SCHEDE PRODOTTO PANNELLI LED LP11-6060B45 Rexer LP11-6060B45 is a modern general lighting fixture producing high efficiency. Aesthetically pleasing diffused light with minimal glare, the ultra-thin panel can be fullfilled your ceiling space and installed easily in very shallow ceiling. High-powered white LEDs provide high CRI and energy efficient lighting for general lighting applications. Easy to install in the most common ceiling grids. ● Up to 80% energy saving compared to standard CFL ● Long lifetime of 40,000 hours ● Dimmable when using triac dimmer ● 120° wide beam angle ● 600x600mm cutout ● CCT: 4000K-4500K ● No UV/IR light ● Environment friendly, without Mercury or any other hazardous substances Application notes ● IP40 for indoor use only ● The lamp must be installed by professional electrician ● Ensure the power supply is switched off before fitting this product ● Do not touch the lamp when in use ● Keep away from hot steam and corrosive gas Application Areas ● General Lighting such as offices, hotels, home, shops, hospitals, schools ● Ceiling troffer fixtures 45W 2 PANNELLI LED Product Information 595 595 10 Technical Speci cations Voltage Power Power Factor Lumen (±5%) Beam angle CCT AC100-240V 45W ≥0.9 3200 120 o 4000K Model LP11-6060B45 Lifespan CRI 40000hs ≥80 Dimmable No Dimension 595*595*10mm Driver data Sheet Driver data Non-dim Input Voltage AC100-240V Frequency 50-60Hz Input rated Voltage AC100-240V E ciency ≥86% No load wattage ≤1W 45W±5 % Total load Wattage Power Factor ≥0.9 Rated input current ≤0.54A No load output Voltage DC45V No load output Voltage range DC35-50V Full load output Voltage DC34-37V Rated output current 1050mA Output current range 1050mA±5% Tolerance ±5% Current output tolerance ±5% Dimming range — Dimmer — Withstand voltage AC3750V Fixture Compatibility Rated Wattage 45W Electrical Classi cation II Ingress Protection (IP) 40 Operating Temp -10 oC-45 oC Operating Humidity 0-90% Storage Temp -20 oC-65 oC 3 PANNELLI LED Spectral Distribution LP11-6060B45 4000K 0.8 Max=7171 [1.0=20000] 2.12SDCM F4000K 0.7 Spectrum 0.6 0.5 x=0.3841 y=0.3816 0.4 0.3 0.2 0.1 0.0 380 500 600 Wavelength(nm) 700 800 Photometric Diagram LP11-6060B45 4000K Polar intensity diagram Cartesian intensity diagram Beam diagram Flux out: 2425 lm Planar Illuminance Curve -/+180 -120 120 E(LX) MH=10m 15 C0/180 C90/270 13.5 -90 0 90 3.281ft 1m 10.21ft 311.11cm 7.276 26.04fc 78.32, 280.3lx 20.41ft 622.22cm 3.234, 11.57fc 34.81, 124.6lx 30.62ft 933.32cm 1.819, 6.510fc 19.58, 70.08lx 40.83ft 1244.43cm 1.164, 4.167fc 12.53, 44.85lx 51.03ft 1555.54cm 12 6.562ft 300 29.11, 104.2fc 313.3, 1121lx 10.5 2m 9 600 9.843ft 7.5 900 3m 6 13.12ft 4.5 1200 4m 3 -30 1500 0 UNIT: cd AVERAGE BEAM ANGLE(50%): 114.6 DEG 4 30 1.5 0 16.4ft 5m -25 -20 -15 -10 -5 0 5 Distance(m) 10 15 20 25 Height Eavg, Emax Angle: 114.53deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at