Quick Start Guide - ATV212
ENGLISH
S1A5382501
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Read and understand this quick start guide before performing any procedure with this drive.
• The user is responsible for compliance with all international and national electrical code requirements with respect to grounding of all
equipment.
• Many parts of this drive, including the printed circuit boards, operate at the line voltage. DO NOT TOUCH. Use only electrically insulated tools.
• DO NOT touch unshielded components or terminal strip screw connections with voltage present.
• DO NOT short across terminals PA/+ and PC/- or across the DC bus capacitors.
• Before servicing the drive:
- Disconnect all power, including external control power that may be present.
- Place a "DO NOT TURN ON" label on all power disconnects.
- Lock all power disconnects in the open position.
- WAIT 15 MINUTES to allow the DC bus capacitors to discharge.
- Measure the voltage of the DC bus between the PA/+ and PC/- terminals to ensure that the voltage is less than 42 Vdc.
- If the DC bus capacitors do not discharge completely, contact your local Schneider Electric representative. Do not repair or operate
the drive.
• Install and close all covers before applying power or starting and stopping the drive.
Failure to follow these instructions will result in death or serious injury.
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider
Electric for any consequences arising out of the use of this product.
Information below is designed to use single drive connected to single motor with a motor cable length less than 50 meters (164 ft).
In any other case, consult the ATV212 installation manual and programming manual on www.schneider-electric.com.
Check your cables before connecting the drive with motor (length, power, shielded or unshielded). Motor cable length is _______(< 50 meters, 164 ft).
1
Check the delivery of the drive
• Remove ATV212 from the packaging and check that it has not been damaged.
WARNING
DAMAGED DRIVE EQUIPMENT
Do not operate or install any drive or drive accessory that appears damaged.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
• Check that the drive reference printed on the label is the same as that on the delivery note corresponding to the
purchase order.
ATV212HU15N4
1.5KW - 2HP - 380 / 480V
Write the drive Model Reference: _____________ ___________and Serial Number: ____________________________
2
Check the line voltage compatibility
• Check that the line voltage is compatible with the supply range of the drive.
Line voltage _______ Volts
Drive voltage range _______ Volts
Drive range: ATV212 pppp M3X = 200 ... 240 V three-phase / ATV212 pppp N4p = 380 ... 480 V three-phase.
3
8B0915316127
Mount the drive vertically
For a surrounding air temperature up to 40 °C (104 °F).
ATV212W
(a)
(a)
(a)
(a)
50 mm (2 in.)
(a)
(c)
(b)
(a)
(b)
(a)
ATV212H
(b)
100 mm (4 in.)
(c)
10 mm (0.4 in.)
See installation manual on www.schneider-electric.com for other thermal conditions.
www.schneider-electric.com
1/4
S1A53825 - 10/2010
4
Connect the drive: Power
Connect the drive:
Control choice
5
• Wire the drive to the ground.
• Check circuit breaker rating or fuse rating.
• Check that the motor voltage is compatible with the drive voltage.
Motor voltage ______Volts.
• Wire the drive to the motor.
• Wire the drive to the line supply.
[REMOTE configuration]
5.1 (Control by external reference)
0,6 N.m
5.3 lb.in
• Wire the speed reference:
PP: Internal supply for
analogue inputs
VIA: Analog/ logic input
CC: Common
ATV 2 12
PP
200...240 V
ATV212 M3X
RUN
2.2 to 10 kΩ
%
PRG
CC
VIA
Hz
MON
Loc
Rem
• Wire the command:
MODE
ENT
RUN
STOP
or
Control command 2-wire:
380...400 V
F: Run forward
ATV 2 12
R: Run reverse
P24: Internal supply
F
for logic inputs
ATV212 N4
P24
R
Do:
6 + 7 + 8 + 9.1
Do:
6 + 7 + 8 + 9.1
Do:
6 + 7 + 8 + 9.2
Control command 3-wire:
F: Run forward
R: Stop
RES: Run reverse
P24: internal supply
for logic inputs
Note: for ATV212H075ppp, ATV212HU15ppp, ATV212HU22ppp, to connect power,
open the door, remove the terminal board, connect R/L1, S/L2 ,T/L3 and fix again
the terminal board.
ATV 212
F
R
RES
P24
[LOCAL configuration]
5.2 (control by internal reference).
Loc
Rem
6
Apply power to the drive
• Check that used Logic Inputs are not active (see F, R, RES, P24, open circuit).
• Apply power to the drive.
Run
• At each power on , drive displays HELLO message, then run mode : mode
0.
.0
7
Hz
Set motor parameters
• See on the motor Nameplate to set the following parameters.
Menu
Code
Description
Pt
[Mot cont. mode sel.]: Motor control mode
0 [Constant V/Hz]: Constant V/Hz
1 [Variable Torque]: Variable torque
2 [Cst V/Hz+Boost]: Constant V/Hz with automatic torque boost
3 [SVC]: Sensorless vector control
4 [Economy]: Energy saving
[Upper limit freq]:
Nominal motor frequency on motor nameplate (Hz)
[Motor Rated Voltage]:
Nominal motor voltage on motor nameplate (V)
[Motor rated current]:
Nominal motor current on motor nameplate (A)
[Motor rated speed]:
Nominal motor speed on motor nameplate (rpm)
[Motor Current Limit]:
AUF
[QUICK MENU]
uL
uLu
F415
F--[EXTENDED MENU]
F417
F601
www.schneider-electric.com
Factory setting
Limit current during motoring or braking (%)
2/4
Customer
setting
1
50.0
drive rating
drive rating
drive rating
110
S1A53825 - 10/2010
Set motor parameters (continued)
7
Menu
Code
F--[EXTENDED MENU]
Description
F400
Customer
setting
Factory setting
Set F400 [Auto-tuning drive] parameter to 2. The drive
displays Atn1, the message disappears after a few seconds
0
Auto-Tunning for uLu, uL, F415 and F417
DANGER
WARNING
HAZARD OF ELECTRIC SHOCK OR ARC FLASH
DAMAGED DRIVE EQUIPMENT
• During auto-tuning, the motor operates at rated
current.
