MobilePower HYDRAULIC COMPONENTS www.fleetpride.com V3-1.2014 MobilePower FleetPride is proud to distribute these and many other national brands We are committed to reducing your downtime by getting you the parts you need, when you need them. That’s why we offer the most recognized brands from the top manufacturers in the industry, and exclusive brand products that deliver both quality and value. ® 2 MOBILE POWER 3 TABLE OF CONTENTS PRODUCTS PAGE(S) Cylinders 4 Parker - Mobile Cylinders - Double & Single Action - Hoist - Telescopic - Tie Rod PTO’s Chelsea - Bezares USA - Muncie - Mechanical, Clutch & Powershift Units - PTO Flanges - Valves & Pumps Directional & Control Valves Parker/Gresen - Monoblock - Relief - Accessory - Directional Control - Sectional Control Valves Gear Pumps / Motors Parker - Vantage Power - Single & Multiple Pumps / Motors - Cast Iron - Dump Pumps Vane Pumps / Refuse Permco - Denison - Vickers - Live/Moving Floor/Dump Trailers - Clutch Pumps - Single/Dual Vane - Refuse Industrial Pumps / Motors Permco - Roller Bearing Pumps/Motors - Sleeve Bushing Pumps/Motors Piston Pumps / Motors Bezares USA - Parker - Hydro Leduc - Bent Axis - Variable & Displacement - XA & MA Series Motors Eaton-Char-Lynn - Parker - H & S Series - 2000 Series - Small & Large Frame 5-8 9 - 10 11 - 13 14 - 15 16 17 18 Blowers / Pumps / Compressors 19 Vacuum Pumps / Coolers 20 Miscellaneous 21 Paragon - Blackmer - Ingersoll-Rand - Ranger - Roper - P857 Blower - Product Pumps - Oil/Oil Free Compressors Fruitland - Challenger - Masport - Paragon - SS Thermaflow - Vacuum/Pressure Pumps - Hydraulic Oil Coolers Road Watch Temperature Controls - Line Filters - Clutch Pump Parts - Valves/Fittings - Test Equipment - Cylinders Consoles / Controls Apsco - Vantage Power - Cross - Air Actuators - Consoles/Hoist & PTO Controls - Lift Axle Accessories - Stackable Swivel Pedestals - Directional Control Cable Controls Cablecraft - Wescon - Button/Push-Pull Standard - Micro Adjust - Custom - Remote Control System Assemblies 22 - 23 24 Controllers 25 Wet Line System Products 26 Vantage Power 27 Parker - Dickey-John - Single - Dual Spreader Control - QDB Series - Control Point - LT Control Vantage Power - Complete Systems - Combo Kits - Hydraulic Reservoirs Aluminum/Polyethylene & Steel Pneumatic Air Controls - Hydraulic Gear Pumps - Dump Pumps - Reservoirs Not all parts and/or components are in stock at every location. The parts in this catalog are manufactured by either the original equipment manufacturer or aftermarket parts manufacturers. The original equipment manufacturers’ names, drawings, colors and part numbers, are used for identification purposes only and we are in no way implying that all of our products are original equipment parts. FleetPride or the FleetPride Mobile Power Division is not liable for damages due to omissions or typographical errors. 4 MOBILE POWER MOBILE CYLINDERS Your Leading Source For Hydraulic Cylinders FleetPride carries the industry leading brand name cylinders from Parker Commercial Intertech. We can supply your needs for welded type single & double acting, telescopic, hoist, and tie rod cylinders! Cylinder Applications l Dump Trucks l Dump Trailers l Roll Off Hoist l Refuse Packers & Many More! Contact your local FleetPride location or FleetPride Mobile Power toll free at 888-338-5352 or fax 203-287-3720 for availability and technical support. Download our FREE Mobile App today! MOBILE POWER POWER TAKE OFFS - PTO 5  Power Take Off - pto Proper Matching of PTO A Power Take-Off must be properly matched to the vehicle transmission and to the auxiliary equipment being powered. An improperly matched P.T.O. could cause severe damage to the vehicle transmission, the auxiliary driveshaft, and/or the auxiliary equipment being powered. Damaged components or equipment could malfunction causing serious personal injury to the vehicle operator or to others nearby. Always refer to Chelsea catalogs, literature, and owner’s manuals, and follow Chelsea recommendations when selecting, installing, repairing, or operating a PTO. Mechanical Shifted Units The mechanical shifted power take-offs such as the 442 Series family is engineered to work with virtually all existing transmission applications today. There are many advantages to these units from a removal shift cover to establish correct backlash during installation, greaseable output shafts that help solve fretting corrosion problems, and a positive shift engagement. With a wide selection of shift, speed ratios, and output options, that can be easily converted to meet your needs, these units are a true workhorse for most vehicle applications either with air brakes or without, manual or automatic transmissions. Powershift Units Chelsea Powershift PTOs deliver clash free shifts whether the vehicle is stationary or on the move. Constant mesh input gears and specially designed clutch packs make these PTOs ideal for applications that demand frequent PTO shifting, such as refuse vehicles. These units are available with over seven of today’s most popular pump mounting flanges, Electronic Overspeed Control (EOC) to protect driven equipment from over-speeding, and pressure lubrication for heavy duty applications. Fixed compression gasket eliminates setting of backlash and reduces installation time. Special low profile housing designs for vehicle interference issues are also available making the Chelsea Powershift PTOs a very wise selection for today’s demanding applications. 442 Series  Engineered to work with virtually all existing  transmission applications  Economical workhorse features a cast  iron housing  Tapered cone bearings for high torque  rating and long service life  Slip fit idler pin for easy interchange from  one transmission to another  Easy to set backlash  Wide range of shift and output options 489 Series  442 Series family, but with an 8-bolt  mounting flange  No adapter plate needed  Less installation time, less expense and  less chance of leakage  Wide range of shifter options and  pump flanges 278 Series - allison world  Enhanced housing design for  maximum transmission clearance  when direct mounting a pump  6 speed ratios and 14 output options  Internal bearing lube  SuperTorque™ gears available for  20% higher intermittent torque  ratings  Electric/hydraulic shift 560 Series  Wet spline for extended PTO and pump  shaft life  Single continuous duty torque rating  Torque rating of 335 lbs. ft. (454 N.m.)  Flow rates 3.4 to 31.7 GPM  (12.9 119.9 LPM) at 1200 RPM  Pressure ratings up to 3500 PSI (240 bars)  12 or 24 volt electric over hydraulic actuation  Pressure and sucion ports rotatable for  best clearance  Weight 71 lbs. no pump bracket required  Quiet operation 6 MOBILE POWER POWER TAKE OFFS - PTO  Power Take Offs pto 280 Series - New 230/231  Series  This new series utilizes the best of Cheslea  technology and innovations from the current  Hot Shift PTO’s.  The 280 series will combine the 277 and 278  into one model of PTO.  It will feature a single continuous duty  torque rating. No more intermittent rating.  Torque capacity ratings have been  increased.  Pump clearance issues have been  improved with rotatable cast iron flanges.  New positive stop for Driveline outputs.  Eliminates ability for shaft couplings to  damage Oil Seals.  speed ranges expanding from 5 ratios to  9 ratios.  Designed for both manual and automatic  transmissions.  231 offers low profile housing for avoiding  clearance problems.  Pressure lubrication option available for  both units.  Patent pending internal self adjusting  shaft brake option.  Air or electric air shift unit 236 Series  Patent pending internal self adjusting shaft  brake option.  Wide selection of input gears for virtually  all currently produced transmissions.  Helical gears and optional pressure  lubrication to extend PTO service life.  Inspection cove for adjusting backlash.  Air or electric air shift unit. 890 Series Mounting a flange to the rear of the transmission allows for larger pumps and in some cases it will eliminate the need for a drive shaft.  Require less space than current P.T.O.’s and  helps clear frame rails, etc.  Torque ratings up to 670 ft. lbs. and allows   the use of higher flow and pressure pumps.  The 890 Series can be installed in 2 pieces;  one lighter P.T.O.housing and then the shaft.  Wet Spline outputs – Extends shaft life.  Eliminates the need to disassemble to   frequently grease the splines. 870 Series  The 870/877 Series is a 10-bolt mounting  pattern that will fit on today’s popular  automatic transmissions.  Features six shift options four of which are  integrated into the P.T.O. housing that  require one hose for a simplified installation.  Eight internal gear ratios provide you with  a wide variety of speeds to meet your  application requirements.  The direct mount pump flange options are  available with our Wet Spline Design that  provides you with increased P.T.O. and  pump shaft life.  Versatility, power, ease of maintenance  and installation, make the 870 Series the  only choice for your vocational truck  requirements. 249 Series Quieter and more cost-effective, the Chelsea 249 Series teamed with the new Ford Transmission Noise Suppression System, provide a quiet PTO application on your Ford SuperDuty - Patent Pending.  No special installation tools to purchase  eliminating costs and saves time.  Single Hose connection and  Integrated Actuation Valve.  