STANDARD DETAILS FOR METAL ROOFING AND SIDING AGRICULTURAL LIGHT COMMERCIAL RESIDENTIAL THE BLUE BOOK Due to Product improvements, changes and other factors, Fabral reserves the right to change or delete information herein without prior notice or obligation to make changes in products previously purchased. The details and written instructions described in this manual are suggested installation methods to ensure a quality application of our products, and should be considered as a guideline only. FABRAL recognizes that installation techniques can vary based upon builder and geographical preferences, and that there are other acceptable ways to install our products. Fabral.com / 800.477.2741 TABLE OF CONTENTS Introduction....................................................................2 Fabral Core....................................................................3 Installation Instructions..................................................4-5 Steel Panel Profiles........................................................6-8 Aluminum Panel Profiles................................................9 Estimating & Roof Types................................................10 Load Tables & Testing....................................................11 Building Details Post Frame.................................................................... 12 Residential..................................................................... 13 Post Frame Flashing Details Endlap & Rain Carrying Table............................................... 14 Flashings/Trim Post Frame.................................................................... 15-18 Residential..................................................................... 19 Mighti-Rib.................................................................20 General Notes................................................................21 System Components......................................................22-23 Accessories....................................................................24-25 Trim Details Post Frame Eave & Box Eave...................................................................26 Vented Eave & Endwall.........................................................27 Endwall- Notched & Sidewall................................................28 Dormer Valley & Valley..........................................................29 Gambrel & Transition............................................................30 Box Gable..............................................................................31 Gables...................................................................................32 Flying Gable Detail & Monoslope Ridge..............................33 Ridge/Peak- Non Vented & Vented Ridge............................34 Alternate Vented Ridge & Base Guard.................................35 Door Header & Door Jamb...................................................36 Door Jambs...........................................................................37 Overhead Door Jambs..........................................................38 Sliding Door Jamb, Header & Base......................................39 Window Sill, Header & Jamb & Translucent Panel...............40 Inside Corner & Outside Corners.........................................41 Residential Vented Eave & Eave............................................................42 Endwall & Sidewall................................................................43 Valley & Dormer Valley..........................................................44 Gambrel & Transition............................................................45 Pipe Boot & Skylight.............................................................46 Skylight Section A-A & B-B...................................................47 Chimney Details....................................................................48 Chimney Endwall & Ridge/Hip..............................................49 Vented Ridge & Gable..........................................................50 Paint System & Warranties............................................51 INTRODUCTION The Right Tools. This Standard Details Manual, AKA the Blue Book, is the right tool to have at your fingertips. By knowing you have access to all of the right information from proper storage and installation instructions to trim and flashing details, you can be confident installing your Fabral materials. In addition, the Blue Book references the complete system components and accessories allowing you plan ahead. Use the Blue Book, and call the Fabral CORE at 800.477.2741 when further support is needed. AGRICULTURAL Fabral is the solution for your agricultural applications. We know that your barns and buildings must stand up to all weather conditions and last through the years. LIGHT COMMERCIAL For your light commercial needs, Fabral offers metal roofing and siding to match the various building types. RESIDENTIAL Homeowners feel proud and confident with Fabral metal roofing for the durability and sophisticated appearance. 2 Fabral.com / 800.477.2741 You challenge us. And we like it. Your vision for a building and what you want to achieve makes us think harder. ItвЂ™d be easy to say - вЂњThat wonвЂ™t work.вЂќ Instead we go with - вЂњLetвЂ™s see what we can do.вЂќ As the leading provider of metal for building envelope solutions, we push the envelope. We like it when you bring us a problem because we know weвЂ™ll find the solution. We have the products, the manufacturing and the know-how. We offer everything you need for the total building envelope solution. At our core, we relish a challenge. CUSTOMER CARE SYSTEM SUPPORT EDUCATION PROJECT CONSULTING TECHNICAL SUPPORT To learn more contact us at 800.477.2741 or Fabral.com. 3 INSTALLATION INSTRUCTIONS Building Design and Construction In order to ensure the anticipated performance and longevity, protect metal panels from potentially corrosive situations and materials. When treated lumber will be in direct contact with metal panels or flashings please note the following: Galvanized steel is compatible with the CCA (Chromated Copper Arsenate) pressure-treated lumber that was predominantly used before 2004, but not with the older Penta treated lumber or the new ACQ (Alkaline Copper Quartenary), CA (Copper Azole), or CBA (Copper Boron Azole). Stainless steel or other special treated fasteners should be used into these non-compatible pressure treated lumbers. Aluminum must be separated from contact with all treated wood since the soluble copper in the preservative is corrosive to aluminum. Likewise, dissimilar metals also require a protective barrier between them to prevent galvanic corrosion. Request FABRAL Technical Bulletins #803, 106, and 107 for more information on treated lumber and dissimilar metals. Plastic, buildersвЂ™ felt, bituminous paint, caulking, or gasket material may be used to separate panels from treated wood and dissimilar metals. When using aluminum panels in direct contact with steel, use a separator as described above and fasten