DSC-W110/W115
SERVICE MANUAL
LEVEL
2
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
Korea Model
Argentine Model
Brazilian Model
Thai Model
Japanese Model
Ver. 1.1 2008.05
Revision History
Internal memory
ON BOARD
Revised-1
Replace the previously issued
SERVICE MANUAL 9-852-298-31
with this manual.
Photo: DSC-W110/Silver
Link
SPECIFICATIONS
DISASSEMBLY
SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAM
REPAIR PARTS LIST
• Precaution on Replacing the SY-188 Board
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DIGITAL STILL CAMERA
DSC-W110/W115_L2
9-852-298-32
Sony EMCS Co.
2008E0500-1
© 2008.5
Published by Kohda TEC
SPECIFICATIONS
Camera
[Input and Output connectors]
[System]
Multi connector: Video output
Audio output (Monaural)
USB communication
USB communication: Hi-Speed USB (USB 2.0
compliant)
Image device:
7.20 mm (1/2.5 type) color CCD, Primary
color filter
Total pixel number of camera:
Approx. 7.4 Megapixels
Effective pixel number of camera:
Approx. 7.2 Megapixels
Lens: Carl Zeiss Vario-Tessar 4× zoom lens
f = 5.35 – 21.4 mm (32 – 128 mm (35 mm
film equivalent)) F2.8 (W) – F5.8 (T)
Exposure control: Automatic exposure, Scene
Selection (9 modes)
White balance: Automatic, Daylight, Cloudy,
Fluorescent 1,2,3, Incandescent, Flash
File format (DCF compliant):
Still images: Exif Ver. 2.21 JPEG compliant,
DPOF compatible
Movies: MPEG1 compliant (Monaural)
Recording media: Internal Memory (approx.
15 MB), “Memory Stick Duo”
Flash: Flash range (ISO sensitivity
(Recommended exposure Index) set to Auto):
Approx. 0.2 to 3.9 m (7 7/8 inches to 12 feet
9 5/8 inches) (W)/approx. 0.5 to 1.9 m (1 feet
7 3/4 inches to 6 feet 2 7/8 inches) (T)
[LCD screen]
LCD panel: 6.2 cm (2.5 type) TFT drive
Total number of dots: 115 200 (480 × 240) dots
[Power, general]
Power: Rechargeable battery pack
NP-BG1, 3.6 V
NP-FG1 (not supplied), 3.6 V
AC-LS5K AC Adaptor (not supplied), 4.2 V
Power consumption (during shooting, LCD screen on):
0.9 W
Operating temperature: 0 to 40°C (32 to 104°F)
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions:
88.2 × 57.2 × 22.9 mm (3 1/2 × 2 3/8 ×
29/32 inches) (W/H/D, excluding protrusions)
Mass:
Approx. 156 g (5.5 oz) (including NP-BG1
battery pack, strap, etc.)
Microphone: Monaural
Speaker: Monaural
Exif Print: Compatible
PRINT Image Matching III: Compatible
PictBridge: Compatible
DSC-W110/W115_L2
—2—
BC-CSGB/BC-CSGC battery
charger
Power requirements: AC 100 V to 240 V, 50/60 Hz,
2.6 W (BC-CSGB), 2 W (BC-CSGC)
Output voltage: DC 4.2 V, 0.25 A
Operating temperature: 0 to 40°C (32 to 104°F)
Storage temperature: –20 to +60°C (–4 to +140°F)
Dimensions: Approx. 62 × 24 × 91 mm (2 1/2 ×
31/32 × 3 5/8 inches) (W/H/D)
Mass: Approx. 75 g (2.7 oz)
Rechargeable battery pack NP-BG1
Used battery: Lithium-ion battery
Maximum voltage: DC 4.2 V
Nominal voltage: DC 3.6 V
Capacity: 3.4 Wh (960 mAh)
Design and specifications are subject to change
without notice.
Ver. 1.1 2008.05
The changed portions from
Ver. 1.0 are shown in blue.
Model information table
Model
Destination
DSC-W110
DSC-W115
US, CND, AEP, UK,
E, AUS, CH, KR,
AR, BR, TH, J
CND, AEP, UK, AR
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
TH : Thai model
DSC-W110/W115_L2
—3—
ENGLISH
JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
DSC-W110/W115_L2
—4—
ENGLISH
JAPANESE
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
サービス，点検時には次のことにご注意下さい。
1. 注意事項をお守りください。
サービスのとき特に注意を要する個所については，
キャビネット，シャーシ，部品などにラベルや捺印で
注意事項を表示しています。これらの注意書き及び取
扱説明書等の注意事項を必ずお守り下さい。
2. 指定部品のご使用を
セットの部品は難燃性や耐電圧など安全上の特性を
持ったものとなっています。従って交換部品は，使用
されていたものと同じ特性の部品を使用して下さい。
特に回路図，部品表に0印で指定されている安全上重要
な部品は必ず指定のものをご使用下さい。
3. 部品の取付けや配線の引きまわしはもとどおりに
安全上，チューブやテープなどの絶縁材料を使用した
り，プリント基板から浮かして取付けた部品がありま
す。また内部配線は引きまわしやクランパによって発
熱部品や高圧部品に接近しないよう配慮されています
ので，これらは必ずもとどおりにして下さい。
4. サービス後は安全点検を
サービスのために取外したネジ，部品，配線がもとど
おりになっているか，またサービスした個所の周辺を
劣化させてしまったところがないかなどを点検し，安
全性が確保されていることを確認して下さい。
5. チップ部品交換時の注意
• 取外した部品は再使用しないで下さい。
• タンタルコンデンサのマイナス側は熱に弱いため交
換時は注意して下さい。
6. フレキシブルプリント基板の取扱いについて
• コテ先温度を270℃前後にして行なって下さい。
• 同一パターンに何度もコテ先を当てないで下さい。
（3回以内）
• パターンに力が加わらないよう注意して下さい。
7. 無鉛半田について
無鉛半田を使用している基板には，無鉛（Lead Free）を意
味するレッドフリーマークがプリントされています。
（注意：基板サイズによっては，無鉛半田を使用して
いてもレッドフリーマークがプリントされて
いないものがあります）
：レッドフリーマーク
無鉛半田には，以下の特性があります。
• 融点が従来の半田よりも約40℃高い。
従来の半田こてをそのまま使用することは可能です
が，少し長めにこてを当てる必要があります。
温度調節機能のついた半田こてを使用する場合，約
350℃に設定して下さい。
注意： 半田こてを長く当てすぎると，基板のパター
ン（銅箔）がはがれてしまうことがあります
ので，注意して下さい。
• 粘性が強い
従来の半田よりも粘性が強いため，IC端子などが半田
ブリッジしないように注意して下さい。
• 従来の半田と混ぜて使用可能
無鉛半田には無鉛半田を追加するのが最適ですが，
従来の半田を追加しても構いません。
DSC-W110/W115_L2
—5—
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. PRECAUTION ON REPLACING THE SY-188 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-2. SELF-DIAGNOSIS FUNCTION
1-2-1. Self-diagnosis Function
1-2-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
When problems occur while the unit is operating, the LCD screen
shows a 4-digit display consisting of an alphabet and numbers, which
blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”
of the problem.
LCD screen
Blinks at 3.2 Hz
C
Repaired by:
32
Block
00
Detailed Code
Refer to “1-2-3. Self-diagnosis Code Table”.
C : Corrected by customer Indicates the appropriate
E : Corrected by service
step to be taken.
engineer
E.g.
13 ....Format the “Memory Stick Duo”.
32 ....Turn on power again.
DSC-W110/W115_L2
1-1
ENGLISH
JAPANESE
1-2-3. Self-diagnosis Code Table
Repaired by:
Self-diagnosis Code
Block
Function
Detailed
Code
C
1
3
0
1
C
3
2
0
1
E
6
1
0
0
E
6
1
1
0
E
E
9
9
1
2
0
0
1
0
Symptom/State
Correction
The internal memory has experienced a
format error.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” type error
The camera cannot read or write data
on the “Memory Stick Duo”.
Trouble with hardware
Format the internal memory.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a supported “Memory Stick Duo”.
Turn the power off and on again, or taking out and inserting the
“Memory Stick Duo” several times.
Turn the power off and on again.
Retry turn the power on by the power switch. If it does not
recover, check the focus reset sensor of lens block (pin wl of
Difficult to adjust focus
(Cannot initialize focus)
CN403 on the SY-188 board). If it is OK, check the focus motor
drive IC (IC401 on the SY-188 board).
Retry turn the power on by the power switch. Check the zoom
reset sensor of lens block (pin qs of CN403 on the SY-188
Zoom operations fault
board) when zooming is performed when the zoom button is
(Cannot initialize zoom lens.)
operated. If it is OK, check the zoom motor drive IC (IC401 on
the SY-188 board).
Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note)
Non-standard battery is used.
Use the compatible battery only.
Note: After repair, be sure to perform “1-3. PROCESS AFTER FIXING FLASH ERROR”.
1-3. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.
Method for Initializing the Flash Error Code
Initialize
Initializes the setting to the default setting. Even if you execute this function, the images
stored in the internal memory are retained.
1 Select [Initialize] with v/V on the control button, then press z.
The message “Reset to default settings” appears.
2 Select [OK] with v, then press z.
The settings are reset to the default setting.
To cancel initializing
Select [Cancel] in step 2, then press z.
• Be sure not to power off the camera while initializing.
DSC-W110/W115_L2
1-2
ENGLISH
JAPANESE
1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY
The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)
Note 1: When replacing the SY-188 board, erase the data in internal memory of the board before replacement.
Note 2: When replacing the SY-188 board, execute formatting and initialize the internal memory after replacement.
Method for Copying the Data in Internal Memory
Copy
Copies all images in the internal memory to a “Memory Stick Duo”.
1 Insert a “Memory Stick Duo” having sufficient free capacity.
2 Select [Copy] with v/V on the control button, then press z.
The message “All data on internal memory will be copied” appears.
3 Select [OK] with v, then press z.
Copying starts.
To cancel copying
Select [Cancel] in step 3, then press z.
• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little
remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.
• You cannot select images to copy.
• The original images in the internal memory are retained even after copying. To delete the contents of the
internal memory, remove the “Memory Stick Duo” after copying, then format the internal memory
([Format] in [Internal Memory Tool]).
• A new folder is created on the “Memory Stick Duo” and all the data will be copied to it. You cannot
choose a specific folder and copy images to it.
• The
(Print order) marks on the images are not copied.
Method for Formatting the Internal Memory
This item does not appear when a “Memory Stick Duo” is inserted in the camera.
Format
Formats the internal memory.
• Note that formatting permanently erases all data in the internal memory, including even protected images.
1 Select [Format] with v/V on the control button, then press z.
The message “All data on internal memory will be erased” appears.
2 Select [OK] with v, then press z.
Formatting starts.
To cancel formatting
Select [Cancel] in step 2, then press z.
DSC-W110/W115_L2
1-3
ENGLISH
JAPANESE
1-5. HOW TO WRITE DATA TO INTERNAL MEMORY
Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change the setting, use the write enable tool “WriteEnableTool.exe”.
Data writing method
1)
2)
3)
Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the “Sony Seus USB Driver”.
Start the Write Enable Tool and the SeusEX.
Click the [Activate Write Enable Mode] button of the Write Enable Tool.
4)
Upon completion of the setting change, the following message will be displayed.
5)
6)
7)
Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).
Write the data read out into the PC to the internal memory of the camera.
Disconnect the PC from the camera, and turn off the camera.
Note: By turning off the camera, the write enable setting is reset.