di erent distance. PANNELLI LED Polar Diagram Comparison +/-180 -150 O O 150 O -120 O 120 O 0 -90 O 90 O 300 UNIT: cd 600 900 -60 O C0/180, 114.5 deg 60 O C30/210, 114.3 deg 1200 C60/240, 114.8 deg 30 O 1500 -30 O 0O C90/270, 115.2 deg AVERAGE BEAM ANGLE (50%): 114.7DEG A Driver lifetime & LED lifetime LED Lifetime 90000 110% 0.0040 80000 105% 0.0035 70000 100% 0.0030 95% 0.0025 90% 0.0020 85% 0.0015 60000 % Luminous Flux Lifetime (hours) Driver Lifetime 50000 40000 30000 80% 20000 10000 75% 0 70% 65 oC 75 oC 85 oC 95 oC 105 oC FLUX 0.0010 0.0005 △ U'V' 0 1000 2000 3000 Capacitor TTc ( oC) 4000 5000 6000 7000 8000 9000 0.0000 10000 LifeTime (hours) T Temperature ● The testing is operated at 35°C environment temperature. ● The minimum lifetime for capacitor is 5000hours at 105°C, the lifetime f will be double when the temperature drop each 10°C ● Under 75°C working TEMP, P, max 40000hrs life time is achievable. P ● The highest withstand temperature of IC is 120°C ● The highest withstand temperature of MOS is 120°C The highest withstand LED junction temperature is 120°C 80 70 IC Capacitor 50 MOS 40 PCB 30 Fitting 20 Voltage transformer 10 Environmental temperature 8:20:16 7:29:16 6:38:16 5:47:16 4:56:16 3:14:16 4:05:16 2:23:16 1:32:16 0:41:16 23:50:16 22:59:16 22:08:16 21:17:16 20:26:16 19:35:16 18:44:16 17:53:16 17:02:16 16:11:16 14:29:22 0 15:20:16 TTemperature ( C) 60 o ● Time The driver lifespan is based on capacitor working temperature. 5 PANNELLI LED Installation 1.Recessed into ceiling 1. Move away ceiling plaster slab 2. Co Connect power supply 3. Fix the panel light to suitable place 4. Put the panel light steadily and then it can be used 2. Suspending 1. Fix the hook and screws to ceiling 2. Connect the steel wire rope to the panel light 3. Hanging the retaining rings on the hook, connect the power cord and then it can be used. Accessories (optionals) LP11-CC LP11-6060FR (silver or white colour) Packaging Information Carton 6 SIZE(CM) N.W/pc (KGS) 66.5*34.5*73 4.2 G.W.(KGS) W W.(KGS) Q'TY(PCS) 27.5 5 CTNS Q'TY(PCS) VOLUME(CBM) 20'' standard container 164 820 27.5 40'' standard container 330 1650 56 PANNELLI LED LPR01-24B18 Rexer UP-PL2419-15W is a modern general lighting fixture producing high efficiency. Aesthetically pleasing diffused light with minimal glare, the ultra-thin panel can be fullfilled your ceiling space and installed easily in very shallow ceiling. High-powered white LEDs provide high CRI and energy efficient lighting for general lighting applications. Easy to install in the most common ceiling grids. ● Up to 80% energy saving compared to standard CFL ● Long lifetime of 40,000 hours ● Dimmable when using triac dimmer ● 120° wide beam angle ● 230mm cutout ●CCT:4000K-4500K ● No UV/IR light ● Environment friendly, without Mercury or any other hazardous substances Application notes ● IP20 for indoor use ● The lamp must be