with Stainless Steel screws. Fertilizer, lime, acids, feeds, manure, soils, and many other compounds also cause corrosion in metal panels. Contact between metal panels and any potentially corrosive materials should be prevented. Porous insulation materials may absorb and retain moisture, and should not be used in direct contact with metal panels. Use a vapor barrier such as polyethylene plastic or 30-lb felt to prevent moisture from contacting both the insulation and the metal panel. FABRALвЂ™s translucent panels are intended for siding applications only. In all situations, foot traffic should be avoided on translucent panels. Translucent panels used in roofing applications will break down in a short time and cause staining and premature corrosion of the metal panels below. If used on roofs, apply butyl caulking to separate the fiberglass panels from the metal. Translucent panels should be cleaned and sealed regularly, as recommended by the translucent panel manufacturer. Purlins, Girts and Roof Deck The substructure to which the metal panels are fastened must be properly spaced and sufficiently thick to provide a roof or wall system able to meet required design loads. A 2вЂќ nominal lumber thickness or 1вЂќ nominal thickness are both acceptable purlins. If snow guards are to be installed in the future, a 2 x 8 purlin can be installed in the area for snow guard installation. Call engineering for locations of 2 x 8 purlins. When using purlins, FABRAL recommends a maximum spacing of 24вЂќ on-center (note that 5V requires solid decking). Pullout values decrease if the fasteners protrude completely through the purlins. Kiln-dried softwood is recommended for purlins or decking (pine, fir, hemlock, and spruce). Hardwoods are difficult to fasten into without splitting and contain tannic acids that are corrosive to metal panels. Green (non-kiln-dried) lumber may warp, twist, and shrink as the wood seasons fully, causing waviness in the panels as well as loosening and leaking of the fasteners. Solid decking is highly recommended for all residential applications. When using solid decking or sheathing, always use 30-lb felt or underlayment and plan on using closer fastener spacing and larger diameter #14 screws. (Refer to the tables on page 31). On re-roofing projects where the condition of the old decking is in question, or where existing shingles will be left in place, new 2x4 or 1x4 purlins should be fastened through the decking and into the rafters. This will provide a solid framework for attaching the metal panels. For more detailed information on re-roofing applications, consult FABRAL Technical Bulletin #721, Re-Roofing With Metal. Load tables are available for all FABRAL panels; contact FABRAL for additional information. Roofing Panel sidelaps should face away from wind driven rain. To accomplish this, begin by installing the first sheet square with the eave and gable at the down wind end of the roof, farthest away from the source of prevailing winds or away from the primary viewing location. In applications requiring a panel endlap, please refer to the detailed instructions in this booklet. For best results, lap panels as shown and install in the indicated sequence. All endlaps require sealant. When weather-tightness is critical, use sealant tape in all sidelaps. To provide a drip edge, allow an overhang of 1 to 2 inches at the eave. At the gable edge, use a gable or sidewall flashing. This will keep weather out, prevent lifting in high winds, and provide a neat, finished appearance. The trim and roofing sheet should be fastened every 12 to 24 inches along the gable edge. Do not step on panel ribs or on trim pieces to prevent kinking. Roof Pitch The metal roofing panels shown in this manual require a minimum slope of 2ВЅвЂќ per foot to ensure proper drainage. Refer to the rain-carrying table in this booklet for the maximum allowable panel length per slope that will provide adequate drainage. For longer slopes and lower roof pitches, contact FABRAL for other suitable profiles. Bending and Bowing Aluminum and Steel roofing and siding sheets are rollformed from hardened, tempered metal for maximum strength. If a sheet must be bent, a gentle 90-degree bend is the maximum recommended. Metal should not be re-bent once it has been formed, nor should it be folded back on itself. When a metal roofing sheet must be installed on a curved roof, screws should be installed at every overlapping rib at the sheet ends to resist the natural tendency of the metal to spring back. The standard fastening pattern is permitted over the rest of the sheet. When installing the metal panels shown in this booklet over a curved arch, the minimum radius of the arch is 18вЂ™ for aluminum panels and 24вЂ™ for steel panels. Use sealant tape or butyl caulking at all sidelaps and endlaps. Additional care and fasteners must be provided when securing the top and bottom purlins on an arched rafter building to prevent the curved panels from pulling the purlins loose from the rafters. Ring-shank pole barn nails, heavy wood screws, lag screws, or bolts are often used for attaching these purlins. Siding Siding should be installed using the standard fastening and overlap patterns to ensure optimum performance. For strong, neat corners use hemmed corner flashings. Do not run siding sheets all the way to the ground. Instead, provide a protective base of concrete, masonry, treated wood, or similar material and terminate the siding sheets 6вЂќ above grade. If siding sheets are installed horizontally, use sealant tape or butyl caulking at the vertical laps to ensure weather-tight joints. Install panels from the bottom up so that water is directed away from, and not into, the lap joints. Fastening FABRAL can supply either screws or nails for fastening into dimension lumber. Always use screws with solid sheathing. Screws for use with steel panels are galvanized and then coated with an organic polymer for optimum corrosion resistance. For best results with aluminum panels, use #300 series stainless steel screws. The FabrOsealВ® galvanized ring-shank nail, with its premium long-life silicone rubber gasket, assures a lasting seal and is the best nail available for steel panels when screws are not the method being used by the installer. The correct way to fasten steel panels with nails is to drive the nail through the top of the rib so the washer is compressed securely against the metal. Nail placement must be in the ribs for roofing applications to minimize the potential for roof leaks. Over-driving the nail can split the washer and dimple the metal, causing leaks. Correct Under-Driven Over-Driven Wood screws with combination metal and neoprene washers should be installed in the flat area of the panel adjacent to the ribs, and tightened such that the washer is compressed as illustrated above. This will ensure a lasting, leak-proof seal. Remove any metal filings created by the drilling action of the screws or pre-drilling of the holes to avoid rust staining on the panel surface. Refer to the fastening schedules in this booklet for