INSTALLATION INSTRUCTION

INSTALLATION INSTRUCTION
Installation option 1
(without extended arms):
Installation option 2
(with extended arms):
VESA:
400X200 mm
VESA:
100X100 mm
200X100 mm
200X200 mm
Configuration 1
VESA:
300X300 mm
400x400 mm
Configuration 2
MODEL
MD2393-MX
Please read this instruction carefully before installation.
Fits for most 26-55 inches Plasma, LCD and LED TVs.
Weight capacity: 35.5 kg (78 LBS).
Thanks for your purchase! We strive to provide products and services of exceptional quality.
We sincerely invite you to write a review with a good rating. If you wouldn't rate any part of your
experience with five star, please contact us immediately by [email protected],
so that we may resolve the issue for you.
(A0)
US WARNING!
Safety Warning: Thank you for choosing Mounting Dream TV mount. For safe application of model
MD2393-MX, and preventing yourself or others from danger or property loss, please read through this
manual before use. If you do not understand these instructions or have any doubt over safety of
installation, please contact qualified contractor or Mounting Dream customer service. Please check
carefully before assembly to ensure no parts missed or damaged. Our customer service representative
will assist you timely in installation to solve the issue of parts shortage or damage. Replacement parts
purchased through authorized distributor will be delivered to your door. Please do not use defective
parts. Incorrect installation may result in product damage or body injury. Do not apply this product to
any purpose not indicated by Mounting Dream. We shall bear no responsibility for any damage or
injury resulted from incorrect installation, incorrect assembly or misuse.
JP
MD2393-MX
RU
PE Y PE
EH E!
:
MD2393-MX,
,
.
-
,
,
,
.
,
,
,
.
-
DE
,
.
HINWEIS!
Sicherheitshinweis:
dieses Benutzerhandbuch bitte vor dem Gebrauch. Wenn Sie diese Anweisungen nicht verstehen, oder einen
nicht zu einem anderen Zweck, der nicht durch MOUNTING TRAUM angegeben wird. Wir tragen keine
Missbrauch verursacht werden.
FR AVERTISSEMENT!
dommage des biens, veuillez lire soigneusement ce manuel avant l'usage. Si vous ne pouvez pas comprendre
ES
ADVERTENCIA!
Kongzhongshijie, para garantizar el uso en seguro del modelo MD2393-MX, evitar al usuario y otras personas
contratista calificado o Centro de servicio al cliente, Antes de asemblar, verifique cuidadosamente para
asegurarse de que no encuentre la falta de piezas o piezas defectuosos , nuestros representantes deservicio al
, la asamblea incorrecta o uso incorrecto.
AR
!
:
MD2393-MX
"
"
.
.
.
.
"
".
.
CN
:
Attention:
For parts shortage or damage, please contact us directly by [email protected].
New delivery will be timely arranged to replace missed or defective parts.
Installation tools:
2M
Bubble level
Spanner
17-19mm
Stud finder
Hammer
Band tape
2m
Pencil
Screwdriver
(3/8")
(5/32")
Electrodrill
Gifts
HDMI cable
1pc
Velcro cable tie
3pcs
Part list
B-Left extended arm
2pcs
A-Wall plate unit
1pc
1
C-Right extended arm
2pcs
Installation hardware
D--Lag bolt
3pcs
E--Anchor
3pcs
F--4mm Allen key
1pc
G--M6X8 Bolt
8pcs
H--M6X12 Bolt
2pcs
(pre-assembled)
Hardware for TV installation
a--M4X12 bolt
4pcs
b--M5X12 bolt
4pcs
c--M6X12 bolt
4pcs
d--M8X16 bolt
4pcs
e--M4X30 bolt
4pcs
f--M5X30 bolt
4pcs
g--M6X30 bolt
4pcs
h--M8X40 bolt
4pcs
i--M5/M6 spacer
4pcs
j--M8 spacer
4pcs
k--M5/M4 washer
4pcs
l--M6 washer
4pcs
m--M8 spacer
4pcs
2
Installation instruction
Step 1 Remove the bolts (H) with Allen key (F) to separate wall plate
unit (A) into two pieces.
Wall plate
A Wall plate unit
H
F
TV plate
Step 2
Step 3
UP
Step 4
E
D
(3/8")
Concrete wall
CAUTION
Level the wall plate and use
wall plate as a template and
pencil to mark 3 hole locations
on your desired height of the
wall.
Use 3/8" diameter drill bit to drill 3
holes at marked positions to a
depth of 2.36".
Put 3 anchors (E) into drilled
holes, and tap each anchor flush
with the wall by using a hammer.
Then put 3 lag bolts (D) into the
anchors, and tighten each bolt by
using a spanner to mount the wall
plate securely.
To avoid potential personal injury or property damage:
1. Make sure the logo on the wall plate is upward as the picture shows.
2. The wall must be capable of supporting five times the weight of the TV plus the mount.
3. All anchors/lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate.
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
Step 2
16"
Step 3
Step 4
D
(5/32")
Wood stud
3
Use a stud finder to make marks at
the edges of the stud, and mark a
centerline of the stud. Then place
wall plate along the centerline and
use pencil to mark 3 hole locations
on the wall.
