CATALOG HEX200 HEXSEALS & E-SEELS В® В® Environmental Sealing Boots for Switches & Potentiometers APM HEXSEAL Why Environmental Protection Is Needed I n many applications ordinary electrical and/or electronic switches and potentiometers are susceptible to damage from water, oil, dust, dirt, salt spray, fungus and other environmental contaminants. Often, even factory-sealed, panel-mounted switches and potentiometers do not protect behind-panel circuitry from the entry of such hostile contaminants through the panel cutout in which the component is mounted. When reliability and survival in such hazardous environments is required, APM HEXSEALвЂ™s broad range of environmental sealing boots provide cost-effective, longterm protection. Protective chamber with secondary inner seal Molded-in mounting nut High tearstrength silicone rubber in actuationcompatible tactility peri*Patented meter sealing rib seals mounting hole and protects behind-panel components HOW APMвЂ™S SEALING BOOTS PROTECT APMвЂ™s sealing boots are designed to protect your switches and potentiometers from hostile environments without compromising, or interfering with, the unitвЂ™s basic operation. Each seal is made from tough, high tear-strength elastomer resistant to most chemicals, lubricants, acids and solvents. Standard colors are black and grey. Boots can be color-matched to panel/function coding. And each remains flexible over a wide operating temperature range вЂ¦ with many units rated at вЂ“94В°F to +400В°F. Most toggle, pushbutton and rotary shaft models feature a molded-in mounting nut, thus serving as both a reliable seal and mechanical mounting. In addition each HEXSEALВ® and E-SEELВ® features an integral proprietary sealing rib which serves to seal the panel cutout in which the component is mounted вЂ¦ thus protecting behind-panel circuitry from leakage or blow-by. Full toggle, pushbutton and rocker switch boots completely envelop the front-of-panel switch mechanism, providing reliable protection even under high-pressure washdowns. Rotary shaft and half toggle/pushbutton seals (in which the actuator protrudes) are designed to snugly hug the actuator to protect against entry of moisture, oil, dirt, dust, and other contaminants. EMI/RFI and Armored Protection. For EMC-sensitive applications, APM offers a number of boots with a built-in, knitted Monel EMI/RFI shield. This integral shield guards against spurious signals entering or leaving equipment 2 Single-piece design for toggle, pushbutton, rocker or rotary styles, in any color Mounting hole Switch housing through the switch mounting hole. Armored toggle and pushbutton switch seals are also available for those instances where severe mechanical abuse is anticipated. Millions in Use. APM HEXSEALвЂ™s environmental sealing boots represent more than 50 years of research and product development. Working closely with both switch users and manufacturers, APM has developed an extensive family of standard and custom boots for toggle, pushbutton, rocker and rotary switches. Today APMвЂ™s environmental seals are used around the world in a wide variety of industrial, commercial, and military applications. We would be pleased to help you select a standard unit, or discuss a custom design to satisfy your unique application needs. Custom Designs. Should your requirement call for boots not shown in this catalog, please contact us for design assistance. The solution often lies in an inexpensive variation of a standard product. All standard EMI/RFI boots feature a knitted Monel shield В© APM HEXSEAL CORP. 1999 Protects against: вЂў Washdowns вЂў Salt water вЂў Oil and grease вЂў Dust and dirt вЂў Corrosion вЂў Fungus вЂў Cleaning solvents вЂў Acids вЂў Ozone вЂў Other harmful environmental contaminants Typical Applications вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў Marine/boating instruments Chain saws Power tools Machine tools Food processing equipment Chemical processing equipment Spas/hot tubs Floor polishers Vacuum cleaners Carpet cleaning systems Lawn tractors Garden power tools Off-road construction equipment Portable test instruments Forklift trucks Golf carts Snowmobiles Jet skis Mobile compressors Airline jetways Snow blowers Farm equipment Commercial laundry equipment Construction elevators Woodworking equipment вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў Navigational equipment Industrial control panels Paint-spraying equipment Automotive/truck exterior control systems Outdoor fuel dispensing systems Tennis ball feeding machines Mopeds/motorcycles Medical equipment Ski lift control panels Industrial/commercial power washers вЂњCrosswalkвЂќ control panels Water pumping equipment Ground support equipment Wireless communications equipment Waste treatment equipment Aircraft instrument panels Pressure washers Hand-held lanterns Or any application requiring environmental protection for panel-mounted switches or potentiometers Features and Benefits вЂў UL and CSA-recognized HEXSEALS and E-SEELS вЂ¦ facilitate easier agency вЂњlistingвЂќ of the equipment in which they are used. вЂў MIL-qualified вЂ¦ most HEXSEALS are QPL approved under MIL-B-5423. вЂў Rugged silicone rubber material вЂ¦ resists tearing and most environmental contaminants. WonвЂ™t discolor, yellow, crack, or dry out. вЂў