ANNUAL REPORT 2010 Impresum Title: Annual Report of MEFSB - Education, Science and Research Editorial Board: Dražan Kozak, Slavonski Brod Marija Živić, Slavonski Brod Ivica Kladarić, Slavonski Brod Tomislav Šarić, Slavonski Brod Goran Šimunović, Slavonski Brod Pero Raos, Slavonski Brod Todor Ergić, Slavonski Brod Vlatko Marušić, Slavonski Brod Editor-in-Chief: Dražan Kozak Technical Editing, Design & Computer Typesetting: Milan Kljajin Address of Editorial Board: Strojarski fakultet Trg Ivane Brlić-Mažuranić 2 35000 Slavonski Brod, Croatia e-mail: [email protected] Translation: Željka Rosandić Publisher: Mechanical Engineering Faculty in Slavonski Brod (MEFSB), Croatia Annual report published yearly Circulation: 300 issues Printed in Croatia Print: Grafika, Osijek UDK 378.6(497.5 Slavonski Brod)=111 ISSN 1847-7429 Key title Annual report of MEFSB Abbreviated key title Annu. rep. MEFSB Volume II Number 1 Pages 1-180 ANNUAL REPORT 2010 Contents Preface 3 Introduction Josip Juraj Strossmayer University of Osijek Mechanical Engineering Faculty in Slavonski Brod Study Programmes Students Scientific Activities Cooperation with the Economy Management of Faculty 4 4 5 7 8 9 12 Organization and Employees Department for Mechanical Design Department for Production Engineering Department for Materials Engineering Department for Industrial Engineering Chair for Common Subjects 13 13 14 15 16 17 Study Programmes Undergraduate Study: Mechanical Engineering Graduate Study: Mechanical Engineering Postgraduate Specialist Study: Development of Products and Technologies Postgraduate Doctoral Study: Mechanical Engineering 18 18 23 32 Scientific and Research Projects Submitted New Projects Accepted New Projects Junior Researchers Defended PhD Theses University Specialists of Mechanical Engineering 46 57 64 66 68 76 Activities of Departments Department for Mechanical Design Department for Production Engineering Department for Materials Engineering Department for Industrial Engineering 79 79 86 91 95 35 International Collaboration International Projects Visits to the MEFSB within the CEEPUS Funding Sheme Signed Agreements on International Collaboration International Students Exchange Erasmus Mobility Programme 99 99 109 111 117 119 Other Events Power Plant Symposium for Students in Slavonski Brod English in Action at MEFSB: Business Communication Skills Lectures held at MEFSB Festival of Science 2010 Visit to the European Centre for Renewable Energy in Güssing Conference on Engineering Research 120 120 123 126 129 130 133 1 ANNUAL REPORT 2010 Contents Publications Published Books Annual Report of MEFSB for 2009 Tehnički vjesnik - Technical Gazette Strojarstvo - 35th anniversary of J. J. Strossmayer University of Osijek 134 134 137 138 140 Organization of Conferences PLIN 2010 (GAS 2010) TEAM 2010 (Technics, Education, Agriculture & Management) Strojarski izazov (Mechanical Engineering Challenge) ICMEM 2010 142 142 143 144 145 Students’ Activities Study Visit to SAME DEUTZ-FAHR Žetelice d.o.o. in Županja Study Visit to TŽV GREDELJ d.o.o. in Zagreb Sports Activities Huawei Summer Camp 2010 146 146 147 148 149 Social Activities Visit to Zagreb and Krapina Advent in Vienna 150 150 152 In Memoriam 153 Published Results 155 The Last Archived 178 Map of Slavonski Brod 179 2 ANNUAL REPORT 2010 Preface Dear Readers, you hold in your hands the second edition of the Annual Report on education, scientific and research activities of the staff of the Mechanical Engineering Faculty in Slavonski Brod (MEFSB), J. J. Strossmayer University of Osijek in 2010. After the first enthusiastic edition which was warmly welcomed by our colleagues and friends abroad, the second one is more comprehensive, encompassing also the data on the study programmes, cooperation with industry and social events. The basic idea of this Report is still the same as before, i.e. to present educational and scientific activities of our departments, introducing you with the new equipment in our laboratories, the projects for industry, the published papers, the important events and realised international cooperation in the last year. I would like to thank our Vice-Dean for Science – Prof. dr. sc. Marija Živić who did once again great work collecting and processing all important information and preparing them in publishing-ready format. Many thanks go to our Heads of the Departments who presented the research activities of their Chairs. Prof. Željka Rosandić helped us to translate all the material into English and Prof. dr. sc. Milan Kljajin designed the final layout of the publication. Furthermore, I sincerely hope that you will find some interesting data in this brochure for yourself and if you get some idea on how to improve the cooperation with our Faculty, the main aim of this publication will be fulfilled. As the Dean who initiated and further promoted this idea, I would like to express my deepest satisfaction with the whole project that will definitely become a tradition at the Mechanical Engineering Faculty in Slavonski Brod. In Slavonski Brod, May 2011 Prof. dr. sc. Dražan Kozak 3 ANNUAL REPORT 2010 Introduction Josip Juraj Strossmayer University of Osijek Mechanical Engineering Faculty in Slavonski Brod Mechanical Engineering Faculty in Slavonski Brod is a part of Josip Juraj Strossmayer University of Osijek that has 11 faculties, 5 university departments, 1 Academy of Arts, 2 Student Centres and 1 City and University Library (which makes up a total of 22.340 members of the university academic community). - Mechanical Engineering Faculty in Slavonski Brod is an independent legal subject located at the main square in Slavonski Brod which is named after our famous author of children's books Ivana Brlić Mažuranić. - Mechanical engineering study programmes started at this Faculty in 1962 and next year we shall celebrate 50th anniversary of mechanical engineering study in Slavonski Brod, and therefore Fourth Conference TEAM 2012 will be organised in Slavonski Brod by the International TEAM Society: University of Applied Sciences of Slavonski Brod, Mechanical Engineering Faculty in Slavonski Brod and GAMF Kecskemét College, Hungary. Furthermore, a rich programme will be arranged during the whole year. - The courses were a part of the Centre for part-time education of Polytechnic of Zagreb. After the integration of Polytechnic with Mechanical Engineering and Naval Architecture Faculty in 1967 into Faculty of Mechanical Engineering and Naval Architecture (FSB) in Zagreb, the Centre for part-time education in Slavonski Brod continued to function as FSB Centre for Mechanical Engineering Study in Slavonski Brod. When J. J. Strossmayer University of Osijek was founded in 1975, the Centre for Mechanical Engineering Study became a constituent part of the University. In 1979, Mechanical Engineering Faculty was founded as a part of 'Mechanical Engineering Institute' of Đuro Đaković factory, and since 1991 Mechanical Engineering Faculty is an independent scientific-educational institution which is the constituent part of the J. J. Strossmayer University of Osijek. In 2010, we celebrated 35th anniversary of J. J. Strossmayer University of Osijek and on this occasion a special issue of Strojarstvo was published (Vol. 52, No 2) with scientific and professional papers written by professors and assistants from the University (2/3 were from Mechanical Engineering Faculty in Slavonski Brod). Today, the Mechanical Engineering Faculty has 30 members of academic staff with PhDs (11 full professors, 10 associate professors, 2 assistant professors, 7 senior assistants), 4 members holding teaching titles (senior lecturers/lecturers), 9 scientific researchers/ assistants and 10 other employees (associates, laboratory technicians, system engineers). The ratio of the teaching staff to the number of students is adequate for different study programmes according to the Bologna process. 4 ANNUAL REPORT 2010 Study Programmes There are different programmes at Mechanical Engineering Faculty in Slavonski Brod: university undergraduate study programme and university graduate study programme, as well as postgraduate doctoral study programme and postgraduate specialist study programme. University undergraduate and graduate study programme Production Mechanical Engineering (3,5+1,5 scheme) will continue up to academic year 2013/14, i.e. until the generation of 2009/10 graduates. The first generation of undergraduate study programme Mechanical Engineering (3+2 scheme) enrolled in 2010/11. University undergraduate study Mechanical Engineering lasts for 6 semesters. Upon completion of studies, student obtains 180 ECTS and student is awarded academic title: University Baccalaureus Engineer (Mechanical Engineering), (univ. bacc. ing. mech.). The dean of Faculty Prof. dr. sc. Dražan Kozak University graduate study programme Mechanical Engineering lasts for 4 semesters and there are 4 modules: Materials Engineering, Manufacturing Logistics, Mechanical Engineering Technologies, Design and Development of Products. Upon completion of studies, student obtains 120 ECTS and student is awarded academic title: Master of Mechanical Engineering (mag. ing. mech.). On 4 June 2010, a Graduation Ceremony was held at Elementary Music School "Ivan Zajc" (at Fortress Brod) for: university baccalaureus/baccalaurea engineers (27), professional baccalaureus/baccalaurea engineers (4), graduate mechanical engineers (20), mechanical engineers (8) and university specialists for mechanical engineering (3). 5 ANNUAL REPORT 2010 Since 2007/2008, there is also the postgraduate doctoral study programme (field: Mechanical Engineering) with three modules: Modern Manufacturing Processes, Modern Production Management, Design and Numerical Modelling of Products. This doctoral study lasts for 6 semesters. Upon completion of studies, student obtains 300 ECTS and student is awarded academic title: Doctor of Science (dr. sc.). There are 25 candidates at the postgraduate doctoral study (13 candidates won their master's degree, 13 won their doctor's degree). Since 2006, there is also the postgraduate specialist study programme: Development of Products and Technologies (field: Mechanical Engineering) with four modules: Materials Engineering, Modelling and Numerical Analysis of Constructions, Application of Manufacturing Processes, Production Management. Upon completion of studies, student obtains 90 ECTS and student is awarded academic title: University Specialist of Mechanical Engineering (univ. spec. mech.). There are 13 candidates at the postgraduate specialist study (7 won their degree). The vice-dean for education Prof. dr. sc. Ivica Kladarić The Graduation Ceremony for 65 mechanical engineers was held on 4 June 2010. There were 27 university baccalaureus / baccalaurea engineers, 4 professional baccalaureus / baccalaurea engineers, 20 graduate mechanical engineers, 8 mechanical engineers and 3 university specialists of mechanical engineering. During this ceremony, the best students (Dino Bučević-Keran, Mladen Radman, Matej Štajduhar, Marinko Ošap and Ivan Podgorski) received Dean's Award, and the best graduates (Denis Sabo, Sara Havrlišan, Danijel Kutičić and Marko Zovko) received award from Holding "Đuro Đaković". The award for best graduate of generation was given to Danijela Pezer. 6 The vice-dean for development and cooperation with the economy Prof. dr. sc. Tomislav Šarić, the best graduate of generation Danijela Pezer and CEO of Holding "Đuro Đaković" Zdravko Stipetić ANNUAL REPORT 2010 Students Currently, there are 720 students at the Mechanical Engineering Faculty in Slavonski Brod (including all programmes: university undergraduate study, university graduate study, and the study programmes before the Bologna process). Out of 32 generations of enrolled students, the following graduated: 545 at university undergraduate studies, 429 at professional undergraduate studies (before the Bologna process). There are 48 students with title: Baccalaureus Engineer (university and professional) and 28 Masters of Mechanical Engineering. The 6th generation according to the Bologna declaration was enrolled in 2010/11 and for the first time, matriculation was based on the results of State Matura exam. Darko Damjanović, student of Mechanical Engineering Faculty in Slavonski Brod, was one of the top (11) students in Croatia who won a scholarship from one of the biggest high-tech companies in the world: Huawei Technologies, China. This scholarship was part of the project "Huawei Summer Camp 2010" organized by the Chinese company Huawei Technologies and Office of the President of the Republic of Croatia. The scholarship covered all the expenses for the trip to People's Republic of China in the time period of 24 to 31 July 2010 and visit to some of the largest cities in China: Hong Kong, Shenzhen, and Shanghai (see more on the page 149). Darko Damjanović Darko Damjanović is the first on right of the President of the Republic of Croatia 7 ANNUAL REPORT 2010 Scientific Activities Professors of MEFSB are in charge of numerous research projects (international, technological, IT, etc.). Currently, there are 11 research projects, bilateral projects of cooperation with Slovenia and Serbia; and our teaching staff is involved in 5 CEEPUS projects, ERASMUS project, and IPA IIIC project that are in their evaluation stage. Mechanical Engineering Faculty is a co-organiser of several conferences (national and international). It is significant that several conferences have been held on natural gas (in cooperation with HEP Plin, d.o.o. Osijek), as well as the conferences on welding and allied techniques: "Robotization and Automation in Welding and Other Techniques" (in cooperation with Society for Welding SB and Holding Đuro Đaković). The Second International Scientific and Expert Conference TEAM 2010 (Technics, Education, Agriculture & Management) was held on 4 and 5 November 2010 in Kecskemét, Hungary. It was organized by the International TEAM Society: University of Applied Sciences of Slavonski Brod, Mechanical Engineering Faculty in Slavonski Brod and Kecskemét College, Faculty of Mechanical Engineering andAutomation, Kecskemét, Hungary. st The 1 International Scientific Conference on Manufacturing Engineering & Management ICMEM 2010 took place on 21 - 23 November 2010, in Prešov, Slovakia. Conference was organized by Department of Manufacturing Management, Faculty of Manufacturing Technologies, Technical University of Košice with a seat in Prešov, Mechanical Engineering Faculty in Slavonski Brod, Faculty of Management Czestochowa University of Technology, Poland and Faculty of Economic Sciences Valahia University of Targoviste, Romania. Fourth Strojarski izazov (Mechanical Engineering Challenge), organized by the Mechanical Engineering Faculty in Slavonski Brod and ĐĐ Montaža (from 29 to 30 April 2010), welcomed all the students and high school graduates from Slavonski Brod. The main purpose of this manifestation is to show how knowledge and experience can be successfully brought together. Mechanical Engineering Faculty is also famous for publishing, and we proudly point out 'Technical Gazette' which is the scientific–professional journal that is published together with the Faculty of Electrical Engineering and the Faculty of Civil Engineering of the University of Osijek. This journal is indexed in SCI Expanded base (from Volume 15, Number 1, 2008). Our professors are also very prolific authors with 42 books, 32 internal publications, all of which enriches the existing library holdings in our Faculty Library with a sole purpose of making knowledge more available to our students. 8 Details from unique event th 4 Mechanical Engineering Challenge, Slavonski Brod, April 29-30, 2010 ANNUAL REPORT 2010 Cooperation with the Economy The cooperation with the economy is based on the education and on solving various research-development tasks. Furthermore, professional consults and expertise can also be offered. The teachers of the MEFSB are very active as advisors to a range of businesses. They can offer scientific contribution in different development and research tasks, as well as the expertise dealing with production and product quality. Together with the Croatian Chamber of Mechanical Engineers, the MEFSB organises numerous conferences as part of life-long learning. Some projects of the cooperation with economy realized in 2010 and earlier are given in continuation. Project title: Numerical analysis of structures Project coordinator: Prof. dr. sc. Dražan Kozak Short description: Technical report includes results of numerical investigation of elasticplastic behaviour of pipelines between overheater - overheater chamber, using finite element method. Associate: Josip Sertić, dipl. ing. stroj. Project title: Testing the durability of pressure regulator membrane Project coordinator: Prof. dr. sc. Pero Raos Short description: The durability of gas regulator membrane was tested. The testing was used to determine the exact time period when the membrane loses the initial properties. Project title: Technical training for heat treatment operators Project coordinator: Prof. dr. sc. Dragomir Krumes Short description: Technical training for heat treatment operators was conducted. This training encompassed theoretical, as well as practical part. 9 ANNUAL REPORT 2010 Project title: Materials testing and weld joint certification Project coordinator: Prof. dr. sc. Vlatko Marušić Short description: The following testing was performed: - chemical composition of the base metal and added material, - hardness, - mechanical properties, technological properties, bending, widening of pipes, - metallographic investigation of the structure of base material and weld. Testing is done according to the appropriate ISO/EN/ASTM Standards. Project title: Testing of shafts and choice of repair technology Project coordinator: Prof. dr. sc. Vlatko Marušić Short description: Rapid wear of elements of tribopair of oil press occurs due to almost simultaneous abrasion, adhesion, fatigue and tribocorrosion. A shaft with characteristic wear mechanisms is shown in the figure. Research results were used for the choice of parameters of welding with additional material based on Cr-Mo (for repair welding of the shaft). Characteristic wear mechanism of shaft a) abrasion; b) adhesion; c) surface fatigue; d) tribocorrosion Project title: Revitalisation of boiler plant management system Project coordinator: Mr. sc. Vjekoslav Galzina Short description: Revitalisation and optimisation of boiler plant management was done according to the needs of the company Sladorana d.d. Županja. Zahtjev sa distributora Spremnik mazuta Postrojenje za pripremu mazuta Dimnjak Limiter i selektor Mjerenje temperature dimnih plinova PID O2 PID gorivo Mjerenje protoka mazuta Regulacija protoka mazuta PID zrak Mjerenje sadržaja O2 u dimnim plinovima Mjerenje protoka zraka Ventilator Ložište Regulacija protoka zraka Mjerenje protoka Regulacija protoka plina plina Mjerenje temperature dimnih plinova nakon predgrijača vode Scheme of boiler combustion control Values (after calibration) 10 ANNUAL REPORT 2010 Project title: Measuring of vibrations on a tank Project coordinator: Prof. dr. sc. Todor Ergić Short description: Measuring of vibrations on a tank was done in order to determine their intensity. These results were used to reduce the intensity of vibrations. Project title: Analysis of the project of energy efficiency and use of renewable energy sources Project coordinator: Dr. sc. Štefanija Klarić Short description: The analysis of the project of energy efficiency and use of renewable energy sources for municipality buildings in Okučani and Stara Gradiška was performed (for the company SOLING d.o.o.). Research results show that energy efficiency has increased and CO2 emission has reduced after the renovation of buildings. a) b) Municipality building (Stara Gradiška)(now)(a) and municipality building (Okučani) (before renovation)(b) Project title: Determining the factors that caused the accident of crane DEMAG HC 240 Project coordinator: Prof. dr. sc. Franjo Matejiček Short description: Mechanical-hydraulic elements were tested and analysed in order to determine the cause of the crane accident. 11 ANNUAL REPORT 2010 Management of Faculty Dean: Dr. sc. Dražan Kozak, full prof. E mail: [email protected] tel. +385 35 493 400 mob. +385 91 446 01 01 Vice-dean for education: Dr. sc. Ivica Kladarić, associate professor E-mail: [email protected] tel. +385 35 493 453 mob. +385 91 446 01 02 Vice-dean for science: Dr. sc. Marija Živić, associate professor E-mail: [email protected] tel. +385 35 493 443 mob. +385 91 446 01 09 Vice-dean for development and cooperation with the economy: Dr. sc. Tomislav Šarić, associate professor E-mail: [email protected] tel. +385 35 448 264 mob. +385 91 446 01 03 From left to the right: Ivica Kladarić, Mirjana Senić Moškun, Dražan Kozak, Marija Živić, Tomislav Šarić The Mechanical Engineering Faculty operates at three locations: Ivana Brlić-Mažuranić Square 2 (Dean's Office, Secretary's Office, Admission's Office, Accounting Department, lecturerooms and teachers' offices), Ivan Gundulić 20A (with computer labs, tele-conference room (TCR), laboratory, library, lecturerooms and teachers' offices), and in the factory Đuro Đaković in Mile Budak (with well-equipped laboratories and lecture-rooms). The locations map is given on the page 179 12 Secretary of the Faculty: Mirjana Senić Moškun, dipl. iur. E-mail: [email protected] tel. +385 35 447 792 mob. +385 91 446 01 04 ANNUAL REPORT 2010 Organization and Employees Department for Mechanical Design Chair for Machine Parts and Design E-mail: [email protected] tel. +385 35 493 417 Ivandić, Željko dr. sc. Associate Professor, Head of Chair Kljajin, Milan dr. sc. Full Professor with Tenure Kokanović, Mato dipl. ing. stroj. Assistant Karakašić, Mirko dr. sc. Junior Researcher/Senior Assistant Baškarić, Tomislav mag. ing. mech. Assistant Chair for Mechanics and Strength E-mail: [email protected] tel. +385 35 493 417 Matejiček, Franjo dr. sc. Full Professor with Tenure Kozak, Dražan dr. sc. Full Professor, Dean Ergić, Todor dr. sc. Associate Professor, Head of Chair, Head of Department Sertić, Josip dipl. ing. stroj. Assistant Konjatić, Pejo dr. sc. Junior Researcher/Senior Assistant Damjanović, Darko mag. ing. mech. Assistant Chair for Energetics E-mail: [email protected] tel. +385 35 493 411 Živić, Marija dr. sc. Associate Professor, Vice-Dean for Science Hnatko, Emil dr. sc. Full Professor with Tenure Stojkov, Marinko dr. sc. Associate Professor, Head of Chair Zmaić, Željko dipl. ing. stroj. Assistant 13 ANNUAL REPORT 2010 Department for Production Engineering Chair for Casting and Deformation Budić, Ivan dr. sc. Full Professor with Tenure Grizelj, Branko dr. sc. Full Professor with Tenure, Head of Chair Cumin, Josip dipl. ing. stroj. Junior Researcher Novoselović, Daniel dr. sc. Senior Assistant E-mail: [email protected] tel. +385 35 493 426 Chair for Chip-forming and Polymers Raos, Pero dr. sc. Full Professor with Tenure, Head of Department Stoić, Antun dr. sc. Associate Professor, Head of Chair Pranić, Ante dipl. ing. stroj. Associate Stojšić, Josip dipl. ing. stroj. Junior Researcher/Assistant E-mail: [email protected] tel. +385 35 493 428 E-mail: [email protected] tel. +385 35 493 412 Chair for Welding and Surface Protection Samardžić, Ivan dr. sc. Full Professor with Tenure, Vice-Rector for Science, Technology, Projects and International Cooperation Aračić, Stjepan dr. sc. Full Professor, Head of Chair Klarić, Štefanija dr. sc. Assistant Maglić, Leon dr. sc. Assistant Professor Duspara, Miroslav dipl. ing. stroj. Junior Researcher/Assistant 14 E-mail: [email protected] tel. +385 35 493 440 ANNUAL REPORT 2010 Department for Materials Engineering Chair for Materials E-mail: [email protected] tel. +385 35 493 420 Marušić, Vlatko dr. sc. Full Professor, Head of Department Krumes, Dragomir dr. sc. Full Professor with Tenure Milinović, Andrijana dr. sc. Junior Researcher/Senior Assistant Rosandić, Željko dipl. ing. stroj. Assistant Chair for Heat Treatment and Tribology E-mail: [email protected] tel. +385 35 493 409 Marković, Radojka mr. sc. Senior Lecturer, Head of Chair Kladarić, Ivica dr. sc. Associate Professor, Vice-Dean for Education Pecić, Vladimir dipl. ing. stroj. Associate 15 ANNUAL REPORT 2010 Department for Industrial Engineering Chair for Process Planning and Process Control Lujić, Roberto dr. sc. Associate Professor, Head of Chair, Union representative Šimunović, Goran dr. sc. Associate Professor, Head of Department Matičević, Gordana dr. sc. Senior Assistant Čičak, Mirjana mr. sc. Assistant Mazurek, Miroslav dipl. ing. elteh. CARNet System Engineer Kolesarić, Goran dipl. ing. stroj. Laboratory Technician E-mail: [email protected] tel. +385 35 493 431 E-mail: [email protected] tel. +385 35 493 454 Chair for Maintenance and Computer Integrated Manufacturing Šarić, Tomislav dr. sc. Associate Professor, Vice-Dean for Development and Cooperation with the Economy Šimunović, Katica dr. sc. Assistant Professor, Head of Chair Galzina, Vjekoslav mr. sc. Junior Researcher/Assistant Galeta, Tomislav dr. sc. Assistant Professor Svalina, Ilija dipl. ing. stroj. Assistant Pezer, Danijela dipl. ing. stroj. Junior Researcher/Assistant 16 E-mail: [email protected] tel. +385 35 493 430 ANNUAL REPORT 2010 Chair for Common Subjects E-mail: [email protected] tel. +385 35 493 438 Miljković, Zvonko mr. sc. Senior Lecturer, Head of Chair Pavić, Zlatko mr. sc. Senior Lecturer Rosandić, Željka prof. Lecturer Novoselac, Vedran prof. Assistant 17 ANNUAL REPORT 2010 Study Programmes Undergraduate Study: Mechanical Engineering Mechanical engineering, belonging to a technical field, contains disciplines which include all phases and processes in a product service life: from idea, design and construction, technology and tools development, production planning and managing, providing services, assembling, carrying out testing, putting in operation, providing maintenance; up to recycling or ecological disposal of waste at the end of the technical or economic service life. Numerous employment opportunities of mechanical engineers have also put additional demands on their education: it is becoming necessary to gain basic knowledge of processes and methodologies to understand and define the processes of change in the chain of activities from idea to the finished product, its exploitation and recycling. These methodologies are founded both on modern theoretical models and procedures and information technology support, and in particular on the application of artificial intelligence (genetic algorithms, neural networks, and expert systems). The programme offers courses necessary to satisfy the requirements of modern manufacturing (new technologies, computer aided manufacturing logistics, information technologies, methods of product development and design, materials engineering). They will provide knowledge and skills necessary for the development of production companies in order to meet the terms, prices and quality of products and services able to compete internationally. The study is carried out at the Mechanical Engineering Faculty in Slavonski Brod. The lecturers from other Faculties of the Josip Juraj Strossmayer University of Osijek are also engaged. The duration of the study is 6 semesters. Before the lectures begin, the students can take courses in Mathematics and Physics (30 hours) to make it easier for them to understand the first year courses; or Introduction of Mechanical Engineering (15 hours) - to acquire some basic technical knowledge. In the first year (1st and 2nd semester) the students take the core subjects (mathematics, mechanics, materials and electrical engineering) necessary for the understanding of professional courses; courses in technical drawing and computer graphics and computer applications for the use of software systems and programmes in professional courses, as well as the elective course, i.e. the technical foreign language (English or German), which is required for the use of foreign technical literature. In the second year (3rd and 4th semester), the students are provided with the basic knowledge and skills necessary for independent learning and mastering the technical expertise for their own 18 ANNUAL REPORT 2010 profession (mathematics, materials, machine parts, production methods, strength of materials, thermodynamics and maintenance). In the third year (5th and 6th semester), the students take joint specialized courses necessary for the engineers of production engineering to solve problems in manufacturing and service enterprises (fluid mechanics, programming CNC machines, manufacturing machines, manufacturing processes, heat treatment, tools and appliances, automation, production planning and management, quantitative methods and theories and techniques of measurement). In addition to these joint courses for graduates of engineering, through elective courses (computer applications, pneumatic and hydraulic systems, probability and statistics, and product assembly), the students are preparing for their orientation to the graduate study. Through compulsory and elective courses and a final project in the 6th semester, the students gain the necessary width of education for practical work in the manufacturing and service companies. The undergraduate students (with achieved 180 ECTS points) may enrol (with the adequate grade point average) the graduate study programme at the Mechanical Engineering Faculty in Slavonski Brod. A student must earn at least 180 ECTS points (including the final project) to obtain an academic title: University Baccalaureus Engineer (Mechanical Engineering), (univ. bacc. ing. mech.). The programme of the undergraduate study through semesters is given below. 19 ANNUAL REPORT 2010 Semester I Course Mathematics I Mechanics I Materials I Technical Drawing and Computer Graphics Physical and Health Education I Technical Foreign Language I L E ECTS S Exam 3 2 3 3 0 1 12 3 2 3 3 2 1 14 7 5 7 8 1 2 30 M M M M M O * * * ** ** ** 3 Code number P 101 P 102 P 103 P 104 P 106 * Oral or written exam, ** Knowledge verification (program, seminary, colloquy, test) Technical Foreign Language I L E ECTS S Code number Technical English Language I Technical German Language I 1 1 1 1 2 2 O O P 307 P 308 L E ECTS Code number 2 1 1 0 1 0 P P P P 111 P 109 P 110 Course L E ECTS S Exam Electrical Engineering Materials Testing and Properties Mathematics II Mechanics II Computer Aided Preparation and Production Physical and Health Education II Technical Foreign Language II 2 2 3 3 2 0 1 13 2 1 3 3 3 2 1 15 5 3 7 6 6 1 2 30 M M M M M M O * * * * ** ** ** 4 Technical Foreign Language I I L E ECTS S Code number Technical English Language II Technical German Language II 1 1 1 1 2 2 O O P 408 P 409 Preparatory courses Physics Mathematics Introduction of Mechanical Engineering Semester II Abbreviations L – Lectures E – Exercises S – Status M – Mandatory O – Optional P – Preparatory course 20 Code number P 304 P 608 P 201 P 202 P 205 P 206 ANNUAL REPORT 2010 Semester III Course L E ECTS S Exam 2 3 2 2 4 0 1 14 2 2 2 2 2 2 1 13 5 5 5 5 7 1 2 30 M M M M M M O * * * * * ** ** 5 Technical Foreign Language III L E ECTS S Code number Technical English Language III Technical German Language III 1 1 1 1 2 2 O O P 506 P 507 Strength of Materials Machine Parts I Mathematics III Materials II Manufacturing Technologies I Physical and Health Education III Technical Foreign Language III Code number P 203 P 302 P 301 P 204 P 303 P 306 Semester IV Course Machine Parts II Maintenance Manufacturing Technologies II Thermodynamics Physical and Health Education IV Industrial practice 1) L E ECTS S Exam 2 2 4 3 0 0 11 2 2 2 3 2 5 16 5 5 7 7 1 5 30 M M M M M M * * * * Code number P 401 P 721 P 403 P 305 P 407 4 1) Industrial practice (1 month) Semester V Course Automation Quantitative Methods Fluid Mechanics Machine Tools Manufacturing Technologies III Optional courses Optional course Products Assembling Pneumatic and Hydraulic Systems Computer Programs University optional course Probability and Statistics L E ECTS S Exam 2 2 3 2 4 2 15 2 2 2 1 2 1 10 5 5 6 4 7 3 30 M M M M M O * * * * * ** 5 L E ECTS S Code number 2 2 2 2 2 1 1 1 1 1 3 3 3 3 3 O O O O O D 791 P 610 D 1025 P 505 P 513 Code number P 404 P 605 P 501 P 504 P 503 21 ANNUAL REPORT 2010 Semester VI Course Tools and Devices I Production and Operations Management Programming of CNC Machines and Robots Theory and Technique of Measurements Heat Treatment Final project L E ECTS S Exam 2 3 2 2 2 0 11 1 3 2 1 2 5 14 3 7 5 3 5 7 30 M M M M M M * * * * * ** 5 Courses offered in English Code number P203 P304 P305 P404 P501 P502 P605 Course Strength of Materials Electrical Engineering Thermodynamics Automation Fluid Mechanics Production and Operations Management Quantitative Methods I The Faculty Library 22 Code number P 602 P 502 P 603 P 512 P 754 P 720 ANNUAL REPORT 2010 Graduate Study: Mechanical Engineering The graduate study should educate the students to become the leaders of development in manufacturing industries and services striving to turn them into modern enterprises able to get readily adapted to the flexible demands of the market, application of new technologies, methods and procedures in order to compete successfully with others. Acquiring the skills to implement the new manufacturing strategies, understanding the properties and applications of new materials, new manufacturing technologies, possibilities of automation of production and its planning, the graduate students should be at the forefront of technological development in their work field. In addition to acquiring professional knowledge in their field of study and learning about the most recent developments in the world, the graduate students will also get an insight into and be prepared for the scientific-research work (defining problems, modelling processes and setting aims, using numerical and statistical methods to optimise models, ways of writing and presenting the results of a scientific-research study, etc.). The duration of the study is 4 semesters, containing 120 ECTS points and providing students with further in-depth study of certain courses. The complexity and depth of the study and the skills thus obtained enable the graduates to solve the most complex engineering tasks. The graduate student is given the academic title: Master of Mechanical Engineering (mag. ing. mech.). Graduate students (with 300 credit points, i.e. 120 earned on the graduate degree study) can enrol in postgraduate study if the grades are satisfactory or/and they have achieved outstanding results in the scientific-research work. The graduate study offers four degree programmes: ? Product Design and Development The graduate students obtain knowledge and skills for development, implementation and application of new methods and tools in creating, designing and constructing of products and developing their own scientific-research work in the product development and design. ? Manufacturing Logistics The graduate students obtain knowledge and skills necessary for conducting research, developing and applying the new models and methods in business, production, preparation of production and maintenance management. 