DSC-W110/W115_L2
1-4
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. SY-188基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
1-2. 自己診断機能
1-2-2. 自己診断表示
本機の動作に不具合が生じたとき，LCD画面にアルファベッ
トと4桁の数字が表示され，3.2Hzで点滅します。この5文字
の表示によって対応者分類および不具合の生じたブロックの
分類，不具合の詳細コードを示します。
1-2-1. 自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，
L C D 画面に，どう処置したらよいか判断できる表示を行い
ます。自己診断機能については取扱説明書にも掲載されて
います。
LCD画面
C : 3 2 : 00
3.2Hz点滅
C
対応者分類
C ：お客さま自身で対応
E ：サービスエンジニア
で対応
32
ブロック分類
00
詳細コード
「1-2 -3 . 自己診断コード表」
対応方法の違いにより分類
例 13 ･･･“メモリースティック を参照
デュオ”をフォーマッ
トする
32 ･･･電源を入れ直す
DSC-W110/W115_L2
1-5
ENGLISH
JAPANESE
1-2-3. 自己診断コード表
自己診断コード
対 ブロック
応
機能
者
詳細
コード
C
0
1
3
1
対応／方法
症状／状態
内蔵メモリにフォーマットエラーが 内蔵メモリをフォーマットする。
あった。
フォーマットしていない メモリー
スティック デュオ を入れた。
メモリースティック デュオ
をフォーマットする。
メモリースティック デュオ
壊れている。
が
新しい
メモリースティック デュオ
メモリースティック デュオ
タイプエラーを検出した。
の
規格内の
メモリースティック デュオ
読み／書きできない。
が
電源の入れ直し，または メモリースティック デュオ
の挿し／外しを数回試す。
メモリースティック デュオ
に交換する。
を挿入する。
C
3
2
0
1
ハードウェアトラブルを検出した。 電源を入れ直す。
E
6
1
0
0
操作スイッチの電源を入れ直す。
フォーカスが合いにくい。
（フォーカスの初期化ができない） 復帰しない場合はレンズブロックのフォーカスリセットセ
ンサ（SY-188基板CN403 wlピン）を点検する。異常なけ
ればフォーカスモータ駆動IC（SY-188基板IC401）を点検
する。
E
6
1
1
0
ズーム動作の異常。
（ズームレンズの初期化ができな
い）
操作スイッチの電源を入れ直す。
ズームボタンを操作したときにズーム動作をすればレンズ
ブロックのズームリセットセンサ（SY-188基板CN403 qs
ピン）を点検する。異常なければズームモータ駆動IC
（SY-188基板IC401）を点検する。
E
9
1
0
1
フラッシュの充電異常。
フラッシュユニットを点検または交換する。（Note）
E
9
2
0
0
規定外の充電池が使用された。
規定の充電池を使用する。
Note：交換後は，必ず「1-3. フラッシュエラー発生時の対処法」を行って下さい。
1-3. フラッシュエラー発生時の対処法
本機はフラッシュエラー（自己診断コードE：91：01）が発生した場合，高電圧による異常を防止するために自動的にフラッシュ
充電および発光禁止の設定になります。
フラッシュエラー発生後はエラーの解除を行う必要があります。エラーの解除はホーム画面から初期化操作を実行することによ
り行います。
設定リセット
お買い上げ時の設定に戻します。
［設定リセット］を実行しても、内蔵メモリーに記録されている画像は削除されません。
コントロールボタンの / で［設定リセット］を選び、中央の を押す。
「全ての設定内容をリセットします」というメッセージが表示される。
で［実行］を選び、中央の を押す。
設定リセットが実行される。
設定リセットを中止するには
手順
で、
［キャンセル］を選び、中央の
を押す。
• 設定リセット中は電源が切れないようにご注意ください。
DSC-W110/W115_L2
1-6
ENGLISH
JAPANESE
1-4. 内蔵メモリのデータコピーおよび消去方法
内蔵メモリのデータコピーまたは消去はホーム画面の操作から実行可能です。（消去する場合は内蔵メモリの初期化を行いま
す。）
Note1： SY-188基板交換の際は，基板交換前に内蔵メモリのデータを消去して下さい。
Note2： SY-188基板交換の際は，基板交換後に内蔵メモリのフォーマットおよび初期化を実行して下さい。
内蔵メモリのコピー方法
コピー
内蔵メモリーに記録した画像を、 メモリースティックデュオ に一括コピーします。
充分な空き容量のある メモリースティックデュオ を本体に入れる。
コントロールボタンの / で［コピー］を選び、中央の を押す。
「内蔵メモリーのデータがすべてコピーされます」というメッセージが表示される。
で［実行］を選び、中央の
コピーが実行される。
を押す。
コピーを中止するには
手順
で、
［キャンセル］を選び、中央の
を押す。
• 充分に充電したバッテリーをご使用ください。残量の少ないバッテリーを使用して画像ファイ
ルをコピーすると、バッテリー切れのためデータを転送できなかったり、データを破損するお
それがあります。
• 画像ごとのコピーはできません。
• データをコピーしても、内蔵メモリー内のデータは削除されません。内蔵メモリーの内容を消
去するには、コピー後に メモリースティックデュオ を本体から取りはずし、［内蔵メモリー
ツール］の［フォーマット］を行ってください。
• データをコピーすると メモリースティックデュオ 内に新しいフォルダが作成されます。コ
ピー先のフォルダを指定することはできません。
• データのコピーを行っても、
（プリント予約）マークの設定はコピーされません。
内蔵メモリのフォーマット方法
メモリースティックデュオ が本機に入っている場合は表示されません。
フォーマット
内蔵メモリーの管理領域をフォーマット（初期化）します。
フォーマットすると、プロテクトしてある画像も含めて、すべてのデータが消去され、元に戻せ
ません。
コントロールボタンの / で［フォーマット］を選び、中央の を押す。
「内蔵メモリーのデータがすべて消去されます」というメッセージが表示される。
で［実行］を選び、中央の を押す。
フォーマットが実行される。
フォーマットを中止するには
手順
で、
［キャンセル］
を選び、中央の
を押す。
DSC-W110/W115_L2
1-7
ENGLISH
1-5. 内蔵メモリへデータを書き戻す方法
通常は，PCからカメラの内蔵メモリへデータを書き込むことはできない設定になっています。
基板交換後などに，内蔵メモリへデータを書き戻す場合には，この設定を一時的に変更する必要があります。
設定の変更には，書き込み許可ツール（WriteEnableTool.exe）を使用します。
書き戻し方法
1) カメラとPCをマスストレージ接続し，ドライバを“Sony Seus USB Driver”に切り替える。
2) 書き込み許可ツールとSeusEXを起動する。
3) 書き込み許可ツールの[Activate Write Enable Mode]ボタンをクリックする。
4)
設定の変更が終了すると，次のメッセージが表示されます。
5)
6)
7)
ドライバを元に戻して、カメラとPCをマスストレージ接続する。
PCに読み出しておいたデータをカメラの内蔵メモリに書き込む。
カメラとPCの接続を解除し，カメラの電源をOFFにする。
注意： カメラの電源をOFFにすることにより，書き込み許可の設定が解除されます。
DSC-W110/W115_L2
1-8E
JAPANESE
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor (C901) is charged up to the maximum
300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
R:1 kΩ/1 W
(Part code: 1-215-869-11)
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
ST-180 Board
1 kΩ/1 W
C901
Wrap insulating tape.
DSC-W110/W115_L2
2-1
2-1. IDENTIFYING PARTS
Cabinet (Rear)
Cabinet (Upper)
⋅ AF-112 Board
⋅ ST-180 Board
BT Holder Section
⋅ MC-189 Flexible Board
⋅ ST-188 Flexible Board
⋅ SY-188 Board
LCD
LCD Frame
⋅ SW-520 Board
⋅ SW-533 Flexible Board
Cabinet (Front)
Lens Block
⋅ CCD Block (CD-719 Flexible Board)
- DISASSEMBLY FLOW 2-2-1. LCD SECTION
⋅ Cabinet (Rear)
⋅ LCD
2-2-2. FRONT SECTION
⋅ Cabinet (Front)
⋅ Lens Block
2-2-3. BT HOLDER SECTION
⋅ Cabinet (Upper) Block
⋅ SY-188 Board
DSC-W110/W115_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW
HARDWARE LIST
2-2-1. LCD SECTION
Follow the disassembly in the numerical order given.
1 Cabinet (Rear) (1-1 to 1-6)
2 LCD (2-1 to 2-17)
1 Cabinet (Rear)
1-6
1-5 (Boss)
HELP 1
1-1 (#20)
1-3 (#20)
2-17
1-4
(Boss)
2-15
2-16
(Solder)
2-10
1-2 (#20)
2-6 (#118)
2-11
HELP 3
2-7
(Claw)
2-2 (#20)
2LCD
2-14
(Claw)
2-12
HELP 2
2-13
(Claw)
2-8
2-4 (#20)
2-3
Note: High-voltage cautions
2-9
Discharging the Capacitor
Short-circuit between two points
with the short jig about 10 seconds.
2-1
Front Section
R:1 kΩ/1 W
(Part code: 1-215-869-11)
(See Page 2-4)
2-5 (#20)
ST-180 Board
C901
DSC-W110/W115_L2
2-3
2-2-2. FRONT SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 Cabinet (Front) (1-1 to 1-3)
2 Lens Block (2-1 to 2-6)
2-3
HELP 4
BT Holder Section
(See Page 2-5)
1 Cabinet (Front)
2-4
HELP 4
1-3 (Claw)
2-2
2-5
2-1 (#20)
1-1 (Claw)
1-2 (Claw)
2Lens Block
HELP 8
DSC-W110/W115_L2
2-4
2-6
2-2-3. BT HOLDER SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 Cabinet (Upper) Block (1-1 to 1-4)
2 SY-188 Board (2-1 to 2-5)
2SY-188 Board
1 Cabinet (Upper) Block
1-4
HELP 6
1-1
2-5
2-1 (#3)
(Solder)
2-2 (Claw)
1-3 (Claw)
HELP 5
HELP 7
2-3 (Claw)
DSC-W110/W115_L2
2-5
1-2
(#20)
2-4
HELP 9
2-3. PRECAUTIONS WHEN HOLDING THE LENS BLOCK
• Hold the Lens Block at the center of both sides.
Hold here.
• Do not hold the following part.
OVF
Lens Flexible Board
Lens Barrel
Optical Stepping Motor
∗Very weak
Lens Barrier
∗Very weak
Zoom Motor
Focus Lens
OVF Cam Plate
DSC-W110/W115_L2
2-6
2-4. BARRIER ASSY REPLACING METHOD
Removal
1 Turn on the power switch and extend the lens.
2 Detach the battery.
3 Pour a solvent such as alcohol from two places A to the tweezers or a needle shown below into a gap of Ornamental Ring A.
4 Remove while turning the Ornamental Ring A right and left.
Ornamental Ring A
Tweezers
A
Solvent
5 Remove Barrier Assy by disengaging four claws.
Claws
Claws
Barrier Assy
Installation
1 Affix two Barrier Tapes to Barrier Assy.
Note: The tape must not be wrinkled.
2 With four claws fitted in position, install the Barrier Assy.
Barrier Assy
Claws
Barrier Tape
Barrier Tape
Only one hook has
different shape.
Claws
3 Peel off release papers of Barrier Tapes.
4 Install Ornamental Ring A and press it lightly.
Barrier Tapes
Ornamental Ring A
DSC-W110/W115_L2
2-7
Barrier Assy
2-5. LENS MOTOR REPLACING METHOD
Replace the parts if the following events appear when the power switch is turned on.
1 "Turn off and on the power" is displayed without performing the zoom operation.
Replace Zoom Gear Block if a damage of lens barrel due to a drop of camera is not found.
(See "2-5-1. Zoom Gear Block Replacing Method")
Replace Lens Block if such replacement does not improve the failure.
2 "Turn off and on the power" is displayed after the "lens zooming in and out" operation over its full stroke was repeated
3 times.
Replace Optical Stepping Motor. (See "2-5-2. Optical Stepping Motor Replacing Method")
Replace Lens Block if such replacement does not improve the failure.
2-5-1. Zoom Gear Block Replacing Method
Removal
1 Remove one screw.
2 Remove Zoom Gear Block upward.
3 Remove Naruto Gear (S).
4 Disengage two claws A and B in this order to remove FG Plate Spring.
Note: The FG Plate Spring cannot be reused.
5 Remove two sensors on the lens flexible board.
6 Break two solders, and remove the lens flexible board.
1 Screw
6 Solders
5 Sensors
2 Zoom Gear Block
Claw A
Zoom Gear Block
Claw B
4 FG Plate Spring
3 Naruto Gear (S)
Installation
1 Confirm the direction of Zoom Gear Block, and install the lens flexible board with two solders.
2 Pass the lens flexible board through the mold of Zoom Gear Block to install two sensors.
3 Engage two claws A and B in this order to install FG Plate Spring.
4 Install Naruto Gear (S).
6 Screw
5 With four bosses fitted in position, install Zoom Gear Block.
6 Tighten one screw.
* Tightening torque = 0.049 ± 0.01N • m (0.5 ± 0.1kgf • cm)
Front Side
5 Zoom Gear Block
Mold
1 Solders
Bosses
2 Sensors
Rear Side
Claw B
4 Naruto Gear (S)
Zoom Gear Block
Claw A
DSC-W110/W115_L2
Bosses
Mold
3 FG Plate Spring
2-8
2-5-2. Optical Stepping Motor Replacing Method
Removal
1 Disengage the lens flexible board from the claw.
2 Remove solders of the lens flexible board.
3 Remove Zoom Gear Block by referring to the removal 1 to 3 in "2-5-1. Zoom Gear Block Replacing Method".
4 Remove three screws.
5 Remove the lens rear block.
4 Screws
2 Solders
5 Lens Rear Block
1 Claw
3 Zoom Gear Block
6 Remove one screw.
7 Remove Optical Stepping Motor.
8 Break four solders to remove the lens flexible board.
6 Screw
7 Optical Stepping Motor
8 Solders
DSC-W110/W115_L2
2-9
Installation
1 Install the lens flexible board with four solders.
2 Referring to the following figure, check each part state of lens rear block.
3 Install Optical Stepping Motor.
4 Tighten one screw.
* Tightening torque = 0.049 ± 0.01N • m (0.5 ± 0.1kgf • cm)
2 Check the state of each part
4 Screw
3 Optical Stepping Motor
Check if the shaft fits with the groove.
Check if the hook fits with the shaft
1 Solders
Lens Rear Block
5 Rotate the gear of lens barrel in arrow direction to extend the lens.
6 Check the inside of lens barrel and the lens for dust or stain, and then install the lens rear block.
7 Tighten three screws.
* Tightening torque = 0.049 ± 0.01N • m (0.5 ± 0.1kgf • cm)
8 Install Zoom Gear Block by referring to the installation 4 to 6 in "2-5-1. Zoom Gear Block Replacing Method".
9 Solder the lens flexible board.
0 Assemble the lens flexible board with the mold of Lens Block.
qa Engage the lens flexible board with the claw.
7 Screw
9 Solders
qa Claw
6 Lens Rear Block
0 Molds
8 Zoom Gear Block
5
DSC-W110/W115_L2
2-10
2-5-3. FINAL INSPECTION (NO FAULT IN ACTUAL MOTION/ACTUAL SCREEN)
1 Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
2 Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3 Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
4 Appearance condition
Scratches or stains must not be noticeable, except that the customer permits them.