Perimeter sealing rib вЂ¦ seals the panel cutout in which the switch or potentiometer is mounted. вЂў Secondary inner seal вЂ¦ on many full toggle switch boots protects against entry of contaminants in the event the upper portion of the boot is cut, torn, or punctured. вЂў High-strength rubber-to-metal bond вЂ¦ assures rubber will not peel away from the mounting nut. вЂў Pre-lubricated half-toggle, dual-seal full toggle, and rotary shaft boots вЂ¦ for easier installation on large diameter actuators. вЂў Vibration-resistant mounting вЂ¦ resists switch loosening due to vibration/shock. вЂў Wide operating temperature range вЂ¦ assures long-term performance in the toughest thermal environments. вЂў Black color вЂ¦ E-SEELS feature black anodized hardware and black silicone rubber for aesthetic compatibility. вЂў Wide range of available colors вЂ¦ in addition to standard gray, black, and clear transparent models, units can be molded in an array of colors to meet your needs. вЂў Made in USA вЂ¦ to insure continuity of service throughout the year. 3 3 Performance Levels to Choose From APM HEXSEAL offers three distinct switch seal families from which to choose to meet your applicationвЂ™s price and performance requirements. HEXSEALS E-SEELS SNAP-SEELS MILITARY-QUALIFIED INDUSTRIAL GRADE INDUSTRIALCOMMERCIAL GRADE COMMERCIALCONSUMER GRADE В® В® вЂў QPL-listed versions available. вЂў High tear-strength silicone rubber per ZZ-R-765 вЂў Single-piece design вЂў вЂ“94В°F to +400В°F temperature range вЂў Suitable for military and industrial applications вЂў UL-listed and CSA-certified вЂў UL-listed and CSA certified вЂў High tear-strength silicone rubber вЂў Single-piece construction вЂў вЂ“80В°F to +400В°F temperature range вЂў Suitable for industrial and commercial applications В® вЂў Neoprene rubber вЂў Two-piece design вЂў вЂ“65В°F to +300В°F temperature range вЂў Suitable for commercial and consumer applications Accurate GPS navigation and mapping systems Radio remote crane and hoist controls Portable water quality instruments Boat switch panels ELEC-TRA-MATEВ® electric fishing reels 4 Washdown industrial motor speed and torque controls Product Locator Page Toggle Switch Boots . . . . . . . . . . . . . . . . . 6&7 Pushbutton Boots . . . . . . . . . . . . . . . . . 8&9 Indicator & Illuminated Pushbutton Switch Seals . . . . . . . . . . . . . . . 10 Handset Switch Boots . . . . . . . . . . . . . . . . . 10 Rotary Shaft Seals . . . . . . . . . . . . . . . . . . . 11 . . . . . . . . . . . . . . . . . . 12 Economy Switch Seals . . . . . . . . . . . . . . . . . 13 . . . . . . . . . . . . . . . 14 Custom Switch Boots & Seals . . . . . . . . . . . . 15 . . . Rocker Switch Boots n llatio Insta ctions Instru re nemo op re saluta nitate huma nostre fine mune te: virtute etatis timus a carita te accep cum ruam s inter rex Anneo quibu ium: summ apud ru pluris ut ab sissime dotes: non Partho t. e ingen m ut ru regem glorio nature sublim turus. potes i possu adora nemo ro Parthot. Ego ueroceteras s es: re sum coside e adduc potes ro tum primis illustri ration maifestate re salutanitate op es uel in a nulla mune huma princip coside es uel in fine entia em tua virtute nostre te: summ princip a contin timus exitim te fidem accep cum ruam etatis a carita summ mea esse summ pluris apud ru regem e rex quibus inter fidem ut ab Anneo ium: : sissim Partho t. Ego ingen m ut non dotes glorio regem potes ro tum uero s nature sublime i possu adoraturus. Ego re nemo sum op coside primis cetera s es: e adduc tum re saluta nitate es uel in entia ration maifestate illustri mune huma primis entia nulla em tua a contin esse fine virtute nostre princip summ mea timus continesse exitim etatis caritate: te fidem a caritate: accep cum ruam te a mea Anneo s inter e rex apud apud summ : quibu m: summ ut ab gloriosissim dotes ingenium:ut non pluris geniu non pluris Parthorut. uero s nature e turus. m ut m turus. potes ro cetera s es: sublim i possusum adora i possu adorare nemo sum in op coside illustri ratione adduc state ratione adducstate re saluta maife nitate es uel maife mune nulla nulla em tua huma princip summa fine entia em tua virtute nostre te: exitim a contin timus exitim te fidem accep cum ruam etatis a carita ro summ mea esse summ pluris apud coside e rex quibus inter fidem ut ab Anneo ium: e op : non sissim ut ingen turus. dotes m glorio regem adora uero s nature sublime i possu Ego sum cetera s es: e adduc state tum ration illustri maife primis entia nulla em tua contin esse exitim mea APM HEXS EAL Installation Instructions Qualified Products List The following standard APM HEXSEALS are QPL-Listed, per QPL5423. Other QPL-listed products are available. Please consult factory. HEXSEALS Military P/N M5423/01-01 . M5423/01-02 . M5423/02-01 . M5423/03-01 . M5423/04-01 . M5423/05-01 . M5423/05-02 . M5423/06-01 . M5423/06-02 . M5423/06-03 . M5423/06-04 . M5423/07-01 . M5423/07-02 . M5423/07-03 . M5423/07-04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . APM P/N N-1030 . . IN1030RFI N-1030B . 2030-B . . N-5030 . . N-5030L. . N-5030R . 3070 . . . 3075 . . . 3073 . . . 3077 . . . N-3030 . . NC-3030 . NH-3030 . N-3040 . . HEXSEALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page . 6 . 7 . 6 . 7 . 6 . 6 . 6 . 9 . 9 . 9 . 9 . 8 . 8 . 8 . 