Single hose simplifies installation and  reduces installation time along with  eliminating leak paths.  Intermittent Torque Rating of 200 ft. lbs.  58 Horsepower @ 1200 Engine RPM  Two Year Warranty.  Pump flows up to 25.1 GPM @ 1200 Engine RPM – Standard.  Flanges  RA Flange  sae b 2 bolt 489RA Features:  Most common application is on small trucks using an Allison  World Transmission where clearance is very important when  bolting a piston or gear pump that has an SAE B 2 bolt pump. MOBILE POWER POWER TAKE OFFS - PTO 7 Bezares has been manufacturing PTO’s for the world market for over 50 years and are a leader in European and Asian PTO development, manufacturing, and distribution. Working closely with the truck and transmission manufactures from around the world, Bezares USA gives us a distinct advantage in the global PTO market. All Bezares PTO’s are built with the highest quality bearings and sealing components. 1000/2000 Series 116003 Series 3100/3150/3250 Series 6013399/602199 to 609699 Series The 1000 and 2000 series PTO’s have been engineered to work with the most common transmissions in today’s market. Offered in a wide range of input gear, ratio, output, and shifter options, these all cast iron PTO’s include large 12mm flange bolts, which make for a very sturdy and durable pump mount, supporting some of the larger pumps in the market. Both of these models are also available in a deep mount 1010 and 2010 series. 3100 and 3250 series are 10 bolt hotshift PTO’s for the Allison World Series transmissions as well as the new Caterpillar CX series. These PTO’s have seven ratio options, a wide variety of outputs, and either electric over hydraulic or air shift options. The 3250 series is a low profile version of the 3100 for tight mounting spaces on certain truck chassis. The 3150 is the constant mesh option of this series. 3200 Series This versatile 6 bolt hotshift PTO is designed for the 1000/2000 Allison transmission family, Asian automatics and a wide range of manual transmissions. The 3200 series is offered with multiple ratios and outputs, as well as electric over hydraulic and air shift options. 3900/3920 Series Our 3900 and 3920 series PTO’s have been designed for the Ford F- Series Torqueshift transmissions. Both PTO’s have both a direct as well as a remote mount output option. 4000 Series One of Bezares’ most popular products, the 4000 series PTO is a very compact, heavy duty, high torque, eight bolt PTO that was design at an economical price. It has a wide variety of ratio and output options as well as an integrated air shift cover for extra durability. 4200 Series The 4200 series PTO is a market exclusive dual output eight bolt heavy duty PTO. This unit has two independently air operated outputs, with a variety of ratio and output combinations. This PTO is very versatile for many applications where two PTO’s are needed and only one opening is availible Bezares currently manufactures and offers nine different PTO options to fit these specific transmissions around the world. Models include our standard 116003, a hot shift, a heavy duty, a single gear, and a triple output PTO amongst others. All of these PTO’s are available with any SAE or DIN output options. The Model 6013399 Split Shaft PTO is designed to provide up to two 6 bolt PTO mounting apertures for light to medium duty vehicles that may not have the PTO option or are limited to one opening. This split shaft may also offer the ability to pull more torque and horsepower than a transmission mounted PTO may be capable of providing. A wide range of Bezares PTO’s can be installed on the openings with the full range of PTO options. The PTO’s and split shaft have the options of being shifted pneumatically, mechanically or hydraulically. The 6013399 split shaft PTO mounts in the main driveline behind the transmission or behind any driveline output providing input speeds based upon the input shaft speed. 901211 Series Selector Valve Selector valve 901211 is a two position, two selector valve that offers a simple means of directing oil flow into two separate hydraulic circuits. It is air operated with an open center in neutral position. Max flow 65 gpm, maximum pressure 5000 psi. 9030890 Series Hi/Low Hydraulic Valve The 9030890 valve is an air operated dual pressure tippingvalve with two independent operating pressures. This valve is a perfect fit for a walking floor and dump combination, or even a standard dump body when ordered without the HP option. At a fraction of the cost of other options.45 gpm rated and maximum pressure 5000 psi. 8 MOBILE POWER PTO / PUMPS  PTO’s TG Series Powerflex™ PTO Our first major new product, the TG Series, has had a major impact on the PTO market in North America, with others emulating the features and benefits of the design. The TG Series is the industries’ most popular and versatile PTO design, and is still the heart of the Muncie PTO product family. The TG’s flexibility permits a wide variety of PTO/transmission applications, and wide gear design permits torque capacity for most truck equipment applications. Clutch Shift PTOs Clutch Shift PTOs provide the ability to engage and disengage the PTO without disengaging the vehicle’s clutch. They can be designed for both manual and automatic transmissions and are the preferred type of PTO for automatics. Muncie offers clutch style PTOs for SAE standard PTO openings as well as providing application specific models such as the FA and GM products. FA SERIES The FA Series PTO was designed in cooperation with Ford Motor Company for the 1999 and newer Super Duty chassis equipped with the 4R100 automatic transmission. The FA62 two wheel drive and FA64 four wheel drive mount on the driver’s side, offer a variety of direct mounted hydraulic pumps. The PTOs are shipped complete with in-dash activation controls and transmission temperature gauge as well as a complete wiring harness. Six Shifting Choices Air Shift Cable Shift Lectra Shift Lever Shift CS6 & CS8 SERIES The CS6 & CS8 Series PTOs are built for SAE standard 6 and 8 bolt opernings. A wide variety of gears allow the use of this PTO on manual transmissions as well as Allison’s family of AT & MT Series automatics.  Pumps Muncie carries a complete line of hydraulic pumps including gear, vane, and piston models. Hydraulic Pumps All pumps are pressure balanced and 100% tested before shipment. f series gear pump The F Series is the smallest of the gear pump family. It is designed with sleevetype bushings and an aluminum housing to provide high performance in a compact, lightweight package. The F Series is available in a number of configurations for special low flow applications or for general duty. k/l series gear pump Both K & L Series pumps are constructed for maximum versatility. These pumps are offered with SAE 2 & 4 bolt “B” mounting patterns and a variety of shafts as well as foot-mounted flanges. Standard pumps can be used as either a pump or hydraulic motor with side an rear ports machined into the housings. EOS-110 Overspeed Switch The EOS-110 disengages auxiliary power equipment PTOs and pumps - when an excessive operating speed is reached. It automatically re-engages equipment when engine is reduced to a safe speed. This allows full operator control within predetermined limits. Speeds can be adjusted from 300 RPM to 3000 RPMs. Easily adaptable to any gasoline or diesel engine. No mechanical connections are required. h series gear pump The H Series is most commonly used as the basis for our clutch pump product line, but is also offered in a variety of direct mount SAE “A” or remote mount configurations. The H Series is built with a cast iron housing and long life sleeve type bearings. clutch pump & mounting kit Clutch pumps are driven directly off the pulley system at the front of the engine. Kits are available for most popular engine/chassis combinations with either v-belt or poly groove compatibility. Clutch pumps are popular for applications requiring live engine power or for chassis without PTO accessibility. Refuse & Specialty Gear Pumps power pro & power miser systems These products can be driven from the engine crankshaft or by a PTO. Each provides hydraulic power at the flip of a switch. In the “off” mode, pumps receive only enough oil for lubrication purposes, saving the cost of moving fluid through the system when not in use. mlsm live pak system The MLSM Live Pak system is designed for start and stop refuse collection equipment. The system does not shut off the pump at high RPM and provides flows up to the maximum allowed for the equipment without interruption. This allows for minimum cycle times, increasing the number of collections per shift. MOBILE POWER  Two types of directional valves can be used: Open-Center valves (CFO) and Closed-Center valves (CFC). The two types of valves give completely different control characteristics. CFO valves are intended for applications in which simple, uncomplicated components are required, and where the demands for simultaneous operation characteristics are moderate. CFC valves are intended for applications in which the demands on control characteristics are great, while at the same time, a system with a fixed pump is required. Parker valves can be obtained with a large number of optional components and mountings such as:  A main pressure relief  Individually adjusted port relief and anti-cavitation valves  Separate replenishing valves with counterpressure valves  Application adapted spools and/or a large selection of spool