5 Foreign matters on the lens
The lens condition must not be worse than that when the camera was received from the customer.
Upward
Lens at WIDE end
Upper oblique 45˚
Full stroke check
Horizontal
Lower oblique 45˚
Lens at TELE end
Downward
DSC-W110/W115_L2
2-11E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP 1: LCD Window Adhesive Sheet Kit
LCD Window Adhesive Sheet Kit must use only
the part of LCD window edge.
Please discard other parts.
HELP 3: LCD Insulating Sheet
- Front Side LCD Insulating Sheet
Discard parts
Hole
- Rear Side LCD Insulating Sheet
Paste parts
Hole
LCD Window Adhesive Sheet Kit
HELP 2: LCD Flexible Fixed Sheet
LCD Flexible Fixed Sheet
LCD Flexible Board
LCD Frame
DSC-W110/W115_L2
HELP
HELP 4: Tape (AF)/Capacitor Protection Sheet
HELP 5: BT Terminal Harness
BT Holder
Tape (AF)
BT902 (White)
BT903 (Black)
BT901 (Red)
Tape (AF)
SY-188 Board
BT Terminal Harness
Capacitor Protection Sheet
BT Holder Mold
DSC-W110/W115_L2
HELP
HELP 6: Sheets and Harness of ST-180 Board
- Top View ST Insulating Sheet Harness (HN-062) (Gray)
Harness (HN-061) (Yellow)
ST-180 Board
Harness (HN-059) (Pink)
Harness (HN-060) (Blue)
When connecting the harness to
the strobe capacitor terminals,
wind the naked leads of the harness
around the terminals by more than
1.5 turns, and then solder them.
Mic Harness (Orange)
Mic Harness (White) Lithium Insulating Sheet
Capacitor
- Bottom View ST-180 Board
Speaker Harness (Red)
Speaker Harness (Black)
Harness (HN-060) (Blue)
ST Insulating Sheet
Harness
BT900
Harness (HN-059) (Pink)
Lithium Insulating Sheet
- Rear View ST Insulating Sheet
ST-180 Board
Lithium Insulating Sheet
Capacitor Protection Sheet
9.5 ± 1mm
AF-112 Board
Capacitor Protection Sheet
DSC-W110/W115_L2
HELP
HELP 7: Installation Method of Battery Terminal Board
1 Insert the battery terminal board into a slit in the BT holder to install.
* The battery terminal board is attached with the notch for installation.
BT holder
Notch
Battery terminal board
Battery terminal
board
2 Fold the notch 3 or 4 times repeatedly to break.
Notch
Battery terminal board
Notch
DSC-W110/W115_L2
HELP
HELP 8: Lens Flexible Board/CD-719 Flexible Board
CD-719 Flexible Board
Apply the fold trace.
Lens Flexible Board
Apply the fold trace.
HELP 9: MC-189 Flexible Board
Apply the fold trace.
MC-189 Flexible Board
DSC-W110/W115_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2)
POWER BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (2/2)
POWER BLOCK DIAGRAM (2/2)
DSC-W110/W115_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CD-719 FLEXIBLE BOARD
SY-188 BOARD (1/2)
2
5
26
27
24
23
39
38
RG
VST
VHLD
VSUB
VSUB_CONT
D6
D5
C4
Q301
X201
33.75MHz
2
K4
V1, V2, V3A, V3B, V4,
V5A, V5B, V6 - V10
GEN_TG_CLK
C1
IC202
1
CLOCK
3
GENERATOR
5
(8/10)
IC203
(1/2)
XCS_ PANEL
XDD_SYS_RST
AF18
GEAR_ON
GEN_SYS_CLK
XCS_FE, XIC_203_3_SCK, IC_203_3_SO
36 - 30
LCD_CK, LCD_HD, LCD_VD
U19
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
Y13 MODE CONTROL
P19
(4/10, 5/10)
Y12
4
3
IC_203_2_SO, XIC_203_2_SCK
DETECT_V_OUT
37
XDD_SYS_RST
E7
IC_203_2_SO,
XIC_203_2_SCK
XCS_AUDIO
V8
1
XDD_SYS_RST
OVERALL (2/2)
(PAGE 3-2)
AF8
IC_203_AUIN
IC401
LENS DRIVE D4
(2/10)
XLENS_DRIVER_PS
2.5INCH
COLOR
LCD
XCS
XRST
SI, XSCK
TESTOUT
ST-180 BOARD (1/2)
CN707
(1/2)
E4
B6
E6
E5 AUDIO AMP
(7/10)
A5, A2
IC_203_AUOUT
R7, AF25
Q302
MCK, Hsync, Vsync
ST-188
FLEXIBLE
BOARD (1/2)
MIC_SIG
CN002
(1/2)
12
20
IC603
AE8
VSUB_CONT_PRE,
VSUB_CONT_POST
D0 - D6
27, 26
36
AF22
E18, B23
FOCUS
RESET
SENSOR
19
C2, C3, B3
M
K6, K5, J6, J5
M
H1A, H2A, H1B, H2B
G7, H6, G6, G5,
H5, H4, G4, F4,
E4, D7, H7, D4
M
5, 6, 8, 9
M
IRIS
MOTOR
15 - 22, 25 - 28
FOCUS
MOTOR
31, 32, 21, 22
ZOOM
MOTOR
1, 3, 6 - 12,
14 - 16
SHUTTER
MOTOR
AE23
CA_FD
29 - 27
CA_HD
A2
CCD SIGNAL
PROCESS,
TIMING
A4
GENERATOR
(1/10)
5, 6
IC304
F7
A3, B1
PWR_SAVE
LCD_D1 - LCD_D7
5, 6
1 16
7M CCD
IMAGER
CA_AD00 - CA_AD13
F3, E3
H10
B19, E17, A19, E16,
A18, D16, A17
10 BUFFER 14
(1/10)
IC003
CN704
B18, D18, B17
IC309
AB21, AC21, AB20, AC20, AB19,
AC19, AC18, AE21, AF21, AE20,
AF20, AE19, AF19, AE18
32
17
CN301
CCD_OUT
LCD901 (1/2)
LCD MODULE
V19, D19, C25
IRIS
(METER)
LENS
D1, E3 - E1, F3- F1,
G3 - G1, H3 - H1, J1
LENS BLOCK
SP±
D1
AU_LINE_OUT
MIC901
MICROPHONE
BLOCK
SP±
SP901
SPEAKER
MC-189 FLEXIBLE
BOARD (1/2)
CN709
(1/2)
H11
MIC_SIG
A_OUT_L
38
16
ZM_SENS_1ST
Z_BOXPI-1_SENS_OUT, Z_BOXPI-2_SENS_OUT
ZM_DC_FG_1A, ZM_DC_FG_1B
Z_BOXPI-1_GND, Z_BOXPI-2_GND
XZM_FG_LED
LENS TEMP
SENSOR
L_TEMP_OUT
7
TZ_HALL_TEMP
Y18, Y17
USB_DP, USB_DM
2
AD26
OVERALL (2/2)
(PAGE 3-2)
MSX_BS,
MSX_D0 - MSX_D3,
MSX_CLK
USB_VBUS
XMS_IN
V_OUT
36
HD Y
HD Pb
HD Pr
34
7
9
15, 17
HD_Y
HD_Pb
HD_Pr
Y10
M8
L8
V_LINE_OUT
USB_DP, USB_DM
USB_VBUS
13
CN708
MS_BS,
MS_D0 - MS_D3,
MS_CLK
6
MEMORY
STICK
DUO
AF3
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
05
DSC-W110/W115_L2
3-1
20
24
4
2
10, 12
IC602
4
3 VIDEO AMP 5
(7/10)
IC_203_YOUT
AB13
IC_203_PBOUT
AF12
IC_203_PROUT
AC12
Y1, AA1
W18, AB26, W17
AB23, AA23, AC25
VIDEO_AMP_ON
2 - 5, 7, 8
FC_SENS
XFC_RST_LED
R8, AE25
D3, F1
A2, C4, B2
G1, E4
D5, A6, B6, C5
B7, C6, D6, E6
MSHUT_DIR, MSHUT_EN
20, 18
12
SHUTTER
MOTOR
DRIVER
ZM_DIR_A, ZM_EN_A, ZM_BRK_B
22, 17
Z_PI_SENS_OUT
29
27
ZOOM
MOTOR
DRIVER
FC_DIR_A, FC_DIR_B, FC_EN_A
T8
A13 - A15,
B13 - B15
F_PI_SENS_OUT
FPI_GND
ZOOM
RESET
SENSOR
SHUTTER_±
FOCUS
MOTOR
DRIVER
IRIS_M_DIR_2B, IRIS_M_BRK_2B
Y11, W11
ZOOM
FG
ZOOM_A, ZOOM_A-
IRIS MOTOR
DRIVER
B4, B5
SHUTTER(±)
26 - 23
Z_DC_MOTOR(±)
FOCUS_A, A, B, B
1-4
13 - 16
F_MOTOR_A, F_MOTOR_A,
F_MOTOR_B, F_MOTOR_B
ND_±
F4, F3
5, 6
ND(±)
D2, B1
CN403
6
CN001
(1/2)
MULTI
CONNECTOR
3-2. OVERALL BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
MC-189 FLEXIBLE
BOARD (2/2)
SY-188 BOARD (2/2)
CN709(2/2)
K6
G9
3
MODE_DIAL1,
MODE_DIAL2
BL_L
1, 2
KEY_AD1,
KEY_AD2
2
OVERALL (1/2)
(PAGE 3-1)
XMS_IN
D10
USB_VBUS
E7
BL_L
8
XPWR_OFF
C10
MODE_DIAL1,
MODE_DIAL2
E10
XIC_203_RST_REQ
XDD_SYS_RST
D6
C9
XCS_DD
CN002
(2/2)
S102
POWER
BT900
LITHIUM
BATTERY
XAF_LED
ST-188
FLEXIBLE
BOARD (2/2)
14
30
XPWR_ON
VL_3V
C4
C6 - C8
C5
IC_203_0_SO,
IC_203_0_SI,
XIC_203_0_SCK
CN707
(2/2)
23
XAF_LED
9
XAF_LED
S101
(SHUTTER)
13
15
D101
(AE/AF LOCK)
16
D102
FLASH CHARGE/
RECORD
17
D103
(POWER)
+
XE_H
TRIGGER
TRIGGER_GND
18
Q001
FLASH
DRIVE
XAE_LOCK_LED
XSTRB_LED
XPWR_LED
XAE_LOCK_SW
XSHUT_SW
19
17
XAE_LOCK_LED
16
XSTRB_LED
15
XPWR_LED
14
D001
3
2
4
1
1, 2
7
IC001
FLASH
CONTROL,
CHARGE
CONTROL
(1/2)
10
9
6
STRB_CHG
8
XSTRB_FULL
12
STRB_CHG_CONT
11
4
9
STRB_ON
STRB_CHG
XSTRB_FULL
STB_CHG_CNT
24
20
21
B2
Y9
STRB_ON1
23
05
DSC-W110/W115_L2
3-2
V2
H9
H15
Y16
+
BT902
S
17, 21
21 - 26
–
W8
XACCESS_LED
BATT_SIG
BT901
BT903
W9
D708
19
XACC_IN
26
UART Rx,
UART Tx
IC201
N19
R19
H8
ST_UNREG
33
BATTERY
DETECTOR
(8/10)
XDD_SYS_RST
T001
15
XE_L
XAE_LOCK_SW
XSHUT_SW
E4
1
OVERALL (1/2)
(PAGE 3-1)
MODE_DIAL1,
MODE_DIAL2
FLASH
UNIT
BATT_UNREG
AB7, AE6 AC8, AF6
XAF_LED
UART_Rx, UART_Tx
BATTERY
TERMINAL
XDD_SYS_RST
KEY_AD1, KEY_AD2
C901
CHARGING
CAPACITOR
IC_203_1_UI, IC_203_1_UO
D004
D201
SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
XACC_IN
XAV_JACK_IN
XCS_IC_201,
XIC_203_1_SCK,
IC_203_1_SO,
IC_203_1_SI
7
D002
XACV_IN
A23
H5
F5
AF-112 BOARD
CHARGE_V
W12
AB18
18
2
XACV_DET
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
G8 MODE CONTROL
(4/10, 5/10)
W20, H18, B24, G18
7, 6
MODE
DIAL
BL_L
ST-180 BOARD (2/2)
K8
H17, A24, G17
S010
KEY_AD1,
KEY_AD2
4, 5
10, 9
FUNCTION
KEY
BL_H
6
X001
32.768kHz
IC203
(2/2)
S001 - S009,
S011
BACKLIGHT
XDIRECT_PB
D7
D9
ACV_UNREG
15, 9
5
XPWR_ON
XDIRECT_PB
XPWR_ON
XDIRECT_PB
19, 12
CN706
20
XPOWER_ON
D001
BATT_UNREG
K7
CN001
S012
XACV_DET
Q001,
Q002
D26, G19
SW-533
FLEXIBLE
BOARD
SW-520 BOARD
LCD901 (2/2)
LCD MODULE
IC001
DC/DC
CONVERTER
(9/10)
B1, B5, C5, D5
MS_VCC
CAM_12.5V
CAM_-7.5V
USB_3.2V
M_5.0V
D_3.1V
A_3.1V
DDR_1.8V
D_1.85V
D_1.25V
BL_H
11
23, 25
ACV_UNREG
ST_UNREG
27 - 32
XPOWER_ON
XPWR_ON
D709
(ACCESS)
CN001
(2/2)
MULTI
CONNECTOR
3-3. POWER BLOCK DIAGRAM (1/2)
ACV_UNREG
SY-188 BOARD (1/2)
F001
CN709
27 - 32
23, 25