23 ANNUAL REPORT 2010 ? Materials Engineering The graduate students are provided with the knowledge and skills needed for research and application of the new methods and processes in the materials engineering. ? Engineering Technologies The graduate students are provided with the knowledge and skills necessary for research, development and application of new manufacturing technologies. These programmes provide students with specialised knowledge necessary for solving development tasks in manufacturing companies or for further education needed for research work. The list of compulsory and elective courses by modules is given below. Product Design and Development Semester I Course Strength of Materials II Design Theory Computer Aided Design Theory of Elasticity Numerical Methods Optional courses I L E ECTS S Exam 2 2 2 2 2 2 12 2 2 2 2 2 2 12 5 5 5 5 5 5 30 M M M M M O * * * * * ** 5 * Oral or written exam; ** Knowledge verification (program, seminary, colloquy, test) Optional courses I L E ECTS S Code number Renewable Energy Sources Metal Structures Tribology of Machine Elements Heat Transfer 2 2 2 2 2 2 2 2 5 5 5 5 O O O O D 928 D 809 P 704 D 728 Abbreviations L – Lectures E – Exercises S – Status M – Mandatory O – Optional 24 Code number P 702 P 703 P 712 D 904 D 903 ANNUAL REPORT 2010 Semester II Course Ecodesign Experimental Mechanics Finite Element Method Dynamics of Machinery Optional courses II Optional courses III Optional courses II and III Evaluation Models Design and Analysis of Structures Advanced Strength of Mechanical Constructions Thermodynamic Machinery L E ECTS S Exam 2 2 2 2 2 2 12 2 2 2 2 2 2 12 5 5 5 5 5 5 30 M M M M O O * * * * ** ** 4 L E ECTS S Code number 2 2 2 2 5 5 O O D 808 P 706 2 2 5 O D 800 2 2 5 O P 405 Code number D 801 D 806 P 705 P 701 Semester III Course L E ECTS S Exam 2 2 2 2 2 0 10 2 2 2 2 2 4 14 5 5 5 5 5 5 30 M M M O O M * * * * ** L E ECTS S Code number 2 2 2 2 5 5 O O D 923 D 843 Optional courses V L E ECTS S Code number Optimization of Structures Theory of Plasticity Vibration-Acoustic Analyses Computational Fluid Mechanics Power Plants 2 2 2 2 2 2 2 2 2 2 5 5 5 5 5 O O O O O Industrial Design Numerical Modelling and Simulations Fracture Mechanics Optional courses IV Optional courses V Seminary Optional courses IV Design and Analysis of Experiments New Production Technologies Code number D 900 D 803 D 802 D 911 4 D D D D D 910 907 908 909 905 25 ANNUAL REPORT 2010 Semester IV Course Product Development Design Standardization and Technical Regulations Optional courses VI Optional courses VII Graduation work Optional courses VI Materials Selection and Application Selected Chapters of Quality Control and Quality Assurance Optional courses VII Transport Systems and Lifts Recycling and Ecological Product Providing Robots and Manipulators L E ECTS S Exam 2 2 2 2 0 8 2 2 2 2 8 16 4 4 4 4 14 30 M M O O M * * * * L E ECTS S Code number 2 2 4 O D 1026 2 2 4 O D 1052 L E ECTS S Code number 2 2 2 2 2 2 4 4 4 O O O D 1009 D 1010 P 606 L E ECTS S Exam 2 2 2 2 2 2 12 2 2 2 2 2 2 12 5 5 5 5 5 5 30 M M M M M O * * * * ** ** 4 Code number D 901 D 1004 D 1020 4 Manufacturing Logistics Semester I Course Designing of Production Systems New Production Strategies and Philosophies Process Planning and Modelling Maintenance Strategies Computer Aided Design Tribology Code number P 604 P 726 D 780 D 1021 D 781 P 752 * Oral or written exam; ** Knowledge verification (program, seminary, colloquy, test) Semester II Course Materials Management Computer Aided Proce ss Planning and Manufacturing Production Management Rapid Prototyping Optional courses I Optional courses II 26 L E ECTS S Exam Code number 2 2 5 M * D 921 2 2 5 M * P 723 2 2 2 2 12 2 2 2 2 12 5 5 5 5 30 M M O O * ** * * 5 D 820 D 1001 ANNUAL REPORT 2010 Optional courses I L E ECTS S Code number Flexible Manufacturing Systems Designing of Technologies Finite Element Method 2 2 2 2 2 2 5 5 5 O O O D 925 D 857 P 705 Optional courses II L E ECTS S Code number 2 2 2 2 5 5 O O D 840 D 842 Tool Materials Composites and Polymers Semester III Course Design and Analysis of Experiments Application of Artificial Intelligence Project Management Information Systems of Production Enterprises Optional courses III Seminary Optional courses III New Production Technologies Quality Management L E ECTS S Exam Code number 2 2 2 2 2 2 5 5 5 M M M ** * * D 923 P 724 D 922 2 2 5 M * D 822 2 0 10 2 4 14 5 5 30 O M * L E ECTS S Code number 2 2 2 2 5 5 O O D 843 D 926 D 911 4 Semester IV Course Optimization of Tribomechanical Systems Materials Selection and Application Computer Integrated Manufacturing Optional courses IV Graduation work Optional courses IV Costs Management Product Data Management Programming L E ECTS S Exam 2 2 2 2 0 8 2 2 2 2 8 16 4 4 4 4 14 30 M M M O M * * * * L E ECTS S Code number 2 2 2 2 2 2 4 4 4 O O O D 824 D 1006 D 1007 Code number D 1022 D 1026 D 1002 D 1020 4 27 ANNUAL REPORT 2010 Materials Engineering Semester I Course Designing of Production Systems Microstructure and Properties of Materials Special Steels Surface Protection Tribology Optional courses I L E ECTS S Exam 2 2 2 2 2 2 12 2 2 2 2 2 2 12 5 5 5 5 5 5 30 M M M M M O * * * * ** ** 4 Code number P 604 D 932 P 751 P 759 P 752 * Oral or written exam; ** Knowledge verification (program, seminary, colloquy, test) Optional courses I Renewable Energy Sources Heat Transfer L E ECTS S Code number 2 2 2 2 5 5 O O D 928 D 728 L E ECTS S Exam Code number 2 2 5 M * D 840 2 2 5 M * D 841 2 2 2 2 12 2 2 2 2 12 5 5 5 5 30 M M M O * ** * * 5 D 842 P 794 D 921 L E ECTS S Code number 2 2 2 2 5 5 O O D 851 D 1010 L E ECTS S Exam 2 2 2 2 2 0 10 2 2 2 2 2 4 14 5 5 5 5 5 5 30 M M M M M O ** * * ** * L E ECTS S Code number 2 2 2 2 5 5 O O D 922 D 1021 Semester II Course Tool Materials Surface Heat Treatment and Surface Engineering Composites and Polymers Temperature Fields Materials Management Optional courses II Optional courses II Welding Recycling and Ecological Product Providing Semester III Course Design and Analysis of Experiments Quality Management Alloys of Non-ferrous Metals Laboratory Materials Testing Optional courses III Seminary Optional courses III Project Management Maintenance Strategies 28 Code number D 923 D 926 D 1033 D 844 D 911 3 ANNUAL REPORT 2010 Semester IV Course Welding Metallurgy Optimization of Tribomechanical Systems Materials Selection and Application Optional courses IV Graduation work Optional courses IV Programming Production Management Code number L E ECTS S Exam 2 2 2 2 0 8 2 2 2 2 8 16 4 4 4 4 14 30 M M M O M * * * * L E ECTS S Code number 2 2 2 2 4 4 O O D 1007 D 820 D 1031 D 1022 D 1026 D 1020 4 Engineering Technologies Semester I Course Casting Engineering Machining Procedures Surface Protection Polymers Processing Designing of Production Systems Optional courses I L E ECTS S Exam 2 2 2 2 2 2 12 2 2 2 2 2 2 12 5 5 5 5 5 5 30 M M M M M O * * * * * ** 5 Code number P 781 P 783 P 759 P 784 P 604 * Oral or written exam; ** Knowledge verification (program, seminary, colloquy, test) Optional courses I Special Casting Procedures Designing of Polymer Products L E ECTS S Code number 2 2 2 2 5 5 O O P 790 D 860 Semester II Course L E ECTS S Exam 2 2 2 2 2 2 12 2 2 2 2 2 2 12 5 5 5 5 5 5 30 M M M M O O * * * * ** ** 4 Optional courses II and III L E ECTS S Code number Foundries Automation Flexible Manufacturing Systems Temperature Fields Technologies of Surface Protection 2 2 2 2 2 2 2 2 5 5 5 5 O O O O D 856 D 925 P 794 D 952 Metal Forming I Designing of Technologies Technological Manufacturing of Products Welding Optional courses II Optional courses III Code number D D D D 782 857 942 851 29 ANNUAL REPORT 2010 Semester III Course New Production Technologies Technological Process Parameters Optimisation Quality Management Optional courses IV Optional courses V Seminary Optional courses IV Maintenance Strategies Project Management Optional courses V Mechanization, Automation and Robotization in Welding Tools and Devices II L E ECTS S Exam Code number 2 2 5 M * D 843 2 2 5 M * D 941 2 2 2 0 10 2 2 2 4 14 5 5 5 5 30 M O O M * * ** D 926 L E ECTS S Code number 2 2 2 2 5 5 O O D 1021 D 922 L E ECTS S Code number 2 2 5 O D 1047 2 2 5 O D 951 L E ECTS S Exam 2 2 2 2 0 8 2 2 2 2 8 16 4 4 4 4 14 30 M M O O M ** * * * L E ECTS S Code number 2 2 2 2 4 4 O O D 1031 D 840 L E ECTS S Code number 2 2 4 O D 1052 2 2 2 2 4 4 O O D 1043 D 1044 D 911 4 Semester IV Course Rapid Prototyping Reliability of Systems Optional courses VI Optional courses VII Graduation work Optional courses VI Welding Metallurgy Tool Materials Optional courses VII Selected Chapters of Quality Control and Quality Assurance Metal Forming II Selected Chapters of Casting Engineering 30 Code number D 1001 D 1042 D 1020 3 ANNUAL REPORT 2010 Courses offered in English Code number D802 D851 D901 D922 D923 D926 D928 D1001 D1023 D1025 P726 P705 P784 D921 Course Fracture Mechanics Welding Product Development Design Project Management Design and Analysis of Experimen ts Quality Management Renewable Energy Sources Rapid Manufacturing New Information Technologies Computer Programs in Mechanical Engineering New Production Strategies and Philosophies Finite Element Method Polymer Processing Materials Management Students of Graduate study programme Engineering Technologies in the ĐĐ Tvornica energetskih postrojenja 31 ANNUAL REPORT 2010 Postgraduate Specialist Study: Development of Products and Technologies Modules ? ? ? ? Application of Manufacturing Processes Production Management Modelling and Numerical Analysis of Constructions Materials Engineering. The duration of the postgraduate specialist study is 3 semesters (with 90 ECTS points). Upon completion of Postgraduate Specialist Study, student is awarded title University Specialist of Mechanical Engineering (univ. spec. mech.). Core common courses semester I Code Head lecturer PS105 Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. PS106 Prof. dr. sc. Ivan Samardžić PS107 Prof. dr. sc. Emil Hnatko PS101 PS102 PS103 PS104 dr. sc. Pero Raos dr. sc. Milan Kljajin dr. sc. Ivica Kladarić dr. sc. Goran Šimunović dr. sc. Roberto Lujić dr. sc. Katica Šimunović dr. sc. Ivica Kladarić dr. sc. Vlatko Marušić dr. sc. Dražan Kozak dr. sc. Todor Ergić dr. sc. Katica Šimunović Course Hours P E ECTS Status Product Development 30 0 10 O Programme Engineering Support 5 25 10 O 15 15 10 I 30 0 10 I 10 20 10 I 25 5 10 I 20 10 10 I ECTS Status Modern Methods of Material Testing Analysis of Bearing Constructions Operational Research Control and Quality Assurance Internal Combustion Engines P – lectures, E - laboratory and experimental work, O – obligatory, I – optional Module: Materials Engineering Module coordinator: Prof. dr. sc. Dragomir Krumes semester II Code PS201 PS202 PS203 PS204 PS205 Head lecturer Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. Prof. dr. dr. dr. dr. dr. dr. dr. dr. dr. dr. dr. dr. sc. sc. sc. sc. sc. sc. sc. sc. sc. sc. sc. sc. Dragomir Krumes Ivica Kladarić Božo Smoljan Vlatko Marušić Dragomir Krumes Ivica Kladarić Vlatko Marušić Dragomir Krumes Ivica Kladarić Ivica Kladarić Dragomir Krumes Vlatko Marušić Course Special Materials and Methods 20 10 10 O Tribology 20 10 10 O 20 10 10 I 20 10 10 I 20 10 10 I 10 I Selected Topics from Materials Surface Engineering and Surface Heat Treatment Modern Technologies of Heat Treatment Selected Courses from other Modules 32 Hours P E ANNUAL REPORT 2010 Module: Modelling and Numerical Analysis of Constructions Module coordinator: Prof. dr. sc. Željko Ivandić semester II Code PS301 PS302 PS303 Head lecturer Prof. Prof. Prof. Prof. Prof. Prof. Prof. Course dr. sc. Franjo Matejiček dr. sc. Dražan Kozak dr. sc. Milan Kljajin dr. sc. Željko Ivandić dr. sc. Dražan Kozak dr. sc. Todor Ergić dr. sc. Franjo Matejiček PS304 Prof. dr. sc. Željko Ivandić Prof. dr. sc. Milan Kljajin PS305 Prof. dr. sc. Dražan Kozak Prof. dr. sc. Franjo Matejiček Numerical Analysis of Mechanical Systems Modelling of Constructions and Design Process Hours P E ECTS Status 20 10 10 O 20 10 10 O Fatigue Strength 20 10 10 I Selected Topics from Mechanical Engineering Elements 20 10 10 I Service Life of Constructions 20 10 10 I 10 I Selected Courses from other Modules Module: Application of Manufacturing Processes Module coordinator: Prof. dr. sc. Ivan Samardžić semester II Code PS401 PS402 Head lecturer Prof. Prof. Prof. Prof. Prof. Prof. dr. dr. dr. dr. dr. dr. sc. Ivan Samardžić sc. Pero Raos sc. Stjepan Aračić sc. Ivan Budić sc. Branko Grizelj sc. Antun Stoić PS403 Prof. dr. sc. Branko Grizelj PS404 Prof. dr. sc. Ivan Budić PS405 Prof. dr. sc. Stjepan Aračić PS406 Prof. dr. sc. Pero Raos Prof. dr. sc. Ivan Samardžić PS407 Prof. dr. sc. Antun Stoić Course Hours P E ECTS Status Modern Manufacturing Procedures I 20 10 10 O Modern Manufacturing Procedures II 20 10 10 O New Processes and Methods in Metal Forming Special Casting Procedures Corrosion Damages of Structural Steel 25 5 10 I 30 0 10 I 30 0 10 I Modern Joining Processes 20 10 10 I 30 0 10 I 10 I High Efficiency Processes of Metal Cutting Selected Courses from other Modules 33 ANNUAL REPORT 2010 Module: Production Management Module coordinator: Prof. dr. sc. Katica Šimunović semester II Code PS501 PS502 PS503 PS504 PS505 PS506 Head lecturer Course Prof. dr. sc. Goran Šimunović Prof. dr. sc. Tomislav Šarić Prof. dr. sc. Katica Šimunović Prof. dr. sc. Roberto Lujić Prof. dr. sc. Tomislav Šarić Doc. dr. sc. Tomislav Galeta Prof. dr. sc. Maja Lamza-Maronić Prof. dr. sc. Roberto Lujić Prof. dr. sc. Goran Šimunović Prof. dr. sc. Goran Šimunović Prof. dr. sc. Tomislav Šarić Prof. dr. sc. Roberto Lujić Prof. dr. sc. Tomislav Šarić Doc. dr. sc. Tomislav Galeta Hours P E ECTS Status Information System of Production Enterprises 5 25 10 O Managerial Methods and Strategies 15 15 10 O Production Management 5 25 10 I Preparation and Production Management 5 25 10 I Information Technologies in Production 5 25 10 I 5 25 10 I 10 I ECTS Status 30 O Computer Support in Product Preparation Selected Courses from other Modules semester III (for all modules) Code PS601 Head lecturer Course Potential supervisors Final Specialist Work Courses offered in English Code PS PS PS PS PS PS PS PS PS PS 34 101 104 106 301 303 305 407 502 504 506 Course Product Development Analysis of Bearing Constructions Control and Quality Assurance Numerical Analysis of Mechanical Systems Fatigue Strength Service Life of Constructions High Efficiency Processes of Metal Cutting Managerial Methods and Strategies Preparation and Production Management Computer Support in Product Preparation Hours P E 0 0 ANNUAL REPORT 2010 Postgraduate Doctoral Study: Mechanical Engineering The postgraduate doctoral study at the Mechanical Engineering Faculty in Slavonski Brod of Josip Juraj Strossmayer University of Osijek is organised as a full-time study pursuant to the regulations of the Act on Scientific Activity and Higher Education (Narodne novine 123/03) for candidates holding a master's degree or a graduate degree and at least 300 ECTS points. The current postgraduate students could also transfer to this postgraduate doctoral study. The aim of this postgraduate doctoral study is to enable successful candidates to earn the academic title doctor of science (dr. sc.) in the area of Technical sciences, in the field of Mechanical Engineering and provide them with the knowledge and skills necessary for individual scientific research work. The education of teaching staff ensures the scientific potential for the forthcoming generations and the continuity of the scientific and research work in the field of mechanical engineering in the region of Slavonija and Baranja. The scientists and researchers holding the degree should be able to carry out research projects and tasks by applying the most recent scientific methods and models and by performing experiments and tests in the field of mechanical engineering (new manufacturing technologies, new strategies in manufacturing logistics and new materials). Admission to the postgraduate doctoral study is announced by the Academic Senate of Mechanical Engineering Faculty. The following candidates are admitted to the doctoral study: ? ? ? ? graduate mechanical engineers, candidates with a Master's degree, those who completed their master's programme but did not defend their thesis and candidates who won their degree in compliance with the Scientific Activity and Higher Education Act (Narodne novine 123/03). Postgraduate study admission requirements for graduate mechanical engineers are: ? ? average grade ≥ 3,8, belonging to a group of 10 % best students in the generation or a recommendation of two full professors, competence in one of the world languages, checked before enrolment. The candidates who graduated according to the "old programme" get 300 ECTS points and they have to enrol the 1st semester of the doctoral study. 35 ANNUAL REPORT 2010 Description of Programme All students are obliged to take core courses and thematic courses of the doctoral study specialised field in due time. Core courses The core courses are primarily meant to give students basic methodological and fundamental knowledge. The students are acquainted with different methodologies, philosophy of science, specific basic knowledge, particularly such that is necessary in engineering, i.e. mechanical engineering. The courses are offered in the form of compulsory lectures, experimental work and seminars. Thematic courses The purpose of the thematic courses in modules is to ensure specialisation. The emphasis is placed first of all on the theoretical and practical level of education, understanding of theoretical approaches and the most recent research results in a specific field of study. The selected option (module) enables the students to specialise in several directions and helps them in their research through various forms of work suitable for the specified topic (individual, seminars and short reports on the research, experimental work, etc.). These courses are meant to provide students with detailed knowledge of a specific field, helping them to carry on independent research and achieve original results. The postgraduate degree programme includes three modules: ? ? ? Modern Manufacturing Processes Modern Production Management Design and Numerical Modelling of Products. Module: Modern Manufacturing Processes The main purpose of the module is to provide students with knowledge and skills needed for independent scientific-research and professional work in the field of development and application of new engineering technologies. Engineering technologies cover a broad area of conventional technologies: casting, deforming, chip-forming machining, welding, heat treatment, anticorrosive protection, and of new technologies: surface engineering, laser technologies, application of high-speed machining and machines, highly automated flexible manufacturing systems. By experimental research into new areas of technology application and by mathematical modelling and simulation of 36 ANNUAL REPORT 2010 machining operations, the students are trained for a systematic approach in solving technological problems. Module: Modern Production Management This programme is designed to prepare students for independent research and professional work in the management of production, materials, quality assurance, production planning and maintenance. By getting acquainted with new strategies, processes and methods in manufacturing logistics, computer aided production planning and management, as well as with optimisation methods in manufacturing processes, the students are trained for research work in rationalisation of management and functioning of production systems. Module: Design and Numerical Modelling of Products The main purpose of this module is scientific upgrading of candidates and their training for independent scientific-research work and for application of new methods and ideas to design, analysis and synthesis of machine structures. The term design of machine structures implies the process which as a rule consists of idea, concept, project, construction and design of a structure. This module broadens and deepens the knowledge connected with systematic creation and development of structures, design theory, application of numerical methods in mechanics, methods of theoretical and experimental analysis of structures, application of new methods to structural analysis of constructions in view of optimal design of structures. The list of compulsory and elective courses by modules The postgraduate degree programme contains the following groups of compulsory and elective courses: ? ? ? core common courses (TK) module courses (KM) module seminar courses (SM). All courses of the doctoral study are foreseen in duration of one semester with the same number of ECTS points that amounts to 7,5. Total number of compulsory and elective courses is 8, so that the total number of ECTS points, which the student could achieve by passing all exams, is 60. 37 ANNUAL REPORT 2010 st In the 1 semester, the student chooses three core common courses, which serve for acquirement of fundamental and methodological knowledge necessary for the study continuation. Two out of three courses are obligatory for all candidates (PD101 and PD102), while the third course should be chosen as one of three offered courses (PD103, PD104 or PD 105) in agreement with the leader of the module of the doctoral study. The module courses serve for the knowledge profilation of the doctoral study candidate. All module courses are foreseen as elective, but the student has to select 2 module courses from the nd rd list in the 2 and 3 semester, and 1 module seminar course from th the list in the 4 semester. This selection should be supervised by the leader of the module and mentor of the PhD thesis. Semesters 5 and 6 are foreseen for the research related to the topic of the doctoral dissertation. The schedule of courses of the doctoral study arranged by semesters with assigned ECTS points is presented in the Table 1. It is specified that the students collect 1/3 of total of 180 ECTS points by fulfilling the obligations from the educational process, while remaining 2/3 of ECTS points have to be achieved on the basis of performed researches. Table 1: Courses of the postgraduate doctoral study by semesters Courses Semester Core common courses (TK) Module courses (KM) Module seminar courses (SM) Work from the field of investigation Doctoral dissertation 1st 3 2nd 3rd 2 2 4th Number of courses 5th 6th 1 constantly through the study 3 4 1 Sum o f ECTS points: 38 ECTS points 22,50 30,00 7,50 90,00 30,00 180,00 ANNUAL REPORT 2010 Core common courses semester I Code Head lecturer Prof. dr. sc. Dražan Kozak PD101 Prof. dr. sc. Marija Živić Prof. dr. sc. Katica Šimunović Prof. dr. sc. Rudolf Scitovski PD102 Prof. dr. sc. Mirta Benšić Doc. dr. sc. Kristian Sabo Prof. dr. sc. Ivan Budić PD103 Prof. dr. sc. Pero Raos Prof. dr. sc. Ivan Samardžić Prof. dr. sc. Goran Šimunović PD104 Prof. dr. sc. Tomislav Šarić Prof. dr. sc. Roberto Lujić Prof. dr. sc. Franjo Matejiček PD105 Prof. dr. sc. Luka Sopta Prof. dr. sc. Marija Živić Course Hours P E ECTS Logistics of Scientific Research Work 30 0 7,5 Mathematics and Statistics 30 0 7,5 Modern Manufacturing Processes 20 10 7,5 Applying of the Artificial Intelligence 20 10 7,5 Numerical Methods in Mechanics 30 0 7,5 Faculty/ Departm. SF SF SF MO MO MO SF SF SF SF SF SF SF TFR SF Abbreviations BZ – Bay Zoltań Institute for Logistics and Production Systems Miskolc E – laboratory and experimental work EF – Faculty of Economics - Osijek ETF – Faculty of Electrical Engineering - Osijek FESB – Faculty of Electrical Engineering, Mechanical Engineering and NavalArchitecture - Split FSLJ – Faculty of Mechanical Engineering - Ljubljana FSM – Faculty of Mechanical Engineering - Maribor I – optional MO – Department of Mathematics - Osijek O – obligatory OS – Osijek P – lectures PF – Faculty ofAgronomy - Osijek PMF – Faculty of Natural Sciences and Mathematics – Zagreb SF – Faculty of Mechanical Engineering - Slavonski Brod TFR – Faculty of Engineering - Rijeka 39 ANNUAL REPORT 2010 Module: Modern Manufacturing processes Module coordinator: Prof. dr. sc. Pero Raos semester II Code Head lecturer Course Hours P E ECTS Prof. dr. sc. Pero Raos Prof. dr. sc. Ivan Samardžić PD202 Prof. dr. sc. Ivan Budić High Efficiency Joining Processes Modern Casting Technologies 20 10 7,5 20 10 7,5 PD203 Prof. dr. sc. Branko Grizelj Prof. dr. sc. Pero Raos PD204 Prof. dr. sc. Milan Kljajin Doc. dr. sc. Tomislav Galeta Deformation Manufacturing 20 10 7,5 Rapid Prototyping and Manufacturing 20 10 7,5 30 0 7,5 30 0 7,5 PD201 Selected courses from other modules Selected courses from other faculties (University of OS) Faculty/ Departm. SF SF SF SF SF SF SF semester III Code Head lecturer Prof. PD301 Prof. Prof. Prof. PD302 Prof. Prof. Prof. Prof. PD303 Prof. Prof. Prof. PD304 dr. sc. Ivica Kladarić dr. sc. Ivan Budić dr. sc. Vlatko Marušić dr. sc. Janez Kopač dr. sc. Antun Stoić dr. sc. Branko Grizelj dr. sc. Pero Raos dr. sc. Ivan Budić dr. sc. Milan Kljajin dr. sc. Ivan Samardžić dr. sc. Stjepan Aračić Prof. dr. sc. Dragomir Krumes Prof. dr. sc. Ivica Kladarić Course Hours P E ECTS Thermal Activated Processes 20 10 7,5 High Speed Machining Processes and Systems 20 10 7,5 Technology of the Product 20 10 7,5 20 10 7,5 30 0 7,5 30 0 7,5 Modifying Surface of Materials and Surface Engineering Selected courses from other modules Selected courses from other faculties (University of OS) Faculty/ Departm. SF SF SF FSLJ SF SF SF SF SF SF SF SF SF semester IV Code Head lecturer Prof. dr. sc. Ivan Samardžić PD401 Prof. dr. sc. Nedjeljko Mišina Prof. dr. sc. Vladimir Gliha PD402 Prof. dr. sc. Stjepan Aračić PD403 40 Prof. dr. sc. Vlatko Marušić Prof. dr. sc. Dragomir Krumes Course Welding – Selected Chapters Mechanism and Prevention of Corrosion Damages Selected Chapters from Materials Selected courses from other modules Selected courses from other faculties (University of OS) Hours P E ECTS Faculty/ Departm. 20 10 7,5 SF FESB FSM 20 10 7,5 SF 20 10 7,5 SF SF 30 0 7,5 30 0 7,5 ANNUAL REPORT 2010 Module: Modern Production Management Module coordinator: Prof. dr. sc. Goran Šimunović semester II Code Head lecturer Prof. Prof. Prof. PD502 Prof. Prof. PD501 dr. sc. Dražen Barković dr. sc. Katica Šimunović dr. sc. Ivica Veža dr. sc. Roberto Lujić dr. sc. Katica Šimunović Prof. dr. sc. Goran Šimunović PD503 Prof. dr. sc.Tomislav Šarić Doc. dr. sc. Tomislav Galeta PD504 Prof. dr. sc. Rudolf Emert Prof. dr. sc. Tomislav Šarić Course Hours P E ECTS Faculty/ Departm. EF SF SF FESB SF Operational Management 20 10 7,5 Production, Project and Resource Management 20 10 7,5 Computer Aided Design, Process Planning and Manufacturing (CAD/CAPP/CAM) 20 10 7,5 SF SF SF New Maintenance Strategies 20 10 7,5 PF SF 30 0 7,5 30 0 7,5 Selected courses from other modules Selected courses from other faculties (University of OS) semester III Code PD601 PD602 PD603 PD604 Head lecturer Prof. dr. sc. Goran Šimunović Prof. dr. sc. Roberto Lujić Prof. dr. sc. Katica Šimunović Prof. dr. sc. Tom islav Šarić Prof. dr. sc. Goran Šimunović Prof. dr. sc. Jože Balič Prof. dr. sc. Roberto Lujić Doc. dr. sc. Tomislav Galeta Prof. dr. sc. Maja Lamza-Maronić Course ERP Systems Intelligent Production Systems Information Systems: Strategy & Management Human Resource Management Selected courses from other modules Selected courses from other faculties (University of OS) Hours P E ECTS 20 10 7,5 20 10 7,5 20 10 7,5 30 0 7,5 30 0 7,5 30 0 7,5 Faculty/ Departm. SF SF SF SF FSM SF SF SF SF semester IV Code Head lecturer Prof. dr. sc. Tomislav Šarić Prof. dr. sc. Marinko Stojkov Prof. dr. sc. Tomislav Šarić PD702 Prof. dr. sc. Antun Stoić Doc. dr. sc. Tomislav Galeta PD703 Prof. dr. sc. Ivan Samardžić Prof. dr. sc. Roberto Lujić PD704 Prof. dr. sc. Maja Lamza-Maronić PD701 Course Hours P E ECTS Faculty/ Departm. Diagnostics 18 12 7,5 Flexible Manufacturing Systems 18 12 7,5 Quality Management 18 12 7,5 SF SF SF SF SF SF Strategic Management 18 12 7,5 SF 30 0 7,5 30 0 7,5 Selected courses from other modules Selected courses from other faculties (University of OS) 41 ANNUAL REPORT 2010 Module: Design and Numerical Modelling of Products Module coordinator: Prof. dr. sc. Milan Kljajin semester II Code Head lecturer Course Hours P E ECTS Faculty/ Departm. Prof. dr. s c. Milan Kljajin PD801 Prof. dr. sc. Jože Duhovnik Prof. dr. sc. Željko Ivandić Design Theory 30 0 7,5 SF FSLJ SF PD802 Prof.dr.sc. Franjo Matejiček Elastomechanics and Plastomechanics 30 0 7,5 SF Thin-Walled Structures 30 0 7,5 Theory of Mechanical Engineering Systems 30 0 7,5 30 0 7,5 30 0 7,5 Prof. PD803 Prof. Prof. Prof. PD804 Prof. Prof. dr. sc. Dražan Kozak dr. sc. Franjo Matejiček dr. sc. Todor Ergić dr. sc. Milan Kljajin dr. sc. Jože Duhovnik dr. sc. Željko Ivandić Selected courses from other modules Selected courses from other faculties (University of OS) SF SF SF SF FSLJ SF semester III Code Prof. Prof. Prof. PD902 Prof. Prof. Prof. PD903 Prof. Prof. Prof. PD904 Prof. Prof. PD901 Head lecturer dr. dr. dr. dr. dr. dr. dr. dr. dr. dr. dr. sc. Franjo Matejiček sc. Dražan Kozak sc. Milan Kljajin sc. Nenad Gubeljak sc. Željko Ivandić sc. Franjo Matejiček sc. Nenad Gubeljak sc. Dražan Kozak sc. Milan Kljajin sc. Božidar Križan sc. Željko Ivandić Course Hours P E ECTS Finite Element Method in Structural Analysis 26 4 7,5 Modelling of Design and Design Processes 26 4 7,5 Fatigue Strength and Fracture Mechanics 26 4 7,5 30 0 7,5 30 0 7,5 30 0 7,5 Selected Topics from Mechanical Engineering Elements Selected courses from other modules Selected courses from other faculties (University of OS) Faculty/ Departm. SF SF SF FSM SF SF FSM SF SF SF TFR semester IV Code Head lecturer Prof. dr. sc. Milan Kljajin PD951 Doc. dr. sc. Lavoslav Čaklović Prof. dr. sc. Željko Iv andić Prof. dr. sc. Dražan Kozak PD952 Prof. dr. sc. Franjo Matejiček Prof. dr. sc. Emil Hnatko Prof. dr. sc. Milan Kljajin PD953 Prof. dr. sc. Jože Duhovnik Prof. dr.sc. Todor Ergić Prof. dr. sc. Ivan Samardžić Prof. dr. sc. Dražan Kozak PD954 Prof. dr. sc. Željko Domazet Prof. dr. sc. László Tóth Course Methodology for the Evaluation of Design Alternatives Calculation, Design and Optimization of Mechanical Construction ECTS 30 0 7,5 30 0 7,5 Product Development and Ergonomics 24 6 7,5 Damages of Constructions 20 10 7,5 30 0 7,5 30 0 7,5 Selected courses from other modules Selected courses from other faculties (University of OS) 42 Hours P E Faculty/ Departm. SF PMF SF SF SF SF SF FSLJ SF SF FESB BZ ANNUAL REPORT 2010 Obligatory and optional activities (taking part in seminars, conferences, round-table talks etc.) and criteria to express them in ECTS points All postgraduate students must attend lectures at the Faculty whether they come from some higher education institution or from some scientific institution. Besides taking core courses and thematic courses of the specialised field (module) or compulsory and elective courses of the basic module and elective courses from other modules and other faculties, the doctoral study also requires of all students to engage in some of the following compulsory or optional activities that are associated with the original scientific research like for example: Compulsory activities: ? ? ? ? ? Attending lectures Taking part in seminars and preliminary exams (within a course/module, etc.) Taking part in thematic round-table talks and workshops It is obligatory for all students to spend some time abroad Publishing in magazines. It is important to point out that all postgraduate students must spend some time in an adequate research centre abroad. The proposer of the study must provide the necessary data on scholarships and give the candidates the adequate support so that they can apply for these scholarships. Optional activities: ? ? ? ? Taking part in conferences (actively) Presenting results of current researches at the Scientific Forum (at the Faculty) Participating in scientific-research projects Work on technological projects and projects for the economy. The listed activities bring the postgraduate doctoral study student additional 90 ECTS points according to the criteria given on the next page. 43 ANNUAL REPORT 2010 ECTS 2,5 Taking part in seminars 2,5 Taking part in round -table talks 2,5 Taking part in workshops 5 44 Activity Presenting results of the researches at the Scientific Forum (at the Faculty) 7,5 Publishing in journals 15 Publishing in journals as the only author 7,5 Taking p art in conferences 7,5 Participating in scientific-research projects 15 Participating in international scientific research projects 7,5 Participating in scientific-research projects 15 Study stays abroad Criteria and explanation The student participates actively in seminars within the framework of the course or the module. The seminars are thematic and the theme is either proposed by the student or initiated by the leader of the module or by the lecturers. The theme does not have to be an integral part of the dissertation. The seminars result in written papers, marked at the end of the seminar. If the seminars are organised at another faculty, the student must provide a certificate of regular attendance and active participation in the seminar. Similar to seminars, the students participate in roundtable talks which are thematically connected with the taken module. The round-table leader’s report on active participation is sufficient for earning credit points. Workshops provide a number of opportunities for students to discuss results of work assignments introduced in lectures of one or more modules. Taking part in other faculty workshops is also acknowledged if the topics discussed are related to the field of the student’s study programme or dissertation. Scientific Forum was founded at Mechanical Engineering Faculty so that junior researchers, assistants and postgraduate students could present their research results and share their ideas. During the postgraduate study, the students must publish in journals (preferably in journals with internationally accepted reviews or of the same quality as journals from Croatia, or referred in well-known data bases, etc.) either on their own or assisted by the mentor, leader of the module, course lecturer, or as a co-author. If the student is the only author of a paper and the paper deals with the dissertation topic (preliminary notes or original scientific paper), the student is entitled to a doubled number of points. If the student participates in a scientific conference (in Croatia, in Croatia with international participation, or international) and presents a paper as the author or co-author, with a document proving this participation and the paper published in the conference proceedings, the student is entitled to additional ECTS points. For an active participation as researcher in a scientificresearch project which will also serve as a basis for the realisation of the dissertation. For an active participation in international scientific projects or independent coordination of a smaller scientific project (within a bigger project). For an active participation in scientific-research projects for the industry, related to the dissertation topic. If experimental or other scientific researches (related to the dissertation) require that the student stays abroad for 3 months or more, and the student receives the EU financial support for it (such as TEMPUS, Fulbright, Humboldt, DAAD scholarship, etc.), which can be documented, the student is entitled to additional ECTS points. ANNUAL REPORT 2010 Courses offered in English Code PD PD PD PD PD PD 101 103 104 204 302 401 PD 503 PD PD PD PD PD PD 603 703 801 803 901 903 PD 952 Course Logistics of Scientific Research Work Modern Manufacturing Processes Applying of the Artificial Intelligence Rapid Prototyping and Manufactur ing High Speed Machining Processes and Systems Welding – Selected Chapters Computer Aided Design, Process Planning and Manufacturing Information Systems: Strategy & Management Quality Management Design Theory Thin-Walled Structures Finite Element Method in Structural Analysis Fatigue Strength and Fracture Mechanics Calculation, Design and Optimization of Mechanical Construction The Mechanical Engineering Faculty at the location in Ivan Gundulić 20A 45 ANNUAL REPORT 2010 Scientific and Research Projects Increase of the Efficiency of Casting Procedures - Croatian Perspectives Project results in year 2010: In the year 2010, the research was focused on the influence of technological parameters on residual stresses in die castings. The influence of following technological parameters was investigated: ? temperature of pouring, °C ? filling of mould with molten metal, m/s ? pressure increase in the filled mould, bar ? cooling time of castings with pouring system, after breaking the casting out of the mould, min. The research results are used for improving the casting processes. As a result of this investigation, a PhD thesis was successfully finished by a young researcher on this project, Daniel Novoselović. PhD thesis was defended on 16 July 2010. The results of these investigations have been published in journals and conference proceedings. The textbook entitled: "Osnove tehnologije kalupljenja - Jednokratni kalupi I. dio, II. izmijenjeno i dopunjeno izdanje" has also been published. Continuous detailed analysis of castings is being done in some foundries: Lipovica d. o. o. - Popovača, Plamen International Požega and Faculty of Mechanical Engineering and Naval Architecture - Zagreb, as well. a) checkout of cables resistance b) device for drilling c) perpendicularity adjustment d) centrality adjustment Connection checkout and installation of equipment for drilling 46 Project coordinator: Professor Ivan Budić E-mail: [email protected] Phone: +385 35 446 188 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2007-2011 Programme type: National project ANNUAL REPORT 2010 CAD/CAM Method of Modern Tool Construction for High Strength Steel Plates in 4D Project results in year 2010: During the year 2010, the effects of process parameters on mechanical properties of bent sheet metal plates have been investigated (especially the effects of process parameters on the amount of elastic sheet metal spring-back). FEM method was used for numerical simulations. Elastic spring-back is very important for every process where sheet metal is processed in order to maintain desired dimensions and tolerances after the forming process. Since there is a trend of using high strength/low mass ratio of new materials, mostly high strength steel metal plates are used in the forming processes all over the world. Project coordinator: Professor Branko Grizelj E-mail: [email protected] Phone +385 35 493 426 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2007-2011 Programme type: National project Data for investigated processes were collected and some conclusions were made regarding the behavior of high strength sheet metal plates. Also the tool for the experimental investigation was designed and modeled for future research. The goal is to investigate behavior of high strength steel sheet metal plates in various sheet forming processes, with various forming parameters. During the last year, the hydroforming processes were also investigated by FEM method. Hydroforming is a process of forming where fluid transfers pressure on every part of the metal surface thus forming it. It can be done as forming of the tubes or the forming of the sheet metal plates onto the die surface. With die and hydroforming of high strength steel sheet metal plates, most of the car parts are made: hood, fenders, and various curved metal parts which need to ensure high rigidity and low mass of product. 47 ANNUAL REPORT 2010 Research of the IC Engine Combustion Control and Management Project results in year 2010: In the year 2010, investigation was focused on the thermodynamic process inside the cylinder of internal combustion engine. The most sensitive part of this process is the combustion process inside the cylinder. It is necessary to optimize the IC engine combustion process to ensure optimal parameters during the conversion of heat energy into mechanical work inside the engine. Using simulations, the possibility of controlling the optimization processes by using the required amount of fuel in the process of injecting the fuel into the cylinder was investigated. Three models were tested: prof. Woschni Model, Lotus Model and prof. Medica Model. The Woschni Model, based on the classical Wiebe function (which is used to predict the burn fraction and burn rate in internal combustion engines), shows relatively few variable parameters and requires complex computer support. Therefore, it is extremely complicating to improve this model. The Lotus Model is a commercial model with excellent characteristics and possibilities, but a special licence is needed for its use. The price is extremely high and therefore not within our modest budget. The model of Prof. Medica (who is also a researcher on this project) can encompass all the needs of the project concerning the applied research and optimization of combustion process. It requires special training, as well as very demanding computer memory. This will be the basis for research in the next period. 