actuators  Single or multi-pump operation by stacked valves  Subplate, stackable, or manifold styles  Load hold checks - crossover reliefs - flow controls - power beyond feature  Proportional inlets for finer metering  E-stop, pump channel blocked in emergency - valve options vary  Flows up to 197 LPM - 52 gpm  Load Sensing The directional control valve: In the load sense system, the directional control valve regulates the displacement of a variable displacement pump via a load signal line. The pump maintains a pressure difference between its outlet port and the highest load signal to supply pressure and flow to match the demand. These systems are the most advanced, offering optimum control characteristics with good efficiency/fuel economy. Parker valves can be obtained with a large number of optional components and mountings such as:  A main pressure relief  Individually adjusted port relief and anti-cavitation valves  Separate replenishing valves with counterpressure valves  Application adapted spools and/or a large selection of spool actuators  Single or multi-pump operation by stacked valves  Subplate, stackable, or manifold styles  Load hold checks - crossover reliefs - flow control  Variable or fixed pumps  Flows up to 302 LPM - 80 gpm Gresen V20 Series Directional Applications:     9 Directional Valves  Constant Flow  DIRECTIONAL VALVES Snow And Ice Control Systems Utility Equipment - Dump Bodies - Spreaders Recovery Vehicles & Refuse Equipment Lube Trucks & Cranes Features:  High tensile ductile iron for durability and shock load resistance  Compact size and lightweight to fit your installation needs  Precision machined spools with extra find metering control and low spool forces  Available in SAE or NPT porting  Stackable design to customize to your needs  Large variety of spool types and backcap options  Wide range of work port options including port reliefs, anti-cavitation valves, port restrictors,  pilot operated check valves - lock valves - and power beyond capabilities V20 TECHNICAL DATA Design Type: Sectional Circuit: Open Center Design Parallel, Tandem, Combined Parallel/Tamdem, & Series Also: Closed Center, Load Sensing, Load Sensing/Pressure Comp Available. Capacity: 30 GPM - 76 LPM Nominal - 20 GPM - 114 LPM Maximum - 30 GPM Max. System Pressure: 3500 psi Max. Tank Pressure: 200 psi Filtration: 33 Micron Spool Force: 50 lbs Maximum Temperature: 020°F - 180°F Or -29°C - 82°C Seal Type: Buna-N Standard Optional Viton Relief Valves: Shim Adjust, Optional Screw Adjust Inlet 10 MOBILE POWER CONTROL VALVES  Control Valves  Commercial DVA20/DVG20 Sectional DVA20 & DVG20 Features:  Steel castings for durability and shock load resistance for your high pressure needs  Full flow relief valves and low open center pressure drop  Parallel circuit design permits all spools to be operated independently or simultaneously with  the lightest load receiving priority  Precision machined spools are hard chrome plated for maximum life and corrosion resistance  Stackable sectional design allows for customizing the assembly to your specific needs  Modern machinery and SPC manufacturing procedures produce assemblies with minimal  internal leakage to maintain maximum load holding ability  Work sections are 100% pre-assembled and pre-tested before shipping  Large variety of spool types and backcap actions. Transition load checks are standard to prevent  load shift between spool positions  Wide range of work port options including port reliefs, anti-cavitation valves, port restrictors, and H.P.C.O.  power beyond providing flexibility for all your design needs DVA20 Inlet DVA20 & DVG20 TECHNICAL DATA Design Type: Sectional Circuit: Parallel/Open Center Capacity: 40 GPM - 152 LPM - Nominal Capacity: 60 GPM - 228 LPM - Maximum Max. System Pressure: 2500 psi - 172 Bar - SAE O.D.T. Max. System Pressure: DVA Series 2500 psi - DVG Series 3500 psi Max. Tank Pressure: 160 psi Spool Force: 50 lbs - 22.7 kg - Maximum Temperature: -20°F - 200°F Or -29°C - 93°C Seal Type: Buna-N S Relief Valves: Differential Type Adjustable From 800 To 2500 psi - 55.1 to 172 Bar - Preset At 2000 psi - 138 Bar  Commercial DVA35/DVG35 Sectional DVA35 & DVG35 Features:  Steel castings for durability and shock load resistance for your high pressure needs  Full flow relief valves and low open center pressure drop  Parallel circuit design permits all spools to be operated independently or simultaneously with  the lightest load receiving priority  Precision machined spools are hard chrome plated for maximum life and corrosion resistance  Stackable sectional design allows for customizing the assembly to your specific needs  Modern machinery and SPC manufacturing procedures produce assemblies with minimal  internal leakage to maintain maximum load holding ability  Work sections are 100% pre-assembled and pre-tested before shipping DVA35  Large variety of spool types and backcap actions. Transition load checks are standard to prevent  load shift between spool positions  Wide range of work port options including port reliefs, anti-cavitation valves, port restrictors, and H.P.C.O.  power beyond providing flexibility for all your design needs DVA35 & DVG35 TECHNICAL DATA Design Type: Sectional Circuit: Parallel/Open Center Capacity: 60 GPM - 226 LPM - Nominal Capacity: 90 GPM - 342 LPM - Maximum Max. System Pressure: DVA Series 2500 psi - DVG Series 3500 psi Spool Force: 50 lbs - 22.7 kg - Maximum Temperature: -20°F - 200°F Or -29°C - 93°C Seal Type: Buna-N Relief Valves: Differential Type Adjustable From 1500 To 3000 psi - 103.5 to 207 Bar - Preset At 2000 psi - 138 Bar Mid-Section Inlet DVG35 GEAR PUMPS / MOTORS 11 MOBILE POWER  Gear Pumps & Motors P16 Single and Multiple Pumps and Motors  P16™ Features: TP16 Series TP16  Flow range to 38 gpm - 143.8 LTR  Displacements to 3.902 CIR - 63.94 CC’s/rev.  Maximum pressure to 3000 psi - 207 bar  Maximum speed to 3600 rpm  Rotation A or C  Bearings - Journal  Cast iron gear plate w/aluminum flange & cover plate CP16 Clutch Pump General P16 Information: PVP16 Priority Valve  P20™  Available in various configurations  Cast iron pumping sections for durability  Aluminum flanges and covers for optimum  power to weight ratio  Journal bearings for long life & good over-hung  load capacity  Pressure balanced plates for greater efficiency Series Features:  Flows to 41 GPM FLOW RATE BY GEAR SET SIZE SPEED  Pressures to 3000 PSI GEAR WIDTH & GEAR OUPUT (GMP/LPM) RPM 1” 14” 12” 1w” 2” 900 6.5 8 10 12 13.5 1200 9 11.5 14 16 18.5 1500 11.5 14.5 17.5 20.5 23.5 21 25 29.5 34 2100 16.5  P30/031™  Speeds to 2400 RPM PRESSURE RATING BY GEAR SIZE Gear Set Size 0.50 IN3 1 Max RPM 2400 P20 - Max PSI 3000 0.75 1.5 2400 3000 1.00 1.97 2400 3000 1.25 2.5 2400 3000 1.50 2.96 2400 3000 1.75 3.45 2400 2500 2.00 3.94 2400 2500 Series FLOW DATA AT 2500 PSI (172 BAR) UNLESS NOTED SPEED RPM 900 1200 1500 1800 2100 2400 WIDTH & GEAR OUPUT (GMP/LPM) 1” 6.5 24.5 9 34 11.5 43.5 14 53 16.5 62.5 19 72 14” 8 30 11.5 43.5 14.5 55 18 68 21 79.5 24 91 12” 10 38 14 53 17.5 66 21.5 81.5 25 94.5 29 110 1w” 12 45.5 16 60.5 20.5 77.5 25 94.5 29.5 112 34 129 2” 13.5 51 18.5 70 23.5 89 29 110 34 129 39 148 Features:  Flows to 41 GPM - Pressures to 3000 PSI  Speeds to 2400 RPM  Priority valves - 2 speed valves & piggybacks  Winch motors Gear Set Size IN3 Max RPM P30 - Max PSI P31 - Max PSI PRESSURE RATING BY GEAR SIZE 1.00 0.50 0.75 1.50 1.25 1.97 1 1.5 2.96 2.5 2400 2400 2400 2400 2400 2500 2500 2500 2500 2500 3000 3000 3000 3000 3000 1.75 3.45 2400 2250 2500 2.00 3.94 2400 2250 2500 12 MOBILE POWER PUMPS / MOTORS  P50/P51™ Series Single and Multiple Pumps and Motors FLOW DATA AT 2500 PSI (172 BAR) UNLESS NOTED SPEED RPM 900 1200 1500 1800 2100 2400 WIDTH & GEAR OUPUT (GMP/LPM) 1” 8.5 32 12 45.5 15 57 18 68 21.5 81.5 25 14” 10.5 39.5 15 57 19 72 23 87 27 102 31 2” 17.5 66 24 91 31 117 37.5 142 44 167 51 1w” 15 57 21 79.5 27 102 32.5 123 38.5 146 44 12” 13 49 18 68 23 87 27.5 104 32.5 123 37 24” 20 75.5 27 102 35 132 42 159 49.5 187 57 22” 22 83.5 30 114 39 148 47 178 55 208 63.5 Features: PRESSURE RATING BY GEAR SIZE  Flows to 63 GPM - Pressures to 3000 PSI  Speeds to 2400 RPM  Priority valves - 2 speed valves - piggybacks  Winch motors flow Gear Set Size IN3 Max RPM P51 - Max PSI 0.50 1.29 2400 3000 0.75 1.93 2400 3000 1.00 2.57 2400 3000 1.25 3.22 2400 3000 1.50 3.86 2400 3000 1.75 4.5 2400 3000 2.00 5.15 2400 3000  P75/76™ Series Single and Multiple Pumps and Motors FLOW DATA AT 2500 PSI (172 BAR) UNLESS NOTED SPEED RPM 1” 900 11.5 32 17 1200 45.5 22 1500 57 1800 27.5 68 33 2100 81.5 38 2400 14” 15.5 39.5 22 57 29 72 33.5 87 42 102 49 WIDTH & GEAR OUPUT (GMP/LPM) 2” 22” 24” 1w” 12” 27 34.5 30.5 23 19.5 2w” 38 3” 42 27 68 35.5 32 79.5 41.5 37.5 91 48 42 102 54.5 48 114 61 52.5 114 67 58 114 74 43.5 51 59 66 74 81.5 90 51.5 60 69.5 78 87 96.5 106 59.5 70 80 90 101 111 122 Features:  Flows to 128 GPM  Pressures to 3000 PSI  Speeds to 2400 RPM PRESSURE RATING BY GEAR SIZE Gear Set Size IN3 Max RPM P76 - Max PSI P75 - Max PSI 0.50 2.02 2400 2500 3000 0.75 3.03 2400 2500 3000 1.00 4.04 2400 2500 3000 1.25 5.06 2400 2500 3000 1.50 6.07 2400 2500 3000 1.75 7.08 2400 2500 3000 2.00 8.09 2400 2500 2500 2.25 9.2 2400 2250 2500 2.50 10.25 2400 2250 2500 2.75 11.1 2400 2000 2000 3.00 12.1 2400 2000 2000 2.25 5.79 2400 2500 2.50 6.43 2400 2500 MOBILE POWER  P300/P400™ Series Single and Multiple Pumps and Motors cast iron bushing pump Features:  Three piece cast iron construction  Low friction