INSTRUCTION MANUAL
LASER DISTANCE FINDER/
MEASURING TOOL
057-4585-0
If any parts are missing
or damaged, or if you have any
questions, please call
our toll-free helpline at
1-800-689-9928.
Read and understand this instruction manual
thoroughly before using the product. It contains
important information for your safety as well
as operating and maintenance advice.
Keep this instruction manual for future use.
Should this product be passed on to a third
party, then this instruction manual must be
included.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
TECHNICAL SPECIFICATIONS 3–4
SAFETY GUIDELINES 5–7
DESCRIPTION8
OPERATING INSTRUCTIONS 9–18
MAINTENANCE 19
TROUBLESHOOTING 20
PARTS LIST 21–22
WARRANTY 23–24
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
TABLE OF CONTENTS
2
TECHNICAL SPECIFICATIONS
RECOMMENDED USE
Indoors
STORAGE TEMPERATURE
-20 ºC to 60ºC (-4 to 140°F)
POWER SUPPLY
6V
(4 x 1.5 V AAA
alkaline batteries)
SIZE
113 x 56.4 x 35 (mm)
TYPICAL MEASURING RANGE 0.1–50 m*
TYPICAL MEASURING
ACCURACY
±3 mm*
WEIGHT (WITHOUT BATTERIES) 0.34 lb. (155 g)
*Important: Under unfavorable conditions, such as in bright sunlight or when measuring poorly
reflecting or very rough surfaces, the tool’s measuring range and accuracy will be reduced. In
such circumstances, please use a reflector (available separately) when taking measurements.
The reflector is a target to be used with the Laser Distance Finder/Measuring Tool to increase
the intensity of the reflected light.
SMALLEST UNIT DISPLAYED 1mm
LASER CLASS
II
LASER TYPE
λ=635 nm, P≤ 1 mW
AUTOMATIC SWITCH OFF
Laser: 20 seconds
Measuring tool: 5 minutes
ESTIMATED BATTERY LIFE Up to 5,000 single
(ALKALINE AAA BATTERIES) measurements
OPTIMUM OPERATING TEMPERATURE
-10 ºC to 50ºC (14° to 122°F)
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
TECHNICAL SPECIFICATIONS
4
3
SAFETY GUIDELINES
WARNING!
CAUTION!
Safety symbols in this Instruction Manual are used to flag possible dangers. The
safety symbols and their explanations require your full understanding. The safety
warnings do not, by themselves, eliminate any danger, nor are they substitutes for
proper accident prevention measures.
Do not attempt to modify the performance of the laser device in any way. This may
result in a dangerous exposure to laser radiation.
WARNING!
This Safety Alert Symbol indicates caution, warning, or danger. Failure to obey a
safety warning can result in serious injury to yourself or others. To reduce the risk of
injury, fire, or electric shock, always follow the safety precautions.
Become familiar with the Laser distance finder/measuring tool
Before using this Laser Distance Finder/Measuring Tool, read this Instruction Manual carefully.
Keep this Manual in a safe place for future reference.
Important
This device should only be serviced by a qualified service technician. For more information, call
the toll-free helpline at 1-800-689-9928.
Read all instructions thoroughly
Save these instructions
CAUTION!
Do not attempt to use this laser distance finder/measuring tool until you have
read all instructions, safety rules, and warnings carefully and thoroughly. Keep this
Instruction Manual and review it frequently for reference.
WARNING!
Be sure to read and understand all instructions in this manual before using this
product. Failure to follow all instructions may result in hazardous radiation exposure.
WARNING!
Laser radiation. Do not stare into the beam. Turn the laser beam on only when
using this tool.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
WARNING!
Use of controls, adjustments, or the performance of procedures other than those
specified in this manual may result in hazardous radiation exposure.
WARNING!
The use of optical instruments, such as, but not limited to, telescopes or transits to
view the laser beam will increase eye hazard.
This laser distance finder/measuring tool has a built-in laser light. The laser is a Class II and emits
output power of a maximum 1 mW and 620-690 nm wavelengths. These lasers do not normally
present an optical hazard. However, do not stare at the beam, as this can cause flash blindness.
