C H A P T E R
20
RST Commands
This chapter provides RST (restore) commands for the Cisco ONS 15454 SDH.
20.1 RST-<MOD2>
Restore (10GFC, 10GIGE, 1GFC, 1GFICON, 2GFC, 2GFICON, CLNT, D1VIDEO, DS3I, DV6000, E1,
E3, E4, ESCON, ETRCLO, FSTE, G1000, GFPOS, GIGE, HDTV, ISC1, STM4, STM64, STM1,
STM16, OCH, OMS, OTS, POS, STM1E, VC3, VC44C, VC38C, VC464C, VC48C, STS36C, VC4,
VC416C, VC42C, VC43C, VC11, VC12)
Usage Guidelines
This command provisions a facility in service.
See Table 27-1 on page 27-1 for supported modifiers by platform.
Category
Facility
Security
Maintenance
Cisco ONS 15454 SDH TL1 Command Guide, R6.0
20-1
Chapter 20
RST Commands
20.1 RST-<MOD2>
Related Commands
DLT-<MOD1PAYLOAD>
RLS-PROTNSW-<STM_TYPE>
DLT-FFP-<MOD2DWDMPAYLOAD>
RMV-<MOD2>
DLT-FFP-<STM_TYPE>
RTRV-<MOD1FCPAYLOAD>
ED-<MOD1FCPAYLOAD>
RTRV-<MOD1FICONPAYLOAD>
ED-<MOD1FICONPAYLOAD>
RTRV-<MOD2DWDMPAYLOAD>
ED-<MOD2DWDMPAYLOAD>
RTRV-<STM_TYPE>
ED-<STM_TYPE>
RTRV-10GIGE
ED-ALS
RTRV-ALMTH-<MOD2>
ED-DS3I
RTRV-ALS
ED-E1/ED-E3/ED-E4
RTRV-DS3I
ED-FAC
RTRV-E1/RTRV-E3/RTRV-E4
ED-FFP-<MOD2DWDMPAYLOAD>
RTRV-FAC
ED-FFP-<STM_TYPE>
RTRV-FFP-<MOD2DWDMPAYLOAD>
ED-FSTE
RTRV-FFP-<STM_TYPE>
ED-G1000
RTRV-FSTE
ED-GFP
RTRV-G1000
ED-HDLC
RTRV-GFP
ED-STM1E
RTRV-GIGE
ENT-<MOD1PAYLOAD>
RTRV-HDLC
ENT-FFP-<MOD2DWDMPAYLOAD>
RTRV-PM-<MOD2>
ENT-FFP-<STM_TYPE>
RTRV-PMSCHED-<MOD2>
INIT-REG-<MOD2>
RTRV-POS
OPR-ALS
RTRV-PROTNSW-<MOD2DWDMPAYLOAD>
OPR-LPBK-<MOD2>
RTRV-PROTNSW-<STM_TYPE>
OPR-PROTNSW-<MOD2DWDMPAYLOAD>
RTRV-STM1E
OPR-PROTNSW-<STM_TYPE>
RTRV-TH-<MOD2>
REPT PM <MOD2>
SCHED-PMREPT-<MOD2>
RLS-LPBK-<MOD2>
SET-ALMTH-<MOD2>
RLS-PROTNSW-<MOD2DWDMPAYLOAD>
SET-TH-<MOD2>
Input Format
RST-<MOD2>:[<TID>]:<AID>:<CTAG>::::[<PST>[,<SST>]];
Input Example
RST-E1:CISCO:FAC-1-1:1::::UNLOCKED,AUTOMATICINSERVICE;
Cisco ONS 15454 SDH TL1 Command Guide, R6.0
20-2
Chapter 20
RST Commands
20.2 RST-EQPT
Input Parameters
Table 20-1
RST-<MOD2> Input Parameters
Parameter and Values
Description
AID
Access identifier from the “25.1 ALL” section on page 25-1
PST
Primary state
Parameter type is PST—indicates the current overall service
condition of an entity
•
Unlocked
In service
•
Locked
Out of service
SST
Secondary state
Parameter type is SST—provides additional information
pertaining to PST and PSTQ
•
AutomaticInService
Automatic in service
•
Disabled
Disabled
•
Loopback
Loopback
•
MismatchofEquipmentAlarm
Mismatch of equipment and attributes
•
Maintenance
Maintenance mode
•
OutOfGroup
Out of group
•
SoftwareDownload
Software downloading
•
Unassigned
Unassigned
•
NotInstalled
Unequipped
20.2 RST-EQPT
Restore Equipment
Usage Guidelines
Note
This command provisions equipment into the In Service state from the Maintenance state.
Only applicable to equipment that is in transition from the Maintenance state to the In-Service state.
Category
Equipment
Security
Maintenance
Cisco ONS 15454 SDH TL1 Command Guide, R6.0
20-3
Chapter 20
RST Commands
20.2 RST-EQPT
Related Commands
ALW-SWDX-EQPT
REPT RMV EQPT
ALW-SWTOPROTN-EQPT
REPT RST EQPT
ALW-SWTOWKG-EQPT
RMV-EQPT
CHG-EQPT
RTRV-ALM-EQPT
DLT-EQPT
RTRV-ALMTH-EQPT
ED-EQPT
RTRV-COND-EQPT
ENT-EQPT
RTRV-EQPT
INH-SWDX-EQPT
SET-ALMTH-EQPT
INH-SWTOPROTN-EQPT
SW-DX-EQPT
INH-SWTOWKG-EQPT
SW-TOPROTN-EQPT
REPT ALM EQPT
SW-TOWKG-EQPT
REPT EVT EQPT
Input Format
RST-EQPT:[<TID>]:<AID>:<CTAG>[::];
Input Example
RST-EQPT:CISCO:SLOT-1:1;
Input Parameters
Table 20-2
RST-EQPT Input Parameters
Parameter and Values
Description
AID
Access identifier from the “25.1.10 EQPT” section on page 25-15
Cisco ONS 15454 SDH TL1 Command Guide, R6.0
20-4