bushing design  Heavy duty application  Single, multiple, piggy back  and thru-drive assemblies PUMPS / MOTORS 13 Model P = Pump M = Motor Options D = Stealth Gear Width .50 .75 P315 1.00 M315 1.50 1.25 1.75 2.00 .50 .75 P330 1.00 M330 1.50 1.25 1.75 2.00 .50 .75 The P300 Series pumps are available in single, multiple, piggyback, and thru-drive assemblies. Multiple pumps reduce mounting costs, allow for a small package size and common inlet capabilities. Assemblies up to six pumping sections are available. Piggyback pumps allow the combination of pump sections of different frame size to use a common inlet in tandem configuration. The thru-drive feature allows an independent piston or gear pump to be mounted to a rear SAE drive pad. Multiple section motors are also available providing enhanced torque and speed control as well as smooth torque ripple. The P400 Series of high pressure, fixed displacement gear pumps are available in single and multiple assemblies. These units are rated for service up to 4500 psi. They’re available in three models offering you a displacement range from 1.5 to 5.5 CIR. These units are cast from high-strength iron which provides the structural integrity needed at high pressures. Gear widths have been selected to keep shaft deflections and bearing loads within acceptable design limits. Body seals have been strengthened and the fastener pre-load increased to assure reliability under high pressure conditions.  C102™ Series Pump 1.00 P350 1.25 M350 1.75 1.50 2.00 2.25 2.50 .75 1.00 P365 M365 1.25 1.50 1.75 2.00 2.25 2.50 Theoretical Displacement in3/r .620 .930 1.24 1.55 1.86 2.17 2.48 .965 1.47 1.97 2.46 2.95 3.44 3.94 1.28 1.91 2.55 3.19 3.82 4.46 5.10 5.73 6.38 2.70 3.60 4.50 5.40 6.30 7.20 8.10 9.00 Mineral Oil / Maximum Pressure Continuous Intermittent cm3/r 10.2 15.2 20.3 25.9 30.5 35.6 40.6 16.1 24.2 32.3 40.4 46.4 56.5 64.6 20.9 31.3 41.8 52.2 62.7 73.1 83.6 94.0 104.5 44.3 59.0 73.8 88.5 103.3 118.0 132.8 147.5 psi 3500 3500 3500 3500 3300 2900 2500 3500 3500 3500 3500 3500 3250 3000 3500 3500 3500 3500 3500 3250 3000 2700 2500 3500 3500 3500 3500 3500 3500 3250 3000 bar psi 245 245 245 245 225 200 175 245 245 245 245 245 225 210 245 245 245 245 245 225 210 190 175 245 245 245 245 245 245 225 210 4000 4000 4000 3850 3500 3100 2750 4000 4000 4000 4000 3850 3500 3300 4000 4000 4000 4000 3850 3500 3300 3000 2750 4000 4000 4000 4000 4000 3850 3500 3300 bar 275 275 275 265 245 215 190 275 275 275 275 265 245 225 275 275 275 275 265 245 225 210 190 275 275 275 275 275 265 245 250  Dump Pumps Heavy Duty Cast Iron Features:  Patented Relief Valve Protection  Pressure To 2500 psi  Flows From 9.5 To 48 gpm  Includes G101/G102 Series  Speeds To 2400 rpm  2 & 3 Line Installation  Air Shift Kits Available C102 Dimensions VantagePower PN VPC-101-25-Z-MS-25 Parker PN C101D25 VPC-102-25-Z-L-MS-25 C102D-25-1 VPC-102-25-Z-L-AS-25 –––– VPC-102-25-Z-R-MS-25 C102D25 Description Remote mount twin shaft DIRECT MOUNT LH DIRECT MOUNT LH with air shift DIRECT MOUNT RH 14 MOBILE POWER PUMPS / REFUSE  Heavy Duty Pumps For Live And Moving Floors and Dump Trailers  Heavy Duty Clutch Pumps CP124 With Pad Mounting, Side And Rear Porting Features: Dual Use Pump Features:  Dual Pressure Relief: low for dump bodies, high for live floors  Easy to switch from low to high pressure using truck air  Large 12” NPT suction port in the gear housing  Three line system for continuous duty  Field adjustable relief settings  Doweled construction  37 GPM @ 1800 RPM - 100% factory tested  Heavy duty “controlled stress” roller bearings  Factory installed “OEM” air shift with full metering capabilities  Direct mount SAE “B” 4 bolt or twin shafted remote mount  with bracket  Relief valve protects the high pressure portion of the system  as well as the pump Gemini Dimensional Data - Inches CP124 With Bracket Mount, Side SAE O-Ring Ports  Cubic inch displacements from 0.62 through 2.48  Speeds to 3000 RPM and pressures to 3500 PSI  SAE “A” mounting with bracket or pad mounting available  Heavy duty sleeve bushing design in a small frame size  Doweled and high strength 3 piece cast iron construction  100% factory tested  NPT, o-ring, or split flange porting located on the rear and/or side  Only high torque clutches used with all the popular clutch  configurations available  Pressure balanced wear plates maintain high pump efficiency  throughout all operating ranges  Typical applications include recovery vehicles, snow plows,  spreaders, utility vehicles, winches, small hoists, aerial  devices, lift gates, cranes, and light duty equipment Gear Width (Inches) .50 .75 1.00 1.25 1.50 1.75 2.00 Displ CU IN/CC .62/10 .93/15 1.24/20 1.55/25 1.86/30 2.17/35 2.48/40 GPM/ LITERS @ 1000 RPM 2.2/8.3 3.6/13.6 4.9/18.5 6.1/23.1 7.4/28.0 8.8/33.3 10.0/37.9 Max RPM 3000 3000 3000 3000 3000 3000 3000 Min RPM 600 600 600 600 600 600 600 Max PSI/BAR 3500/241 3500/241 3500/241 3500/241 3200/220 2900/200 2500/172 CP124 Performance Chart/Specifications  Dual Pressure Controller The third sleeve is installed in the pump, therefore, the return port must be plumbed back to tank, below the oil line at all times. Gemini dual use pumps are designed to be used with dual use applications, typically a dump trailer and a live floor or goose neck. Gemini Dual-Use Pump Specifications Series IN3(CC) DG-20/RG-20 5.12 (84.3) GPM/900 RPM GPM/1200 RPM GPM/1500 RPM Max Max 2000 PSI 2000 PSI RPM PSI 2000 PSI 30.5 30.5 1800 3200 30.5 AVC-295-HP-13 This special dual pressure controller is to be used in the Gemini pump system. Features PTO On/Off / Dump raise/lower. In addition, it has an optional high pressure switch that allows the Gemini pump to switch into high pressure mode for live floor application and warning light letting you know that you are in high pressure mode. Console comes equipped with a warning beeper to ensure you are in high pressure mode MOBILE POWER VANE PUMPS / REFUSE 15  Vane Pumps FleetPride carries a complete line of Vane Pumps by these manufacturers: Featuring a complete line of replacement Vicker® and Denison® vane pumps, FleetPride offers a large selection of balanced rotor vane pumps that directly interchange with Vickers® and Denison®. With a variety of displacements, mounting flanges and output shafts, these pumps have grown to be a mainstay in both mobile, industrial & refuse applications. These Denison vane type units come in many sizes and configurations. They are seen in refuse equipment where flow is electronically controlled to gain maximum efficiency for both the hydraulic system and fuel economy.  Refuse Systems PT6 / PT7 Series Single Section Vane Type These EVO vane type units come in many sizes and configurations. They are seen in refuse equipment where flow is electronically controlled to gain maximum efficiency for both the hydraulic system and fuel economy. This type units is commonly found on commercial and residential front and rear loaders with single hydraulic systems. EVO PT6 / PT7 Series Tandem Section Vane Type The PT6 and PT7 series are common on many of today’s refuse hydraulics systems; tandem units provide the ability to operate (2) independent hydraulic systems with one pump. These type units are seen on automated side loader refuse vehicles where two different flow rates are required for the packer and grapple arm. The flows are electronically controlled to provide constant flow to each hydraulic system to maintain efficiency for the hydraulic system and provide optimum fuel ecomony. EVO Refuse Features:  Rust resistant coated; noneed for paint  Bi-rotation; simplifying field adjustment  Longevity and reliability; trouble free operation  Compatible and interchangeable with most major manufacturers  Highest quality material available globally Gear Products Features:  Heavy duty roller and sleeve bearing designs  Pressures up to 3500 PSI  Doweled and high strength cast iron construction  Wide range of porting, mounting, and shaft options  Pressure balanced wear plates for high pump efficiency  Unloader, dry valve, speed sensor and electronic control options Versa-Pak Refuse Flow Control/Unloader: This system allows a preset amount of flow to the hydraulic system with the excess flow being returned to tank; this function protects the system’s main relief valve from being flooded. In addition, the priority type pressure compensated flow control minimizes heat generation by returning unused oil back to tank at only a few hundred PSI more than system pressure. Bushing Series 257 and 360 series These two are becoming more popular in the refuse market; bushing units typically have higher pressure ratings and longer life. Many are used today on front and rear loaders and also on automated side loader applications. Typically these are used in unloader applications where manifolds equipped with solenoids turn the system on and off. PEK/2100 and PEL/5151 Series These two fit a variety of applications in the refuse industry, designed with both side and rear ports, SAE-B 2&4 bolt mounting flange, Bi-Rotation and setup for use as a pump or motor providing versatility for uses in many application. Commonly seen in refuse roll-off, live floor, small and large rear loaders, recovery vehicles, container haulers and many other utility type vehicle applications. CH-640 and CH-512 Series These two have been specifically designed for the refuse truck market. The CH Series pumps are made of high strength cast iron and alloy steel incorporating Permco’s rugged and dependable gear pump design. CH pumps are pad mounted with double 1-1/8 inch drive shafts and large port end cover with 1-1/2 inch NPT inlets and a choice of 3/4 inch or 1 inch O-ring outlets. Unloading System The unloading system limits the flow to the system while in use to prevent hydraulic over-speeding. While in the off mode, the flow is diverted back to the tank at low pressures to control horsepower losses. Remote Mounted Relief Valves AZ5514J-100-25 or AZ5514J-100-32: Come with 1” NPT ports and is available with either 2500 or 3200 PSI maximum settings, and is field adjustable. Dry Valve System The dry valve system incorporates an air operated dry valve which permits hydraulic operation while the vehicle is in motion, and reduces fuel consumption during the off mode and eliminates heat build-up associated with “live” systems in the on mode. The 997-01238 can also be incorporated with either the dry valve or unloading system to futher protect the hydraulic system. 