48 Project coordinator: Professor Emil Hnatko E-mail: [email protected] Phone: +385 35 493 411 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2007-2011 Programme type: National project ANNUAL REPORT 2010 Products Properties for a Global Product Realization by Rapid Production Project results in year 2010: During the year 2010, input lists generation model for new products was finished and tested. The input lists generation model (Figure 1) is a general model, faced with all necessary know-how to ensure the development of MFF (Matrix of Function and Functionality). The input list is a list where all input data that are to be used for calculations and bindings between functions and functionalities are defined and specified. Since in this case we are dealing with bindings between functions and functionalities within MFF, two input lists should be defined – the functions list and the functionalities list. Input lists of functions reflect market needs, representing simultaneously input functional requirements, ideas and engineering goals. These requirements are the first information on a possible new product. As a rule, functional requirements are unarranged and sporadically represented. However, in the sense of the input list, they are arranged and in the form of an orderly system they provide an important link and binding between them. Figure 1. Model of input lists Project coordinator: Professor Milan Kljajin E-mail: [email protected] Phone: +385 35 493 415 In accordance with the MFF model, all defined functional requirements are specified by means of "Names Suggestor", which takes care of credibility and correctness of a new entry. Input lists of functionality describe functions holders of a particular functionality. They materialize through the execution by means of particular processing, manufacturing, working, assembly, transport and application technologies. The functionality list can be specified according to a personal opinion or decisions or the relevant choice is left to the automated suggestion by the software package for the generation of input lists. Following the algorithm, it examines matches with existing solutions in the database and suggests a solution – functionality – on the basis of percentage match. Well-described data in the database are the basis for quality definitions of functionalities. During the description and descriptions generation, the "Names Suggestor" takes care of it. In the MFF model, technical systems are generally marked with TS1, TS2, TSj (j.=.1,…,.n), while in real examples and implementations they are of course replaced by real names of technical systems. Columns with the names of technical systems, described in the matrix are placed under the first line. For each new entry of a technical system, a new column appears in the matrix. The same analogy applies also to the expected input functions that are to be solved. Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2007-2011 Programme type: National project 49 ANNUAL REPORT 2010 Analysis and Fracture Assessment of Structures of Anisotropic Materials F One stage of project investigation related to structural integrity assessment of heterogeneous structures was successfully completed. Previously known investigations included only structural assessment of homogeneous structures or structures with one level of material mismatch, and existing structural integrity assessment methods were limited in their applications to such structures, making it impossible to assess heterogeneous structures with two levels of material mismatch (e.g. welded constructions subjected to repair welding). Since most of structural assessment methods are based on compendia of yield load solution, a compendium of yield load solutions is generated for I butt welded repaired welded joint in context of three point bend specimen (Figure 1). Such work included systematic investigation of influence of geometry parameters and mechanical properties of present materials in weld, primarily using finite element method and statistical methods to derive mathematical expressions needed for compendia generations. Failure criterion for yield load solution was load value causing yield zone to spread across the whole net-section of investigated specimen (Figure 2). This compendium was implemented in SINTAP procedure (Structural INTegrity Assessment Procedure), with some adaptations in order to generate a module for assessment of heterogeneous structures. With existing modules, only highly conservative assessment of heterogeneous construction could be performed, with approximation considering heterogeneous weld as one level of mismatch welded joint. Now, with this compendium more precise assessment of heterogeneous structure can be performed. Furthermore, this extensive investigation gives insight in complex interaction between geometrical parameters and mechanical properties of weld materials with fracture resistance of heterogeneous welded joint. As a result of this investigation, a PhD thesis "Analysis of weld geometry and mechanical properties of weld materials on fracture behaviour of repaired welded joint" was successfully finished by Pejo Konjatić, a young researcher on this project. As part of continuous training, assistant Josip Sertić spent 30 days at Faculty of Mechanical Engineering in Belgrade, Serbia, where he successfully acquired new knowledge needed for further investigation on this project. BM a W/2 S=4W Figure 1. Three point bend specimen Figure 2. Yield zones shapes for different weld root widths by the constant value of a/W=0,5 Figure 3. Determination of critical load using SINTAP procedure (option 2B – FAD approach) Project coordinator: Professor Dražan Kozak E-mail: [email protected] Phone: +385 35 493 400 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2007-2011 Program type: National project 50 W/2 2H B WM1 As a result of investigation on this project (financed by Croatian Ministry of Science, Education and Sports), a significant number of scientific and professional papers were published in the year 2010. Therefore, it is the project with most publications in the scientific area of mechanical engineering with 43 publications in journals and 38 publications at international conferences. WM2 Project results in year 2010: ANNUAL REPORT 2010 Influence of Duplex Process on Steel Structure and Surface Engineering Project results in year 2010: Structural changes in alloys induce changes of specific volume of the newly built grid. In steels the most intensive grid volume changes occur at phase transformation level, i.e. it is necessary that the tempered product changes its volume in relation to still unheated part of the product, especially in thermodifussional heat treatment. Thermodiffusion creates in surface layers of steels or castings thin surface layer of carbides B, V, Ti, N or Nb, which generate very hard and stabile connections, These surface with very hard carbide layers have great resistance to tribological wear, which in the endresult prolongs the life time of products and tools. This project has envisaged the following research: ? ? ? ? ? The influence of thermodiffusion process on product components, design and tool volume changes; Establishment of phase transformation (A1 and A3) and martensite transformable size changes (temperature Ms); One of the research goals is establishment of temperature height Ms in steels with increased hardness values treated with thermodiffusion process (continuation of many year research on thermodiffusion process in steels); Extremely hard duplex layers on steel surface layers, such as: Fe2B, VC, VB, VN, TiC, TiN, CrN, VN, BN and others; The influence of duplex process on tribological properties (adhesion, abrasion, erosion, tribocorrosion) of construction steels with increased hardness values. In 2010 Andrijana Milinović received PhD degree at Mechanical Engineering Faculty in Slavonski Brod. The title of doctoral thesis was "Research of boride layers formation kinetics on carbon steels". Project coordinator: Professor Dragomir Krumes E-mail: [email protected] Phone: +385 35 493 447 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2007-2011 Programme type: National project 51 ANNUAL REPORT 2010 Advanced Technologies of Direct Manufacturing of Polymeric Products Project results in year 2010: The research in 2010 was focused on the following areas: rapid prototyping (RP), non-traditional and ecologically acceptable treatment procedures, as well as the traditional treatment procedures. Part of the rapid prototyping research is the analysis and systematisation of RP procedures and rapid tooling (RT) based on the shape of the base material, the mechanism of forming and the type of procedure. The main characteristics, advantages and disadvantages of certain procedures are analysed. The use of RP and RT in engineering and medicine are investigated in detail. A number of products was designed and technologically produced by using the computer for rapid prototyping by 3D printing, and the hybrid procedure (OBJET) and the STL files were prepared. Design characteristics of all the selected products were analysed in detail (based on the type of procedure). The influence of moulds made by rapid prototyping, i.e. material, on the characteristics of the final product (cast) is investigated. Therefore, the prototype moulds were made by chip-forming and rapid prototyping. By adapting the existing software (Moldex and CadMould), the possibilities of computer simulation of injection pressing were tested on the moulds made by RP. The possibilities of RP of individual medical implants (custom made implants) are being extensively investigated. Medical CTs and MRIs are processed by using the computer software 3D Doctor in order to make CAD medical models as the basis for making RP implants. Based on these models, the characteristics of making implants by using 3DP and OBJET were tested. Virtual medical models Project coordinator: Professor Pero Raos E-mail: [email protected] Phone: +385 35 493 414 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Programme No. 152-1521473 (Programme coordinator Professor Pero Raos) Project No. 152-1521473-1474 Project duration: 2007-2011 Physical (RP) medical model 52 Programme type: National project ANNUAL REPORT 2010 Advanced Joining Technology in Light Mechanical Constructions Project results in year 2010: The area of research in 2010 was the following: During the investigation of cost effective joining processes of thin materials, the emphasis was put on cost efficiency as an important criterion in joining technology selection. The practical examples of modern welding processes application in production processes like LaserHybrid welding, MAG-STT welding, CMT process, FastRoot process and plasma welding are analysed. Also, the application and further developing of On-line monitoring system for main welding parameters acquisition and data processing at different fusion and pressure welding processes was investigated. Practically developed On-line monitoring system was applied, as well as other laboratory methods for the same measurements as a confirmation and validation of data recorded by On-line monitoring system for different welding processes. Based on obtained results, it is possible to conclude that presented monitoring system is suitable for practical application. This monitoring system was applied in order to evaluate the influence of different welding process parameters variations on the stability of the welding process. The weldability and the influence of welding parameters and welding conditions on the properties of the weld joint are investigated through weld thermal cycle simulation, investigation of mechanical properties and by macro and micro analysis of the weld zone. Monitoring of voltage and current (Resistance spot welding) Project coordinator: Professor Ivan Samardžić E-mail: [email protected] Phone: +385 35 446 789 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2007-2011 Programme type: National project 53 ANNUAL REPORT 2010 Advanced Cutting Techniques for Environmentally Friendly Manufacturing Project results in year 2010: The test samples for turning tests were made of heat treated steel. Two different structures with significant difference in hardness were obtained on test samples which enables monitoring and comparison of conditions of cutting hard and soft materials. These tests were conducted at different cutting regimes (cutting speed, feed rate and cutting depth). Digitalized images of microstructure of chips and the analysis of particle shape in the analyzed surface were performed. Microstructure measurements are determined by the baseline thickness of elementary lamellae, on the basis of these data and the frequency of creating fins. Laboratory measurements of components of cutting force and acceleration in the processing of test samples were recorded. Microhardness measurements were conducted on machined surfaces, as well as on rough surfaces. Mathematical models were created to determine the frequency of changes of stress on the results of microanalysis of single particles and the geometric size of test samples. The machinability (according to the wear of tools) of Inconel 718 was investigated (e.g. dry machining, MQL, liquid nitrogen, gaseous nitrogen, classically cool). The results of comparative cryogenic treatment (liquid nitrogen) as compared to conventional processes were experimentally verified by analyzing: cutting force, tool wear, temperature and cost. Cryogenic technology has high potential for cost reduction, creating less waste, and it also has lower environmental and social impact. Studies have been done by measuring the quality of the cooling flush and lubrication. In collaboration with the Head of the LABOD from Ljubljana, Prof. Janez Kopač who was a subcontractor on the project, a research on the utilization of alternative coolants and lubricants (liquid nitrogen) was conducted. Ministry approved CRO-SLO bilateral projects in the period 2010-2011. The research project is an important contribution to a PhD student and two students of postgraduate professional studies. Achievements have been published in the Journal of Mechanical Engineering (CC) and in the journal Technical Gazette (SCI-expanded). Experience of Hungarian colleagues from Kecskemet was helpful when using MQL equipment. MQL equipment was purchased from the German suppliers and activities planned for research in the field are being realized, especially in the factory Đuro Đaković. 54 Project coordinator: Professor Antun Stoić E-mail: [email protected] Phone: +385 35 446 188 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2008-2011 Programme type: National project ANNUAL REPORT 2010 Development of ERP System for Digital Factory Project results in year 2010: The research was conducted according to the set schedule of activities. The analysis of special demands in ERP (Enterprise Resource Planning) Systems for various types of production and service enterprises and types of production (metal processing, wood processing and construction) was done. Project coordinator: Professor Tomislav Šarić E-mail: [email protected] Phone: +385 35 493 444 Funding scheme: Ministry of Science, Education and Sports – Republic of Croatia Project duration: 2007-2011 Programme type: National project Material Resource Planning (MRP), which is a formal computerized approach to inventory planning, manufacturing scheduling, supplier scheduling and overall corporate planning, was used. Inventory planning for certain types of production, as well as modelling of multilevel component, which will be part of ERP system for different types of production with multilingual application, was done. The analysis of process planning, standardization of technological processes, tools and NC programmes for transfer of technological processes was done. A model for selection of optimal cutting parameters (cutting depth, feed rate, etc.) for the selected machine and type of most widely used materials in the metal processing industry was chosen. The criteria for choosing the most adequate supplier were suggested and analysed. There were two kinds of criteria: commercial criteria (price, delivery deadline, type of payment, meeting the delivery deadlines, complaints) and quality of the delivered goods. Multi-criteria decision making (MCDM) methods were used for choosing the suppliers. A model of basic planning of preparation and production capacities (with expected deadlines and costs according to achieved goals and expected duration) was investigated. The possibilities of defining a Maintenance plan for different equipment (by using different maintenance strategies) were investigated. A model for choosing a maintenance strategy was determined. It is based on Total Productive Maintenance, i.e. a management system for optimizing the productivity of manufacturing equipment through systematic equipment maintenance involving employees at all levels. The research results were published in scientific journals and at conferences. 55 ANNUAL REPORT 2010 Numerical Modelling of ConvectionDiffusion Phase Change Problems Project results in year 2010: Modelling of the transport phenomena occurring during solid/liquid phase change involves consideration of the fluid flow and heat and mass transfer processes. Special attention should be given to the treatment of the latent heat evolution because this term is a function of the temperature, as well as of the mixture concentration. This fact produces a strong coupling between the energy and species concentration equation and causes numerical instability problem. Generation of the algorithm for the calculation of velocity field, pressure and temperature field involves development of the mathematical model, development and implementation of the appropriate method for the simultaneous solving of the equations in the liquid and solid phase with prescribing the condition on the time dependent phase boundary. In the first phase of the project, the mathematical model for the simulation of a phase change process of the pure substances based on the enthalpy method is developed and a comparison of this model with the previously developed mathematical model, in which latent heat is considered through the source term of the energy equation, is performed. In the second phase, the numerical model is created and the new algorithm based on the enthalpy method and computer program are developed for the computation of phase change problem. During the third and fourth year of the duration of the project, the research area was based on the development of the mathematical model and computer program for the simulation of heat and mass transfer process in the binary mixture. The testing of the program is done and the comparison of the time dependent velocity and temperature field with results computed with commercial software and analysis of the natural convection driven by the temperature and concentration differences in the binary mixture are performed. Three papers have been published in Technical Gazette, Strojarstvo and Transaction of FAMENA and one article has been accepted for publishing in International Journal of Heat and Mass Transfer. Cooling of sphere due to natural convection Project coordinator: Professor Marija Živić E-mail: [email protected] Phone: +385 35 493 443 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 2007-2011 Programme type: National project 56 ANNUAL REPORT 2010 Submitted New Projects Instrument for Pre-Accession Assistance (IPA) – Component IIIC (Regional Development – Regional Competitiveness) Title of the action: Establishment of New Product Development Training Centre First name and surname of the legal representative of the institution: Prof. dr. sc. Milan Kljajin, Mechanical Engineering Faculty in Slavonski Brod Partner(s): Partner 1: University of Ljubljana, Faculty of Mechanical Engineering, Slovenia Associate(s): Associate 1: Technology Development Centre – Development Agency of Brod-Posavina County Ltd. (CTR), Slavonski Brod, Croatia Associate 2: METALLUM d.o.o., Slavonski Brod, Croatia Short description: Establishment of New Product Development Training Centre (NPDTC). Overall objective: To strengthen the overall competitiveness of Croatia and to contribute to sustainable regional development. Specific objective: To support development of HEI's innovation commercialization capacities thus enabling increase in economic activity and increase of employment in SMEs. Establishment of New Product Development Training Centre includes the following actions: adaptation of the facility, purchase and installation of planed equipment, training for using of equipment, capacity building and networking (capacity building for NPDTC staff and for SMEs), preparation of training materials, selection of participants, 15 different training workshops, establishment of regional network between HEI and SMEs, one regional conference on "Science-Technology-Business Networking and Collaboration" and one closing conference. Status of MEFSB (SFSB): Applicant 57 ANNUAL REPORT 2010 Title of the action: Open Lectures for Knowledge Based Industries First name and surname of the legal representative(s) of the institution: Prof. dr. sc. Goran Šimunović PhD Mech Eng Doc. dr. sc. Tomislav Galeta PhD Mech Eng, Mechanical Engineering Faculty in Slavonski Brod Partner(s): Department of Physics, J. J. Strossmayer University of Osijek Short description: To implement open and remote lectures at the Faculty in order to contribute to lifelong learning and sustainable regional development and industry competitiveness of SMEs. To select and publish those lectures from faculty syllabus closely related to innovation commercialization in public R&D and related to the enhancement of the science-industry/business collaboration as open lectures; To equip selected lectures and lecturers with necessary hardware and software; To provide additional top-level education of lecturers for selected subjects; To develop Internet web framework for registration, charging, notification and tracking of candidates; To develop the essential infrastructure necessary for open lectures and for remote learning; To educate lecturers for open lectures and for remote learning; To prepare legal bases for implementation of open lectures. Status of MEFSB (SFSB): Applicant 58 ANNUAL REPORT 2010 Title of the action: Centre for Foundry Technology - SIMET First name and surname of the legal representative of the institution: Doc. dr. sc. Ivan Brnardić – contact person Faculty of Metallurgy, Sisak Partner(s): University of Zagreb (Faculty of Metallurgy in Sisak), University of Osijek (Mechanical Engineering Faculty in Slavonski Brod), University of Zagreb (Faculty of Mechanical Engineering and NavalArchitecture) Associates: University of Zagreb (Faculty of Chemical Engineering and Technology), University of Ljubljana (Faculty of Natural Sciences and Engineering), University of Maribor (Faculty of Mechanical Engineering), Croatian Chamber of Economy, Sisak County Chamber Short description: The Project Centre for Foundry Technology-SIMET is designed to contribute to the overall competitiveness of the Croatian economy by focusing on development, manufacture and solving of technological problems for SME`s and industry in the field of metallurgy. Poor competitiveness of SME`s and industry in the region Panonska Hrvatska is related to insufficiently affirmative business climate and low impact of knowledge. According to that Project SIMET has 2 specific objectives; to enhance: 1) SME`s and industry competitiveness and concurrence by improving business potential and ensuring positive business climate, and 2) contribution of technology and R&D to economic development of SME's and industry in this sub-developed region. Action plan includes strenghtening of the research potential, R&D, technology-knowledge transfer and dissemination of project activities. Status of MEFSB (SFSB): Partner 59 ANNUAL REPORT 2010 Title of the action: Surface Engineering Centre (SEC) First name and surname of the legal representative(s) of the institution: Prof. dr. sc. Franjo Cajner, Faculty of Mechanical Engineering and Naval Architecture, Zagreb Applicant: University of Zagreb, Faculty of Mechanical Engineering and Naval Architecture Partners: Mechanical Engineering Faculty, Slavonski Brod Faculty of Engineering, Rijeka Institute of Metals and Technology, IMT, Ljubljana Short description: The overall idea of the Surface Engineering Centre is developing organisational and technical infrastructure in the engineering area in order to strengthen scientific, educational and economic activities through the establishment of a Surface Engineering Centre (SEC). The mission of the Surface Engineering Centre is to extend knowledge about the applicability and to improve performance by applying the procedures of surface engineering. Also, the primary activity of the Surface Engineering Centre is to educate our students, researchers and professionals dealing with these issues and through the scientific research to transfer the technological know-how to industrial practice. Status of MEFSB (SFSB): Partner 60 ANNUAL REPORT 2010 Title of the action: Set up of an innovation system in the Brod-Posavina County – Industrial Liaison Office of the Mechanical Engineering Faculty in Slavonski Brod First name and surname of the legal representative of the institution: dr. sc. Gabriele Gatti AREAScience Park of Trieste Applicant: Area Science Park, Italy Partner: Mechanical Engineering Faculty in Slavonski Brod Short description: The overall project objective is to contribute to sustainable regional development and industry growth and competitiveness in high value added sectors of economy and market in BrodPosavina County by means of: a) building technology transfer and innovation management and commercialization capacities in the Mechanical Engineering Faculty in Slavonski Brod of the J. J. Strossmayer University of Osijek (MEF); b) responding to the technology and innovation demand stemming from local enterprises. The specific project objectives will be centred around the design and start up of an innovative Industrial Liaison Office (ILO) at the Faculty as facilitator of the dialogue and interaction between academia and business. The total duration of the action is 18 months. The expected results are as follows: - to train a group of 3-4 skilled professionals in technology transfer management, in order to get the necessary professionalization on specialist subjects dealing with technical, economical, financial, IPR contents and to become the linking nodes between academia and market. - as far as the students at MEF are concerned, the start up of an ILO will allow them to have more opportunities of interaction with companies in the County, making them more competitive in terms of labour market (it is expected that 10-15 students will be involved in the above mentioned activities with companies every year, out of approximately 80 graduate and postgraduate students per year) - an increased collaboration between students and enterprises might lead to more innovative ideas brought on the market, thus contributing to improve SMEs competitiveness - as far as the professors at MEF are concerned, the ILO will provide them with information in terms of patents and protection of intellectual property and at the same time publicize to the 61 ANNUAL REPORT 2010 companies the results of their work and research, multiplying opportunities to develop joint activities and projects with industrial partners. It is expected that up to 50 professors will be involved in the above mentioned activities with companies every year (out of 74 Faculty members). Furthermore, the support of the ILO will contribute improving the technical capacities of the target group and of local partners (MEF, CTR and Industrial Park Nova Gradiška) in terms of enhanced skills for managing innovation and technology transfer as well as for approaching companies and researchers in Brod-Posavina County and surrounding counties. In terms of companies, they will benefit at the largest extent from the results of the project to start up the ILO at MEF, through the experimental model of services to be developed and delivered, based on a set of methodologies, techniques and tools well developed and consolidated which involve in a synergistic way academia and industry to set up an integrated system meant to valorise research results, to diffuse and apply innovation and to transfer technologies to SMEs. A set of criteria for the selection of companies will be established so to include local companies with a high growth potential: 80-100 companies will be contacted. As a result, out of the group of 30-40 companies that will be visited, 1520 ideas and needs for innovations will be identified. A maximum of 3-5 pilot innovation actions will then be selected and performed. Status of MEFSB (SFSB): Partner 62 ANNUAL REPORT 2010 Title of the action: Renewable Energy Sources Centre as an Incentive for Sustainable Development of Slavonija Region First name and surname of the legal representative of the institution: Prof. dr. sc. Damir Šljivac, Faculty of Electrical Engineering Osijek Applicant: Josip Juraj Strossmayer University of Osijek, Faculty of Electrical Engineering Osijek Partner 1: Josip Juraj Strossmayer University of Osijek, Faculty of Agriculture, Croatia Partner 2: Josip Juraj Strossmayer University of Osijek, Faculty of Mechanical Engineering, Croatia Short description: Overall objective of the proposed project is sustainable economic development in the region through industry competitiveness raising by knowledge and technology transfer and commercialization of project ideas. In order to achieve this goal in 18 months of project duration, project team prepared a set of activities which are designed to solve problems in the region regarding a gap between the needs of economy and the higher educational system, low environmental protection awareness, lack of information on renewable energy sources as well as on possible RES investments. Expected results of the project are as follows: Raised project management capacities (raised capacities for all Project partners in this type of Project); Founded knowledge and technology transfer centre for renewable energy (centre functioning and providing knowledge and skills for using renewable energy sources in agriculture, heat and electricity production); Established centres management and expert capacities (managers and experts that work in a centre); Raised energy efficiency and environment protection awareness (200 counselling hours, 200 people educated about the importance of using renewable energy sources). Status of MEFSB (SFSB): Partner 63 ANNUAL REPORT 2010 Accepted New Projects Instrument for Pre-Accession Assistance (IPA) – Component IIIC (Regional Development – Regional Competitiveness) Title of the action: Promoting the development of entrepreneurship based on innovation, knowledge and new technologies in Brod Posavina County TECHNOLOGY PARK / BISC Nova Gradiska The partners are: ? ? Agreement on co-financing the project was signed on 10 December 2010. ? Project is managed by: THE CITY OF NOVAGRADIŠKA ? The project aims: to contribute to sustainable regional development, to improve the competitiveness of the region, to create a system for the development of entrepreneurship based on innovation, knowledge and new technologies, and to create new jobs with higher added value. ? The planned results are: - the establishment and development of a multi-sector Technology Park for providing services to the business sector and the implementation of human resource development, - capacity building for the provision of business services related to research and development, innovation, knowledge and technology transfer, international business services, technology incubation, - development capacity for human resource development in new technologies. ? Action will have a direct positive impact on improving the competitiveness of the County and the Pannonian region for work and investment, sustainable regional development, and improving the investment potential and the potential for employment in the Region. The main activities are: - Establishment of a multi-sector Technology Park, - Supply and installation of equipment (IT, sophisticated training and productive machinery and equipment – CNC metal and wood processing, electrotechnics and electro machinery, solar technology), - Development of cooperation and networks among educational, R&D institutions, business sector and government units (implementation of the concept of Regional cluster), - Establishment of international cooperation and network in related area, Training of managerial and technical staff of the Applicant and its Partners (international business services, knowhow and technology transfer and business incubation), - Design and development of services relating to the new technologies, marketing and international business services, business/technology incubator services, engineering and technology services and training programmes. 64 ? ? ? Industrijski park Nova Gradiška d.o.o. za razvoj i ulaganje Strojarski fakultet Slavonski Brod (Sveučilište J. J. Strossmayera, Osijek) Conzorzio per l'AREA di ricerca scientifica e Technologica di Trieste AREA Science park, Italy Industrijsko-obrtnička škola Nova Gradiška Elektrotehnička škola Nova Gradiška Brodsko-posavska županija Hrvatska gospodarska komora Županijska komora Slavonski Brod Obrtnička komora Brodsko-posavske županije Regionalna razvojna agencija, IAL FVG, Italy. ANNUAL REPORT 2010 The target groups of project beneficiaries: - small and medium-sized enterprises (existing small and medium-sized businesses, start-up companies, new investors), as potential users of business and technology services, - students, artisans and workers in the field of training programmes. Availability of new services and improved quality of the workforce will increase competitiveness, development and investment potential of the business sector, contributing to the preservation of existing jobs and creating new jobs of higher added value and to attraction of new investment of higher technological levels in Industrial / Technology Park Nova Gradiska. It is planned that the Project (within the 5-year period) will support the establishment and development of 30 new technologyoriented companies, attracting 10 new investments in the Industrial / Technology Park, and directly support the creation of 400 new jobs of higher added value. The project will also have a positive impact on the preservation of existing jobs that are in danger because of technological obsolescence and outdated skills. Action is based on the idea that innovation is a key factor for stimulating economic growth and increased competitiveness and the fact that the attractiveness, value and competitiveness rely on the well-developed and developing research infrastructure, highly skilled workforce and diffused culture of innovation. Total project cost amounts to 1.146.591,93 € and the European Union will co-finance 802.614,35 €. 65 ANNUAL REPORT 2010 Junior Researchers Nataša Veljić Institution: Faculty of Mechanical Engineering, University of Zenica, Republic of Bosnia and Herzegovina Cooperation Agreement (signed on 4 December 2009) Study stay: 10 May – 10 June 2010 Nataša Veljić visited Faculty of Mechanical Engineering, University of Zenica (Chair for Energy and Process Engineering) where she acquired new knowledge, and investigated research possibilities for her PhD thesis. She mastered a number of tutorials for the use of computational fluid dynamics (FLUENT software) which can be used for her PhD thesis (laminar and turbulent flow, heat transfer by conduction, convection, radiation, generating of grids for different geometries). Furthermore, Nataša Veljić visited modern laboratories of Chair for Energy and Process Engineering, and attended lectures in the field of Kinematics and Fluid Dynamics. This study stay was very useful because she was given the opportunity to research and study in detail the fund of the library (PhD theses, data bases, etc.) at Faculty of Mechanical Engineering. This kind of study stay can help in establishing new contacts and future scientific cooperation between the faculties. Different equipment at laboratory of the Chair for Energy and Process Engineering (Faculty of Mechanical Engineering, University of Zenica ) 66 ANNUAL REPORT 2010 Josip Stojšić Institution: Kecskemét College, Faculty of Mechanical Engineering and Automation, Department of Rubber and Polymer Technology. Kecskemét, Hungary Erasmus Mobility Programme in academic year 2010/2011 Study stay: 15 October 2010 – 15 January 2011 In the time period of 15 October 2010 – 15 January 2011, Josip Stojšić visited the Department of Rubber and Polymer Technology at Faculty of Mechanical Engineering and Automation as an Erasmus student. During the study stay and under the supervision of prof.dr.sc. Károly Belina, Josip Stojšić had the opportunity to work at one of the best-equipped laboratories for polymer processing in Europe. In the first part of the three-month period, Stojšić studied the basics of the rheological calculations and measurements with online extruder and capillary rheometer. He also learned how to control the injection moulding machine with instrumented injection moulds for measuring the cavity pressure as a function of the process parameters. This study visit was a valuable experience and a chance to become acquainted with the modern technologies. Furthermore, it was also useful for establishing new contacts and future scientific cooperation between two faculties. 