the correct fastener locations. Flashing and Trim Always begin flashing installation from the bottom and work up, so that upper flashings are lapped on top of lower flashings. This will prevent moisture from leaking under the flashings and into the structure. Endlap flashings a minimum of 6вЂќ and seal the lap joints with sealant. Extend flashings 4-6вЂќ beyond the building, cut along the bend lines, apply sealant, and fold the side flaps in and the top flaps down to cap off the ends. Secure with pop-rivets or stitch screws. Some roof conditions, such as valleys, may require a longer endlap and/or a larger flashing to properly drain moisture from the roof. Factors that influence flashing size, shape, and endlap requirements include roof pitch, roof geometry, slope length, and climatic factors (such as heavy snowfall or rainfall). Whenever possible, begin trim installation at the downwind end of the roof, farthest away from the source of prevailing winds, to allow flashing laps to face away from wind-driven rain. Refer to the details in this book for the proper location of fasteners and sealants. The flashings and trims shown in this book are standard parts. Custom trims are available to meet your specific design needs. If you need a special trim, please furnish a drawing of the desired shape, including dimensions and angles, to your Fabral dealer to obtain pricing and availability. Refer to the SMACNA Architectural Sheet Metal Manual for additional information about detailing and installing flashings. Safety Always work safely when installing metal products and use extreme caution on the roof at all times. Wear gloves and safety glasses to reduce the risk of injury, and use hearing protection when operating power tools. Always be sure that ladders are safely positioned and properly secured. Safety harnesses or other special equipment may be required; be sure to Consult OSHA guidelines for compliance with all safety requirements. Do Not walk on panels until all the fasteners are installed. Metal roofing panels are slippery when wet, dusty, frosty, or oily -- Do Not attempt to walk on a metal roof under these conditions. Wear soft-soled shoes to improve traction and to minimize damage to the paint finish. Always be aware of your position on the roof relative to any roof openings, roof edges, co-workers, and penetrations. Installing metal panels or flashings on a windy day can be dangerous and should be avoided if possible. Cutting Aluminum Panels To make a cut parallel to the ribs, score the panel deeply with a sharp utility knife and bend back-and-forth along the score, breaking the metal off cleanly. For cuts across the ribs, use straight-cut snips, electric or pneumatic shears, a portable profile shear, or an electric nibbler. Some installers prefer using a circular saw with a metal cutting blade (a fine-tooth hardwood blade, or a standard combination blade reversed in the saw works also). Light oil or soap on the blade will make cutting easier. Cutting and Drilling Steel Panels Steel panels may be cut with metal snips, electric or pneumatic shears, a portable profile shear, or an electric nibbler. Some installers prefer using a circular saw to cut metal panels. Do Not use self-consuming abrasive blades because of the following: 1. Abrasive blades burn the paint and galvanizing at the cut edge, leaving edges that are jagged and unsightly and rust more quickly 2. Abrasive blades produce hot metal filings that embed in the paint and cause rust marks on the face of the panel. If saw cutting cannot be avoided, select a carbide-tipped blade specially designed for cutting light-gage ferrous metal panels. These blades are now available at many home centers and lumber yards. 1. All saw cut panels must be turned face down and cut in a location down-wind and well away from the building and other panels to avoid embedment of metal filings on other panels 2. All saw cut panels must be thoroughly wiped to ensure the removal of all metal filings. Pre-drilling wall panels gives uniform alignment of screw rows. Be sure to remove any filings once panels are installed to avoid rust marks from the filings. Building Maintenance A metal roof should be inspected annually and cleaned as necessary to maintain its beauty and performance. Any debris or residue, including leaves, twigs, and dust should be cleaned off promptly to prevent moisture entrapment against the metal, which may lead to finish deterioration or premature corrosion. Flashings may need to be re-sealed periodically in order to maintain optimum weathertightness. Proper Storage Store metal panels indoors when possible; if outdoors, cover and elevate. Elevate one side higher for water drainage. Never cover in plastic; us a tarp that can breath. Allow for air circulation. If a bundle gets wet, break bands and separate sheets; allow sheets to dry completely and only restack if completely dry. Product should be stored for a maximum of 2-4 weeks before being installed. Spray Foam Insulation When insulating metal with spray foam insulation, the first application layer should be getting the insulation behind all framing members. When completing the insulation, ensure the spray foam is installed in 2вЂќ thick layers (maximum) until desired thickness is achieved. STEEL PANELS Grandrib 3 В® 29 Gauge Steel, Plain and Painted Galvanized 3/4"Formed Formed Width 37 37 3/4вЂќ Width 36" Coverage 36вЂќ Coverage 9" 9вЂќ 3/4" 3/4вЂќ SCREW PATTERNS Intermediate Roof Purlins and All Siding NAIL PATTERNS All Supports Eaves and Endlaps - Roof Purlins 80 screws per square or 1 pound of nails per square See page 11 for a load table MP Panelв„ў NAIL PATTERNS All Supports SCREW PATTERNS 3/4" Formed Width 37 3/4вЂќ37Formed Width 36" Coverage 36вЂќ Coverage 9" 9вЂќ Intermediate Roof Purlins and All Siding Eaves and Endlaps - Roof Purlins 3/4" 3/4вЂќ *Not all profiles are available in all areas. Please contact Fabral for availability 6 Fabral.com / 800.477.2741 STEEL PANELS NAIL PATTERN Mighti-Rib В® SCREW PATTERN ROOFING - EAVES, RIDGES AND ENDLAPS 39вЂќ Formed Width 36вЂќ Coverage ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS Purlin Bearing Leg 12вЂќ 1 1/4вЂќ Please see Mighti-Rib specific trims on page 20 5V Crimp NAIL PATTERN USE ON SOLID DECKING ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - INTERMEDIATE SUPPORTS 26"Formed Formed Width 26вЂќ Width 24" Coverage 24вЂќ Coverage 1/2вЂќ 1/2" 1вЂќ 1" 1вЂќ 1" SCREW PATTERN 12" 12вЂќ 1/2вЂќ 1/2" ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS ProClad Sidelap Detail SCREW PATTERNS Intermediate Roof Purlins and All Siding 36вЂќ Coverage 9вЂќ Eaves and Endlaps - Roof Purlins 5/8вЂќ 1 1/4вЂќ Corrugated 26вЂќ Formed Width 24вЂќ Coverage 1 1/4вЂќ SCREW PATTERN 1/4вЂќ 2 1/2вЂќ Corrugated NAIL PATTERN ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS SCREW PATTERN ROOFING - EAVES, RIDGES, AND ENDLAPS NAIL PATTERN ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - INTERMEDIATE SUPPORTS ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS 26вЂќ Formed Width 24вЂќ Coverage SIDING - ALL SUPPORTS 2 