16 MOBILE POWER INDUSTRIAL PUMPS / MOTORS  Pumps & Motors For Mobile And Industrial Applications  Roller Bearing Pumps & Motors Series: 2100/3000/3100 Gear Width  Construction Equipment  Refuse Equipment  Mining Machinery  Agricultural Equipment  Oil Field Equipment  Industrial Equipment  Forestry Equipment * Motor specifications are given @ 1000 RPM and @ 2000 PSI. ** Consult Permco on these gear sizes. *** 2000 RPM maximum on motors. # The information shown represents the maximum # continuous operating conditions. + Maximum 3000 RPM for 5151 series.  Sleeve Bushing Pumps & Motors Series: 5000/5100/5151 Series: 7500/7600 Series: P124 Gear Width Series: P197 Tandem MOBILE POWER PISTON PUMPS / MOTORS 17  Piston Pumps & Motors PAVC Series This hydraulic pump is a Bent-Axis type pump with fixed displacement, developes under the design of spherical head pistons. This design is high performance and extremely efficient. This hydraulic pump is a NEW GENERATION pump for the Global Auxiliary Power Market. Because of the high torque requirements, this pump comes with an ISO 7653 DIN mount. All global PTO manufacturers offer this output option. PN Description 5041806 FR 5.5 (20) RIGHT ROTATION, UN THREAD 5041906 FR 5.5 (20) LEFT ROTATION, UN THREAD 5042006 FR 8.4 (30) RIGHT ROTATION, UN THREAD 5042106 FR 8.4 (30) LEFT ROTATION, UN THREAD 5042206 FR 10.4 (40) RIGHT ROTATION, UN THREAD 5042306 FR 10.4 (40) LEFT ROTATION, UN THREAD 5042406 FR 15.8 (60) RIGHT ROTATION, UN THREAD 5042506 FR 15.8 (60) LEFT ROTATION, UN THREAD 5042606 FR 20.8 (80) RIGHT ROTATION, UN THREAD 5042706 FR 20.8 (80) LEFT ROTATION, UN THREAD 5042806 FR 28.9 (110) RIGHT ROTATION, UN THREAD 5042906 FR 28.9 (110) LEFT ROTATION, UN THREAD XA Series Pumps - 6 Models Features:  Flows from 1.1 to 3.84 cu.in. (18 to 65 cc)  5075 psi (350 bar) continuous working pressure  5800 psi (400 bar) peak pressure  maximum speed from 2,300 to 2,900 rpm  Avialable in S.A.E & DIN  Change of direction of rotation by simply  changing a fitting TXV Pumps - Variable Displacement These are intelligent pumps! With variable displacement and pressure-flow control -called Load Sensing, they automatically regulate to give just what is needed for each movement. Specifically designed for the needs of the truck hydraulic market, the TXV pumps are particularly attractive solutions for applications in loading cranes, forestry cranes, refuse vehicles, salt spreaders and snow and ice equipment, and construction equipment vehicles. Extremely compact in size to allow direct flange mounting on engine PTOs or gearbox PTOs, TXV pumps are available in 7 models from 40cc to 150cc maximum displacement MA Piston Motors  Available in displacements from 10cc to 180cc  MA motors are suitable for all the main fixed  and mobile applications.  MA series motors are suitable for intensive  long duty requirements.  Designed for both mobile and industrial installations.  Availible in S.A.E. variable volume piston pumps Parker® PAVC and PVP Variable Displacement Piston Pumps are available in several displacement sizes and have a range of options to suit your particular application controls for pressure compensation, load sense, horsepower limiting and load sensing are also available. Housings are built from high strength cast iron. Sealed bearings, replaceable port plate, two-piece pump design, as well as many other features makes the PAVC pump a great choice for operational cost effectiveness and return on investment (ROI). Pump Features:  High strength cast iron housing  Built-in Supercharger  High speed capability  3000 rpm/2600 rpm PAVC100  Sealed shaft bearing  Two piece design for east of service  Cartridge type controls - field changeable  Replaceable bronze clad port plate  Air bleed standard for quick priming  Hydro-dynamic cylinder barrel bearing  Thru-shaft PAVC100 only  Full pressure rating on water glycol fluids  Pump case and shaft seal  Filter and/or cool drain line - 100 psi maximum Controls Features:  Pressure compensated  Load sensing  Horsepower - torque limiting  Horsepower and load sensing  Remote pressure compensated  Adjustable maximum volume stop  Electro-hydraulic pressure  Electro-hydraulic flow & pressure - Servo control  Low pressure standby The PAVC Piston Pumps are ideal for many mobile applications with operating pressure up to 3000 psi. These compact pumps feature an integral inlet boost pressure that results in excellent high self priming speed capability. PAVC Driven Pump Performance Information Displacement Series 33 cc/r PAVC33 38 cc/r PAVC38 65 cc/r PAVC65 100 cc/r PAVC100 Max. Outlet Pressure 3000 psi 3000 psi 3000 psi 3000 psi Rated Drive Speed 3000 rpm 3000 rpm 3000 rpm 2600 rpm @ 2000 rpm & 3600 psi Flow Input Horsepower 16 gpm 33 hp 18 gpm 36 hp 33 gpm 66 hp 53 gpm 108 hp 18 MOBILE POWER MOTORS  Motors Char-Lynn motors are extremely reliable, compact, and have tremendous power density. They provide a way to meet many needs for cost-effective power transmission requirements. Multiple motors can be driven by a single power source (pump) and controlled using a wide array of valves and variable displacement pump controls. Motors can even be configured with electronic sensors to provide digital feedback for sensing both motor direction and output speed. Motor options features include:  Displacement size (cubic inches or cc’s per revolution)  Output shaft size and type  Mounting flange type  Porting interface  A wide selection of special features such as integrated brakes,  sensors, integrated cross-over relief valves, 2-speed capability,  manifold valve packages and environmental protection suited for  corrosive environments. H Series Designed for medium duty applications, the H-Series Motors use industry-proven spool valve technology, combined with state-of-the-art gerotors. In addition, a wide variety of mounting flanges, shafts, ports and valving options provide design flexibility. Direction of shaft rotation and shaft speed can be controlled easily and smoothly throughout the speed range of the motor, and equipment can be driven direct, eliminating costly mechanical components. Features:  High efficiency  Powerful compact package  Design flexibility  Extended, leak-free performance H Series S Series 2000 Series S Series 2000 Series The popular Char-Lynn 2000 Series Disc Valve Hydraulic Motors provide torque up to 7500 lb-in. This proven design is reliable and durable. Eaton has added options that make the motor more flexible to use in a wide variety of applications. The integral cross-over relief valve is the latest innovation in the 2000 series motors. Features:  Three zone design for longer life and true  bi-directionality  Bearings that meet the highest standards of  the industry  Options to optimize performance in every application  Integrated cross-over relief valve option The new improved Char-Lynn S Series Motors with optimized Geroler geometry offers enhanced performance with reduced drive-running angle, while retaining the overall package size of the original S series. Design improvements include upgraded steel end cap, O-Ring section seals and optimized Geroler set. The Geroler set has precision-machined rollers in the outer ring which provide support with rolling contact between the star and ring. This improves mechanical efficiency, especially at start-up and at low speed conditions. Improvements incorporated into the latest S Series motor provide reliable leak-free performance and smooth operation at start-up conditions. Features:  Constant clearance Geroler design  Three moving components (gerotor, drive, shaft)  Optimized drive running angle  Three-zone pressure design (inlet, return and case)  Variety of displacements, shafts and mounts The Parker line of Low Speed High Torque (LSHT) motors provide power and versatility at an affordable cost. Available in small, medium, and large frame models, we have you covered for most hydraulic motor application requirements. Small Frame LSHT Motor - TB Series Small Frame Accessories: Specifications: This light to medium duty motor incorporates all the features of heavy duty motors. Design features include a high pressure shaft seal so external drains are never required. Also features roller vane technology for automatic wear compensation, and full flow internal cooling and flushing. This is a very economical motor for most light to medium duty applications.  