Four-wave mixing based widely tunable
wavelength conversion using 1-m dispersionshifted bismuth-oxide photonic crystal fiber
K. K. Chow1, K. Kikuchi1, T. Nagashima2, T. Hasegawa2, S. Ohara2, and N. Sugimoto2
1
Graduate School of Frontier Sciences, University of Tokyo, Kashiwa, Chiba 277-8561, Japan
2
Asahi Glass Co., Ltd, 1150 Hazawa-cho, Kanagawa-ku, Yokohama 221-8755, Japan
[email protected]
Abstract: We demonstrate widely tunable wavelength conversion based on
four-wave mixing using a dispersion-shifted bismuth-oxide photonic crystal
fiber (Bi-PCF). A 1-meter-long Bi-PCF is used as the nonlinear medium for
wavelength conversion of a 10 Gb/s non-return-to-zero (NRZ) signal. A 3dB working range of the converted signal over 35 nm is obtained with
around 1-dB power penalty in the bit-error-rate measurements.
©2007 Optical Society of America
OCIS codes: (060.4370) Nonlinear optics, fibers; (190.4380) Nonlinear optics, four-wave
mixing
References and links
1. N. Sugimoto, T. Nagashima, T. Hasegawa, S. Ohara, K. Taira, and K. Kikuchi, “Bismuth-based optical fiber
with nonlinear coefficient of 1360 W-1km-1,” in Proc. OFC 2004, Postdeadline paper PDP26, LA, USA
(2004).
2. J. H. Lee, T. Tanemura, T. Nagashima, T. Hasegawa, S. Ohara, N. Sugimoto, and K. Kikuchi, “Use of 1-m
Bi2O3 nonlinear fiber for 160-Gb/s optical-time division demultiplexing based on polarization rotation and
wavelength shift induced by cross-phase modulation,” Opt. Lett. 30, 1267-1269 (2005).
3. J. T. Gopinath, H. M. Shen, H. Sotobayashi, E. P. Ippen, T. Hasegawa, T. Nagashima, and N. Sugimoto,
“Highly nonlinear bismuth-oxide fiber for supercontinuum generation and femtosecond pulse compression,”
J. Lightwave Technol. 23, 3591-3596 (2005).
4. M. Asobe, T. Kanamori, and K. Kubodera, “Ultrafast all-optical switching using highly nonlinear
chalcogenide glass fiber,” IEEE Photon. Technol. Lett. 4, 362-365 (1992).
5. L. Fu, M. Rochette, V. Ta'eed, D. Moss, and B. Eggleton, "Investigation of self-phase modulation based
optical regeneration in single mode As2Se3 chalcogenide glass fiber," Opt. Express 13, 7637-7644 (2005).
6. K. M. Kiang, K. Frampton, T. M. Monro, R. Moore, J. Tucknott, D. W. Hewak, D. J. Richardson, and H. N.
Rutt, “Extruded single-mode non-silica glass holey optical fibres,” Electron. Lett. 38, 546-547 (2002).
7. S. J. B. Yoo, “Wavelength conversion technologies for WDM network applications,” J. Lightwave Technol. 14,
955-966 (1996).
8. O. Aso, A. Shin-Ichi, T. Yagi, M. Tadakuma, Y. Suzuki, and S. Namiki, “Broadband four-wave mixing
generation in short optical fibres,” Electron. Lett. 36, 709-711 (2000).
9. M. Tang, Y. Gong, and P. Shum, “Broad-band tunable wavelength conversion using Raman-assisted
parametric four-wave mixing in highly nonlinear fibers with double-pass geometry,” IEEE Photon. Technol.
Lett. 17, 148-150 (2005).
10. J. H. Lee, W. Belardi, K. Furusawa, P. Petropoulos, Z. Yusoff, T. M. Monro, and D. J. Richardson, “Fourwave mixing based 10-Gb/s tunable wavelength conversion using a holey fiber with a high SBS threshold,”
IEEE Photon. Technol. Lett. 15, 440-442 (2003).
11. K. K. Chow, C. Shu, Chinlon Lin, and A. Bjarklev, “Polarization-insensitive widely tunable wavelength
converter based on four-wave mixing in a dispersion-flattened nonlinear photonic crystal Fiber,” IEEE
Photon. Technol. Lett. 17, 624-626 (2005).