1/2вЂќ 1/2вЂќ *Not all profiles are available in all areas. Please contact Fabral for availability 7 STEEL PANELS Prime RibВ® 38" Formed Width 36" Coverage 1" 3" 1" 1/2" GrandbeamВ® 1" Formed Width 424 36" Coverage 9" 1 2" 7" 8 4" 9" 416 100В° 3" 18 Note: Grandbeam has panel specific flashings available 134В° 134В° StrongCladВ® 36вЂќ 5/8вЂќ 9вЂќ *Not all profiles are available in all areas. Please contact Fabral for availability 8 Fabral.com / 800.477.2741 ALUMINUM PANELS Grandrib 3 В® ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS 3/4" Formed Width 37 3/4вЂќ37Formed Width 36" Coverage 36вЂќ Coverage 9" 9вЂќ 3/4" 3/4вЂќ Strongrib В® .018 Aluminum, Plain and Painted White SCREW PATTERN Correct Strongrib Sidelap BUTYL SEALANT LOCATION (OPTIONAL FIELD APPLIED) PURLIN BEARING LEG 3/4вЂќ 9вЂќ 36вЂќ Coverage (37 3/4вЂќ Formed Width) INTERMEDIATE ROOF PURLINS AND ALL SIDING EAVE AND ENDLAPS - ROOF PURLINS 2 1/2вЂќ Fabrib В® ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS 51 3/16вЂќ Overall 2 2/3вЂќ 3/4вЂќ 48вЂќ Coverage AluTwin Other widths available 50 1/4вЂќ Overall 48вЂќ Coverage 8вЂќ 2 1/2вЂќ Corrugated 26вЂќ Formed Width 24вЂќ Coverage 2 1/2вЂќ 7/16вЂќ 1/2вЂќ ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - EAVES, RIDGES, AND ENDLAPS ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS ROOFING - INTERMEDIATE SUPPORTS SIDING - ALL SUPPORTS *Not all profiles are available in all areas. Please contact Fabral for availability 9 ESTIMATING & ROOF TYPES Estimating Metal Roofing, Siding & Flashings Panel lengths are to be determined by the truss top chord or actual field measurements. Remember to add for overhangs at the eaves; subtract for a gap at the ridge. Siding should be kept up away from the ground with a skirt board. Number of Panels The coverage of the panel being used will determine the number of panels at a length (i.e.: 3вЂ™ coverage panel on a 30 ft. long building would require 10 panels on each side of the ridge or 20 panels at the particular length.) Gambrel Roof Horizontal Measurement to a Roof Divide the building width in half, then multiply by the slope factor (i.e.: 40вЂ™ wide building with 4/12 slope. 40 divided by 2 equals 20вЂ™ times 1.054 equals 21вЂ™-1вЂќ in slope dimension.) Allow for 1/2вЂќ to 1вЂќ gap at peak and 1вЂќ to 2вЂќ eave overhang. Roof Pitch Slope Factor 3/12 4/12 5/12 6/12 8/12 10/12 12/12 1.031 1.054 1.083 1.120 1.202 1.302 1.414 Transition Roof Flashing Conditions Roof - Eave, Ridge, Gable, Sidewall, Endwall, Valley, Hip, Transition, Gambrel, Soffits Siding - Base Perimeter, Corners, Inside Corners, Man Doors, Windows, Sliding Doors, Overhead Doors Please contact FabralвЂ™s Engineering Department for all your estimating & specification needs. 800.477.2741 717.735.1257 Fax 10 Fabral.com / 800.477.2741 Hip Roof LOAD TABLES & TESTING GRANDRIB 3 Load-Span Tables For 29 Gauge Grandrib 3 Allowable Wind Uplift Loads (psf) Spacing of Fastener Rows Substrate 3/4" Plywood 5/8" Plywood 1/2" Plywood 23/32" OSB 19/32" OSB 7/16" OSB Solid 2x SPF Solid 1x Pine Solid 2x SPF Solid 1x Pine Fastener #14 Woodtite #14 Woodtite #14 Woodtite #14 Woodtite #14 Woodtite #14 Woodtite #14 Woodtite #14 Woodtite #9 WoodFast #9 WoodFast Screws per Square 9" 275.6 12" 206.7 15" 165.4 18" 137.8 21" 118.1 24" 103.4 160 135.9 115.9 120 101.9 86.9 96 81.5 69.5 80 67.9 57.9 68.6 58.2 49.7 60 51.0 43.5 100.7 75.5 60.4 50.3 43.1 37.8 61.5 293 207.1 46.1 220.0 155.3 36.9 176.0 124.2 30.7 146.7 103.5 26.3 125.7 88.7 23.1 110.0 77.7 218.7 164.0 131.2 109.3 93.7 168.4 126.3 101.0 84.2 72.2 82.0 63.2 190 150 120 100 90 80 T he Above L oads and fas tener quantities are bas ed on the s tandard fas tening s chedule s hown on page 6 of this book, with the fas tener having an embedment depth of 1" into the s olid wood and penetrating the plywood or OS B . C ontact F AB R AL for additional des ign information on our products . UL RATINGS UL790 Class A Fire Rating applies to all Steel panels 29 ga and thicker and all Aluminum panels .032вЂќ and thicker. UL2218 Class 4 Hail Impact Rating applies to all Steel panels 29 ga and thicker and all Aluminum panels .032вЂќ and thicker. 11 12 Fabral.com / 800.477.2741 Zee p. 18 Base Guard p. 35 Drip Cap p. 36 J-Channel/ Doors/Windows p. 36 Gable p. 31 Endwall p. 27 Inside Corner p. 41 Ridge/Peak p. 34 BUILDING DETAILS POST FRAME Sidewall p. 28 Sliding Door Track Cover p. 39 Outside Corner p. 41 Eave p. 26 RIDGE/PEAK CHIMNEY VALLEY ENDWALL PIPE PENETRATION TRANSITION SIDEWALL EAVE SKYLIGHT GABLE/RAKE HIP RESIDENTIAL exposed-fastener panel BUILDING DETAILS 1. Determine the thickness and type of substrate to be used to support the metal roofing. Solid decking is highly recommended for all residential applications (i.e., plywood, OSB). 2. Refer to the Load-Span tables to select the proper fastener and spacing to meet loads on your structure. Nails are NOT recommended for residential applications. 3. Consult local building codes and restrictions to determine acceptable methods of construction for residential applications in your area. 4. Solid decking with 30# felt or synthetic underlayment for residential applications is recommended. Ice & water shield or similar self-adhesive membrane is recommended at all valleys, dormers, chimneys, transitions, skylights and other critical areas. 5. When re-roofing with metal panels over an existing shingle roof, metal panels may be installed directly over shingles with underlayment, or 2x4 purlins or 1x4 furring strips. 6. Zip board sheathing, which has a вЂњbuilt inвЂќ vapor barrier, is an acceptable substrate and vapor barrier. 7. Request FabralвЂ™s technical bulletins # 720 and # 721 for more details on residential roofing. 13 POST FRAME FLASHING DETAILS ENDLAP & RAIN CARRYING TABLES 1. Apply 3/32вЂќ x 1/2вЂќ butyl endlap sealant on bottom panel just below centerline of purlin (see endlap diagram for location) on panel #1. 2. Apply sidelap sealant on panel #1 and connect to endlap sealant. 3. Place panel #2 so it overlaps panel #1, 12вЂќ as shown. Install screws per endlap fastening pattern. 4. Apply sidelap sealant on panel #2 to connect to sidelap sealant of panel #1. 5. Place panel #3 over sidelap of #1 and #2. 6. Apply endlap sealant on panel #3. 7. Apply sidelap sealant on panel #3 and connect with endlap sealant. 8. Place panel #4 over endlap of panel #3. Install screws per endlap pattern. 