67 ANNUAL REPORT 2010 Defended PhD Theses Mirko Karakašić PhD Thesis: Connection Model of Product Functions, Parameters and their Value Intervals in Product Development, by Using Function and Functionality Matrix Model povezivanja funkcija proizvoda, parametara i njihovih intervala vrijednosti kod razvoja proizvoda, primjenom matrice funkcije i funkcionalnosti Summary: After ground and motivation for research, this doctoral thesis shows theoretical basements that form exploration background for research represented with this thesis. By representation theory of technical systems, design process, functional modelling, design catalogues and matrix methods, short region review remarkable for this research was presented. Criteria, by which products, functions and functionalities are defined, are listed in this thesis. Function definition criteria should contribute to better understanding and leading of design process on abstract level. First and second structural form of function and functionality matrix model is developed. By developed mathematical model, functions and functionalities are interrelated. Functionalities solve defined functions. Functions are described by parameters and their interval values. In this way, functions are unambiguously described. Property of sub-matrix appears inside the matrix model. Relations between functions and functionalities are achieved by links inside sub-matrix. Product matrix structure is realised by binding functions that interrelate first and second structural form of function and functionality matrix models. Matrix structure is the basis for generation of shape (physical) of product structure. Detail function structure is the basis for generation of first and second structural form of function and functionality matrix. Relation between levels of detail function structure, matrix structure and hierarchical tree shaped product structure is explained. Matrix models are implemented in developed computer Web application. Building blocks present simple technical systems. They are described by functions and stored in central MySQL database of developed computer application. Matrix model and computer Web application are tested then on concrete products. Date of defence: March 12, 2010 Examination Committee: Prof. dr.s c. Ivan Samardžić, Chair Prof. dr. sc. Milan Kljajin, Mentor Prof. dr. sc. Jožef Duhovnik, Faculty of Mechanical Engineering, University of Ljubljana, Slovenia, Member Prof. dr. sc. Franjo Matejiček, Member Prof. dr. sc. Milan Opalić, Faculty of Mechanical Engineering and Naval Architecture in Zagreb, Member Mirko Karakašić during the dissertation defence Examination Committee 68 ANNUAL REPORT 2010 Model of the first structural form of the function and functionality matrix Function and functionality matrix generated in developed computer Web application 69 ANNUAL REPORT 2010 Pejo Konjatić PhD Thesis: Analysis of Influence of Weld Geometry and Mechanical Properties of Weld Materials in the Weld on Fracture Behaviour of Repaired Welded Joint Analiza utjecaja geometrije zavara i mehaničkih svojstava materijala u zavaru na lomno ponašanje repariranog zavarenog spoja Summary: This dissertation deals with investigation of the influence of geometry and mechanical properties of weld material in the weld to fracture behaviour of welded joint. The research was primarily focused on repaired welded joints where there is heterogeneity in terms of differences of mechanical properties of weld material. In addition to investigating heterogeneity, an investigation of influence of flaw size, i.e. crack in a heterogeneous welded joint, was also performed. In the introductory chapter, a detailed definition of the investigated problem is described, as well as previous and current research relevant to issues of fracture behaviour of welded joints. Likewise, a short overview of the beginning and importance of further development of procedures for assessing the integrity of the structures without welds, as well as for assessment of welded structures is given, with emphasis on the necessity of developing the procedures containing modules for heterogeneous welded joints. The main and auxiliary dissertation hypotheses are stated, related to investigated problem. For acceptance or rejection of the hypothesis, guidance in research is defined. Scientific methods to be used in this research are described and expected scientific contribution is given. In further sections, a problem of crack occurrence in welded joints is described and importance of reparations in the repair welding of welded joints is briefly explained, followed by an overview of the basics of the theory of Date of defence: May 7, 2010 Examination Committee: Prof. dr. sc. Ivan Samardžić, Chair Prof. dr. sc. Franjo Matejiček, Mentor Prof. dr. sc. Dražan Kozak, Member Prof. dr. sc. Nenad Gubeljak, Faculty of Mechanical Engineering, University of Maribor, Slovenia, Member Prof. dr. sc. Dragomir Krumes, Member Pejo Konjatić after PhD conferment Examination Committee 70 ANNUAL REPORT 2010 plasticity with emphasis on the analytical method of slip line field analysis for determination of the limit load causing plastic collapse of structures. The development and procedure of the often used integrity assessment methods are also described. At the end of the first part of the dissertation, application of finite element method in elastic-plastic fracture mechanics is described. Carried out analytical and numerical investigations on standard fracture mechanics three-point bend specimen were described in the following sections of this work. A numerical model for finite element analysis is generated, verified using analytical methods of slip line field and compared with results of previous research done on welds with the weld strength higher or lower than strength of base material of weld joint. An additional material with certain degree of strength mis-match to the base material was implemented in verified numerical model. The model's geometrical parameters, the size of the cracks and the strength mis-match factors of materials present in the weld are systematically varied in order to determine their influence on fracture behaviour of repaired welded joint. Primarily, determination of yield loads was carried out i.e. determination of force which causes plastic yielding of the whole net section of the weld inducing plastic collapse. For different configurations of weld geometry and materials present in weld, a compendium of yield loads for heterogeneous welded joint is derived. Results of performed analysis are graphically displayed and presented in tables and using statistical processing and analysing results mathematical models that properly describe the fracture behaviour of weld, depending on the influential mechanical and geometrical parameters are defined, either if crack is located in stronger or in weaker part of weld considering strength of materials. At the end, a several examples of structural integrity assessments of the homogeneous and heterogeneous weld using SINTAP procedure were done, which has not been done so far because of the lack of any force compendia solutions for yield load of heterogeneous welded joints. Numerical model of heterogeneous welded joint Flow field of material of heterogeneous welded joint with fracture in the material with lower strength than the strength of base material 71 ANNUAL REPORT 2010 Andrijana Milinović PhD Thesis: Research of Boride Layers Formation Kinetics on Carbon Steels Istraživanje kinetike nastanka boridnih slojeva na nelegiranim čelicima Summary: In this study, the influence of boronizing parameters (temperature and duration) and chemical composition of carbon steels on kinetics of creation of boride layers is explored. Also analyzed are cross sectional changes of contents of boride phase and hardness of layer. Overview of researches conducted so far in the field of boronizing is given in introduction. After laying down reasons and motivation that initiated this study, all planned activities and scientific methods to be used are given. Regarding scientific research issues, hypotheses are defined and expected scientific contribution is stated. In continuation of this study, theoretical basics of boronizing procedures and diffusion of atoms in solids are provided. Within experimental part of this study, design of experiment is described according to which procedure of boronizing in a solid agent is conducted. Boronizing is conducted on three carbon steels (C15, C45 and C70W2) under different conditions regarding temperature and duration of boronizing. Microstructure has been analyzed within metallographic examinations. Through usage of linear method, average thicknesses of boride layers are determined. Also analyzed is the change of volume share of boride phase concerning cross section of the layer. Based on volume share of boride phase as well as measured hardnesses of base material and boride phase, change of cross sectional layer hardnesses is determined and analyzed. Analysis showed that variation of boronizing parameters as well as chemical composition of carbon steel influence on volume share of boride phase and hardness concerning cross section of layer. Date of defence: July 14, 2010 Examination Committee: Prof. dr. sc. Dražan Kozak, Chair Prof. dr. sc. Dragomir Krumes, Mentor Prof. dr. sc. Božidar Matijević, Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, Member Prof. dr. sc. Vlatko Marušić, Member Prof. dr. sc. Ivica Kladarić, Member Pejo Konjatić, Andrijana Milinović and Daniel Novoselović after PhD conferment Examination Committee 72 ANNUAL REPORT 2010 a) In continuation, through application of basic laws of diffusion, values of frequency factors and activation energy, concerning boron diffusion into examined steels, have been determined. Analysis has shown functional correlation between these values and chemical composition of carbon steel. Mathematical models discovered enable determination of values of activation energy and frequency factors based on content of carbon within carbon steel. Through use of statistic methods, in further continuation of this study, the influence of temperature and duration of boronizing, as well as the chemical composition of steel, is analyzed with respect to average thickness of boride layer, thickness of the compact part of layer and its tootheness. Analysis showed existence of influence of mentioned factors upon observed properties of boride layer, and as a result, mathematical models showing their functional correlation have been obtained. b) c) Microstructures of boride layers at ϑ = 920 ºC, t = 8 h, magnification 200 : 1: a) C15 Steel, b) C45 Steel and c) C70W2 Steel 73 ANNUAL REPORT 2010 Daniel Novoselović PhD Thesis: Influence of Technological Parameters on Residual Stresses in Pressure Die Casting Utjecaj tehnoloških parametara na zaostala naprezanja pri tlačnom lijevanju odljevaka Summary: This dissertation deals with research of the influence of technological parameters on residual stresses in pressure die castings. The motivation for the research was given in the introduction, where it is evident that the production of aluminium alloy castings is growing and that mostly used technology for production is pressure die casting. This technology is very complex with many technological parameters which can cause defects on the castings (distortions and cracks in castings), which are often consequence of residual stresses. Reviews of previous research show that influences of technological parameters on residual stresses in pressure die casting are not thoroughly investigated, so this phenomenon has been investigated. The reason for occurrence of residual stresses in castings, types of stresses, possibility of their determination and removal were analyzed. Technology of pressure die casting was described and the technology parameters, which can have influence on occurrence of residual stress in castings, were also analyzed. After the most influencing technological parameters were selected, research was performed in two directions: - determination of residual stresses with the computer simulation - calculation of residual stresses based on the measured strain. Date of defence: July 16, 2010 Examination committee Prof. dr. sc. Dražan Kozak, Chair Prof. dr. sc. Ivan Budić, Mentor Prof. dr. sc. Pero Raos, Member Prof. dr. sc. Branko Grizelj, Member Prof. dr. sc. Faruk Unkić, Faculty of Metallurgy, University of Zagreb, Member Daniel Novoselović during the dissertation defence Examination Committee 74 ANNUAL REPORT 2010 The normal stresses in the direction of axis X Shape of the casting was selected and computer simulations, with different values of influence of technological parameters, were carried out. Computer simulations have been carried out according to the research plan with software MAGMAsoft in the foundry P. P. C. Buzet, d. o. o. in Buzet. To validate the results of computer simulation, test samples were cast in operating conditions in the foundry LIPOVICA d. o. o. - Popovača. The strains in test castings were measured by "hole-drilling method". They are used to calculate equivalent residual stress. Based on the results, functional dependence is defined, and diagrams of influence of technological parameters on the equivalent residual stresses are made. After comparing the results, conclusions of the dissertation were adopted, and further research was suggested. The normal stresses in the direction of axis Z Test castings casted accordingly to plan of experiments The eqivalent stresses by von Mises The results of simulation of residual stresses for V01 (Ju = 670 °C; vII faze = 1,67 m/s; pIII faze = 188 bar) Analysis of the measuring results by the standard ASTM E 837-01 method 75 ANNUAL REPORT 2010 University Specialists of Mechanical Engineering Atila Čizmar Title: Preparation, Evaluation and Monitoring of Distribution Pipeline Project Priprema, vrednovanje i praćenje projekata izgradnje distribucijskih plinovoda Summary: Regular supply of consumers with natural gas depends on the construction of new and expanding of existing pipeline network. To achieve continuity in the construction of gas pipeline networks and to satisfy the numerous demands and obligations that the company has, it is necessary to deal with reliable and complete information, and based on this information to make a high quality building plan which is always limited by funding and available resources. In this work, an insight into the importance of the project during the life cycle, as well as the importance of managing the project is presented. Construction of distribution gas pipelines belongs to investment projects in whose construction direct and indirect participants are involved, where the rights and obligations of participants are regulated by legislation, treaties, standards and profession rules. When making a decision on the construction, it is necessary to evaluate and assess the project, and to take into account the socio-economic value that the project brings. Furthermore, an insight into some areas of artificial intelligence that is used in preparation and decision making is provided. Finally, the work includes a brief overview of monitoring project realization and proposals for improving the monitoring of the project for construction of distribution gas pipelines. To solve the decision problem, an expert system has been used – Expertrule Knowledge Builder of the manufacturer Expertrule Software. Selected qualitative and quantitative criteria determine the significance in the model of multicriteria evaluation. In this way, the impact of criteria on the total project evaluation changes in accordance with the real conditions in the company and the environment and gives priority to the realization of one of the monitored projects. The aim of this specialist work is to achieve an objective decision supported by artificial intelligence and by using this kind of analysis and preparation, the investor reduces the risk of investments, eliminates subjectivity of decision making and increases efficiency and reduces preparation time of construction of distribution gas pipelines. 76 Date of defence: July 13, 2010 Examination Committee: Prof. dr. sc. Marija Živić, Chair Prof. dr. sc. Goran Šimunović, Mentor Prof. dr. sc. Roberto Lujić, Member ANNUAL REPORT 2010 Tomislav Draganjac Title: IZBOR DOBAVLJAČA CIJENA ISPORUKA DOBAVLJAČ 1 PARITET DOBAVLJAČ 2 PAKIRANJE PLAĆANJE DOBAVLJAČ 3 AHP model for supplier selection Date of defence: November 8, 2010 Examination Committee Prof. dr. sc. Ivica Kladarić, Chair Prof. dr. sc. Katica Šimunović, Mentor Prof. dr. sc. Roberto Lujić, Member Application of Advanced Methods in Inventory Control and Classification Primjena suvremenih metoda u upravljanju i klasifikaciji zaliha Summary: In this work, with the aim of efficient inventory management, multicriteria inventory classification and criteria have been proposed. Based on proposed criteria and multicriteria inventory classification, using the methodology of analytic hierarchy process (AHP), it has been proven that the use of only one criterion – annual cost (according to traditional ABC classification), does not provide a reliable classification, but with the multicriteria approach reliable decision can be made. According to the traditional ABC classification, the items with relatively low costs belong to the group C, but by the inclusion of the proposed criteria of criticality and delivery time, these items are among the group A and B, because of relatively high critical factor and longer delivery time. The items which deserve close attention are unambiguously defined by the multicriteria approach, so the multicriteria approach to supplier selection for those items makes sense. Considering the different production conditions, various criteria for the supplier selection can be defined; therefore, according to the specificity in the company Same Deutz Fahr Žetelice d.o.o. the following criteria are proposed: price, parity, postponing payment, packing and delivery. After the defined criteria, weights and local priorities of supplier are obtained, using the AHP methodology. Finally, the suppliers are ranked. In this work, except the application of AHP methodology, the possibility of supplier evaluation using an expert system was discussed. These two approaches are compared and it is concluded that the AHP supplier selection model could be effectively integrated with the proposed AHP multicriteria inventory classification model into the inventory and warehouse modules of ERP system, with the main goal of automatic selection of A group items and further the selection of supplier. However, in many Croatian companies, the supplier selection is based on the sum of score of the criteria and the expert system, as an independent decision support (not integrated into the information system of the company), could also be applicable. 77 ANNUAL REPORT 2010 Ilija Džepina Title: Choice of Induction Hardening Parameters of Sheaves of Dredgers Izbor parametara indukcijskog kaljenja utora lijevanih užnica jaružara Summary: In this paper, a choice of heat treatment parameters of sheaves, method of determination of surface errors and sanation of surface damages is comprised. On test samples that are made from the same material (GS30Mn5), trials of welding are made (SMAW procedure) by fluting of prepared damaged places. After that, induction hardening is performed with different parameters. Control of crack appearance is determined by magnetic method. With recording of cross section structure and measuring of hardness, it is determined that apart from corresponding input of energy (electricity frequency) the properties of sheave surface layer also depend on coolant choice. Satisfactory hardness (320÷400 HB) is achieved with the combination of air cooling and water with simultaneous avoidance of cracks. This choice of parameters should provide satisfactory operating life of wires (hardness 500÷550 HB) and safe exploitation of dredgers. Inductor with air and water coolant Induction hardening of sheaves Characteristic microstructure of HAZ / weld Date of defence: December 13, 2010 Dredger 78 Examination Committee: Prof. dr. sc. Ivan Samardžić, Chair Prof. dr. sc. Vlatko Marušić, Mentor Prof. dr. sc. Tomislav Šarić, Member ANNUAL REPORT 2010 Activities of Departments Department for Mechanical Design The activities of the Department for Mechanical Design include the complete analysis during development and design of the product: structure design by using CAD tools, calculation and analysis of structures by using analytic expressions and numeric methods (usually FEM) with structure optimisation and development of different methods for evaluation of single design solutions, experimental analysis of finished products and models through planning of experiments, research and processing models of experiments. Scientific-research work of the Department and the cooperation with the economy are the basis for improving the education process. As the result of scientific-research work, many papers were published in scientific and professional journals, as well as in numerous proceeding books at international conferences. Scientific research of the Department was used as the basis for a number of final papers and PhD dissertations. The members of the Department are involved in solving numerous problems that occur in the process of design, production and exploitation in different production companies. The Department offers the following services: • • • revision of calculations and projects expertise of design and different fractures testing redesign of products and development of products, etc., by using the computers, test equipment and adequate programmes that exist at the Faculty. The following Laboratories are part of the Department and they are used for educational purposes, scientific-research work and cooperation with the economy: 1. 2. 3. 4. 5. Laboratory for Mechanical Design Laboratory for Mechanical Testing Laboratory for Engines and Motor Vehicles Laboratory for Electrical Engineering Computer Classroom ĐĐ The Department uses the equipment from these laboratories, as well as the equipment from other Departments and institutions (due to cooperation programme LECAD Group and other forms of cooperation). The Laboratory for Mechanical Design is used for classic measuring: deformation, stress, force, displacement, velocity, acceleration, pressure, etc. The measuring can be static or variable. Next to test equipment, there are also computers used for data processing. The testing can be done in the laboratory on real models, as well as on the work site on real objects: machines, vehicles, plants, steel structures, etc. 79 ANNUAL REPORT 2010 The Laboratory equipment includes: VibroMetTM 500V Laser Doppler Vibrometer The VibroMetTM 500V Laser Doppler Vibrometer measures the velocity and frequency of vibration at a point of vibrating target. It can also be used for measuring displacement and acceleration. Both of these parameters can be obtained in software by direct integration and derivation of the velocity. For good reflecting surfaces the VibroMet™ 500V can measure targets at any distance between 1 cm and 5 meters. It can measure frequencies from DC to 20 kHz. Velocity of vibration has a maximum value of 1,0 m/s. The VibroMetTM 500V consists of a remote laser sensor head and an electronic controller. The remote laser sensor head includes an infrared laser diode for measurement, a red laser diode for aiming, an acousto-optic modulator and a high sensitivity photo-detector. The electronic controller has both a demodulated velocity output and a 10,7 MHz frequency modulated signal output. The second laser is a red 650 nm laser that can be turned on and off by a switch on the back of the laser head. This red laser is used to see where the measurement is being taken. Both displacement and acceleration can be obtained in the software by direct integration and derivation of the velocity. The VibroMetTM 500V is ideal for measuring vibration on reflective surfaces. For less reflective surfaces, it is easy to increase the reflectivity of the surface with white or retro-reflective paint or paper. The front of the controller has a signal strength indicator, two selectable velocity ranges and an array of low pass filter options (1, 2, 5, 10, 20 kHz), which can be used for lifting S/N spectral strips. Velocity and frequency data of an automobile engine as the RPMs are ramped up. Characterizing automotive engines to quantify vehicle noise & vibrations. 80 Benefits - Non-contact measurements without mass loading - High temperature measurements - Vibration measurement on rotating parts - Easy-to-use Point & Measure Operation - Ultra high sensitivity. ANNUAL REPORT 2010 Measuring amplifier HBM-MGCplus ABx22A Measuring amplifier HBM-MGCplus AB×22A has 24 measuring channels with 0,05 accuracy. The number of measuring channels is 2×8 for measuring with full, half and quarter bridge for electric resistance measuring strips, SG. There are also 4 piezo sensors (with power supply) that can be used for measuring. Measuring can be done by using 4 induction sensors (LVDT and B12). Measuring amplifier can be used for measuring: deformation, stress, force, displacement, velocity, acceleration, pressure, etc. Measuring can be either static or variable. Measuring can be done on the machines, vehicles, plants, steel structures, etc. Measuring amplifier HBM-MGCplus ABx22A with 24 measuring channels Force measurement during turning 81 ANNUAL REPORT 2010 The Laboratory for Mechanical Testing uses the following equipment for analysis of crack propagation: Microscope for monitoring of crack propagation With the Leica MZ12.5 stereomicroscope, both high relief and flat specimens, are observed in large fields of view and then magnified continuously in one motion from 8× to 100× (total magnification 4× to 640×). The microscope is used for measuring of parameters (CMOD and CTOD) in fracture mechanics, for recording of crack propagation on the samples, the structure of sample surface, etc. Microscope for monitoring and recording of crack propagation (mounted to a tensile tester). The Laboratory for Engines and Motor Vehicles deals with testing of (smaller) engines, in order to monitor ecologically sensitive parameters. The testing can be done in laboratory conditions, as well as on the work site. Laboratory testing includes: characteristic Diesel engines in agricultural machinery. The composition of exhaust gases (classical Diesel engines and biodiesel engines) is measured. The testing of engines can be done in the working conditions (in the companies that use them) with simultaneous monitoring of Diesel engines (that operate on fuel oil, biodiesel with 20-30 % of biocomponent, and pure biodiesel). Degradation of oil viscosity quality (due to motor operation) can be observed in laboratory conditions and during exploitation. The test equipment used for these purposes can be found in the Laboratory and ĐĐ Institute Laboratory.. 82 Moment of inertia measuring instrument ANNUAL REPORT 2010 Injector pressure measuring instrument Power unit HATZ The equipment of the Laboratory for Engines and Motor Vehicles: ? Training power unit HATZ: Diesel engine 1B20 with 220V AC generator ? Digital portable revolutions gauge TESTO 470 ? Non-contact thermometer TEST Quicktemp 825-T2 ? Measuring device BAR 928H for constant measuring of air pressure, temperature and humidity in the environment ? Device for measuring exhaust gases TESTO 300M ? Device for measuring carbon dioxide and carbon monoxide JUNKALOR INFRALYT 1102 ? Device for measuring of injector pressure BOSCH EPS 1000 ? Device for measuring of inertia of rotating parts of engines and vehicles ? Compressor (5 bar) ? Set of pneumatic tools (for pressure up to 5 bar). Laboratory for electrical engineering is used primarily for classical testing in the field of electrical engineering. The laboratory equipment includes: analogue voltmeters for AC/DC, analogue ammeters for AC/DC, current and voltage regulation sources for laboratory purposes, infrared thermometer, electrostatic fieldmeter, solarimeter, etc. Kimo Kiray 300 Infrared Thermometer Infrared thermometer Kiray 300 is a thermometer used to diagnose, inspect and check any temperature. Thanks to its elaborated optical system with a dual laser sighting, it allows easy and accurate measurements of little distant targets. The Kiray 300 instrument has an internal memory which can save up to 100 measurements. Infrared thermometer can measure the surface temperature of an object and thermal image of certain parts of industrial equipment or walls / windows can be obtained and used for the analysis of energy efficiency of objects. Its optic lens catches the energy emitted and reflected by the object. This energy is collected and focused onto a detector. This information is displayed as temperature. Temperature range is from -50 to +1850 °C. This device meets with following standards' requirements: ? EN 50081-1 : 1992, Electromagnetic compatibility, Part 1 ? EN 50082-1 : 1992, Electromagnetic compatibility, Part 2 ? Compressor FMX-003 Electrostatic Fieldmeter Exhaust gas measuring instrument SIMCO FMX-003 fieldmeter is a compact eletrostatic fieldmeter used for locating and measuring static charges. The FMX-003 measures static voltages within ±20 kV (20.000 V) at a distance of 25 mm. Results are simultaneously displayed numerically and in bar graph format. The conductive case and ground snap facilitate grounding for accurate measurement. The circuitry of the FMX003 has been designed to make measurements in areas using air ionization. 83 ANNUAL REPORT 2010 Kimo SL200 Solarimeter The portable autonomous solarimeter measures the solar irrigation for the control of photovoltaic and thermal installations on site. Solar irrigation measuring range is from 1 W/m2 to 1300 W/m2. Accuracy is 5 % of measurement. Spectral response of the instrument is for electromagnetic waves from 400 to 1100 nm. FMX-003 Electrostatic Fieldmeter Kimo SL200 Solarimeter Kimo Kiray 300 Infrared Thermometer 84 ANNUAL REPORT 2010 Computer classroom ĐĐ (with 21 seats) is equipped with state of the art IT equipment (Lenovo computers) and it is used for educating students (future mechanical engineers). It can be used for different programme systems: drawing, modelling, design, etc. Computer classroom ĐĐ 85 ANNUAL REPORT 2010 Department for Production Engineering The Department for Production Engineering conducts scientific research in the field of production procedures and modern mechanical engineering technologies. This Department consists of three chairs: Chair for Casting and Metal Forming, Chair for Machining and Polymers Processing, Chair for Welding and Surface Protection. The Department has 13 staff members (4 full professors with tenure, 1 full professor, 1 associate professor, 1 assistant professor, 5 junior researchers / assistants, 1 senior associate). Scientific and research activities Department for Production Engineering is involved in 4 national scientific research projects (financed by the Ministry of Science, Education and Sports), and several bilateral international projects of cooperation with the economy. Ultrasound measuring device for the control of parent material and welded joints homogeneity Chair for Casting and Metal Forming The scientific-research activity of the Chair for Casting was focused on the investigation of influence of technologic parameters on the residual stresses in pressure castings. The following was investigated: the influence of the most important technologic parameters, the temperature of casting, the rate of filling the mould with an alloy, increase of pressure in the filled mould, and the rate of cooling of the injection system after removing it from the mould. Residual stresses were tested on the measuring instrument MTS3000 in the Laboratory for Casting. Chair for Machining and Polymer Processing The research is focused on the following areas: rapid prototyping (RP), non-traditional and ecologically acceptable treatment procedures, as well as the traditional treatment procedures. Part of the rapid prototyping research is the analysis and systematisation of RP procedures and rapid tooling (RT) based on the shape of the basis material, the mechanism of forming and the type of procedure. The main characteristics, advantages and disadvantages of certain procedures are analysed. The use of RP and RT in engineering and medicine are investigated in detail. A number of products was designed and technologically produced by using the computer for rapid prototyping by 3D printing, and the hybrid procedure (OBJET) and the STL files were prepared. Design characteristics of all the selected products were analysed in detail (based on the type of procedure). The influence of moulds made by rapid prototyping, i.e. material, on the characteristics of the final product (cast) is investigated. Therefore, the prototype moulds were made by chip-forming and rapid prototyping. By adapting the existing software (Moldex and CadMould), the possibilities of computer simulation of injection pressing were tested on the moulds made by RP. The possibilities of RP of individual medical implants (custom made implants) are being extensively investigated. Medical CTs and MRIs are processed by using the computer software 3D Doctor in order to make CAD 86 Optical gauge for control of tool geometry DISA PNZ device ANNUAL REPORT 2010 medical models as the basis for making RP implants. Based on these models, the characteristics of making implants by using 3DP and OBJET were tested. The investigations of RP of implants made of bio-compatible materials are also being conducted. HBM MTS3000 device Test equipment for testing characteristics of sand for moulds Universal lathe TNP 160 A Investigations of non-traditional procedures (abrasive jet cutting, laser cutting, and smoothing) are done in order to optimise technologic parameters concerning the quality of the cut (microgeometry of the surface) and the effect of cutting (additional finishing procedures). The following instruments are used: instrument for measuring roughness, cameras for monitoring the curvature of the cut line and other types of measuring instruments. As a part of ecologically acceptable treatment procedures, the following is investigated: the possibility of MQL procedure, cryogenic treatments (using of liquid nitrogen for cooling), and dry treatment (without the cooling agent). The following was investigated: cutting forces, vibrations, roughness of the treated surface, tool wear. The testing equipment consists of: equipment for MQL, measuring multi-channel amplifiers, sensors (tensometric for forces, and induction for accelerations), instrument for measuring roughness, and microscopes for measuring tool wear. These investigations also include the quality testing of the applied SHIP (pH, oil concentration in emulsions, impurities). Traditional treatments are focused on the analysis of fracture and geometry of particles, RP cutting and shear angle. The investigations also include the dynamics of the cutting procedure (variable conditions of cutting due to variable geometry or structure). FFT analysis is also done, as well as setting of referent frequency domains for certain cases. Forces of cutting and vibrations are investigated. Measuring instruments are: multichannel amplifiers, sensors (tensometric for forces, and induction for accelerations), software for FFT analysis and geometry analysis from digital images of particles. Chair for Welding and Surface Protection 34 papers were published in 2010 as a part of the project "Modern technologies of joining light engineering structures" (1521521473-1476). Head of the project is prof. dr. sc. Ivan Samardžić. Members of the Chair have also published 3 papers in cooperation with heads of other projects. In 2010, the results of testing in the field of welding technology application, surface material protection and in the field of introduction of integrated management systems in Croatian companies were published in scientific journals and in conference proceedings. ISO 9001, ISO 14001 and ISO 22000 Standards were used for these investigations. Laboratories Due to the complex field of expertise, this Department has 7 laboratories that are used for education, scientific and research activities, as well as for cooperation with the economy: Band saw 87 ANNUAL REPORT 2010 1. Laboratory for Quality Control andAssurance 2. Laboratory for Casting and Design of Manufacturing Processes 3. Laboratory for Machining 4. Laboratory for Polymer Processing 5. Laboratory for Materials Surface Protection 6. Laboratory for Welding 7. Laboratory for Metal Forming, Tools and Instruments Laboratory for Quality Control and Assurance offers the following services: control of homogeneity of parent material and welded joints, control of geometry of chip-forming machining tools, control of temperature, humidity, electrical units (voltage, current intensity, el. resistance), length, bore diameter. CADMOULD 6 The Laboratory equipment: ultrasound measuring instrument for the control of parent material and welded joints homogeneity, optical gauge for geometry control of the chip-forming machining tools, measuring devices for the control of temperature, humidity, electrical units (voltage, current intensity, electrical resistance), length, bore diameter. Laboratory for Casting and Design of Manufacturing Processes This Laboratory is used in the education process (undergraduate and graduate programme) for the courses dealing with the casting technology in order to make students familiar with the casting production. It is possible to conduct testing that can be used for writing scientific and professional papers, as well as final and term papers. The Laboratory has the following equipment: recondensing strength measuring device DISA PNZ, residual stress measuring device HBM MTS3000, test equipment for testing characteristics of mould mixtures. The Laboratory can provide certain services of testing sand for making moulds and measuring residual stresses in castings. There is also a computer with 'Solid Cast' software for monitoring the simulation of the hardening process, so that causes for defects on the castings can be removed before beginning of production. Laboratory for Machining has 30 m2 of floor area. The primary function of the Laboratory is education, including testing needed for writing term and final papers, as well as scientific research work, and doctoral theses. The most important research activities are: introduction of modern technological processes and cutting tools in the production, improving the process of chip-forming machining (with respect to ecology), control of cutting tools (to achieve better cutting characteristics), analysis of chip-forming cycle, control and optimisation of technological parameters of treatment and dynamic measuring of cutting forces, noise and acceleration in the process of chipforming machining. The Laboratory includes the following 88 Simulation of polymer joint (ANSYS) Corrosion testing in artificial atmosphere Testing of protection coating characteristics ANNUAL REPORT 2010 equipment: universal lathe TNP 160 A (Figure 6), band saw, device for electro-erosion, equipment for collecting technological parameters, device for measuring wear of the tool cutting edge, device for controlling the driving engine on machines, device for simulation of the tool cutting edge sharpening, and other measuring equipment and tools. Laboratory for Polymer Processing is used for education purposes, as well as for scientific-research projects, and cooperation with the economy in the field of polymer processing and modern joining procedures. Automatic tracking vehicle FTV 4 Motoman arc welding robot with welding positioner Laboratory has 30 m2 of floor area. Part of Laboratory testing is: identification of polymer materials, simulation of rheologic processes in the mould cavity at injection pressing, design of polymer products, moulds and tools by using analytic and numeric methods, and especially testing of sealed joints. Laboratory equipment includes: specialized software, e.g. CADMOULD 6 (programme for analysis of mould filling and simulation of rheologic processes in the mould cavity at injection pressing of polymers), 3D DOCTOR (software for processing of medical images), CAMPUS (data base of polymer materials), ANSYS (software for analysis of structures by using FEM). Laboratory for Materials Surface Protection deals with corrosion testing and protection of engineering materials. The Laboratory offers a number of possibilities: corrosion testing in artificial atmospheres, testing of engineering materials and protection systems in salt and wet chamber, testing of protection coating characteristics, determining thickness, adhesiveness and other properties of all protection types, corrosion stability testing of engineering materials and welded joints (testing of riddled corrosion resistance, testing of intercrystalline corrosion resistance, testing of stress corrosion resistance, etc.), design and control of corrosion protection by coatings. Laboratory for Welding, with the equipment for basic electric arc welding processes and similar procedures (flame cutting and plasma cutting, soldering and thermal spraying), is used for scientific-research projects and cooperation with various companies. The Laboratory equipment: semiautomatic apparatus for MAG/MIG and TIG electric arc welding by impulse current TPS 2700, AC/DC apparatus for REL and TIG welding by impulse current MagicWave 2000, DC apparatus for REL and TIG welding by impulse TT 1600, DC MAG/MIG conventional welding apparatus, AC/DC conventional REL and TIG welding apparatus, on-line monitoring system for measuring, recording and processing main parameters of electric arc welding processes, apparatus for spot electric resistance welding, automatic tracking 89 ANNUAL REPORT 2010 Device for electric arc stud welding vehicle FTV 4 with remote control unit FCU-4-RC, apparatus for air plasma cutting Hypertherm Powermax 1250, Castolin Rotec 80 – apparatus for thermal spraying and cold spraying, implant apparatus for steel weldability testing, equipment for stud arc welding and 6 axis industrial robot for MAG/MIG welding with robotic welding positioner, and device for electric arc stud welding, etc. Laboratory for Metal Forming, Tools and Devices (with 20 m2 floor area) is used for testing of plastic flow stress, for determination of material behaviour during forming, for measuring deformation of metal samples, and for designing different tools (e.g. for punching, bending, deep drawing and forging), cutting tools and devices. The Laboratory equipment includes: off-centre 50-ton press, gravitational hammer, tensile tester, different tools for punching, bending, deep drawing, forging, etc. There are also software packages: MSC MARC, ANSYS, AutoCAD, Autodesk Inventor, for simulation of metal forming, used for scientific-research projects, as well as for cooperation with various companies. The simulations are used for calculation of metal forming parameters, for designing and optimization of metal forming tools. Bending of materials Various tools and test sample used for determination of plastic flow curve 90 ANNUAL REPORT 2010 Department for Materials Engineering Scientific-research activity of the Department for Materials Engineering includes: testing of metal and non-metal materials (as a part of education activities, work on projects and intensive cooperation with the economy). The Department is currently preparing documents needed for accreditation of the Laboratory for Materials Testing with Destruction at HAA (Croatian Accreditation Agency). The equipment used in the Laboratory is regularly calibrated according to EN ISO 17025. This provides the validity of results, as well as their comparison with the results acquired in other institutions during scientific research. As the result of scientific-research work, many papers were published in scientific journals, and in proceeding books (at international conferences). The Laboratory for Materials Testing with Destruction is part of the Department for Materials Engineering. The Laboratory is used for education purposes, scientific-research work and cooperation with the economy. The main Laboratory consists of the following Laboratories, i.e. sections: 1. 