8 Military P/N M5423/07-05 . M5423/07-06 . M5423/07-07 . M5423/07-08 . M5423/07-09 . M5423/07-10 . M5423/07-11 . M5423/07-12 . M5423/09-01 . M5423/09-02 . M5423/09-03 . M5423/09-04 . M5423/09-05 . M5423/09-06 . M5423/09-07 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . APM P/N Page NH-3030S. . . . . . . 8 N-3030RFI . . . . . . 9 NC-3030RFI . . . . . 9 NH-3030RFI . . . . . 9 N-3040RFI . . . . . . 9 NH-3030SRFI. . . . . 9 N-3030-2513 . . . . . 8 NC-3030-2513 . . . . 8 N-9030-1/8 . . . . . 11 N-9030-1/4 . . . . . 11 N-9040-1/8 . . . . . 11 N-9060-1/4 . . . . . 11 N-9065-3/8 . . . . . 11 N-9063-1/4 . . . . . 11 N-9030-1/8RFI. . . . 11 HEXSEALS Military P/N M5423/09-08 . M5423/09-09 . M5423/09-10 . M5423/09-12 . M5423/09-14 . M5423/10-01 . M5423/10-02 . M5423/10-03 . M5423/11-01 . M5423/12-A9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . APM P/N Page N-9030-1/4RFI. . . 11 N-9040-1/8RFI. . . 11 N-9060-1/4RFI. . . 11 N-9063-1/4RFI. . . 11 N-9033-1/4RFI. . . 11 N-5040G . . . . . . 8 N-5040R . . . . . . 8 N-5040 . . . . . . . 8 N-5032B . . . . . . 6 1112/7 HANDSET BOOTS Military P/N APM P/N Page M5423/15-01 . . . . . . 1211/13 . . . . . . 10 M5423/15-02 . . . . . . 1211/14 . . . . . . 10 M5423/15-03 . . . . . . 1211/31 . . . . . . 10 5 Toggle Switch Boots HEXSEALВ® and E-SEELВ® toggle switch boots are molded from a high tear-strength silicone rubber bonded to a built-in mounting nut. Each encloses the base of the protruding switch bushing and forms a watertight and dust-tight seal against the front panel surface. SPECIFICATIONS Material: HEXSEALS: Silicone rubber conforms to ZZ-R-765 Class III, GR 50 (unless otherwise specified) E-SEELS вЂ” Silicone rubber polymer type ASTM D 1418 Mounting Nut: HEXSEALS: Brass, nickel-plated E-SEELS: Brass, black-oxide Temperature Range: HEXSEALS: вЂ“94В°F to +400В°F E-SEELS: вЂ“80В°F to +400В°F Pressure Range: Exceeds 15 psi internal and 1500 psi external. (N5032B: 10 psi) Operational Life: 50,000 actuations (minimum). Shelf Life: Excess of 25 years. Resistant to: Salt spray, sunlight, ozone, weather, fungus, and most acids and lubricating oils Military Approvals: Most HEXSEALS are QPL-approved to MIL-B-5423. (See QPL listing on page 5.) Agency Recognition: E-SEELS and HEXSEALS are UL-listed to UL Std. 50 types 1-13, and meet CSA standards. Installation: Please see installation instructions on page 14. HOW TO ORDER Specify APM boot part number and, if necessary, the appropriate bushing adaptor part number (please see page 14). Full-Toggle Switch Boots (with constant I.D.) Thread Size FIGURE 3 N-5030 N-5030LвЂ N-5030R N-5030S N-1030 N-1030 1/2-32 C1131/27 M6 (metric) 15 /32-32NS-2B M12 (metric) 15 /32-32NS-2B 15 /32-32NS-2B 15 /32-32NS-2B 15 /32-32NS-2B 1 /2-32NS-2B 1 /2-32NS-2B 5 /8-32UNS-2B 15 /32-32NS-2B Max. Toggle Height Above Bushing (in.) .37 .437 .812 .66 .66 .90 1.08 .66 .66 .78 .71 A Throat or I.D. in. .116 .210 .234 .219 .256 .219 .390 .219 .256 .187 .219 B Height mm 2.95 5.35 5.95 5.55 6.50 5.55 9.92 5.55 6.50 4.76 5.55 in. .562 .625 .859 .844 .844 1.093 1.328 .844 .844 .844 .937 mm 14.30 15.88 21.83 21.44 21.44 27.77 33.37 21.44 21.44 21.44 23.80 C Flat in. .352 .625 .625 .625 .625 .625 .625 .625 .625 .750 .625 mm 9.00 15.88 15.88 15.88 15.88 15.88 15.88 15.88 15.88 19.05 15.88 Color* Gray Gray Gray Gray Gray Gray Black вЂў вЂў вЂў вЂў вЂў вЂў вЂў Figure 2 Military Part Number APM Boot Part Number вЂ” вЂ” вЂ” M5423/01-02 вЂ” вЂ” вЂ” вЂ” вЂ” вЂ” вЂ” 1131/25 1131/33 1131/40 IN-1030 1131/31 1131/26 N-1002 IN-1030 1/2-32 1131/32 1131/23 C1131/28 Color* Black Gray Black Gray Gray Gray Gray Gray Black Gray Black E-SEEL FIGURE 2 APM Boot Part Number E-SEEL Max. Toggle A Height Throat B C Military Above or I.D. Height Flat Part Bushing Number (in.) in. mm in. mm in. mm 1 /4-40NS-2B .31 .104 2.64 .422 10.72 .375 9.58 M5423/04-01 1 /4-40NS-2B .37 .062 1.53 .500 12.70 .375 9.52 M5423/05-01 1 /4-40NS-2B .28 .062 1.58 .390 9.91 .375 9.52 M5423/05-02 1 /4-40NS-2B .50 .062 1.58 .594 15.08 .375 9.52 вЂ” 15 /32-32NS-2B .66 .219 5.55 .844 21.44 .625 15.88 M5423/01-01 1 /2-32NS-2B .66 .219 5.55 .844 21.44 .625 15.88 вЂ” 15 /32-32NS-2B .71 .219 5.55 .937 23.81 .625 15.88 вЂ” *Other colors available. Please consult factory. вЂ Material conforms to ZZ-R-765 Class III, Gr. 25 Thread Size Figure 1 HEXSEAL Full-Toggle Switch Boots (with integral secondary seal) HEXSEAL FIGURE 1 вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў *Other colors available. Please consult factory. 1 /4-40NS-2B /32-32NS-2B 1 /2-32NS-2B 15 /32-32NS-2B 15 A Throat or I.D. in. .047 .078 .078 .078 mm 1.19 1.98 1.98 1.98 *Other colors available. Please consult factory. 