How to add cameras according to each CMS via ONVIF, RTSP ONVIF_ver0.00.09 CMS company Product Version Protocol If you can't access stream of camera using Onvif, Please check the following two conditions. 1 Milestone (Server /Client) XProtect Go ver2.0a GeoVision GV-NVR ver8.5 page 1 ONVIF 2 ONVIF 8 RTP/RTSP 11 ver3.5.20 ONVIF 15 ONVIF 20 RTP/RTSP 24 2 3 4 NUUO 5 Digifort Enterprise ver6.5 6 ExacqVision ExacqVision Client ver4.8.11 7 Luxriot Luxriot ver2.0.2.1530 ONVIF 26 8 Axxon AxxonSmart CMS ver2.1.1 ONVIF 35 9 Qnap ONVIF 39 10 Mirasys DVMS ver5.12.4 ONVIF 43 11 EverMedia NV5000 Series ver7.7.0.0.127SP4 RTP/RTSP 47 0 ` If you can't access stream of camera using Onvif, Please check the following two conditions. - First, Unckeck - Second, "Use Security on Onvif" and Save Unckeck "Use Authentication" and Save 1 ` 1. How to add camera on Milestone XProtect Go via Onvif 1. Run XProtect Go Click mouse 2. "XProtect Go Management Application" Add Device Step 1 Click mouse "1.Add Hardware Devices..." 2 ` 3. Add Device Step 2 Check "Manual", and Click mouse "Next" 4. Add Device Step 3 Check "Use", Fill "Address , Port, User Name, Password", Select Hardware Driver "ONVIF Conformant Device(2-16 channel)", Click mouse "Next" 3 ` 5. Add Device Last Check "Finish" 6. Add Device with RTP/RTSP/TCP -- Step 1 Double Check "Camera 1" 4 ` 7. Add Device with RTP/RTSP/TCP -- Step 2 Check "Video", and Check "Configure Video properties" 8. Add Device with RTP/RTSP/TCP -- Step 3 Select "Protocol - RTP/RTSP/TCP", and Click "OK" 5 ` 9. Finish Job 6 ` Milestone Client Issue if you see like this message "The server has lost connection to the camera" on the Milestone Client. Uncheck "Microphone" Restart Application. 7 ` 2. How to add camera on GeoVision GV-NVR via Onvif 1. Run GV-NVR 2. Configure пѓ System Configure пѓ IP Camera Install 4. Click “Add Camera” on IP Device Setup page 8 ` On Select Brand window Enter Server IP, HTTP Port, User name, Password On Brand, choose Protocol On Device, choose ONVIF 5. Choose Codec and Click “Apply” 9 ` 6. After finding the camera, click the right button of mouse Change position -> choose the camera position 7. After confirming the camera, Click “OK” 8. Checking the picture 10 ` 3. How to add camera on GeoVision GV-NVR via RTP/RTSP (RTP/TCP) 1. Run GV-NVR 2. Configure пѓ System Configure пѓ IP Camera Install 3. Choose “Add Camera” on IP Device Setup window 11 ` 4. On Select Brand window Enter Server IP, HTTP Port, User name, Password On Brand, choose “Protocol” On Device, choose “RTSP over TCP” 5. After entering RTSP command, Click OK 12 ` 6. After entering RTSP Port, Click “Apply” 7. After finding the camera, click the right button of mouse Change position пѓ Choose the camera position 8. After confirming the camera and click “OK” 13 ` 9. Checking the picture 14 ` 4. How to add camera on NUUO NVR via Onvif 1. Run NVR Click mouse "NUUO Main Console" Click mouse "Input ID/Password" 15 ` 2. Add Device Step 1 Check "General Setting" 3. Add Device Step 2 Click "Setting" пѓ Click "System Setting" 16 ` 4. Add Device Step 3 Fill in the blank item, "Name, IP Address, Http Port, User Name, Password ", and Check Protocol "TCP or UDP", We are not support HTTP now. Select Vendor "ONVIF". Press alphabet 'o' or 'O', you can select more easily. 