9. Repeat sequence for entire roof. D ALUMINUM ROOF PANEL STEP #1 CONTINUOUS BEAD OF 3/32" x 1/2" BUTYL SEALANT TAPE DOWN SLOPE STEEL STEP #2 3 1/2" 10" To Sealant FASTENERS @ ENDLAP PATTERN ROOF PANEL DOWN SLOPE 6 1/2" 2" OVERLAPPING FROM PURLIN EDGE PR EV ENDLAP TAPE ALIGN WITH PURLIN EDGE 5 1 4 2 WHEN INSTALLING 2 1/2" OR 1 1/4" CORRUGATED ROOFING USE INSTALLATION SEQUENCE AS SHOWN Panel Name Panel Alu-Tuff Name EAVE OVERHANG 1" TO 2" (IN "L" ST AR TE ND ALLOWABLE PANEL LENGTHS (ft.) ALONG THE SLOPE FOR 4" RAINFALL HOUR ALLOWABLE PANEL LENGTHS PER (ft.) ALONG Roof Slope THE SLOPE FOR 4" RAINFALL PER HOUR Minimum Slope 2 1/2:12 3:12 Roof Slope 3 1/2:12 4:12 5:12 6:12 58 2 1/2:12 Minimum Slope 2 1/2:12 61 3:12 64 3 1/2:12 67 4:12 73 5:12 78 6:12 Grandrib Alu-Tuff 3 2 1/2:12 58 61 64 67 73 78 Prime Rib3 Grandrib 2 1/2:12 39 58 41 61 43 64 45 67 49 73 53 78 5V Prime Rib 2 1/2:12 43 39 45 41 47 43 49 45 54 49 58 53 5V 2 1/2" Corrugated 2 1/2:12 28 43 29 45 31 47 32 49 35 54 38 58 1 1/2" 1/4" Corrugated 2 2 1/2:12 16 28 16 29 17 31 18 32 20 35 21 38 Alutwin 1 1/4" Corrugated 2 1/2:12 37 16 39 16 41 17 43 18 46 20 50 21 Fabrib Alutwin 2 1/2:12 32 37 34 39 36 41 38 43 41 46 44 50 Fabrib 32 Rain-Carrying 34 36 Tables 38 44 2 1/2:12 41 Notes For 1. All values based on a 1-hour duration storm of 4"/hr. intensity. Notes For 2. Values represent the point at which theRain-Carrying panel ribs will flood. Tables 1. values based on of a 1-hour duration storm of 4"/hr. intensity. 3. All Size and frequency penetrations can greatly reduce the amount of water removed from a rooof. 2. represent point at which the panel ribs will flood. 4. Values All panel endlaps the must be caulked. 3. Size and frequency of penetrations can greatly reduce thesidelaps. amount of water removed from a rooof. 5. When weather-tightness is crtical, use sealant tape in all 4. All panel endlaps must be caulked. 5. When weather-tightness is crtical, use sealant tape in all sidelaps. 14 Fabral.com / 800.477.2741 ) ET SKIRT BOARD OF TREATED LUMBER OR FOUNDATION OF BLOCK 12" TO 18" FROM GROUND LEVEL WI ND SIDELAP TAP THIS EDG 3 3 1 ING END 2 5 AIL 4 SIDELAP TAPE THIS EDGE SIDELAP TAPE THIS EDGE PURLIN 3 1/2" 12" Total Lap INSTALLATION SEQUENCE FOR STRONGRIB, GRANDRIB 3, 5V CRIMP, ALU-TWIN ENDLAP TAPE THIS EDGE 6 1/2" 2" OVERLAPPING FROM PURLIN EDGE FE STANDARD POST FRAME FLASHINGS & TRIMS All flashing is 10вЂ™ 6вЂќ in length & available in steel & aluminum, unless otherwise noted. Please contact Fabral for specifics on the trim available in your area. AJ2 Jamb Trim AJ3 J Channel AJ4 Jamb Trim AJ6 Jamb Trim AJ5 Jamb Trim #45 Liner Channel F-J Trim RJ8 J Channel PJFB One Piece Door Trim RJ9 F-J Trim 15 POST FRAME FLASHINGS & TRIMS AG4 Gable AC1 Corner Longer Lengths Available AG1 Gable/Rake Longer Lengths Available AC3 Corner Longer Lengths Available AC2 Inside Corner AC4 Corner Longer Lengths Available RG1 Residential Gable WG1 Residential Gable Longer Lengths Available AH3 Double Door Track Cover 16 AH2 Door Track Cover Longer Lengths Available AH4 Door Track Cover Fabral.com / 800.477.2741 AH5 Door Track Cover POST FRAME FLASHINGS & TRIMS AH6 Door Track Cover RR1 Universal Ridge/Hip Flash AR3 Ridge Cap CP1 Monoslope Ridge AR3 w/ Versavent RX-10 Ridge Cap SB Snow Break AT1 Transition Flash CE1 Denver Eave AT2 Gambrel Flash ASW1 Sidewall/Endwall Flash AEWN4 Notched Endwall Flash AGRN4 Notched Gambrel Flash Notched 17 POST FRAME FLASHINGS & TRIMS *Other sizes are available upon request AL6 Angle Flashing AL2, 3, 4, 5 Angle Flashing AL7 Angle Flashing Longer Lengths Available AL9 Angle Flashing AL8 Angle Flashing ABG1 Base Guard AL10 Angle Flashing 203 Box Base AB1 Soffit Box AZ2 Zee AB3 Soffit Box AD1 Drip Cap 7 1/2" AB2 Soffit Box 7 1/4" AB4 Soffit Box 2 1/2" RV1 Valley Flash AE1 Eave Flash RV2 W-Valley Flash 18 RE1 Residential Eave Fabral.com / 800.477.2741 STANDARD RESIDENTIAL exposed-fastener panel FLASHINGS & TRIMS All flashing is 10вЂ™ 6вЂќ in length & available in steel & aluminum, unless otherwise noted. Please contact Fabral for specifics on the trim available in your area. RG1 Residential Gable CE1 Denver Eave AR3 Ridge Cap RR1 Universal Ridge/Hip Flash RE1 Residential Eave ASW1 Sidewall/ Endwall Flash AG4 Gable WG1 Residential Gable RV1 Valley Flash RV2 W-Valley Flash AT1 Transition Flash CP1 Monoslope Ridge AT2 Gambrel Flash 19 POST FRAME FLASHINGS & TRIMS STANDARD MIGHTI-RIBВ® FLASHINGS & TRIMS All Mighti-Rib specific flashing is 10вЂ™ 6вЂќ in length & available in steel, unless otherwise noted. Please contact Fabral for specifics on the trim available in your area. FH1 Head/Sill Flashing FR4 Ridge Cap FE2 Eave Flashing FT1 Endwall/ Transition Flash FC4 Inside Corner Flash FC3 Gable/Outside Corner Flash FJ4 Zee Flash FJ3 J Channel Flashing 20 Fabral.com / 800.477.2741 GENERAL NOTES 21 SYSTEM COMPONENTS SNOW GUARDS Exposed Fastener Panel Grandrib 3В® Mighti-RibВ® MP Panelв„ў 5V Crimp 2 1/2вЂќ Corrugated ProClad MINI CL #640 X X X X X X X X X X X X X X X X SM X X X MINI Clear Snow Guard вЂў Available in premium polycarbonate plastic with UV stabilizers вЂў Provides maximum protection at a moderate price point вЂў Two-to-one base-to-blade ratio вЂў 4.5 sq.in. and gusseted blade snow pocket вЂў Typically installed by adhering to and mechanically fastened to the roofing panel Snow Boss Snow Guards (#640) вЂў вЂњTraditional ShapeвЂќ solid cast aluminum вЂў Applied to the mid-panel on all standing, batten and flat seam roofs вЂў Typically installed by adhering to and mechanically fastened to the roofing panel вЂў Low profile protection, ideal for 1вЂќ x 2вЂќ purlins вЂў Non-Stock item, inquire for lead time 22 #20 Fabral.com / 800.477.2741 X X CL Snow Guard вЂў Available in premium polycarbonate plastic with UV stabilizers вЂў Unique vent rib systems allows for adhesive out gassing вЂў Three-to-one base-to-blade ratio adds significantly to strength SM Snow Guard вЂў Available in cast aluminum вЂў Typically installed by adhering to and mechanically fastened to the roofing panel вЂў Very effective where there are no suitable seams вЂў Non-Stock item, inquire for lead time SYSTEM COMPONENTS FASTENERS For more information, review FabralвЂ™s installation manuals. #9-16 WoodFast #14-10 WoodTite вЂў Use with dimensional lumber вЂў Use to fasten metal to plywood or OSB вЂў Available in 1вЂќ, 1 1/2вЂќ, 2вЂќ, 2 1/2вЂќ and 3вЂќ вЂў Use for trim attachment вЂў 1/4вЂќ hex head, EPDM/metal washer вЂў Available in 1вЂќ, 1 1/2вЂќ, and 2вЂќ вЂў Oxyseal Long-Life Coating вЂў 5/16вЂќ hex head, EPDM/metal washer вЂў Plain or Painted вЂў Oxyseal Long-Life Coating вЂў 250/bag вЂў Plain or Painted вЂў 250/bag #9-16 300 Series Stainless Steel #10-14 410 Stainless Steel вЂў Use for high corrosive environments вЂў Use with 26 gauge or thinner to avoid pre-drilling вЂў Use with ALUMINUM panels вЂў NOT as corrosive resistant as the 300 Series вЂў Available in 1вЂќ, 1 1/2вЂќ, and 2вЂќ вЂў Steel is harder than 300 Series вЂў 1/4вЂќ hex head, EPDM/metal washer вЂў Available in 1вЂќ, 1 1/2вЂќ, and 2вЂќ вЂў Use with treated lumber вЂў 1/4вЂќ hex head, EPDM/metal washer вЂў Plain or Painted вЂў Use with steel panels installed on treated lumber вЂў 250/bag вЂў Plain or Painted вЂў 250/bag #10-16 Ultimate WoodTite #12 x 3/4вЂќ Stitch Screw вЂў Use with ALL panels вЂў вЂў Available in 1вЂќ, 1 1/2вЂќ, 2вЂќ, 2 1/2вЂќ and 3вЂќ вЂў 5/16вЂќ case zinc hex head вЂў Use with STEEL panels вЂў Hex head & washer all one piece вЂў Used to stitch sidelaps for exposed fastener panels вЂў Plain вЂў Used for miscellaneous metal to metal attachments вЂў 250/bag вЂў 1/4вЂќ hex head, EPDM/metal washer вЂў Plain or Painted вЂў 250/bag Used for attachment of trim to top of seam for screw flange panels UNDERLAYMENT 30-Year Peel & Stick PRODUCT SPECS: 50-Year Synthetic PRODUCT SPECS: 