2. 3. 4. 5. Tensile tester Amsler, 400 kN Laboratory for Mechanical Testing Laboratory for Metallographic Testing Laboratory for Chemical Testing Laboratory for Heat Treatment and Thermal Measurement Laboratory for Tribology There is the following equipment in the Laboratory for Mechanical Testing: equipment for static testing of mechanical properties of materials at room temperature and high temperature, for toughness testing at room temperature and low temperature, hardness tester (for macro, semi-micro and micro hardness). Tensile tester 'Amsler' is used for testing of materials (by rupturing and bending) and test samples with max. loading 400 kN. Micro tensile tester 'FY-15' is used for testing paper, textiles and polymers with max. load 500 N, and tensile tester 'ZMGi' is for testing rubber, leather and polymers, max. load 2500 N. Charpy toughness tester is used for testing at room and lower temperature. Hardness tester 'Electronic Brinell', type HBE is used for testing macro-hardness (Brinell) with max. load 3000 N. Hardness tester 'Eseway' is used for testing macro-hardness (Vickers method, HV with load 30 – 2500 N, and Rockwell method, HRC with load 1500 N). Portable hardness tester 'MIC 10' with measuring probe 98 N, used for hardness testing on the building sites. Microhardness tester Durimet 'Leitz' is used for micro-hardness testing by Vickers method (HV) with load 0,15-20 N. Tensile tester 'Amsler', hardness testers and Charpy tester are calibrated and can be used not only in the education process but also in cooperation with the economy. Tensile tester FY 15, 500 N 91 ANNUAL REPORT 2010 There is the following equipment in the Laboratory for Metallographic Testing: metallographic light microscope 'Leica' DM 2500M (max. magnification 1000×), and electronic dilatometer 'Netzsch' 402 EP which is used for thermal analysis of material properties (temperature 25-1200 °C). Preparation of samples and their etching with reagents is performed in a separate space with removal of aggressive vapours through the digester. There is also the grinding and polishing machine used for the preparation of metallographic samples, as well as the metal cutting machine used for cutting of the hardest samples with water cooling. The probes are etched (with reagent) after preparation, and the testing is done on steels (at any stage of heat treatment, after welding, etc.), as well as on all other materials. The Laboratory for Chemical Testing is equipped with the spectrometer 'Belec' used for analysing the chemical composition of carbon and stainless steels. This apparatus is portable so that it can also be used outside the laboratory, i.e. on the work site. The layer analysis of the composition can be done using the adequate approach to preparation. Instrument calibration is done before each measuring. The Laboratory for Heat Treatment and Thermal Measurement is equipped with 'Cer' furnace with two chambers. The lower chamber (max. temperature 1100 °C) is used for hardening, tempering and annealing. The upper chamber (max. temperature 1400 °C) is used for heat treatment of steels. The lower chamber dimensions: ~300×300×600 mm, the upper chamber dimensions: ~150×300×600 mm. Laboratory furnace 'LHT' (max. temperature 1100 °C, chamber dimensions ~150×100×300 mm) is used for heat treatment of smaller samples. The multi-channel printer 'Honeywell' (up to 1500 °C, up to 1100 °C and up to 700 °C) and the control printers 'Almemo' 3290-8, D-83602 and 2090-8 are used for the control of furnaces (in the laboratory, as well as in the firms). There are also thermopairs PtRh-Pt and NiCr-Ni. Tensile tester ZMGi, 2500 N There are two test devices in the Laboratory for Tribology: 'SMT 1-2070' used for testing of friction and wear, with and without lubrication, and with max. speed of samples up to 1500 min-1 and loading up to 2000 N. There is also 'Taber Abraser' used for wear testing of metal and non-metal materials with loading 250-1000 g. These test devices are used for friction testing of the surface layers, as well as for comparing different layers (layers that are the result of heat/chemical treatment, welding, spraying, etc.) by monitoring dimension changes and/or mass loss. Two scales (precision: 10-2 g and 10-4 g) are used for the control of mass loss. Charpy toughness tester 92 ANNUAL REPORT 2010 DURIMET Leitz Brinell HBE ESEWAY Hardness tester MIC 10 Grinding and polishing machine Digester Dilatometer Metal cutting machine Spectrometer (for analysis of chemical composition) 93 ANNUAL REPORT 2010 Two-chamber furnace CER 94 Laboratory furnace LHT Tribology test device SMT 1-2070 Test device Taber-Abraser Microscope Leica DM 2500 Scales (precision: 0,01 g) Scales (precision: 0,0001 g) Microscope Zeis-Jena Neophot 21 ANNUAL REPORT 2010 Department for Industrial Engineering Laboratory for ERP systems and TCR The research work of the Department for Industrial Engineering includes: application of new maintenance strategies and methods of artificial intelligence, optimisation of tribo-mechanic systems using procedures of surface engineering, design and modelling of technology processes, implementation of CAD/CAPP/CAM technologies, development and application of models of process planning, testing and application of new production strategies and philosophies, application of artificial intelligence in process planning and control, application of quantitative engineering methods, experimental research and experiment analysis, modelling and development of IT systems of production companies, data exchange between CAD systems and IT systems of production companies, monitoring and control of processes. Scientific-research work of the Department and cooperation with the economy are the basis for the education process. As the result of scientific-research work, many papers were published in scientific journals, and in proceeding books (at international conferences). Scientific research of this Department is the basis for 5 graduate papers and 4 PhD dissertations. The following laboratories (of the Department) are used for education purposes, scientific-research work and cooperation with the economy: Siemens SIMATIC S7-314-2DP 1. Laboratory for ERP systems and TCR (Tele-Conference Room) 2. Laboratory for System Modelling and Process Control 3. Laboratory for Computer Aided Process Planning (CAPP) and ComputerAided Design (CAD) 4. Laboratory for Computer Integrated Manufacturing (CIM) and Maintenance 5. Laboratory for Rapid Prototyping Laboratory for ERP systems and TCR is used for development of ERP (Enterprise Resource Planning) system, for upgrading certain modules through implementation of mathematical models and models based on artificial intelligence defined during researches in the production companies. Interactive video conferences are used for cooperation with other institutions. Tele-Conference Room (TCR) is used for: - Lukas Nülle PLC and system for level control - Lectures - video conferences, where a large group of people can watch a lecture (held at some other location). This includes lectures for mandatory courses, as well as scientific conferences; short meetings such as: seminars, conferences, round table talks, presentations, etc. meetings that are of considerable interest for the academic community (e.g. educational or scientific purposes). 95 ANNUAL REPORT 2010 TCR can be used for holding lectures, video conferences, and other activities when the lecturer or the audience (students, teachers, researchers, etc.) are dislocated, i.e. not present. The lectures can be done in a completely interactive way, with participation of the audience, the possibility of asking questions in both directions, as well as interrupting the lecturer, so that everybody can participate. The Laboratory for System Modelling and Process Control is used for modelling, design, implementation of conventional and modern systems of control and visualisation of processes. Part of the equipment is shown in figures. Laboratory for CAPP and CAD The Laboratory equipment: - Industrial PLC (Programmable Logic Controllers): Siemens SIMATIC S7-314-2DP with DP unit IM-153 Computer for programming Siemens SIMATIC equipment, HMI (Human-Machine Interface) equipment and SCADA (Supervisory ControlAnd DataAcquisition) system Training equipment for pneumatics FESTO DIDACTIC with two assembly lines and FESTO PLC Computers for designing and controlling of FESTO equipment Programme support for Siemens SIMATIC equipment (STEP 7 Professional) Programme support for HMI and SCADA systems (WinCCFlexAdvanced). PC Mill 105 milling machine The programming of PLC is done with computer programmes (STEP 7 Professional, IEC 1131-3 of compatible development environment), the tests performed on a simulator and the programmes on the real PLC. Modular SIMATIC PLC concept enables testing of configuration combinations by using distributed periphery and different modules (digital inputs, digital outputs, analog inputs, analog outputs). The students also get to see various measuring probes and their application in combination with PLC. Various possibilities of PLC are shown in this way, which is the basis for creating the control infrastructure on more levels. The students get to programme PLC for solving various technologycontrol tasks. There is also programme support for process visualization – OP (Operational Panel) and PC based SCADA systems (WinCCFlex Advanced). In this way, it is possible to use COMPACT 5 CNC lathe Festo Didactic 96 ANNUAL REPORT 2010 PLC with textual/graphic control in a variety of combinations that occur in everyday life. There is also the programme support for advanced mathematic modelling and optimization MATLAB which enables studying of basic methods and optimization of structures and processes. The Laboratory for Computer Aided Process Planning (CAPP) and Computer Aided Design (CAD) deals with modelling in the field of technology and operative process planning. The Laboratory for Computer Integrated Manufacturing (CIM) and Maintenance deals with maintenance systems, i.e. application of new maintenance strategies (CBM, RCM, TPM, BCM) in order to prolong the work life of the equipment and plants, and to reduce maintenance costs. A special emphasis is put on the implementation of CAD/CAPP/CAM technologies. Part of the equipment is shown in figures. SCORBOT robot system The Laboratory equipment: portable instrument for measuring and gathering data from the equipment (DI 1100 and Vibscanner), laboratory instrument for vibration measuring. There is also the computer and programme support for maintenance control (information system for maintenance control – Infor EAM MP2; MIMIC 2001; OMNITREND), programme support for research and application of artificial intelligence (NeuralWorks Professional II/Plus, XpertRule Miner and XpertRule Knowledge Builder). The Laboratory for Rapid Prototyping is used for making prototypes in order to shorten the process of design, development and making of the prototype of the new product. Rapid Prototyping (RP) is a production procedure of the first model (of product) that can be used for testing different aspects of its shape and usability. RP procedures shorten the period of time necessary for making the first model of product: while time period for complex products (e.g. cars) was measured in days, months and years, it is reduced to hours and minutes. The most effective RP procedure is 3D Printing. The models in the Laboratory are made on a 3D Printer which is used for rapid prototyping. It is Z310 Printer from Z-Corporation (www.zcorp.com). This was the first device of that kind in Croatia, and this region, according to Mr CarlosAlvarez from the Swiss company MSM TradingAG. Measuring of vibrations (with portable measuring instruments) 97 ANNUAL REPORT 2010 This procedure is used for rapid production of prototypes, but also of finished parts and tools directly from CAD models. The flexibility of 3D printing cannot be compared to other procedures of rapid prototyping. Geometrically most complex parts can be made from almost any material (ceramics, metals, polymers, composites). Such models are used today in many fields. For example: in medicine (for making implants and prostheses), in pharmacology (for drugs with controlled effect), in architecture (for scale models of buildings), in mechanical engineering (for scale models of complex parts and moulds), in chemical industry (for making porous ceramic filters), etc. Due to all these possibilities, this laboratory is of great interest for the students, but also for other parties (e.g. from the economy). Different models made in the Laboratory are shown in figures. Different models made in the Laboratory Different models made in the Laboratory 98 Z310 3D Printer from Z-Corporation ANNUAL REPORT 2010 International Collaboration International Projects Integrity Assessment and Energy Efficiency of Structures in Service Report (first year of the project) Visit to Faculty of Mechanical Engineering, University of Belgrade, by the following researchers: - prof. dr. sc. Dražan Kozak and prof. dr. sc. Antun Stoić (12 April 2010) - prof. dr. sc. Dražan Kozak and prof.dr.sc. Lovre KrstulovićOpara (10 and 11 June 2010). The main researcher held a lecture entitled Fracture mechanics and integrity of welded structures (http://www.divk.org.rs). Students of Faculty of Mechanical Engineering (University of Kragujevac) could also follow this lecture via the internet link. This was a good opportunity to visit laboratories and Innovation Centre (head: prof. dr. sc. Aleksandar Sedmak) and to discuss future project activities. During the second visit, prof. Lovre Krstulović-Opara held a 3hour lecture on Infrared thermography with the following topics: Project coordinator: Professor Dražan Kozak E-mail: [email protected] Phone: +385 35 493 400 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 01.01.2010 - 31.12.2011 Program type: Croatian-Serbian bilateral cooperation project in the field of science and technology Project coordinator in Serbia: Prof. Aleksandar Sedmak, Faculty of Mechanical Engineering, University of Belgrade, Serbia Croatian participants in the project: Prof. Ivan Samardžić, Prof. Antun Stoić, Prof. Lovre Krstulović-Opara (FESB Split) Serbian participants in the project: Prof. Marko Rakin, Prof. Taško Maneski, Prof. Nataša Trišović 1) Introduction: wave length, IR thermography, Thermal Imaging Cameras (TIC), basics of thermodynamics and thermodynamic laws, black body radiation, etc. 2) Application of IR thermography: military, medicine, restoration of artworks, mechanical engineering, electrical engineering, etc. 3) Application of IR thermography in construction. 4) Energy efficiency (energy performance of buildings). As the result of this cooperation, the following papers were published: 1) Milošević-Mitić, Vesna; Kozak, Dražan; Maneski, Taško; Anđelić, Nina; Gaćeša, Branka; Stojkov, Marinko. Dynamic Nonlinear Temperature Field in a Ferromagnetic Plate Induced by High Frequency Electromagnetic Waves. Strojarstvo 52 (2010), 2; 115-124 2) Trišović, Nataša; Maneski, Taško; Kozak, Dražan. Developed procedure for dynamic reanalysis of structures. Strojarstvo 52 (2010), 2; 147-158 3) Hreha, Pavol; Hloch, Sergej; Magurova, Dagmar; Valiček, Jan; Kozak, Dražan; Harničarova, Marta; Rakin, Marko. Water Jet Technology Used in Medicine. Technical Gazette (Tehnički vjesnik) 17 (2010), 2; 237-240. 99 ANNUAL REPORT 2010 Furthermore, the following two papers will be published after review: 1) Vesna Milošević-Mitić, Branka Gaćeša, Dražan Kozak, Taško Maneski, Josip Sertić. Modeling of boiler membrane wall using finite element of reduced orthotropic plate. Strojarstvo. 2) Branka Gaćeša, Vesna Milošević-Mitić, Taško Maneski, Dražan Kozak, Josip Sertić. Numerical and Experimental Strength Analysis of Fire-Tube Boiler Construction. Technical Gazette. Researchers from Faculty of Mechanical Engineering (University of Belgrade) visited Mechanical Engineering Faculty in Slavonski Brod on 1 July 2010 and discussed future collaboration. The project collaborators during lunch in Belgrade (12.4.2010) In the time period from 12 April 2010 to 12 May 2010, Josip Sertić, dipl. ing. stroj. (mentor: prof. D. Kozak) – assistant at Mechanical Engineering Faculty in Slavonski Brod – stayed at Faculty of Mechanical Engineering in Belgrade, at Chair for Strenght of Materials (head: prof. T. Maneski, associate at this project). During this study visit, Sertić focused on the following: possibilities of numerical simulations and experimental investigations, master and PhD theses dealing with development of mathematical model for calculation of load at membrane walls of water-tube boilers, use of IR thermography (for measuring of stress at boiler membrane walls), etc. Prof. T. Maneski will be member of the Board for defence of PhD thesis of Josip Sertić. Due to cooperation on this project, the main researcher (from Croatia), prof. Dražan Kozak is associate at the national project which is coordinated by prof. T. Maneski. Furthermore, prof. Dražan Kozak is also a member of International Editorial Board of the journal: Structural Integrity and Life (http://www.divk.org.rs/ivk/ivked.html). The bilateral cooperation between Mechanical Engineering Faculty in Slavonski Brod and Faculty of Mechanical Engineering in Belgrade is extended with joint preparation of FP7 project (Call FP7-SSH-2011-1), entitled: Assessment of High-Level Education Knowledge (ASEDUC), which is being prepared according to the call for Collaborative project, Large-scale integrating projects (CP-IP). The first meeting of researchers was held on 30 July 2010. 100 From left to the right: Prof. dr. sc. Nataša Trišović, Prof. dr. sc. Dražan Kozak and Prof. dr. sc. Vesna Milošević-Mitić in Belgrade (12.4.2010) ANNUAL REPORT 2010 Ecologycal Justification of Application of Advanced Cutting Processes Project Description: Project coordinator: Professor Antun Stoić E-mail: [email protected] Phone: +385 35 446 188 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: 1.1.2010 - 31.12.2011 Programme type: Bilateral Croatian - Slovenian project Project coordinator for SLO: University of Ljubljana, Faculty of Mechanical Engineering Prof. dr. sc. Janez Kopač E-mail: [email protected] Members of Croatian team participating in the project: Prof. dr. sc. Ivan Samardžić, Prof. dr. sc. Dražan Kozak, BSc Miroslav Duspara Slovenian researchers participating in the project: Doc. dr. sc. Peter Krajnik, Mag. Davorin Kramar, Doc. dr. sc. Franci Pušavec Processing technologies on machine tools, particularly technologies of machining and deformation, are the largest consumers of industrial oils and lubricants and coolants for flushing and lubrication (SHIP). Industrial consumption is at the level of 35 % of the total consumption of oils and lubricants, of which about 50 % leaks by combustion, evaporation, spillage, residue in tanks or containers. The remaining 50 % can be collected and used as a secondary raw material. Numerous types of waste oils and lubricants, especially those using polychlorobiphenyl (PCBs), heavy metals and carcinogenic polycyclic aromatic hydrocarbons (PAHs) belong to the dangerous substances, and their collection and recycling should be made with care. It should be noted that the costs associated with the coolants used in machining processes in the last 20 years increased by 5 times and that was several times higher than the cost of cutting tools. The aim of this project is to determine the advantages of modern cooling techniques, which use less environmentally harmful waste SHIP (e.g. liquid nitrogen, MQL system, oil mist, dry treatment) and better monitoring systems in the SHIP process to reduce losses. Therefore, research on this project is oriented to objectively and scientifically based methods in order to examine and compare the differences of processing technology of classical and modern processing techniques. The project envisaged the research into the economic, environmental and technological aspects of the application of modern technology machining. Furthermore, since high speed machining processes with integrated cooling system which consumes a small amount of coolant (SHIP is harmful for humans and the environment) offer the possibility to reduce quantity of coolants, it could be expected that these technological solutions will provide savings in production and reduce internal production reserves. Activities of Croatian researchers during their stay in Slovenia: - preparation of papers for publication in journals (TV, SV, JAMME) and Conferences (TEAM,AMME, ICIT, CIM) - signed agreement (one-month visit for assistant Miroslav Duspara at Faculty of Mechanical Engineering in Ljubljana) - membership in Programme Committee. Activities of Slovenian researchers during their stay in Croatia: - lecture at postgraduate study - by Professor Janez Kopač - participation in the application of a new project network CEEPUS 2011/12 (coordinator prof. Aleksandar Makedonski) - preparation of papers for publication in journals (TV, SV, JAMME) and Conferences (TEAM,AMME, ICIT, CIM) - reviewing the university publications. 101 ANNUAL REPORT 2010 Applications of Rapid Manufacturing in Biomedical Fields Project Objective: Rapid Manufacturing methods show a great potential in the field of medical applications. They are at their essence most suitable for individual – custom made parts that are (almost 100 %) needed for medical applications. For example, hip implants are nowadays made in series of several modules – sizes. The choice is then made by the surgeon according to the patient's size. Even without making any mistakes, there is still a great chance that the chosen implant will not fit as supposed. The consequences are uneven and therefore rapid wear of an acetabular cup which leads to unplanned revision operations. Data show that 11 % of all unplanned revision operations for hip implant replacements are caused by the misalignment of the implant at the first installation. Using the Reverse Engineering and Rapid Manufacturing techniques, a vast majority of these problems can be avoided. Although a lot of research work has already been done in this field, the methods of surgical operations' planning and using the custom made implants have not been widely adopted by the medical staff. Reasons for that are very diverse but the most common one is a lack of understanding on both sides, i.e. medical as well as engineering side. The proposed network is aimed to overcome these obstacles by joining a small group of medical and engineering institutions to develop a common knowledge base that will enable mutual understanding of ever changing research subjects. The research and educational work will mostly be aimed at the following research/educational topics: ? Processing of the medical images (from CT and MRI). ? Printing Rapid Prototyping (RP) master models for medical applications (planning fitting, training, education). ? Designing and dynamically and statically analyzing medical implants. ? Production of bio-compatible implants (casting and direct manufacturing). ? Developing new bio-compatible materials (suitable for RP technologies). ? Case studies of using the RP parts for medical purposes. ? Analyzing the costs / benefits of using the RP for medical applications. ? Disseminating the knowledge and results, etc... Student and teacher mobility will offer good possibilities for knowledge exchange and development of new teaching strategies that will address the multidisciplinary aspect of the network's topics – cooperation between medical doctors and engineers. Moreover, during the mobility people will learn and benefit from new customs in foreign countries and institutes, develop new friendships and consequently improve their habits, working principles and knowledge. 102 Project coordinator: Professor Pero Raos E-mail: [email protected] Phone: +385 35 493 414 Funding scheme: CEEPUS II Academic year: 2010/2011 Program type: CEEPUS II project No CII-SI-0206-04-1011 Network coordinator: University of Maribor, Faculty of Mechanical Engineering, Institute for Production Engineering, Professor Igor Drstvenšek ANNUAL REPORT 2010 Students (under- and post-graduate) will benefit by having a chance to use the large "equipment base" of different laboratories of participating universities which will enable them to prepare better their final theses. New contents for interdisciplinary subjects to be taught at the participating institutions will be developed and evaluated during the workshop which will be held between September 15th and 20th in Maribor. The topics will include: ? Rapid Manufacturing – medical applications, ? Quality in medical equipment production, ? Ethics in medicine and engineering, ? Reverse engineering of body parts – CT and MRI data conversion and reconstruction of 3D parts, image processing and medical devices, ? Design and design optimization for rapid prototyping, ? Dynamic model construction and simulation for the sizing of implants, ? Implantation process – surgeon's view. Network partners: ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? Technical University of Cluj Napoca, Department of Manufacturing Engineering "Iuliu Hatieganu" University of medicine and pharmacy of Cluj Napoca, Department of Cranio-Maxillofacial Surgery University of Applied Sciences Vienna, Degree of Programme Mechatronics/Robotics University of Maribor, Faculty of Medicine University of Miskolc, Faculty of Mechanical Engineering, Department of Production Engineering University of Debrecen, Department of Mechanical Engineering Transilvania University of Brasov, Faculty of Medicine University of Novi Sad, Faculty of Technical Sciences University of Novi Sad, Faculty of Medicine University in Prishtina with temporary seat in Kosovska Mitrovica, Medical Faculty Slovak University of Technology in Bratislava, Faculty of Materials Science and Technology Technical University in Košice, Faculty of Mechanical Engineering, Department of Instrumental and Biomedical Engineering University of Monte Negro, Faculty of Mechanical Engineering Technical University of Koszalin, Faculty of Mechanical Engineering University of Nis, Faculty of Electronic Engineering University Sts. Cyril and Methodius Skopje, Faculty of Mechanical Engineering University of Rijeka, School of Medicine University Sts. Cyril and Methodius Skopje, Faculty of Medicine University of Sarajevo, Faculty of Mechanical Engineering, Department of Mechanical Production Engineering University of Zagreb, Faculty of Mechanical Engineering and Naval Architecture J. J. Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod, Department of Production Technologies. 103 ANNUAL REPORT 2010 INTelligent Automation for Competitive Advantage INTACA network is focused on the research topics of Intelligent Enterprise and Production Management, offering the possibility to intensify contacts between the CEEPUS Partner countries. The main goal of the network is to prepare students to conduct theoretical and applied research in advanced manufacturing and to encourage inter-disciplinary studies. Realized incoming mobility to our Faculty in the year 2010: Prof. Borut Buchmeister, University of Maribor, Faculty of Mechanical Engineering, Slovenia. - Partner institutions in the INTACA network: University of Novi Sad, Serbia University ofApplied Sciences Vienna,Austria Graz University of Technology,Austria University of Zenica, Bosnia and Herzegovina J. J. Strossmayer University of Osijek, Croatia Budapest University of Technology and Economics, Hungary University Sts. Cyril and Methodius – Skopje, Macedonia Cracow University of Technology, Poland University of Kragujevac, Serbia University of Maribor, Slovenia and Technical University in Košice, Slovak Republic. Visit of the delegation from Novi Sad to our Faculty 104 Project coordinator: Professor Dražan Kozak E-mail: [email protected] Phone: +385 35 493 400 Funding scheme: CEEPUS II Project duration: since acad. year 2007/2008 Program type: CEEPUS II project No CII-RS-0065-05-1011 Network coordinator: mr. sc. Bojan Lalić, Faculty of Technical Sciences, University of Novi Sad, Serbia ANNUAL REPORT 2010 Implementation and Utilization of e-Learning Systems in Study Area of Production Engineering in Central European Region Project Objective: The main objective for all participating partners in the proposed projects is implementation and utilization of e-learning systems in the study area of production engineering in Central European Region. The main objective is in concordance with the e-learning initiative of the European Commission. ? Project coordinator: Professor Dražan Kozak E-mail: [email protected] Phone: +385 35 493 400 ? Funding scheme: CEEPUS II Project duration: since acad. year 2007/2008 ? ? Program type: CEEPUS II project No CII-RO-0202-04-1011 Network coordinator: Prof. Nicolae Ungureanu, Faculty of Engineering, North University of Baia Mare, Romania ? ? Realized incoming mobility to our Faculty in the year 2010: Prof. Nicolae Ungureanu, North University of Baia Mare, Faculty of Engineering, Romania Prof. Radu Cotetiu, North University of Baia Mare, Faculty of Engineering, Romania Doc.dr. Igor Budak, University of Novi Sad, Faculty of Technical Sciences, Serbia Prof. Gábor Páy, College Nyíregyháza, Hungary Prof. Sergej Hloch, Technical University of Košice, Faculty of Manufacturing Technologies in Prešov, Slovak Republic Ing. Ludmila Novakova-Marcinčinova, Technical University of Košice, Faculty of Manufacturing Technologies in Prešov, Slovak Republic. Realized outgoing mobility in the year 2010 to the following universities: ? Prof. Dražan Kozak, North University of Baia Mare, Faculty of Engineering, Romania ? Prof. Antun Stoić, North University of Baia Mare, Faculty of Engineering, Romania ? Prof. Željko Ivandić, Jan Evangelista Purkyne University in Ústí nad Labem, Czech Republic ? Prof. Dražan Kozak, Poznan University of Technology, Poland ? Prof.Antun Stoić, Poznan University of Technology, Poland. Prof. Cotetiu and Prof. Ungureanu together with our Vice-Dean for Science Prof. Živić at the Mechanical Engineering Faculty in Slavonski Brod At the entrance to JEP University in Ústí nad Labem 105 ANNUAL REPORT 2010 Development of Mechanical Engineering (Design, Technology and Production Management) as an Essential Base for Progress in the Area of Small and Medium Companies' Logistics - Research, Preparation and Implementation of Joint Programs of Study Our mobility strategy is to create the possibilities of reciprocal exchange of information, knowledge, to develop joint programs, participation in the common research activities, assistance with work on PhD and graduate theses, laboratory work in the pedagogical field, lectures, seminars, summer schools, and also participation at the scientific conferences and workshops organized by network partners. We encourage exchange of experience between university teachers in the area of mechanical and production engineering, implementation of advanced methods, aspects and modern IT in education. Seminars and consultations for PhD students with academic staff of hosting universities and their excursions to the companies in region of partners will be organised. Some books and lectures will be prepared and published in English for joint programs. ? ? Realized incoming mobility to our Faculty in the year 2010: Prof. Jozef Novak-Marcinčin, Technical University of Košice, Faculty of Manufacturing Technologies in Prešov, Slovak Republic Prof. Csaba Gyenge, TU of Cluj-Napoca, Romania. Realized outgoing mobility in the year 2010 to the following universities: ? Prof. Ivan Samardžić, Poznan University of Technology, Poland ? Prof. Željko Ivandić, TU Sofia, Bulgaria ? Prof. Ivan Samardžić, TU Sofia, Bulgaria ? Miroslav Duspara, PhD student, TU Sofia, Bulgaria ? Mato Kokanović, PhD student, TU Sofia, Bulgaria ? Željko Rosandić, PhD student, Tomas Bata University in Zlin, Czech Republic. Project coordinator: Professor Dražan Kozak E-mail: [email protected] Phone: +385 35 493 400 Funding scheme: CEEPUS II Project duration: since acad. year 2004/2005 Program type: CEEPUS II project No CII-PL-0033-06-1011 Network coordinator: Prof. Stanislav Legutko, Poznan University of Technology, Poland Visit of our delegation to TU Poznan, together with Prof. Legutko Prof. Ivan Samardžić - holding a lecture (Manufacturing 2010 Conference in Poznan) 106 ANNUAL REPORT 2010 Unconventional and Hybrid Unconventional Processes and Production Technologies Network Project Objective: Project coordinator for MEFSB: Professor Antun Stoić E-mail: [email protected] Phone: +385 35 446 188 Funding scheme: Ministry of Science, Education and Sports of Republic of Croatia Project duration: since acad. year 2007/2008 Program type: CEEPUS II project No CII-BG-0203-02-0910 Coordinated by: Dr. Sc. Eng. Aleksandar Makedonski Ivanov, TU-Sofia Faculty of Machine Technology Status of MEFSB: Participating unit Unconventional machining and surface processes are specialized operations used by industrial companies worldwide. They are particularly applicable for the shaping and finishing of materials that are difficult to process by conventional methods of machining and are often regarded as complementary technologies to existing practices. The main objectives of Project-network are: ? To establish a network between universities (cooperation between Departments and Institutions, as well as people) with similar study program in the field of Unconventional Processes and Production Technologies and to associate the effort in developing joint research projects for international grants in the near future; ? To promote the regional cooperation in education and accelerate information transfer in the field of common interest; ? To increase the possibility for utilization of unique laboratory equipment and devices in the participating universities for research work, mainly for young teachers working on their dissertations and for PhD students, as well as for students working on their master thesis; ? To investigate environmental protection in unconventional production technologies with a special emphasis on the development of constructional solutions aiming to decrease their harmful influence; ? To prepare highly-skilled engineers that will contribute to acquisition of commercial leadership of the European companies in the nonconventional technologies. Mobility in 2009/10: 1) Incoming: short term students 3 /3 months; teacher 3/3 months 2) Outgoing: short term students 3 /3 months; teacher 3/3 months Important event for network was common partner meeting in 2010 at Conference AMO 2010 and publishing of AMO Journal. Network was active up to October 2010, and was reactivated and funding again in 2011. Participating units: 1) Technical University of Sofia, Faculty of Machine Technology, Department of Manufacturing Technology 2) VŠB – Technical University of Ostrava, Department of Machining andAssembly 3) Czech Technical University in Prague, Faculty of Mechanical Engineering 4) J. J. Strossmayer University of Osijek, Mechanical Engineering Faculty in Slavonski Brod 5) University of Miskolc, Department of Materials Handling and Logistics 107 ANNUAL REPORT 2010 6) University Sts. Cyril and Methodius – Skopje, Faculty of Mechanical Engineering - Skopje, Institute of Production Engineering 7) Koszalin University of Technology, Faculty of Mechanical Engineering 8) Poznan University of Technology, Institute of Mechanical Technology 9) Cracow University of Technology, Faculty of Mechanical Engineering 10) Technical University of Cluj-Napoca, Faculty of Machine Building, German Department 11) "Iuliu Hatieganu" University of Medicine And Pharmacy of Cluj Napoca, Department of Environmental Health 12) University of Nis, Faculty of Mechanical Engineering 13) Technical University in Zvolen, Department of Woodworking Machines and Equipment, Faculty of Environmental and Manufacturing Technology 14) Slovak University of Technology in Bratislava, Faculty of Mechanical Engineering, Department of Manufacturing Systems. 