6 B Height in. .250 .437 .437 .437 mm 6.35 11.10 11.10 11.10 C Flat in. .375 .625 .625 .625 Military Part Number mm 9.53 15.88 15.88 15.88 M5423/11-01 M5423/02-01 вЂ” вЂ” вЂ вЂ Material conforms to ZZ-R-765, Class II, GR. 40. Figure 3 APM Boot Part Number N-5032BвЂ вЂ N-1030B N-1030B1/2-32 C1132/20 Color* Gray Gray Gray Black E-SEEL Thread Size Toggle Diameter Accommodated (in.) .062-.188 .155-.240 .155-.240 .155-.240 HEXSEAL Half-Toggle Switch Boots (toggle actuator protrudes) вЂў вЂў вЂў вЂў Max. Toggle Thread Height Size Above Bushing (in.) 15 /32-32NS-2B .66 A Throat or I.D. in. .219 Figure 4 B Height mm 5.55 in. .875 C Flat mm 21.44 in. .625 Military Part Number APM Boot Part Number вЂ” N-1030A mm 15.88 Color Gray вЂў E-SEEL Armored Full Toggle Boots HEXSEAL FIGURE 4 Nickel plated brass cap bonded to boot. Thread Size 1 /4-40NS-2B /32-32NS-2B 1 /2-32NS-2B 1 /4-40NS-2B 1 /4-40NS-2B 15 Max. Toggle Height Above Bushing (in.) .36 .66 .66 .28 .50 A Throat or I.D. in. .062 .219 .219 .062 .062 Figure 5 B Height mm 1.58 5.55 5.55 1.58 1.58 in. .500 .844 .844 .390 .594 C Flat mm 12.70 21.44 21.44 9.90 15.08 in. .375 .625 .625 .375 .375 mm 9.52 15.88 15.88 9.52 9.52 Military Part Number APM Boot Part Number вЂ” M5423/01-02 вЂ” вЂ” вЂ” N-5030L RFI IN-1030 RFI IN-1030 RFI 1/2-32 N-5030R RFI N-5030S RFI Color* Gray Gray Gray Gray Gray вЂў вЂў вЂў вЂў вЂў E-SEEL EMI/RFI Shielded Full Toggle Boots HEXSEAL FIGURE 5 *Other colors available. Please consult factory. All standard EMI/RFI boots feature a knitted Monel shield. RFI/EMI shielded boots have an operational life of 15,000 actuations (minimum) Back-of-Panel Mounted Toggle Switch Boots FIGURE 7 Width inch .750 mm 19.05 C Clearance Boot Hole Diameter inch mm .510 12.95 Military Part Number APM Boot Part Number Color* вЂ” 2030 Gray вЂў Half Toggle Boot (Toggle Actuator Protrudes) A Throat or I.D. D Distance Between Mtg. Holes inch mm inch mm inch mm .093 2.38 .500 12.70 1.813 46.04 *Other colors available. Please consult factory. B Height Width inch .750 mm 19.05 C Clearance Boot Hole Diameter inch mm .510 12.95 E-SEEL D Distance Between Mtg. Holes inch mm inch mm inch mm .315 7.91 .938 23.82 1.813 46.04 *Other colors available. Please consult factory. B Height Figure 7 Military Part Number APM Boot Part Number Color* M5423/03-01 2030B Gray вЂў DIMENSIONS FOR REFERENCE ONLY. 7 E-SEEL A Throat or I.D. Figure 6 HEXSEAL Full Toggle Boot HEXSEAL FIGURE 6 Pushbutton Boots HEXSEALВ® and E-SEELВ® push button boots are molded from a high tear-strength silicone rubber bonded to a built-in mounting nut. Each encloses the base of the protruding switch bushing and forms a watertight and dust-tight seal against the front panel surface. SPECIFICATIONS Material: HEXSEALS: Silicone rubber conforms to ZZ-R-765 Class III, Gr. 60 unless otherwise specified. E-SEELS: Silicone rubber polymer type ASTM D1418. Mounting Nut: HEXSEALS: Brass, nickel-plated (unless otherwise noted) E-SEELS: Brass, black-oxide Temperature Range: HEXSEALS: вЂ“94В°F to +400В°F E-SEELS: вЂ“80В°F to +400В°F Pressure Range: Exceeds 15 psi internal and 1500 psi external. Operational Life: 50,000 actuations (minimum) Shelf Life: In excess of 25 years Resistant to: Salt spray, sunlight, ozone, weather, fungus, and most acids and lubricating oils Military Approvals: Most HEXSEALS are QPL-approved to MIL-B-5423. (See QPL listing on page 5.) Agency Recognition: E-SEELS and HEXSEALS are UL-listed to UL Std. 50 types 1-13, and meet CSA standards. Installation: Please see installation instructions on page 14. HOW TO ORDER Specify APM boot part number and, if necessary, the appropriate bushing adaptor part number (please see page 14). FIGURE 8 Full Pushbutton Boots FIGURE 9 C A 8-40 NS-2B 8-40 NS-2B 1 /4-32NS-2B 1 /4-32NS-2B 1 /4-40NS-2B 1 /4-40NS-2B 1 /4-40NS-2B 5 /16-32UNEF-2B 3 /8-27NS-2B 3 /8-32NEF-2B 7 /16-28UNEF-2B 7 /16-32UN-2B 15 /32-32NS-2B 15 /32-32NS-2B 15 /32-32NS-2B 15 /32-32NS-2B 1 /2-32NS-2B 1 /2-32NS-2B 1 /2-32NS-2B 5 /8-24NEF-2B 15 /32-32NS-2B 15 /32-32NS-2B inch .226 .297 .313 .531 .313 .313 .531 .359 .653 .653 .719 .719 .547 .547 .719 .719 .547 .547 .734 .609 .547 .719 mm 5.70 7.54 7.94 13.49 7.94 7.94 13.49 9.13 16.60 16.60 18.26 18.26 13.89 13.89 18.26 18.26 13.89 13.89 18.65 15.48 13.89 18.26 B Flat inch mm .250 6.35 .250 6.35 .375 9.53 .375 9.53 .375 9.53 .375 9.53 .375 9.53 .437 11.11 .500 12.70 .500 12.70 .625 15.88 .625 15.88 .625 15.88 .625 15.88 .625 15.88 .625 15.88 .625 15.88 .625 15.88 .625 15.88 .750 19.05 .625 15.88 .625 15.88 C I.D. inch mm .125 3.18 .120 3.18 .188 4.76 .125 3.18 .188 4.76 .188 4.76 .125 3.18 .156 3.97 .300 7.60 .300 7.60 .422 10.72 .422 10.72 .422 10.72 .422 10.72 .422 10.72 .422 10.72 .422 10.72 .422 10.72 .422 10.72 .515 13.10 .422 10.72 .422 10.72 Military Part Number вЂ” SCL6303A-03 M5423/10-01 вЂ” M5423/10-03 M5423/10-02 вЂ” вЂ” вЂ” вЂ” вЂ” вЂ” M5423/07-01 M5423/07-11 M5423/07-02 M5423/07-12 M5423/07-03 M5423/07-05 вЂ” M5423/07-04 вЂ” вЂ” B O.D. inch mm .641 16.27 .766 19.45 .641 16.27 .641 16.27 .641 16.27 .641 16.27 C I.D. inch mm .320 8.11 .375 9.53 .320 8.11 .320 8.11 .320 8.11 .320 8.11 Military Part Number вЂ” вЂ” вЂ” вЂ” вЂ” вЂ” B Flat inch mm .625 15.88 .625 15.88 .625 15.88 C I.D. inch mm .344 8.73 .344 8.73 .344 8.73 Military Part Number вЂ” вЂ” вЂ” APM Boot Part Number Color* 1231/17 N5045 N5040G 1231/32 N5040 N5040R 1231/31 1231/27 1231/8 1231/35 NC3030 7/16-28 NC3030 7/16-32 N3030 N3030-2513 NC3030 NC3030-2513 NH3030 NH3030S NC3030H N3040 C1231/41 C1231/42 Gray Gray Gray Gray Gray Gray Gray Gray Gray Clear Clear Gray Gray Clear Gray Clear Gray Gray Gray Gray Black Black E-SEEL Figure 8 A HEXSEAL Thread Size Max. Plunger Height inch mm .118 3.00 .188 4.76 .203 5.16 .453 11.51 .141 3.57 .203 5.16 .344 11.51 .212 5.41 .545 13.80 .545 13.80 .438 11.11 .438 11.11 .281 7.14 .281 7.14 .438 11.11 .438 11.11 .281 7.14 .188 4.76 .469 11.91 .281 7.14 .281 7.14 .438 11.11 вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў Thread Size 3 /8-27NS-2B /32-32NS-2B /8-24NF-2B 3 /8-27NS-2B 3 /8-27NS-2B 3 /8-32NEF-2B 15 FIGURE 10 3 A inch .609 .719 .609 .609 .609 .609 mm 15.48 18.26 15.48 15.48 15.48 15.48 APM Boot Part Number Color* 1221/12 1221/15 C1221/22 C1221/21 C1221/21 4 C1221/23 Gray Gray Clear Black Clear Clear E-SEEL Aluminum insert Max. Plunger Height inch mm .330 8.38 .400 10.14 .330 8.38 .330 8.38 .330 8.38 .330 8.38 HEXSEAL Figure 9 B вЂў вЂў вЂў вЂў вЂў вЂў Mounting nut material: Aluminum 7 /16-28UNEF-2B /16-32UN-2B /32-32NS-2B 7 15 inch mm .797 20.24 .797 20.24 .797 20.24 *Other colors available. Please consult factory. 