installed by professional electrician ● Ensure the power supply is switched off before fitting this product ● Do not touch the lamp when in use ● Keep away from hot steam and corrosive gas Application Areas ● General Lighting such as offices , hotels, home, shops, hospitals, schools ● Ceiling troffer fixtures 18W 7 PANNELLI LED Product Information Ø240 Ø130 Ø220 19 Technical Speci cations Voltage Power Power Factor Lumen (±5%) Beam angle CCT UP-PL2419-15W AC100-240V 15W ≥0.9 870 120 o UP-PL2419-15W AC100-240V 15W ≥0.9 945 120 o Model Lifespan CRI Dimmable Dimension 3000K 40000hs ≥70 No Ø240*19mm cutout 230mm 4000K 40000hs ≥70 No Ø240*19mm cutout 230mm o UP-PL2419-15W AC100-240V 15W ≥0.9 1005 120 5000K 40000hs ≥70 No Ø240*19mm cutout 230mm UP-PL2419-15W AC100-240V 15W ≥0.9 1095 120 o 6000K 40000hs ≥70 No Ø240*19mm cutout 230mm o UP-PL2419-15W-D AC200-240V 15W ≥0.9 795 120 3000K 40000hs ≥70 Yes Ø240*19mm cutout 230mm UP-PL2419-15W-D AC200-240V 15W ≥0.9 855 120 o 4000K 40000hs ≥70 Yes Ø240*19mm cutout 230mm 915 120 o 5000K 40000hs ≥70 Yes Ø240*19mm cutout 230mm 120 o 6000K 40000hs ≥70 Yes Ø240*19mm cutout 230mm UP-PL2419-15W-D UP-PL2419-15W-D AC200-240V 15W AC200-240V 15W ≥0.9 ≥0.9 990 Driver data Sheet Driver data Input Voltage DIM Non-dim AC200-240V AC100-240V Frequency Input rated Voltage E ciency No load wattage Total load Wattage 50HZ 50-60HZ AC230V AC100-240V ≥78% ≥82% ≤1.2W ≤0.7W 15W±1W 15W±1W Power Factor Rated input current No load output Voltage ≥0.9 ≥0.9 ≤0.1A ≤0.18A DC32V DC32V No load output Voltage range DC28-36V DC28-36V Full load output Voltage DC17-20V DC17-20V Rated output current 630mA 670mA Output current range 630mA±5% 670mA±5% ±5% ±5% ±5% ±5% Tolerance Current output tolerance Dimming range Dimmer Withstand voltage 5%-10% — Triac dimmers — AC3750V AC3750V Fixture Compatibility Rated Wattage 15W 8 Electrical Classi cation II Ingress Protection (IP) 20 Operating Temp -10 oC-45 oC Operating Humidity 0-90% Storage Temp -20 oC-65 oC PANNELLI LED Spectral Distribution LPR01-24B18 4000K Max=7572 [1.0=20000] 0.8 19.15SDCM F5000K 0.7 Spectrum 0.6 0.5 x=0.3810 y=0.3893 0.4 0.3 0.2 0.1 0.0 380 500 600 Wavelength(nm) 700 800 Photometric Diagram LPR01-24B18 4000K Polar intensity diagram Cartesian intensity diagram Beam diagram Flux out: 926.4 lm Planar Illuminance Curve -/+180 -120 120 E(LX) MH=10m 5 C0/180 C90/270 4.5 -90 0 90 3.281ft 1m 9.666ft 294.62cm 3.116, 10.51fc 33.54, 113.1lx 19.33ft 589.23cm 1.385, 4.669fc 14.91, 50.26lx 29ft 883.85cm 0.7790, 2.626fc 8.385, 28.27lx 38.66ft 1178.47cm 0.4986, 1.681fc 5.366, 18.09lx 48.33ft 1473.09cm 4 6.562ft 100 12.46, 42.02fc 134.2, 452.3lx 3.5 2m 3 200 9.843ft 2.5 300 3m 2 13.12ft 1.5 400 4m 1 -30 500 0 UNIT: cd AVERAGE BEAM ANGLE(50%): 111.9 DEG 30 0.5 0 16.4ft 5m -25 -20 -15 -10 -5 0 5 Distance(m) 10 15 20 25 Height Eavg, Emax Angle: 111.66deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at di erent distance. 