108 ANNUAL REPORT 2010 Visits to the MEFSB within the CEEPUS Funding Scheme From 12 to 15 May 2010, prof. Aleksandar Makedonski Ivanov and prof. Georgi Popov (Faculty of Machine Technology, Department of Manufacturing Technology, TU Sofia) visited Mechanical Engineering Faculty in Slavonski Brod as a part of CEEPUS II project "Unconventional and hybrid unconventional processes and production technologies" (project coordinator: prof. Antun Stoić). Their hosts were Vice-Dean for Science prof. Marija Živić and Technical Editor of Technical Gazette prof. Milan Kljajin. This was the perfect opportunity to visit laboratories at Mechanical Engineering Faculty, as well as University ofApplied Sciences of Slavonski Brod. On 16 June 2010, prof. dr. Leon Kukielka from Technical University of Koszalin, Mechanical Engineering Faculty (Poland) held a lecture at Mechanical Engineering Faculty in Slavonski Brod entitled: "Numerical Modelling and Simulation of the Movable Contact Tool-Workpiece and Application in Technological Processes", as part of the CEEPUS project: "Implementation and utilization of e-learning systems in study area of production engineering in Central European Region". 109 ANNUAL REPORT 2010 On 15 July 2010, prof. dr. sc. Sergej Hloch from Faculty of Manufacturing Technologies, TU Košice with a seat in Prešov (Slovak Republic) and prof. dr. sc. Jan Valíček from Institute of Physics, Mining and Geology Faculty, VSB TU Ostrava (Czech Republic) held a lecture entitled "Current State of Abrasive Water Jet Technology in Theory, Science and Practice" at Mechanical Engineering Faculty in Slavonski Brod. The lecture was part of the CEEPUS II project. Prof. dr. sc. Jan Valíček, Prof. dr. sc. Željko Ivandić, Prof. dr. sc. Sergej Hloch and Prof. dr. sc. Dražan Kozak 110 Prof. dr. sc. Sergej Hloch ANNUAL REPORT 2010 Signed Agreements on International Collaboration Mechanical Engineering Faculty, University of Sarajevo Agreement on scientific, teaching and technical cooperation was th signed (26 March 2010) by the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak, and the Dean of the Mechanical Engineering Faculty, University of Sarajevo prof. dr. sc. Ejub Džaferović. 111 ANNUAL REPORT 2010 Faculty of Engineering, North University of Baia Mare The cooperation agreement was signed (13th April 2010) by the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak, and the Dean of the Faculty of Engineering, North University of Baia Mare, Prof. Ph.D. MSc. Eng. Radu Cotetiu. 112 ANNUAL REPORT 2010 Faculty of Machine Building, Technical University of Cluj-Napoca The cooperation agreement was signed (12th May 2010) by the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak, and the Dean of the Faculty of Machine Building, Technical University of Cluj-Napoca, Prof. dr. Eng. Petr Berce. Prof. dr. Eng. Petr Berce and Prof. dr. sc. Dražan Kozak 113 ANNUAL REPORT 2010 Faculty of Environmental and Manufacturing Technology, Technical University in Zvolen The cooperation agreement was signed (16th June 2010) by the Dean of the Faculty of Environmental and Manufacturing Technology, Technical University in Zvolen, prof. dr. sc. Milan Mikleš and the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak. Faculty of Machine Technology, TU Sofia The cooperation agreement was signed (26th June 2010) by the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak, and the Dean of the Faculty of Machine Technology, TU Sofia, Bulgaria, Assoc. Prof. PhD. Georgi Todorov. The host was prof. dr. sc. Georgi Popov, Head of Department of "Mechanical Engineering and Machine Tools" (TMMM) at Technical University of Sofia. Prof. dr. sc. Georgi Todorov is a Head of CAD/CAM/CAE Virtual Laboratory, which is Centre of excellence established by the Bulgarian Ministry of Education, Youth and Science. Prof. dr. sc. Dražan Kozak and Prof. dr. sc. Georgi Todorov 114 From left to the right: Prof. Dražan Kozak, Prof. Georgi Todorov, Prof. Antun Stoić and Miroslav Duspara ANNUAL REPORT 2010 Faculty of Mechanical Engineering, University of Maribor The cooperation agreement was signed (6th July 2010) by the Dean of the Faculty of Mechanical Engineering, University of Maribor, prof. dr. Niko Samec and the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak. Faculty of Technical Sciences, University of Novi Sad The cooperation agreement was signed (1st October 2010) by the Dean of the Faculty of Technical Sciences, University of Novi Sad, prof. dr. Ilija Ćosić and the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak. The cooperation between our institutions was initiated and coordinated by Prof. Milan Kljajin. The Faculty of Technical Sciences in Novi Sad awarded the MEFSB with the plaque on the occasion of its 50 years of existence From left to the right: Prof. Janko Hodolič, Prof. Dražan Kozak, Prof. Ilija Ćosić and Prof. Milan Kljajin Prof. dr. sc. Dražan Kozak and Prof. dr. Ilija Ćosić 115 ANNUAL REPORT 2010 Tomas Bata University in Zlin The cooperation agreement was signed (16th September 2010) by the Vice-Rector Tomas Bata University in Zlin, Assoc. Prof. Vojtěch Křesálek, and the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak. Faculty of Production Technology and Management, the Jan Evangelista Purkyně University in Ústí nad Labem The cooperation agreement was signed (26th November 2010) by the Dean of the Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, prof. dr. sc. Dražan Kozak, and the Dean of the Faculty of Production Technology and Management, the Jan Evangelista Purkyně University in Ústí nad Labem, Prof. Dr. Ing. František Holešovský. In the Croatian team there were also prof. dr. sc. Ivan Samardžić, prof. dr. sc. Antun Stoić and prof. dr. sc. Željko Ivandić. Prof. Dr. Ing. František Holešovský and Prof. dr. sc. Dražan Kozak 116 ANNUAL REPORT 2010 International Students Exchange Mr. Amine Nsairia, student of National School of Engineering of Tunis (ENIT) and Prof. dr. sc. Dražan Kozak, the Dean of Mechanical Engineering Faculty in Slavonski Brod Mr. Amine Nsairia, has been a visiting scholar at the Mechanical Engineering Faculty in Slavonski Brod, University of Osijek, Croatia in the period of June 01 to July 16, 2010 through IAESTE exchange program. 117 ANNUAL REPORT 2010 Traineeship at TU Clausthal Ever since the beginning of my university education, I had a dream to visit and work at one of the international faculties. During the past few years, I had the opportunity to meet students who decided to do the practical training abroad. Nevertheless, none of their stories could have prepared me for all surprises and difficulties that I encountered there; unfamiliar place, new people and completely different way of life. My work and stay at Clausthal University of Technology was very specific and defined. All students and teachers I worked with were really friendly and helped me a lot during my traineeship. This study visit did not only help me to understand better the practical side of Mechanical Engineering, but it also helped me to develop more as a person. During this traineeship, I met many interesting people from all around the world and every single one of them had a specific part in this wonderful life experience. We all became good friends and created many happy memories together. I would warmly recommend this experience for all those who have a desire to explore the world. Sincerely yours, Karolina Kamenski 118 ANNUAL REPORT 2010 Erasmus Mobility Programme Higher education institutions which want to participate in Erasmus actions must have an Erasmus University Charter (EUC). The Charter aims to guarantee a high level of quality in mobility and cooperation by setting out fundamental principles for all Erasmus actions that participating institutes must follow. University of Osijek applied for EUC in 2009. There was no incoming mobility to Croatia for 2009/2010, and 2010/11, but it is planned for the academic year 2011/12. Mechanical Engineering Faculty in Slavonski Brod, i.e. University of Osijek, has signed Erasmus Bilateral Agreements with the following higher education institutions: 1. University of Maribor, Faculty of Mechanical Engineering, Maribor, Slovenia 2. University of Pecs, Pollack Mihaly Faculty of Engineering, Pecs, Hungary 3. Kecskemét College, Faculty of Mechanical Engineering and Automation, Kecskemet, Hungary. Mobility in the academic year 2009/2010: Erasmus Mobility Programme, established in 1987, is one of the sectoral programmes of the EU's Lifelong Learning Programmes (from 2007 to 2013). There are also other programmes: Comenius (for school education), Leonardo da Vinci programme (for vocational training), Grundtvig (for adult education), Transversal programme (for activities that include cooperation between different sectors, Jean Monnet programme (for European integration). The general aim of the Programme is student mobility, and staff mobility (teaching and other staff from higher education institutions). There is Erasmus student mobility for studies and Erasmus student mobility for placements (traineeship) which enable students at higher education institutions (undergraduate, graduate or postgraduate studies) to spend an integrated period of study in another participating country. Teaching staff mobility enables staff to spend a teaching period at a higher education institution in another participating country. There is also staff mobility for training which enables teaching and other staff of higher education institutions to acquire knowledge or practical skills relevant for their current job and their professional development. - - Prof. dr. sc. Dražan Kozak - at University of Maribor, Faculty of Mechanical Engineering, Maribor, Slovenia - held lectures at the postgraduate study (topic covered: Structural integrity assessment), from 13-15 December 2009. Izv. prof. dr. sc. Katica Šimunović - at University of Pecs, Pollack Mihaly Faculty of Engineering, Department of Mechanical Engineering, Pecs, Hungary - held lectures at the undergraduate study (topics covered: Thermal spraying, Flame spraying), from 12-14April 2010. Mobility in the academic year 2010/11: - - Prof. dr. sc. Pero Raos - at Kecskemét College, Faculty of Mechanical Engineering and Automation, Kecskemet, Hungary – held lectures at the undergraduate study (topic covered: Principles of polymer processing), from 04-05 November 2010. Josip Stojšić, dipl. ing., PhD student - at Kecskemét College, Faculty of Mechanical Engineering and Automation, Kecskemet, Hungary - student mobility for placements (activities: Rheological measurements on high pressure capillary rheometer; Modelling of injection moulding; Calculation of rheological data), from 18 October 2010 to 18 January 2011. 119 ANNUAL REPORT 2010 Other Events Power Plant Symposium for Students in Slavonski Brod Power Plant Symposium for Students in Slavonski Brod was held on 15 November 2010 at Mechanical Engineering Faculty in Slavonski Brod. The main goal of this Info Day was to show which possibilities are offered to MEFSB students by the company Bilfinger Berger Power Services (BBPS) from Germany. 120 ANNUAL REPORT 2010 121 ANNUAL REPORT 2010 122 ANNUAL REPORT 2010 English in Action at MEFSB: Business Communication Skills Over eighteen years, English in Action (EiA) have become the leading specialist in the area of in-school communicative English courses, working with schools in more than 20 countries worldwide. Each year, over 10,000 students participate in one of the programmes. Each programme is supported by a dedicated team of professionals, from academics to operational staff, based either at the Head Office in Canterbury England or in offices in the countries where they operate. Programmes are specifically designed to complement the formal, year-round classroom work undertaken by English language students in their own countries. EiAare unique in providing: ? a range of 1 and 2 week English Language courses for students ? individually designed programmes for delivery in your own school ? experienced, qualified, native English-speaking teachers flown direct from the UK ? the tools to build students' confidence and motivation ? an ideal complement to the learning undertaken in students' regular English classes ? a realistic alternative to more expensive overseas study tours Course participants: 1. mr. sc. Jasna Ažman 2. Tomislav Baškarić, univ. bacc. ing. mech. 3. Klara Bilić-Meštrić, prof. 4. Darko Damjanović, univ. bacc. ing. mech. 5. dr. sc. Mirko Karakašić 6. prof. dr. sc. Milan Kljajin 7. Mato Kokanović, dipl. ing. 8. prof. dr. sc. Dražan Kozak 9. mr. sc. Irena Krumes-Šimunović 10. prof. dr. sc. Roberto Lujić 11. mr. sc. Zlatko Pavić 12. prof. dr. sc. Pero Raos 13. Nada Rosandić, dipl. ing. 14. Željka Rosandić, prof. 15. Željko Rosandić, dipl. ing. 16. prof. dr. sc. Ivan Samardžić 17. Marija Somolanji, prof. 18. prof. dr. sc. Marinko Stojkov 19. Josip Stojšić, dipl. ing. 20. doc. dr. sc. Katica Šimunović 21. Slaven Vidmar, dipl. iur. 22. Željko Zmaić, dipl. ing. 23. prof. dr. sc. Marija Živić Using English clearly and effectively is becoming essential for future success. These short, communicative courses provide the ideal complement to students' regular classroom learning. Delivered in students' own schools, EiA courses are easy to organise, and are a cost effective and stress-free alternative to an overseas study visit. With a commitment to quality of service they offer a range of courses to meet the expectations of students in the new millennium. EiA Course at MEFSB Description of the course held at the Mechanical Engineering Faculty in Slavonski Brod: ? Course: Business Communication Skills ? CEF Level:A2/B1 ? Course date: 05-09 July 2010 ? Hours per Week: 25 ? EiAteachers: Jacqueline Miller and Jay Fonow ? Contact Teacher (MEFSB): Željka Rosandić 23 students / professors from the Mechanical Engineering Faculty (MEFSB) spent a week (05-09 July 2010) working with EiA teachers Jacqueline Miller and Jay Fonow on the popular Business Communication Skills programme. 123 ANNUAL REPORT 2010 Course Content Getting to Know You Company Business Roles & Responsibilities Telephoning Making an Appointment Presentations 1 Describing Products Checking Information Keeping the Customer Happy Product Design Presentations 2 In My Life At the Bank Holiday Getting Around Britain Holiday Design Presentations 3 Hotel Directions Restaurant Not Just London Presentations 4 Company Departments Jobs & Personalities In the Office Reading the Signs Presentations 5 Asking and responding to personal information questions Meeting and introducing people, discussing roles and company business Talking about job titles and duties, filling in forms Making and receiving telephone calls, taking notes and messages from phone calls Making appointments and arranging meetings Discussing and planning a presentation Selling products and discussing sales Requesting, providing, checking and confirming information Making and responding to complaints Designing, presenting and discussing a new product Deciding on presentation topics and organising a presentation Identifying and discussing dates, times, weights and measur ement Carrying out bank transactions Describing, designing and selling a holiday Requesting and providing travel information Making suggestions and providing opinions Planning and practicing a presentation Providing booking information and reserving a hotel room Describing places and requesting and giving directions Providing definitions and discussing traditional British dishes Discussing and presenting places of interest Assessing and providing feedback on presentations Identifying and discussing the roles of different departments within a company Describing different personality types and discussing their suitability for specific job roles Identifying, naming and describing office equipment Interpreting signs and symbols Delivering group presentations Our experience with EiA EiA provided a friendly and personal service, backed up by a team of dedicated professionals at their office in Canterbury. Every step of the way, they were always there to help. Provided by EiA: ? Academic support and guidance on course choices ? Afully structured English programme ? Qualified English teachers to deliver the course 124 ANNUAL REPORT 2010 ? ? ? ? ? ? ? ? ? ? ? All flights, accommodation, subsistence and travel for EiA teachers Specially designed course workbooks and support materials EiAfolders and pens for every participant An end-of-course attendance certificate at the appropriate level A designated Senior Teacher to liaise regularly with the school Contact Teacher during the course. Provided by MEFSB: A separate classroom for each EiA class, with moveable desks and chairs A blackboard or whiteboard in each classroom, plus marker pens or chalk, as appropriate Regular access to a photocopier Asuitable space for the end of course presentation/show A designated Contact Teacher to liaise regularly with EiA Senior Teacher over the course implementation CD players for audio materials. This was a wonderful and very successful week with English in Action. The students had a great chance to interact with very interesting native speakers, which has helped them improve their oral skills. Course topics and activities were relevant and meaningful. Moreover, small class sizes and a relaxed environment offered accelerated learning opportunities. Workbooks and support materials were tailor-made for our course. The motto of the course was: Communication, even where it displays some errors, is preferable to no communication. Contact: English in Action Ltd, Partnership House, 22 Hawks Lane, Canterbury, United Kingdom, www.englishinaction.com 125 ANNUAL REPORT 2010 Lectures held at MEFSB Lecture "Statistical methods and scientific-research work" was held on 16 November 2010 at Mechanical Engineering Faculty in Slavonski Brod by prof. dr. sc. Nikola Šakić (Faculty of Mechanical Engineering and Naval Architecture, Zagreb). This lecture was organised by Department for Production Engineering. Prof. dr. sc. Janez Kopač Lecture for PhD students was held on 10 December 2010 at Mechanical Engineering Faculty in Slavonski Brod by prof. dr. Janez Kopač (Faculty of Mechanical Engineering, University of Ljubljana). Prof. Kopač talked about titanium alloy processing (used for implants), high-pressure water cutting, etc. PhD students (module: Modern Production Processes) were offered the possibility of conducting an experiment in the laboratory at the Faculty of Mechanical Engineering, University of Ljubljana. Lecture "Modification and coating procedures with special emphasis on vanadium / aluminium modified steel" was held on 16 December 2010 by prof. dr. sc. Božidar Matijević (Faculty of Mechanical Engineering and Naval Architecture, Zagreb). This lecture was organised by Department for Materials Engineering. 126 ANNUAL REPORT 2010 Croatian Society of Mechanics, section Slavonski Brod Lectures in 2010 Lecture "Numerical methods in design and analysis of solid fuel fire-box" was held on 21 May 2010 at Mechanical Engineering Faculty in Slavonski Brod by prof. dr. sc. Ivan Pešenjanski (Faculty of Technical Sciences, Novi Sad). Prof. dr. sc. Ivan Pešenjanski Prof. dr. sc. Dražan Kozak, mr. sc. Biljana Miljković, prof. dr. sc. Marija Živić, prof. dr. sc. Ivan Pešenjanski and mr. sc. Borivoj Stepanov Prof. dr. sc. Jurij Avsec Lecture "Model of circulatory system with concentrated parameters" was held on 9 June 2010 at Mechanical Engineering Faculty in Slavonski Brod by prof. dr. sc. Zdravko Virag (Faculty of Mechanical Engineering and Naval Architecture, Zagreb) and Fabijan Lulić, dr.med., spec. cardiologist (Nemetova Polyclinic, Zagreb). Lecture "From macromechanics through micromechanics to nanomechanics" was held on 11 October 2010 at Mechanical Engineering Faculty in Slavonski Brod by prof. dr. sc. Jurij Avsec (Faculty of Energy Technology, University of Maribor). 127 ANNUAL REPORT 2010 Seminar on rapid prototyping, 3D printing and 3D scanning In November 2010, an open seminar on rapid prototyping, 3D printing and 3D scanning was organized in cooperation with the company CADD print Ltd. During the seminar, an overview of all available 3D printers on the market was presented, with special emphasis on process similarities and differences between 3D printers and other prototyping systems based on plastic materials. The key criteria for choosing the appropriate 3D printing system were analyzed along with the presented case studies from regional practices in the field of engineering, medicine and architecture. Furthermore, portable 3D scanning devices were reviewed as a supporting technology, closely related to rapid prototyping. The seminar was well attended by businessmen, faculty staff and students. 128 ANNUAL REPORT 2010 Festival of Science 2010 (19-24 April 2010) The eight Festival of Science was organized at all Croatian Universities from 19-24 April 2010. The main purpose of this manifestation is to bring science and scientific work closer to the general public (especially to primary and secondary schools) in order to make science more popular and appealing to the younger generations. This year, the Festival was dedicated to topics related to the planet Earth. Mechanical Engineering Faculty in Slavonski Brod participated with one poster entitled: A model of mechanized device for ecological tillage (authors: Ivan Hradovi – student; prof. dr. sc. Željko Ivandić – mentor). "The poster deals with the topic Earth, as well as with the ecology. It promotes a healthy life style and exercise because the device is propelled by human power, i.e. by pushing. At the same time, this innovative product could be used for starting student entrepreneurship." (taken from theAbstract). Mechanical Engineering Faculty participated for the first time in the Festival of Science in 2009. The topic was "Evolution". A workshop entitled Writing and drawing by hand – writing and drawing by computer was organised by mr. sc. Vjekoslav Galzina and Ilija Svalina, dipl. ing., and students Ivan Gelo, Hrvoje Čorić and graduate student Mario Galović. Primary school students had the opportunity to see how writing and drawing evolved through years from the early beginnings up to using computers. Students spent most of the time writing and drawing by computer and finally their signatures were printed on large-format printer. The workshop was well accepted and graded with 4,8 by the participants. Two variants from the poster entitled: A model of mechanized device for ecological tillage (authors: Ivan Hradovi – student; prof. dr. sc. Željko Ivandić – mentor) 129 ANNUAL REPORT 2010 Visit to the European Centre for Renewable Energy in Güssing (Austria) (24 September 2010) Agency for Export and Investment Promotion (AEIP) initiated foundation of the Centre of Excellence for renewable energy sources with specialization in biomass (in Slavonski Brod). AEIP signed a cooperation agreement with Town of Slavonski Brod and Brod-Posavina County (on 2 March 2010, in Zagreb). This Centre would offer various types of services: education, research and development of technologies, certification of products and equipment in the field of biomass. The main goal is to improve cooperation between scientific institutions and economy. The Centre would be located in the industrial zone Bjeliš. Therefore, AEIP organized a study visit to the European Centre for Renewable Energy in Güssing (Austria). Representatives of the following institutions were part of this visit: Development Agency Slavonski Brod, CTR Slavonski Brod, Brodin, Brod-Posavina County, Mechanical Engineering Faculty in Slavonski Brod (represented by prof. dr. sc. Marija Živić and prof. dr. sc. Marinko Stojkov), Ministry of Economy, Labour and Entrepreneurship, Agency for Export and Investment Promotion. The participants visited the region of Güssing in Austria to learn from the renewable energy developments which have crowned the region as a model of sustainable energy supply. The European Centre for Renewable Energy (Germ. abbr. EEE), headquartered in Güssing (southern Burgenland), was founded in 1996. The EEE develops lasting regional and community-based concepts for energy conservation and for the generation and use of renewable energy. As a reliable partner in various national and European networks, the EEE has gained an excellent reputation in the fields of research and development and project management. The EEE is also a co-founder of Eco Energy Land and acts as an umbrella organisation for all energy-related 130 Prof. Marija Živić and Prof. Marinko Stojkov (Mechanical Engineering Faculty in Slavonski Brod) visited the European Centre for Renewable Energy (German abbr. EEE) headquartered in Güssing (southern Burgenland). ANNUAL REPORT 2010 activities in the Güssing region. It organises lectures and training in the field of renewable energy and tours through Eco Energy Land. The Güssing model is considered a model for success and is now recognized internationally as an energy/biomass centre. Starting with wood as a raw material, goals such as regional development, job creation, as well as research and development are made sustainable through several initiatives, projects and the courage to act. The goals already achieved should be further developed in the future, and for this reason, they strive to expand the energy self-sufficiency of the city of Güssing into the entire region of Güssing. The positive aspect of this system and philosophy is that the Güssing model can be transplanted to any place in the world. With the construction of the biomass power plant, the goal of energy self-sufficiency also seems to have been achieved. In Güssing, more heat, fuel, and electrical energy has been produced from regional raw materials in the balance of the year than the city actually needs. Within 15 years, what was once one of the poorest regions in Austria has achieved a high standard of living and a better quality of life. Through cooperation with the regional schools, young people are already confronted with the topic of "the environment" and can then find well-paying jobs after they have completed school. During the study trip, partners visited a biomass power plant in Güssing, a district heating plant combined with solar in Urbersdorf, and a biogas plant in Strem. 131 ANNUAL REPORT 2010 132 ANNUAL REPORT 2010 Conference on Engineering Research Sixth International PhD & DLA Symposium University of Pécs Pollack Mihály Faculty of Engineering Pécs, Hungary, 25-26 October 2010 The Sixth International PhD & DLA Symposium was organized by University of Pécs, Pollack Mihály Faculty of Engineering, from 25-26 October 2010. The conference was organized for PhD & DLA students in the field of engineering and architecture, since they need a special forum in addition to their PhD & DLA programs to present the results of their ongoing research and to discuss the results of the ongoing PhD & DLA studies in order to support the future activities. There was the Exhibition of the Architectural Doctoral School and more than 100 papers were presented at the conference and published in the proceedings. Mechanical Engineering Faculty in Slavonski Brod was represented by dr. sc. Štefanija Klarić, Željko Rosandić, and dr. sc. Andrijana Milinović who presented the paper: Examination of welding parameters influence on Stud Arc Welding process. Dr. sc. Štefanija Klarić and dr. sc. Andrijana Milinović 133 ANNUAL REPORT 2010 Publications Published Books Milan KLJAJIN & Milan OPALIĆ INŽENJERSKA GRAFIKA 1st edition 2010, Size 24 × 17 cm, 472 pages, Paperback Publisher: Mechanical Engineering Faculty in Slavonski Brod ISBN 978-953-6048-56-4 Price: 180,00 kn Contents: Predgovor; Grafička komunikacija u tehnici; Normizacija; Tolerancije, dosjedi i tekstura (hrapavost) površina; Predočavanje oblika sa osnovama nacrtne geometrije; Posebnosti u tehničkom crtanju; Tehničko prostoručno skiciranje; Kotiranje; Računarska grafika; Matematička osnova računarske grafike; Stvaranje slikovnog prikaza; Napredne tehnike grafičkog izražavanja; Računalom potpomognuta izrada modela i tehničke dokumentacije proizvoda; Pojednostavnjenja i simboli; Literatura te prilozi: Popis korisnih normi u tehničkom crtanju; Rječnik pojmova iz inženjerske grafike, tehničkog crtanja, dokumentiranja i oblikovanja (dizajna); Neka pravila pisanja oznaka u tehnici i znanosti; Kazalo pojmova; Prilog u boji. Same as in the pre-computer era, the main role and purpose of technical drawing is to give the users of Computer Aided Design (CAD) System traditional knowledge from this field, i.e. to help them develop a sense for connecting 2D and 3D image with the real model, as well as to make users more familiar with a set of conventions or standards typical for technical drawing. In the future, the role of technical drawing is going to change even more due to the fact that with development of computer graphics and its merger with CAM systems, the need for technical drawing in the form of so called "hard copy" is going to decrease, but technical drawing will always be the basis for the mentioned activities. The topics are presented methodically. Wherever possible, theoretical postulates are linked to real machine parts in order to point out the importance of studying this specific area of expertise. This textbook also covers the basics of drawing geometry but not with an intention to replace this discipline. Drawing geometry is used here as a reminder. The authors tried to fill a certain void that exists in this specific area. This textbook is intended for students of engineering faculties in general, but above all to students of mechanical engineering, and also to students of secondary schools, and to all professionals who deal with technical drawing. It could also be a useful reminder to all engineers in practice. 134 ANNUAL REPORT 2010 Pero RAOS & Mladen ŠERCER TEORIJSKE OSNOVE PROIZVODNJE POLIMERNIH TVOREVINA st 1 edition 2010, Size 16,5 × 24 cm, 192 pages, Hardcover Publisher: Mechanical Engineering Faculty in Slavonski Brod ISBN 978-953-6048-57-1 Price: 100,00 kn Contents: Predgovor, Uvod, Uvod u proizvodnju polimernih tvorevina, Polimeri, Teorijske osnove preradbe polimernih taljevina, Dodatak i Kazalo pojmova. This textbook is the product of an extensive scientific-research cooperation of authors in the field of polymer engineering. Together with Postupci proizvodnje polimernih tvorevina (not published yet), this textbook is the basis for the following courses: Polymer processing, Casting, Production procedures, etc. at pregraduate study (at Mechanical Engineering Faculty in Slavonski Brod and at Faculty of Mechanical Engineering and Naval Architecture in Zagreb). However, it can also be used for a more detailed study of polymer processing at postgraduate study of mechanical engineering. Furthermore, this textbook can also be used for other courses dealing with polymer processing, technology and materials. There are four sections in this textbook. The first section deals with similarities in manufacturing of polymer products with the products made from other types of material, primarily metal materials, with special emphasis on special properties of polymers. The second section deals with processing fundamentals. A systematization of polymer processes is also given. The third section explains the processing of synthetic polymers and their structure. There is also a general classification of materials, as well as classification of common polymers. This section also deals with processing properties and application of polymers. The fourth section summarizes the basics of polymer melt processing with special emphasis on flow and rheological behaviour of polymer melts. Polymer processing is based on heat transfer, and therefore, thermal properties of polymers are given. The book provides an extensive list of references to the appropriate technical literature for further study and consideration of current research issues. This textbook was reviewed by: prof. dr. sc. Emil Hnatko (Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek), prof. dr. sc. Tomislav Filetin (Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb), prof. dr. sc. Janez Kopač (Faculty of Mechanical Engineering, University of Ljubljana) and prof. dr. sc. Đurđica Španiček (Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb). This is a practical book aimed at both practicing engineers and graduate students who are engaged in the research and development of polymer processing. 135 ANNUAL REPORT 2010 The open access is available at: http://www.sfsb.hr/nastava/esadrzaji 136 ANNUAL REPORT 2010 Annual Report of MEFSB for 2009 Preface Introduction Josip Juraj Strossmayer University of Osijek Mechanical Engineering Faculty in Slavonski Brod Study Programmes Students Scientific Activities Cooperation with the Economy Management of Faculty Organization and Employees Department for Mechanical Design Department for Production Engineering Department for Materials Engineering Department for Industrial Engineering Chair for Common Subjects Scientific Activities Postgraduate Doctoral Studies in Mechanical Engineering Postgraduate professional studies "Development of products and technologies" Scientific and Research Projects Junior Researchers Defended PhD Thesis Activities of Departments Department for Mechanical Design Department for Production Engineering Department for Materials Engineering Department for Industrial Engineering International Collaboration International Projects Signed Contracts of International Collaboration International Students and Professors Exchange Publications Published Books Tehnički vjesnik - Technical Gazette Strojarstvo - 30 Years of the Faculty of Mechanical Engineering in Slavonski Brod The first issue of Annual Report of Mechanical Engineering Faculty in Slavonski Brod (MEFSB) published in the summer of 2010. The contents of the first issue are given in the right column of this page. Organization of Conferences PLIN 2009 (GAS 2009) Fifth International Scientific-Expert Conference SBW 2009 TEAM 2009 (Technics, Education, Agriculture & Management) Strojarski izazov (Mechanical Engineering Challenge) Locations Map Published Results 137 ANNUAL REPORT 20010 Tehnički vjesnik - Technical Gazette TECHNICAL GAZETTE (TEHNIČKI VJESNIK) (with 17 years of tradition) is the scientific-professional journal of three technical faculties of the University of Osijek: the Faculty of Electrical Engineering in Osijek, the Faculty of Civil Engineering in Osijek and the Mechanical Engineering Faculty in Slavonski Brod. This journal should enable all the researchers, teachers and associates from the University to publish the results of their research, to offer practical solutions for certain problems and to make them available to the general public. Due to high quality, the journal is indexed in several significant bases (INSPEC, SCOPUS, COMPEDEX, GEO Abstracts, Cambridge Scientific Abstracts, etc.), and beginning with Volume 15 (Number 1) in 2008, it is included in Web of Science (SCIExpanded). Hopefully, the journal will be indexed also in SCI and CC. High scientific level of the papers, and high technical quality of the journal are the preconditions for this. Furthermore, there will be 4 numbers annually in the future. Prof. dr. sc. Pero Raos, Editor-in-Chief (since October 2003) The journal is financed by the Ministry of Science, Education and Sports (Republic of Croatia), and also by the Faculty of Electrical Engineering in Osijek, the Faculty of Civil Engineering in Osijek and the Mechanical Engineering Faculty in Slavonski Brod. The journal is published in paper form and in electronic form (without extras) (see: http://hrcak.srce.hr/tehnicki-vjesnik). The members of the Council of Journal are: Radoslav GALIĆ (ETF Osijek) – president, Dražan KOZAK (SF Slavonski Brod) member, Damir MARKULAK (GF Osijek) - member, Ivan SAMARDŽIĆ (Vice-Rector for Science, Technologies, Projects and International Cooperation) - member. 