The following label is on your laser distance finder/
LASER DISTANCE
057-4585-0
FINDER / MEASURING TOOL
measuring tool. It indicates the location from which
OUTIL À MESURER – TÉLÉMÈTRE À LASER
the laser distance finder/measuring tool emits
6V
4×1.5 V AAA Battery / 6V
4 piles AAA de 1,5V
the laser light. Be aware of the laser light location
ATTENTION
CAUTION
LASER RADIATION
RAYONNEMENT LASER : NE REGARDEZ
when using the tool. Always make sure that any by
DO NOT STARE INTO BEAM
PAS DIRECTEMENT LE FAISCEAU.
635nm, P≤1mW
635nm, Puissance≤1mW
standers in the vicinity of use are made aware of the
Class II laser product
Produit laser de classe II
Complies with 21 CFR parts Conforme au règlement 21 CFR
1040.10 and 1040.11
sections 1040.10 et 1040.11
dangers of looking directly into the laser.
MADE IN CHINA/FABRIQUÉ EN CHINE IMPORTED BY/IMPORTÉ PAR MASTERCRAFT CANADA
TORONTO, CANADA M4S 2B8
DATE CODE: CODE DE DATE :
• Do not remove or deface any product labels.
• Avoid direct eye exposure. The laser beam can
cause flash blindness.
• The laser tool is not a toy. Always keep it out of the reach of children. The laser light emitted
from this device should never be directed toward any person for any reason.
• Do not operate the tool around children or allow children to operate the tool.
• Do not place the tool in a position that may cause anyone to stare at the laser beam, whether
intentionally or unintentionally.
• Do not use on surfaces such as sheet steel that have shiny, reflective surfaces. The reflective
surface could reflect the beam back at the operator.
• Always turn the laser tool off when not in use. Leaving the tool on increases the risk of
someone inadvertently staring into the laser beam.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
SAFETY GUIDELINES
6
5
8
• Do not attempt to modify the performance of this laser device in any way. This may result in
a dangerous exposure to laser radiation.
• Do not attempt to repair or disassemble the laser distance finder/measuring tool. If
unqualified persons attempt to repair this product, serious injury may occur. Any repair
required on this laser product should be performed only by qualified service personnel.
• Do not operate the tool in combustible areas, such as in the presence of flammable liquids,
gases, or dust.
• Use of other accessories that have been designed for use with other laser tools could result
in serious injury.
• Keep batteries out of reach of children.
• Do not direct the laser distance finder/measuring tool towards the sun or other sources of
bright light. This may cause an Error reading or inaccurate measurements.
• Do not use the laser distance finder/measuring tool as a leveling tool.
• Do not operate the laser tool in wet, dusty, sandy, or other adverse environments. Such
conditions may damage inner components and affect measuring accuracy.
• When the laser distance finder/measuring tool is brought into a warm environment from very
cold conditions, or vice versa, allow it to come to the surrounding temperature before use.
• Measuring errors can occur when measuring toward colorless liquids (e.g., water), clean
glass, Styrofoam, or similar translucent or low-density materials.
• High-gloss surfaces will deflect the laser beam and result in Error measurements.
• Very bright surroundings combined with a very low reflecting surface will reduce the
measuring range and accuracy.
• Do not immerse the tool in water. Wipe off dirt with a damp, soft cloth. Do not use aggressive
cleaning agents or solutions. Treat the optical surfaces with the same care that you would
apply to eye glasses or cameras.
• The accuracy of the tool must be checked before use after it has been dropped or subjected
to other mechanical stresses.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
Know your laser distance finder/measuring tool
5
1
4
2
3
6
7
No.Description
No.Description
1
5
LCD display
Battery compartment
2Keyboard
6Laser-receiving lens
3
Positioning pin
7
4
1/4" tripod screw
Laser-exit aperture
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
DESCRIPTION
SAFETY GUIDELINES
7
10
Become familiar with the laser distance finder/measuring tool.
Before attempting to use this laser distance finder/measuring tool, become familiar with all of
its operating features and safety requirements.
LCD display
Large LCD screen with white backlighting helps makes it easy to read the large numeral
measuring data clearly, even in dark conditions.