9 PANNELLI LED Polar Diagram Comparison +/-180 -150 O O 150 O -120 O 120 O 0 -90 O 90 O 100 UNIT: cd 200 300 -60 O C0/180, 111.2 deg 60 O C30/210, 110.9 deg 400 C60/240, 111.9 deg 30 O 500 -30 O 0O C90/270, 111.3 deg AVERAGE BEAM ANGLE (50%): 111.1DEG A Driver lifetime & LED lifetime LED Lifetime 90000 110% 0.0040 80000 105% 0.0035 70000 100% 0.0030 95% 0.0025 90% 0.0020 85% 0.0015 60000 % Luminous Flux Lifetime (hours) Driver Lifetime 50000 40000 30000 80% 20000 10000 75% 0 70% 65 oC 75 oC 85 oC 95 oC 105 oC FLUX 0.0005 △ U'V' 0 1000 2000 3000 Capacitor TTc ( oC) 4000 5000 6000 7000 8000 9000 LifeTime (hours) T Temperature ● The testing is operated at 35°C environment temperature. ● The minimum lifetime for capacitor is 5000hours at 105°C, the lifetime f will be double when the temperature drop each 10°C ● Under 75°C working TEMP, P, max 40000hrs life time is achievable. P ● The highest withstand temperature of IC is 120°C ● The highest withstand temperature of MOS is 120°C ● The highest withstand LED junction temperature is 120°C 80 70 IC o TTemperature ( C) 60 Capactior 50 MOS 40 PCB 30 Fitting 20 Voltage transformer 10 Environmental temperature 8:20:16 7:29:16 5:47:16 6:38:16 4:56:16 4:05:16 3:14:16 2:23:16 1:32:16 0:41:16 23:50:16 22:59:16 22:08:16 21:17:16 20:26:16 19:35:16 18:44:16 17:53:16 17:02:16 16:11:16 14:29:22 15:20:16 0 Time The driver lifespan is based on capacitor working temperature. 10 0.0010 0.0000 10000 PANNELLI LED Installation Install requirements Building element above tting A-gap above the top of the tting 25mm B-side gap to the structual membrane 25mm C-gap between thermal insulation 25mm Building structural membrance Thermal insulation Ceiling opening ¢230mm Connection Power 1 Latch Catch 2 Latch Catch Ceiling A. Vertical pull Latch B. Fasten the latch on the ceiling 3 4 Packaging Information SIZE(CM) Carton 52.5*37*29.5 N.W/pc (KGS) 0.75 G.W.(KGS) 12.5 CTNS Q'TY(PCS) 20'' standard container 480 4800 28 40'' standard container 965 9650 56 Q'TY(PCS) 10 VOLUME(CBM) 11 PANNELLI LED LT80-060B10 LT80-120B20 LT80-150B25 10W 20W 30W Rexer LED T8 tube integrates 2835SMD light source and a compact high efficiency driver into a traditional tube replacement. It employs a high-tech IC solution to ensure the good stability. The 6063 aluminium heat sink guarantees good heat dissipation. One-end power design for safe installation. ● Up to 70% energy saving compared to traditional tube ● Long lifetime of 40,000 hours ● 120° wide beam angle ● 600mm length ● CCT: 4000K-4500K ● No UV/IR light ● Environment friendly, without Mercury or any other hazardous substances Application notes ● ● ● ● ● 12 10W IP20 for indoor use only The lamp must be installed by professional electrician Turn off before installation, in case of electronic shock Do not touch the lamp when in use Keep away from hot steam and corrosive gas 20W 25W PANNELLI