Installation & Owner’s Manual U.S. and Canada; call toll-free: Outside the U.S. and Canada; call: 1-877-ROC_N_ROL (1-877-762-6765) +1 (616) 243-3633 E-Mail: [email protected] Web: www.amietertainment.com 22022618 Rev F AMI NGX MINI JUKEBOX WARRANTY AMI extends the original operator of this equipment the following warranty: All parts are guaranteed to be free of defects in material and workmanship for the specific periods listed. AMI agrees to repair or replace without charge during such period any part which proves defective upon examination by AMI. All costs of shipping a defective part to AMI’s offices shall be borne by the original operator. AMI shall bear the shipping costs for the replacement of defective parts. Component Electronic Circuit Boards Core Computer Motherboard Electrical & Mechanical LCD Display Touch Screen Sensor Touch Screen Controller Hard Drives Warranty Period (from date of shipment) 2 Years 1 Year 2 Years 1 Year 1 Year 1 Year Life* Condition Parts Parts Parts Parts Parts Parts *Full Replacement by AMI, at no charge, for the life of the AMI Entertainment® contract. In the case of parts supplied to AMI as components, AMI extends the same warranty period as extended by the original manufacturer. The above warranty applies provided that all parts of the product have been serviced properly as directed in the service manual, and provided the alleged defective part, upon examination by AMI, shall prove to be thus defective. Under no circumstances shall AMI be liable for any incidental, consequential or special damages, losses or expenses arising from or in connection with the use of, or the inability to use, the product for any purpose. AMI reserves the right to make any changes or improvements in its products without notice and obligation, and without being required to make corresponding changes or improvements in products theretofore manufactured or sold. This warranty will not apply to any product or any part which has been subjected to any accident, abuse, or misuse. AMI ENTERTAINMENT NETWORK, LLC EXTENDS NO WARRANTY, EXPRESSED OR IMPLIED, TO PURCHASERS OR USERS OF ITS PRODUCTS EXCEPT AS HEREIN SET FORTH, WHETHER BY OPERATION OF LAW OR OTHERWISE. Table of Contents Important Safety Instructions_________________________________________2 Section A - Jukebox Specifications ___________________________________3 Section B - Placing the Wall-Mounted Jukebox on Location _______________5 Location Power and Warnings ________________________________________________ 6 Jukebox Power and Reset Switch______________________________________________ 7 Wall Mounting Instructions ___________________________________________________ 8 IR Remote Installation Instructions ____________________________________________ 10 Testing the Unit ___________________________________________________________ 11 Lighting Controller _________________________________________________________ 12 Section C - Sound System Set Up ___________________________________13 Extension Speaker Operation ________________________________________________ 14 Selecting Speaker Power ___________________________________________________ 14 Selection Procedures ___________________________________________________ 14 Extension Speakers Connected to Amplifier Channel + and – terminals ____________ 15 Amplifier Overload Check ___________________________________________________ 15 Section D - Service & Maintenance___________________________________19 Recommended Routine Maintenance __________________________________________ 20 Calibrating the Touchscreen _________________________________________________ 21 Hard Drive Replacement ____________________________________________________ 21 Section E - Troubleshooting ________________________________________23 LED Indicators ____________________________________________________________ 24 Troubleshooting Charts _____________________________________________________ 26 Connection Diagrams ______________________________________________________ 28 Section F - Parts Catalog ___________________________________________35 Front Door/LCD Assembly __________________________________________________ 36 Inside Cabinet ____________________________________________________________ 37 Currency Components _____________________________________________________ 38 Electronic Components _____________________________________________________ 39 Accessories ______________________________________________________________ 42 Page 1 Important Safety Instructions 1. Read these instructions. 9. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 2. Keep these instructions. 3. Heed all warnings. 10. Only use the attachments/accessories specified by the manufacturer. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 11. Use only with the bracket specified by the manufacturer or sold with the apparatus. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the jukebox. WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. No objects filled with liquid, such as vases, shall be placed on the apparatus. AVERTISSEMENT Pour réduire le risque d'incendie ou un choc électrique, ne pas exposer cet appareil à la pluie ou à l'humidité. Aucun objet rempli de liquide, comme les vases, ne doit être placé sur l'appareil. CAUTION! RISK OF ELECTRIC SHOCK. DO NOT OPEN DO NOT REMOVE ANY COVERS, GUARDS, OR SHIELDS. NO USER SERVICEABLE PARTS ARE INSIDE THIS JUKEBOX. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ATTENTION! RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR NE JAMAIS RETIRER LES COUVERCLES, GARDES, OU DES BOUCLIERS. AUCUNE PIÈCE RÉPARABLE DANS CE JUKEBOX. CONFIER L'ENTRETIEN DE PERSONNEL QUALIFIÉ. Page 2 Section A Jukebox Specifications NGX MINI Dimensions: Uncrated: Height Width Depth Crated: Height Width Depth 31” 18.375” 8.5” 35” 22.5” 11.5” Weight: Uncrated 75 lbs. Crated 90 lbs. Amplifier: Output Power: (Standard) Protection: 500 Wrms into 4 Ohm Load Thermal and speaker overload Automatic, self resetting Voltage: Frequency: 115VAC 60Hz LCD: 19” flat screen Speakers: none Page 3 This page is intentionally left blank. Page 4 Section B Placing the Wall-Mounted Jukebox on Location • Location Power and Warnings • Jukebox Power and Reset Switch • Wall Mounting Instructions • IR Remote Installation Instructions • Testing the Unit Page 5 Location Power and Warnings ! The jukebox must have a clean source of properly-phased and grounded 115VAC power at 10 amps max. This MUST be provided 24 hours a day, 7 days a week. The outlet the jukebox is connected to must NOT be controlled by a switch, nor should the circuit breaker feeding it be shut off at