8 APM Boot Part Number 7 NC3030FL /16-28 NC3030FL 7/16-32 NC3030FL Color* Gray Gray Gray вЂў вЂў вЂў E-SEEL Thread Size A HEXSEAL Figure 10 Max. Plunger Height inch mm .313 7.94 .313 7.94 .313 7.94 5 /8-27NS-2A /8-24NEF-2A /8-27NS-2A 5 /8-24NEF-2A 5 5 A inch .906 .906 .906 .906 Figure 11 B C O.D. Inside Thread inch mm 1 .875 22.23 /2-32NS-2B 1 /2-32NS-2B .875 22.23 1 /2-32NS-2B .875 22.23 1 .875 22.23 /2-32NS-2B mm 23.03 23.02 23.02 23.02 Military Part Number M5423/06-01вЂ M5423/06-03 M5423/06-02вЂ M5423/06-04 APM Boot Part Number 3070 3073 3075 3077 Color* Gray Gray Gray Gray вЂў вЂў вЂў вЂў E-SEEL Outside Thread PlungerBushing Height inch mm .438 11.11 .438 11.11 .688 17.46 .688 17.46 HEXSEAL FIGURE 11 Panel-Mounted Full Pushbutton Boots *Other colors available. Please consult factory. вЂ Inactive for new designs. Material conforms to ZZ-R-765 Class III, Gr. 50. 7 /16-28NS-2B /16-32UN-2B 15 /32-32NS-2B 1 /2-32NS-2B 7 A Height inch mm .547 13.89 .547 13.89 .547 13.89 .547 13.89 B Flat inch .625 .625 .625 .625 C Throat inch mm .250 6.35 .250 6.35 .250 6.35 .250 6.35 mm 15.88 15.88 15.88 15.88 Military Part Number вЂ” вЂ” вЂ” вЂ” APM Boot Part Number N3030B 7/16-28 N3030B 7/16-32 N3030B NH3030B Color* Clear Clear Clear Clear E-SEEL Thread Size Figure 12 HEXSEAL FIGURE 12 Half-Pushbutton Boots (Pushbutton Actuator Protrudes) вЂў вЂў вЂў вЂў *Other colors available. Please consult factory 15 15 /32-32NS-2B /32-32NS-2B A inch .984 .984 mm 25.00 25.00 Figure 13 B Flat inch mm .750 19.05 .750 19.05 C I.D. inch mm .422 10.72 .422 10.72 Military Part Number вЂ” вЂ” APM Boot Part Number Color 1238/1 SS 1238/5* SS вЂ вЂ вЂ вЂ вЂў вЂў E-SEEL Thread Size Plunger Height inch mm .438 11.11 .438 11.11 HEXSEAL FIGURE 13 Armored Pushbutton Boots *P/N 1238/5 features a 11/4" diameter actuator button. вЂ вЂ Stainless steel housing with silicone boot. FIGURE 14 EMI/RFI Shielded Full Pushbutton Boots 15 /32-32NS-2B /32-32NS-2B /2-32NS-2B 1 /2-32NS-2B 5 /8-24NEF-2B 1 /2-32NS-2B 15 1 mm 7.14 11.11 7.14 4.76 7.14 11.91 inch .547 .719 .547 .547 .609 .734 mm 13.89 18.26 13.89 13.89 15.48 18.65 B Flat inch .625 .625 .625 .625 .750 .625 mm 15.88 15.88 15.88 15.88 19.05 15.88 Figure 14 C I.D. inch .422 .422 .422 .422 .516 .422 mm 10.72 10.72 10.72 10.72 13.10 10.72 Military Part Number M5423/07-06 M5423/07-07 M5423/07-08 M5423/07-10 M5423/07-09 вЂ” APM Boot Part Number Color* N3030RFI NC3030RFI NH3030RFI NH3030SRFI N3040RFI NC3030HRFI Gray Gray Gray Gray Gray Gray E-SEEL inch .281 .438 .281 .188 .281 .469 A HEXSEAL Thread Size Plunger Height вЂў вЂў вЂў вЂў вЂў вЂў *Other colors available. Please consult factory. All standard EMI/RFI boots feature a molded knitted Monel shield. EMI/RFI shielded pushbutton boots have an operational life of 15,000 actuations (minimum) Back-of-Panel Mounted Pushbutton Boots inch mm inch mm .531 13.49 .453 11.51 .438 11.11 .359 9.13 this group conform to ZZ-R-765 D Hole Width Locations inch mm inch mm 1.813 46.04 .750 19.05 1.813 46.04 .750 19.05 Class III, Gr. 50. Military Part Number APM Boot Part Number Color вЂ” вЂ” 3050 3051 Clear Clear вЂў вЂў FIGURE 16 Half Pushbutton Boots (Pushbutton Actuator Protrudes) D A B C Hole Width Height O.D. Throat Locations inch mm inch mm inch mm inch mm inch mm .578 14.68 .531 13.49 .156 3.97 1.813 46.04 .750 19.05 Part numbers in this group conform to ZZ-R-765 Class III, Gr. 50. Figure 16 Military Part Number APM Boot Part Number Color вЂ” 3050B Clear DIMENSIONS FOR REFERENCE ONLY. 9 E-SEEL C вЂў E-SEEL inch mm .906 23.02 .399 10.13 Part numbers in B O.D. HEXSEAL A Height Figure 15 HEXSEAL FIGURE 15 Full Pushbutton Boots Indicator & Illuminated Pushbutton Switch Seals HEXSEALВ® indicator and lighted pushbutton switch boots are molded from RUBRGLASв„ў, APMвЂ™s proprietary transparent silicone rubber formulation, bonded to a threaded metal insert. Each encloses the base of the protruding indicator or lighted pushbutton switch bushing and forms a watertight and dust-tight seal against the front panel surface. FIGURE 17 RUBRGLASВ® Seals Figure 17 B Height C Boot O.D. Thread Fits Indicator Military APM Boot Part Color Size Light # Part Number inch mm inch mm inch mm Number 11/16-32NS-2B 1.000 25.40 .750 19.04 .712 18.08 MS-25041 вЂ” 4082 Clear 11/16-32NS-2B 1.000 25.40 1.000 25.40 .712 18.08 вЂ” вЂ” 4086 Clear 13/16-32NS-2B 1.125 28.58 .812 20.64 .843 21.43 вЂ” вЂ” 4080 Clear 7/8-32NS-2B 1.125 28.58 .812 20.64 .858 21.79 вЂ” вЂ” 4085 Clear .850-24NS-2B 1.125 28.58 .812 20.64 .838 21.28 вЂ” вЂ” 4088 Clear RUBRGLASв„ў seals have an operational life of 30,000 actuations (minimum), and a pressure rating of 15 psi internal/external. Note: See page 15 for example of custom designed seals