LED 605 / 1213 / 1513 28.5 590 / 1198 / 1498 32.3 Technical Speci cations Voltage Power Power Factor Lumen (±5%) Beam angle CCT AC100-240V 10W ≥0.9 940 120 o o Model UP-T810W600-H UP-T820W1200-H AC100-240V UP-T825W1500-H 20W AC100-240V 25W ≥0.9 ≥0.9 1880 120 120 o 2500 Lifespan CRI 4000K 40000hs ≥70 4000K 40000hs ≥70 No L1213*W28.5*H32.3mm 40000hs ≥70 No L1513*W28.5*H32.3mm 4000K Dimmable No Dimension L605*W28.5*H32.3mm Driver data Sheet Non-dim Non-dim Non-dim AC100-240V AC100-240V AC100-240V Frequency 50-60HZ 50HZ 50-60Hz Input rated Voltage AC230V AC230V AC230V E ciency ≥85% ≥89% ≥88% No load wattage ≤1W ≤1W ≤1W 10W±1W 20W±1W 25W±5% ≥0.9 ≥0.9 ≥0.9 Rated input current ≤0.13A ≤0.11A ≤0.28A No load output Voltage DC85V DC80V DC80V No load output Voltage range DC80-100V DC80-90V DC70-90V Full load output Voltage DC65-70V DC70-76V DC71-74V Rated output current 130mA 240mA 300mA Output current range 130mA±5% 240mA±5% 300mA±5% Tolerance ±5% ±5% ±5% Current output tolerance ±5% ±5% ±5% AC1500V AC1500V AC3750V Driver data Input Voltage Total load Wattage Power Factor Withstand voltage Fixture Compatibility Rated Wattage Electrical Classi cation Ingress Protection (IP) Operating Temp Operating Humidity Storage Temp 10W II 20 -10 oC-45 oC 0-90% -20 oC-65 oC 20W II 20 -10 oC-45 oC 0-90% -20 oC-65 oC 25W II 20 -10 C-45 C 0-90% -20 C-65 C 13 PANNELLI LED LT80-120B20 4000K LT80-060B10 4000K Max=6400 [1.0=20000] 0.8 2.16SDCM F4000K 0.7 0.7 0.6 0.6 0.5 x=0.3798 y=0.3756 0.4 Max=4914 [1.0=20000] 2.51SDCM F4000K 0.5 Spectrum Spectrum 0.8 x=0.3788 y=0.3742 0.4 0.3 0.3 0.2 0.2 0.1 0.1 0.0 0.0 500 380 600 Wavelength(nm) 700 380 800 500 600 Wavelength(nm) 700 800 LT80-150B25 4000K Max=6227 [1.0=20000] 0.8 5.98SDCM F4000K 0.7 Spectrum 0.6 0.5 x=0.3755 y=0.3653 0.4 0.3 0.2 0.1 0.0 380 500 600 Wavelength(nm) 700 800 Photometric Diagram LT80-120B20 4000K LT80-060B10 4000K Polar intensity diagram Cartesian intensity diagram Polar intensity diagram Beam diagram Cartesian intensity diagram Beam diagram Flux out: 1027 lm Flux out: 550.4 lm Planar Illuminance Curve -/+180 120 -120 E(LX) MH=10m 3 C0/180 C90/270 2.7 -90 0 90 -120 3.281ft 1m 7.979, 25.12fc 85.89, 270.4lx 120 2m 1.995, 6.281fc 21.47, 67.60lx 18.08ft 550.99cm 0.8866, 2.791fc 9.543, 30.05lx 27.12ft 826.48cm 1.5 180 3m 110 0.9 4m 0.4987, 1.570fc 5.368, 16.90lx -30 0 UNIT: cd AVERAGE BEAM ANGLE(50%): 120.7 DEG 30 2m 2.75 36.15ft 1101.97cm 9.169ft 279.48cm 3.722, 11.63fc 40.06, 125.2lx 18.34ft 558.95cm 1.654, 5.168fc 17.81, 55.63lx 3m 27.51ft 838.43cm 0.9305, 2.907fc 10.02, 31.29lx 36.68ft 1117.91cm 2.2 13.12ft 1.65 440 4m 16.4ft 5m -25 -20 -15 -10 -5 0 5 10 15 20 25 Distance(m) Height -30 45.19ft 1377.47cm 0.3192, 1.005fc 3.436, 10.82lx Eavg, Emax Angle: 108.04deg 550 30 0 UNIT: cd AVERAGE BEAM ANGLE(50%): 121.0 DEG Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at di erent distance. 