night. If the outlet is not properly phased, grounded, or is connected to an overloaded circuit, it must be corrected by a qualified electrician before using. The main power distribution unit is the power supply. This device contains a combination main circuit breaker/power switch along with surge protection. ATX RESET SWITCH POWER SUPPLY COMPUTER CORE ASSEMBLY (SERVICE, REJECT, CALIBRATE, POWER BUTTON LOCATION) MAIN POWER ON/OFF SWITCH Figure 1-B – Inside View of Cabinet with Front Door Opened Page 6 Jukebox Power and Reset Switch Hard Power Down The NGX MINI jukebox is powered from a standard 115VAC wall plug using the provided power cord. Inside the jukebox, power is routed to a power distribution assembly located on the left-hand side of the cabinet (see Figure 1-B). This assembly includes a combination 15A circuit breaker/power ON/OFF switch. All other components in the jukebox are powered by plugging them into this power distribution assembly. When the jukebox power cord is unplugged or the main power ON/OFF switch is turned off (see Figure 1-B), the jukebox is in the hard power down state. All power is removed from all components in the jukebox. ATX Reset Switch There is a hidden ATX reset switch located inside the cabinet on the upper-left side just below the cooling fan (see Figure 1-B). It is accessible by either opening the jukebox door, or by inserting a paper clip, toothpick, or other long, thin object through the access hole on the left side of the jukebox. Soft Power Down The Core Computer and other components in the jukebox should remain powered up at all times. However, there may be times when the jukebox needs to be turned off so that customers cannot insert money or make selections. The soft power down mode will give every outward appearance that the jukebox is off by turning off the lights, the LCD display, the bill acceptor(s), and the credit card reader; however, the Core Computer and other internal components remain powered up. There are multiple ways to enter and exit this soft power down mode: • Core Computer Power Button – The button labeled “POWER” on the Core Computer inside the jukebox (see Figure 1-B) is used to enter the soft power down mode. Push it again to exit the soft power down mode. • IR Remote Control – The button labeled “POWER” on the IR remote control transmitter will also toggle the soft power state just like the button described above. • 6 Button Wired Volume Control – This control can be modified to provide a POWER function. See Wired 6 Button Volume Control on page 13 for details. • Computer Core The jukebox Computer Core can be powered off by pressing the “SERVICE” button on the Computer Core (see Figure 1-B), and then touching “Shutdown Jukebox” on the touchscreen. This will turn off the Computer Core and other components that get their power from the ATX power supply in the Computer Core. To restore power after turning off the ATX power supply, the jukebox must be rebooted. Reboot the jukebox by toggling off the main power ON/OFF switch (see Figure 1-B) and then toggling it back on, or by pushing the ATX Reset Switch (see “ATX Reset Switch”). Page 7 The ATX Reset Switch resets the Computer Core. This is like the reset switch on a PC. Pressing and releasing this switch will cause the computer main board to completely reboot. Use this switch only if the jukebox is completely non-responsive. Additionally, when the Computer Core has been powered down using the “Shutdown Jukebox” option in Service Mode, pushing this button will restart the computer. Wall Mounting Instructions Choosing the Location WALL STUD The jukebox must be mounted on a strong, flat wall. It is recommended that a sub panel made from ¾” plywood or similar material be used and properly shimmed to provide a flat mounting surface. The jukebox should be visible and convenient to use. Do NOT install directly above a radiator or other source of heat. Be sure the speaker wires can be easily run to the unit. UPPER KEYHOLES (SHOULD BE 65" FROM THE FLOOR) MOUNTING HOLES WARNING The mounting of the jukebox on the wall should be done by a qualified installer familiar with wall construction and loading. The wall and installation hardware MUST be capable of supporting a 700 lb. load for the NGX MINI. Failure to follow these instructions could result in serious injury. Tools and hardware required for normal installation into wood wall studs: • Socket wrench with 3/8” and 7/16” sockets • Level • Pencil • Punch or awl (to start the lag screws) and/or drill driver • (4) 1/4” x 1-1/2” lag screws provided Figure 2-B – Inside View of the Cabinet 5. Remove the jukebox cabinet from its packing carton. Open the door, ensure all cables are detached from the door, and then lift the door off of the cabinet. Set the door aside for the moment. 2. Install a subpanel or locate a wall stud roughly in the center of where the jukebox will be mounted. See Figure 2-B. 3. Install the first ¼” x 1½” lag screw 65” up from the floor. If not using a subpanel, center the lag screw on a wall stud. This should be on the centerline of the jukebox. See Figure 2-B. 4. Hang the jukebox cabinet on this lag screw using one of the upper keyholes in the back of the jukebox cabinet (see Figure 2-B). Ensure the jukebox cabinet is level and mark the wall for the lower keyhole and the mounting holes in the top right and top left of the cabinet (See Figure 2-B). Remove the jukebox cabinet from the wall, drill pilot holes for the remaining lag screws, re-hang the jukebox cabinet and secure it to the wall using the additional lag screws provided. NOTE: If the wall is concrete, cinder block, brick, or uses metal wall studs, then a subpanel with the appropriate fasteners must be used. At least 4” heavy-duty fasteners (one in each corner) must be employed. The fasteners and subpanel must be able to support a minimum 150 lbs. Do NOT use “press-in” anchors or any other “light” or “medium” duty fasteners. Consult a contractor experienced in the type of construction used if there is any doubt about the strength of the mounting devices. Mounting the Jukebox Cabinet 1. LOWER KEYHOLES FOR MOUNTING JUKEBOX DIRECTLY TO STUD WALL, AMI RECOMMENDS A THIRD LAG SCREW INTO STUD 6. Page 8 Prepare the external wiring. The power cord, speaker wiring, and Ethernet cable can be routed to enter the top or the bottom of the jukebox. Use the block-out plates and nuts to secure the wiring. 8. The front door is secured using slide hinges, which do not require tools to attach. To attach the front door, carefully lift the door, line up the hinge pins on the cabinet with the mating hinge barrels on the front door, and lower the door (see Figure 3-B). 