User’s Guide
CVIDF20xx-15x Analog CCT Video Copper-toFiber Video Receiver
Single and dual channel video receiver card features:
Dual
•
•
•
•
•
•
•
•
•
•
Plug-and-play design for easy installation
CCTV video equipment compatible
One-way signal transmission through the system
AM Video
NTSC, PAL, SECAM compatible
Automatic Gain Control (AGC)
Real time full color video
Link Pass Through
Single or dual video channel configuration
Automatic gain control (contrast and brightness)
The CVIDF20xx-15x video receiver, when paired with
Transition’s camera-mounted transmitter J/VD-Tx-01,
enables the transport of analog CCTV video over a fiber
infrastructure for extended reach video surveillance or
security installations. In extended fiber receiver mode, the
RX sensitivity can be adjusted to accommodate greater
distances.
The chassis card is available in a single video channel or a
dual video channel configuration. All video conversion is
performed in real time. The automatic Gain Control (AGC)
feature automatically adjusts the video contrast and
brightness to maintain the quality and integrity of the
original video stream.
Single
Installation . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . .4
Cable Specification . . . . . . . . . . .5
Technical Specifications . . . . . . . .5
Troubleshooting . . . . . . . . . . . . . .6
Contact Us . . . . . . . . . . . . . . . . . .7
Compliance Information . . . . . . . .8
CVIDF20xx-15x
CVIDF20xx-15x
The video receiver system has the following types of connectors.
Connector Type
75-Ohm BNC
Fiber
Quantity
2
2
Distance
75-Ohm coax cable, 228m (750ft)
Model dependent (see below)
The various fiber connections are available on separate models. Single mode and
multimode receivers come in the following configurations.
Model
CVIDF2011-150
Video Receiver (Single)
CVIDF2011-155
Video Receiver (Dual)
CVIDF2013-150
Video Receiver (Single)
CVIDF2013-155
Video Receiver (Dual)
CVIDF2012-150
Video Receiver (Single)
CVIDF2012-155
Video Receiver (Dual)
Optic Fiber
ST, multimode, 850 nm
Distance
1km (0.6miles) standard
2km (1.2miles) extended
(2)ST, multimode, 850 nm
1km (0.6miles) standard
2km (1.2miles) extended
SC, multimode, 850 nm
1km (0.6miles) standard
2km (1.2miles) extended
(2)SC, multimode, 850 nm
1km (0.6miles) standard
2km (1.2miles) extended
ST, single mode, 1310 nm
10km (6.2miles) standard
20km (12.4miles) extended
(2)ST, single mode, 1310 nm 10km (6.2miles) standard
20km (12.4miles) extended
Installation -- continued
J1 and J5 are distance configuration connectors. Position “S” is for standard distances
and “X” is for extended distances. The distances are model dependent.
Installing video card in a Point System chassis
To insert the video card, do the following:
1. Wearing a ground strap, slide the card into an available slot in the Point System
chassis. See photo below.
2. Push the card all the way into the slot (should snap in).
3. Push in and turn the screw clockwise to secure the card to the chassis frame.
Installation
Card handling
1. Keep the CVIDF20xx-15x card in its anti-static bag until ready to install.
2. Wear a grounding strap when removing the card from its anti-static bag.
Distance configuration shunt
The CVIDF20xx-15x card come with a shunt installed in the “S” position on connector
J1 (single channel) and J1/J5 (dual channel) as shown below.
Setting up the video system
Equipment needed:
•
J/VD-TX-01 fiber transmitter (single or multimode)
•
CVIDF20xx-15x video card (single or multimode)
•
Video camera
•
Monitor
•
Coax cable
•
Fiber cable
Note: The video transmitter and receiver must be matched: single mode TX/RX or
multimode TX/RX. If installed as a mixed pair, the system will not function.
Caution: Use 75 ohm BNC connectors on 75 ohm cable only. Failure to observe this
caution will result in signal degradation.
Note: See J/VD-TX-01 fiber transmitter manual (#33349) available on the web @
transition.com for specifics.
2
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
[email protected] -- Click the “Transition Now” link for a live Web chat.
3
CVIDF20xx-15x
CVIDF20xx-15x
Setting up video system -- continued
Operation -- continued
To install the video transmitter and receiver system cables, see installation diagram
below.
LED
Description
1
RX2 (Receive)
2
RX1 (Receive)
3
PWR (Power)
ON solid green = fiber cable connect/receiving data
Off = No power or cable disconnected
ON solid green = fiber cable connect/receiving data
Off = No power or cable disconnected
ON Green Powered
OFF No Power
Dual Channel Video System
Monitor
75-Ohm BNC Coax Cable
•
Make sure that power is supplied to the transmitter, receiver, and camera,
with the monitor turned ON.
•
The system is operational when the camera feed appears on the monitor.