MC-189
FLEXIBLE
BOARD
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
F002
ACV_UNREG
IC001
Q001, Q002
19
CN001
MULTI
CONNECTOR
XACV_DET
20
DC/DC CONVERTER (9/10)
XACV_DET
G6 UNREG
D001
D002
CHARGE_V
21 - 26
17, 21
G3 MS_PWR_ON
MS_VCC
MS_PWR_OUT F3
MS_PWR_IN F4
BATT_UNREG
9
CN708
MEMORY
STICK
DUO
DDC5_PSW H1
L001
7
XPOWER_ON
11
DDC5_LX_1 J3
DDC5_LX_2 K3
XPOWER_ON
ST_UNREG
D006
DDC5_VO_1
DDC5_VO_2
LDO3P1U_IN
LDO3P1U_OUT
XACV_IN
BATTERY
TERMINAL
BT902
S
BATT_SIG
P144_SOA0
P143_SIA0
P142_XSCKA0
P120_INTP0
E4 TXRX
BT903
–
D_3.1V
A
USB_3.2V
L002
CAM_12.5V
D007
BATTERY
DETECTOR
(8/10)
BATT_UNREG
+
M_5.0V
B+ SWITCH
Q003
DDC12_LX_1 J9
DDC12_LX_2 K9
IC201
BT901
J2
K2
H4
J5
D
D5
C5
B5
B1
IC_203_1_SI
IC_203_1_SO
XIC_203_1_SCK
XCS_IC_201
DDC12_VFB H8
Q006, Q007
POWER (2/2)
(PAGE 3-4)
DDC12_PWR_IN1 G8
DDC12_PWR_IN2 G7
D008
H10 DDCM7P5_PWR
DDCM7P5_LX J10
DDCM7P5_VFB F8
C2 DDC2P9_PWR_1
B1 DDC2P9_PWR_2
DDC2P9_VO_1 F1
DDC2P9_VO_2 F2
DDC2P9_VFB G1
CAM_-7.5V
B2 XRESET
L006
D_3.1V
L008
XDD_SYS_RST
POWER (2/2)
(PAGE 3-4)
B3 DDC1P2_PWR
DDC1P2_LX A4
DDC1P2_VFB B2
B8 DDC1P8_PWR
DDC1P8_LX A8
DDC1P8_VFB B6
A_3.1V
D_3.1V
D_1.25V
L009
D_1.85V
E
DDR_1.8V
LDO1P8_OUT A7
LDO3P1E_OUT F5
R008
R005
D004
RTCBAT H5
R006
B
POWER (2/2)
(PAGE 3-4)
C
MS_PWR_ON
IC_203_0_SI
IC_203_0_SO
XIC_203_0_SCK
XCS_DD
XIC_203_RST_REQ
XPWR_OFF
BATT_SENS
VL_3V
MS_PWR_ON
C7
C6
C8
C5
D6
C10
F6
XPWR_ON
XDIRECT_PB
SO
SI
SCK
XCE
XRESET_REQ
XPWR_OFF
UNREG_MON
L004
D009
BL_H
DDCBL_VO F9
BL_L
DDCBL_VL E10
D7 XPWR_ON1
D9 XPWR_ON3
POWER (2/2)
(PAGE 3-4)
F003
DDCBL_LX F10
XSYS_RESET C9
D_3.1V
XDD_SYS_RST
05
DSC-W110/W115_L2
3-3
XDD_SYS_RST
Q008
1.85V
DISCHARGE
POWER (2/2)
(PAGE 3-4)
3-4. POWER BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
LCD901
LCD MODULE
M_5.0V
L702
D_3.1V
L701
XDD_SYS_RST
CN704
VDDD2IN
15
VDD1A
VDD1D
XRST
CN706
BL_H
10
BL_L
8
BL_H
BL_L
A
ST_UNREG
XDD_SYS_RST
XDIRECT_PB
POWER (1/2)
(PAGE 3-3)
CAM_12.5V
CAM_-7.5V
E
D_1.85V
D_3.1V
D_3.1V
BL_H
BL_L
M_5.0V
A_3.1V
M_5.0V
A_3.1V
M_5.0V
BL_H
BL_L
S012
CN707
XPWR_ON
18
D_3.1V
BACKLIGHT
CN001
1
3
5
ST-188
FLEXIBLE
BOARD
7, 8
A_3.1V
D_3.1V
SW-520 BOARD
SW-533
FLEXIBLE
BOARD
6
C
POWER (1/2)
(PAGE 3-3)
2.5INCH
COLOR
LCD
8
9
3
ST-180 BOARD
CN002
S102
POWER
14
D101
(AE/AF LOCK)
24, 25
SY-188 BOARD (2/2)
AU_AVCC
4 VDD VOUT 1
AF-112 BOARD
D102
FLASH CHARGE
RECORD
IC603
POWER (1/2)
(PAGE 3-3)
AUDIO AMP
(7/10)
D201
SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
D103
(POWER)
3 CE
R601
VIDEO AMP
(7/10)
D601
A_3.1V
T001
R780
D709
(ACCESS)
R253
L241
VL_3V
USB_3.2V
Q701, Q702
ST_UNREG
ST_UNREG
ST_5V
M_5.0V
D_3.1V
R254
FB282
IC203
POWER (1/2)
(PAGE 3-3)
IC001
R205
CLOCK
GENERATOR
(8/10)
A24
H17
G17
A23
W12
G8
T7
AE7
VL_3V
D
POWER (1/2)
(PAGE 3-3)
IC_203_1_SI
IC_203_1_SO
XIC_203_1_SCK
XCS_IC_201
SIO1_RXD
SIO1_TXD
SIO1_SCK
GPS_04
2
VL_3V
CAM_-7.5V
L302
FB307
CN301
CAM_12.5V_CD
CAM_-7.5V_CD
GPS_13 W7
STRB_UNREG_ON
D_3.1V
IC310
3
3.3V REG
(1/10)
CE
4 VDD VOUT 1
6 Vin
Vout 4
IC308
2.8V REG
(1/10)
XDD_SYS_RST
D_3.1V
M_5.0V
A_3.1V
XZM_RST_LED
DSC-W110/W115_L2
3-4E
2
IC003
7M
CCD IMAGER
IC309
BUFFER
(1/10)
LENS BLOCK
IC304
CCD SIGNAL
PROCESS,
TIMING GENERATOR
(1/10)
XZM_RST_LED
05
12
FB311
FB310
1 Vcont
GPE_03 J8
CD-719 FLEXIBLE
BOARD
FB313
Q303
-7.5V
DISCHARGE
M_5.0V
BT900
LITHIUM
BATTERY
30
CAM_12.5V
SIO0_RXD
SIO0_TXD
SID0_SCK
SIO0_SCS
XRESET_REQ
GPE_00
GPE_15
ADC0_IN6
K8 GPE_05
G18
B24
H18
W20
VL_3V
L301
D_3.1V
XACV_IN
FLASH
UNIT
FLASH CONTROL,
CHARGE CONTROL
(1/2)
CPU,
CAMERA DSP,
AV SIGNAL PROCESS,
LENS CONTROL,
MODE CONTROL
(4/10 - 6/10)
USB_3.2V
B
10
IC202
D_3.1V
D_1.85V
FB283
IC_203_0_SI
IC_203_0_SO
XIC_203_0_SCK
XCS_DD
XIC_203_RST_REQ
XPWR_OFF
MS_PWR_ON
BATT_SENS
22
D001
L001
STRB_UNREG_ON
Q401
SENSOR SWITCH
XZM_RST_LED
D_1.25V
DDR_1.8V
D_1.85V
1-3
2.8V REG
(7/10)
D_1.25V
D_1.85V
DDR_1.8V
D_3.1V
IC602
AB18 XRESET
29 - 31
IC601
R402
R412
CN403
Z_PI_SENS_Vcc
Z_BOXPI-1_SENS_Vcc
Z_BOXPI-2_SENS_Vcc
10
ZOOM
RESET
SENSOR
21
19
ZOOM
FG
28
FOCUS
RESET
SENSOR
R411
R401
F_PI_SENS_Vcc
C1 RESET
IC401
LENS DRIVE
(2/10)
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
LENS BLOCK
SW-520 BOARD
CD-719 FLEXIBLE BOARD
ST-188 FLEXIBLE BOARD
1
1
1
10
1
10
10
1
CN001
SW-533 FLEXIBLE BOARD
31
1
31
39
IC003
(Not supplied)
BT901 BT902
+
BT903
−
BATTERY
TERMINAL
HARNESS (HN-067) (Red)
HARNESS (HN-068) (White)
HARNESS (HN-069) (Black)
S
BT900
LITHIUM BATTERY
ST-180 BOARD (SIDE B)
31
30
1
2
CN707
LCD901
LCD MODULE
1
2
10
CN706
2.5INCH
COLOR
LCD
BACKLIGHT
39
38
1
Black
Red
CN301
30
CN002
1
2
31
CN403
1
2
CN704
38
39
1
MIC901
MICROPHONE
BLOCK
IC203
(Not supplied)
29
28
CN708
MEMORY STICK
CONNECTOR
FLASH UNIT
2
1
10
SP901
SPEAKER
12
HARNESS (HN-060) (Blue)
CN709
38
39
LEVEL3
SY-188 BOARD
(SIDE B)
LEVEL3
SY-188 BOARD
(SIDE A)
LOCK
C901
CHARGING CAPACITOR
2
1
ST-180 BOARD (SIDE A)
White
Orange
11
CN001
MULTI CONNECTOR
HARNESS (HN-062) (Gray)
AF-112 BOARD
HARNESS (HN-061) (Yellow)
HARNESS (HN-059) (Pink)
1
28 26
25
2
1
39
27
05
MC-189 FLEXIBLE BOARD
DSC-W110/W115_L2
4-1
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CD-719 FLEXIBLE BOARD (CCD IMAGER)
SW-520 BOARD
(CONTROL SWITCH)
ST-180 BOARD (1/2) (FLASH DRIVE)
MC-189 FLEXIBLE BOARD
(MULTI CONNECTOR)
ST-180 BOARD (2/2) (CONTROL SWITCH)
ST-188 FLEXIBLE BOARD
(SY-ST CONNECTION)
AF-112 BOARD (AF ILLUMINATOR)
SW-533 FLEXIBLE BOARD
(SY-SW CONNECTION)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-W110/W115_L2
ENGLISH
4-2. SCHEMATIC DIAGRAMS
JAPANESE
4-2. SCHEMATIC DIAGRAMS
(ENGLISH)
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
Color bar chart
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 24 cm (PTB-450)
L = 11 cm (PTB-1450)
Pattern box
Front of the lens
L
Kinds of capacitor
External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Camera
A B
Red
Blue
White
Magenta
H
Cyan
Green
Yellow
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
A=B
B A
Fig. a (Video output terminal output waveform)
Electronic beam
scanning frame
CRT picture frame
Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
When indicating parts by reference number, please
include the board name.
The components identified by mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
DSC-W110/W115_L2
4-2
ENGLISH
4-2. SCHEMATIC DIAGRAMS
JAPANESE
(JAPANESE)
回路図共通ノート
（他に必要なノートは各ブロックに記載してあります）
【回路図ノート】
1. 接続図
・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のもの
はその耐圧を省略。単位はすべてμF（pはpF）。
・チップ抵抗で指示のないものは，1／10W以下。
kΩ＝1000Ω，MΩ＝1000kΩ
・チップ部品交換時の注意
取り外した部品は再使用せず，未使用の部品をご使用くださ
い。
タンタルコンデンサのマイナス側は熱に弱いため注意してくだ
さい。
・チップ部品には下記のように表示したものがあります。
例
C 541
L 452
22U
10UH
TA
A
2520
↑ ↑
↑
種類 ケースサイズ
外形寸法（mm）
・抵抗，コンデンサ，ICなど定数にXXがあるものは，使用して
いない事を示しています。このため，使用していない回路が記
載されている事があります。
・★印のある部品は，機種などにより異なりますので機能別マウ
ント一覧表を参照してください。
・可変抵抗と半固定抵抗で，B特性の表示を省略。
・信号名表記について，下記のような場合があります。
XEDIT → EDIT
PB/XREC → PB/REC
・2は不燃性抵抗。
・1はヒューズ抵抗。
・Cはパネル表示名称。
・AはB＋ライン。
・BはB−ライン。
・JはBライン（＋，−）の入出力方向を示す。
・Cは調整名称。
パターンボックス
カラーバーチャート
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 24 m (PTB-450)
L = 11 cm (PTB-1450)
パターンボックス
レンズ前面
L
カメラ
2. 図a及び図bの波形が得られるように画枠調整して下さい。
H
シ
黄 ア
ン
A B
マ
ゼ
白 ン
ダ 赤
緑
A=B
青
B A
図a（映像入出力端子出力波形）
【電圧・波形測定条件ノート】
・電圧値及び信号波形はパターンボックスのカラーバーチャート
を被写体としたときの測定点対アース間の参考値。
（デジタルマルチメータ；入力インピーダンス DC10MΩ使
用）
・使用テスタの入力インピーダンスにより電圧値が多少異なりま
す。
電子ビーム走査線
ブラウン管の画像枠
イメージャ交換時の注意
図b（テレビモニタの映像）
・イメージャを交換した場合は，カメラ部の全調整を
行ってください。
・イメージャは構造上，静電気により破壊される恐れが
あるため，MOS ICと同様に注意して取り扱ってくだ
さい。
また，受光部にはゴミの付着，および強い光がはいる
ことのないように注意してください。
0印の部品，または0印付きの点線で囲まれた部品は，
安全性を維持するために重要な部品です。
従って交換時は，必ず指定の部品を使用して下さい。
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定して下さい。
DSC-W110/W115_L2
4-3
1
3
2
4
5
6
7
8
LND004
LND005
LND006
C
GND
4
GND
5
H1A
7
GND
LND008
8
H2B
9
H2A
10
GND
LND012
LND013
LND014
LND015
LND016
11
GND
12
CAM_12.5V_CD
13
GND
14
GND
15
V3B
16
V4
17
V5A
LND018
18
V5B
LND019
19
V6
LND020
20
V7
LND022
LND023
LND024
LND025
LND026
LND027
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
21
V3A
22
V2
23
VHLD
24
VST
25
V1
26
V8
27
V9
28
V10
29
GND
30
GND
31
GND
32
CCD_OUT
33
GND
34
GND
35
GND
36
RG
37
GND
VHLD
N.C.