9. Locate the bundle of cables taped to the inside back of the cabinet. Route the cable bundle to the front door and into the cable clamp in the middle of the door near the door’s hinge (see Figure 4-B). Connect the LCD power, VGA, and serial cables to the back of the LCD. HINGE BARREL ON FRONT DOOR 10. Connect the free end of the credit card reader cable (coming from the USB port on the Computer Core) to the card reader. See Figure 4-B. DOOR 11. Connect the free end of the cable from the VCU jack on the Computer Core to the light interconnect board (see Figure 4-B). CABINET 12. Connect the free ends of the 15-pin cables from the cabinet and door together (see Figure 4-B). HINGE PIN ON CABINET 13. Make sure all cables are dressed properly. Use the cable clamps in the jukebox to keep cables in place. Make sure nothing interferes with opening and closing the door. Figure 3-B – Detail View of Top Cabinet Hinge LCD POWER CABLE VGA CABLE SERIAL CABLE 15-PIN CONNECTORS (FOR BILL, COIN, AND LIGHTS) CABLE CLAMP USED TO ROUTE WIRES FROM CABINET TO DOOR LIGHT CABLE CONNECTED BETWEEN LIGHTS INTERCONNECT BOARD AND “VCU” JACK CREDIT CARD CABLE CONNECTED BETWEEN CARD READER AND USB PORT Figure 4-B – Inside View of NGX MINI Jukebox with Front Door Opened Page 9 IR Remote Installation Instructions IR Remote Control Installation Instructions Wired 6 Button Volume Control The Continental Video Jukebox comes with an IR remote (located in the Handy Pack). To install, plug the provided cable into the provided IR remote receiver (see Figure 10-B) and route the other end of the cable through one of the wire access holes in the cabinet. Connect the end of the cable into the port labeled “IR Receiver” on the Core Computer. Install the IR remote receiver above the jukebox, with a clear line of sight between the receiver and the handheld transmitter. Plug in and turn on the jukebox and test the remote. The Continental Video Jukebox also comes with a small 6 button wired remote control. This control is designed to be mounted close to the jukebox and provides some basic functions. INT. These buttons change volume for Channels 1 & 2. EXT. These buttons change volume for Channels 3 & 4. CANCEL This button will cancel the selection currently playing. CABLE CONNECTED TO TOP OF RECEIVER MUTE This button toggles the jukebox between PAUSE mode and PLAY mode. RECEIVER MUST BE INSTALLED WITH SENSORS FACING FRONT Figure 10-B – IR Remote Receiver Button Functionality on the IR Remote Transmitter To enable or disable options on the IR remote, see “IR Remote Setup” in the Network Setup, Jukebox Operation, Operator Setup Screens Manual. The MUTE button on this remote can be repurposed to function as a POWER button. REJECT This button is used to cancel (or “reject”) the selection currently playing, and cancels all (rejects all) selections in the queue if held down for four seconds. This functionality can be enabled and disabled through the software. Remove the back cover of the remote control then remove the circuit board. There are two shut jumpers located on the board. When these jumpers are both in the right hand position, the MUTE button functions as MUTE. POWER This button turns the lights, the LCD display, the bill acceptors, and the credit card reader ON/OFF. To turn them back on and resume normal operation, press the “POWER” button again. Move both shunt jumpers to the LEFT hand position to repurpose the MUTE button to function as a POWER button. VOLUME The CH1+ and CH2+ buttons raise the volume. The CH1– and CH2– buttons lower the volume. The PLAY button puts the jukebox in play mode. The PAUSE button puts the jukebox in pause mode for a programmed amount of minutes or until the PLAY button is pushed. The AP OFF and AP ON buttons turn any programmed Autoplay mode on/off. The FUTURE button is used to give a remote credit. The VID SEL button is used to enable and disable video selections on the jukebox. Page 10 Testing the Unit Initial Set Up has two) and check the screen to make sure proper credit is awarded. 5. To test the coin acceptor, deposit U.S. quarters into the coin slot and verify proper credit is awarded. 6. To test the credit card reader, swipe a valid credit card and check that the screen displays the last four digits of the credit card. 7. When finished, touch the Back button to return to the Main Menu. When all of the network connections have been made, boot up the jukebox. The first time you turn on the jukebox with a new hard drive, you will see the Local Music Configuration Screen, which lists the available local music configurations that can be installed on the jukebox. You will be prompted to select one of the available lists. This selection can be changed at any time by pressing the SERVICE button on the Computer Core, and then touching System Setup -> Advanced Administration -> Local Music Configuration. Touch the View button to display a dialog box listing all of the albums in the selected list. Some albums may appear grayed out; this means that some or all of the songs in the album are not currently stored on this jukebox. If a list with grayed albums is installed, the grayed albums will start being downloaded to the jukebox within 24 hours (as long as the jukebox is connected). If the jukebox becomes disconnected, any songs not yet downloaded will be unavailable to patrons. Touch the Install button to display a dialog box prompting you to install the selected list. To install the selected list, touch the Install button at the bottom of the dialog box. Testing the Network Enter Service Mode by pressing and releasing the “SERVICE” button on the Computer Core. To test the network: 1. Touch the System Setup button on screen and then touch Advanced Administration. 2. On the Advanced Administration Screen, touch Configure Server. Then touch the Test Connection button. This test confirms the jukebox can connect to AMI’s server (“Server Found”), and authenticate a connection with AMI’s server (“Connected”). 3. If the connection is successful, you will see “Yes” next to “Server Found” and “Connected”. If the connection fails, you will see “No”. If the connection fails, check the settings on the Network Information Screen (Diagnostics –> Network Information). This screen will allow you to check the IP Configuration and run LAN and WAN tests. Testing the Touchscreen, Bill and Coin Acceptor(s), and Credit Card Reader Touchscreen – Every time a new hard drive is installed, the touchscreen should be calibrated. Follow these steps to calibrate. 