Use 5/32" diameter drill bit to
drill 3 holes at marked
positions to a depth of 2.36".
Put 3 lag bolts (D) into the drilled
holes, and tighten each bolt by
using a spanner to mount the wall
plate securely.
Select the TV hardware diameter and length
Your TV type will help you determine which hardware configuration to use.
Hand thread bolts (a, b, c, d, e, f, g, h) into the threaded inserts on the back
of your TV to determine the correct bolt diameter(M4, M5, M6 or M8) and
length.
CAUTION: Avoid potential personal injuries and property damage! Verify
that there are adequate threads to secure the plate to the monitor. If you
encounter resistance, stop immediately and contact customer service. Use
the combination of shortest bolts and spacers to accommodate your needs.
Using hardware that is too long may damage your TV.
Carefully lay your TV on a
non-abrasive surface, or lay it
with a padding underneath it so
as not to damage the screen.
OK
4
Step 5 Attach TV plate to the back of TV
Installation option 1:
If the VESA dimension is 100 mm x 100 mm(3.94 in x 3.94 in),
200 mm x 100 mm(7.87 in x 3.94 in) or 200 mm x 200
mm(7.87 in x 7.87 in), take the following image as reference.
200mm
200mm 100mm
100mm
100mm
200mm
Attach TV plate to the back of TV directly:
1 For the TV with flat back, mount the wall plate with bolt/washer
combination of a+k, b+k, c+l, d.
a
c
5
k
b k
l
d
2
For TV with irregular back, mount the wall plate with bolt/washer/spacer
combination of e+k+i, f+k+i, g+l+i, h+j/m.
(Spacers are highly recommended to be added, thus enlarge the space
between TV and brackets for better functionality.)
spacers(i,j)
Vertical view
Attention: Because of the
TV with irregular back
which makes the VESA
holes recessed, you might
need spacers to fill the
gap.
i
e
k
i
k
f
M4 Diameter Bolt
M5 Diameter Bolt
j/m
g
l
i
M6 Diameter Bolt
h
M8 Diameter Bolt
6
Installation option 2:
If the VESA dimension is 400 mm x 200 mm(15.75 in x 7.85 in),
attach the extended arms (B, C) to the TV plate by screwing in
bolts (G) with Allen key (F). Do not tighten the bolts at this step!
(see Configuration 1).
L
R
C
F
G
200mm
400mm
B
B
C
Configuration 1
If the VESA dimension is 300 mm x 300 mm(11.81 in x 11.81 in) or 400
mm x 400 mm(15.75 in x 15.75 in) , attach the extended arms (B, C) to
the TV plate by screwing in bolts (G) with Allen key (F). Do not tighten
the bolts at this step! (see Configuration 2).
C
F
L
R
B
B
400mm 300mm
C
300mm
400mm
Configuration 2
7
After the assembly of extended arms, attach the assembled plate to
the back of TV, then fasten the bolts(G) tightly after align with the TV's
VESA holes. (Following steps only take Configuration 2 as example):
1
For the TV with flat back, mount the wall plate with bolt/washer
combination of a+k, b+k, c+l, d.
8
2
For TV with irregular back, mount the wall plate with bolt/washer/spacer
combination of e+k+i, f+k+i, g+l+i, h+j/m.
(Spacers are highly recommended to be added, thus enlarge the space
between TV and brackets for better functionality.)
spacers(i,j)
Vertical view
Attention: Because of the
TV with irregular back
which makes the VESA
holes recessed, you might
need spacers to fill the
gap.
M4 Diameter Bolt
M5 Diameter Bolt
g
l
i
h
M6 Diameter Bolt
M8 Diameter Bolt
9
j/m
Step 6 Hang the pre-assembled TV unit on the wall plate.
(Below images only show the TV plate with extended
arms--Configuration 2).
Attention: Cables are
highly recommended to
plug in before hanging
the TV on the wall plate.
Two people are recommended
to hold and position the TV .
Step 7 Make sure the TV unit is horizontal, you can adjust the TV
plate a little bit (+/-5 degrees) to level the TV, then fasten
TV plate by bolts (H) with Allen key (F).
H
Tip: If TV still not level after adjustment, please loosen bolts a bit, hold
TV to adjust to level, then fasten bolts securely with Allen key.
10
Step 8 Adjust the tilting angle with spring loaded handle:
Hold the TV and adjust it to your desired position, and fasten
the handle and the bolt opposite to the handle.
Bolt
Handle
F
To fasten the handle:
Pull
Step A
Turn handle
clockwise
until stopped
by mount.
Step B
Pull out the
handle.
Push
Step C
While holding
handle away
from mount,
turn it
counterclockwise.
Step D
Push and
release
the handle.
Adjust the swivel angle:
Grab TV and slide it to your desired direction.
11
Step E
Turn handle
clockwise to
further fasten
the mount.
Repeat these
steps until
TV firmly
tightened.
Step 9 Manage TV cables orderly and tie them with velcro cable ties.
Product dimensions:
435mm
MAX:400mm
MIN:100mm
490mm
70mm
If you have any questions about the installation, please feel free to contact our after-sales mailbox: [email protected].
For more information, please visit our website: www.mountingdream.com
12

Download Report