17 ` 5. Add Device Last Click "Yes or OK " button 18 ` 6. Finish Job 19 ` 5. How to add camera on Digifort CMS via Onvif 1. Run Enterprise Administration Client 2. Choose Digifort Servers пѓ Click Add Server пѓ Register the server 3. Double click the server пѓ Enter ID/ Password 20 ` 4. Choose Recording Server пѓ Cameras, Click Add 5. Fill in Camera Name, Camera Description Choose Manufacturer ONVIF Fill in Recording Directory 21 ` 6. Fill in Camera Address, Port, User, Password Click OK 7. Check if it is working well at Recording Server пѓ Status 22 ` 8. Run Digifort Enterprise Surveillance Client 23 ` 6. How to add camera on ExacqVision CMS via RTP/RTSP 1. Start ExacqVision Client 2. Make sure that server is connected (Add Server) 3. IP camera -> fill in username / password 4. Hostname/IP Address -> rtsp://<IP address>/stream1 (i.e rtsp://10.1.10.10/stream1) 5. Click “Apply” 6. Make sure that camera is connected 24 ` 7. Camera Recording Setup -> Make sure that “video detected” appeared as “Yes” 8. Select the camera that you registered. You will see live picture like below. 25 ` 7. How to add camera on Luxriot CMS via Onvif 1. Run Luxriot CMS Click mouse 2. "DVR Client" Add Device Step 1 Mouse Right-button Click "Video" and Click "Camera Setup Wizard" 26 ` 3. Add Device Step 2 Click "Next" 4. Add Device Step 3 Click "Network Devices(IP Camera, Video Server)" and Click "Next" 27 ` 5. Add Device Step 4 Fill in the "Device title" , Click "Properties" 28 ` 6. Add Device Step 5 Click "Generic" пѓ Click "ONVIF Compatible" пѓ Click "Apply " 29 ` 7. Add Device Step 6 Fill in the blank item, "IP Address, Http Port, User Name, Password ", then, Click "Apply " 30 ` 8. Add Device Step 7 Click "Next" 31 ` 9. Add Device Step 8 Click "Next" 10. Add Device Step 9 Click "Next" 32 ` 11. Add Device Step 10 Click "Next" 12. Add Device Step 11 Click "Finish" 33 ` 13. Finish Job 34 ` 8. How to add camera on Axxon Smart CMS via Onvif 1. Run AxxonSmart CMS Click mouse "Axxon Smart " Check Server Name and Fill in the "Input ID/Password". default value is root/root 35 ` 2. Add Device Step 1 Click " 3. ". Add Device Step 2 Click "Devices" пѓ Click " " 36 ` 4. Add Device Step 3 Fill in the item, "IP Address, Http Port,ID, Name", and Check Produced by "ONVIF". ". Press alphabet 'o' or 'O', you can select more easily. Click "Apply". 37 ` 5. Add Device Last ( Apply ID/PW for RTSP) Fill in the "Login ID and Password". and Click "Apply". 6. Finish Job 38 ` 9. How to add camera on Qnap NVR via Onvif 1. Run Qnap NVR Type address of NVR on web-browser. and Input ID/Password. 39 ` 2. Add Device Step 1 Click "System configuration". and Input ID/Password. 3. Add Device Step 2 Click "Camera Settings" 40 ` 4. Add Device Step 3 Select Camera Number for addition. Fill in the blank item, "Camera Name, IP Address, Port (Web), User Name, Password ". Select Brand "ONVIF". Click "Test" button, if you set all information. If test is ok, click "Apply" for saving information. 41 ` 5. Finish Job 42 ` 10. How to add camera on Mirasys DVMS via Onvif 1. Run DVMS Click mouse "DVMS System Manager" Fill in the blank item "User name, Password". Default is "Admin/0308" Click " " 43 ` 2. Add Device Step 1 ", Recorders Check " Click " Click " 3. Hardware " and " Add Device Step 2 Select Model "Automatic Camera search", and Fill in the item, " IP Address, Http Port, User Name, Password ", and Click " " 44 ` Wait until finish job. if cms find any camera, then display like below picture. Click " " 45 ` 4. Finish Job 46 ` 11. How to add camera on EverMedia HybridDVR via Onvif 1. Run NV5000 2. Once software and driver are installed, go to “Setup” Select “IP camera” and click “ADD IPCam” button. Note : Since RTSP/RTP doesn’t support motion detection from camera, you have to use motion detection feature from software. Please, go to “motion recording” section for reference. “Detail” feature doesn’t work when camera is connected through RTSP. 47 ` 3. Select protocol “RTSP_RTP” and Model “TCP” IP Camera Site: rtsp://192.168.1.30/stream1 : 554 (RTSP Port Number) Click “Authentication” and Input ID and Password ( default : admin / admin) Click “Connect”. If you see live picture, click “Save & Exit” 48 ` Motion Recording 1. Go to “Setup” and “Recording” 2. Click “Advanced” 49 ` 3. Select “Region” 50 `
© Copyright 2024 Paperzz
