTRUCTIONS
TAP (TAP ACTIVATED POWER) - DIABLO / AXIS ONLY
1. Ensure the light unit and SPT+ are turned off.
New for 2015 the Diablo and Axis gain improved functionality with
TAP. A simple tap to the light or helmet when helmet mounted will
change the mode to allow maximum speed and confidence on the
trails. TAP can be activated and deactivated as required along with
altering sensitivity.
2. Plug the Smart Charger into the power supply and switch on the
supply. The LED on the charger will show green (operational).
To change any TAP settings access program 9 via OMS, then
follow details as described below.
When you release the Function Button it will go green for two
seconds. While it is lit tap the light to select a setting. To turn TAP
on in its most sensitive setting tap the light once, two taps will select
medium sensitivity and 3 taps will select the least sensitive setting.
To turn TAP off, access program 9 and do not tap the light.
Joystick_Diablo_Axis_2015_QS_Guide.indd 1-3
· To activate SPT+ without the front light on, press and
hold the function button, immediately release when
the main light rapid flashes. Accessories and ancillary
products will now be powered.
3. Open the storm cap on the charge port then insert the charger
jack. The charger’s LED will show red when the light unit is
charging.
The Function Button will flash green when charging and show a
constant green when charged.
From empty the light unit will rapid charge till approx 95% at this
point the LED on the charger will go from red to green, and trickle
charge to 100%. Charging with USB could take an additional hour.
SPT+ automatically becomes active when the main light is
switched on. It also automatically shuts down when the light is
turned off.
HANDLEBAR MOUNTING
· Put the shorter plastic bolt through the lower clamp disc
and align with a selected vent on the inside of your helmet.
· Place the upper clamp through the top of the vent to meet
the bolt.
· Tighten the bolt. Take care not to damage your helmet.
WARNING: Ensure that the Smart Port is switched off
before charging.
· Use the shorter bolt first and if it is not long enough then
go to the longer bolt. Do not use the long bolt on thinner
section helmets, as this will stop the ball joint working or
possibly pop it out.
INTELLIGENT THERMAL MANAGEMENT (ITM)
· Clip the light body into the top part of the clamp.
Exposure Lights patented technology combats loss in efficiency
of LEDs at elevated temperatures. The technology maintains
optimum output for maximum efficiency.
· The light can be adjusted by rotating the ball joint when
holding the light and is easy to do when you are riding to
get the best position.
Exposure Lights have undertaken extensive research into the
effect of temperature on LED output. There is an optimum
temperature where the balance between light output and
battery burntime peaks, beyond this LEDs becomes inefficient.
The intelligent circuitry of ITM monitors the temperature of the
LEDs and adjusts power accordingly to ensure the LEDs remain
at the optimum efficient. The adjustment of the power doesn’t
noticeably drop the light output, it only maximises burntime.
The combination of ITM and new improved body designs for
increased heat dissipation ensures that no power is wasted,
maximising burn time.
· For added security attach the lanyard to the light and loop
the lanyard through a vent in your helmet.
· Attach the non-tab end of the silicone band to the short
arm of the bracket. Although universal this is the preferred
fitting option.
· Place the bracket onto your handlebar making sure the
short side of the bracket faces forward.
· Pull the tab under the handlebar and attach to the long
arm of the bracket.
· Simply click the light into the bracket making sure all is secure.
WARNING - Make sure that brake and gear cables cannot
catch on or interfere with the light or the bracket.
LANYARD FITTING
Exposure Lights recommend the use of the lanyard provided.
Looping it around helmet vents or handlebars could stop you
losing the light in the event of a crash.
example image
Helmet
Helmet
example image
14/08/2014 11:35
QUICKSTART GUIDE READY, SET UP, RIDE
MAINTENANCE
ACCESSORIES
Inspect and test your light before every ride.
·· RedEye
·· Support cell
Keep your Exposure light clean, and the lenses free of dirt.
The lenses are made of hi-tech resistant resin but can be
scratched. Be careful when cleaning any mud or dirt from
the lens. Never use a high pressure spray or hose on your
Exposure light. Do not use harsh abrasive or corrosive
materials to clean your Exposure light.
·· RedEye Micro
·· USB Boost Cable
·· RedEye Helmet
·· Car Charger
·· Remote Switch
·· Beacon
·· WhiteEye
·· Magni Grip
·· Head Band
Follow all charging instructions. If the unit is being stored
for long periods, please ensure the battery is periodically
charged fully. We suggest once every month. The same
applies to support cell batteries.
WARNING
Exposure Lights are very powerful lighting systems. Always
take care when operating. Do not look directly into the
light. This may cause serious injury. Do not shine directly
at others.
Exposure Lights / Ultimate Sports Engineering Ltd. accept
no liability for any injuries or other damages arising from
the use of their product in any circumstances.
We design them. We make them. We are here to help.
If you are experiencing any problems with your Exposure
Light or accessories please contact us directly at:
Service: +44 (0)1798 839300
EXPOSURE LIGHTS
[email protected]
Alternatively contact your Exposure Dealer/Distributor check
web for details www.exposurelights.com
Joystick_Diablo_Axis_2015_QS_Guide.indd 4-6
DIABLO MK6 • AXIS MK2 • JOYSTICK MK9
14/08/2014 11:35