1. Press the “CALIBRATE” button on the Computer Core (see Figure 1-B) to launch the calibration program. 2. Close the jukebox door and make sure it is locked. 3. Follow the directions on the screen, touching the center of the targets, and then touching different areas on the screen. If the cursor follows your movement, touch YES to exit. Testing the Audio NOTE: For operators pre-testing the jukebox in their own facility, any features in the application associated with the network will not work unless the jukebox is connected to the Internet. 1. If the jukebox is not in Service Mode, press the “SERVICE” button on the Computer Core to enter Service Mode. 2. Add one (or more) credits to play a song and test the audio. Touch Cash Management and then touch Credit Management. 3. Touch the box under “Credits” and a pop-up box will display. 4. Touch Clear to remove the “0” from the box. 5. Touch 1 (or more) and then touch Update. 6. Touch Save on the Credit Management Screen. 7. Touch Exit Service Mode. 8. After connecting speakers to the jukebox (see section C), play a local music selection to test the audio. Bill/Coin Acceptor(s) and Credit Card Reader – (NOTE: Credit Card functionality requires a broadband Internet connection). 1. Press the “SERVICE” button on the Computer Core to enter Service Mode. 2. Touch the Diagnostics button. 3. Touch Credit Device Tests. 4. To test the bill acceptor(s), insert a $1, $5, $10, and $20 bill (into each bill acceptor, if the jukebox Page 11 Lighting Controller The NGX MINI lighting assembly can be programmed for several different modes of operation. By default, the lighting assembly is set to slowly cycle through six different colors with a slow transition between each color. There are two blue pots on the board marked BRIGHT and SPEED. These are used to set the brightness of the LEDs and adjust the speed of color changes for the two-color cycling modes. The four position DIP switch is used to set the operating mode of the controller. Use the following table to set the mode. To change the mode, open the main door of the jukebox. The lighting assembly will swing open with the door. Use a Philips screwdriver and remove the LED controller cover from the back right side of the lighting assembly. This exposes the LED controller. SW1 OFF OFF OFF OFF OFF OFF OFF OFF ON SW2 OFF ON OFF ON OFF ON OFF ON OFF SW3 OFF OFF ON ON OFF OFF ON ON OFF SW4 OFF OFF OFF OFF ON ON ON ON OFF Mode Cycle – slow transition through colors (default) Blue Cyan Green Cycle – quick transition through colors Yellow Magenta Red White Page 12 Section C Sound System Set Up • Extension Speaker Operation • Selecting Speaker Power • Speaker Connection Diagrams Page 13 Sound System Set Up The NGX MINI jukebox sound system is powered by an ICEpower 250ASX2 Class 2 power amplifier manufactured by Bang & Olufsen. Speaker terminals are provided to connect extension speakers directly to the amplifier. An Audio Output Transformer Kit (part number 22180806) is available if your installation uses 70 volt speakers or you need to connect extension speakers using various power taps. Extension Speaker Operation To avoid poor sound quality, care must be taken when adding extension speakers. The following requirements must be met: • Speakers connected to the amplifier must be wired so the power consumed by the extension speakers does not exceed the amplifier power rating of 250 watts per channel. • Complete the Extension Speaker Worksheet (Table 1-1) for each channel and verify it does not exceed the 250 watt amplifier channel rating. After wiring the speakers, perform the Amplifier Overload Check immediately following Table 1-1. • All speakers must be connected with the correct polarity (see Figure 1-A). • Do not bridge output channels. Low Impedance Speakers Low impedance speakers (16, 8, or 4-ohm) can be used when the connecting cable is less than 100 feet. Keep the following two things in mind when wiring your speakers: 1. No more than one 4-ohm speaker should be connected to a speaker line. If several 4-ohm speakers are to be used, each speaker should have its own line. 2. The loss in 100 feet of 18-gauge zip-cord feeding on an 8-ohm speaker is 15%. The loss for two 8-ohm speakers is 30%. Selecting Speaker Power General Instructions This section will lead you through the power and speaker selection process. This process consists of three major steps and several smaller steps. The major steps are: 1. Identify the extension speakers and compute the speaker power for speakers connected directly across the amplifier. 2. Make the extension speaker connections. 3. Perform an amplifier overload check (see instructions immediately following Table 1-1). Selection Procedures • Use a pencil (you may want to revise your figures) to fill in the Extension Speaker Worksheet on the following pages. • Use the Table 1-1 Worksheet to help you calculate the amount of power consumed by the extension speakers. An extension speaker RMS power rating should be at least 10% higher than the power it will consume at maximum jukebox volume. • When RMS power to speaker at maximum jukebox volume is: Then recommended RMS power rating of speaker is: 240 watts 120 watts 60 watts 30 watts 300 watts 150 watts 75 watts 40 watts Page 14 Table 1-1 – Extension Speaker Worksheet Sheet 1 Extension Speakers Connected to Amplifier Channel + and – terminals Place the quantity of speakers in the blank under Qty and multiply the quantity times the power consumption. Place your results in the blank under Total. Qty CH 1 Two 8-ohm speakers in series: (30 watts to each speaker) Two 4-ohm speakers in series: (60 watts to each speaker) 8-ohm speakers: 4-ohm speakers: Total CH 2 CH 1 CH 2 ______ ______ at 60 watts per series = ______ ______ watts ______ ______ at 120 watts per series = ______ ______ watts ______ ______ ______ at 120 watts each = ______ at 240 watts each = ______ ______ ______ watts ______ watts ______ ______ watts Total Load, sum Total columns for CH1 and CH2 Amplifier Overload Check Check that the amplifier is not overloaded by performing the following steps: 1. Make sure that the extension speakers are connected to the amplifier terminals properly (Channel1 + – and Channel 2 + –). 2. If the red OVERLOAD LED is always lit, the amplifier is overloaded and will shut down. You must perform Step 3. 