®
Currency® Single Pedestal Desk
Components
Letter Description
E
T
I
2
Full End Panel
Top
Modesty Panel
NOTE: Assemble as close to
assembled units final desired
location to avoid moving a heavy
unit.
3
1. Remove the drawers from the
pedestal as shown on page 3.
2. Remove shipping strap from
pedestal.
3. Lower the pedestal onto the
underside of T (top). Make sure pins
engage into cams.
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
T
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
© 2012 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Page 1 of 4
939500298 Rev D
®
Fasten Cam Locks in 9 places
(The cam lock screw needs to be turned
o
3/4 full turn or 270 clockwise for
complete engagement.)
Components
Letter Description
E
T
I
5
CLOCKWISE
TURN
Full End Panel
Top
Modesty panel
4. Lower panel I (modesty panel) onto
the top. Lower panel E (full end panel)
onto the top. (Rock modesty panel
slightly for installation) Make sure pins
engage into cams. Tighten all cams.
Level unit by
adjusting glides
in 6 places.
4
I
5. Flip unit over, adjust six (6) glides
and level unit.
6. Reinstall drawers.
E
T
TURN
CLOCKWISE
Fasten Cam Locks in 6 places
(The cam lock screw needs to be turned
3/4 full turn or 270o clockwise for
complete engagement.)
TURN
CLOCKWISE
Fasten Cam Locks in 7 places
(The cam lock screw needs to be turned
3/4 full turn or 270o clockwise for
complete engagement.)
Page 2 of 4
939500298 Rev D
®
Currency Adjustments for Drawer Fronts,
Level Glides and Removal of Box File Drawers
DRAWER FRONT ADJUSTMENT
Leveler adjusts 1/8" in ANY direction.
Remove two (2) or four (4) screws,
that hold the drawer front to the
drawer body.
REMOVE BOX AND FILE DRAWERS
Pull the box or file drawer out until it stops.
Press down on the lock catch on each
side of drawer and pull out on the drawer
as shown.
Alignment is done simply by
loosening the screw and retightening
when alignment has been made.
DRAWER FRONT
DRAWER BODY
LEVEL GLIDES
Adjust glides on bottom of unit
until unit is level.
O 25mm
12mm
Apply stickers on all visible cam joint faces to
cover the connector faces, after assembly.
Page 3 of 4
939500298 Rev D
®
(Tips for Proper Alignment of Parts)
Make sure the cam
lock is located parallel
to the side of the
surface as shown.
CAM LOCK
(See cam lock note)
CAM LOCK NOTE:
If cam lock is installed high on the surface,
tap it down flush with the surface. If that
doesn't work, replace part.
If cam lock is installed low into the surface,
screw cam pin out to extend the length of
the cam pin.
CAM LOCK ADJUSTMENT TOOL
Use mallet, before tightening cam screws, to
bring parts together and avoid light leaks.
TURN
CLOCKWISE
WRONG
Fasten Cam Locks
If the cam lock screw is not
(The cam lock screw needs to
visible, you have installed
be turned 3/4 full turn or 270o
the panel/shelf wrong and
clockwise for complete engagement.)
you need to turn the
panel/shelf 180o.
NOTE: The cam pin is offset and needs to be installed
on the shorter offset side. If the screw heads are not
visible, turn the panel/shelf 180o.
Shorter
off-set side
WRONG
Shorter
off-set side
PANEL
Apply stickers on all visible cam
joint faces to cover the connector
faces, after assembly.
CAM PIN
SCREW HEAD
VISIBLE
SCREW HEAD
NOT VISIBLE
CAM LOCK
NOTE: When assembly has been completed,
make sure to remove all of the E, B, I, ect.
stickers from the surfaces of all the parts.
CAM LOCK
Page 4 of 4
939500298 Rev D