Speed Sensor  Hot Oil Shuttle  Crossover Relief Valve  Internal Relief Valve  Multiple Disc Brake Small Frame LSHT Motor - TE Series This medium duty motor has higher pressure ratings than the TB motor, for applications requiring higher torque. Robust roller bearings withstand higher side loads and are suitable for chain and sprocket shaft connections. It uses high pressure shaft seals, robust roller bearings, and high flow shaft seal cooling.  14 Displ. 45 - 390 cm3/rev (2.5 - 24.0 in3/rev)  Max. Control Pressure - 125 bar - to 1800 psi  Max. Inter. Pressure - 165 bar - to 2400 psi  Max. Oil Flow - 57 lpm - to 15 gpm  Max. Speed - 785 rpm  Max Cont. Torque - 440 Nm - 3897 lb. in.  Max. Inter. Torque - 540 Nm - 4783 lb. in.  Max Side Load - 4900 Nm - to 1100 lb. Specifications:  14 Displ. 45 - 390 cm3/rev (2.5 - 24.0 in3/rev)  Max. Control Pressure - 140 bar - to 2030 psi  Max. Inter. Pressure - 190 bar - to 2750 psi  Max. Oil Flow - 75 lpm - to 20 gpm  Max. Speed - 1000 rpm  Max Cont. Torque - 467 Nm - 4139 lb. in.  Max. Inter. Torque - 648 Nm - 5728 lb. in.  Max Side Load - 6650 Nm - to 1500 lb. Large Frame LSHT Motor - TG Series The heart of Parker’s TG Series powertrain, the torque link, is an extra heavy duty part that includes patented 60:40 spline geometry. Rugged construction throughout allows the transmission of over 13,000 lb inches of torque. The entire powertrain is continually washed in cool, high flow fluid to assure long life. Roller vanes and sealed commutator maintain high efficiency and provide smooth low speed performance. Specifications:  12 Displ. 140 - 958 cm3/rev (8.6 - 58.5 in3/rev)  Max. Control Pressure - 210 bar - to 3000 psi  Max. Inter. Pressure - 281 bar - to 4000 psi  Max. Oil Flow - 114 lpm - to 30 gpm  Max. Speed - 660 rpm  Max Cont. Torque - 1044 Nm - 9239 lb. in.  Max. Inter. Torque - 1428 Nm - 12636 lb. in.  Max Side Load - 16000 Nm - to 3597 lb. MOBILE POWER BLOWERS / PUMPS / COMPRESSORS  Blowers The P857 is a two lobe, positive displacement blower design Features:  Product Pumps Features:  Coated inner wear sleeves for leak prevention due to  anti-corrosive material  Easy to remove for maintenance or repair  Simplified assembly and easier profile setting  Specially designed for a hydraulic adapter  Twin drive shafts allow for universal bi-directional mounting  Complete cast iron body and side plates  Rotor profile with constant gap  Internal breather reduces water contamination of the oil  Durable taper lock guarantees easy assembly  Compressors P40 Oil Lubricated Piston Compressor (P40)  Dependable sliding vane action provides  low maintenance, quiet operation, and  long lasting performance  Relief valve can be adjusted to  safeguard the pump from over pressure  Optional strainers to protect the pump  from any foreign material moving through  the tank or piping  Dual shaft for clock/counter clockwise drives Features:  Unique sliding-vane pump design self  adjusts for wear to maintain flow rates  Excellent self-priming and dry run capabilities  Dual end shaft on 2,” 2.5” and 3” models simplifies installation  Blackmer mechanical seal and ball bearing construction provide  maximum reliability  Symmetrical bearing support assures even loading and wear  for longer life  Adjustable relief valve protects pump against excessive pressures  External ball bearings are isolated from pumpage by mechanical  seals to maximize bearing life and minimize contamination risk  Easy maintenance: vanes can be easily replaced without  removing pump from truck Features:  30% more air than equivalent  sized machines  The P40 is a high performance piston  compressor designed for the tank truck market  The narrow profile makes fitting inside truck  frame rails fast and simple  One of the lightest oil lubricated machines  in it’s class  Quiet operation due to heavy duty construction  High airflow helps build tank pressure V120 Oil Free Vane Compressor (SV120) Features:  Ranger Pumps, Inc. manufactures a precision built   helical gear pump for industrial applications.  The capacity range is available  from 25 GPM to 360 GPM and pressures  to 125 PSI.  Ranger Pumps are designed to use as  low speed pumps for both low and high  viscosity liquids.  Ranger Pumps & all parts are directly  interchangeable with Roper® Pumps & Parts. Roper® is a registered trademark of Roper Holdings, Inc. Ranger, Inc. is not affiliated with Roper Pump Company Features:  Highest air flow in it’s class  The SV120 is designed for  today’s tank truck market  High air flow mean faster turnaround,  and more load per month  “Drop-in” design, no need to change  existing pipe work  Quiet operation  Full range of accessories available 19 Features:  Available for 3648, 3748 & 3848  Intergral Bi-Directional Relief Valve  Same performance as our proven 3600 Series  Direction relief valves  Easy-to-maintain design  Torture tested  Life exceeded 12,000 fully reversed cycles Not all products available at all Branch locations. 20 MOBILE POWER VACUUM PUMPS / COOLERS  Vacuum Pumps FleetPride carries the leading manufacturers in the vacuum pump and oil cooler lines. Rotary Vane Vacuum Pump RCF500 Rotary Vane Vacuum Pump Fruitland’s 500 Series pumps are the most widely l used throughout the industry. The 500 series pumps use less oil than any other rotary vane pump in the industry. HXL Series II Vacuum/Pressure Pumps Pump Features:  Achieve minimum 27” Hg (Intermittent)  Precise machining and sssembly  Heavy duty bearings  Viton oil deals for longer dervice life  Kevlar vanes are heat dtablilized and  machined with exacting tolerances for  superior ruggedness and durability  Easy to service  Superior pump life Our Challenger Series pumps are designed and built with the customer in mind resulting in dependable, high performing pumps that are easy to install, operate and service. As the only industrial grade rotary vane vacuum pump designed, built and supported in the USA we are committed to also being the best pump period. Superior cooling for extended operations in severe conditions:  Proven crash protection allowing all major components  to survive a catastrophic failure  Oversize heavy duty roller bearings  ensures more drive options  Precision pinned end plates for  exact reassembly alignment  High strength castings poured in the USA  High temp Teflon oil lines allow  for visual oil flow inspection  Remote mount 5 quart clear  oil tank for consistant oil level monitoring  Four point automatic lubrication system  Liquid or fan cooled versions of each model Not all products available at all Branch locations.  Hydraulic Oil Coolers Frame Mounted Cooling HydraFLOW™ is designed and assembled as a complete, easy to install package featuring:  ProveMaximum efficiency from hydraulic fan system  Minimize filter damage with filter bypass valve  Preventable oil spillage with quick, top mounted filter  Hidden breather reduces water contamination  Radiator bypass valve and cartridge style relief valve  Large sight glass SS 675 Behind-Cab Unit The SS675 behind-cab unit is mounted behind the cab and across the frame rails, keeping the unit completely free from road debris. This unit is a powerhouse, boasting twice the capacity of our frame mount models. This allows you to drive higher horsepower applications like bulk feed trailers, VAC pumps and pneumatic blowers. SS675 Features:  Strong Design: Stainless steel construction ensures great looks and long life. Unlike steel units, does not rust and is easily shined to keep your trucks looking top-of-the-line.  Heavy Duty: Our most powerful model, suitable for the toughest and most demanding mobile hydraulic applications.  “No-Drill” Optional Mounting Kit: Instead of drilling into the frame rails, mount your unit instead with an optional set of clips. Just as strong as drilling, these clips make the unit easier and faster to install and don’t compromise the integrity of your frame. Additional electric and hydraulic models available, ask for details. Not all products available at all Branch locations. MISCELLANEOUS 21  Line Filters  Temperature Controls Filter Assemblies & Filter Carts RoadWatch® uses the same state-of-the-art infrared sensing technology employed in heat-seeking missiles to constantly measure and report actual road surface temperatures. RoadWatch will accurately sense a 1° change in road surface temperature in one-tenth of a second. And, the early warning system alerts the driver when the road surface temperature dips to 37° or below. Using state-of-the-art infrared sensing, RoadWatch was originally developed to assist highway and public works departments in determining when and where to apply road treatment chemicals. Thousands of RoadWatch systems are already in use throughout North America. Using its unique early warning capabilities, city and state highway departments and airports, rely on RoadWatch to tell them when to treat road surfaces before hazardous driving conditions appear. RoadWatch® DC-1 We carry a complete line of filter carts and filters that feature easy-to-read filter condition indicators that help reduce the possibility of contamination in hydraulic systems. Spin-off throw-away elements make replacements fast and easy. Filters are a vailable in external or tank-mounted models.  