3. Do this step only if the OVERLOAD LED came on as described in Step 2. • Find the source of the overload (shorted speaker wires, shorted speaker, too many speakers connected). • After you fix the short, disconnect a few speakers to reduce the wattage. Repeat Step 2. • If no overload is detected, reconnect the disconnected speakers (ensure you do not have too many speakers, use Table 1-1). Repeat step 2. Page 15 NOTE: SPEAKER WATTAGE SHOWN IS RATING OF SPEAKER Channel 1 + + 8 Ohms + 150 W 8 Ohms 150 W Channel 1 Load as shown is 240 W per channel. Maximum pow er capacity is achieved. Channel 2 + Channel 2 - + 8 Ohms + 150 W 8 Ohms 150 W Amplifier + + 8 Ohms 150 W Channel 1 + 8 Ohms 50 W + 8 Ohms 50 W Channel 1 - Load as shown is 180 W per channel Channel 2 + + Channel 2 - + 8 Ohms 150 W Amplifier 8 Ohms 50 W + 8 Ohms 50 W + + 8 Ohms 150 W Channel 1 + 4 Ohms 75 W + 4 Ohms 75 W Channel 1 Load as show n is 240 W per channel. Maximum power capacity is achieved. Channel 2 + + Channel 2 - + Amplifier 8 Ohms 150 W 4 Ohms 75 W + 4 Ohms 75 W Figure 1-C Page 16 NOTE: SPEAKER WATTAGE SHOWN IS RATING OF SPEAKER + + 16 Ohms + 75 W 16 Ohms + 75 W Channel 1 + + 8 Ohms 50 W Channel 1 - Load as shown is 240 W per channel. Maximum power capacity is achieved. Channel 2 + Channel 2 - + + Amplifier 50 W 16 Ohms 75 W 8 Ohms 16 Ohms + 75 W 16 Ohms + 75 W 50 W 16 Ohms 75 W 8 Ohms + 8 Ohms 50 W + 8 Ohms + 50 W Channel 1 + + 8 Ohms + 50 W 8 Ohms + 50 W 8 Ohms 8 Ohms + 50 W + 50 W 8 Ohms 8 Ohms 50 W + 50 W 8 Ohms 50 W Channel 1 Load as shown is 240 W per channel. Maximum power capacity is achieved. Channel 2 + Channel 2 - + Amplifier 8 Ohms + 50 W + 8 Ohms + 50 W 8 Ohms + 50 W 8 Ohms 50 W Figure 1-C (continued) Page 17 8 Ohms + 50 W + 8 Ohms 50 W 8 Ohms 50 W + 8 Ohms 50 W This page is intentionally left blank. Page 18 Section D Service & Maintenance • Recommended Routine Maintenance Page 19 Recommended Routine Maintenance Heat is the biggest enemy of electronic components. Proper maintenance is essential for maximum earnings and reliability. It is very important to keep all cooling fans clean. Once dust and dirt is visible on a cooling fan, the airflow is reduced by at least 25%. There are several cooling fans in the cabinet (see Figure 1-D). 4. Slide the bill stacker back on the bill acceptor. Be sure the green light is on (for MEI, make sure the green lights/arrows are flashing). 5. Close and lock the jukebox door. Minor Service Perform these steps a minimum of every 3 months if operating more than 14 hours per day, operating where smoking is allowed, or operating in a dusty environment. Perform these steps a minimum of every 6 months if operated less than 14 hours per day and in a very clean environment. You will need a new, soft 2” paintbrush*. 1. Gently brush* dirt from the cabinet cooling fan. Verify fan operation. 2. Brush* dirt from the amplifier fan. Verify fan operation. 3. Check the operation of the CPU fan from the “Health Status” Screen. 4. Listen to the CPU fan for excessive noise or vibration. 5. Clean the bill acceptor with an approved cleaning card. 6. Clean the credit card reader with an approved cleaning card. 7. Clean and calibrate the touchscreen (see the next page for calibration instructions). Recommended preventative maintenance Routine Service The following steps take about 3 minutes and should be performed at each collection. 1. Check the CPU fan from the “Health Status” Screen. 2. Ensure the cabinet fan on the upper-left side of the cabinet is blowing air out and the fan looks clean. See Figure 1-D. 3. Be sure that nothing is resting on top of the unit or otherwise blocking the airflow around the machine. CABINET FAN Cleaning the Touchscreen Any standard glass cleaner can be used to clean the touchscreen. Always spray the glass cleaner on the cloth or towel and not directly on the touchscreen. Glass cleaner sprayed directly on the screen could possibly leak inside and cause damage. CPU FAN INSIDE COMPUTER CORE Cleaning the Door Panel The door panel is made of polycarbonate. We recommend cleaning with a mild cleaner and a soft cloth to avoid scratching the surface. Annual Service The following steps should be performed every year in addition to everything in the minor service section. 1. Vacuum the interior of the cabinet and fans. 2. Inspect the power cord for fraying or damage. 3. Check the power ground. 4. Check all LAN connections and wiring. 5. Listen to all speakers to make sure they are operating correctly. Figure 1-D – Inside View of Cabinet Collecting from the Bill Acceptor 1. Unlock and open the front door. 2. To remove the bill stacker, slide the tab on the back of the bill acceptor towards the front door and push the stacker forward and then upward. 3. Open the side door on the bill stacker to remove the cash. Scheduled maintenance always costs less time and money than an unscheduled breakdown. Page 20 Calibrating the Touchscreen Hard Drive Replacement Every time a new hard drive is installed, the touchscreen should be calibrated. Follow these steps to calibrate. 1. Turn off and unplug the jukebox. 2. Loosen the thumbscrew securing the cover on the Computer Core and slide it off (see Figure 4-D). 1. Press the “CALIBRATE” button on the Computer Core (see Figure 2-D) to launch the calibration program (see Figure 3-D). Calibrate Figure 4-D – Computer Core Figure 2-D – Computer Core 3. Carefully slide the hard drive tray out of the assembly as far as cabling will allow. 4. Disconnect the SATA power and data cables from the drive. 5. Connect the SATA power and data cables to the new hard drive. 6. Slide the hard drive back into the assembly. Make sure not to pinch any cables while doing so. 7. Replace the Computer Core cover and secure it with the existing thumbscrew. Figure 3-D – Calibration Screen 2. Close the jukebox door and make sure it is locked. 3. Follow the directions on the screen, touching the center of the targets, and then touching different areas on the screen. If the cursor follows your movement, touch YES to exit. Page 21 This page is intentionally left blank. Page 22 Section E Troubleshooting • LED Indicators • Troubleshooting Chart • Connection Diagrams Page 23 LED Indicators The LEDs are described below to help you isolate a problem. COMPUTER CORE ASSEMBLY (61197002) USB Tx LED – It should be flashing, indicating good communication between the motherboard and the I/O board. USB Rx LED – It should be flashing, indicating good communication between the motherboard and the I/O board. STATUS LED – Flashes three times on power up, but otherwise it should be off. RS485 Tx LED – It should be flashing, indicating good communication between the I/O board and Rowelink devices such as the Amplifier and Volume Control Units. RS485 Rx LED – It should be flashing, indicating good communication between the I/O board and Rowelink devices such as the Amplifier and Volume Control Units. IR RECEIVER LED – Flashes when