12. J. H. Lee, T. Nagashima, T. Hasegawa, S. Ohara, N. Sugimoto, and K. Kikuchi, “Four-wave-mixing-based
wavelength conversion of 40-Gb/s nonreturn-to-zero signal using 40-cm bismuth oxide nonlinear optical
fiber,” IEEE Photon. Technol. Lett. 17, 1474-1476 (2005).
13. K. Inoue and H. Toba, “Wavelength conversion experiment using fiber four-wave mixing,” IEEE Photon.
Technol. Lett. 4, 69-72 (1992).
14. H. Ebendorff-Heidepriem, P. Petropoulos, V. Finazzi, K, Frampton, R. C. Moore, D. J. Richardson, and T.
M. Monro, “Highly nonlinear bismuth-oxide-based glass holey fiber,” in Proc. OFC 2004, paper ThA4, LA,
USA (2004).
15. T. Nagashima, T. Hasegawa, S. Ohara, and N. Sugimoto, “Dispersion shifted Bi2O3-based photonic crystal
fiber,” in Proc. ECOC 2006, paper We1.3.2, Cannes, France (2006).
#86731 - $15.00 USD
(C) 2007 OSA
Received 21 Aug 2007; revised 1 Nov 2007; accepted 1 Nov 2007; published 6 Nov 2007
12 November 2007 / Vol. 15, No. 23 / OPTICS EXPRESS 15418
16. T. Nagashima, T. Hasegawa, S. Ohara, and N. Sugimoto, “Fusion-spliceable Bi2O3-based photonic crystal
fiber,” in Proc. OFC 2007, paper OTuC5, Anaheim, USA (2007).
17. K. Kikuchi and C. Lorattanasane, “Design of highly efficient four-wave mixing devices using optical fibers,”
IEEE Photon. Technol. Lett. 6, 992-994 (1994).
1. Introduction
The development of highly-nonlinear fibers (HNLF) fabricated by novel glass materials has
opened a new window for nonlinear fiber optics owing to its ultra-high nonlinearity and
compatible to standard single-mode fibers (SMF). Much research effort has been focused on a
large variety of nonlinear applications and compact, efficient devices have been demonstrated
with fibers fabricated by bismuth-oxide glass [1-3], chalcogenide glass [4, 5], heavy metaloxide glass [6], etc. Among different kinds of signal processing applications in large capacity
communication networks, wavelength conversion plays a major role in providing wavelength
flexibility and avoiding wavelength blocking in the wavelength-division-multiplexing (WDM)
systems. In particular, four-wave mixing (FWM) is a promising technique for wavelength
conversion owing to its ultra-fast response and high transparency to bit rate and modulation
format [7]. Previous reports on FWM-based wavelength conversion using conventional silica
HNLF [8, 9] or silica photonic crystal fibers (PCF) [10-11] have shown good performances
with effectively shortening the required fiber length from kilometers to tens of meters.
Recently, report on FWM-based wavelength conversion using highly-nonlinear bismuth-oxide
fiber (Bi-NLF) has successfully shortened the required fiber length to even less than 1 meter
[12]. However, one major issue of Bi-NLF applications falls on its high material dispersion
similar with other non-silica HNLF with novel glass materials, which limits the wavelength
working range. In general, HNLF made by different novel glass materials can have extremely
high nonlinearity but at the same time suffer from large group velocity dispersion (GVD). In
order to obtain wideband FWM for efficient wavelength conversion, the fiber should have
high nonlinearity, low dispersion, and short in length [13]. Recent reports show that one
effective solution to solve the dispersion problem of Bi-NLF is applying photonic crystal
structure to the fibers [14, 15]. In this paper, we experimentally demonstrate a compact,
widely tunable wavelength converter using 1 meter of newly developed dispersion-shifted
bismuth-oxide photonic crystal fiber (Bi-PCF). By combining its advantages of higher
nonlinearity than silica based PCF and adjusted dispersion in the 1550 nm range, a wide
working range of 35 nm is obtained. Also, the Bi-PCF is fully spliced to SMF without free
space coupling so that the converter can have a stable operation. A power penalty of around
1.2 dB is measured for 10 Gb/s non-return-to-zero (NRZ) signal in the bit-error-rate (BER)
measurements.