30-Year Synthetic PRODUCT SPECS: 25-Year Synthetic PRODUCT SPECS: вЂў Watertight Self-Sealing Under- вЂў Installation Requires вЂў Installation Requires вЂў Installation Requires layment mechanical fasteners mechanical fasteners mechanical fasteners вЂў Asphalt-to-Asphalt Lap System вЂў Roll Size: 4вЂ™ W x 250вЂ™ L вЂў Roll Size: 4вЂ™ W x 250вЂ™ L вЂў Roll Size: 4вЂ™ W x 250вЂ™ L вЂў Roll Size: 3вЂ™ W x 72вЂ™ L вЂў Minimum Thickness: .75mm вЂў Minimum Thickness: .63mm вЂў Minimum Thickness: .43mm вЂў Minimum Thickness: 1.1mm вЂў Square Ft Per Roll: 1,000 вЂў Square Ft Per Roll: 1,000 вЂў Square Ft Per Roll: 1,000 вЂў Square Ft Per Roll: 200 23 ACCESSORIES VENTING & CLOSURES Ridge Cap Vent Specifications: вЂў вЂў вЂў вЂў Venting factory applied to the ridge cap Save up to half of your installation time Non-profile specific material Clean, dust free installation Virtually NO WASTED material вЂў 1 1/2вЂќ x 3вЂќ material provides 17 sq. inches/lineal foot free area at the ridge Available attached to ridge cap as RX-10 version and as X-10 version for field installation; not pre-applied to ridge cap Profile Fit Vent-Strip Specifications: вЂў Available in Climaguard, Grandrib 3 and Mighti-Rib profiles вЂў Lower, custom-fit profile вЂў Moisture and pest barrier вЂў Non-obtrusive appearance вЂў Reduces utility costs вЂў One-person installation RV35 and RV100 Specifications: LP2 Closure Specifications: вЂў Available in Grandrib 3, Strongrib, 1 1/4вЂќ Corrugated, 2 1/2вЂќ Corrugated and 5V profiles вЂў 10.66 sq. in. per lineal ft. of ridge (5.33 / side) вЂў 10вЂ™ long metal ridge vent вЂў Variety of colors available Profile Fit Vent- Roll Specifications: вЂў Available in Grandrib 3 and 5V profiles вЂў 10.66 sq. in. per lineal ft. of ridge (5.33 / side) TRANSLUCENT PANELS 24 Fiberglass: Polycarbonate: вЂў Grandrib 3 - White, Green - 8вЂ™, 10вЂ™, 12вЂ™; Strongrib - White - 10вЂ™, 12вЂ™; Fabrib - Green - 12вЂ™ вЂў Grandrib 3- Clear & White - 8вЂ™, 10вЂ™, 12вЂ™ ; Mighti-Rib - Clear & White - 12вЂ™ Fabral.com / 800.477.2741 ACCESSORIES PIPE BOOTS EPDM Specifications: Pipe Sizes: вЂў Colors: gray and black вЂў Up to 2500 F Base Diameter 7 3/4вЂќ 10 3/4вЂќ 16 1/2вЂќ Item No. 3 5 8 min max 1/4вЂќ 5вЂќ 4 1/4вЂќ 7 1/2вЂќ 7вЂќ 13вЂќ Silicon Specifications: вЂў вЂў вЂў вЂў Color: orange Up to 4500 F Ranging for pipe sizes from 1вЂќ to 13вЂќ Larger sizes available on request FLAT SHEETS Product Specifications: вЂў Used for field forming crickets around chimney, skylights and penetrations, and special flashing as necessary вЂў 29 gauge painted and plain galvanized вЂў Full width (40вЂ™ 13/16вЂќ x 10вЂ™ 6вЂќ) вЂў Grade 33 steel for better hemming, forming and flexibility for field forming SEALANT & SEALER STRIP Sealant Specifications: Sealant Tape Specifications: вЂў вЂў вЂў вЂў вЂў вЂў 3/16вЂќ x 1/4вЂќ x 40вЂ™ (sidelap) вЂў 3/32вЂќ x 1/2вЂќ x 50вЂ™ (endlap) вЂў 1/8вЂќ x 2вЂќ x 30вЂ™ Waterproof sealant to fill gaps up to 1вЂќ UV-resistant Permanent flexibility - wonвЂ™t crack Standard color: gray (stocked) Up to 50 additional color options (non stocked) Asphalt Impregnated Sealer Strip Specifications: вЂў Use at valleys and hips вЂў 1вЂќ x 1вЂќ x 19вЂ™ 6.8вЂќ long 25 POST FRAME TRIM DETAILS INSIDE CLOSURE BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE FASTENER PER STANDARD EAVE PATTERN OUTSIDE CLOSURE (OPTIONAL) ROOF PANEL FLASH CE-1 BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE FASTENER @ EVERY MAJOR RIB SIDING PANEL ROOF PURLIN POST EAVE ROOF TRUSS TOP PLATE INSIDE CLOSURE 3. EAVE (PAGE 15) ROOF PANEL FASTENER PER STANDARD EAVE PATTERN FLASH CE-1 BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE EAVE PURLIN FLASH AB-1, AB-2, AB-3, OR AB-4 FASTENER FASTENER @ 24" O.C. MAX. OUTSIDE CLOSURE (OPTIONAL) SIDING PANEL BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE TOP PLATE BOX EAVE 26 Fabral.com / 800.477.2741 POST FRAME TRIM DETAILS INSIDE CLOSURE BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE FASTENER PER STANDARD EAVE PATTERN FABRAL ALUMINUM SOFIT ROOF PANEL TOP PLATE FLASH CE-1 FASTENER @ 24" O.C. MAX. F/J TRIM SIDING PANEL FASTENER VENTED EAVE 5. VENTED EAVE (PAGE 16) SIDING PANEL FASTENER PER STANDARD EAVE PATTERN GIRT INSIDE CLOSURE 2" FASTENER @ EVERY MAIN RIB FLASH ASW-1 BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE PURLIN ENDWALL ROOF PANEL OUSIDE CLOSURE 12. ENDWALL (PAGE 21) View installation videos at Fabral.com/videos 27 POST FRAME TRIM DETAILS ENDWALL- NOTCHED SIDING PANEL FASTENER PER STANDARD EAVE PATTERN GIRT INSIDE CLOSURE 2" FASTENER @ EVERY MAIN RIB NOTCHED FLASH AEW-N4 OR AEW-N5 BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE PURLIN ROOF PANEL OUSIDE CLOSURE 13. ENDWALL - NOTCHED (PAGE 21) SIDING PANEL SIDEWALL FASTENER PER STANDARD EAVE PATTERN GIRT SEALER STRIP W/ BUTYL SEALANT TAPE FLASH ASW-1 FIELD BEND AS REQUIRED 2" FASTENER @ 24" O.C. MAX. BUTYL SEALANT TAPE ROOF PANEL PURLIN SLOPING RAFTER ROOF PANEL 28 Fabral.com / 800.477.2741 POST FRAME TRIM DETAILS RIDGE TRIM DORMER VALLEY OUTSIDE CLOSURE, TAPE SEALANT TOP & BOTTOM ROOF PANEL UNIVERSAL CLOSURE, TAPE SEALANT TOP & BOTTOM LOWER VALLEY TRIM BUTYL TAPE SEALANT PEEL & STICK UNDERLAYMENT UPPER VALLEY TRIM VALLEY LARGER VALLEYS MAY BE REQUIRED FOR LONG ROOF PANEL RUNS OR HEAVY SNOW AREAS. CUT ROOF PANEL AS NECESSARY NOTE: ROOF PANEL OMITTED ON OTHER SIDE OF RIDGE FOR CLARITY. 39. DORMER VALLEYS (PAGE 43) RV-2 SHOWN SCREWS EACH SIDE OF MAIN RIB (EAVE / ENDLAP PATTERN) PEEL & STICK SEALER STRIP, 1" X 1" X 19'-8" BLOCK CLOSURE, FILL RIB VOIDS ROOF STRUCTURE, SOLID 2X'S OR PLYWOOD BUTYL SEALANT TOP & BOTTOM OF SEALER STRIP NOTE: VALLEY FLASH MUST HAVE SOLID SUPPORT View installation videos at Fabral.com/videos 29 POST FRAME TRIM DETAILS FASTENER PER STANDARD EAVE PATTERN ROOF PANEL 2" FASTENER @ EVERY MAIN RIB BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE FLASH AT-2 OR AGR-N4 (GRANDRIB 3) INSIDE CLOSURE OUSIDE CLOSURE ROOF PANEL PURLIN GAMBREL BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE NOTE: SPECIFY BOTH ROOF PITCHES WHEN ORDERING AT-2 FLASH. AGRN-4 FOR GRANDRIB 3 AND AGRN-5 FOR STRONGRIB ARE FOR 3/12 TO 15/12 GAMBRELS. 16. GAMBREL (PAGE 23) BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE FASTENERS PER STANDARD EAVE PATTERN BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE INSIDE CLOSURE 2" FASTENER @ EVERY MAIN RIB PURLIN FLASH AT-1 ROOF PANEL OUSIDE CLOSURE NOTE: SPECIFY BOTH ROOF PITCHES WHEN ORDERING AT-1. STANDARD IS 9/12 TO 3/12. TRANSITION 30 17. TRANSITION (PAGE 23) Fabral.com / 800.477.2741 POST FRAME TRIM DETAILS BOX GABLE ROOF PANEL VERSION 1 FLASH AC-1 OR AC-4 ROOF PURLIN FASTENER @ 24" O.C. MAX. FLASH AB-1, AB-2, AB-3, OR AB-4 BUTYL SEALANT TAPE FASTENER @ EVERY MAJOR RIB OUTSIDE CLOSURE (OPTIONAL) BUTYL SEALANT TAPE TOP & BOTTOM OF SEALER STRIP END RAFTER FASTENER 24" O.C. MAX. SIDING PANEL BUTYL SEALANT TAPE BOX GABLE VERSION 2 1. BOX GABLE (PAGE X) ROOF PANEL FLASH AG-1 ROOF PURLIN FLASH AB-1, AB-2, AB-3, OR AB-4 FASTENER @ EVERY MAJOR RIB FASTENER @ 24" O.C. MAX. BUTYL SEALANT TAPE OUTSIDE CLOSURE (OPTIONAL) BUTYL SEALANT TAPE TOP & BOTTOM OF SEALER STRIP FASTENER @ 24" O.C. MAX. END RAFTER BUTYL SEALANT TAPE SIDING PANEL View installation videos at Fabral.com/videos 31 POST FRAME TRIM DETAILS GABLE ROOF PANEL VERSION 1 FLASH AG-4 FASTENER @ 24" O.C. MAX. BUTYL SEALANT TAPE PURLIN FASTENER @ EVERY MAJOR RIB SIDING PANEL END RAFTER OPTIONAL BUTYL SEALANT TAPE TOP AND BOTTOM OF SEALER STRIP OUTSIDE CLOSURE (OPTIONAL) GABLE VERSION 2 10. GABLE (PAGE 19) ROOF PANEL FLASH AC-1 OR AC-4 FASTENER @ 24" O.C. MAX. BUTYL SEALANT TAPE PURLIN FASTENER @ EVERY MAJOR RIB SIDING PANEL END RAFTER OPTIONAL BUTYL SEALANT TAPE TOP AND BOTTOM OF CLOSURE OUTSIDE CLOSURE (OPTIONAL) 32 GABLE (PAGE 19) Fabral.com / 9. 