for lighted pushbutton switches. DIMENSIONS FOR REFERENCE ONLY. C B HEXSEAL A Width вЂў вЂў вЂў вЂў вЂў A Matching Colorizing Incandescent Lamp Filters Available APM HEXSEAL also offers a broad range of silicone colorizing filters for miniature incandescent lamps. These easy-to-install filters turn a white/clear lamp into a colored indicator. Ask for SiliKromeВ® catalog SK100. Handset Switch Boots Ideal for wireless communications applications, HEXSEALВ® handset switch boots are engineered to rugged specifications, withstanding a minimum of half a million actuations. SPECIFICATIONS FIGURES 18, 19 & 20 DESCRIPTION A Microphone M52, Handset H33/PT Handset H189 Handset H250 *Other colors available. Please consult factory. inch .652 .406 .576 B mm 16.5 10.4 14.6 inch 2.248 1.300 .808 D Hole Locations C mm 57.1 33.0 20.5 inch 2.148 1.250 .718 mm 54.5 31.7 18.2 inch 2.594 3.380 1.500 FIGURE 18 Microphone M52, Handset H33/PT Part No. 1211/13 Handset H189 Part No. 1211/14 inch .612 .700 .687 mm 15.5 11.3 17.5 APM Part Number Color* M5423/15-01 M5423/15-02 M5423/15-03 1211/13 1211/14 1211/31 Gray Black Black вЂў вЂў вЂў FIGURE 20 Handset H250 Part No. 1211/31 B C B C A 10 mm 66.0 85.9 38.0 Military Part Number FIGURE 19 B C D 2.828 Width HEXSEAL Material: Boot: Silicone rubber. Conforms to ZZ-R-765 Class III, Gr. 50 Temperature Range: вЂ“94В°F to +400В°F Shelf Life: Excess of 25 years. Operational Life: 500,000 actuations, minimum. Resistant to: Salt spray, weather, sunlight, ozone and most acids Military Specifications: Most Hexseal products are QPL approved under Mil-B-5423. For QPL listing, see page 5. A A D 3.661 DIMENSIONS FOR REFERENCE ONLY. D 1.953 Rotary Shaft Seals For Switches & Potentiometers HEXSEALВ® and E-SEELВ® rotary shaft seals are molded from a high tear-strength silicone rubber bonded to a built-in mounting nut. Each seal surrounds the rotary shaft and forms a watertight and dust-tight seal against the shaft and front panel surface. SPECIFICATIONS Material: HEXSEALS: Silicone rubber conforms to ZZ-R-765 Class III, GR 60 (unless otherwise specified) E-SEELS: Silicone rubber polymer type ASTM D 1418 Mounting Nut: HEXSEALS: Brass, nickel-plated E-SEELS: Brass, black oxide Temperature Range: HEXSEALS: вЂ“94В°F to +400В°F E-SEELS: вЂ“80В°F to +400В°F Pressure Range: Exceeds 15 psi internal and 1500 psi external Operational Life: 50,000 actuations, minimum Shelf Life: In excess of 25 years Resistant to: Salt spray, sunlight, ozone, weather, fungus and most acids and lubricating oils Military Approvals: Most HEXSEALS are QPL-approved under MIL-B-5423 (see QPL listing on page 5) Agency Recognition: E-SEELS and HEXSEALS are UL-listed to UL Std. 50 types 1-13, and meet CSA standards Installation: Please see installation instructions on page 14. HOW TO ORDER Specify APM boot part number and, if necessary, the appropriate bushing adaptor part number (please see page 14). 1 /4-28NF2B /4-32NEF-2B 3 /8-32NEF-2B 3 /8-32NEF-2B 3 /8-32NEF-2B 3 /8-32NEF-2B 15 /32-32NS-2B 1 /2-32NS-2B 5 /8-24NEF-2B 5 /8-24NEF-2B 3 /8-32NEF-2B 1 A Shaft Size inch mm .125 3.18 .125 3.18 .125 3.18 .188 4.78 .250 6.35 .250 6.35 .250 6.35 .250 6.35 .375 9.53 .500 12.70 .250 6.35 B Height inch mm .219 5.56 .219 5.56 .219 5.56 .219 5.56 .219 5.56 .359 9.12 .219 5.56 .219 5.56 .219 5.56 .219 5.56 .219 5.56 C Flat inch .375 .375 .500 .500 .500 .500 .625 .625 .750 .750 .500 Military Part Number вЂ” M5423/09-03 M5423/09-01 вЂ” M5423/09-02 вЂ” M5423/09-04 M5423/09-06 M5423/09-05 вЂ” вЂ” mm 9.53 9.53 12.70 12.70 12.70 12.70 15.88 15.88 19.05 19.05 12.70 APM Boot Part Number Color* N9042 x 1/8 N9040 x 1/8 N9030 x 1/8 N9030 x 3/16 N9030 x 1/4 N9033 x 1/4 N9060 x 1/4 N9063 x 1/4 N9065 x 3/8 N9065 x 1/2 C1332/40 Gray Gray Gray Gray Gray Gray Gray Gray Gray Gray Black E-SEEL Thread Size Figure 21 HEXSEAL FIGURE 21 Rotary Shaft Seals вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў *Other colors available. Please consult factory. Military Part Number M5423/09-09 M5423/09-07 M5423/09-08 M5423/09-14 M5423/09-10 M5423/09-11вЂ M5423/09-12 вЂ” вЂ” вЂ” APM Boot Part Number 1 N9040 x /8 RFI N9030 x 1/8 RFI N9030 x 1/4 RFI N9033 x 1/4 RFI N9060 x 1/4 RFI N9065 x 3/8 RFI N9063 x 1/4 RFI N9042 x 1/8 RFI NLK9030 x 1/8 RFI NLK9030 x 1/4 RFI вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў вЂў Figure 23 C Flat inch mm .500 12.70 .625 15.88 .625 15.88 Lock Nut O.D. inch mm .344 8.74 .469 11.91 .469 11.91 Military Part Number APM Boot Part Number вЂ” вЂ” вЂ” NLK9040 x 1/8 NLK9030 x 1/8 NLK9030 x 1/4 DIMENSIONS FOR REFERENCE ONLY. 11 Color* Gray Gray Gray вЂў вЂў вЂў E-SEEL A B Shaft Size Height Thread Size inch mm inch mm 1 /4-32NS-2B .125 3.18 .500 12.70 3 /8-32NS-2B .125 3.18 .531 13.49 3 /8-32NS-2B .250 6.35 .531 13.49 *Other colors available. Please consult factory. Gray Gray Gray Gray Gray Gray Gray Gray Gray Gray HEXSEAL FIGURE 23 Locking Rotary Shaft Seals Color* E-SEEL Figure 22 A B C Shaft Size Height Flat Thread Size inch mm inch mm inch mm 1 /4-32NF2B .125 3.18 .219 5.56 .375 9.53 3 /8-32NEF-2B .125 3.18 .219 5.56 .500 12.70 3 /8-32NEF-2B .250 6.35 .219 5.56 .500 12.70 3 /8-32NEF-2B .250 6.35 .359 9.12 .500 12.70 15 /32-32NS-2B .250 6.35 .219 5.56 .625 15.88 5 /8-24NEF-2B .375 9.53 .219 5.56 .750 19.05 1 /2-32NS-2B .250 6.35 .219 5.56 .625 15.88 1 /4-28NF-2B .125 3.18 .219 5.56 .375 9.53 3 /8-32NEF-2B .125 3.18 .531 13.49 .625 15.88 3 /8-32NEF-2B .250 6.35 .531 13.49 .625 15.88 *Other colors available. Please consult factory. вЂ Inactive for new designs. All Standard RFI/EMI boots feature knitted Monel wire shields. HEXSEAL FIGURE 22 RFI/EMI Shielded Rotary Shaft Seals Rocker Switch Boots E-SEELВ® (Rock-R-Seelв„ў) rocker switch boots are molded from RUBRGLASв„ў вЂ” APMвЂ™s proprietary high tear-strength, transparent silicone rubber. These durable and flexible boots seal out dust, dirt, and moisture вЂ¦ without compromising switch operability, position status viewing or legend visibility. Each is designed to fully enclose the switch bezel, while our unique molded-in вЂњpanel sealing ribвЂќ forms a watertight and dust-tight seal against the front panel surface. 5 SPECIFICATIONS 6 Material: APM RUBRGLASв„ў (transparent silicone rubber), polymer type, ASTM D1418 Temperature Range: вЂ“80В°F to +400В°F Operational Life: 50,000 actuations (minimum) Resistant to: Salt spray, sunlight, ozone, weather, fungus, and most acids and lubricating oils Agency Recognition: Rock-R-Seelsв„ў are UL-listed to UL Std. 50, types 1, 2, 4R, 5, 12, 12K, 13, and meet CSA standards Shelf Life: Excess of 25 years 7 1 2 3 HOW TO ORDER 4 Specify APM boot part number. PHOTOS 1-7 Dimensions Photo # E-SEEL Part # A B C D E in. mm in. mm in. mm in. mm in. mm Compatible with These Rocker Switch Manufacturers (Partial List) 1 C1111/7 .359 9.13 .609 15.48 .937 23.81 1.703 43.26 .900 22.87 Consult Factory 2 C1113/62 .297 7.54 .797 20.24 .687 17.46 1.093 27.78 .968 24.61 Arrow Hart вЂ“ 2600 Series 3 C1113/63 .297 7.54 .406 10.32 .687 17.46 1.093 27.78 .515 13.10 Arrow Hart вЂ“ 2600 Series 4 C1113/66 .228 5.79 .348 8.84 .531 13.46 .750 19.05 .531 13.49 Carlingswitch #621 5 C1113/70 .297 7.54 .437 11.11 .875 22.23 1.218 30.96 .640 16.27 Carlingswitch RSC Series 6 C1113/71 .413 10.49 .687 17.46 1.046 26.59 1.327 36.51 .703 17.86 Carlingswitch M Series Airpax R11 Eaton/Heinemann LC-1 Potter W-33 Carling LTI6 C1113/80 .560 14.22 .750 19.05 1.375 34.92 1.750 44.45 .900 22.86 7 C1113/75 .413 10.49 .687 17.46 1.046 26.59 1.437 36.51 1.390 35.32 Carlingswitch M Series Airpax R21 Eaton/Heinemann LC-2 Not Shown C1213/53 C1213/60 .312 .350 9.14 10.16 .700 1.000 19.81 21.08 .700 .820 19.81 21.08 1.120 1.120 29.21 29.21 .800 .800 23.11 23.11 Oslo Oslo DIMENSIONS FOR REFERENCE ONLY. S Series S Series Carlingswitch M Series Rocker Actuator Switch with C1113/71 E-SEEL 12 Economy Switch Seals SNAPSEELS В® SPECIFICATIONS SNAPSEELSВ® combine economy with performance for more moderate temperature conditions and lower-demand commercial-grade applications. Each consists of a molded neoprene boot which snaps over a specially designed shouldered mounting nut. These inexpensive boots are an ideal way to protect switches and potentiometers against dust, dirt, grease and moderate amounts of moisture. Material: Boot: Neoprene. Color: Black (other materials and colors available on special order.) Temperature Range: вЂ“65В°F to +300В°F Shelf Life: 2 years. Mounting Nut: Aluminum (see table below) Installation: A. Mount the switch using SNAPSEEL shouldered mounting nut. B. Press SNAPSEEL over switch actuator and snap over nut. HOW TO ORDER Select boot to fit switch type and dimensions. Choose shouldered mounting nut to mate with selected boot. SEE TABLE BELOW FOR SHOULDERED MOUNTING NUT OPTION. For example: When ordering a pushbutton boot PN 1211/10, also order its companion shouldered mounting nut P/N 2120/122/1. Pushbutton Boots Part No. 1211/10 Pushbutton Height from panel: Up to 9/16" Pushbutton Diameter: Up to 1/4" Bushing Diameter: 15/32" maximum Part No. 1211/5 Pushbutton Height from panel: Up to 9/16" Pushbutton Diameter: Up to 1/4" Bushing Diameter: 3/8" maximum Part No. 1211/32 Pushbutton Height from panel: Up to 19/64" Pushbutton Diameter: Up to 1/8" Bushing Diameter: 1/4" maximum P/N 1211/10 P/N 1211/32 P/N 1211/5 Toggle Switch Boots Part No. 1111/4 Bat Handle Height from panel: 7/8" Bat Handle Diameter: Up to 1/4" Bushing Diameter: 15/32" maximum Part No. 1111/9 Subminiature Toggle Boot Bat Handle Heights from panel: Up to 9/16" Bat Handle Diameter: Up to 1/8" Bushing Diameter: 1/4" maximum P/N 1111/4 P/N 1111/9 Rotary Shaft Boots Part No. 1312/7 Shaft Diameter: 1/4" nominal Bushing Diameter: 3/8" maximum Part No. 1312/8 Shaft Diameter: 1/8" nominal Bushing Diameter: 1/4" maximum P/N 1312/7 SNAPSEELв„ў Shouldered Mounting Nut Selection Chart TO INSURE PROPER DESIGN FUNCTION, SNAPSEEL MUST BE USED WITH APM SHOULDER TYPE NUT (SEE CHART FOR SIZES). METRIC THREAD AVAILABLE ON REQUEST. MATERIAL: ALUMINUM P/N 1312/8 APM Part No. (Shouldered Nut) Bushing Thread Size* For use with SNAPSEEL P/N A Dimensions B C 2120/122/1 15/32-32 1211/10, 1111/4 17/32" 3/32" 11/64" 5/8" 2120/122/2 3/8-27 1211/5, 1312/7 13/32" 3/32" 11/64" 1/2" 2120/122/3 3/8-32 1211/5, 1312/7 13/32" 3/32" 11/64" 1/2" 2120/122/5 2120/122/6 2120/122/7 2120/122/9 2120/122/10 1/4-40 M6 x .75 10-48 1/4-32 12-24 1211/32 1111/9 1312/8 9/32" 3/64" 3/32" 5/16" *Other thread sizes available. Please consult factory. 