• Do not service the motor during auto-tuning.
• It is essential that the following parameters uLu, uL, F415 and
F417 are correctly configured before starting autotuning.
• When one or more of these parameters have been changed after autotuning has been performed, F400 will return 0 and the procedure
will have to be repeated.
Failure to follow these instructions will result in death
or serious injury.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Set basic parameters
8
Menu
Code
Description
AU1
[Auto ramp] Automatic ramp adaptation:
0 [Disabled]
1 [Enable] - (ACC) and (dEC)
2 [ACC only]
[Acceleration time 1]:
Acceleration ramp and the time(s)
[Deceleration time 1]:
Deceleration ramp and the time (s)
[Low limit frequency]:
Motor frequency at minimum reference (Hz)
[High speed]:
Motor frequency at maximum reference (Hz)
[Motor thermal prot.]:
Motor Rated Current Overload Setting (%)
[Switch. freq. level]
Switching Frequency Level (kHz)
Increasing the switching frequency may reduce audible motor noise.
See the derating curves in the ATV21 2Installation Manual.
ACC
AUF
[QUICK MENU]
dEC
LL
UL
tHr
F---
[EXTENDED
MENU]
9
F300
Customer
setting
Factory setting
1
ATV21 2 y 15KW = 10 s
ATV212 u 18KW = 30 s
0. 0
50.0
100
8 to12
Set control choice
9.1 [REMOTE configuration]
9.2 [LOCAL configuration]
Parameters factory settings:
2-wire control
Menu
_
F--[EXTENDED
MENU]
Code
CMOd [Command mode sel]
F111 [LI F selection]
F112 [LI R selection]
Setting
0 [Logic inputs]
2 [forward]
RUN
%
PRG
Hz
MON
3 [reverse]
Loc
Rem
MODE
3-wire control
Menu
_
F--[EXTENDED
MENU]
10
ENT
Code
CMOd [Command mode sel]
F111 [LI F selection]
F112 [LI R selection]
F113 [LI RES selection]
Setting
0 [Logic inputs]
2 [forward]
49 [3-wire]
3 [reverse]
RUN
STOP
RESET
Start the motor
www.schneider-electric.com
3/4
S1A53825 - 10/2010
Menus structure
Programming
mode
Run
mode
RUN
0.
.0
MODE
Hz
PRG
ATV212
drive
Power Up
AUF
Monitoring
mode
Submenu
[Quick menu]
ENT
Submenu
[ALL PARAM CHANGE]
GrU
MODE
MODE
AU1
[Auto ramp]
F---
Submenu
[EXTENDED MENU]
ACC
[Acceleration time 1]
IO
Submenu
[I/O MENU]
dEC
[Deceleration time 1]
COM
Submenu
[COMMUNICATION MENU]
LL
[Low limit frequency]
Sr7
[Preset speed 7...1]
UL
[Upper limit freq]
OLM
[Motor overload prot]
tHr
[Motor thermal prot.]
tHr
[Motor thermal prot.]
FM
[AO scaling]
ub
[Mot Voltage Boost]
Pt
[Mot cont. mode sel.]
uL
[Motor rated freq.]
uLu
[Motor rated voltage]
[Motor rated voltage]
uLu
uL
Hz
[Motor rated freq.]
[Low limit frequency]
UL
[Upper limit freq]
FH
Fr-F
[Direction]
MODE
(1)
t0.10
[Drive run time 100h]
Nbiii
[Mdb com stat]
Niiii
[Drive service alarm]
[Past fault]
n 50
[Comm. counter 1]
N 50
[Comm. counter 2]
1500
[Motor speed rpm]
A16.5
[Drive out. rat. cur. A]
H 75
[Total motor power]
h 85
[Total input power]
b 70
(1)
LL
Fr-F
nErr
MODE
[Mot cont. mode sel.]
Pt
MON
Fr-F = forward direction
Fr-r = reverse direction
d 50
Hz
[PID computed ref.]
[PID feedback]
Hz
MODE
uE01
[Memory ver.]
[Max frequency]
uc01
[CPU MMI ver.]
dEC
[Deceleration time 1]
u101
[CPU CTRL ver.]
ACC
[Acceleration time 1]
0 il
Fr
[Local mot. direction]
iii
tYP
[Parameter reset]
FM
[AO scaling]
H 75
[Output power KW]
FMSL
[AO funct. selection]
h 80
[Input power KW]
FMOd
[Frequency mode sel]
L 70
CMOd
[Command mode sel]
c 90
AU4
[Auto set function]
q 60
AU1
[Auto ramp]
P100
AUH
Submenu
[5 LAST PARAM CHANGE]
Y100
MODE
o60.0
[Relay map]
[LOGIC INPUT MAP]
Hz
%
%
%
%
%
%
C 80
[Motor frequency]
[Drive load %]
[Torque current]
[Motor torque %]
[Motor voltage]
[Line voltage]
[Motor current]
Refer to the programming manual for comprehensive menu description
F60.0
www.schneider-electric.com
4/4
Hz
[Speed reference]
S1A53825 - 10/2010