138 ANNUAL REPORT 2010 The members of the Editorial Board are: Pero RAOS (Editor-inChief) (SF Slavonski Brod), Milan KLJAJIN (Vice Editor-inChief) (SF Slavonski Brod), Srete NIKOLOVSKI (ETF Osijek), Snježana RIMAC-DRLJE (ETF Osijek), Goran MARTINOVIĆ (ETF Osijek), Vladimir SIGMUND (GF Osijek), Lidija TADIĆ (GF Osijek), Damir VAREVAC (GF Osijek), Sanja DIMTER (GF Osijek), Ivica KLADARIĆ (SF Slavonski Brod), Tomislav ŠARIĆ (SF Slavonski Brod),Antun STOIĆ (VU Slavonski Brod). The members of the International Editorial Council are: Helmut RAPP (Universität der Bundeswehr München), Matej FISCHINGER (Univerza v Ljubljani), Jožef DUHOVNIK (Univerza v Ljubljani), Janez KOPAČ (Univerza v Ljubljani), Nenad GUCUNSKI (Member, ASCE, Department of Civil and Environmental Engineering at Rutgers University in Piscataway, NJ, USA), Nenad GUBELJAK (Univerza v Mariboru), Jozef NOVAK-MARCINČIN (TU Košice, Slovakia), Karoly BELINA (GAMF Kecskemet, Hungary). The members of the Expert Council are: Academician Božo UDOVIČIĆ (HAZU Zagreb), Tomislav FILETIN and Mladen ŠERCER (Faculty of Mechanical Engineering and Naval Architecture in Zagreb), Ivica DŽEBA (Faculty of Civil Engineering in Zagreb). The volume 17 in numbers Four issues of the journal were published on a total of 552 numbered pages during the year 2010. The structure of 73 published articles was as follows: 31 original scientific paper, 22 preliminary notes, 12 subject reviews and 8 professional papers. http://hrcak.srce.hr/tehnicki-vjesnik 139 ANNUAL REPORT 2010 A special edition of "Strojarstvo" was published in March-April 2010 with the main objective th to celebrate the 35 anniversary of Josip Juraj Strossmayer University of Osijek. 140 ANNUAL REPORT 2010 141 ANNUAL REPORT 2010 Organization of Conferences PLIN 2010 (GAS 2010) Traditional Natural Gas, Heat and Water Conference was held in th st th Osijek (29 September to 1 October 2010) for the 8 time. This st st was also the 1 international conference (1 International Natural Gas, Heat and Water Conference) due to cooperation between the organizers HEP-Plin d.o.o. and Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek with Pollack Mihály Faculty of Engineering in Pécs. Conference Chairs were doc. dr. sc. Zlatko Tonković (HEP-Plin d.o.o.) and prof. dr. sc. Pero Raos (Mechanical Engineering Faculty in Slavonski Brod). The Conference started on 29th September 2010 at HEP-Plin d.o.o. with a round table Construction, Maintenance and Testing of PE Pipes for Gas and Water. The key lecture was held by prof. dr. sc. Pero Raos on polyethylene pipes for gas. Moderators of the round table were prof. dr. sc. Pero Raos, prof. dr. sc. Mladen Šercer, and doc. dr. sc. Zlatko Tonković. Opening Ceremony was held on 30th September 2010 at Croatian National Theater in Osijek and it was moderated by doc.dr.sc. Damir Pečvarac (Member of Board - HEP d. d.). Welcoming address was held by doc. dr. sc. Zlatko Tonković (HEP-Plin d. o. o.), prof. dr. sc. Dražan Kozak (the Dean of MEF in Slavonski Brod), and prof. dr. sc. Bálint Bachmann (the Dean of Pollack Mihály Faculty of Engineering in Pécs). 30 papers were presented at this conference (divided in five sections entitled: Legislation; Energetics; Health and Ecology; Gas Technique; General, Water and Fuels). Lecturers were not only renowned university professors, experts and entrepreneurs from Croatia but also from abroad. The lectures at this conference were based on renewable energy sources, use of natural gas, heating systems and water supply systems. 30 papers were presented orally and additional 6 were part of the poster session (dealing with heating systems and water supply systems). Prof. dr. sc. Pero Raos moderated the closing ceremony of this international scientific-expert conference. Dr. habil. Bálint Bachmann, Dean of the Pollack Mihály Faculty of Engineering, University of Pécs Round table at HEP-Plin d. o. o. Osijek Lecture held by prof. dr. sc. Pero Raos (29 September 2010) This conference gains in importance each year, and in 2010, there were more than 300 participants from Croatia, Bosnia and Herzegovina, Hungary, Germany, Slovenia and Serbia. The main objective of this conference was to enrich the knowledge of the experts in the field of engineering, with special emphasis on gas, heat and water. The conference is included in professional training pursuant to the Regulations on Professional Examinations and Professional Training of Persons Performing Civil Engineering Jobs (with 16 credits). Opening Ceremony doc. dr. sc. Damir Pečvarac (HEP d. d.) 142 ANNUAL REPORT 2010 TEAM 2010 (Technics, Education, Agriculture & Management) The 2nd International Scientific and Expert Conference TEAM 2010 was held in Kecskemét (Hungary) on 4 and 5 November 2010. This Conference was organized by the International TEAM Society: University of Applied Sciences of Slavonski Brod, Mechanical Engineering Faculty in Slavonski Brod and GAMF Kecskemét College, Hungary. The aim of the Conference is transfer of knowledge and dissemination of achievements in the field of Technics, Education, Agriculture and Management (therefore TEAM). There were more than 70 papers at the First TEAM Conference, and this year the interest was even greater and over 100 papers were presented. Although the Conference was in Hungary, there were many participants from Croatia who presented the papers and also helped with the organization of the Conference. Mechanical Engineering Faculty in Slavonski Brod (students): Tomislav Baškarić, Antonio Koljenik, Zvonimir Janković, Darko Damjanović and Mario Holik Since one of the goals of the International TEAM Society is to support young scientists and experts, five students of Mechanical Engineering Faculty in Slavonski Brod also participated. One of them is Darko Damjanović who received the Best Paper and PresentationAward. This Conference is the proof of good cooperation between higher education institutions. Hopefully, it will become a tradition with even greater number of participants and quality scientific papers. Mechanical Engineering Faculty in Slavonski Brod was represented by: Tomislav Baškarić, Mario Holik, Zvonimir Janković, Ivan Samardžić, Pero Raos, Dražan Kozak, Antonio Koljenik, Marija Živić, Antun Stoić, Tomislav Šarić and Ivica Kladarić. rd The 3 International Scientific and Expert Conference TEAM 2011 will be held in Trnava, Slovak Republic. 143 ANNUAL REPORT 2010 Strojarski izazov (Mechanical Engineering Challenge) The cooperation between Đuro Đaković Montaža and Mechanical Engineering Faculty in Slavonski Brod started in 2006 and resulted in the organization of the first "Strojarski izazov" (Mechanical Engineering Challenge) in 2007 with the main purpose to show how knowledge and experience can be successfully brought together. This is a unique manifestation in the field of mechanical engineering in the Republic of Croatia. At SI, renowned experts and professors (from MEF and guest lecturers) hold lectures in order to show new developments in different fields of mechanical engineering to present and future students of MEF and guests from the economy. The 4th SI was held on 29-30 April 2010 at Mechanical Engineering Faculty in Slavonski Brod. The topic of SI was Energetics and current situation in the Republic of Croatia, as well as national energy strategy. Key lectures on this topic were held by: academician Božo Udovičić, dr. sc. Goran Granić, Head of Energy Institute Hrvoje Požar and prof. dr. sc. Igor Dekanić from the Faculty of Mining, Geology and Petroleum Engineering (University of Zagreb). Professors from MEF held lectures on application of new technology in the field of energetics, while the representatives from Đ.Đ. Montaža tried to show some of the challenges in this field by using some examples from practice. On the second day of SI, the visitors were able to attend short lectures which were held by young researchers and graduate students of mechanical engineering (MEF in Slavonski Brod), as well as different quizzes and workshops intended for students and high school graduates. They could also learn more about the advantages of studying at MEF. Approximately 500 high school graduates, students and representatives of the local political community (Town of Slavonski Brod, Brod-Posavina County), the economy and the media, attended this manifestation. 144 ANNUAL REPORT 2010 ICMEM 2010 The 1st International Scientific Conference on Manufacturing Engineering & Management 2010 took place on 21 - 23 November 2010 in one of the most dynamic cities of Slovakia Prešov with a beautiful renovated city centre and youthful atmosphere. Conference was organized by: ? ? ? ? Department of Manufacturing Management, Faculty of Manufacturing Technologies, Technical University of Košice with a seat in Prešov Mechanical Engineering Faculty in Slavonski Brod, J. J. Strossmayer University of Osijek, Croatia, Faculty of Management Czestochowa University of Technology, Poland, Faculty of Economic Sciences Valahia University of Targoviste, Romania. in cooperation with: ? ? ? ? ? Institute of Geonics, Academy of Science, Ostrava - Poruba, Czech Republic, Regional Advisory and Information Centre Prešov (RAIC), Slovakia, Euro Info Centre SK 673, Municipality of Prešov (Slovak Republic), Municipality of Slavonski Brod (Croatia). The aim of the conference was to provide the most complete and reliable source of information on current developments in the field. Further aim of ICMEM2010 was to establish channels of communication and disseminate knowledge among professionals working in manufacturing, related industries and services, investment institutions, as well as experts and researchers in relevant research and academic institutions in the field of Manufacturing Engineering and Manufacturing Management. Conference Chairman Prešov Hloch Sergej,Assoc. Prof. Ing. PhD., TU of Košice, Slovakia Kozak Dražan, Prof. dr. sc., University of Osijek, Croatia Valíček Jan, Assoc. Prof. Ing. PhD., VŠB TU Ostrava, Czech Republic 145 ANNUAL REPORT 2010 Students’ Activities Study Visit to SAME DEUTZ-FAHR Žetelice d.o.o. in Županja SAME DEUTZ-FAHR Žetelice d.o.o. in Županja manufactures harvesting machinery and uses highly qualified manpower. This is a modern and sophisticated factory with stateof-the-art equipment for laser cutting, cataphoresis painting, welding process optimization, etc. Students and their professors had a chance to see a design office dealing with development of various kinds of harvesting machinery using computer tools. This well-organized factory has specialized in providing specific and tailored solutions to customer applications and also aims at constant improvement of their standard products, i.e. harvesting or treshing machinery. Students could also see the whole production process of harvesting machinery starting with material preparation, laser cutting, deformation, welding, painting, and ending with assembly of the final product. Students of Graduate study (module: Product design and development, III. semester) with their professors during the visit to SAME DEUTZ-FAHR Žetelice d.o.o. in Županja (10 June 2010) Students of Graduate study (module: Product design and development, II. semester) with their professors during the visit to SAME DEUTZ-FAHR Žetelice d.o.o. in Županja (17 November 2010) 146 ANNUAL REPORT 2010 Study Visit to TŽV GREDELJ d.o.o. in Zagreb On 15 December 2010, the students of MEF (Graduate study Mechanical Engineering; module: Product design and development) visited TŽV GREDELJ d.o.o. Part of this study visit were also prof. dr. sc. Milan Kljajin, prof. dr. sc. Željko Ivandić, and assistants: dr. sc. Mirko Karakašić, Mato Kokanović, Tomislav Baškarić and Darko Damjanović. Prof. dr. sc. Milan Kljajin arranged this visit with the President of the Board of Directors of TŽV GREDELJ d.o.o., mr. sc. Ivan Tolić. The students had a chance to visit the new factory facilities in the Industrial zone Vukomerec in Zagreb. Gojko Stunjek, dipl. ing. welcomed the group and pointed out some interesting facts about the factory: TŽV GREDELJ d.o.o. was founded in 1894 as the main workshop of the Hungarian State Railways for repair and general overhaul of steam locomotives. Since then, this company has been continuously investing in its manufacturing capabilities, technologies, and human and material resources. Today, TŽV GREDELJ d.o.o. is a respectable participant in the rolling stock market, with a full range portfolio of new rolling stock products for urban, suburban and regional transport. As a provider of various levels of services for the rolling stock, from repair to complete reconfiguration, TŽV GREDELJ d.o.o. has exceptionally strong references in successful repowering and modernization of rolling stock of various OEM manufacturers from all around the world. Students and professors at TŽV GREDELJ d.o.o. 147 ANNUAL REPORT 2010 Sports Activities rd 3 Memorial Indoor Soccer Tournament "Stevica Šovakov" In memoriam of Stevica Šovakov, a student at Mechanical rd Engineering Faculty in Slavonski Brod, the 3 Memorial Indoor Soccer Tournament was held in the Village of Gajić (Baranja). There were 12 teams at this tournament, primarily Stevica's friends from Baranja, Županja, as well as guests from Hungary and MEFSB. The MEFSB team won the Trophy. Prof. Marušić presented trophies to the team captains. Prof. Marušić pointed out that Stevica was a kind and brave young man who is still remembered by professors at Mechanical Engineering Faculty in Slavonski Brod and by his fellow students. Despite the difficult illness, he always persisted in his studies, and he was always the role model for others. He can be an inspiration to all of us when the times are difficult. Stevica Šovakov Rowing Regatta The 18th Rowing Regatta for students of mechanical engineering and naval architecture in Croatia was held on 18 September 2010 at Jarun (Zagreb). Mechanical Engineering Faculty in Slavonski Brod was represented by Alegić Dino, Fridl Mario, Halavuk Dino, Legac Vjekoslav, Majdančić Ivan and Pinjušić Mihael (lead by mr. sc. Zvonko Miljković). They won a bronze medal in a coxed four (4+) in extremely difficult conditions. The coxswain was Krunoslav Šešet (Faculty of Mechanical Engineering and Naval Architecture, Zagreb). Mr. sc. Zvonko Miljković and Prof. dr. sc. Dražan Kozak, the Dean of MEFSB, with students' crew 148 ANNUAL REPORT 2010 Huawei Summer Camp 2010 China (Hong Kong, Shenzhen, Shanghai) Hong Kong Shanghai China Pavilion is indeed the most impressive building at the EXPO. China is one of the countries that are aware of the fact that nature and environment must be preserved at all cost. Darko Damjanović, student of Mechanical Engineering Faculty in Slavonski Brod, was one of the top (11) students in Croatia who won a scholarship from one of the biggest high-tech companies in the world: Huawei Technologies, China. This scholarship was part of the project "Huawei Summer Camp 2010" organized by the Chinese company Huawei Technologies and Office of the President of the Republic of Croatia. The scholarship covered all the expenses for the trip to People's Republic of China in the time period of 24 to 31 July 2010 and visit to some of the largest cities in China: Hong Kong, Shenzhen, and Shanghai. A place where "East meets West" is geographically located in southern China with an area of approximately 1100 km2 and a population of 7 million people. Hong Kong is one of the most densely populated areas in the world. City view from Victoria Peak is something truly breathtaking. Cameras simply cannot capture the full grandeur of Hong Kong; you simply have to be there! Shenzhen is located north of Hong Kong and almost twice as big as Hong Kong. Shenzhen is home of Huawei which is one of the most successful high-tech companies in the world. The tour of this great company made quite an impression because everything is covered with green (inside, as well as outside the company). This is an ultra-modern company with many employees, with many products and innovations, and with a huge number of people in the development centre. Shanghai is one of the largest metropolitan areas in the world and definitely the largest city in China with more than 20 million people. It is located on China's central eastern coast at the delta of the Yangtze River. One of the many beautiful and memorable experiences is a visit to Yuyuan Garden. This classical Chinese garden was first established 500 years ago during the Ming Dynasty. It is a place where you can forget the city noise and hustle, a place where you feel relaxed and satisfied, exactly what the Chinese word "Yu" means. The total opposite is the Oriental Pearl TV Tower (by the side of Huangpu River). At 468 m high, it was the tallest structure in China from 1994–2007, when it was surpassed by the Shanghai World Financial Center. The tower has fifteen observatory levels and the highest (known as the Space Module) is at 350 m. The project also contains exhibition facilities, restaurants and a shopping mall. And finally – EXPO 2010 entitled "Better City, Better Life"! It is fascinating that there were huge queues in front of the pavilions despite the fact that it was over 40 °C. By the end of EXPO 2010, there were at least 70 million visitors from all over the world. 149 ANNUAL REPORT 2010 Social Activities Visit to Zagreb and Krapina Bodies Revealed (Zagreb) and Krapina Neanderthal Museum The management of the Mechanical Engineering Faculty in Slavonski Brod, together with the Independent Union of Research and Higher Education Employees of Croatia (NSZiVO) Slavonski Brod branch at the MEFSB, have organized an excursion to Zagreb (the exhibition Bodies Revealed at Klovićevi Dvori) and Krapina (the Krapina Neanderthal Museum) on 6th June 2010. Many employees of the Mechanical Engineering Faculty and members of their families took part in this excursion. As part of a world tour, the exhibition Bodies Revealed was opened at Klovićevi dvori in Zagreb on 9th April 2010. This worldfamous anatomical exhibition has been seen by millions of visitors worldwide. The exhibition features a groundbreaking new design with video and interactive features, modern lighting and an open floor plan that allows visitors to experience each gallery at their own leisurely pace-exploring the skeletal, muscular, reproductive, respiratory, circulatory and other systems of the human body, giving visitors the opportunity to view the complexity of their own organs and systems. The exhibition features more than 200 specimens, including 14 whole body specimens posed in a combination of dramatic athletic and artistic movement. The real human body specimens in the exhibition are preserved through a revolutionary technique called polymer preservation. In this process, human tissue is permanently preserved using liquid silicone rubber. All of the bodies and organ specimens in Bodies Revealed came from individuals who chose to donate their bodies to accredited medical universities in the People's Republic of China. 150 ANNUAL REPORT 2010 The museum visit was followed by a lunch at Roses Fashion Outlet in Sveti Križ Začretje. After lunch, a visit to the Krapina Neanderthal Museum followed. This Museum, renovated according to world standards, is uniquely located and has become an attraction not to be missed. The site itself is protected as the first paleontological nature monument in Croatia. Much effort, knowledge, and money (around 8.5 million Euros) was invested into the renovation of the Krapina Neanderthal Museum. Here, visitors can see and get to know the ancestors of modern man, who inhabited a large part of the European continent, as well as parts of south-western Asia, and died out around the year 30,000 B.C. After the habitat of the Krapina Neanderthal at Hušnjakovo was discovered in 1899 by Dragutin Gorjanoviæ Kramberger; geological and paleontological research continued until 1905. The age of the rich site was determined to be over 130,000 years and around 900 fossilized human bones, as well as numerous stone tools from the Paleolithic Era, were uncovered at the site. Moreover, fossil remains of bears, wolves, moose, deer, rhino, wild cattle and other animals were also found in the caves. The museum is located in the valley between the two hills of Hušnjakovo and Josipovac, where an artificial semi-cave, actually larger than the real one, was constructed with the help of modern technology. The museum covers two floors with a total area of 1,200 square meters. The entrance blends into the landscape so, upon entering, visitors are imparted with an impression that they have become the cave's inhabitants. This impression is additionally enhanced by interactive content: visitors "travel" through history from the big bang to the beginning of the world, following the evolution of the Earth, the development of the first organisms, dinosaurs, the life of first hominids who came down from the branches, all the way to the Neanderthal of Krapina, who are represented by hyperrealistic sculptures. The museum is equipped with top class technological equipment and numerous classic contents such as info-booths, a cafe, and a large library. 151 ANNUAL REPORT 20010 Advent in Vienna The management of the Mechanical Engineering Faculty in Slavonski Brod, together with the Independent Union of Research and Higher Education Employees of Croatia (NSZiVO) Slavonski Brod branch at the MEFSB, have organized a two-day excursion to Vienna called 'Avent in Vienna'. Due to a huge interest, it was necessary to apply early in order to experience the magic ofAdvent in Vienna (11-12 December 2010). This was an exceptional opportunity to explore Vienna and to visit some of the most famous places like the Opera, Hofburg, Schönbrunn, City Hall, Kunstforum, Hundertwasserhaus, as well as some of the museums. We also experienced the typical Viennese coffee house atmosphere at Café Sacher that offers an original Sacher-Torte. Vienna is at its absolute best at the end of the year and the Christmas Market on Vienna's City Hall Square is an unforgettable highlight for all visitors eager to get into the Christmas spirit. The unique backdrop of the Burgtheater and Vienna City Hall gives this Christmas Market a charm of its own. The delicious aroma of punch, traditional gingerbread, roasted almonds and honey puts everyone in the Christmas mood. The Christmas Market is a favourite place to meet, with many visitors returning several times each season. Young families, teens and tourists are particularly enchanted by the festive atmosphere on City Hall Square. The vibrant and colourful Christmas Market offers a vast array of Christmas handicrafts, tree decorations and other gift ideas. Evocative Advent aromas, festive concerts, a tall tree blazing with countless Christmas lights, and the enchantingly decorated Rathauspark are just some of the highlights that give Vienna the unique appeal. 152 ANNUAL REPORT 2010 In Memoriam Dragutin Vujčić, mag. iur. Secretary of Mechanical Engineering Faculty, Dragutin Vujčić, passed away on 22 August 2010 Dragutin Vujčić was born on 25 February 1944 in Staro Topolje. He finished elementary school in Donji Andrijevci, and high school (field: economics) in Bosanski Brod. He graduated from Faculty of Law, J. J. Strossmayer University of Osijek. Furthermore, he enrolled postgraduate study at Faculty of Law in Osijek, where he passed all exams but did not defend his master thesis due to his enlistment during the Homeland War. He worked in the economy, and later for state administration (Municipality of Slavonski Brod from 1966 to 1970) and later again in the economy (Oriolik Oriovac, A.K. Jasinje, etc.) until 1976 when he became the Secretary of FSB Centre for Mechanical Engineering Studies in Slavonski Brod, which became later an independent scientific-educational institution known as Mechanical Engineering Faculty in Slavonski Brod (forming a constituent part of J. J. Strossmayer University of Osijek). As reward for his valuable contributions and hard work, the Secretary of Mechanical Engineering Faculty in Slavonski Brod, Dragutin Vujčić, mag. iur., received a medal from Town of Slavonski Brod in 1979 for 'his contribution in the founding of Mechanical Engineering Faculty in Slavonski Brod'. Mr Vujčić will be remembered for his selfless contribution in organisation of classes at Mechanical Engineering Faculty during the Homeland War. Furthermore, he was also a participant of this war, for which he received the Homeland War Memorial (19911992) and a number of rewards for his work. It should be emphasised that Dragutin Vujčić helped in the founding of Student Centre in Slavonski Brod, and on 30 March 1995, he was appointed Director of Student Centre by the Council of University of Osijek. Much of his work was dedicated to coordination of all higher education institutions in the Town of Slavonski Brod. His great enthusiasm and valuable contribution to improvement of higher education system in the Town of Slavonski Brod, Brod-Posavina County and Easern Croatia are highly appreciated. He will be greatly missed by all employees of Mechanical Engineering Faculty in Slavonski Brod. 153 ANNUAL REPORT 2010 More information http://www.sfsb.hr 154 ANNUAL REPORT 2010 Published Results The result of the scientist's work on many projects is a great number of papers published on international conferences in the country and abroad and in the international journals. More details about books and published papers are available at the web page of Croatian Scientific Bibliography - http://bib.irb.hr Published books: 1. Kljajin, Milan; Opalić, Milan. Inženjerska grafika. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 2010. (sveučilišni udžbenik). [CROSBI-ID 482090] 2. Raos, Pero; Šercer, Mladen. Teorijske osnove proizvodnje polimernih tvorevina. Slavonski Brod/Zagreb: Strojarski fakultet u Slavonskom Brodu, 2010. (visokoškolski udžbenik). [CROSBI-ID 491516] Text books and scripts: 3. Budić, Ivan. Osnove tehnologije kalupljenja - Jednokratni kalupi I. dio, II. izmijenjeno i dopunjeno izdanje. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 2010. [CROSBI-ID 442822] Journal articles and review articles in CC journals: 4. Aleksandrović, Srbislav; Marušić, Vlatko; Vujinović, Tomislav; Maglić, Leon. Influence of Variable Blank Holding Force and Nonmonotonous Process of Deep Drawing on Formability of Coated Sheets. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010), 2; 159168 (prethodno priopćenje, znanstveni). [CROSBI-ID 472676] 5. Cvetković, Slavica; Šimunović, Goran; Maglić, Leon. Modelling of Logistic System by Petri Nets. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010), 2; 169179 (prethodno priopćenje, znanstveni). [CROSBI-ID 472773] 6. Dunđer, Marko; Vuherer, Tomaž; Kladarić, Ivica. Weldability Investigation of TStE 420 After Weld Thermal Cycle Simulation. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010) , 2; 97-104 (članak, znanstveni). [CROSBI-ID 472675] 7. Grizelj, Branko; Cumin, Josip; Grizelj, Dejan. Effect of spring-back and spring-forward in V-die bending of St1403 sheet metal plates. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010), 2; 181-186 (prethodno priopćenje, znanstveni). [CROSBI-ID 474340] 155 ANNUAL REPORT 2010 8. Marušić, Sanja; Marušić, Vlatko; Samardžić, Ivan. The Quality Influence of Base Material Surface Preparation on the Durability of a Sprayed Layer Against Radial and Axial Shear. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010), 2; 187-196 (prethodno priopćenje, znanstveni). [CROSBI-ID 472778] 9. Milošević-Mitić, Vesna; Kozak, Dražan; Maneski, Taško; Anđelić, Nina; Gaćeša, Branka; Stojkov, Marinko. Dynamic Nonlinear Temperature Field in a Ferromagnetic Plate Induced by High Frequency Electromagnetic Waves. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010), 2; 115-124 (članak, znanstveni). [CROSBI-ID 474538] 10. Novak-Marcinčin, Jozef; Doliak, Martin; Hloch, Sergej; Ergić, Todor. Application of the Virtual Reality Modelling Language to Computer Aided Robot Control System ROANS. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010), 2; 227-232 (članak, znanstveni). [CROSBI-ID 479762] 11. Opalić, Milan; Kljajin, Milan; Vučković, Krešimir. Disassembly Layout in WEEE Recycling Process. // Strojarstvo. 52 (2010), 1; 51-58 (pregledni rad, znanstveni). [CROSBI-ID 459302] 12. Pušavec, Franci; Stoić, Antun; Kopač, Janez. Sustainable Machining Process - Myth or Reality. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010), 2; 197-204 (prethodno priopćenje, znanstveni). [CROSBI-ID 472781] 13. Šimunović, Goran; Balič, Jože; Šarić, Tomislav; Šimunović, Katica; Lujić, Roberto; Svalina, Ilija. Comparison of the technological time prediction models. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010.), 2; 137-145 (članak, znanstveni). [CROSBI-ID 472859] 14. Šoštarić, Damir; Vinko, Davor; Žagar, Drago; Samardžić, Ivan. Reliability of Welding Parameters Monitoring System. // Strojarstvo. 52 (2010), 2; 217-226 (članak, znanstveni). [CROSBI-ID 458604] 15. Trišović, Nataša; Maneski, Taško; Kozak, Dražan. Developed procedure for dynamic reanalysis of structures. // Strojarstvo: časopis za teoriju i praksu u strojarstvu. 52 (2010), 2; 147-158 (članak, znanstveni). [CROSBI-ID 474540] 156 ANNUAL REPORT 2010 Scientific articles in other journals: 16. Adamović, Dragan; Mandić, Vesna; Jurković, Zoran; Grizelj, Branko; Stefanović, Milentije; Marinković, Tomislav; Aleksandrović, Srbislav. An Experimental Modelling and Numerical FE Analysis of Steel-Strip Ironing Process. // Tehnički vjesnik: znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 4; 435444 (članak, znanstveni). [CROSBI-ID 496969] 17. Aračić, Stjepan; Krumes, Dragomir; Matičević, Tatjana; Vilovčević, Ivica. Analiza izdržljivosti ekoloških premaza u zaštiti metala od korozije. // Tehnički vjesnik: znanstvenostručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 3; 343-346 (prethodno priopćenje, znanstveni). [CROSBI-ID 497822] 18. Aračić, Stjepan; Krumes, Dragomir; Matičević, Tatjana; Vilovčević, Ivica. Testing the durability of ecologic coats in the protection of metals from corrosion. // Tehnički vjesnik : znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 2; 125-130 (pregledni rad, znanstveni). [CROSBI-ID 469323] 19. Aračić, Stjepan; Krumes, Dragomi r; Vitez, Ivan. Tribocorrosion of Low Carbon Steel C15E in 5 % NaCl and 5 % NaCl + SiO2. // Metalurgija. 49 (2010), 2; 111-114 (prethodno priopćenje, znanstveni). [CROSBI-ID 439531] 20. Crnković, Damir; Šljivac, Damir; Stojkov, Marinko. Influence of Wind Power Plants on Power System Operation – Part One: Wind Power Plant Operation and Network Connection Criteria. // Tehnički vjesnik: znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 1; 101-108 (pregledni rad, znanstveni). [CROSBI-ID 443925] 21. Crnković, Damir; Vrandečić, Nino; Stojkov, Marinko. Transients in No-Load Condition of Power Transformer 20/0, 4 kV. // Tehnički vjesnik: znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 2; 179183 (članak, znanstveni). [CROSBI-ID 498069] 22. Čatić, Igor; Barić, Gordana; Cvjetičanin, Nenad; Galić, Kata; Godec, Damir; Grancarić, Ana Marija; Katavić, Ivan; Kovačić, Tonka; Raos, Pero; Rogić, Ana; Rujnić-Sokele, Maja; Vranješ, Nina; Vrsaljko, Domagoj; Andričić, Branka. Polimeri - od prapočetka do plastike i elastomera. // Polimeri. 31 (2010), 2; 59-70 (pregledni rad, znanstveni). [CROSBI-ID 494900] 157 ANNUAL REPORT 2010 23. Garašić, Ivica; Ćorić, Anto; Kožuh, Zoran; Samardžić, Ivan. Occurence of cold cracks in welding of high-strength S960QL steel. // Tehnički vjesnik: znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 3; 327-335 (prethodno priopćenje, znanstveni). [CROSBIID 489413] 24. Grizelj, Branko; Cumin, Josip; Seuček, Ivan; Šoškić, Nikola; Vujčić, Branimir. Effect of spring-back and Spring forward in V-die bending of St1403 sheet metal plates. // Metalurgija. 49 (2010), 3; 230-230 (sažetak, znanstveni). [CROSBI-ID 475988] 25. Hornung, Krunoslav; Hnatko, Emil; Stojkov, Marinko; Kljajin, Milan. Natural gas savings using solar heating. // Tehnicki vjesnik / Technical Gazette. 17 (2010), 4; 515-522 (prethodno priopćenje, znanstveni). [CROSBI-ID 496861 26. Hreha, Pavol; Hloch, Sergej; Magurova, Dagmar; Valiček, Jan; Kozak, Dražan; Harničarova, Marta; Rakin, Marko. Water Jet Technology Used in Medicine. // Tehnički vjesnik: znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 2; 237-240 (pregledni rad, znanstveni). [CROSBI-ID 476496] 27. Hreha, Pavol; Hloch, Sergej; Valíček, Jan; Monková, Katarína; Monka, Peter; Harničárová, Marta; Fusek, Martin; Konjatić, Pejo. Impact of abrasive mass flow rate when penetrating into a materialon its vibration. // Tehnicki vjesnik-Technical gazette. 17 (2010), 4; 475-480 (prethodno priopćenje, znanstveni). [CROSBI-ID 496940] 28. Karakašić, Mirko; Zadnik, Žiga; Kljajin, Milan; Duhovnik, Jože. Functional structure generation within multistructured matrix forms. // Tehnicki vjesnik / Technical Gazette. 17 (2010), 4; 465-473 (izvorni znanstveni članak, znanstveni). [CROSBI-ID 496857] 29. Kliber, J.; Fabik, R.; Vitez, Ivan; Drozd, K. Hot forming recrystallization kinetics in steel. // Metalurgija. 49 (2010), 1; 67-71 (pregledni rad, znanstveni). [CROSBI-ID 469852] 30. Kozak, Dražan; Ivandić, Željko; Konjatić, Pejo. Determination of the critical pressure for a hot-water pipe with a corrosion defect. // Materiali in tehnologije. 44 (2010), 6; 385-390 [CROSBI-ID 496137] 31. Kozak, Dražan; Konjatić, Pejo; Matejiček, Franjo; Damjanović, Darko. Weld Misalignment Influence on the Structural Integrity of Cylindrical Pressure Vessel. // Structural Integrity and Life. 10 (2010) , 2; 153-159 (članak, znanstveni). [CROSBI-ID 477597] 158 ANNUAL REPORT 2010 32. Marušić, Vlatko; Aračić, Stjepan; Samardžić, Ivan. The influence of the base material surface preparation on the properties of thermally sprayed coatings. // Metalurgija. 49 (2010); 53- 56 (prethodno priopćenje, znanstveni). [CROSBI-ID 425288] 33. Pešić, Radivoje; Petković, Snežana; Hnatko, Emil; Veinović, Stevan. Antropogeno globalno zagrevanje i obnovljive energije. // Traktor i pogonske mašine. 15 (2010), 2/3; 101-108 (pregledni rad, znanstveni). [CROSBI-ID 498119] 34. Samardžić, Ivan; Bajić, Darko; Klarić, Štefanija. Influence of the activating flux on weld joint properties at arc stud welding process. // Metalurgija. 49 (2010), 4; 325-329 (prethodno priopćenje, znanstveni). [CROSBI-ID 478523] 35. Samardžić, Ivan; Kožuh, Zoran; Mateša, Branko. Structural analysis of three-metal explosion joint: Zirconium Titanium - Steel. // Metalurgija. 49 (2010.), 2; 119-122 (prethodno priopćenje, znanstveni). [CROSBI-ID 439420] 36. Solenički, Goran; Budić, Ivan; Ciglar, Damir. Determination of thermal conductivity in foundry mould mixtures. // Metalurgija. 49 (2010), 1; 3-7 (članak, znanstveni). [CROSBI-ID 439901] 37. Stoić, Antun; Lacković, Ivica; Kopač, Janez; Samardžić, Ivan; Kozak, Dražan. An investigation of machining efficiency of internal roller burnishing. // Journal of achievements in materials and manufacturing engineering. 40 (2010), 2; 188-194 (članak, znanstveni). [CROSBI-ID 476857] 38. Baličević, Pavo; Ivandić, Željko; Kraljević, Drago. Temperature transitional phenomena in spherical reservoir wall. // Tehnički vjesnik: znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 1; 31-34 (članak, znanstveni). [CROSBI-ID 468788] 39. Stojkov, Marinko; Šljivac, Damir; Jozsa, Lajos. Electric and Magnetic Field Computation of 35 kV Voltage Level of Transformer Substation 35/10 kV Using CDEGS Software. // Acta Electrotechnica et Informatica Journal. 10 (2010), 4; 64-68 (članak, znanstveni). [CROSBI-ID 486227] 40. Šercer, Mladen; Raos, Pero; Rujnic-Sokele, Maja. Thermal Properties of Bio- and Synthetic-Based PUR Foams. // International Journal of Material Forming. 3 (2010), Suppl. 1; 535-538 (članak, znanstveni). [CROSBI-ID 474075] 159 ANNUAL REPORT 2010 41. Živić, Marija; Galović, Antun; Ferdelji, Nenad. Local entropy generation during steady heat conduction through a plane wall. // Tehnički vjesnik: znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010.), 3; 337341 (članak, znanstveni). [CROSBI-ID 487284] Nonscientific papers in other journals: 42. Kiš, Darko; Stoić, Antun; Žagar, Drago; Sito, Stjepan. The contents of carcinogenic PAHs on corn seeds and the energy efficiency of drying by different energy sources. // Tehnički vjesnik: znanstveno-stručni časopis tehničkih fakulteta Sveučilišta u Osijeku. 17 (2010), 3; 285-288 (članak, ostalo). [CROSBI-ID 499665] 43. Raos, Pero; Stojšić, Josip; Somolanji, Marija. Polymeric metal-filled compounds. // Metalurgija. 49 (2010) 3; 215215 (sažetak, stručni). [CROSBI-ID 472674] 44. Samardžić, Ivan; Sigurnjak, Mato; Novak, Dušan. Automatsko MAG zavarivanje nosača željezničkog vagona za transport kontejnera. // Zavarivanje. 53 (2010), 3/4; 83-91 (članak, stručni). [CROSBI-ID 485466] Conference reports (abstracts) in other journals: 45. Hadžiahmetović, Halima; Klarić, Štefanija; Kladarić, Slavica; Sunulahpašić, Raza. Revitalization of steam pipeline wall thickness // Metalurgija / Alfirević, I; Samardžić, I; Dibatkin, S. (ur.). Zagreb: Hrvatsko Metalurško Društvo, 2010. 214-214 (poster, međunarodna recenzija, sažetak,stručni). [CROSBI-ID 477679] 46. Samardžić, Ivan; Bajić, Darko; Stoić, Antun; Klarić, Štefanija. Influence of the activating flux on weld joint properties at arc stud welding process // Metalurgija / Alfirević, I; Samardžić, I; Dibatkin, S. (ur.). Zagreb: Hrvatsko Metalurško Društvo, 2010. 214-214 (poster, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 477683] 47. Samardžić, Ivan; Klarić, Štefanija; Kladarić, Ivica; Hadžiahmetović, Halima; Marković, Radojka. Analysis of weld properties at flux-cored arc welding // Advanced materials and operations / Makedonski, Boris; Makedonski, Aleksandar; Georgieva, Ina (ur.). Sofia: St. Ivan Rilski, 2010. 20-20 (poster, međunarodna recenzija, sažetak). [CROSBI-ID 496456] 160 Participants from MEFSB at the conference AMO 2010 (Advanced Materials and Operations) in Varna, Bulgaria ANNUAL REPORT 2010 48. Stoić, Antun; Duspara, Miroslav. Water jet cutting and its application for destruction of munition // Advanced Materials and operations / Makedonski, Boris; Makedonski, Aleksandar; Georgieva, Ina (ur.). Sofia: St. Ivan Rilski, 2010. 32-32 (predavanje, međunarodna recenzija, sažetak, stručni). [CROSBI-ID 496454] Invited lectures on conferences: Oral-presentation of Josip Cumin at the conference AMO 2010 (Advanced Materials and Operations) in Varna, Bulgaria 49. Samardžić, Ivan; Kozak, Dražan; Kladarić, Ivica; Stoić, Antun; Ivandić, Željko. Experience in Welding Parameters Data Monitoring // New Ways in Manufacturing Technologies / Monka, Peter ; Monkova, Katarina (ur.). Prešov: Technical University of Košice, 2010. 