Full battery indicator
Empty battery indicator
Indicates that the measurement is taken from the positioning pin
Indicates that the measurement is taken from the bottom of the tool
Indicates that the measurement is taken from the position of the tripod screw
Indicates that the measurement is taken from the front of the tool
Laser beam indicator
Single-distance measurement
Area measurement
Volume measurement
Single Pythagorean Theorem measurement
Keyboard function (fig 1)
fig 1
For operation, please see the references
to the specific functions and computations
later in this manual.
3
2
1
1.Power key - Turns on/off the tool.
2.Measure key - Turns on the laser and
5
4
takes measurements; activates the
6
continuous measurement.
8
7
3.Clear key - Clears the measurements;
reverts to single-distance measurement
mode.
4.Mode key - Changes the measuring mode among: area, volume, single Pythagorean Theorem,
double Pythagorean Theorem, and single-distance measurement modes.
5.Plus/Minus key - For addition or subtraction of measurements.
6.Measuring reference point - Switches the measuring reference among: the rear of the tool,
the position of the tripod screw, the front of the tool, and the positioning pin.
7.Unit conversion key
8.Max/Min key - Activates the maximum or minimum measuring mode.
To install batteries (fig 2)
This laser distance finder/measuring tool
uses four “AAA” batteries.
1.Push the hook to open the battery cover.
2.Insert four new “AAA” alkaline batteries
according to the polarity indicators in the
battery compartment. Be sure the polarity
(+/-) is correct!
3.Close the cover and lock it securely in place.
fig 2
Double Pythagorean Theorem measurement
Minimum measurement indicator
Maximum measurement indicator
Continuous measurement indicator
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
9
12
NOTE:
• Replace the batteries when the battery indicator shows empty.
• Remove the batteries from the laser distance finder/measuring tool when not using it for
extended periods.
• The 4 AAA batteries should match each other in brand and type.
• Do not mix old and new batteries. Do not mix alkaline, standard (Carbon-Zinc), or
rechargeable batteries.
• Remove dead batteries immediately and dispose of them according to your local ordinance.
Never dispose of batteries in fire.
To change the units
key to change the units among the choices listed below.
Press the
DISTANCE
AREA
0.000 m
0.000 m
0.000 m3
0 mm
0.000 m
0.000 m3
0.000 ft
0.000 ft
0.000 ft3
Turning the laser distance finder/measuring tool on and off
0' 00"
2
0.000 ft
0.000 ft3
to turn on the tool.
0.0 In
0.000 ft2
0.000 ft3
0 In 1/16
0.000 ft2
0.000 ft3
1.Press the power key
2.The tool will automatically self-calibrate. During this process, the laser will turn on briefly.
WARNING!
Do not point the laser dot at persons or animals and do not stare into the laser beam
or view it directly with optical instruments.
3.The tool will default to the single-distance measuring mode, indicating that the tool is ready
to take measurements.
for about 2 seconds to turn off the tool.
4.Press the power key
5.When the laser distance finder/measuring tool is inactive for 5 minutes, it will automatically
turn off to save battery power.
To change measuring reference point
The default reference setting is from the rear of the tool. Press the measuring reference point
. Each time the key is pressed, the reference point will change: the rear of the tool,
key
the position of the tripod screw, the front of the tool or the positioning pin location; the next
measurement will be taken from the position you set.
After powering off, the reference point will automatically default back to rear of the tool.
Clear function
Push the clear key
to erase the current measurement and display the previous
measurement.
While making area, volume or indirect measurements, each single measurement can be
deleted and re-measured in series. Continuously press the key to go back to single-distance
measurement mode.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
VOLUME
2
2
2
1/16
To start the measurement
WARNING!
Do not point the laser dot at persons or animals and do not stare into the laser beam
or view it directly with optical instruments.
NOTE: The laser will switch off after 20 seconds of inactivity. If a measurement has not been
again to turn on the laser.
made within the previous 20 seconds, push measure key
Single distance measurement
1.Press the mode key
to choose the single-distance measurement mode. The mode icon
will blink on the LCD.
to turn on the laser beam. Aim the laser at the target to which you
2. Press the measure key
want to measure.
again to take a measurement. The result is displayed immediately
3. Press the measure key
on the LCD.