800.477.2741 POST FRAME TRIM DETAILS FLYING GABLE DETAIL OVERHANG ROOF PANELS TO CREATE APPROX. 1" OVERHANG CE-1 UNDERLAYMENT BUTYL SEALANT TOP & BOTTOM OF SEALER STRIP SEALER STRIP (ASPHALT IMPREGNATED) FASTENER FASCIA BOARD 2" FASTENER @ GABLE (PAGE 20) 11. FLYING EVERY MAIN RIB MONOSLOPE RIDGE CAP OUSIDE CLOSURE BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE SIDING UNDERLAYMENT ROOF STRUCTURE MONOSLOPE RIDGE SLOPING RAFTER View installation videos at Fabral.com/videos 33 POST FRAME TRIM DETAILS RIDGE/PEAK- NON VENTED AR-3, RIDGE FLASHING 2" LONG FASTENER @ EVERY MAIN RIB ROOF PANEL OUTSIDE CLOSURE (ON HIP ROOFS, USE 1" X 1" X19'-8" SEALER STRIP & RR-1 FLASHING) BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE ROOF PURLIN 6. RIDGE/PEAK - NON VENTED (PAGE 16) CUT 4-BEND RIDGE CAP FOR FINISHED END AR-3, RR-1 RIDGE FLASH VENTED RIDGE 2" LONG FASTENER @ EVERY MAIN RIB ROOF PANEL VERSAVENT RX-10 BUTYL SEALANT TAPE ROOF PURLIN 34 Fabral.com / 800.477.2741 POST FRAME TRIM DETAILS ALTERNATE VENTED RIDGE RR-1 RIDGE FLASH 2-1/2" FASTENER @ EVERY MAIN RIB ROOF PANEL FASTENER PER STANDARD PATTERN CORRUGATED VENT OPTIONAL J-CHANNEL FOR SUPPORT UNDERLAYMENT ROOF PANEL ROOF STRUCTURE OUTSIDE CLOSURE WITH BUTYL SEALANT TOP AND BOTTOM BASE GUARD 8. ALT. VENTED RIDGE (PAGE 17) SIDING PANEL STAINLESS STEEL FASTENER PER STANDARD SIDING PATTERN INSIDE CLOSURE (OPTIONAL) FLASH ABG-1 BARRIER BETWEEN METAL AND ACQ TREATED LUMBER TREATED BASE PLANK FLOOR GRADE View installation videos at Fabral.com/videos 35 POST FRAME TRIM DETAILS DOOR HEADER DOOR HEADER SIDING PANEL FASTENERS PER FASTENER PATTERN FLASH AD-1 FLASH AL-2, AL-3, AL-4, AL-5, OR AL-7 DOOR STOP DOOR GIRT DOOR JAMB 31. DOOR HEADER (PAGE 28) SIDING PANEL VERSION 1 DOOR JAMB FASTENERS PER FASTENER PATTERN DOOR STOP DOOR FLASH PJFB FASTENER 36 Fabral.com / 800.477.2741 POST FRAME TRIM DETAILS DOOR JAMB VERSION 2 GIRT SIDING PANEL FASTENERS PER FASTENER PATTERN DOOR JAMB BUTYL SEALANT TAPE FLASH AL-2, AL-3, AL-4, AL-5, OR AL-7 DEPENDING ON WIDTH OF JAMB DOOR STOP DOOR FLASH AJ-3 FASTENER DOOR JAMB VERSION 3 GIRT FASTENERS PER FASTENER PATTERN SIDING PANEL BUTYL SEALANT TAPE 24. DOOR JAMBSFASTENER (PAGE 26) DOOR JAMB FLASH AJ-2 1 X 3 DOOR STOP DOOR View installation videos at Fabral.com/videos 37 POST FRAME TRIM DETAILS OVERHEAD DOOR JAMBS VERSION 1 VERSION 3 GIRT DOOR JAMB GIRT FASTENERS PER FASTENER PATTERN FASTENERS PER FASTENER PATTERN POST POST OVERHEAD DOOR SIDING PANEL OVERHEAD DOOR SIDING PANEL DOOR JAMB DOOR JAMB DOOR JAMB FLASH AL-3, AL-4, AL-5, OR AL-7 BUTYL SEALANT TAPE FASTENER BUTYL SEALANT TAPE FASTENER FLASH AL-5 OR AL-7 1 X 3 GUIDE BUTYL SEALANT TAPE FLASH AJ-4 FASTENER 1 X 3 GUIDE FLASH AJ-3 26. OVERHEAD DOOR JAMBS (PAGE 27) VERSION 2 GIRT FASTENERS PER FASTENER PATTERN SIDING PANEL 29. OVERHEAD DOOR JAMBS (PAGE 27) VERSION 4 DOOR JAMB GIRT DOOR JAMB FASTENERS PER FASTENER PATTERN POST OVERHEAD DOOR POST OVERHEAD DOOR SIDING PANEL DOOR JAMB DOOR JAMB FASTENER 1 X 3 GUIDE FLASH PJFB BUTYL SEALANT TAPE FASTENER 1 X 3 GUIDE FLASH AJ-2 27. OVERHEAD DOOR JAMBS (PAGE 27) 38 Fabral.com / 800.477.2741 30. OVERHEAD DOOR JAMBS (PAGE 27) POST FRAME TRIM DETAILS WALL GIRT SIDING PANEL POST BUTYL SEALANT TAPE FASTENER 2 X 2 FILLER BLOCK BUTYL SEALANT TAPE FASTENER OPTIONAL AL-3 TRIM AJ-4 JAMB TRIM BUTYL SEALANT TAPE FLASH AL-6 FLASH AJ-3 FASTENER SIDING PANEL SLIDING DOOR SLIDING DOOR JAMB 32. SLIDING DOOR JAMB DETAIL (PAGE 28) SLIDING DOOR HEADER SLIDING DOOR BASE SIDING PANEL SIDING PANEL ON SLIDING DOOR FASTENERS PER FASTENER PATTERN FASTENERS PER FASTENER PATTERN FLASH AH-2, AH-3, AH-4, OR AH-5 DEPENDING ON PARTICULAR MANUFACTURER'S DOOR TRACK BEING USED SLIDING DOOR GIRT OVERHEAD DOOR TRACK FLASH AD-1 FASTENERS PER FASTENER PATTERN TREATED BASE PLANK TRACK SUPPORT FLOOR 2 X 6 TRACK BOARD GRADE SLIDING DOOR GIRT SIDING PANEL ON SLIDING DOOR 33. SLIDING DOOR HEADER (PAGE 29) View installation videos34. at SLIDING Fabral.com/videos 39(P DOOR BASE POST FRAME TRIM DETAILS WINDOW SILL WINDOW HEADER WINDOW UNIT SIDING PANEL 1 X 6, BEVELED FASTENERS PER FASTENER PATTERN BUTYL SEALANT TAPE FLASH AJ-3 2X4 2X4 INSIDE CLOSURE (OPTIONAL) AD1 DRIP CAP FASTENERS PER FASTENER PATTERN WINDOW UNIT SIDING PANEL 37. WINDOW HEADER (PAGE 36. WINDOW SILL (PAGE 30) WINDOW JAMB METAL SIDING OR TRANSLUCENT ROOF PANEL GIRT SIDING PANEL TRANSLUCENT PANEL 2" FASTENER @ EVERY MAIN RIB OR 12" O.C. MAX. 2X4 FLASH AZ-2 FASTENER OPTIONAL BUTYL SEALANT TAPE FLASH AJ-3 WINDOW UNIT FASTENERS PER FASTENER PATTERN BUTYL SEALANT TAPE INSIDE CLOSURE (OPTIONAL) OUTSIDE CLOSURE (OPTIONAL) GIRT BUTYL SEALANT TAPE METAL SIDING OR TRANSLUCENT ROOF PANEL 8. WINDOW JAMB (PAGE 30) 35. 40 TRANSLUCENT ROOF PANEL (PAGE Fabral.com / 800.477.2741 POST FRAME TRIM DETAILS POST BUTYL SEALANT TAPE FASTENER @ 24" O.C. MAX. GIRT FLASH AC-2 SIDING PANEL FASTENERS PER FASTENER PATTERN INSIDE CORNER VERSION 1 GIRT SIDING PANEL 21. INSIDE CORNER (PAGE 25) FASTENERS PER FASTENER PATTERN BUTYL SEALANT TAPE POST VERSION 2 GIRT SIDING PANEL FASTENERS PER FASTENER PATTERN BUTYL SEALANT TAPE POST FASTENER @ 24" O.C. MAX. FLASH AC-1 OR AC-4 19. OUTSIDE CORNER (PAGE 24) OUTSIDE CORNERS FASTENER @ 24" O.C. MAX. FLASH AC-1 OR AC-4 View installation videos at Fabral.com/videos 41 RESIDENTIAL exposed-fastener panel TRIM DETAILS All residential flashings are formed for a 4/12 pitch unless otherwise requested by the customer. RESIDENTIAL VENTED EAVE UNDERLAYMENT INSIDE CLOSURE BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE FASTENER PER STANDARD EAVE PATTERN FABRAL ALUMINUM SOFIT ROOF PANEL TOP PLATE FLASH CE-1 FASTENER @ 24" O.C. MAX. F/J TRIM SIDING PANEL FASTENER RESIDENTIAL EAVE 44. RES. VENTED EAVE (PAGE 35) ROOF STRUCTURE UNDERLAYMENT FLASH CE-1 FASTENER PER STANDARD EAVE PATTERN FASTENER @ 24" O.C. MAX. 42 Fabral.com / 800.477.2741 BUTYL TAPE SEALANT ON TOP & BOTTOM OF CLOSURE INSIDE CLOSURE RESIDENTIAL TRIM DETAILS RESIDENTIAL ENDWALL SIDING 2" FASTENER @ EVERY MAIN RIB FLASH ASW-1 BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE UNDERLAYMENT ROOF STRUCTURE ROOF PANEL OUTSIDE CLOSURE RESIDENTIAL SIDEWALL 47. RES. ENDWALL (PAGE 36) SIDING FLASH ASW-1 FIELD BEND AS REQUIRED 2" FASTENER @ 24" O.C. MAX. BUTYL SEALANT TAPE ROOF PANEL ROOFING FELT AND ICE AND WATERSHIELD FOR ADDED WEATHER TIGHTNESS ROOFING STRUCTURE View installation videos at Fabral.com/videos 43 RESIDENTIAL TRIM DETAILS RESIDENTIAL VALLEY SCREWS EACH SIDE OF MAIN RIB (EAVE / ENDLAP PATTERN) CUT ROOF PANEL AS NECESSARY RV-2 SHOWN PEEL & STICK SEALER STRIP, 1" X 1" X 19'-8" BLOCK CLOSURE, FILL RIB VOIDS ROOF STRUCTURE, SOLID 2X'S OR PLYWOOD SOLID SUPPORT IS REQUIRED UNDER THE VALLEY. PEEL & STICK IS RECOMMENDED UNDER LAPPED ROOF PANELS AND VALLEY FLASHING. LINING MUST CONTINUE DOWN TO EAVE LINE. BUTYL SEALANT TOP & BOTTOM OF SEALER STRIP 52. RES. VALLEY (PAGE 42) DORMER VALLEY RIDGE TRIM OUTSIDE CLOSURE, TAPE SEALANT TOP & BOTTOM ROOF PANEL LOWER VALLEY TRIM UNIVERSAL CLOSURE, TAPE SEALANT TOP & BOTTOM BUTYL TAPE SEALANT PEEL & STICK UNDERLAYMENT UPPER VALLEY TRIM NOTE: ROOF PANEL OMITTED ON OTHER SIDE OF RIDGE FOR CLARITY. 