Valves & Fittings Complete lines of all fittings and quick disconnects and hydraulic hose fittings in stock and special order is available. Infrared deployment control scans the road surface temperature, then automatically disperses de-icing and granular/pre-wet traction agents. The DC-1 is designed to be connected to existing electronic spreader controls. Three output channels control 3 spreader functions. Each channel has programmable temperature limits. Accessories:  12 volt quick connect power cables  Suction cup window mount  Sensor mounting brackets for frame, behind sleeper, and large tubes  Mini C mount for trucks or cars  Display mounting bracket or pedestal  Mirror display mounting or sensor mounting available  Clutch Pump Service Parts  Test Equipment Wide variety available. Complete line of clutch pump parts and accessories available. BR549 Clutch Pump Bracket for 2 bolt “A” mount 999-00956 Clutch Pump Switch Kit *After burnishing, see Owner’s Manual. 512010 AA Groove Clutch 120 lb. ft.* 520226 6 Groove Type K Serpentine Clutch 120 lb. ft.* 515376 8 Groove Type K Serpentine Clutch 120 lb. ft.*  Tail Gate Cylinders Full line of 4, 6, and 8 inch stroke tail gate cylinders available. Call for details. 22 MOBILE POWER CONSOLES / CONTROLS  Consoles/Hoist/PTO Controls VPHPV The Apsco engineering team seeks to consistently deliver an outstanding product of unsurpassed quality and performance. Custom consoles designed to your specifications are available. Not only can Apsco put any valve or switch in the console, but they can also add your own company’s logo.  Dump Pump Air Actuator Features:  Simple installation  Compact - no exposed moving parts  Cost effective  Problem free! VPAS-1 Hoist And PTO Control This hoist and PTO control in one unit is available with console and manual PTO kick out. Console with tail gate valve is also available. Retro Fits: Hydraulic pump/valve combinations, commercial, Permco, Muncie, Apsco’s patented self centering design.  Direct Mount Cylinders Features:  1 piece  Easy installation  No subassembly required  No exposed moving parts  Proportional control  Cycle tested - over 1 million cycles  Revolutionary anti-bind technology (patent pending)  Custom designed to fit most  most major hydraulic valves C-3800-DM VPHVC-TC-8/13 VTS-1 & VTS-2 VTS-1 is a spring to neutral 3-position VTS-2 is a 2-position, 4-way valve  Lift Axle Accessories 4446 All in one filter, regulator and lubricator  Pneumatic Actuators VE-2 Electric over air, 4-way, 2 position solenoid valve Features:  2.5” to 8” bore, steel, aluminum or composite tubing  Available bearing supports maximize piston rod durability  High tensile steel rods - plated for corrosion resistance  Low temperature seals  Rod wipers standard for contaminant resistance  Available in any practical stroke  Standard sizes available or custom made to specifications  Tail Gate Lock Kit Features:  2 1/2” and 3 1/2” bore  6” and 8” stroke  Electric and  over air available VL-5-ES Electric or manual 5/2 function, 4-way valve VX-4 Push-Pull, 2 position valve, 5/2 function, 4-way valve function, 1/4” NPT ports, CV = 1.5 Adjustable Pressure Regulator 13 SCFM @ 100 PSIG, rated pressure range. 1 to 125 PSIG, compact design, 1/4” ports. V-44-AP-SR Air pilot spring return valve, 5/2 function, 4-way valve function, 1/4” ports. CONSOLES / CONTROLS 23 MOBILE POWER  Consoles & Stackable Valves - vm series Custom Swivel Pedestals These valves control pneumatic or hydraulic directional control valves on industrial equipment from a remote location. Flexibility of the system with the use of bent handles allows for the customization of consoles for ideal mounting requirements and ease of operation. Their compact size makes them well suited for today’s mobile equipment, while common inlet and exhaust ports simplify plumbing when assembled in banks. For Use With VM Air Control Valve  1 - 100 Proportional control  Ability to stack valves into multiple  banked packages  Various handle bends for flexible installation Handles Available In Straight or Angled 20° - 35° - 45° - 55° VM-8 Neutral detent Features: VM7-2B2020  Easier installation  Patented swivel lock design  Durable powder coating VM-9 VM-7 3 position detent VM-11 1 off center detent Features:  13” console available for up to three bank valves  1-100 proportional control  Ability to stack valves into multiple banked packages  Various handle bends for installation flexibility  Straight, 20°, 35°, 45° or 55° handles available VM-7 VM-10 2 bank with console Quad position valve  Gear Pumps & Motors  Directional Control Valves Series 40 Series 50 Rated to 3000 psi. Spline or keyed shafts, Series 60 side or rear porting, dual rotation available on standard models. Pressure balanced loading plates on either side of gears for Series 53 maximum efficiency. Series 40 - SAE A - 2 bolt mount - rated to 17.5 gpm 6 sizes: .5 - .75 - 1.00 - 1.25 - 1.50 and 1.80 in3/rev Series 50 - SAE B - 2 bolt mount - rated to 44 gpm 7 sizes: 1.52 - 1.95 - 2.32 - 2.74 - 3.30 - 3.80 and 5.20 in3/rev Series 60 - SAE C mount - rated to 90 gpm 6 sizes: 4.05 - 5.15 - 6.15 - 7.15 - 8.15 and 9.25 in3/rev Series 53 - SAE B mount - displacements same as Series 50. Dual tandem body pump in single rotation only. Operates as 2 separate sections, combined sections or w/common inlet, and 2 outlets supply flow to 2 separate systems. Series 50G - SAE C mount - planetary gear reducer for high torque at low speeds. 4 bolt mount w/spline or keyed ouput shafts and tapered roller bearings for thrust/side load. 5.33 to 1 gearbox reduction. Series 50G Series 50PGR Series 50T 5 BANK Series 50PGR - SAE B mount - 2 bolt input mount with 7/8” spline, 13 tooth and 16/32 pitch female input spline for use with 50M or equivalent motor. 5.33 to 1 ratio. Series 50T - 3.1 step up from 540 rpm splined PTO shaft. Thru-type 6 tooth internal PTO shaft for operating. PTO driven attachment with pump in operation. Available in effective displacements. 21 tooth also available for 1000 rpm PTO. Model SS - up to 9 gpm - 3000 psi - ductile iron body. Series operation, single or multi-function unit operation. Excellent spool metering, low leakage, manual and float detents. Model AD - 15 gpm - 3000 psi - 1 or 2 Model SS spool model w/integral relief and load checks. Excellent metering, low leakage. Variety of spool and actuator options. Power beyond/closed center available. Model BA - 30 gpm - 2500 psi - 1, 2 or 3 spool valve w/excellent metering, integral differential poppet type relief and load checks. Variety of spool types/actuator options. Power beyond/closed center available. Model AD Model BA Model BC - Single spool, manually adjustable, built-in pressure compensated priority type flow control. Character/options similar to BA - open center only. C Series - CA - Manual - spring centered. CD - automatic pressure kickout. CS - solenoid operated version. Converta - Single spool standard model, open center only. Simple field conversion from 4-way to 3-way, and spring centered to manual detent. Converta Model VS2 - 20 gpm - 3000 psi Model 3 ported diverts flow to either of 2 separate circuits. Model VS4 - 40 gpm - 3000 psi Model BC 3 ported diverts flow to either of 2 separate circuits. Handle, knob, Model CA detents, spring centering, and solenoid options available. Model SD4 - 40 gpm - 3000 psi 6 ported diverts flow to either of Model VS 2 separate circuits using a single control valve. Handle, knob, detents, spring centerModel SD ing, and solenoid options available. 24 MOBILE POWER CABLE CONTROLS  Custom Cable Controls We can custom build just about any cable for automotive, heavy duty, agricultural, and industrial applications.  Button Lock  Push-Pull Standard Depressing the center button allows pushing or pulling the knob to make course travel adjustments. Routing of the flexible cable allows installation options that are not possible with solid linkages. Various output configurations are available to suit a specific application. The ordering code and technical descriptions show available choices. Features:  Push-Pull Standard industrial control cable assemblies  Shift, Brake, Clutch & Adjustable Control Cables  Locking & Non-Locking Control Cables  Wide temperature range from -65° F to +230° F  Low Friction & Low Friction EXT - Green,  Utility - Gray, Bristow - Black  Constructed of tough, durable materials  Long lasting seals  Environmentally protected Features:  Stainless steel or plated carbon steel  Plastic coated carbon steel conduit and inner member  Plastic seal & knob  Suggested end fittings - full range  Micro Adjust Push-Pull Control Head Cablecraft Ordering Codes XXX C 553 = Standard 554 = Wire Output Options T = Threaded G = Grooved Cable Length End Fittings Applications:  Load - 20 lb. maximum  Travel - 3.00” maximum  Threaded mount, friction lock, and disconnect  Normal vibration does not affect the micro adjust setting  Optional friction lock accessory available for excessive vibration  Various disconnect and output end configurations are available C = Conduit Cap - available only on solid wire & wire rope I/M All line art dimensions are represented in inches.  Cable Hardware Parts & Accessories Spring Return Kit: Convert any LD size travel threaded swivel end to spring loaded with this kit. Complete line of cable hardware parts & accessories available. Knobs & Handles: Wide variety from PTO, and mushroom, to aluminum and twist lock available. T I/M Type The Micro Adjust control heads are ideal for remote operation of a throttle, regulating valve, or other applications needing precise adjustment capabilities. Depressing the center button allows pushing or pulling the knob to make course travel adjustments. A flexible dust seal protects the internal release mechanism. Rotating the knob clockwise extends the output in the finite mode, and counter-clockwise retracts. Clevis Assemblies: Includes pin washer and cotter pin. Wide selection available. 