N.C.
3
2
1
4
VL
RG
V1
B
29 30 31 32
V3A
6
7
5
VHLD
V3A
V4
V3B
V3B
V5A
9
10
8
V4
V6
V5B
11
VH
21 22 23 24 25 26 27 28
H1A
C005
0.1u
10V
B
H2B
LND017
LND021
C009
0.1u
16V
B
H1A
H1B
H1B
LND009
C003
0.1u
16V
B
RG
6
LND010
E
3
LND007
LND011
D
GND
2 CAM_-7.5V_CD
CCD-OUT
V2
VST
N.C.
LND003
1
V1
H2A
CSUB
LND001
LND002
IC003
ICX629EQP-13
7M CCD IMAGER
SUB
CN301
Page 4-5
of Level 3
V9
V10
WGND
17
20 19 18
SY-188
(1/10)
V2
VST
H1B
B
16
N.C.
V8
GND
V10
CCD_OUT
15
A
N.C.
RSS3
V9
14
H2B
13
V8
V5A
V7
12
Note: IC003(CCD imager) and CD-719 flexible complete board are
not supplied, but there are included in CCD block assy.
Note: Voltages of IC003 can not be measured,
because this is mounted by the side of the lens.
V5B
A
V6
V7
CAM_-7.5V_CD
H2A
C
CAM_12.5V_CD
V3B
V4
V5A
V5B
V6
SUB
V7
V3A
D
CSUB
V2
VHLD
VST
V1
V8
V9
V10
E
38 VSUB_CONT
39
VSUB
LND040
STATIC_GND
CD-719 FLEXIBLE BOARD
CCD IMAGER
F
F
05
DSC-W110/W115_L2
4-4
CD-719
Schematic diagrams of the SY-188 board are not shown.
Pages from 4-5 to 4-14 are not shown.
DSC-W110/W115_L2
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
3
2
4
5
6
7
8
AF-112
LND201, LND202
Through the
Harness
(HN-61, HN-62)
LND033
XAF_LED
A
D_3.1V
31P
4
REG_GND
7
STRB_CHG
8
STRB_ON
9
ST_5V
10
STRB_CHG_CONT
11
XSTRB_FULL
12
XAE_LOCK_SW
13
XAE_LOCK_SW
XPWR_ON
14
XPWR_ON
17 16 15 14 13
XSHUT_SW
15
XSHUT_SW
XAE_LOCK_LED
16
XAE_LOCK_LED
XSTRB_LED
17
XSTRB_LED
XPWR_LED
18
XPWR_LED
REG_GND
19
23
1
0
R006
0
C003
XX
D_3.1V
24
D_3.1V
25
D_3.1V
SP-
26
SP-
SP+
27
REG_GND
28
NC
29
VL_3V
30
SW
VCC
F_ON
C001
1u B
CL001
VL_3V
7
0
CHG
XFULL
ST-188
FLEXIBLE
B
FLASH
UNIT
TRIGGER_GND
XE_L
LND036
LND039
C005
0
TRIGGER_GND
0.047u
250V
3.1
Q001
TIG030TS-S-TL-E
FLASH
DRIVE
5
1
8
0
C004
XX
LND031
TRIGGER
-
CL002
31
R003
1M
LND032
N.C
N.C
N.C
6
5
SP+
REG_GND1
IC001
TPS65552RGTR
FLASH CONTROL,
CHARGE CONTROL
LND035
XE_H
LND037
N.C
22
5
PGND
G_IGBT
MIC_GND
PGND
SW
I_PEAK
21
2
REG_GND(MIC_GND)
3
MIC_SIG
XAF_LED
VBATT
3.8
20
REG_GND
C901
315V
62uF
CHARGING
CAPACITOR
3.8
REG_GND1
MIC_SIG
NC
D
T001
HGND
6
+
4
1
N.C
C
REG_GND
LND038
CRF02(TE85R)
4
B
5
D001
C006
220p
50V B
D003
RB520S-40TE61
REG_GND
C002
22u C
6.3V
3
(Pink)
NC
2
R005
4700
HARNESS (HN-059)
3
(Blue)
2
ST_UNREG
HARNESS (HN-060)
ST_UNREG
A
Page 4-16
of Level 2
LND034
L001
2.2uH
10 11 12
1
9
ST_UNREG
C008
4.7u
B
6.3V
CN002
R001
1M
6
2
7
3
8
4
C
270
0
R002
100
D
LND041-LND071
Page 4-18
of Level 2
Note: C901, harness (HN-059) and harness (HN-060)
are not included in ST-180 complete board.
E
E
ST-180 BOARD (1/2)
FLASH DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
F
F
05
DSC-W110/W115_L2
4-15
ST-180 (1/2)
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
2
2
1
4
3
3
4
LCD901(2/2) LCD MODULE
D101
CL-196SYG-CD-T
A
(AE/AF LOCK)
BL_H
A
A
XSTRB_LED
BL_L
LND002
BACKLIGHT
D102
LNJ426W830S0
XPWR_LED
LND001
(FLASH CHARGE/RECORD)
2 S003
D103
CL-196SYG-CD-T
4 S008
1
3
RB001
2200
1
3
5
7
XAE_LOCK_LED
12
Note: LCD901 is not included in
SW-520 complete board.
(POWER)
D_3.1V
3
2
W
1
T
(ZOOM)
LND107
VL_3V
2 S011 1
BT900
VL_3V
LITHIUM
BATTERY
S102
POWER
4
3
2
1
XDIRECT_PB
4
NC
3
BL_L
2
NC
BL_H
3
LND011-LND020
Page 4-18
of Level 2
1
4
3
2
1005X4
1
VDR001
XX
2
B
SW-533
FLEXIBLE
v
(DISP)
3
(2nd)
SHIFT_ON
4
A
CN001
3
2
LND003
STATIC_GND
1
3
5
7
XSHUT_SW
D001
XX
LND102
C
MODE_DIAL2
5
S006
3
1
(1st)
MODE_DIAL1
6
N
4
S101
(SHUTTER)
XAE_LOCK_SW
S012
RB002
2200
2
4
6
8
4
REG_GND
7
MENU
2
XPWR_ON
1
S001
B
B
REG_GND1
2
8
11
4
3
(SLIDESHOW)
1
REG_GND1
KEY_AD2
1
LND106
B
KEY_AD1
9
2
4
6
8
4
10
MIC_GND
MIC_SIG
C
MIC901
MICROPHONE
BLOCK
MIC_GND
MIC_SIG
S004
b
(MACRO)
2
1
C
S007
z
4
S009
B
C
(FLASH)
2
1
3
S010
(MODE DIAL)
4
LND101
3
2
1
4
3
15
LND103
16
SP-
SP+
SP901
SPEAKER
1
SP+
LND104
2
3
SP-
S005
1
V
3
4
4
2
Note: BT900 (lithium battery), MIC901 and
SP901 are not included in ST-180 complete board.
(SELF-TIMER)
1
COM
2
COM
S002
HOME
17
D
D
D
ST-180 BOARD (2/2)
18
AUTO
3
AUTO
4
EASY
5
HIGH SENS
6
SMILE
7
SOFT SNAP
8
LANDSCAPE
9
LANDSCAPE
10
TWILIGHT PORTRAIT
11
SCENE SELECTION
12
MOVIE
13
PROGRAM AUTO
14
1
3
5
7
RB004
2200
2
4
6
8
RB003
2200
2
4
6
8
1
3
5
7
D
Note: S010 (Mode dial) is not supplied,
but this is included in SW-520 complete board.
CONTROL SWITCH
05
1
2
4
3
E
A
ST-180
(1/2)
LND033, LND034
Through the
Harness
(HN-061, HN-062)
Page 4-15
of Level 2
B
E
A
LND201
XAF_LED
LND202
D_3.1V
4
5
6
3
2
1
D201
CL-360S-TD4-X-TL
SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
AF-112 BOARD
F
SW-520 BOARD
F
CONTROL SWITCH
B
XX MARK:NO MOUNT
AF ILLUMINATOR
05
05
DSC-W110/W115_L2
4-16
ST-180 (2/2), AF-112, SW-520
1
2
3
4
5
6
8
7
39P
REG_GND
LND001
A_GND
LND003
V_LINE_OUT
LND005
V_GND
ACV_UNREG
LND010
ACV_UNREG
LND011
ACV_UNREG
LND012
ACV_UNREG
LND013
ACV_UNREG
LND014
BATT_UNREG
LND015
BATT_UNREG
LND016
BATT_UNREG
LND017
BATT_UNREG
SY-188
(10/10)
LND018
BATT_UNREG
CN709
Page 4-14
of Level 3
LND019
BATT_UNREG
LND020
XACV_DET
LND021
UART_Rx
LND022
USB_GND
LND023
USB_DM
LND024
D
Note: CN001 (multi connector) is not supplied, but this is included
in MC-189 flexible complete board.
CN001
(MULTI CONNECTOR)
to AV/USB multi cable
2
HD Pr
HD Pb
USB_VBUS
USB_GND
USB_DP
UART Tx
9
USB_DM
N.C.
USB_GND
N.C.
A_OUT_L
UART Rx
A_GND
CHARGE_V
V_OUT
XACV_DET
25 23 21 19 17 15 13 11
N.C.
LND025
USB_DP
LND026
R004
USB_GND
LND027
USB_VBUS
LND028
UART_Tx
2
LND029
XPOWER_ON
1
LND030
REG_GND
LND031
HD_Pr
LND032
REG_GND
LND033
HD_Pb
LND034
REG_GND
LND035
ACV_GND
LND036
ACV_GND
LND037
ACV_GND
LND038
ACV_GND
LND039
ACV_GND
1k
LF001
4
3
ACV_GND
ACV_GND
ACV_GND
XPOWER_ON
V_GND
CHARGE_V
HD Y
ACV_UNREG
XACC_IN
ACV_UNREG
C
28
C
B
4
B
1
ACV_UNREG
LND009
3
LND008
5
XACC_IN
7
HD_Y
LND007
27
LND006
6
LND004
A
AU_LINE_OUT
8
LND002
26 24 22 20 18 16 14 12 10
A
D
1P
E
E
MC-189 FLEXIBLE BOARD
MULTI CONNECTOR
F
F
05
DSC-W110/W115_L2
4-17
MC-189
1
2
4
3
31P
ST_UNREG
ST_UNREG
LND041
LND030
ST_UNREG
ST_UNREG
LND042
LND029
ST_UNREG
ST_UNREG
LND043
LND028
NC
NC
LND044
LND027
REG_GND
REG_GND
LND045
LND026
REG_GND
REG_GND
LND046
LND025
REG_GND
REG_GND
LND047
LND024
STRB_CHG
STRB_CHG
LND048
LND023
STRB_ON
STRB_ON
LND049
LND022
ST_5V
ST_5V
LND050
LND021
STRB_CHG_CONT
STRB_CHG_CONT
LND051
LND020
XSTRB_FULL
XSTRB_FULL
LND052
LND019
XAE_LOCK_SW
XAE_LOCK_SW
LND053
SY-188
(10/10)
LND018
XPWR_ON
XPWR_ON
LND054
XSHUT_SW
XSHUT_SW
LND055
CN707
Page 4-14
of Level 3
LND017
LND016
XAE_LOCK_LED
XAE_LOCK_LED
LND056
LND015
XSTRB_LED
XSTRB_LED
LND057
LND014
XPWR_LED
XPWR_LED
LND058
LND013
REG_GND
REG_GND
LND059
LND012
MIC_SIG
MIC_SIG
LND060
LND011
REG_GND(MIC_GND)
REG_GND(MIC_GND)
LND061
LND010
REG_GND
REG_GND
LND062
LND009
XAF_LED
XAF_LED
LND063
LND008
D_3.1V
D_3.1V
LND064
LND007
D_3.1V
D_3.1V
LND065
LND006
SP-
SP-
LND066
LND005
SP+
SP+
LND067
LND004
REG_GND
REG_GND
LND068
A
B
1P
LND031
C
LND003
NC
NC
LND069
LND002
VL_3V
VL_3V
LND070
LND001
NC
NC
1P
A
ST-180
(1/2)
CN002
Page 4-15
of Level 2
B
C
LND071
31P
ST-188 FLEXIBLE BOARD
D
D
SY-ST CONNECTION
(PRINTED WIRING BOARD is omitted.)