44 39. DORMER VALLEYS (PAGE 43) Fabral.com / 800.477.2741 RESIDENTIAL TRIM DETAILS RESIDENTIAL GAMBREL ROOF PANEL FASTENER PER STANDARD EAVE PATTERN BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE 2" FASTENER @ EVERY MAIN RIB UNDERLAYMENT INSIDE CLOSURE FLASH AT-2 OR AGR-N4 (GRANDRIB 3) OUTSIDE CLOSURE ROOF PANEL ROOF STRUCTURE BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE NOTE: SPECIFY BOTH ROOF PITCHES WHEN ORDERING AT-2 FLASH. AGRN-4 FOR GRANDRIB 3 AND AGRN-5 FOR STRONGRIB ARE FOR 3/12 TO 15/12 GAMBRELS. 48. RES. GAMBREL (PAGE 37) RESIDENTIAL TRANSITION BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE FASTENER PER STANDARD EAVE PATTERN 2" FASTENER @ EVERY MAIN RIB INSIDE CLOSURE ROOF PANEL FLASH AT-1 ROOF STRUCTURE OUTSIDE CLOSURE BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE 50. RES. TRANSITION (PAGE 38) View installation videos at Fabral.com/videos 45 RESIDENTIAL TRIM DETAILS RESIDENTIAL PIPE BOOTS VENTILATION PIPE (OPTIONAL) SILICONE SEALANT AROUND CUT OF BOOT PIPE BOOT BUTYL SEALANT TAPE UNDER BSE OF PIPE BOOT ROOF PANEL SCREWS SPACED 2" TO 3" MAX AROUND BASE TO SECURE ROOF STRUCTURE UNDERLAYMENT SKYLIGHT 51. RES. PIPE BOOTS (PAGE 38) SKYLIGHT SECTION A-A and B-B on following page 46 Fabral.com / 800.477.2741 59. SKYLIGHT RESIDENTIAL TRIM DETAILS SKYLIGHT FLASH ASW-1 FIELD BEND AS REQUIRED FRAMING 2" FASTENER @ 6" O.C. MAX. BUTYL SEALANT TAPE ROOF PANEL SKYLIGHT SECTION A-A UNDERLAYMENT SECTION A-A ROOF STRUCTURE SKYLIGHT 53. SKYLIGHT (PAGE 40) SEALANT FLASHING - REVERSE AL FLASHING CONTINUOUS SIKAFLEX CAULK @ PERIMETER 2" FASTENER @ 6" O.C. MAX. BUTYL SEALANT TAPE UNDERLAYMENT SECTION A-A ROOF STRUCTURE ROOF PANEL SKYLIGHT SECTION B-B SECTION B-B 54. SKYLIGHT (PAGE 40) SKYLIGHT SEALANT 2" FASTENER @ EVERY MAIN RIB ASW-1 FLASHING FIELD MODIFIED TO FIT BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE FRAME ROOF PANEL OUTSIDE CLOSURE UNDERLAYMENT ROOF STRUCTURE 55. SKYLIGHT (PAGE 40) View installation videos at Fabral.com/videos 47 RESIDENTIAL TRIM DETAILS CHIMNEY DETAILS VERSION 1 BRICK 1 2" SAW CUT REGLET - 1" DEEP, BLOW OUT DUST & FILL WITH SIKAFLEX SEALANT. SET FLASH & FASTEN WITH COMPATIBLE MASONRY ANCHOR. FLASH ASW-1 FIELD MODIFY AS REQUIRED 2" FASTENER @ 24" O.C. MAX. BUTYL SEALANT TAPE ROOF PANEL UNDERLAYMENT ROOF STRUCTURE BRICK 56. CHIMNEY (PAGE VERSION 41) 2 CONTINUOUS SIKAFLEX CAULK @ PERIMETER SAW CUT REGLET 21" - 1" DEEP, BLOW OUT DUST & FILL WITH SIKAFLEX SEALANT. SET FLASH & FASTEN WITH COMPATIBLE MASONRY ANCHOR. FLASHING - REVERSE AL FLASHING 2" FASTENER @ 24" O.C. MAX. BUTYL SEALANT TAPE ROOF PANEL UNDERLAYMENT ROOF STRUCTURE 48 Fabral.com / 800.477.2741 RESIDENTIAL TRIM DETAILS CHIMNEY ENDWALL BRICK SAW CUT REGLET 21" - 1" DEEP, BLOW OUT DUST & FILL WITH SIKAFLEX SEALANT. SET FLASH & FASTEN WITH COMPATIBLE MASONRY ANCHOR. 2" FASTENER @ EVERY MAIN RIB FLASH ASW-1 FIELD MODIFIED TO FIT BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE OUTSIDE CLOSURE ROOF PANEL UNDERLAYMENT ROOF STRUCTURE 58. CHIMNEY (PAGE 41) RESIDENTIAL RIDGE/HIP 2" FASTENER @ EVERY MAIN RIB RIDGE CAP RR-1 OR AR-3 ROOF PANEL BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE OUTSIDE CLOSURE (ON HIP ROOFS USE 1" X 1" X 19'-8" SEALER STRIP AND RR-1 FLASHING) UNDERLAYMENT ROOF STRUCTURE 41. RES. RIDGE/HIP (PAGE 34) View installation videos at Fabral.com/videos 49 RESIDENTIAL TRIM DETAILS RESIDENTIAL VENTED RIDGE 2" FASTENER @ EVERY MAIN RIB RIDGE CAP RR-1 OR AR-3 ROOF PANEL CORRUGATED VENT BUTYL SEALANT TAPE TOP & BOTTOM OF CLOSURE OUTSIDE CLOSURE (ON HIP ROOFS USE 1" X 1" X 19'-8" SEALER STRIP AND RR-1 FLASHING) UNDERLAYMENT ROOF STRUCTURE 42. RES. VENTED RIDGE (PAGE 34) RESIDENTIAL GABLE ROOF PANEL FASTENER BUTYL TAPE RG-1, WG-1, OR AG-4 SCREW FASTENER @ 24" O.C. MAX. ROOF STRUCTURE UNDERLAYMENT 50 Fabral.com / 800.477.2741 PAINT SYSTEMS & WARRANTIES EnduracoteВ® is a paint system that takes performance to the next level. Based on cutting edge resin technology, this system offers unbeatable durability and superior long-term performance against the elements. The EnduracoteВ® Warranty for Galvanized Panels вЂў Lifetime film integrity for walls & roofs вЂў 30-year against fade & chalk for walls and roofs вЂў 10-year edge rust against acid rain OTHER WARRANTIES Polyester Paint Warranty вЂў вЂў 25-year limited film integrity 10-year against fade & chalk For profiles: MP Panel, ShelterguardВ®, 5-Rib For profiles: Grand Rib 3, 5V Crimp, ProClad, StrongClad, Prime Rib, Grandbeam The EnduracoteВ® Warranty for GalvalumeВ® Panels вЂў Lifetime film integrity for walls & roofs вЂў 30-year against fade & chalk for walls and roofs вЂў 20 year non-perforation warranty GalvalumeВ® Perforation Warranty вЂў 20-year non-perforation warranty for Grandrib 3, Mighti-Rib, Climaguard, Horizon S and 1 1/2вЂќ SSR Galvalume is a registered trademark of BIEC International. For profiles: Grandrib 3, 1 1/2вЂќ SSR, Climaguard, Mighti-Rib, Horizon S, Horizon 16, Ultra-Loc, Ultra-Rib The EnduracoteВ® PLUS Warranty вЂў вЂў вЂў вЂў Lifetime film integrity for walls & roofs 30-year against fade & chalk for walls and roofs 15-year edge rust against acid rain 25-year non-perforation against acid rain for walls; 20-years for roof Aluminum Product Guarantee вЂў 30-year corrosion guarantee For profiles: Grandrib 3 PLUS Product Warranties are available upon request The ENERGY STARВ® Program The ENERGY STAR Program promotes highly reflective roof systems that reflect solar energy. These roof systems allow buildings to stay cooler and, in turn, use less electricity for air conditioning; less electricity means a reduction in power generation and a reduction of pollutants discharged at power plants. Fabral has attained ENERGY STAR approval for many of its EnduracoteВ® system colors. Ask for Technical Bulletin #724 titled вЂњENERGY STAR ApprovalвЂќ, for program details and a list of approved EnduracoteВ® colors. All Fabral Enduracote Colors are ENERGY STAR Approved Please contact your Fabral representative for more information about Fabral warranties and paint systems. 51 GRANDRIB 3 PLUS, GRANDRIB, MIGHTI-RIB, MP-PANEL, PROCLAD, HORIZON CLIMAGUARD, FABRIB, ENDURACOTE, FABRAL, FABRAL CORE are registered trademarks of Euramax International, Inc. UL is the trademark of UL LLC Galvalume is the trademark of BIEC International Inc. В© Fabral 2013. All rights reserved. Fabral.com 800.477.2741 98-32-007 - 1/13