565-553 Hydroback: Self centering in a variety of sizes. Slip Clevis: P/N: AC310 Quick Disconnect Ball Joint Connectors: Wide variety of sizes and part numbers for all of your needs. Rod End Bearings: Assorted sizes. Female Threaded Eye Ends: Assorted sizes. Strap Clamps And Shims: VLD & LD. Wire Stop & Pivot: Assorted sizes. End Rod Thread Adapters: Assorted sizes.  Wescon Remote Control Systems Look to Wescon for your remote valve applications. Wescon’s remote valve control �RVC’ has been engineered to place versatility in the hands of the installer. Our center end-locking feature is thumb activated by the “Big Red Button,” and can help your system meet OSHA standards. We also offer options such as bent levers to fit your mounting requirements, electric switches installed in the lever, or an adjustable friction device to “customize” your lever resistance. We offer a wide selection of control heads, conduit, connection hardware kits, and mounting systems, making it easy to choose Wescon for your RVC applications. Wescon’s push-pull cable assemblies are available in either groove or bulkhead configurations. Also upon request, Wescon offers a bulkhead/groove combination. MOBILE POWER CONTROLLERS 25  Spreader Control Systems Parker Spread Master Systems are designed to provide reliable application of salt and sand with remote electronics and a safer quieter cab environment.The electronics provide remote proportional control of the Feed Rate and Spinner for your V-Box or Tailgate Spreader. PSM-1500-1 Single knob spreader control with an on/off switch. PSM-1500-2 Dual knob spreader control with an on/off switch. PSM-1000 Dual knob controller with a blast function and an on/off switch. This unit removes the hydraulic from within the cab, giving you a safer and quieter environment to work in. The Parker Solution: Complete Systems from Parker remove hydraulics from the cab with remote compact electronics and easy to operate controls Superior Performance: n Total System Reliability n Safer/Quieter Environment n Improved Cab Ergonomics n Operator Friendly Systems Features: n Feed Rate Proportional Cartridge n 16 gpm n Spinner Proportional Cartridge 7gpm n Manual Overrides n Fixed Displacement Pumps n System Safety Relief in Open Center n Systems (PSM-1000 only) n Standard SAE Ports n 3000 psi Operation n Load Sense System Capability with PSM-1000  QDB Series Flow Controls are designed for applications such as spreaders where precise control of one or two functions may be required without regard to variations in load pressure. These valves are used mainly on snow removal equipment, but can also be used for other applications such as sand and fertilizer. Features: n Hardened and precision ground parts for durability n Easy to adjust knobs n Adjustable flow ranges for varying applications n Load sense option n Manual bypass option n Solenoid bypass option n Anodized aluminum body for long life DICKEY-john® Control Point® control is a resourceful three channel system that provides you the power to control granular and liquid material application rates, spinner speed, and spread width. This user-friendly unit includes an automatic override that takes control after technical failure, and in the event of ground speed sensor malfunction, the built-in ground speed simulator lets you keep spreading — even when your vehicle is stationary. LT Control™ application controller delivers precision control when you need it most. This versatile, open-loop system operates in automatic, manual, or spot spreading modes under even the harshest weather conditions. LT Control™ 26 WET LINE SYSTEM PRODUCTS MOBILE POWER  Wet Line Systems FleetPride is your premier supplier for any type of Wet Line kit.We can supply the complete wet kit, or simply the main components such as Power Take-Off Units, Pumps, Control Valves, Filters, Reservoirs (Tanks), and/or Hydraulic Hoses and Fittings. Whatever fits your needs, we are here to help with expert advice, service and quality brand components from these manufacturers: VantagePower,Parker, Chelsea, Commercial, Permco, Apsco, Muncie, and many more! VantagePower dual pressure pump is designed to operate a dump trailer and a live floor which require 2 different operating pressures: n Dual Pressure Relief: low for dump bodies, high for live floors. n Easy to switch from low to high pressure using truck air n Large 1 ½” NPT suction port in the gear housing n Three line system for continuous duty n Field adjustable relief settings n Dowelled construction n Factory installed “OEM” air shift with full metering n capabilities n Direct mount SAE “B” 4 bolt or twin shafted remote mount n with bracket n Relief valve protects the high pressure portion of the system n as well as the pump n 37 GPM @ 1800 RPM 100% factory tested n 2 year warranty  Three Way Combo Kit System Our 3-Way Combo Kit System allows you to operate multiple trailers with one tractor hydraulic system. This provides the fleet owner with greater flexibility to use one tractor for multiple purposes:  Hydraulic Reservoirs Steel & Aluminum: For continuous duty applications where high oil temperatures may be encountered. Upright reservoirs of 50 and 70 gallon capacities made from steel or aluminum is ideal for wet line systems for moving floor trailers, as well as traditional dump applications. Versions of the 55 and 75 gallons side frame mount are available. For smaller reservoir requirements, 15, 25, and 35 gallon reservoirs designed with side mount capabilities are available. Polyethylene reservoirs: Polyethylene reservoirs are constructed of rotational molding technologies. The reservoirs are available in four configurations: 50 and 75 gallon for upright and 35 and 50 gallon for side mount. PN: 1300-1 or 1300-3 3-Way Combo Kit system is designed to operate: n End Dump Trailers n Side Dump Trailers * n Walking Floor Trailers n Low Boys (1300-3 Kit) n Provides Dual pressure connections for 2000 PSI End Dumps, n or 2800 PSI trailers n VantagePower high pressure dump pumps provide high n pressure capability to 2800 PSI, along with 1”- 15 spline PN Description n output shaft for long pump life n Unique hose connections make misconnecting trailers to VPCKDP20-3LAS25-BB CCW ROTATION - BB SPLINE n incorrect ports more difficult. This results in safer operation, VPCKDP20-3RAS25-BB CW ROTATION - BB SPLINE n reduces the possibility of End Dump cylinder separations from n over pressurizing telescopic cylinders HP Dump Pump 5.1 in. - ORB Ports, n Hose connections clearly marked on Coupler Mounting Bar 2.5-3K Relief with air shifter n Operator controls all trailer functions from inside the cab Note: Cab air controls selected separately n with air controls get the ad-vantage today! ® VP PN Pneumatic Air Controls Description VPHPV HOIST - PTO VALVE VPHPVC-8 VALVE W/ 8” CONSOLE VPHPVC-T-8 VALVE W/ 8” CONSOLE & TUBING VPHPVC-13 VALVE W/ 13” CONSOLE VPHPVC-Y-13 VALVE W/ 13” CONSOLE & TUBING VPHPVC-M-Y-13 VALVE W/ 13” CONSOLE & TUBING - NO KICKOUT VPHPVC-TG-8 VALVE, HOIST, PTO, TAILGATE 8” CONSOLE VPHPVC-TG-13 VALVE, HOIST, PTO, TAILGATE 13” CONSOLE VPHPVC-HP-13 VALVE, HOIST, PTO, HIGH PRESSURE 13” CONSOLE VPHV HOIST VALVE hydraulic gear pumps: Pneumatic air controls: VantagePower offers a complete line of pneumatic controls and pneumatic cylinders for hydraulic valves as well as, stackable feathering controls to operate the valves including pedestals, consoles, and tubing kits. Whether you need standard or custom designed controls, VantagePower can provide you with what you need. VantagePower offers a complete line of pumps from 3 gpm to 40 gpm. Made of cast iron construction, precision roller bearings, low friction bushings, wide range of mounting options, and porting. Pumps and motors are available as single or multiple units. VP PN ® Hydraulic Gear Pumps Description P20 SERIES P20A396JEAF12-65 7/8 - 13 spline side & rear port s.a.e. P20A327JEAF15-65 7/8 - 13 spline side & rear port s.a.e. P20A396JEAL17-65 7/8 - 13 spline side & rear port s.a.e. P20A346JEAL20-25 7/8 - 13 spline side & rear port s.a.e. P51A346YRYL17-65 7/8 - 13 spline side & rear port N.P.T. P51 SERIES P51A346YRYL20-65 7/8 - 13 spline side & rear port N.P.T. P51A346YRYR22-65 7/8 - 13 spline side & rear port N.P.T. P51A346YRYR25-65 7/8 - 13 spline side & rear port N.P.T. P51 SERIES WITH RELIEF P51A346YRYL17-65RV 7/8 - 13 spline with built in relief P51A346YRYR22-65RV 7/8 - 13 spline with built in relief DUMP PUMPS: VP PN VPC-101-25-Z-MS-25 Dump Pumps Description Remote mount twin shaft VPC-102-25-Z-L-MS-25 DIRECT MOUNT LH VPC-102-25-Z-L-AS-25 DIRECT MOUNT LH with air shift VPC-102-25-Z-R-MS-25 DIRECT MOUNT RH RESERVOIRS: VantagePower offers a complete line of reservoirs from 7 to 75 gallon capacity. All are heavily constructed out of aluminum, steel, or poly materials. VP PN Reservoir Description Aluminum 50-A-UR-O 50 GALLON upright aluminum 50-A-SM-O 50 GALLON SADDLEMOUNT aluminum 70-A-UR-O 70 GALLON upright aluminum Steel 50-S-SM-O 50 GALLON SADDLE MOUNT STEEL 50-S-UR-O 50 GALLON upright Steel 75-S-SM-O 75 GALLON SADDLEMOUNT STEEL 27 ® MobilePower Contact your local FleetPride location or FleetPride Mobile Power toll free at 888-338-5352 or fax 203-287-3720 for availability and technical support. HYDRAULIC COMPONENTS V3-1.2014 www.fleetpride.com
© Copyright 2024 Paperzz