0.55 0 16.4ft 5m -25 -20 -15 -10 Polar intensity diagram Cartesian intensity diagram Beam diagram Flux out: 578.1 lm Planar Illuminance Curve -/+180 -120 120 E(LX) MH=10m 3 C0/180 C90/270 2.7 -90 0 90 3.281ft 1m 8.382, 26.06fc 90.22, 280.5lx 9.244ft 281.76cm 2.4 6.562ft 60 2.1 2m 2.095, 6.516fc 22.55, 70.14lx 18.49ft 563.51cm 0.9313, 2.896fc 10.02, 31.17lx 27.73ft 845.27cm 0.5239, 1.629fc 5.639, 17.53lx 36.98ft 1127.03cm 1.8 120 9.843ft 1.5 180 3m 1.2 13.12ft 0.9 240 4m 0.6 -30 300 0 UNIT: cd AVERAGE BEAM ANGLE(50%): 122.8 DEG 30 0.3 0 16.4ft 5m -25 -20 -15 -10 -5 0 5 Distance(m) 10 15 20 25 Height 0.3353, 1.043fc 3.609, 11.22lx Eavg, Emax 46.22ft 1408.78cm Angle: 109.26deg -5 0 5 Distance(m) LT80-150B25 4000K 14 14.89, 46.61fc 160.3, 500.7lx 1.1 0.3 0 1m 9.843ft 0.6 300 3.281ft 3.3 330 13.12ft C0/180 C90/270 4.4 3.85 220 1.2 240 90 6.562ft 1.8 9.843ft MH=10m 4.95 0 -90 2.1 120 E(LX) 5.5 9.039ft 275.49cm 2.4 6.562ft 60 Planar Illuminance Curve -/+180 Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance. 10 15 20 25 Height 45.85ft 1397.38cm 0.5955, 1.861fc 6.410, 20.03lx Eavg, Emax Angle: 108.82deg Diameter Note: The Curves indicate the illuminated area and the average illumination when the Luminaire is at different distance. PANNELLI LED Installation 1. One end power tube,installation with Electric Ballast G13 Lamp holder G13 Lamp holder G13 Lamp holder G13 Lamp holder G13 Lamp holder G13 Lamp holder Fluorescent tube Fluorescent tube LED light tube Disconnect the wire 100-240VAC 100-240VAC Junction Box Electric Ballast 100-240VAC Junction Box Electric Ballast Step 1 Junction Box Step 2 Step 3 2. One end power tube,installation with Inductive Ballast Junction Box Junction Box Inductive Ballast Remove the inductive ballast or not (In order to save more energy, plese remove ballast) Connect the wire if the inductive ballast is removed Junction Box 100-240VAC 100-240VAC 100-240VAC G13 Lamp holder G13 Lamp holder G13 Lamp holder G13 Lamp holder G13 Lamp holder G13 Lamp holder Fluorescent tube LED light tube Fluorescent tube Fluorescent starter Install the LED tube and dummy starter Remove the Fluorescent starter Step 1 Step 2 Step 3 3. Two end power tube, installation with Electric Ballast G13 Lamp holder G13 Lamp holder G13 Lamp holder G13 Lamp holder Fluorescent tube G13 Lamp holder G13 Lamp holder LED light tube Fluorescent tube Disconnect the wire 100-240VAC 100-240VAC Junction Box 100-240VAC Junction Box Electric Ballast Junction Box Electric Ballast Step 1 Step 2 Step 3 4. Two end power tube, installation with Inductive Ballast Junction Box Remove the inductive ballast or not (In order to save more energy, plese remove ballast) Junction Box Inductive Ballast Connect the wire if the inductive ballast is removed 100-240VAC Junction Box 100-240VAC G13 Lamp holder G13 Lamp holder G13 Lamp holder G13 Lamp holder 100-240VAC Fluorescent tube G13 Lamp holder Fluorescent tube G13 Lamp holder LED light tube Fluorescent starter Remove the Fluorescent starter Step 1 Step 2 Step 3 Packaging Information SIZE(CM) Carton 129.5*22*23.5 N.W/pc (KGS) 0.31 G.W.