05
1
2
3
4
1P
A
10P
LND001
KEY_AD1
KEY_AD1
LND020
LND002
KEY_AD2
KEY_AD2
LND019
LND003
REG_GND
REG_GND
LND018
SY-188
(10/10)
LND004
MODE_DIAL1
MODE_DIAL1
LND017
CN706
Page 4-14
of Level 3
LND005
MODE_DIAL2
MODE_DIAL2
LND016
LND006
XDIRECT_PB
XDIRECT_PB
LND015
LND007
NC
NC
LND014
LND008
BL_L
BL_L
LND013
LND009
NC
NC
LND012
LND010
BL_H
BL_H
10P
B
A
SW-520
CN001
Page 4-16
of Level 2
LND011
1P
SW-533 FLEXIBLE BOARD
B
SY-SW CONNECTION
(PRINTED WIRING BOARD is omitted.)
05
DSC-W110/W115_L2
4-18
ST-188, SW-533
4-3. PRINTED WIRING BOARDS
Link
CD-719 FLEXIBLE BOARD
SW-520 BOARD
ST-180 BOARD
MC-189 FLEXIBLE BOARD
AF-112 BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
DSC-W110/W115_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
(ENGLISH)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
• Chip parts.
Transistor
•
•
: Uses unleaded solder.
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
B
(JAPANESE)
プリント図共通ノート
【プリント図ノート】
・
・
：無鉛半田を使用しています。
：基板
：フレキシブル配線板
見ている面側のパターン。
：裏側のパターン
（他のパターンについては表示されていません）
・スルーホールは省略。
・プリント図には，本機で使用していない部品が記載されている
場合があります。
・Cはパネル表示名称。
DSC-W110/W115_L2
4-19
Diode
6 5 4 4 5 6 5
C
E
4 4
3
5
3
3
1 23
1 2 3 3 2 1 1 2 3 3 2 1
2
1 2
1 2
1
4
3
3
4 6 5 4 4 5 6
2
1 1 2 3 3 2 1
2 2
1 3
2
5 4 3 3 4 5 4
1
1
2
3
2
4
1
1 6 54
CD-719 (2 layers)
: Uses unleaded solder.
CD-719 FLEXIBLE BOARD
1
39
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
LND010
LND011
LND012
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND024
LND025
LND026
LND027
LND028
LND029
LND030
LND031
LND032
LND033
LND034
LND035
LND036
LND037
LND038
LND039
917-DC
<IP>
12
5
13
C003
4
C009
1
IC003
C005
LND040
20
29
21
28
1-874-424-
05
11
Note: IC003 (CCD imager) and CD-719 flexible complete board
are not supplied, but there are included in CCD block assy.
DSC-W110/W115_L2
4-20
CD-719
Printed wiring board of the SY-188 board is not shown.
Page from 4-21 is not shown.
DSC-W110/W115_L2
ST-180 (4 layers), AF-112 (2 layers)
: Uses unleaded solder.
MIC901
MICROPHONE
BLOCK
ST-180 BOARD (SIDE A)
2
12
16
4
D201
3
HARNESS (HN-062) (Gray)
HARNESS (HN-061) (Yellow)
D201
SELF-TIMER/
SMILE SHUTTER/
AF ILLUMINATOR
C005
8
L001
R003
CL002
8
5
4
6
R001
R002
<WG PE>
211-FA
AF-112 BOARD
4
D101
(AE/AF LOCK)
C001
C003
C002
C004
R006
5
Q001
+
LND034 LND033
05
1
1
D101
LND038
HARNESS (HN-059) (Pink)
9
1
R005
17
2
LND037
IC001
4
1
C006
13
C008
D003
D103
(POWER)
C901
CHARGING
CAPACITOR
S101
S102
LND102
HARNESS (HN-060) (Blue)
(SHUTTER)
1
3
LND101
4
Orange
White
POWER
3
1-874-411-
21
Note: Harness (HN-061) and harness (HN-062) are not included
in AF-112 complete board and ST-180 complete board.
B
Y
G
LND202
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
LND201
05
1-874-413-
11
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
Note: BT900 (lithium battery), C901, MIC901, SP901, harness (HN-059)
and harness (HN-060) are not included in ST-180 complete board.
BT900
BATTERY,
LITHIUM SECONDARY
ST-180 BOARD (SIDE B)
D102
FLASH CHARGE/
RECORD
LND107
D102
CL001
LND106
LND031
LND032
31
1
CN002
30
2
LND103 LND104
Red
Black
2
LND039
1
T001
LND036
3
LND035
05
K
4
D001
A
1-874-411SP901
SPEAKER
TRIGGER
21
TRIGGER_GND
XE_L
XE_H
FLASH UNIT
DSC-W110/W115_L2
4-22
ST-180, AF-112
SW-520 (2 layers)
: Uses unleaded solder.
SW-520 BOARD (SIDE B)
SW-520 BOARD (SIDE A)
S003
3
2
4
1
T
(ZOOM)
LND001
S010
(MODE DIAL)
LND002
11
BL-L
1
TO LCD901
(BACKLIGHT)
1
3
4
2
W
BL-H
S008
S001
1
15
CN001
10
12
1
RB0032
8
11 10
18
9
3
Note: S010 (Mode dial) is not supplied, but this is
included in SW-520 complete board.
1
2
3
D001
MENU
3
7
6
5
4
16
14 13 2 12
7
8
RB004
S010
1
2
1
7
RB001
1
2
8
7
17
8
VDR001
HOME
v
(DISP)
4
S002
3
4
1
2
2
4
S006
2
3
7
RB002
b
(MACRO)
1
2
8
1
S004
1
LND003
2
4
2
B
(FLASH)
z
2
S007
S009
1
3
4
3
4
1
3
V
(SELF-TIMER)
1
S005
N
3
2
4
3
1
S012
2
3
1
S011
4
(SLIDESHOW)
2
4
1-874-412-
11
05
05
DSC-W110/W115_L2
4-23
1-874-412-
11
SW-520
MC-189 (2 layers)
: Uses unleaded solder.
MC-189 FLEXIBLE BOARD
(MULTI CONNECTOR)
28
26
2
CN001
27
1
25
39
LND038 LND039
LND037
LND036
LND035
LND034
LND033
LND032
LND031
LND030
LND029
LND028
LND027
LND026
LND025
LND024
LND023
LND022
LND021
LND020
LND019
LND018
LND017
LND016
LND015
LND014
LND013
LND012
LND011
LND010
LND009
LND008
LND007
LND006
LND005
LND004
LND003
LND002 LND001
1
Note: CN001 (multi connector) is not supplied,
but this is included in MC-189 flexible complete board.
R004
4
2
3
1
LF001
MC-189
1-874-415-
11
05
DSC-W110/W115_L2
4-24E
MC-189
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
EXPLODED VIEWS
Link
A
B
LCD SECTION
C
BT HOLDER SECTION
FRONT SECTION
D
E
CABINET (UPPER) SECTION
Link
LENS SECTION
ELECTRICAL PARTS LIST
AF-112 BOARD
D
MC-189 FLEXIBLE BOARD C
CD-719 FLEXIBLE BOARD
B
ST-180 BOARD
DSC-W110/W115_L2
D
ACCESSORIES
SW-520 BOARD
A
Ver. 1.1 2008.05
The changed portions from
Ver. 1.0 are shown in blue.
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金
被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
•
Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
TW : Taiwan model
TH : Thai model
DSC-W110/W115_L2
5-1
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定してください。
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重要な部品です。
従って交換時は，
必ず指定の部品を使用してください。
• 外装部品色表示
例：
(SILVER):セットの色を表す。
(Silver) : 部品の色を表す。
5. REPAIR PARTS LIST
DISASSEMBLY
5-1. EXPLODED VIEWS
HARDWARE LIST
5-1-1. LCD SECTION
10
ns: not supplied
9
(Note)
#20
#20
14
8
13
ns
LCD901
11
#20
#118
12
7
5
#20
4
6
1
3
#20
Front Section
(See page 5-3)
2
#20
Note: LCD窓接着紙KITを交換する際は，「HELP1: LCD
Window Adhesive Sheet Kit」を参照してください。
Note: Refer to “HELP 1: LCD Window Adhesive Sheet Kit”
when replace the LCD window adhesive sheet kit.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
2
3
* 4
* 5
3-289-769-01
3-289-776-01
3-289-757-01
3-289-782-01
3-289-763-01
CABINET (L), SIDE
CABINET (R), SIDE
SCREW, TRIPOD
SHEET, LCD FLEXIBLE FIXED
SHEET, LCD INSULATING
9
10
11
12
* 13
3-289-745-01
3-289-766-01
1-875-540-11
A-1494-316-A
3-289-767-01
SHEET KIT, LCD WINDOW ADHESIVE (Note)
WINDOW, LCD
SW-533 FLEXIBLE BOARD
SW-520 BOARD, COMPLETE
SHEET, ZOOM BLIND
* 6
* 7
8
8
8
3-289-759-01
3-093-800-01
X-2188-895-1
X-2188-896-1
X-2188-897-1
FRAME, LCD
GASKET (230)
CABINET (REAR (110SL)) ASSY (W110: Silver)
CABINET (REAR (110BK)) ASSY (W110: Black)
CABINET (REAR (115BK)) ASSY (W115)
3-289-762-01
8-753-296-94
2-635-591-31
2-655-580-01
DIAL, MODE
ACX358AKR-3
SCREW (M1.4), NEW TRUSTAR P2 (Silver)
SCREW 0+P2 M1.4 NEWTRU-STAR (Black)
14
LCD901
#20
#118
DSC-W110/W115_L2
5-2
5. REPAIR PARTS LIST
DISASSEMBLY
HARDWARE LIST
5-1-2. FRONT SECTION
BT Holder Section
(See page 5-4)
53
54
(including IC003 (CCD imager) and
CD-719 flexible complete board) (Note 1, 2)
55
#30
52
#20
51
Lens Section
(See page 5-6)
Note 1: Be sure to read “Precuations for Replacement of
Imager” on page 4-2.
Note 1: イメージャの交換時は4 - 3 ページの イメージャ
交換時の注意 を必ずお読みください。
Note 2: There are two types of modules used in the CCD
BLOCK ASSY.
They are interchangeability and only one type is
available for repair part.
Note 2: 2種類のCCD部組が使用されています。
修理部品は1 種類しか用意していませんが，それ
らには互換性があります。
Ref. No.
51
51
52
* 53
54
Part No.
Description
X-2188-883-1 CABINET (FRONT (7.2SL)) ASSY (W110: Silver)
X-2188-884-1 CABINET (FRONT (7.2BK)) ASSY
(W110: Black/W115)
3-289-768-01 WINDOW, OVF
3-289-781-01 TAPE (AF)
A-1543-224-A SERVICE, CCD BLOCK ASSY
(including IC003 (CCD imager) and
CD-719 flexible complete board) (Note 1, 2)
Ref. No.
Part No.
* 55
#20
#30
3-289-764-01 GASKET (280)
2-635-591-31 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
3-086-156-11 SCREW B1.2 (White)
DSC-W110/W115_L2
5-3
Description
5. REPAIR PARTS LIST
DISASSEMBLY
HARDWARE LIST
5-1-3. BT HOLDER SECTION
114
ns: not supplied
109
BT903
(Note) BT902
(Note)
#3
106 107
108
105
Cabinet (Upper) Section
(See page 5-5)
ns
111
104
#20
BT901
(Note)
110
112
ns
ns
113
103
101
102
Note: Refer to “HELP 7: Installation method of battery terminal
board” when changing the battery terminal board.
Note: バッテリ端子板を交換する際は，「HELP 7: Installation
method of battery terminal board」を参照してください。
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
101
* 102
* 102
* 103
X-2188-901-1
X-2188-902-1
3-288-271-01
3-288-271-11
3-288-272-01
HOLDER (SL) ASSY, BT (W110: Silver)
HOLDER (BK) ASSY, BT (W110: Black/W115)
LID, BT (W110: Silver)
LID, BT (W110: Black/W115)
PLATE, BT HINGE
110
* 111
112
* 113
A-1512-919-A
3-289-783-01
A-1494-320-A
3-289-758-01
SY-188 BOARD, COMPLETE (SERVICE)
SHEET (SY), RADIATION
MC-189 FLEXIBLE BOARD, COMPLETE
SHEET METAL, MULTI FIXED
* 104
* 105
106
107
108
3-289-756-01
3-292-292-01
1-965-766-11
1-965-767-11
1-965-768-11
LID, DC
CUSHION, ST LIGHT INTERCEPTION
HARNESS (HN-067) (Red)
HARNESS (HN-068) (White)
HARNESS (HN-069) (Black)
* 114
BT901
BT902
BT903
#3
3-298-230-01
1-780-456-21
1-780-456-21
1-780-456-21
2-660-401-01
TAPE (N2)
TERMINAL BOARD, BATTERY (Note)
TERMINAL BOARD, BATTERY (Note)
TERMINAL BOARD, BATTERY (Note)
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
#20
109
1-874-856-11 ST-188 FLEXIBLE BOARD
DSC-W110/W115_L2
5-4
2-635-591-31 SCREW (M1.4), NEW TRUSTAR P2 (Silver)
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-4. CABINET (UPPER) SECTION
ns: not supplied
157
165
164
SP901
MIC901
158
159
160
152
161
154
ns
(Note)
151
162
153
155
C901
(Note)
#5
156
BT900
! : BT900
(LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
163
(See page 4-22)
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Note: Refer to “HELP 6: Sheets and Harness of ST-180 Board” when
replace harness (HN-059/060).