13 D INSTALLATION INSTRUCTIONS FOR THREADED HEXSEAL & E-SEEL BOOTS В® В® IMPORTANT вЂ” CAUTION STEP 3: THREAD RULE DIMENSION A 3 to 4 threads (maximum) for all toggle pushbutton and rotary shaft seals (except N5000 series). A Mounting Hole Mounting Hole Panel Back-Up Nut Switch Housing 2 to 3 threads (maximum) for N5000 series. Switch Housing For proper installation of these boots, follow these five sequential steps. It is EXTREMELY IMPORTANT that the number of threads on the switch/potentiometer bushing EXPOSED ABOVE THE FRONT PANEL SURFACE be within the recommendation (see chart above). Failure to respect these maximums may result in boot damage (such as tearing). A Mounting Hole Panel Back-Up Nut Switch or Potentiometer Housing STEP 1. Remove front mounting nut from switch bushing. STEP 2. Put threaded bushing through panel. STEP 3. Adjust back-up nut to allow the specified number of threads to protrude past front of panel (see Dimension вЂњAвЂќ above). STEP 4. If needed, install appropriate bushing adaptor. STEP 5. Install switch boot in place of front mounting nut. .. . RECOMMENDED INSTALLATION TOOLS: Six point hex socket wrench. Spintite. Adjustable wrench (without serrated jaws). Threaded Bushing Adaptors Inside (Bushing) Thread Size (Class 2B) Outside (Boot) Thread Size (Class 2A) APM Part Number 3/8-32 15/32-32 1/2-32 15/32-32 1/2-24 5/8-24 5/8-24 3/4-32 3/4-20 15/32-32 11/16-32 11/16-32 13/16-32 13/16-32 13/16-32 7/8-32 7/8-32 7/8-32 2500/1/5* 2500/1/7 2500/1/10 2500/1/8 2500/1/9 2500/1/11 2500/1/12 2500/1/13* 2500/1/14* 14 *5/32" thick. Additional sizes, including metric, available. Please consult factory. Material: Plated Brass *Unless otherwise noted. Custom Switch Boots & SealsвЂ¦ APM HEXSEAL tailors special boots for special needs. If your application requires boots not shown in this catalog, please call us for custom design assistance. Your need may be satisfied by an inexpensive variation of a standard product or mold. Whether your application calls for custom colors, other bushing/bezel sizes, alternative boot materials or a totally custom design, let us know. We have satisfied diverse requirements including full seals for an array of switches, transparent panel meter boots, and electronic connector seals. Pick a Shape вЂ¦ Any Shape вЂ¦ For over fifty years, weвЂ™ve tackled a myriad of product-environmental sealing boot configuration challenges. Drawing on our experience with a wide range of exotic elastomers and high-precision molding, and using the latest computer-aided technology, APM has provided practical and economical solutions for the military, industrial and commercial markets. We welcome the opportunity to provide design assistance. Send us your product, specifications or drawings, and weвЂ™ll gladly quote. single-piece silicone rubber keypad seal вЂ¦ Any Application Shown at right are two examples of custom-designed silicone seals for use indoors or out. At top, a single-piece clear silicone rubber seal designed to protect delicate circuitry of the outdoormounted controls for a sophisticated audio system from hostile contaminants such as water, dust, dirt and pollen. Silicone rubber preserves tactile feel of buttons for smooth operation. Below, a single-piece tri-color (black, green and clear) silicone rubber seal designed for a remote automotive keyless entry control. With extensive experience in designing and molding a wide range of elastomers, APM specializes in developing costeffective sealing solutions for electrical and electronic applications. Lighted Pushbutton Switches & Indicators These custom seals protect STACOSWITCHвЂ™s Series 90 lighted pushbutton switches and indicators from penetration from fog, snow, salt spray, sand and dust. Resistant to kerosene, salt water, alcohol and light detergents, these watertight seals also assure the pushbutton remains attached to the switch under highimpact shocks up to 1,500 Gs. Just another example of how APM sealing boots help heighten the performance and reliability of your product. Armored Toggle & Pushbutton Seals Having all the same sealing characteristics of our standard silicone sealing boots, our armored versions feature a stainless steel actuator that wonвЂ™t rust/corrode and meets the stringent requirements of the medical and food processing industries. In addition, the large actuator is ideal for applications where operators wear work or surgical gloves. These easy-to-install units are reusable, less costly, and seal the panel cutout in which the switch is mounted. Custom Keypads YouвЂ™re looking at one of many variations of keypad seals used in telecommunications, security, medical, industrial and other applications where environmental protection is essential for long-term, reliable equipment performance. 15 Also available from APM Hexseal: a complete line of Environmental Sealing Boots for Circuit Breakers. UL Recognized Component Also meets Canadian requirements Ask for Catalog CB Learn more about our other standard and custom productsвЂ¦ Ask for these catalogs: Circuit Breaker Boots Catalog CB Custom Elastomeric Seals Catalog CS Incandescent Lamp Colorizing Filters вЂў Catalog SK Self-Sealing Fasteners Catalog SF200 APM HEXSEAL 44 Honeck Street вЂў Englewood NJ 07631 вЂў Tel.: (201) 569-5700 вЂў Fax: (201) 569-4106 вЂў Web: www.apmhexseal.com SEELSKREWSВ®, SEELBOLTSВ®, SEELRIVETSВ®, & KAPTO-SKREWSВ® are U.S. Registered Trademarks of APM HEXSEAL CORPORATION. Printed in USA APM-9809-25M