(KGS) 16.7 CTNS Q'TY(PCS) 20'' standard container 415 10375 28 40'' standard container 830 20750 56 Q'TY(PCS) 25 VOLUME(CBM) 15 LED STRIP 3014 LED flexible strips 30 LEDs al metro Bobina da 5m -150 LEDs LS3014-030-24B 4000K LUCE NATURALE LS3014-030-24F 6000K LUCE FREDDA LS3014-030-24C 3000K LUCE CALDA CARATTERISTICHE: Durata del LED: 50,000 ore Tagliabile ogni 6 LED seguendo le linee di taglio Nastro flessibile per formare linee curve Basso consumo SPECIFICHE TECNICHE: Colore disponibile del LED: 4000K, 3000K, 6000K CRI: ≥80 Tipo di LED: 3014 SMD LED Numero di LED: 150 LEDs/5 metri (30 LEDs al metro) Dimensioni: L 5000mm (5m) x W 8mm x T 3.5mm Packaging: Bobina da 5 metri View angle:120° Working Input Voltage: 24VDC Working Current/meter: 0.625A/5 metri Output power: 3W al metro (15W /5 metri) Flusso luminoso: 10-12 Lumens/LED Temperatura di esercizio: -20° to 50° PCB color: bianco con nastro autoadesivo 3M sul retro non-waterproof IP20 Dimensioni imballato: 31x47x28 cm. INNER: cartoni da 10 rotoli MASTER: 5 16 3W al metro LED STRIP 3014 LED flexible strips 60 LEDs al metro Bobina da 5m - 300 LEDs LS3014-060-24B 4000K LUCE NATURALE LS3014-060-24F 6000K LUCE FREDDA LS3014-060-24C 3000K LUCE CALDA CARATTERISTICHE: Durata del LED: 50,000 ore Tagliabile ogni 6 LED seguendo le linee di taglio Nastro flessibile per formare linee curve Basso consumo SPECIFICHE TECNICHE: Colore disponibile del LED: 4000K, 3000K, 6000K CRI: ≥80 Tipo di LED: 3014 SMD LED Numero di LED: 300 LEDs/5 metri (60 LEDs al metro) Dimensioni: L 5000mm (5m) x W 8mm x T 3.5mm Packaging: Bobina da 5 metri View angle:120° Working Input Voltage: 24VDC Working Current/meter: 1.25A/5 metri Output power: 6W al metro (30W /5 metri) Flusso luminoso: 10-12 Lumens/LED Temperatura di esercizio: -20° to 50° PCB color: bianco con nastro autoadesivo 3M sul retro non-waterproof IP20 Dimensioni imballato: 31x47x28 cm. INNER: cartoni da 10 rotoli MASTER: 5 6W al metro 17 LED STRIP 3014 LED flexible strips 120 LEDs al metro Bobina da 5m -150 LEDs LS3014-120-24B 4000K LUCE NATURALE LS3014-120-24F 6000K LUCE FREDDA LS3014-120-24C 3000K LUCE CALDA CARATTERISTICHE: Durata del LED: 50,000 ore Tagliabile ogni 6 LED seguendo le linee di taglio Nastro flessibile per formare linee curve Basso consumo SPECIFICHE TECNICHE: Colore disponibile del LED: 4000K, 3000K, 6000K CRI: ≥80 Tipo di LED: 3014 SMD LED Numero di LED: 600 LEDs/5 metri (120 LEDs al metro) Dimensioni: L 5000mm (5m) x W 8mm x T 3.5mm Packaging: Bobina da 5 metri View angle:120° Working Input Voltage: 24VDC Working Current/meter: 2.5A/5 metri Output power: 12W al metro (60W /5 metri) Flusso luminoso: 10-12 Lumens/LED Temperatura di esercizio: -20° to 50° PCB color: bianco con nastro