Note: ハーネス（HN-059/060）を交換する際は，「HELP 6: Sheets
and Harness of ST-180 Board」を参照してください。
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
0*152
153
154
* 155
A-1540-552-A
1-480-556-11
1-965-681-11
1-965-680-11
3-289-779-01
ST-180 BOARD, COMPLETE
FLASH UNIT
HARNESS (HN-060) (Blue) (Note)
HARNESS (HN-059) (Pink) (Note)
SHEET, LITHIUM INSULATING
* 161
162
* 163
* 164
* 165
3-289-761-01
A-1494-317-A
3-289-760-01
3-878-693-01
3-398-835-01
RETAINER, AF
AF-112 BOARD, COMPLETE
HOLDER, CAPACITOR
TAPE (ST)
SHEET (260), ST INSULATING
* 156
157
158
159
* 160
3-289-778-01
X-2188-898-1
1-965-683-11
1-965-682-11
3-289-765-01
SHEET, ST INSULATING
CABINET (UPPER (SL/BK)) ASSY
HARNESS (HN-062) (Gray)
HARNESS (HN-061) (Yellow)
SHEET, CAPACITOR PROTECTION
0 BT900
0*C901
MIC901
SP901
#5
1-756-710-12
1-114-606-11
1-542-721-21
1-826-403-41
3-080-204-01
LITHIUM RECHARGEABLE BATTERY
ELECT
62uF
315V
MICROPHONE BLOCK
LOUDSPEAKER (1.0CM)
SCREW, TAPPING, P2 (Black)
DSC-W110/W115_L2
5-5
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-5. LENS SECTION
ns: not supplied
#30
(Note 4)
201
(Note 1)
ns
#30
(Note 4)
205
ns
209
204
#30
(Note 4)
(Note 2)
(Note 3)
203
202
(Note 2)
208
(Note 3)
(Note 2)
206
(Note 3)
207
(Note 3)
Note 1: Refer to “2-3. Precuations when Holding the Lens
Block” on page 2-6 when detach or replace the lens
block.
Note 3: Refer to “2-5. Lens Motor Replacing Method” on
page 2-8 when replace the zoom gear block or the
optical stepping motor.
Note 1: レンズブロックを取外し又は交換する際は，2 - 6
ページの「2-3. Precautions when Holding the Lens
Block」を参照してください。
Note 3: ズームギアブロック又は光学ステッピングモー
タを交換する際は，2-8ページの「2-5. Lens Motor Replacing Method」を参照してください。
Note 2: Refer to “2-4. Barrier Assy Replacing Method” on
page 2-7 when replace the barrier assy.
Note 4: Tightening torque = 0.049 ± 0.01 N•m (0.5 ± 0.1
kgf•cm)
Note 2: バリア組立を交換する際は，2 - 7 ページの「2 - 4 .
Barrier Assy Replacing Method」を参照してくだ
さい。
Note 4: 締め付けトルク＝0 . 0 4 9 ± 0 . 0 1 N • m （0 . 5 ± 0 . 1
kgf•cm）
Ref. No.
201
202
203
204
205
Part No.
Description
8-848-833-01
3-268-546-13
2-691-890-11
A-1437-489-A
1-788-635-11
LSV-1250B (Note 1)
RING A (S), ORNAMENTAL (Note 2)
TAPE, BARRIER (Note 2)
BARRIER ASSY (SDPW) (Note 2)
FINDER, OPTICAL (1250)
Ref. No.
206
207
208
209
#30
DSC-W110/W115_L2
5-6
Part No.
Description
X-2187-865-1
3-268-545-01
1-480-381-11
1-787-672-11
3-086-156-11
GEAR (S), NARUTO (Note 3)
PLATE SPRING, FG (Note 3)
GEAR BLOCK, ZOOM (1250) (Note 3)
STEPPING MOTOR, OPTICAL (F1250) (Note 3)
SCREW B1.2 (White) (Note 4)
AF-112
CD-719
MC-189
ST-180
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
Part No.
A-1494-317-A AF-112 BOARD, COMPLETE
**********************
Description
< CONNECTOR >
* CN002
1-817-391-81 CONNECTOR, FPC (ZIF) 31P
< DIODE >
< DIODE >
* D201
6-501-861-01 DIODE CL-360S-TD4-X-TL (SELF-TIMER/
SMILE SHUTTER/AF ILLUMINATOR)
A-1543-224-A SERVICE, CCD BLOCK ASSY (Note 1, 2)
(Not supplied) CD-719 FLEXIBLE BOARD, COMPLETE
*******************************
(IC003 (CCD imager) and CD-719 flexible complete board are not supplied,
but there are included in CCD block assy.)
0 D001
D003
D101
* D102
D103
1-114-582-11 CERAMIC CHIP
1-125-777-11 CERAMIC CHIP
1-114-582-11 CERAMIC CHIP
IC001
0.1uF
0.1uF
0.1uF
10%
10%
10%
16V
10V
16V
CRF02 (TE85R)
RB520S-40TE61
CL-196SYG-CD-T (AE/AF LOCK)
LNJ426W830S0
(FLASH CHARGE/RECORD)
6-500-594-01 DIODE CL-196SYG-CD-T (POWER)
6-707-555-01 IC TPS65552RGTR
< COIL >
* L001
1-400-820-11 INDUCTOR
2.2uH
< TRANSISTOR >
< IC >
IC003
DIODE
DIODE
DIODE
DIODE
< IC >
< CAPACITOR >
* C003
C005
* C009
6-501-096-01
6-500-619-01
6-500-594-01
6-502-311-01
(Not supplied) ICX629EQP-13 (Note 1)
(IC003 is supplied including in the CCD block assy.)
0*Q001
6-551-686-01 TRANSISTOR
TIG030TS-S-TL-E
< RESISTOR >
A-1494-320-A MC-189 FLEXIBLE BOARD, COMPLETE
*******************************
(CN001 (multi connector) is not supplied, but
this is included in MC-189 complete board.)
R001
R002
0 R003
R005
R006
1-218-989-11
1-218-941-81
1-216-121-11
1-218-863-11
1-218-990-81
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
SHORT CHIP
1M
100
1M
4.7K
0
5%
5%
5%
0.5%
1/16W
1/16W
1/10W
1/10W
< CONNECTOR >
< SWITCH >
CN001
(Not supplied) CONNECTOR, MULTIPLE (SOCKET)
(MULTI CONNECTOR)
(CN001 (multi connector) is supplied including
in MC-189 flexible complete board.)
S101
S102
1-786-819-22 TACTILE SWITCH (SHUTTER)
1-771-844-21 SWITCH, TACTILE (SMD) (POWER)
< TRANSFORMER >
< LINE FILTER >
0 T001
LF001
< RESISTOR >
R004
1-218-953-11 RES-CHIP
1K
5%
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
1/16W
A-1540-552-A ST-180 BOARD, COMPLETE
***********************
(BT900 (lithium battery) is not included in ST-180 complete board.)
0*
Note 1: Be sure to read “Precuations for Replacement of
Imager” on page 4-2.
1-756-710-12 LITHIUM RECHARGEABLE BATTERY
Note 1: イメージャの交換時は4 - 3 ページの イメージャ
交換時の注意 を必ずお読みください。
< CAPACITOR >
C001
C002
0 C005
C006
* C008
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
1-480-556-11 FLASH UNIT
< BATTERY >
0 BT900
1-445-108-21 TRANSFORMER, D.C-D.C CONVERTER
1-457-223-11 COMMON MODE CHOKE COIL
1-112-717-91
1-100-611-91
1-100-758-11
1-164-933-11
1-112-746-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
22uF
0.047uF
220PF
4.7uF
10%
20%
10%
10%
10%
6.3V
6.3V
250V
50V
6.3V
Note 2: There are two types of modules used in the CCD
BLOCK ASSY.
They are interchangeability and only one type is
available for repair part.
Note 2: 2種類のCCD部組が使用されています。
修理部品は1 種類しか用意していませんが，それ
らには互換性があります。
• Refer to page 5-1 for mark 0.
DSC-W110/W115_L2
5-7
SW-520
Ref. No.
Part No.
Description
Ref. No.
A-1494-316-A SW-520 BOARD, COMPLETE
***********************
(S010 (Mode dial) is not supplied, but this is
included in SW-520 complete board.)
< CONNECTOR >
* CN001
1-820-634-51 CONNECTOR, FPC (LIF (NON-ZIF))
< COMPOSITION CIRCUIT BLOCK >
RB001
RB002
RB003
RB004
1-234-376-11
1-234-376-11
1-234-376-11
1-234-376-11
RES, NETWORK
RES, NETWORK
RES, NETWORK
RES, NETWORK
2.2K (1005X4)
2.2K (1005X4)
2.2K (1005X4)
2.2K (1005X4)
< SWITCH >
*
*
*
*
*
S001
S002
S003
S004
S005
*
*
*
*
S006
S007
S008
S009
S010
* S011
* S012
1-786-914-31
1-786-914-31
1-786-914-31
1-786-914-31
1-786-914-31
SWITCH, TACTILE (MENU)
SWITCH, TACTILE (HOME)
SWITCH, TACTILE (W (ZOOM))
SWITCH, TACTILE (b (MACRO))
SWITCH, TACTILE (V (SELF-TIMER))
1-786-914-31 SWITCH, TACTILE (v (DISP))
1-786-914-31 SWITCH, TACTILE (z)
1-786-914-31 SWITCH, TACTILE (T (ZOOM))
1-786-914-31 SWITCH, TACTILE (B (FLASH))
(Not supplied) ROTARY SWITCH (MODE DIAL)
(S010 (Mode dial) is supplied including in SW-520 complete board.)
1-786-914-31 SWITCH, TACTILE (SLIDESHOW)
1-786-914-31 SWITCH, TACTILE (N)
Electrical parts list of the SY-188 board is
not shown.
Page 5-9 to 5-12 are not shown.
DSC-W110/W115_L2
5-8
Part No.
Description
Ver. 1.1 2008.05
The changed portions from
Ver. 1.0 are shown in blue.
Checking supplied accessories.
Note: This item is supplied with the unit as an accessory, but is
not prepared as a service part.
Battery Charger
Battery Charger
BC-CSGB/BC-CSGC
BC-CSGB/BC-CSGC
0 1-480-175-11 (J)
0 1-480-175-31
0 1-480-175-21 (US, CND)
(EXCEPT US, CND, J)
Wrist Strap
2-050-981-01
Power Cord
0 1-555-074-91 (AUS)
0 1-783-952-61 (AR)
0 1-824-910-71 (AEP, E)
0 1-832-121-31 (CH)
0 1-827-269-12 (UK)
0 1-833-892-21 (KR)
0 1-835-434-11 (TH)
Conversion (2P) Adaptor
0 1-569-008-12 (E: NTSC)
USB, A/V Cable for
Multi-use Terminal
1-834-813-11
CD-ROM
“Cyber-shot application software”
“Cyber-shot Handbook”
“Cyber-shot Step-up Guide”
3-452-469-02 (EXCEPT J)
3-452-939-01 (J)
Soft Carrying Case
3-291-623-01 (W115)
Rechargeable Battery Pack
NP-BG1
(Note)
Battery Case
(Note)
Cyber-shot Handbook (PDF)
The CD-ROM supplied contains all of language version of
the Cyber-shot Handbook (PDF) for printing.
・ The printed matter is not supplied. If required, please
order it with the part number below.
・ (Only for destination Japanese model)
日本国内については日本語のみが印刷での部品供給
可能です。
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Instruction Manual
3-700-780-01 (JAPANESE) (J)
3-700-780-11 (ENGLISH) (CND, AEP, UK, E, AUS, TH)
3-700-780-21 (FRENCH, ITALIAN) (CND, AEP)
3-700-780-31 (SPANISH, PORTUGUESE) (AEP, E, AR)
3-700-780-41 (GERMAN, DUTCH) (AEP)
3-700-780-51 (TRADITIONAL CHINESE,
SIMPLIFIED CHINESE) (E)
3-700-780-61 (RUSSIAN, UKRAINIAN) (AEP)
3-700-780-71 (ARABIC, PERSIAN) (E)
3-700-780-81 (KOREAN) (KR)
3-700-780-91 (POLISH, CZECH) (AEP)
3-700-781-11 (HUNGARIAN, SLOVAK) (AEP)
3-700-781-21 (SWEDISH, FINNISH) (AEP)
3-700-781-31 (NORWEGIAN, DANISH) (AEP)
3-700-781-41 (THAI, MALAY) (E)
3-700-781-51 (TURKISH, GREEK) (AEP)
3-700-781-61 (ENGLISH, SPANISH) (US)
3-700-781-71 (SIMPLIFIED CHINESE) (CH)
3-700-781-81 (THAI) (TH)
3-700-777-01
3-700-777-11
3-700-777-21
3-700-777-31
3-700-777-41
3-700-777-51
3-700-777-61
3-700-777-71
3-700-777-81
3-700-777-91
3-700-778-11
3-700-778-21
3-700-778-31
3-700-778-41
3-700-778-51
3-700-778-61
3-700-778-71
3-700-778-81
3-700-778-91
3-700-779-11
3-700-779-21
3-700-779-31
3-700-779-41
3-700-779-51
3-700-779-61
3-700-779-71
3-700-779-81
(JAPANESE)
(ENGLISH)
(FRENCH)
(ITALIAN)
(SPANISH)
(PORTUGUESE)
(GERMAN)
(DUTCH)
(TRADITIONAL CHINESE)
(SIMPLIFIED CHINESE)
(RUSSIAN)
(ARABIC)
(PERSIAN)
(KOREAN)
(POLISH)
(CZECH)
(HUNGARIAN)
(SLOVAK)
(SWEDISH)
(FINNISH)
(NORWEGIAN)
(DANISH)
(THAI)
(MALAY)
(TURKISH)
(GREEK)
(UKRAINIAN)
• Refer to page 5-1 for mark 0.