NOTE: After choosing Area, Volume or Pythagorean Theorem measurement modes, press the
to switch back to single-measurement mode.
clear key
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
11
OPERATING INSTRUCTIONS
Area measurement
Single pythagorean theorem measurement mode
1.Press the mode key
to choose the area-measurement mode; the mode icon
will
blink on the LCD screen.
to turn on the laser beam; position the tool to aim the laser dot at
2.Press the measure key
the target to which you want to measure.
to take the first length measurement (e.g. length), press the
3.Press the measure key
again to take the second length measurement (e.g. width). The area is
measure key
displayed immediately on the LCD.
The Pythagorean Theorem measurement mode is used to measure distances that cannot be
measured directly because an obstacle would obstruct the laser beam or because no target
surface is available as a reflector. Correct results are achieved only when the laser beam and
the distance to be determined form a precise right angle (90°).
Volume measurement
For this purpose, AB and AC must be
measured. The lines labeled AC and BC must
?
form a right angle.
to choose
1.Press the mode key
the single Pythagorean Theorem
A
measurement mode. The mode icon
C
will blink on the LCD.
to turn on the laser beam; position the tool to aim the laser at the
2.Press the measure key
target B.
to display the measured length of AB in the first row of the
3.Press the measure key
screen.
4.Without changing the location of the measuring reference point on the tool in position A, aim
the laser dot perpendicularly at the target C.
again to display the calculated length of BC in the lowest row of
5.Press the measure key
the screen; the distance AC will be displayed at the same time in the second row.
1.Press the mode key
to choose the volume measurement mode; the mode icon
will
blink on the LCD screen.
to turn on the laser beam; position the tool to aim the laser dot at
2.Press the measure key
the target to which you want to measure.
to take the first length measurement (e.g. length), press the
3.Press the measure key
to take the second length measurement (e.g. width), press the measure key
measure key
to take the third length measurement (e.g. height). The volume is displayed immediately on
the LCD.
In the illustrated example (see fig 3), the
length BC is the unknown distance to be
determined.
fig 3
B
NOTE:
• The distance AC must be shorter than the hypotenuse AB; otherwise the LCD will display “Err
008” to remind you to re-measure the distance AC.
• When taking the two measurements, make sure that they are taken from the same starting
point (A) and that the second measurement is perpendicular to the target C. Taking the
measurements correctly will result in the most accurate calculated distance.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
OPERATING INSTRUCTIONS
14
13
OPERATING INSTRUCTIONS
Double pythagorean theorem measurement
Continuous measurement (locating)
Use the double Pythagorean measurement mode when one end of the length to be measured
indirectly is higher than the measurement position and the other end of that length is lower
than the measurement position.
In the illustrated example (see fig 4), the
fig 4
B
length BC is to be determined, and A is the
measurement position. For this purpose, AB,
?
AO and AC must be measured. AO and BC
must form right angles.
O
A
to choose
1.Press the mode key
the double Pythagorean Theorem
measurement mode. The mode icon
will blink on the LCD screen.
C
to turn on the
2. Press the measure key
laser beam; position the tool to aim the
laser at the target B.
to display the measured length of AB in the first row of the screen.
3.Press the measure key
4.Without changing the measuring reference point location of the tool in position A, aim the
laser beam perpendicularly at the target O.
to display the measured length of AO in the second row of the
5.Press the measure key
screen.
6.Without changing the measuring reference point location of the tool in position A, aim the
laser beam at the target C.
again to display the indirect length of BC in the lowest row of the
7.Press the measure key
screen; the distance AC will be displayed at the same time in the third row.
The continuous measurement function (locating) is used for transferring measurements, e.g., from
construction plans. In the continuous measurement mode, the laser distance finder/measuring tool
can be moved relative to the target, during which time the measured value is updated approximately
every 0.5 seconds in the display. For example, the user can measure the distance from the tool to
a wall and then move away from that wall while the actual distance is continuously updated and
displayed, informing the user when the correct distance has been reached.
to choose the single-distance measurement mode. If in another
1.Press the mode key
to go back to the single-distance measurement mode.
mode, press the clear key
and hold it for about 3 seconds to activate the continuous
2.Press the measure key
measurement mode.
3.Move the tool until the required distance value is indicated at the bottom of the display.