2. Fiber Design for Wideband Four-Wave Mixing
The wideband FWM wavelength converter comes from the adoption of fiber with high
nonlinearity and low dispersion in the 1550 nm range. In particular, maintaining phase
matching between the signal and the pump plays important role in generating effective FWM
effect. It is difficult to maintain phase matching in a long fiber due to GVD. Previous work
shows that the phase mismatch problem even exists in less than 1 meter Bi-NLF with a
dispersion value D of -260 ps/nm/km at 1550 nm and limits the tunability [12]. In order to
obtain an efficient wideband FWM effect, one ultimate solution is to adopt photonic crystal
structure in the Bi-NLF to modify its dispersion characteristics.
In our experiment, we have adopted a dispersion-shifted Bi-PCF as the nonlinear medium.
The inset of Fig. 1 shows the microstructured region of the fiber which is fabricated by the
inflating method [15]. Firstly, glass rods are prepared by a conventional melting method and 6
holes are drilled in a rod with encircling the center. A single hole is drilled in the center of
another rod as jacketing tube. Then the rod with 6 holes is drawn to proper diameter in order
to be inserted into the jacketing tube. The rod together with the jacket is drawn simultaneously
#86731 - $15.00 USD
(C) 2007 OSA
Received 21 Aug 2007; revised 1 Nov 2007; accepted 1 Nov 2007; published 6 Nov 2007
12 November 2007 / Vol. 15, No. 23 / OPTICS EXPRESS 15419
3 dB
coupler
FFP
Receiver/
BERT
`
10 Gb/s
NRZ signal
EDFA
1.09 m Bi-PCF
Tunable CW
laser
50 μm
5 μm
Fig. 1. Experimental setup on widely tunable wavelength conversion using a dispersion-shifted
bismuth-oxide photonic crystal fiber. The inset shows the mircrostructured region of the fiber [12]. BiPCF: bismuth-oxide photonic crystal fiber; EDFA: erbium-doped fiber amplifier; FFP: tunable fiber
Fabry-Perot filter; BERT: bit-error rate test set.
with applying positive pressure on 6 holes and negative pressure on the gap between the rod
and the jacket. Through this process 6 holes are expanded and the core diameters can be
adjusted by appropriate design of jacketing tube geometry and number of rod-in-tube [15]. By
varying the core and hole diameters, the dispersion of the fiber can be shifted. With this
structure, we have fabricated a fiber with a mode filed diameter (MFD) of 2.01 μm, and a
dispersion value D of -9.9 ps/nm/km at 1550 nm measured by the homodyne interferrometric
method (Agilent 81901A). Since there is a trade-off between dispersion-shift and nonlinearity,
the fiber has a nonlinear coefficient of around 580 W-1km-1. Also, the attenuation of the fiber
is 1.9 dB/m in the 1550 nm range. Table 1 summarizes the optical parameters of Bi-PCF in
our experiment, Bi-NLF in [12] and common silica HNLF. The Bi-PCF segment adopted in
the experiment is 1.09 meters in length with both ends spliced to standard single-mode fiber
(SMF), yielding a total loss of 11.9 dB. An updated report on Bi-PCF splicing shows that with
perfect MFD conversion in the end of collapsed hole region, the fiber can play like the step
index Bi-NLF with core diameter of 1.6 μm and MFD of 5.5 μm in which the theoretical
splicing loss to SMF can be 1.8 dB/point. [16]. Note that unlike common silica PCF to SMF
splicing, there is no intermediate fiber spliced between Bi-PCF and SMF so that there is no
extra reflection from the 2 more splicing points.
Table 1. Optical parameters of Bi-PCF, Bi-NLF, and common silica HNLF
Parameters
Bi-PCF
Bi-NLF
HNLF
Nonlinearity (W-1km-1)
580
1100
15.5
Dispersion @ 1550 nm (ps/nm/km)
-9.9
-260
1.7
Effective area (μm )
3.17
3.08
11
Propagation loss (dB/m)
1.9
0.8
0.0016
2
3. Experiment and Discussion
The experimental setup on tunable wavelength conversion using Bi-PCF is shown in Fig. 1.