41-52 (pozvano predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 476371] Plenary/keynote talks: 50. Kopač, Janez; Pušavec, Franci; Stoic, Antun. Sustainable Technology Solution by Cryogenic Machining: Influence of Cryogenic Fluid Phase on Machining Performance // Proceedings of the 1st International conference of Sustainable Life in Manufacturing SLIM 2010 / Oguz Colak; Kopač, Janez (ur.). Isparta: Suleyman Demirel UNiversity CAD/CAM Research and Application Center & University of Ljubljana Faculty of Mechanical Engineering Laboratory for cutting, 2010. 6-12 (plenarno predavanje, međunarodna recenzija, objavljeni rad). 51. Kozak, Dražan; Ivandić, Željko; Živić Marija; Damjanović, Darko. CFD analysis of originally designed car body in order to improve aerodynamic // Proceedings of the 2nd International Scientific and Expert Conference TEAM 2010 / Arpad, Ferencz; Klebniczki Jozsef; Lipoczine, Csabai; Borsne, Judit; Csaba, Fabian (ur.). Kecskemet: Kecskemeti Foiskola, 2010. 24-41 (plenarno predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490068] 52. Marušić, Vlatko; Milinović, Andrijana; Marušić, Sanja. Aktualnost tribološkog pristupa problemu trošenja pužnih presa za cijeđenje ulja // Proceedings of 1st International Scientific Conference on Economic and Regional Development / Oliver Momčilović (ur.). Zrenjanin: TQM Center, 2010. 460-467 (plenarno predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 496370] 161 ANNUAL REPORT 2010 53. Samardžić, Ivan; Stoić, Antun; Kladarić, Ivica; Dunđer, Marko. Modern materials and technologies in steam boiler power plant production // Procedings of the 2ND International scientific and expert conference TEAM 2010 / Árpád, Ferencz; József, Klebniczki; Sarolta, Csabai; Judit, Pető; Csaba, Fábián (ur.). KECSKEMÉT: KECSKEMÉT COLLEGE, 2010. 42-48 (plenarno predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490501] Scientific conference papers with international peerreview: 54. Baškarić, Tomislav; Damjanović, Darko; Matejiček, Franjo; Kozak, Dražan; Ivandić, Željko. Stress analysis of thickwalled tubes with different degrees of plasticization // Proceedings of the 2nd International Scientific and Expert Conference TEAM 2010 / Arpad, Ferencz ; Klebniczki Jozsef; Lipoczine, Csabai; Borsne, Judit; Csaba, Fabian (ur.). Kecskemet: Kecskemeti Foiskola, 2010. 215-223 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490071] 55. Budić, Ivan; Novoselović, Daniel; Bauer, Branko; Mance, Ines. Određivanje zaostalih naprezanja u rešetkastoj probi // 2nd International conference "VALLIS AUREA" 2010 / Katalinić, Branko (ur.). Požega - Vienna: Veleučilište u Požegi & DAAAM International Vienna, 2010. 0203-0209 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 481746] 56. Čičak, Mirjana; Dabić, Marina; Kiessling S. Timothy. Managerial tools & Internet the sources of competitive advantage of firms // 14th International Research/Expert Conference "Trends in the Development of Machinery and Associated Technology" TMT 2010 / Ekinović, Sabahudin; Uctug, Yildirim; Vivancos Calvet, Joan (ur.). Zenica, Bosna i Hercegovina: Faculty of Mechanical Engineering in Zenica; Escola Tecnica Superior D'Enginyeria Industrial de Barcelona, Universitat Politecnica de Catalunya, Spain; Bahcesehir University Istanbul, Muhendislik Fakultesi, Turkey, 2010. 209-212 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 487000] 57. Damjanović, Darko; Baškarić, Tomislav; Matejiček, Franjo; Kozak, Dražan; Ivandić, Željko. Stress analysis of long beam by theory of elasticity // Proceedings of the 2nd International Scientific and Expert Conference TEAM 2010 / Arpad, Ferencz ; Klebniczki Jozsef ; Lipoczine, Csabai; Borsne, Judit; Csaba, Fabian (ur.). Kecskemet: Kecskemeti Foiskola, 2010. 236-242 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490073] 162 ANNUAL REPORT 2010 58. Damjanović, Darko; Kozak, Dražan; Ivandić, Željko; Kokanović, Mato. Car design as new conceptual solution and CFD - analysis in purpose of improving aerodynamics // Proceedings of the FISITA 2010 World Automotive Congress. London: FISITA & GTE, 2010. (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 474541] Darko Damjanović at conference FISITA 2010 in Budapest 59. Fekete, Krešimir; Nikolovski, Srete; Knežević, Goran; Stojkov, Marinko; Kovač, Zoran. Simulation of Lightning Transients on 110 kV Overhead-Cable Transmission Line Using ATP-EMTP // Proceedings of the 15th IEEE Mediterranian Electromechanical Conference / Edward Gatt (ur.). Malta, 2010. 856-861 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 469978] 60. Galović, Antun; Virag, Zdravko; Živić, Marija; Holik, Mario. Eksergijska efikasnost procesa potpunog izgaranja zasićenih ugljikovodika // 8. skup o prirodnom plinu, toplini i vodi, 1. međunarodni skup o prirodnom plinu, toplini i vodi / Tonković, Zlatko ; Klarić, Štefanija ; Kozak, Dražan; Raos, Pero; Stojšić, Josip (ur.). Osijek, 2010. 03-1-03-10 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 486453] 61. Grizelj, Branko; Cumin, Josip; Šoškić, Nikola; Seuček, Ivan; Vujčić, Branimir. Utjecaj pravilnog izbora stroja i zagrijavanje materijala u oblikovanju metala deformiranjem na gospodarenje energijom i zaštitu okoliša // 8. Skup o prirodnom plinu, toplini i vodi 1. Međunarodni skup o prirodnom plinu, toplini i vodi / Tonković, Zlatko (ur.). Osijek: Strojarski fakultet, 2010. (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 485194] 62. Hadziahmetovic, Halima; Džaferović, Ejub; Čohodar, Maida; Klarić, Štefanija. System Of Fly Ash And Bottom Ash Transport From Thermal Power Plant // Proceedings of International Conference on Innovative Technologies INTECH / Kudlaček, Jan; Barisic, Branimir; Velay, Xavier; Ohkura, Kauhiro (ur.). Prag: Ing. Jan Kudlaček, 2010. 63-66 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 482746] 63. Holik, Mario; Kozak, Dražan; Konjatić, Pejo; Ivandić, Željko; Damjanović, Darko. Stress analysis of eave framework // Proceedings of the 2nd International Scientific and Expert Conference TEAM 2010 / Arpad, Ferencz; Klebniczki Jozsef; Lipoczine, Csabai; Borsne, Judit; Csaba, Fabian (ur.). Kecskemet: Kecskemeti Foiskola, 2010. 255260 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490075] 163 ANNUAL REPORT 2010 64. Hnatko, Emil; Lacković, Goran. Tromost podnog grijanja // Zbornik radova; Proceedings / Tonković, Zlatko (ur.). Osijek: Strojarski fakultet u Slavonskom Brodu, 2010. 23-123-9 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 498202] 65. Hnatko, Emil; Stojkov, Marinko; Kljajin, Milan; Hornung, Krunoslav. Ušteda prirodnog plina za grijanje uporabom sunčeve energije // Zbornik radova; Proceedings / Tonković Zlatko (ur.). Osijek: Strojarski fakultet u Slavonskom Brodu, 2010. 01-1-01-12 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 498237] 66. Karakašić, Mirko; Zadnik, Žiga; Kljajin, Milan; Duhovnik, Jožef. Design solutions with product function matrix and its requests // Proceedings of International Design Conference DESIGN 2010 / Marjanovic, Dorian (ur.). Zagreb: Fakultet strojarstva i brodogradnje Sveučilišta u Zagrebu, 2010. 821826 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 475006] 67. Katinić, Marko; Kozak, Dražan; Ivandić, Željko. Fracture of steam turbine rotor blades caused by corrosion fatigue - A case history // Proceedings of the 8th International Conference of the Carpathian Euro-Region Specialists in Industrial Systems / Ungureanu, Nicolae (ur.). Baia Mare: North University of Baia Mare, Faculty of Enginnering, 2010. 125-132 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 471364] 68. Kolesarić , Goran ; Đukić, Danijel; Lujić, Roberto. Rekonstrukcija sustava centralnog grijanja // 8th Natural Gas, Heat and Water Conference 1st International Natural Gas, Heat and Water Conference / Tonković, Zlatko; Klarić, Štefanija; Kozak, Dražan; Raos, Pero; Stojšić, Josip (ur.). Osijek: Strojarski fakultet u Slavonskom Brodu, 2010. (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 497668] 69. Koljenik, Antonio; Kozak, Dražan; Sertić, Josip; Matejiček, Franjo; Baličević, Pavo; Ivandić, Željko. Solving the differential equation bending of thin rectangular plates by finite difference method // Proceedings of the 2nd International Scientific and Expert Conference TEAM 2010 / Arpad, Ferencz; Klebniczki Jozsef; Lipoczine, Csabai; Borsne, Judit; Csaba, Fabian (ur.). Kecskemet: Kecskemeti Foiskola, 2010. 571-576 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490078] 164 The conference honorary committee (The 8th International Conference of the Carpathian Euro-Region Specialists in Industrial Systems, Baia Mare, Romania) ANNUAL REPORT 2010 70. Krumes, Dragomir; Kladarić, Ivica; Marušić, Vlatko; Stubičar, Mirko; Milinović, Andrijana; Mihailescu, Ion N. Influence of thermodiffusion treatments on improvement of surface layers properties created on low-carbon and lowalloyed steels // Proceedings of 14th International Research/Expert Conference "Trends in the Development of Machinery and Associated Technology" TMT 2010 / Ekinović, Sabahudin; Uctug, Yildirim; Vivancos Calvet, Joan (ur.). Zenica: Faculty of Mechanical Engineering in Zenica, Fakultetska 1, Zenica, BiH; Escola Technica Superior D'Enginyeria Industrial de Barcelona, Department d'Enginyeria Mechanica, Universitat politecnica de Catalunya, Spain; Bahcesehir university Istambul, Muhendislik Fakultesi, Turkey, 2010. 113-116 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 497820] Oral-presentation of dr. sc. Gordana Matičević at the conference TMT 2010 71. Marušić, Vlatko; Milinović, Andrijana; Galić Mladen. Mogućnost produljenja vijeka cijevi u kotlovima loženim komunalnim otpadom // Zbornik radova simpozija REUNION. Niška Banja, Srbija, 2010. (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 499549] 72. Marušić, Vlatko; Milinović, Andrijana; Galić, Josip. Neke mogućnosti smanjenja gubitaka kod pužnih preša velikog kapaciteta // Zbornik radova 51. savetovanje Proizvodnja i prerada uljarica / Savet tehnologa (ur.). Novi Sad: DOO "Industrijsko bilje" - Novi Sad; Tehnološki fakultet - Novi Sad; Tehnologija biljnih ulja i proteina; Institut za ratarstvo i povrtarstvo - Novi Sad, 2010. 111-117 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 496363] Poster-presentation at the conference TMT 2010 Prof. Sabahudin Ekinović, President of Organizing Committee of TMT 2010, with participants from MEFSB 73. Marušić, Vlatko; Milinović, Andrijana; Glavaš, Danko (Milivoj). Utjecaj parametara kaljenja na trošenje tribopara užnica/uže jaružara // Proceedings Book 10th International Foundrymen Conference Casting production / Unkić, Faruk (ur.). Sisak: Faculty of Metallurgy, University of Zagreb, 2010. 1-8 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 473831] 74. Matičević, Gordana; Dabić, Marina; Daim U. Tugrul. Using RFID for Real-Time Production Management in the Digital Enterprise // 14th International Research/Expert Conference "Trends in the Development of Machinery and Associated Technology" TMT 2010, Mediterranean Cruise, 11-18 September 2010 / Ekinović, Sabahudin; Uctug, Yildirim; Vivancos Calvet, Joan (ur.). Zenica, Bosna i Hercegovina: Faculty of Mechanical Engineering in Zenica; Escola Tecnica Superior D'Enginyeria Industrial de Barcelona, 165 ANNUAL REPORT 2010 Universitat Politecnica de Catalunya, Spain; Bahcesehir University Istanbul, Muhendislik Fakultesi, Turkey, 2010. 213-216 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 482667] 75. Miljković, Zvonko; Sporiš, Goran. Correlation Between the Indicators of Sitational Efficiency and Functionl Abilities of Football Players // 2nd International Conference" Vallis Aurea" Focus on: Regional Development / Katalinić Branko (ur.). Pozega: Veleučilište u Požegi, Hrvatska i DAAAM International Vienna, Austrija, 2010. 0929-0935 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 482126] 76. Nikolovski, Srete; Klaić, Zvonimir; Kraus, Zorislav; Stojkov, Marinko. Computation and measurement of electromagnetic fields in high voltage transformer substations // 33rd International Convention on Information and Communication Technology, Electronics and Microelectronics, Proceedings Vol. III Computers in Technical Systems & Intelligent Systems / Bogunović, Nikola; Ribarić, Slobodan (ur.). Rijeka: Croatian Society for Information and Communication Technology, Electronics and Microelectronics - MIPRO, 2010. 75-80 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 472453] 77. Raos, Pero; Stojšić, Josip; Somolanji, Marija. Izbor optimalnog postupka brze izradbe prototipova // Proceedings of the 2nd International Conference "Vallis Aurea" / Branko Katalinić (ur.). Požega: Polytechnic of Pozega & DAAAM International Vienna, 2010. 1229-1235 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 485133] 78. Samardžić, Ivan; Kozak, Dražan; Stoić, Antun; Ivandić, Željko; Dunđer Marko. Modern cost effective joining processes of thin wall materials // Proceedings of Manufacturing 2010, International Conference, Contemporary Problems of Manufacturing and Production Management, Poznan, Poland / dr. hab. inž. Roman Staniek (ur.). Poznan, Poland : Institute of Mechanical Technology, Poznan, Poland, (2010). 180-190 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 493489] 79. Stoić, Antun; Duspara, Miroslav; Stojšić, Josip. Technology approval of locomotive wheel production // Procedings of the 2nd international Scientific And Expert Conference TEAM 2010 / Árpád, Ferencz; József, Klebniczki; Sarolta, Csabai; Judit, Pető; Csaba, Fábián (ur.). KECSKEMÉT: KECSKEMÉT COLLEGE, 2010. 305-311 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 491220] 166 At the AMME 2010 (18th International Scientific Conference on Achievements in Mechanical and Materials Engineering, 13.-16.06.2010, Zakopane, Poland) Prof. dr. sc. Antun Stoić became a member of AMME World Academy ANNUAL REPORT 2010 80. Stoić, Antun; Raos, Pero; Duspara, Miroslav; Kladarić, Slavica. Smoothing of machined surfaces with roller burnishing tools // Proceedings of 7th Int. Conference on Mechanical Engineering GEPESZET 2010 / Stepan, Gabor (ur.). Budapest: Budapest: Budapest University of Tehnology and Economics, Faculty of Mechanical Engineering, 2010. 718-724 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 472471] 81. Šarić, Tomislav; Šimunović, Katica; Šimunović, Goran; Brckan, Krešimir; Brkanac, Krešimir. Održavanje poljoprivredne mehanizacije uz podršku informacijskih tehnologija // ODRŽAVANJE 2010 / MAINTENANCE 2010 / INSTANDHALTUNG 2010 / Čala, Ivo (ur.). Zagreb: Hrvatsko društvo održavatelja - HDO, 2010. 79-88 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 473257] 82. Šercer, Mladen; Raos, Pero; Rujnic-Sokele, Maja. Injection moulding and recycling of wood-thermoplastic composites // Proceedings of 7th Int. Conference on Mechanical Engineering GEPESZET 2010 / Stepan, Gabor (ur.). Budapest: Budapest University of Technoloy and Economics, Faculty of Mechanical Engineering, 2010. 908915 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 472469] Poster-presentation of Prof. dr. sc. Pero Raos at th the 7 International Conference on Mechanical Engineering GEPESZET 2010 in Budapest 84. Šercer, Mladen; Raos, Pero; Rujnić-Sokele, Maja. Thermal properties of bio- and synthetic based PUR foams // Proceedings - 13th ESAFORM Conference on Material Forming / Ceretti, Elisabetta; Giardini, Claudio (ur.). 2010. (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 469702] 85. Šercer, Mladen; Raos, Pero; Rujnić-Sokele, Maja. Thermal Properties of Common and Bio-Based Polyurethane // Proceedings of International Conference on Innovative Technologies IN-TECH / Kudlaček, Jan; Barisic, Branimir; Velay, Xavier; Ohkura, Kauhiro (ur.). Prag: World Association for Innovative Technologies and Center for Surface Treatement, 2010. 263-266 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 482742] 86. Šercer, Mladen; Tonković, Zlatko; Raos, Pero; Stojšić, Josip. Ispitivanje trajnosti membrana regulatora plina // Proceedings of 1st International natural gas, heat and water conference / Tonković, Zlatko; Klarić, Štefanija; Kozak, Dražan; Raos, Pero; Stojšić, Josip (ur.). Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 2010. 02-1-02-7 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 485142] 167 ANNUAL REPORT 2010 87. Šimunović, Goran; Čizmar, Atila; Šarić, Tomislav; Lujić, Roberto. Vrednovanje projekata distribucijskih plinovoda // Proceedings of 1st International conference of natural gas, heat and water conference / Tonković, Zlatko; Klarić, Štefanija; Kozak, Dražan; Raos, Pero; Stojšić, Josip (ur.). Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 2010. (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490804] 88. Šimunović, Goran; Lujić, Roberto; Šarić, Tomislav; Svalina, Ilija. Unaprjeđenje tehnološkog modula ERP sustava primjenom umjetne inteligencije // Proceedings of 1st International conference MTSM 2010 / Dražen, Živković (ur.). Split: Hrvatsko društvo za strojarske tehnologije, 2010. (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490793] 89. Šimunović, Katica; Štefanac, Miran; Šarić, Tomislav; Šimunović, Goran; Svalina, Ilija. Upravljanje materijalom u informacijskom sustavu MP2 Enterprise // Zbornik radova, Conference Proceedings MATRIB 2010 / Schauperl, Zdravko; Šnajdar, Mateja (ur.). Zagreb: Hrvatsko društvo za materijale i tribologiju, 2010. 426-435 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 474691] 90. Tonković, Zlatko; Raos, Pero; Somolanji, Marija. Analysis of the reliability of threated joints sealed with anaerobic polymeric sealants in gas pipeline installations // Procedings of the 2nd International Scientific And Expert Conference TEAM 2010 / Árpád, Ferencz; József, Klebniczki; Sarolta, Csabai; Judit, Pető; Csaba, Fábián (ur.). KECSKEMÉT: KECSKEMÉT COLLEGE, 2010. 318-324 (pos ter, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490382] 91. Tonković, Zlatko; Raos, Pero; Somolanji, Marija; Knežević, Pero. Utjecaj vremena zavarivanja i temperature okoline na svojstva elektrofuzijskog cijevnog zavara // Proceedings of 1st International natural gas, heat and water conference / Tonković, Zlatko; Klarić, Štefanija; Kozak, Dražan; Raos, Pero; Stojšić, Josip (ur.). Slavonski Brod : Strojarski fakultet u Slavonskom Brodu, 2010. 04-1-04-11 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 485151] 92. Tonković, Zlatko; Raos, Pero; Stojšić, Josip. Mathematical model for life prediction of damaged PE 80 gas pipes // Procedings of the 2nd International Scientific And Expert Conference TEAM 2010 / Árpád, Ferencz; József, Klebniczki; Sarolta, Csabai; Judit, Pető; Csaba, Fábián (ur.). KECSKEMÉT: KECSKEMÉT COLLEGE, 2010. 325-332 (poster, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490375] Prof. dr. sc. Katica Šimunović in front of the poster (conference MATRIB 2010, Vela Luka) 168 ANNUAL REPORT 2010 93. Tonković, Zlatko; Somolanji, Marija; Raos, Pero; Stojšić, Josip. Analiza rezultata modela za dnevno predviđanje potrošnje prirodnog plina // Proceedings of 2nd International Conference "Vallis Aurea" / Branko Katalinić (ur.). Požega: Polytechnic of Pozega & DAAAM International Vienna, 2010. 1451-1459 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 485138] Prof. dr. sc Goran Šimunović at the conference MTSM 2010 94. Vitez, Ivan; Krumes, Dragomir; Milinović, Andrijana. Čelici za poboljšavanje prema Europskim standardima // VIII Naučno/stručni simpozij sa međunarodnim učešćem "Metalni i nemetalni materijali" proizvodnja-osobineprimjena, Knjiga abstrakata sa elektronskim izdanjem Zbornika radova / Muhamedagić, Sulejman (ur.). Zenica, Bosna i Hercegovina: Univerzitet u Zenici, Organizaciona jedinica Fakulteta za metalurgiju i materijale, 2010. 166-171 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 469859] 95. Zmaić, Željko; Živić, Marija; Grgić Ivan. Numerical simulation of a flow and heat transfer in a waste incinerator // Proceedings of the 2nd International Scientific Conference TEAM 2010 / Arpad, Ferencz; Klebniczki Jozsef; Lipoczine, Csabai; Borsne, Judit; Csaba, Fabian (ur.). Kecskemet: Kecskemet College, 2010. 607-612 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490055] Participants (students and teachers of the MEFSB) at the conference MTSM 2010 96. Živi ć, Marija; Velji ć, Nataša; Jankovi ć, Zvonimir. Hydrodynamic analysis of a flow in water supply city network // Proceedings of the 2nd International Scientific and Expert Conference TEAM 2010 / Arpad, Ferencz; Klebniczki Jozsef; Lipoczine, Csabai; Borsne, Judit; Csaba, Fabian (ur.). Kecskemet: Kecskemet College, 2010. 601-606 (predavanje, međunarodna recenzija, objavljeni rad, znanstveni). [CROSBI-ID 490056] Other articles in conference proceedings with review: 97. Alinjak, Tomislav; Stojkov, Marinko; Jakšić, Dalibor. Program za proračun optimalne snage solarne elektrane priključene na distribucijsku mrežu s aspekta HEP-ODS-a // CIGRE, 9. simpozij o sustavu vođenja EES-a. 2010. (predavanje, domaća recenzija, objavljeni rad, stručni). [CROSBI-ID 498089] 98. Aračić, Stjepan; Prutki, Đurđica; Blažević, Marija; Matić, Dalibor. Analiza korozijske postojanosti jednoslojnog zaštitnog premaza // 19. savjetovanje o zaštiti materijala i industrijskom finišu (KOROMAT 2010): zbornik raadova / Vesna Alar, Vesna; Rajhenbah, Darko; Stojanović, Ivan (ur.). 169 ANNUAL REPORT 2010 Zagreb: Hrvatsko društvo za zaštitu materijala, 2010. 123132 (predavanje, domaća recenzija, objavljeni rad, stručni). [CROSBI-ID 469319] 99. Hadžiahmetović, Halima; Džaferović, Ejub; Klarić, Štefanija. Tehnički opis sustava za čišćenje cjevovoda u termoelektrani // Zbornik radova 8. Skup o prirodnom plinu, toplini i vodi / Tonković, Zlatko (ur.). Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 2010. 06-1-06-6 (poster, međunarodna recenzija, objavljeni rad, stručni). [CROSBI-ID 486985] 100. Jurakić, Bojan; Galeta, Tomislav; Užarević, Željko; Rondić, Miro. Izazovi izvedbenog projekta postrojenja za separaciju sirove nafte i plina // Zbornik radova / Z. Tonković, Š. Klarić, D. Kozak, P. Raso, J. Stojšić (ur.). Osijek: Strojarski fakultet u Slavonskom Brodu, 2010. 17-1-17-6 (predavanje, međunarodna recenzija, objavljeni rad, stručni). [CROSBIID 484786] 101. Kiš, Darko; Lacković, Ivica; Stoić, Antun. Selection of the firebox for burning straw from agriculture // Proceedings of the 1st International conference Sustainable Life in Manufacturing SLIM 2010 / Oguz Colak; Kopač, Janez (ur.). Isparta: Suleyman Demirel UNiversity CAD/CAM Research and Application Center & University of Ljubljana Faculty of Mechanical Engineering Laboratory for cutting, 2010. 128-131 (međunarodna recenzija, objavljeni rad, stručni). [CROSBI-ID 477603] 102. Kondić, Živko; Kondić, Veljko; Maglić, Leon. Integriranje metodologija lean i six sigma u metodologiju lean six sigma // 11. međunarodni Simpozij o kvaliteti Kvaliteta, konkuretnost i održivost / Drljača, Miroslav (ur.). Zagreb: OSKAR, 2010. 41-52 (predavanje, domaća recenzija, objavljeni rad, znanstveni). [CROSBI-ID 498198] 103. Kostelac Milan; Tepić Jovan; Kozak Dražan. Justification for Use of Tightening Elements in Joints Between the Wheel-Head and the Axle // Management of Technology Step to Sustainable Production / Ćosić, Predrag (ur.). Zagreb, 2010. No.: 272 (poster, međunarodna recenzija, objavljeni rad, stručni). [CROSBI-ID 477656] 104. Marušić, Vlatko; Todorić, Petar; Rosandić, Željko. Istraživanje mogućnosti smanjenja indirektnih triboloških gubitaka na pužnim prešama velikog kapaciteta // Conference proceedings MATRIB 2010 / Schauperl, Zdravko; Šnajdar, Mateja (ur.). Zagreb: HDMT Hrvatsko društvo za materijale i tribologiju, 2010. 306-313 (poster, domaća recenzija, objavljeni rad, stručni). [CROSBI-ID 476573] 170 ANNUAL REPORT 2010 105. Miljković, Zvonko; Sporiš, Goran. Sport Associations and Clubs as Incentive for Development and Enrichment of Student Life on the Universal Level of Education // 2nd Internation Conference "Vallis Aurea" Focus on: Regional Development / Katalinić Branko (ur.). Pozega: Veleučilište u Požegi, Hrvatska i DAAAM International Vienna, Austrija, 2010. 0937-0941 (predavanje, međunarodna recenzija, objavljeni rad, stručni). [CROSBI-ID 482125] 106. Raos, Pero; Stojšić, Josip; Somolanji, Marija. Smjese s metalnim punilom // 9. međunarodni simpozij Hrvatskog metalurškog društva "Materijali i metalurgija". (poster, međunarodna recenzija, objavljeni rad, stručni). [CROSBIID 477054] 107. Rosandić, Željko; Kladarić, Slavica; Marković, Radojka; Kladarić, Ivica; Samardžija, Darko. Utjecaj sastava konstrukcijskih čelika na prijelaznu temperaturu udarne žilavosti // 2nd International scientific and expert conference TEAM 2010 / Danyi, Jozsef (ur.). Kecskemet: Kecskemeti Foiskola, 2010. 292-296 (poster, međunarodna recenzija, objavljeni rad). [CROSBI-ID 490663] 108. Samardžić, Ivan; Kolumbić, Zvonimir; Stoić, Antun; Šoštarić, Damir; Bičvić, Davor. Parameters of fusion PE-HD pipes welding //8th Natural Gas, 1st International Natural Gas ; Heat and Water Conference, Osijek, Hrvatska, 29.0901.10.2010. (predavanje, međunarodna recenzija, objavljeni rad, stručni). [CROSBI-ID 482158] 109. Stoić, Antun; Samardžić, Ivan; Kozak, Dražan; Hloch, Sergej; Duspara, Miroslav. Modern high efficiency cutting processes // Proceedings of 7th International Conference on Mechanical Engineering (GEPESZET 2010) / Stepan, Gabor (ur.). Budapest: Budapest University of Tehnology and Economics, Faculty of Mechanical Engineering, 2010. 732-737 (poster, međunarodna recenzija, objavljeni rad, stručni). [CROSBI-ID 473489] 110. Katica Šimunović; Tomislav Draganjac; Roberto Lujić. Izbor dobavljača primjenom metode višekriterijskog odlučivanja // Conference Proceedings / Živković, Dražen (ur.). Split: Hrvatsko društvo za strojarske tehnologije, 2010. 20-30 (predavanje, međunarodna recenzija, objavljeni rad). [CROSBI-ID 490623] 111. Ugarković, Krešimir; Sokač, Davor; Sokodić, Željko; Boljevčan, Mirko; Klarić, Viktor; Stojkov, Marinko; Borovac, Marijana, Đaković, Sandra. Sanacija naponskih prilika u distribucijskoj mreži // Zbornik radova 2. savjetovanja, Hrvatski ogranak međunarodne elektrodistribucijske konferencije (CIRED) / mr. sc. Zdenko Tonković (ur.). Zagreb, 2010. 1-10 (predavanje, domaća recenzija, objavljeni rad, stručni). [CROSBI-ID 498508] 171 ANNUAL REPORT 2010 Abstracts in conference proceedings: 112. Aračić, Stjepan; Krumes, Dragomir; Vitez, Ivan. Tribocorrosion of low carbon steel C15E IN 5%NaCl and 5%NaCl + SiO2 // Sažeci predavanja s 9. međunarodnog simpozija Hrvatskog metalurškog društva SHMD '2010. "Materijali i metalurgija", tiskano u Metalurgija 49 (2010) 3 / Mamuzić, Ilija (ur.). Zagreb: Hrvatsko metalurško društvo, 2010. 200-200 (poster, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 493674] 113. Brazaluk, Iu. V.; Kochubey, O. O.; Vitez, Ivan; Polyakov, M. V.; Yevdokymov, D. V. Dissolution of discrete phase particles in liquid metal // Sažeci predavanja s 9. međunarodnog simpozija Hrvatskog metalurškog društva SHMD '2010. "Materijali i metalurgija", tiskano u Metalurgija 49 (2010) 3 / Mamuzić, Ilija (ur.). Zagreb: Hrvatsko metalurško društvo, 2010. 221-221 (poster, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 495025] 114. Budić, Ivan; Alar, Vesna; Esih, Ivan. Influence of chemical removal of oxide films, formed by exposure of high-alloy steel to air at high temperatures, on their pitting liability // "Eurocorr 2010" From the Earth´s Depths to Space Heights. Moskva, 2010. 525a (poster, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 482315] 115. Gigović-Gekić, A.; Oruč, M.; Vitez, Ivan. The effect of solution annealing on properties of steel Nitronic 60 // Sažeci predavanja s 9. međunarodnog simpozija Hrvatskog metalurškog društva SHMD '2010. "Materijali i metalurgija", tiskano u Metalurgija 49(2010)3 / Mamuzić, Ilija (ur.). Zagreb: Hrvatsko metalurško društvo, 2010. 196196 (poster, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 493649] 116. Klarić, Štefanija; Rosandić, Željko; Milinović, Andrijana. Examination of welding parameters influence on Stud Arc Welding process // Conference on Engineering research anniversary volume honoring Amalia and Miklos Ivany, Abstracts of the sixth international PhD & DLA symposium / Bachmann Balint, H. (ur.). Pecs: University of Pecs, Pollack Mihaly Faculty of Engineering, 2010. C:45-C:46 (predavanje, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 490606] 172 ANNUAL REPORT 2010 117. Kochubey, O. O.; Vitez, Ivan; Polyakov, M. V.; Serbichenko, D. M.; Yevdokymov, D. V. Austenite-martensite phase transition in cylindrical bodies // Sažeci predavanja s 9. međunarodnog simpozija Hrvatskog metalurškog društva SHMD '2010. "Materijali i metalurgija", tiskano u Metalurgija 49 (2010) 3 / Mamuzić, Ilija (ur.). Zagreb: Hrvatsko metalurško društvo, 2010. 199-200 (poster, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 493661] 118. Kochubey, O. O.; Vitez, Ivan, Yevdokymov, D.V. Numerical modeling of industrial soil pollution // Sažeci predavanja s 9. međunarodnog simpozija Hrvatskog metalurškog društva SHMD '2010. "Materijali i metalurgija", tiskano u Metalurgija 49 (2010) 3 / Mamuzić, Ilija (ur.). Zagreb: Hrvatsko metalurško društvo, 2010. 234-234 (poster, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 495037] 119. Marušić, V.; Vitez, Ivan; Stanić, D. The influence of composition of al alloy on properties of die casted engine components // Sažeci predavanja s 9. međunarodnog simpozija Hrvatskog metalurškog društva SHMD '2010. "Materijali i metalurgija", tiskano u Metalurgija 49 (2010) 3 / Mamuzić, Ilija (ur.). Zagreb: Hrvatsko metalurško društvo, 2010. 202-202 (poster, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 493675] 120. Pešić, Radivoje; Hnatko, Emil; Golec, Kazimierz; Đokić, Dragan; Veinović, Stevan. Transport ecology and anthropogenic global warming // Proceedings of Papers / Prof. dr. sc. Radonjić, D; Prof. dr. sc. Pešić, R. (ur.). Kragujevac: Mašinski fakultet u Kragujevcu, 2010. 501-510 (predavanje, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 498128] 121. Raos, Pero; Galeta, Tomislav. 3D Surface Models and Volume Rendering to Support Modern Head and Neck Pathology Diagnostic // Proceedings of 1st Croatian Rhinologis Congress. Zagreb: Croatian Society for Otorhinolaryngology and head and Neck Surgery, 2010. 7070 (pozvano predavanje, međunarodna recenzija, sažetak, znanstveni). [CROSBI-ID 445686] 173 ANNUAL REPORT 2010 Dissertations: 122. Karakašić, Mirko. Model povezivanja funkcija proizvoda, parametara i njihovih intervala vrijednosti kod razvoja proizvoda, primjenom matrice funkcije i funkcionalnosti / doktorska disertacija. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 12.03.2010., 187 str. Voditelj: Kljajin, Milan. [CROSBI-ID 457693] 123. Konjatić, Pejo. Analiza utjecaja geometrije zavara i mehaničkih svojstava materijala u zavaru na lomno ponašanje repariranog zavarenog spoja / doktorska disertacija. Slavonski Brod: Strojarski fakultet, 07.05.2010, 118 str. Voditelj: Matejiček, Franjo. [CROSBI-ID 486321] 124. Milinović, Andrijana. Istraživanje kinetike nastanka boridnih slojeva na nelegiranim čelicima / doktorska disertacija. Slavonski Brod: Strojarski fakultet, 14.07.2010., 108 str. Voditelj: Krumes, Dragomir. [CROSBI-ID 497437] 125. Novoselović, Daniel. Utjecaj tehnoloških parametara na zaostala naprezanja pri tlačnom lijevanju odljevaka / doktorska disertacija. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 16.07.2010., 109 str. Voditelj: Budić, Ivan. [CROSBI-ID 481743] Graduation theses: 126. Borjanić, Bojan. Utjecaj pripreme površine na postupak topilinskog naštrcavanja materijala / diplomski rad. Slavonski Brod: Strojarski fakultet, 09.07.2010 2010, 69 str. Voditelj:Aračić Stjepan. [CROSBI-ID 484764] 127. Brkanac, Matija. Analiza korektivnog i preventivnog održavanja poljoprivredne mehanizacije / diplomski rad. Osijek: Strojarski fakultet, 18.01. 2010, 57 str. Voditelj: Šarić, Tomislav. [CROSBI-ID 441305] 128. Bubenik, Karlo. Primjena virtualnog servera za upravljanje dokumentima / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 27. 9. 2010., 74 str. Voditelj: Galeta, Tomislav [CROSBI-ID 485026] 129. Drinić, Dalibor. Projektiranje tehnologije izrade zupčanika prema crtežu DD1 / diplomski rad. Slavonski Brod: Strojarski fakultet, 14.01. 2010, 62 str. Voditelj: Grizelj, Branko. [CROSBI-ID 440303] 130. Đaković, Domagoj. Priprema kataloga alata u CAM sustavu / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 21.05. 2010., 46 str. Voditelj: Šimunović, Goran. [CROSBI-ID 490778] 174 ANNUAL REPORT 2010 131. Filipović, Ivana. Projektiranje tehnologije izradbe nosača prema crtežu IF1 / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 25.03. 2010., 46 str. Voditelj: Grizelj, Branko. [CROSBI-ID 449776] 132. Grgi ć, Ivan. Numeri č ki model prijenosa topline kondukcijom i konvekcijom u ložištu spalionice smeća / diplomski rad. Slavonski Brod: Strojarski fakultet, 06.05. 2010., 65 str. Voditelj: Živić, Marija. [CROSBI-ID 470367] 133. Ibrić, Almir. Priprema i praćenje tehnološkog procesa izrade kočionog diska / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 12.07. 2010., 62 str. Voditelj: Šimunović, Goran. [CROSBI-ID 490771] 134. Jančić, Ivan. Priprema i praćenje proizvodnje građevinskog materijala / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 15.01. 2010., 80 str. Voditelj: Šimunović, Goran. [CROSBI-ID 440844] 135. Jerković, Ružica. Hidrodinamički proračun složene cijevne mreže / diplomski rad. Slavonski Brod: Strojarski fakultet, 14.1. 2010., 77 str. Voditelj: Živić, Marija. [CROSBI-ID 442797] 136. Jurakić, Bojan. Postupak oblikovanja cjevovoda naftnog postrojenja / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 27. 9. 2010., 76 str. Voditelj: Galeta, Tomislav [CROSBI-ID 485022] 137. Klaić, Igor. Rješenje problema transporta i manipulacije nabe u proizvodnom pogonu / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 08.06. 2010., 94 str. Voditelj: Kozak, Dražan. [CROSBI-ID 494651] 138. Ljevar, Marinko. Toplo oblikovanje plastomera / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 12.01. 2010., 78 str. Voditelj: Raos, Pero. [CROSBIID 440300] 139. Matić, Dalibor. Ekološki prihvatljivo održavanje organskih premaza na cestovnim objektima / diplomski rad. Slavonski Brod: Strojarski fakultet, 5.03.2010 2010, 78 str. Voditelj: Aračić Stjepan. [CROSBI-ID 469386] 140. Medaković, Mario. Ocijena vjerojatnosti korozijskih oštećenja u kotlovima / diplomski rad. Slavonski Brod: Strojarski fakultet, 29.09.2010. 2010, 63 str. Voditelj: Aračić Stjepan. [CROSBI-ID 485011] 175 ANNUAL REPORT 2010 141. Mihaljević, Damir. Projekt i konstrukcija kosilice za voćnjake / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 04.02. 2010., 71 str. Voditelj: Kljajin, Milan. [CROSBI-ID 458611] 142. Ožvat, Mirko. Tehnološka priprema u metaloprerađivačkom poduzeću / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 14.01. 2010., 67 str. Voditelj: Šimunović, Goran. [CROSBI-ID 440847] 143. Pandža, Robert. Projektiranje tehnologije izradbe poklopca za lampion / diplomski rad. Slavonski Brod: VUSB Tehnički odjel - stručni studij proizvodnog strojarstva, 18.03. 2010, 52 str. Voditelj: Grizelj, Branko. [CROSBI-ID 449704] 144. Perić, Saša. Planiranje i izrada membranskih zidova kotla / diplomski rad. Slavonski Brod: Strojarski fakultet, 15.01. 2010, 72 str. Voditelj: Lujić, Roberto. [CROSBI-ID 497765] 145. Pezer, Danijela. Projektiranje tehnologije izrade držača prema crtežu PD1 / diplomski rad. Slavonski Brod: Strojarski fakultet, 14.1.2010, 80 str. Voditelj: Grizelj, Branko. [CROSBI-ID 440297] 146. Ravančić, Damir. Informatička podrška u planiranju i praćenju remonta ventila u sekundarnom dijelu nuklearne elektrane / diplomski rad. Slavonski Brod: Strojarski fakultet, 15.01. 2010, 57 str. Voditelj: Lujić, Roberto. [CROSBI-ID 497764] 147. Ravlić, Anto. Analiza ekološke eksploatacije energetskog postrojenja / diplomski rad. Slavonski Brod: Strojarski fakultet, 29.09.2010. 2010, 97 str. Voditelj: Aračić, Stjepan. [CROSBI-ID 484999] 148. Šarek, Boris. Projektiranje tehnologije izrade posude prema crtežu BŠ1 / diplomski rad. Slavonski Brod: Strojarski fakultet, 14.1. 2010, 75 str. Voditelj: Grizelj, Branko. [CROSBI-ID 440290] 149. Šimić, Ivica. Informacijski sustavi proizvodnih poduzeća / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 08.07. 2010., 78 str. Voditelj: Šimunović, Goran. [CROSBI-ID 490777] 150. Šimunić, Slaven. Konstrukcijsko oblikovanje i proračun čvrstoće dijelova auto-dizalice Stenhøj Marshal 3000 / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 11.01. 2010., 61 str. Voditelj: Kozak, Dražan. [CROSBI-ID 460685] 176 ANNUAL REPORT 2010 151. Štefanac, Miran. Priprema materijala i tehnološka priprema za izradu vratila / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 05.03. 2010., 84 str. Voditelj: Šimunović, Katica. [CROSBI-ID 446858] 151. Tudić, Ivan. Tehnike rješavanja problema linearnog programiranja / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 08.07. 2010., 78 str. Voditelj: Šimunović, Katica. [CROSBI-ID 476317] 151. Ugarković, Josip. Odlučivanje o izboru polaznog materijala primjenom kvantitativnih metoda / diplomski rad. Slavonski Brod: Strojarski fakultet u Slavonskom Brodu, 08.07. 2010., 81 str. Voditelj: Šimunović, Katica. [CROSBI-ID 476318] 151. Zeba, Zoran. Projektiranje tehnologije izrade vilice prema crtežu ZZ1 / diplomski rad. Slavonski Brod: Strojarski fakultet, 14.01. 2010, 63 str. Voditelj: Grizelj, Branko. [CROSBI-ID 440286] 177 ANNUAL REPORT 2010 The Last Archived The first visit of delegation from the MEFSB to the Faculty of Materials Science and Technologies (TU Bratislava). Hosted by vice-dean Mr Peterka (27.11.2010) The MEFSB stand on the Fair of the University Constituents in Osijek (10.12.2010) 178 Trg I. B. Mažuranić 2 Slavonski Brod Gundulićeva 20 a Slavonski Brod Dr. Mile Budaka Slavonski Brod Trg I. B. Mažuranić 2 Slavonski Brod Gundulićeva 20 a Slavonski Brod Dr. Mile Budaka Slavonski Brod ANNUAL REPORT 2010 Texts & Photographs Darko Bobek, Ivan Budić, Darko Damjanović, Tea Duvnjak, Todor Ergić, Tomislav Galeta, Branko Grizelj, Emil Hnatko, Zvonimir Janković, Karolina Kamenski, Mirko Karakašić, Ivica Kladarić, Štefanija Klarić, Milan Kljajin, Pejo Konjatić, Dražan Kozak, Vlatko Marušić, Gordana Matičević, Andrijana Milinović, Danijel Novoselović, Pero Raos, Željka Rosandić, Željko Rosandić, Ivan Samardžić, Marija Somolanji, Antun Stoić, Marinko Stojkov, Josip Stojšić, Tomislav Šarić, Goran Šimunović, Katica Šimunović, Marija Živić. VONSK SLA IB D RO NICAL ENGIN HA IN G FACULT RIN Y EE ME C REPUBLIC of CROATIA
© Copyright 2024 Paperzz