4.Press any key to interrupt the continuous measurement. The current measured value is
indicated in the lowest row of the screen. The minimum and maximum values will be displayed
in the first and second row of the screen.
again to start a new continuous measuring sequence.
5.Press the measure key
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
Minimum/Maximum measurement
This function allows the user to measure the minimum or maximum distance measured from a
fixed measuring point. It is commonly used to measure diagonal distances (maximum values),
horizontal distances, or vertical distance (minimum values).
The resulting value can be transferred to area, volume,Pythagorean Theorem measurement and
single-distance measurement modes.
Min/Max function can help eliminate the measuring deviation caused by holding the tool
incorrectly when aiming at the target. It can help to get an accurate calculation of area, volume
and indirect length.
to choose among area, volume or Pythagorean Theorem
1.Press the mode key
measurement modes.
to activate the min/max function.
2.Press the min/max key
to turn on the laser, aim the laser beam at the target you want to
3.Press the measure key
measure and press it again to start the minimum or maximum measuring.
4.Slowly sweep the laser left and right or up and down over the desired target point.
5.Press any key to interrupt the min/max measuring; the minimum or maximum value will be
displayed on the related row of the screen as an accurate length for calculation.
OPERATING INSTRUCTIONS
16
15
OPERATING INSTRUCTIONS
Addition and subtraction
Error signals
The single-distance, area, volume and indirect length can be added or subtracted with the
addition and subtraction functions.
1.Take the first measurement.
to choose addition or subtraction.
2.Press the plus/minus key
3.Take the second measurement.
4.The sum or difference between the measurements will be displayed in the lowest row of the
screen, and the last measurements will be displayed at the same time in the upper row of
the screen.
5.Follow the same method to make additional calculations.
The following error signals may appear on the LCD of your tool during measuring:
Working with the tripod (available separately)
The use of a tripod is particularly helpful for measuring greater distances. The laser distance
finder/ measuring tool can be screwed onto a commercially available tripod using the 1/4''
thread on the underside of the housing.
1.Mount the tool to the tripod.
2.Set the measuring reference to the thread, the icon shows .
3.Start to take measurements.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
ERROR CODE
CAUSE
ACTION
Err 001
The reflected laser light is too
intense.
Do not direct the laser at a
highly reflective surface; cover
the surface with white paper if
necessary.
Err 002
Out of range, the measuring range
for this tool is from 0.1 to 50 m.
Take measurement within the
range of 0.1 to 50 m.
Err 003
The target provides poor reflection
of the laser.
Change the measuring target or
cover it with a piece of white paper.
Err 004
The temperature is too high.
Wait until the laser distance finder/
measuring tool has reached the
operating temperature (-10 to 50ºC)
Err 005
The temperature is too low.
Wait until the laser distance finder/
measuring tool has reached the
operating temperature (-10 to 50ºC)
Err 006
Low battery, a reminder to replace
the batteries.
Insert new batteries
Err 007
Strong vibration or the tool was
moved quickly when measuring.
Always keep the tool steady
Err 008
Wrong input: the length of one side
of the right triangle as measured is
longer than the hypotenuse.
Re-measure; the hypotenuse is
always longer than the first side
length
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
OPERATING INSTRUCTIONS
18
17
MAINTENANCE
This Laser distance finder/Measuring tool been designed to be a low-maintenance tool.
However, in order to maintain its performance, you must always follow these simple directions.
1.Always handle the tool with care. Treat it as an optical device, such as a camera or
binoculars.
2.Avoid exposing the tool to shock, continuous vibration or extreme hot or cold temperature.
3.Always store the tool indoors. When not in use, ALWAYS store the tool in its protective case.
4.Always keep the tool free of dust and liquids. Use only a clean, soft cloth for cleaning. If
necessary, slightly moisten the cloth with pure alcohol or a little water.
5.Do not touch the lens with your fingers.
6.Check the batteries regularly to avoid deterioration. ALWAYS remove the batteries from the
tool if it is not going to be used for an extended period of time.
is continuously displayed on the
7.Replace the batteries when the empty battery indicator
LCD.
8.Do not disassemble the laser distance finder/measuring tool; this will expose the user to
hazardous radiation exposure.
9.Do not attempt to change any part of the laser lens.