The input signal is a 231-1 bits pseudorandom NRZ signal at 10 Gb/s. The input signal is
combined with a wavelength tunable continuous-wave pump laser using a 3-dB coupler. The
#86731 - $15.00 USD
(C) 2007 OSA
Received 21 Aug 2007; revised 1 Nov 2007; accepted 1 Nov 2007; published 6 Nov 2007
12 November 2007 / Vol. 15, No. 23 / OPTICS EXPRESS 15420
combined signal is then launched on an erbium-doped fiber amplifier (EDFA) followed by a
segment of 1.09 m long (excluding fiber pigtails) dispersion-shifted Bi-PCF. The launched
pump power is estimated to be around 22.5 dBm. It is worth noting that there is no stimulated
Brillouin scattering (SBS) observed at this pump power level without any (SBS) suppression
scheme in the experiment as the estimated SBS threshold is around 31 dBm. This comes from
a relatively high SBS threshold with such a short length of fiber with less accumulated
Brillouin gain [13]. The amplified pump and signal then undergo FWM effect and generate
new wavelength components. Finally, we use a tunable fiber Fabry-Perot filter (FFP) to filter
out the converted signal and wavelength conversion is obtained.
Figure 2 shows the spectra obtained after the Bi-PCF at different converted wavelengths.
In our experiment the input signal (S) is fixed at 1550.0 nm and different converted
wavelengths are obtained by tuning the pump (P) wavelength. Figures 2(a) and 2(b) are the
spectra showing the up conversion to 1553.9 and 1563.4 nm, respectively. Figures 2(c) and
2(d) show the output spectra of down conversion to 1544.5 and 1536.7 nm, respectively. Note
that the optical signal to noise ratio (OSNR) of the converted signal is maintained over 20 dB
over the whole working range.
We define the conversion efficiency as the ratio of converted signal power to input signal
power inside the Bi-PCF, excluding the fiber input and output coupling losses of 4.4 dB and
5.4 dB, respectively. The relation between the conversion efficiency and the converted output
wavelength is plotted in Fig. 3. For the case of partially degenerate FWM, when the signal and
pump wavelengths are close enough the conversion efficiency η can be expressed as [1]:
S
P
Spectral Intensity (20 dB/div)
C
(a)
S
P
C
(b)
P
S
C
(c)
P
S
C
(d)
1530
1540
1550
1560
1570
Wavelength (nm)
Fig. 2. Output four-wave mixing spectra after Bi-PCF showing (a)(b) up conversion and
(c)(d) down conversion. S: input signal; P: pump; and C: converted signal.
#86731 - $15.00 USD
(C) 2007 OSA
Received 21 Aug 2007; revised 1 Nov 2007; accepted 1 Nov 2007; published 6 Nov 2007
12 November 2007 / Vol. 15, No. 23 / OPTICS EXPRESS 15421
η (L ) = (γPav L ) 2
(1)
where L is the propagation distance, γ is the nonlinear coefficient, and Pav is the path average
pump power:
Pav = P[1 − exp (− αL )] / αL
(2)
with input pump power P and fiber loss coefficient α. From Eq. (1) the peak conversion
efficiency is calculated as -20.9 dB, which is consistent with the experimental results.
With tuning the pump wavelength thus the converted wavelength, a 3-dB working range
of the converted signal is observed over 35 nm from 1532 to 1567 nm in our experiment.