an IR signal is received. +5VDC – Indicates this voltage from the ATX power supply is present. +12VDC – Indicates this voltage from the ATX power supply is present. HDD LED (RED) – Flashes when the motherboard is accessing data on the hard drive. PWR LED (GREEN) – When lit, indicates the power supply in the core computer assembly is on. POWER SUPPLY ASSEMBLY (40991404) POWER (Green) – When lit, indicates power is applied to the Amplifier. STATUS (Red) – Indicates the status of the Preamplifier/Amplifier, normally on. COM (Green) – Quick flashes indicate communication with the Core Computer is OK. MUTE (Red) – Indicates the mute status of the Amplifier (On = muted, Off = not muted) OVERCURRENT – When lit, indicates the Amplifier is overloaded. Verify speaker load and ensure there are no shorted speaker wires. THERMAL – When lit, indicates the Amplifier is overheating. Be sure the cabinet fan(s) are working, the filters are clean, and nothing is blocking air flow through the cabinet. Page 24 Preamplifier STATUS – normal operation The STATUS LED is used to indicate the status of the preamplifier. Under normal conditions the STATUS LED will flash once on power up, stay off for a second, and then turn back on and stay on. If either of the two microphone inputs become active, either by activation of the SENSE line or by the Voice Activation Circuits, the STATUS LED will blink on and off at a 150ms rate until the microphone circuits become inactive. Preamplifier STATUS – error conditions The STATUS LED is used to indicate possible faults on the preamplifier board. During power up, the preamplifier runs a self test. If a fault is detected, the STATUS LED is used to indicate what may be wrong. The LED will repeat a pattern of a specific number of blinks. The blink pattern is 500ms on, 500ms off and then one to seven quick 100ms on blinks, three seconds off. The blinking pattern will repeat until the preamplifier is reset or power is turned off. Number of blinks 1 2 3 4 5 6 7 Problem Description Digital Audio Processor did not come out of RESET Digital Audio Processor COM error EEPROM COM error Digital Audio Processor memory load error EEPROM data error Digital Potentiometer COM error in Mic circuit 2 I C SDA line is stuck low If the DAP fails during normal operation, after power up the STATUS led will start to blink one second on, two seconds off, continuously until power is cycled or until the DAP failure goes away. Page 25 Troubleshooting Charts The best way to isolate a problem is to determine its cause. The following charts should help to narrow down which module is failing and whether it can be fixed or it needs to be replaced. Start with finding the “Problem” column that relates the closest to the problem you are experiencing and then match it to the closest “Symptom”. There can be many “Probable Causes” listed for each Symptom. The Probable Causes are listed in decreasing order of probability. PROBLEM The Windows operating system does not boot up. SYMPTOM At the first boot up screen, “Detecting IDE Primary Master” reports “None”. The LEDs on the Computer Core come on, but the screen stays dark. PROBABLE CAUSE 1. There is no hard drive in the Computer Core. 2. The plugs are not completely seated in the hard drive. 3. The data cable or power cable has come loose from the motherboard or hard drive. 1. There is no hard drive in the Computer Core. 2. The data cable or power cable has come loose from the motherboard or hard drive. 3. The hard drive is faulty. 1. The plug is not completely inserted into the outlet. 2. The wall circuit is not “hot”. 3. The ON/OFF switch on the power supply is in the OFF position. 4. The ATX power supply in the Computer Core is faulty. 1. The power plug to the display is not seated completely. 2. The power distribution assembly is defective. 3. The LCD is faulty. The LCD briefly shows “NO CABLE” or “NO VIDEO SIGNAL”. The touchscreen does not work. The computer fan is on and all system’s LEDs and lights are normal. 1. The video cable wiring is not seated completely. 2. The LCD is defective. 3. The Computer Core is defective. The application boots up, but the touchscreen does not respond to touch. The touchscreen will not calibrate. Nothing happens after pressing the calibration button. The calibration program runs, but will not respond to touch. No music from jukebox. No sound from jukebox, although the application reports “Now Playing…a New Song.” 1. The USB cable is not seated completely at the LCD or at the Computer Core. 2. The touchscreen is not calibrated. 3 The touchscreen is defective. 1. The I/O interface board in the Computer Core is faulty. 2. The hard drive is faulty. 3. The Computer Core is faulty. 1. The USB cable plug is not fully seated at the LCD or at the Computer Core. 2. The touchscreen controller is faulty. 3. The touchscreen sensor (glass) is faulty. 4. The motherboard in the Computer Core has failed. 1. Volume control is turned all the way down. 2. The audio mode input routing or muting is configured incorrectly. 3. Audio cables are disconnected or loose from the Computer Core or the preamplifier. 4. Volume control is broken. 5. The amplifier is overloaded and shutdown. 1. There are no more credits available for play. 2. Reject song was activated. The boot up process stops at “DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER.” The LCD screen stays dark when the jukebox is powered up. The PWR LED on the Computer Core does not light. No sound from jukebox and the application doesn’t appear to be playing the song selected. Page 26 PROBLEM Machine is locked up during normal runtime. The bill acceptor does not work. SYMPTOM Bill acceptor is taking money but credits are not accumulating, the touchscreen is not responsive, and I/O board LEDs are not flashing. Lights on the bill acceptor are lit, but the bill acceptor will not accept a bill. The lights on the bill acceptor are not flashing. PROBABLE CAUSE The Computer Core is locked up. Reboot it by pressing and releasing the ATX Reset Switch. If the Computer Core does not boot up, perform a complete Power Down and Power Up. 1. The bill acceptor bill box is full. 2. The bill box was not re-installed on the bill acceptor correctly. 3. There is a jammed bill in the device. 4. The plugs are not inserted securely at the acceptor. 5. The bill acceptor is defective. 1. The cable is damaged at the acceptor. 2. The jukebox has disabled the bill acceptor. Put the jukebox into normal operating mode. 3 The bill acceptor is defective. 1. The inside wiring installation appointment was not scheduled. 2. The inside wiring installation has not occurred. 