DSC-W110/W115_L2
5-13E
HARDWARE LIST (1/7)
#1: M1.7 X 2.5
(Black)
2-635-562-11
#2: M1.7 X 4.0
(Black)
2-635-562-31
#3: M1.7 X 2.5
(Red)
2-660-401-01
1.7
2.5
1.7
4.0
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
1.7
4.0
#13: M1.7 X 2.5 (Tapping)
(Silver)
3-085-397-01
1.7
1.7
2.5
#16: M1.4 X 2.5
(Silver)
2-586-337-01
2.5
#19: M1.2 X 4.0 (Tapping)
(Red)
3-086-156-21
1.4
1.5
2.5
1.4
1.4
1.5
#18: M1.4 X 2.5
(Silver)
2-635-591-21
1.7 2.2
1.7
5.0
#15: M1.4 X 1.5
(Silver)
3-062-214-01
1.7
#17: M1.7 X 1.5
(Silver)
2-586-389-01
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
4.0
#14: M1.7 X 2.5
(Silver)
2-599-475-11
2.5
3.5
1.6
#10: M1.7 X 4.0
(Silver)
2-599-475-31
1.7
1.7
1.7
5.0
#8: M1.7 X 3.5 (Tapping)
(Silver)
3-078-890-01
1.4
3.5
1.4
2.5
#7: M1.7 X 1.6
(Black)
7-627-552-18
1.7
3.5
1.7
2.5
#6: M1.4 X 1.7
(Silver)
2-598-474-01
#9: M1.7 X 5.0 (Tapping)
(Silver)
3-078-890-21
#4: M1.4 X 2.5 (Tapping)
(Dark Silver)
3-348-998-81
#20: M1.4 X 3.0
(Silver)
2-635-591-31
1.4
1.2
4.0
3.0
HARDWARE LIST (2/7)
#21: M1.4 X 3.0
(Black)
2-662-396-21
#22: M1.7 X 5.0 (Tapping)
(Silver)
3-083-261-01
#23: M1.7 X 4.0 (Tapping)
(Black)
3-080-204-11
1.7
1.4
5.0
3.0
#25: M1.7 X 3.0
(Black)
2-635-562-21
3.0
3.0
#36: M3.0 X 6.0
(Silver)
4-886-821-11
3.0
4.0
6.0
6.0
#38: M3.0 X 20.0 (Tapping)
(Silver)
7-685-651-79
2.0
4.5
#35: M4.0 X 6.0 (Tapping)
(Silver)
3-975-291-02
8.0
#37: M2.0 X 6.0 (Tapping)
(Black)
3-080-206-31
3.0
4.0
#34: M3.0 X 8.0
(Black)
3-077-331-41
6.0
#32: M2.0 X 4.5 (Tapping)
(Silver)
2-102-498-01
1.2
3.5
#33: M3.0 X 6.0
(Silver)
3-077-331-21
4.0
#31: M3.0 X 4.0
(Silver)
2-102-434-01
1.4
1.4
1.4
2.0
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
2.5
#28: M1.4 X 4.0 (Tapping)
(Silver)
3-348-998-61
1.4
2.0
#29: M1.4 X 2.5
(Black)
2-662-396-01
5.5
#27: M1.4 X 2.0
(Black)
2-662-396-11
1.7
1.7
1.7
4.0
#26: M1.4 X 2.0
(Silver)
2-635-591-11
3.0
#24: B1.7 X 5.5 (Tapping)
(Black)
4-679-805-11
#39: M2.6 X 5.0 (Tapping)
(Black)
7-685-791-09
#40: M2.0 X 4.0 (Tapping)
(Silver)
7-685-851-04
3.0
2.0
6.0
2.6
20.0
5.0
2.0
4.0
HARDWARE LIST (3/7)
#41: M3.0 X 8.0 (Tapping)
(Silver)
3-065-748-01
#42: M2.0 X 4.0 (Tapping)
(Silver)
7-628-253-00
#43: M1.7 X 4.0
(Red)
2-660-401-31
3.0
8.0
2.0
#46: M1.7 X 3.0
(Red)
2-660-401-11
1.7
3.0
#49: M2.0 X 4.0
(Black)
2-630-005-31
2.0
4.0
#48: M1.7 X 2.5
(Silver)
3-973-497-91
1.7
1.4
2.5
3.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
1.7
3.0
#47: M1.4 X 3.0 (Tapping)
(Silver)
2-665-774-01
1.4
2.5
1.7
4.0
4.0
#45: M1.4 X 2.5
(Silver)
2-587-151-01
#44: M1.7 X 3.0 (Tapping)
(Silver)
3-078-890-61
#51: M2.0 X 2.5
(Silver)
3-073-686-01
#52: M2.0 X 4.0 (Tapping)
(Black)
3-080-206-11
2.0
2.0
2.0
4.0
3.0
2.5
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
6.0
5.0
#57: M1.7 X 4.0
(Black)
7-627-852-18
#56: M2.0 X 3.5
(Silver)
3-067-187-11
1.75
2.0
2.0
4.0
#58: M2.0 X 6.0 (Tapping)
(Silver)
3-719-408-11
6.0
2.0
3.5
#59: M2.0 X 5.0 (Tapping)
(Silver)
3-080-205-21
2.0
1.7
4.0
#55: M2.0 X 4.0
(Silver)
2-655-582-11
#54: M1.75 X 6.0 (Tapping)
(Black)
3-318-203-11
#60: M2.6 X 5.0
(Black)
3-061-062-11
2.6
2.0
5.0
5.0
HARDWARE LIST (4/7)
#61: M3.0 X 10.0
(Black)
7-682-549-09
#62: M2.0 X 3.0
(Silver)
3-080-202-21
3.0
10.0
2.0
12.5
#66: M1.4 X 1.4
(Silver)
2-635-591-41
1.4
3.5
2.0
4.0
3.5
3.5
#76: M1.7 X 4.0 (Tapping)
(Silver)
2-666-551-11
1.7
4.0
#79: M1.4X 2.0
(Silver)
2-587-151-11
#80: M1.4X 2.0
(Black)
3-279-411-01
1.4
1.4
1.2
2.0
1.7
1.7
#78: M1.4 X 3.5
(Red)
3-208-537-11
1.4
1.4
#75: M1.7 X 3.5 (Tapping)
(Silver)
2-666-551-01
6.0
#77: M1.2 X 5.0 (Tapping)
(Silver)
3-086-156-31
#72: M1.4 X 2.0
(Silver)
4-663-621-41
2.0
#74: M1.7 X 6.0 (Tapping)
(Silver)
2-666-551-31
1.7
4.0
#71: M1.4 X 2.0
(Red)
3-208-537-01
5.0
1.2
5.0
1.4
1.7
1.7
#73: M1.2 X 4.0 (Tapping)
(Black)
3-086-156-61
#68: M1.7 X 4.0
(Silver)
2-655-581-01
1.4
#70: M1.7 X 5.0
(Silver)
2-599-475-41
3.0
5.0
#67: M1.4 X 2.0
(Silver)
3-389-523-16
1.4
#69: M1.7 X 3.0
(Silver)
2-599-475-21
1.7
5.0
3.0
#65: M1.4 X 3.5
(Silver)
2-635-591-01
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
#63: M5.0 X 12.5
(Black)
3-060-811-21
2.0
1.4
2.0
HARDWARE LIST (5/7)
#83: M1.7 X 7.0 (Tapping)
(Black)
3-080-204-41
#82: M1.4 X 1.4
(Silver)
3-272-251-01
#81: M1.7 X 2.5
(Silver)
2-515-756-01
1.4
1.7
2.5
2.5
#90: M1.7 X 3.0
(Silver)
3-271-395-01
#91: M1.7 X 3.0 (Tapping)
(Silver)
2-695-434-11
3.0
#97: M1.4 X 2.5
(Black)
2-662-396-31
1.4
1.4
3.0
2.5
#99: M2.5 X 6.0 (Tapping)
(Silver)
3-776-750-02
3.8
8.0
#96: M1.4 X 2.5
(Silver)
2-587-151-21
8.0
#98: M3.0 X 8.0
(Silver)
3-077-331-01
2.5
3.9
#95: M3.0 X 8.0 (Tapping)
(Black)
7-685-646-79
4.0
3.5
2.0
1.7
1.7
1.7
#92: M2.0 X 3.9
(Black)
3-268-954-01
3.5
#94: M1.7 X 4.0
(Black)
2-515-483-31
1.6
5.9
1.7
2.0
#93: M1.7 X 3.5 (Tapping)
(Silver)
3-254-082-01
1.6
5.3
4.0
5.0
#88: M1.6 X 5.9 (Tapping)
(Silver)
2-689-015-01
1.7
1.7
2.0
3.0
#87: M1.6 X 5.3
(Black)
2-689-328-01
#86: M1.7 X 4.0 (Tapping)
(Silver)
2-695-434-21
#89: M2.0 X 5.5 (Tapping)
(Silver)
2-695-575-01
1.7
7.0
1.4
#85: M1.7 X 2.5
(Black)
2-515-483-11
#84: M2.0 X 3.0
(Silver)
3-072-453-11
#100: M2.0 X 6.0
(Black)
3-080-203-51
2.5
6.0
2.0
6.0
HARDWARE LIST (6/7)
#102: M2.6 X 8.0
(Black)
7-621-284-30
#101: M2.0 X 5.0
(Silver)
7-621-555-39
2.6
2.0
5.0
#105: M2.0 X 4.0
(Red)
2-891-494-31
10.0
#106: M2.0 X 6.0
(Black)
3-713-786-11
#107: M2.0 X 5.0
(Silver)
3-032-750-01
2.0
4.0
6.0
#109: M1.7 X 3.0
(Black)
2-515-483-21
#110: M2.0 X 3.0
(Black)
2-630-005-21
5.0
#117: M1.7 X 4.5 (Tapping)
(Silver)
2-695-429-31
#115: M1.4 X 3.5 (Tapping)
(Silver)
3-348-998-51
1.4
#116: M2.0 X 3.5 (Tapping)
(Silver)
2-695-435-01
2.0
1.4
3.5
#119: M2.6 X 5.0
(Black)
7-627-556-58
1.4
2.0
#112: M1.4 X 5.0
(Black)
2-178-410-11
5.0
3.5
#118: M1.4 X 2.0
(Black)
2-655-580-01
1.7
3.0
4.0
5.5
1.7
1.7
2.0
1.7
#108: M1.7 X 3.0 (Tapping)
(Black)
2-695-430-01
#111: M1.7 X 4.0 (Tapping)
(Black)
2-887-124-01
#114: M2.0 X 5.5 (Tapping)
(Silver)
2-698-464-01
#113: M1.7 X 5.0
(Black)
2-635-562-41
8.0
5.0
3.0
3.0
3.0
2.0
2.0
1.7
#104: M3.0 X 8.0
(Black)
7-682-548-09
2.6
8.0
2.0
4.5
#103: M2.6 X 10.0
(Silver)
7-685-794-09
#120: M2.6 X 6.0
(Silver)
7-621-770-67
2.6
2.6
5.0
6.0
HARDWARE LIST (7/7)
#121: M2.0 X 4.0 (Tapping)
(Silver)
3-080-205-11
#122: M3.0 X 6.0
(Black)
7-682-547-09
#123: M4.0 X 8.0
(Black)
7-682-561-09
3.0
2.0
6.0
4.0
1.4
2.9 4.0
3.0
25.0
#130: M2.0 X 4.5 (Tapping)
(Silver)
3-732-817-11
3.0
12.0
#131: M4.0 X 12.0
(Silver)
3-452-471-01
3.0
4.0
2.6
6.0
#136: M1.4 X 4.0 (Tapping)
(Black)
3-065-509-11
#135: M2.0 X 2.5
(Black)
7-627-553-28
2.6
7.0
#132: M2.6 X 6.0
(Black)
4-673-655-01
12.0
#134: M2.6 X 7.0
(Black)
3-299-572-01
4.0
12.0
2.0
4.5
#133: M3.0 X 6.0
(Black)
3-452-484-01
6.0
#128: M4.0 X 12.0
(Black)
3-452-472-01
6.0
#129: M3.0 X 12.0
(Black)
7-682-550-09
1.7
2.0
#127: M3.0 X 25.0
(Black)
7-682-654-09
3.5
3.0
4.0
8.0
#126: M2.9 X 3.5
(Black)
3-292-616-01
#125: M1.4 X 3.0
(Black)
3-291-847-01
#124: M1.7 X 2.0
(Silver)
2-599-475-01
1.4
2.0
2.5
4.0
Reverse
985229832.pdf
Revision History
Ver.
Date
1.0
2008.03
Official Release
1.1
2008.05
Revised-1
(A1 DI08-073)
DSC-W110/W115_L2
History
Contents
—
• Addition of Thai model
S.M. revised: Page 3, Page 5-1, Page 5-13
S.M. Rev.
issued
—
Yes

F－1 フランスの木造建築市場 FCBA木造建築産業部建築担当課長

ボードウォークが「チケットボード」の海外展開を開始

モデルテスト用撹拌実験装置システムの新設

強力なミーティングのチェックリスト - OA オーバーイーターズ・アノニマス

プロジェクト・コーディネーションボード

空中ブランコにおける外傷および安全性に対する取り組み

AL Base Board Series

「インベストメントチェーンにおけるWin-Win環境の構築を目指して」[PDF

『Note＋DentNet』サービス提供開始のお知らせ 当社は、歯科医院向け