Coax*
Fiber
Camera
J/VD-TX-01
Transmitter
Cable specifications
Coax cable
Point System
Chassis
with
CVIDF20xx-15x
Receiver Card
RG Type:
Gauge:
Impedance:
Distance:
RG-59, RG-6
18–25, single conductor
75 ohms
228 M (750 ft) Max
Single Mode
Multimode
9/125μ
62.5/125μ
Multimode
Wavelength:
Link Budget:
850 nm
6.0 db or 11.0 db
Single Mode
Wavelength:
Link Budget:
1310 nm
10.0 db or 15.0 db
Fiber
75-Ohm BNC Coax Cable
Monitor
Fiber
J/VD-TX-01
Transmitter
Camera
Directly Mounted Camera
*75-Ohm BNC Coax Cable
Technical Specifications
Operation
Use 75-ohm BNC connectors on 75-ohm cable only.
LEDs
The following shows LED locations and an explanation of each follows:
2
4
Video formats:
NTSC, PAL, SECAM
Video spec
3
1
Transition Networks models CVIDF20xx-15x video receiver specifications for
all six models.
RX 2
R X1
P WR
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Input Video:
Bandwidth:
Differential gain:
Differential phase:
Tilt:
Signal/Noise Ratio:
0.5 to 2-volt pk-pk (75 ohms)
5 Hz - 10 MHz
<5%
< 5°
< 1%
60dB
[email protected] -- Click the “Transition Now” link for a live Web chat.
5
CVIDF20xx-15x
CVIDF20xx-15x
Technical Specifications -- continued
Power consumption:
Single card 2 watts; dual card 3 watts
Power supply:
12 V – chassis AC
Operating temperature:
0°C to 60°C (32°F to 140°F)
Storage temperature:
-25°C to 85°C (13°F to 185°F )
Humidity:
Altitude:
5% to 95%, non-condensing
0 to 10,000 feet
Dimensions:
0.86”W x 5.0”D x 3.4”H (22 mm x 127 mm x 86 mm)
Warranty:
Lifetime
The information in this user’s guide is subject to change. For the most up-to-date
information on the CVIDF20xx-15x video receiver, view the user’s guide on-line at:
www.transition.com.
Troubleshooting
If there are problems with the system setup or a system failure occurs, isolate and
correct the problem by determining the answers to the following questions and then
taking the indicated action:
1.
Is the power LEDs ON on the receiver?
Contact Us
Technical support
Technical support is available 24 hours a day.
US and Canada:
1-800-260-1312
International:
00-1-952-941-7600
Transition now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-based seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff.
[email protected]
Address
Transition Networks
6475 City West Parkway, Minneapolis, MN 55344, U.S.A.
telephone: 952-941-7600, toll free: 800-526-9267, fax: 952-941-2322
NO
•
•
•
•
Is the power to the chassis ON?
Is the card fully inserted ?
Is the power on LED lit?
Contact Technical Support: US/Canada: 1-800-260-1312, International: 00-1952-941-7600.
YES
• Proceed to step 2.
2.
Are the RX LED lit on the receiver?
NO
• Check that the fiber cable SM/MM matches the transmitter and receiver set
SM/MM.
• Check the fiber-cable connections and condition of the fiber cable.
• Check for video signal at the transmitter coax port.
• Check the coax cable connection.
• Contact Technical Support: US/Canada: 1-800-260-1312, International: 00-1952-941-7600.
Declaration of Conformity
Name of Mfg:
Transition Networks
6475 City West Parkway, Minneapolis MN 55344 U.S.A.
Model:
CVIDF2011-150, CVIDF2011-155,CVIDF2013-150,
CVIDF2013-155, CVIDF2012-150, CVIDF2012-155 Video
Receivers
Part Number(s):
CVIDF20xx-15x
Regulation:
EMC Directive 89/336/EEC
Purpose: To declare that the CVIDF20xx-15x to which this declaration refers is in
conformity with the following standards:
CISPR 22:1997+A1:2000; EN 55022 Class A; EN 55024:1998+A1:2000 Class A; FCC
part 15 subpart B; CFR 21 subpart J
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
Sept, 2006
Stephen Anderson, Vice-President of Engineering
Date
YES
• Contact Technical Support: US/Canada: 1-800-260-1312, International: 00-1952-941-7600.
6
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
[email protected] -- Click the “Transition Now” link for a live Web chat.
7
CVIDF20xx-15x
Compliance Information
FCC Class A; EN55022 Class A; EN55024;
CE Mark
FCC regulations
This equipment has been tested and found to comply with the limits for a class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at the user's own expense.
Canadian regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out
on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.
European regulations
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
ACHTUNG! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei
Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für
Gegenmaßnahmen verantwortlich.
ATTENTION! Ceci est un produit de Classe A. Dans un environment domestique, ce produit
risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les
measures spécifiques appropriées.
In accordance with European Union Directive 2002/96/EC of the European Parliament
and of the Council of 27 January 2003, Transition Networks will accept post usage returns
of this product for proper disposal. The contact information for this activity can be found
in the 'Contact Us' portion of this document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EGMitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
Trademark notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright restrictions
© 2003, 2005 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means graphic, electronic, or mechanical - without written permission from Transition Networks.
8
Printed in the U.S.A
33354.A