3. The line was not installed in the pre-selected location. 4. The line (jack) was not labeled by the technician. Location network line not installed in the location. There is no designated broadband line installed in the location. Router does not work. When the power supply is connected to the router, nothing happens. 1. The AC power plug is not fully inserted in the receptacle on the back of the router. 2. Router reset circuit in power distribution assembly is defective. The “Link/Act #” light (on the front of the router) does not light up when an Ethernet cable is plugged in the respective port. The WAN light does not light up. 1. The cable is loose at the Computer Core or router. 2. The jukebox is not powered on. 3. The Ethernet port is defective. The “Music On Demand” feature does not work. The feature has never worked in the location before. The feature did work at one time, but is no longer available. 1. The broadband connection is not plugged into the WAN port. 2. The cable modem or DSL modem is not powered on. 1. There is no Ethernet cable connection between the router and the jukebox. 2. The Ethernet cable is not fully seated in the port on the Computer Core or in the back of the router. 3. The connection is loose between the installed line and the router. 4. The cable is bad. 5. The Internet line is down. 6. The hard drive trigger code was not entered. 1. The connection has become loose between the router and the jukebox. 2. The connection has become loose between the installed line (jack) and the router. 3. All the lights on the front of the router are ON. 4. The router was shut off or lost power. 5. The Internet service provider (ISP) is down. 6. The AMI Entertainment server is down. Page 27 Connection Diagrams NGX MINI COMPUTER CORE SCHEMATIC (PAGE 1) Page 28 RING TIP --1 2 --- NC MUTE B A +12 V GND 1 2 3 4 5 6 To Preamplifier NC MUTE B A +12 V GND 1 2 3 4 5 6 To Lighting Assy Interface NC +12 V IR IN GND LED OUT NC 1 2 3 4 5 6 To IR Receiver RTN-A RTN-B RTN-C STR-A STR-B STR-C 1 2 3 4 5 6 To 6 Button Volume Control GND +12 V COIN 5 COIN 6 LED ON INHIBIT COIN 1 COIN 2 COIN 3 COIN 4 1 2 3 4 5 6 7 8 9 10 OPTIONAL USB RJ11 56K MODEM 1 2 3 4 5 6 7 8 9 10 A1 A3 A5 A7 A9 A2 A4 A6 A8 A10 USB (2) 61196901/03 I/O BOARD GREEN ROWELINK 1 2 3 4 5 6 7 8 9 10 GREEN BUTTONS SERVICE REJECT IR REMOTE YELLOW CALIBRATE 1 2 3 4 5 POWER JUMPERS COIN MECH TYPE 6 BUTTON REMOTE RED OPTOs SWITCHs 4 CH 2 CH PREAMP TYPE COINS Y ES SW PREAMP ENABLE NO INDICATOR LEDs USB Tx USB Rx STATUS RS-485 Tx RS-485 Rx IR RECEIVE +5 VDC +12 VDC +12 V GND GND +5 V Y B B R 1 2 3 4 +12 V GND GND +5 V ATX POWER NC 1 NC 2 GND 3 OOS 4 BILLS +5 V 5 NC 6 CREDIT 7 ESCROW 8 ENABLE 9 DATA 10 CABINET FANS GND GND POWER POWER SPARE IN A SPARE IN B MUTE OUT LIGHTS ON/OFF +12 V GND JUKEBOX I/O GND GND SPECIAL EVENT SPARE OUT B ROUTER POWER SPARE OUT A MONEY METER +12 V 1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 GREEN GREEN YELLOW RED To Coin Mech (if installed) BLUE To Bill Acceptor (if installed) WHITE To Cabinet Fan(s) To Jukebox Power Supply and Other Jukebox Devices NGX MINI COMPUTER CORE SCHEMATIC (PAGE 2) Page 29 BROWN 21958306 TRANSMITTER 40846302 IR RECEIVER TO IR REMOTE (Y ELLOW) ON CORE COMPUTER 34037905 CANCEL TO 6 BUTTON REMOTE (RED) ON CORE COMPUTER INT 62009-A-LF 22160812 19" FLAT PANEL DISPLAY AND TOUCH SCREEN EXT MUTE INCLUDES CABLES MARKED WITH ** 70004-1A WIRED REMOTE TO SERIAL ON CORE COMPUTER SERIAL TOUCH CONTROL **34038702** VGA VIDEO **22164202** TO VGA ON CORE COMPUTER 120 VAC POWER OPTIONAL 34032904 ROWELINK VOLUME CONTROL KIT 34037908 34102004 CH2 CH3 CH4 **21121225** MIC1 MIC2 MIC3 SINGER VOLUME 22322402 TO CORE (GREEN) CH1 ROWELINK SPLITTER (GREEN) TO AMP OR LIGHTING ASSY PWR CAN FUT MODE 28280004 4-PORT WIRELESS ROUTER POWER PLUG TO LOCATION INTERNET SOURCE TO RJ45 ETHERNET ON CORE COMPUTER WAN PORT 1 ETHERNET CABLE SUPPLIED WITH ROUTER KIT 2 OPTIONAL 26704801 WIRELESS ROUTER KIT NGX MINI WIRING DIAGRAM (PAGE 1) Page 30 LAN PORTS 3 4 SERVICE SW SPARE IN B MUTE OUT LIGHTS ON/OFF +12 V GND GND GND SPECIAL EVENT SPARE OUT B ROUTER POWER SPARE OUT A MONEY METER +12 V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 G B BL 40984201 TO JUKEBOX I/O (BROWN) ON CORE COMPUTER R1 10K TO ATX POWER OUT ON CORE COMPUTER G 1 2 3 4 +5 V TO ATX POWER INPUT ON CORE COMPUTER R-3 To Pin 11 B/W-3 To Pin 12 R-2 To Pin 9 B/W-2 To Pin 10 To Pins 13-15 P5 TO 15 PIN DOOR CONNECTOR Q4 A06 R7 4.7K R8 10K Y B 1 B 2 R 3 4 P3 P1 6 5 4 3 2 1 POWER IN 1 2 3 R4 10K Q3 A56 +5 V +12 V GND GND +5 V Q2 A06 R3 4.7K R6 10K R5 10K 1 2 3 Q1 A56 P2 B BL P4 +5 V R2 10K P4 D2 K3 D1 K2 K1 K3 K3 AMPLIFIER POWER W B 1 2 3 40983801 P5 N N.O. L N.O. K2 L N.O. L ROUTER POWER N K1 B.A. POWER DISPLAY POWER N P6 ATX POWER W G/Y B P2 N P3 1 2 3 P1 N.C. N L N S1 L POWER CB1 10A 40984301 POWER DISTRIBUTION ASSY NGX MINI WIRING DIAGRAM (PAGE 2) Page 31 P7 120 VAC INPUT 22121206 POWER CORD TO CABINET FANS ON CORE COMPUTER GND GND POWER POWER 1 2 3 4 B R B R 2 1 2 1 34039109 CABINET FAN CH 2 CH 1 E1 E2 E3 E4 E5 E6 E7 B/W BR B E1 E2 E3 E4 E5 E6 E7 70 V A2 A1 A1 A2 G 40832123 22180806 - OPTIONAL AUDIO TRANSFORMER KIT BGM IN CH1 TO AUDIO OUTPUT ON CORE COMPUTER CH2 30934231 MAIN IN - STEREO PLUG CH1 CH4 POWER BR STATUS P101 RL COMM CH 2 OUT GND GND CH 1 OUT MUTE THERMAL B/W 1 2 3 4 OVR CRNT EXT OUT CH3 1 2 3 4 5 MIC 2 INPUT J3 SIGNAL SENSE POWER GND SHIELD LEFT GND GND RIGHT MUTE J2 1 2 3 4 5 MIC 1 INPUT TO ROWELINK (GREEN) ON CORE COMPUTER SIGNAL SENSE POWER GND 22215009 W TO AMPLIFIER POWER ON POWER DISTRIBUTION ASSY 40912013 1 2 3 4 5 6 7 8 B 1 2 3 Shld G B W R O/B P102 8 CH 1 IN 7 GND 6 GND BR 5 CH 2 IN 4 THERMAL 3 OVER CURRENT 2 ENABLE W/BR 1 BTL SY NC J7 34104601 INTERFACE J10 +24VDC GND R B 1 2 POWER ROWELINK 61200701 PREAMP 34104701 34104401 P103 1 2 3 +24VDC GND AUX PWR OUT P100 B 1 2 3 W 40991404 AMPLIFIER ASSY 1 2 3 40983901 ICEpower AMPLIFIER LINE NEUTRAL POWER NGX MINI WIRING DIAGRAM – SINGLE AMPLIFIER CONFIGURATION (PAGE 3) Page 32 B AUDIO OUT G 34104501 CH2 SPEAKER BINDING POSTS OPTIONAL DUAL BA INSTALL U.S. 4 7 9 10 20 21 22 24 120V NEU CREDIT PULSE SEL GROUND 120V HOT EARTH OOS ENABLE 22135613 MEI AE2681D7EUS -- OR -22135614 COINCO VL61D47US01 SINGLE BA INSTALL W Y B/Y B/Y B G/Y BL BR 34095702 1 2 3 4 5 6 7 8 9 34022350 B/W BR B B/W G Y BL W U.S. 4 7 9 10 20 21 22 24 4 7 9 10 20 21 22 24 34022350 1 2 3 4 5 6 7 8 9 120V NEU CREDIT PULSE SEL GROUND 120V HOT EARTH OOS ENABLE 1 2 3 4 5 6 7 8 4 7 9 10 20 21 22 24 120V NEU CREDIT PULSE SEL GROUND 120V HOT EARTH OOS ENABLE 22135613 MEI AE2681D7EUS -- OR -22135614 COINCO VL61D47US01 4 7 9 10 20 21 