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
Tool cannot be
switched on
Batteries are installed
incorrectly
Reinstall the batteries according to
the polarity indicators in the battery
compartment
Batteries are low voltage
Replaced with new batteries
The power key did not
contact well
Try to press it more firmly or send
for repair
Error codes on
LCD in measuring
Please refer to “Error
signals” above
Please refer to “Error signals” above
Short battery life
Using incorrect batteries
Use alkaline batteries
If the problem remains unsolved after performing the checks described above, call
the toll-free helpline, at 1-800-689-9928.
Battery Disposal
Please dispose the used battery per municipal and provincial law.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
TROUBLESHOOTING
20
19
22
21
No. Part No.
Description
No. Part No.
1
2820226000
Contactor
14 3700479000 Positive Contactor
Description
2
2820227000
Contactor
15 3704437000 Sponge Pad
3
2822565000
Contactor
16 3704438000 Adhesive Tape
4
2823407000
Main Support Assembly 17 3704492000 Sponge
5
3124608000
Battery Cover
18 3705522000 Paster
6
3124609000
Transparent Guard
19 4860008000 Inner Wire
7
3124610000
Cover 20 4890989000 PCB Assembly
8
3124611000
Adjusting base
21 4890920000 PCB Assembly
9
3124612000
Upper Guard
22 5610011000 Tapping Screw
10 3126711000
Push Button
23 5610075000 Tapping Screw
11 3320806000
Right Housing
24 5670252000 Pin
12 3321526000
Left Housing Assembly
25 5690181000 Seal Ring
133660407000 Spring
If any parts are missing or damaged, or if you have any questions,
please call the Toll-free Helpline, at 1-800-689-9928.
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
PARTS LIST
PARTS LIST
Exploded view
WARRANTY
g)this warranty will not apply to any product or part thereof if any part from another
manufacturer is installed therein or any repairs or alterations have been made or attempted
by unauthorized persons;
h)this warranty will not apply to normal deterioration of the exterior finish, including but not
limited to scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive
and chemical cleaners; and
i) this warranty will not apply to component parts sold by and identified as the product of
another company, which shall be covered under the product manufacturer’s warranty, if any.
This Mastercraft product is guaranteed for a period of 3 years from the date of original retail
purchase against defects in workmanship and materials, except for the following components:
Accessories, which are guaranteed for a period of 1 year from the date of original retail
purchase against defects in workmanship and materials. Subject to the conditions and
limitations described below, this product, if returned to us with proof of purchase within the
stated warranty period, and if covered under this warranty, will be repaired or replaced (with
the same model, or one of equal value or specification), at our option. We will bear the cost of
any repair or replacement and any costs of labour relating thereto.
These warranties are subject to the following conditions and limitations:
a)a bill of sale verifying the purchase and purchase date must be provided;
b)this warranty will not apply to any product or part thereof that is worn or broken or that has
become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper
installation, operation or maintenance (as outlined in the applicable owner’s manual or
operating instructions) or that is being used for industrial, professional, commercial or rental
purposes;
c)this warranty will not apply to normal wear and tear or to expendable parts or accessories
that may be supplied with the product that are expected to become inoperative or unusable
after a seasonable period of use;
d)this warranty will not apply to routine maintenance and consumable items, including but not
limited to fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or
adjustments;
e)this warranty will not apply where damage is caused by repairs made or attempted by others
(i.e.: persons not authorized by the manufacturer);
f) this warranty will not apply to any product that was sold to the original purchaser as a
reconditioned or refurbished product (unless otherwise specified in writing);
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
Additional Limitations
This warranty applies only to the original purchaser and may not be transferred. Neither the
retailer nor the manufacturer shall be liable for any other expense, loss or damage, including
but not limited to any indirect, incidental, consequential or exemplary damages arising in
connection with the sale, use or inability to use this product.
Notice to Consumer
This warranty gives you specific legal rights, and you may have other rights, which may vary
from province to province. The provisions contained in this warranty are not intended to limit,
modify, take away from, disclaim or exclude any statutory warranties set forth in any applicable
provincial or federal legislation.
IMPORTED BY MASTERCRAFT CANADA TORONTO, CANADA M4S 2B8
LASER DISTANCE FINDER/MEASURING TOOL - 057-4585-0
WARRANTY
24
23