Consider the case when signal and pump wavelengths are detuned away, the conversion
wavelength tunability is limited by the finite phase mismatch Δk = β2 Ω 2 caused by the fiber
GVD, where β2 is the GVD parameter at the pump wavelength and Ω is the optical frequency
shift between signal and pump waves. Thus, the conversion range is limited by frequency shift
hence phase mismatch as [17]:
η (L ) = ⎢γPav L
⎡
⎣
sin (ΔkL / 2 ) ⎤
ΔkL / 2 ⎥⎦
2
(3)
Note that the bandwidth of η in Eq. (3) is defined with the case using fixed pump and tuning
input signal, which is different from this experiment where the pump wavelength is tuned. In
another experiment, we have investigated the fixed pump FWM case using the same segment
of Bi-PCF. By Eq. (3) and the experimental results we find that the β2 value of the fiber is
around 23 ps2/km at 1550 nm, which is around -18 ps/nm/km when converted to D value. The
measured β2 value by such method is in the same order of magnetite consistent with that of
mentioned in the pervious session. However, due to the very short length of fiber adopted in
our experiment, a strictly precise measurement of dispersion parameters is still difficult to
obtain. Although the β2 value of the Bi-PCF is still higher than that of conventional solid-core
highly-nonlinear fiber, combining the advantages of high nonlinearity and short fiber length
we can still obtain wideband wavelength conversion.
0
)B- 10
d(
yn - 20
eic
if
E- 30
noi
sr
ev - 40
no
C- 50
- 60
1525
1535
1545
1555
Converted Wavelength (nm)
1565
1575
Fig. 3. Plot of conversion efficiency against converted signal wavelength.
#86731 - $15.00 USD
(C) 2007 OSA
Received 21 Aug 2007; revised 1 Nov 2007; accepted 1 Nov 2007; published 6 Nov 2007
12 November 2007 / Vol. 15, No. 23 / OPTICS EXPRESS 15422
-3
-4
-5
)
R
EB
(
g
o
l
6
-7
-8
-9
back-to-back
15 nm down-convert
10 nm down-convert
15 nm up-convert
10 nm up-convert
- 10
- 28
- 26
- 24
- 22
- 20
- 18
- 16
- 14
- 12
Received Power (dBm)
Fig. 4. Plot of bit-error rate against received optical power. Inset (upper) and (lower) show
the 10 Gb/s eye-diagrams of input and 15 nm down-converted signal, respectively.
In order to investigate the system performance of the wavelength converter, 10 Gb/s BER
measurements are performed. The wavelength of input signal is fixed at 1550 nm and the
BER of both up and down conversion are measured. Figure 4 plots the output BER against the
received optical power of different converted wavelengths. The insert shows the 10 Gb/s eye
diagram of the input signal and the 15 nm down-converted signal. The power penalties
measured of all converted wavelengths are ranging from 1.2 to 1.4 dB at 10-9 BER level,
which shows that error-free conversion with similar properties can be obtained within the
whole wavelength tuning range. The BER performance tends to drop when tuning beyond 15
nm up- or down-conversion and no 10-9 BER level can be obtained outside the 1532-1567 nm
range. The around 1 dB power penalty is believed to be originated from the multi-path
reflection between the two splicing points of the fiber, as the refractive index of bismuthoxide glass can be as high as 2.1 at 1550 nm. Based on such power penalties it is believed that
the wavelength converter can work with higher data rate. With the technical improvement of
the Bi-PCF splicing as mentioned, both the power penalty and the conversion efficiency can
be improved. Previous work on silica PCF shows that the dispersion can be precisely tailormade with different kinds of core and hole structures. With the compatible bismuth-oxide
glass such PCF technologies can be applied and Bi-PCF with different dispersion
characteristics can be obtained to fit specific applications.
4. Conclusion
A 1-meter-long dispersion-shifted bismuth-oxide photonic crystal fiber has been adopted to
experimentally demonstrate a four-wave mixing based widely tunable wavelength converter.
A 3-dB working range up to 35 nm of the converted signal with around -20 dB conversion
efficiency over 1532-1567 nm has been achieved. Also, power penalties of around 1 dB with
different converted wavelengths are measured in the 10 Gb/s BER measurements.
Improvement of the splicing loss and more precise dispersion control of Bi-PCF are
foreseeable so that results with lower power penalty, higher conversion efficiency and wider
conversion range are expected in the near future.
Acknowledgement
This work was supported by Special Coordination Funds for Promoting Science and
Technology.
#86731 - $15.00 USD
(C) 2007 OSA
Received 21 Aug 2007; revised 1 Nov 2007; accepted 1 Nov 2007; published 6 Nov 2007
12 November 2007 / Vol. 15, No. 23 / OPTICS EXPRESS 15423