autoadesivo 3M sul retro non-waterproof IP20 Dimensioni imballato: 31x47x28 cm. INNER: cartoni da 10 rotoli MASTER: 5 18 12W al metro LED STRIP 3014 LED flexible strips 240 LEDs al metro Bobina da 5m -1200 LEDs LS3014-240-24B 4000K LUCE NATURALE LS3014-240-24F 6000K LUCE FREDDA LS3014-240-24C 3000K LUCE CALDA CARATTERISTICHE: Durata del LED: 50,000 ore Tagliabile ogni 6 LED seguendo le linee di taglio Nastro flessibile per formare linee curve Basso consumo SPECIFICHE TECNICHE: Colore disponibile del LED: 4000K, 3000K, 6000K CRI: ≥80 Tipo di LED: 3014 SMD LED Numero di LED: 1200 LEDs/5 metri (240 LEDs al metro) Dimensioni: L 5000mm (5m) x W 8mm x T 3.5mm Packaging: Bobina da 5 metri View angle:120° Working Input Voltage: 24VDC Working Current/meter: 5A/5 metri Output power: 24W al metro (120W /5 metri) Flusso luminoso: 10-12 Lumens/LED Temperatura di esercizio: -20° to 50° PCB color: bianco con nastro autoadesivo 3M sul retro non-waterproof IP20 Dimensioni imballato: 31x47x28 cm. INNER: cartoni da 10 rotoli MASTER: 5 24W al metro 19 LED STRIP 3528 LED flexible strips 240 LEDs al metro Bobina da 5m -1200 LEDs LS3528-240-24B 4000K LUCE NATURALE LS3528-240-24F 6000K LUCE FREDDA LS3528-240-24C 3000K LUCE CALDA CARATTERISTICHE: Durata del LED: 50,000 ore Tagliabile ogni 6 LED seguendo le linee di taglio Nastro flessibile per formare linee curve Basso consumo SPECIFICHE TECNICHE: Colore disponibile del LED: 4000K, 3000K, 6000K CRI: ≥80 Tipo di LED: 3528 SMD LED Numero di LED: 1200 LEDs/5 metri (240 LEDs al metro) Dimensioni: L 5000mm (5m) x W 8mm x T 3.5mm Packaging: Bobina da 5 metri View angle:120° Working Input Voltage: 24VDC Working Current/meter: 4A/5 metri Output power: 19.2W al metro (96W /5 metri) Flusso luminoso: 6-7 Lumens/LED Temperatura di esercizio: -20° to 50° PCB color: bianco con nastro autoadesivo 3M sul retro non-waterproof IP20 Dimensioni imballato: 31x47x28 cm. INNER: cartoni da 10 rotoli MASTER: 5 20 19.2W al metro LED STRIP 5630 LED flexible strips 72 LEDs al metro Bobina da 5m - 360 LEDs LS5630-072-24B 4000K LUCE NATURALE LS5630-072-24F 6000K LUCE FREDDA LS5630-072-24C 3000K LUCE CALDA CARATTERISTICHE: Durata del LED: 50,000 ore Tagliabile ogni 6 LED seguendo le linee di taglio Nastro flessibile per formare linee curve Basso consumo SPECIFICHE TECNICHE: Colore disponibile del LED: 4000K, 3000K, 6000K CRI: ≥80 Tipo di LED: 5630 SMD LED Numero di LED: 360 LEDs/5 metri (72 LEDs al metro) Dimensioni: L 5000mm (5m) x W 8mm x T 3.5mm Packaging: Bobina da 5 metri View angle:120° Working Input Voltage: 24VDC Working Current/meter: 7.5A/5 metri Output power: 24W al metro (120W /5 metri) Flusso luminoso: 45-50 Lumens/LED Temperatura di esercizio: -20° to 50° PCB color: bianco con nastro autoadesivo 3M sul retro non-waterproof IP20 Dimensioni imballato: 31x47x28 cm. INNER: cartoni da 10 rotoli MASTER: 5 24W al metro 21
© Copyright 2024 Paperzz