22 24 120V NEU CREDIT PULSE SEL GROUND 120V HOT EARTH OOS ENABLE 22135613 MEI AE2681D7EUS -- OR -22135614 COINCO VL61D47US01 22178602 IMONEX COIN ACCEPTOR BR O R B W G CANADIAN $1, $2 $2 B G $1 W BR O CANADA TO COINS (BLUE) ON CORE COMPUTER GND +12 V COIN 5 COIN 6 LED ON INHIBIT COIN 1 COIN 2 COIN 3 COIN 4 1 2 3 4 5 6 7 8 9 10 NC 1 NC 2 GND 3 OOS 4 +5 V 5 NC 6 CREDIT 7 ESCROW 8 ENABLE 9 DATA 10 B/W R O W B/Y BL Y 34022353 DOOR HARNESS 61113308 CABINET HARNESS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 O B/W 1 O 2 3 4 R 5 B/W 6 W 7 B/W 8 1 2 3 4 5 6 7 8 B/W Y B/Y BL BR R-2 B/W-2 22178601 IMONEX COIN ACCEPTOR COM N.O. QUARTER ONLY U.S. B G/Y W BR 1 2 1 2 BACKLIGHT PANEL 22325401 - DIFFUSER 34105801 - CBA, LED BACKLIGHT R B TO BILLS (WHITE) ON CORE COMPUTER 22185302 CREDIT CARD READER TO POWER DISTRIBUTION ASSY Supplied with Card Reader TO CORE COMPUTER NGX MINI WIRING DIAGRAM (PAGE 4) Page 33 R This page is intentionally left blank. Page 34 Section F Parts Catalog • Front Door/LCD Assembly • Inside Cabinet • Currency Components • Electronic Components • Computer Core • Power Supply • Amplifier Assembly • Accessories Page 35 Front Door/LCD Assembly 1 24 3 13 18 2 12 6 7 8 25 15 26 27 14 5 17 16 19 4 28 20 10 21 11 9 22 20 23 OUTSIDE VIEW Ref. 1 2 3 4 5 6 7 8 9 10 Qty. 1 1 2 Ref. 14 15 16 17 18 19 20 21 Part # 61199702 34103701 22323002 00710206 70093403 34038702 22164202 21121225 34103702 40992401 Description Door Assembly Top Front Door Catch Female Hinge Foam Rubber Gasket Cable Clamp Serial Cable VGA Cable Power Cord Bottom Front Door Catch Coin Box Retainer Qty. Part # 1 61200109 2 2 4 2 1 1 1 2 34103805 40990706 22323503 61200217 40990612 22327701 61200007 34104907 Description Lighting Assembly (includes all parts below) Horizontal Bezel Plate Vertical Bezel Plate Corner Bezel Plate Vertical Bracket Top Bracket Harness Cover Diffuser Diffuser Clamp Bracket 3 1 1 1 1 1 INSIDE VIEW Ref. 11 12 13 13a 13b 13c 13d 13e Qty. 1 1 1 1 1 1 1 1 1 Part # 40990301 61205001 61205050 61205051 61205053 61205054 61205055 61205052 22323901 Description Coin Container Flatscreen LCD Touchscreen Touchscreen Controller A-to-D Board LCD Panel Monitor Gasket Monitor Power Supply Connector Block-Out Plate Ref. Qty. Part # Description 22 1 40990614 Bottom Bracket 23 24 2 34105001 Diffuser Clamp Bracket 1 22326302 LED Strip 1 HW8889-01 Self-Adhesive Cable Clamp Shown for reference, not included in light assembly: 25 1 41010701 LED Control CBA 26 1 34102201 Light Interconnect CBA 27 1 22327801 LED Mounting Bracket 28 3 70093402 Cable Clamp Page 36 Inside Cabinet INSIDE CABINET Ref. 1 2 3 4 5 6 7 8 9 10a 10b 11 12 13 14 15 16 Qty. 2 3 2 6 1 2 1 2 1 1 2 1 1 1 1 1 1 Part # 22323001 34103501 22324201 25156904 70091702 22323101 21256201 34100601 61199502 34024501 80443006 70163215 61197004 22321601 22321701 34039109 21895503 Description Male Hinge Cord Hole Cover 8-32 Finger Nut Shoulder Washer Solder Lug Cabinet Latch Tension Spring Lock Actuator Cabinet Lock Bolt #8-32 x 3/8 Hex WHMS Cylinder Lock Computer Core Assembly Right Mounting Bracket Left Mounting Bracket Fan with Connector Fan Finger Guard Ref. 17 18 19 20 21 22 23 24 25 26 27 Page 37 Qty. Part # Description 1 40991404 500-Watt Amplifier Assy. 1 22320601 Reset Bracket 1 21581801 Push Button Switch 1 40984301 Power Supply Assembly 1 70093402 Cable Clamp 2 70093403 Cable Clamp 1 34103603 Short Baffle 2 70093401 Cable Clamp 2 70120926 Washer 1 87844400 #10-32 Keps Hex Nut 1 89974808 #10-32 x ½ Carriage Bolt Components not shown in assembly above: 1 61113308 Main Harness 1 21121240 Power Cord 1 34053003 Air Filter 1 34053004 Air Filter Currency Components 12 13 11 9 or 10 14 8 7 3, 4, 5, or 6 2 15 1 Ref Qty Part # Description 1 1 22178601 Coin Acceptor 2 1 22151005 Coin Inlet Decal 3 1 40990001 Bill/Credit Graphic Panel 4 1 40990101 Bill/Credit/Coin Graphic Panel 5 1 40990201 2 Bill/Credit/Coin Graphic Panel 6 1 40990401 2 Bill/Credit Graphic Panel 7 1 40991101 Lighting Panel Backer 8a 1 22325404 Light Panel (AMI) 8b 1 34105804 CBA Backlight LED Ref. Qty. Part # 9 1-2 22135614 10 1-2 22135613 11 1 34100002 12 1 34105101 13 1 61199203 14 1 61199204 15a 1 22185350 15b 1 PM0725-01 15c 2 28277903 Page 38 Description Coinco Bill Acceptor MEI Bill Acceptor Dual Bill Circuit Board Assy. Coin Mech Plate Inner Door Panel Outer Door Panel Credit Card Reader Credit Card Reader Label #M3x16 PPHMS Electronic Components Computer Core Assembly 61197004 Ref. Qty. Part # Description 1 1 22137302 Guide – Card 2 1 34052405 CBA – Power On/Reset 3 1 34101103 Cover – Small 4 1 40983503 Cover - Top 5 1 34039110 Fan – Chassis Cooling w/Tach 6 1 34101201 Bracket – Hard Drive Mounting 7 1 91197103 Housing – Core Computer 9 2 87842300 Nut - #6-32 Keps Hex 10 1 40955205 Power Supply 11 14 80352304 #6-32x1/4 PPHMS 12 1 40924214 Single Bd Computer Assy Ref. 13 14 15 16 Qty. 1 1 1 1 Ref Ref 1 1 Page 39 Part # Description 61196903 CBA – I/O Interface 22328802 Bracket – PCI Modem Blockout 22167704 Label – Computer Connections 22167705 Label – Jukebox Connections Components not shown above 1 22132269 Harness Assy – Com I/O 1 22132270 Harness Assy – Power 1 22132252 Cable – SATA Data 22219001 22219002 Hard Drive – 320GB System, Hard Drive – 320GB Canada Electronic Components Power Supply Assembly 40984301 8 1 2 7 3 4 5 6 Ref. Qty. Part # Description 1 1 40984401 Power Supply Cover 2 1 30785706 Rocker Switch 3 1 40983801 Power Control CBA 4 2 71300091 PC Support Standoff Ref. Qty. Part # 5 1 40984201 6 2 87842300 7 1 22118705 8 3 21375905 Page 40 Description Low Voltage Power Control CBA #6-32 Keps Hex Nut Power Inlet Convenience Outlet Electronic Components Amplifier Assembly 40991404 1 2 3 7 4 5 6 Ref. Qty. Part # 1 1 61200305 2 1 61200706 3 1 40983901 4 1 61200401 5 1 34104401 6 2 34104201 Description Amplifier Cover 4-Channel Preamplifier CBA 500-Watt Amplifier Amplifier Base Amp Power Harness Dual Binding Post Ref. Qty. Part # Description 7 2 89281606 #4-24 x 3/8 Pan Head Screw Components not shown above: 1 34104601 Audio In Harness 1 34104501 Audio Out Harness 1 34104701 Preamplifier Power Harness Page 41 Accessories Part Number 22118916 21958306 40846302 34037905 21121216 70004-1A 62009-A-LF 34024502 22324601 Description Handy Pack (contains the following): IR Transmitter IR Receiver IR Receiver Cable Power Cord 2-Channel Remote Control Remote Control Cable Lock Bolt (Ace Lock) Cable Retainer Bracket 22200862 89986124 ST-11327 Small Parts Kit (contains the following): Screw, Lag 1/4 x 1-1/2” Hex Head #8 x 1 1/2” Phillips Pan Head Screws for 2-Channel Remote (4) (2) Optional Kits 26704801 22180806 22178504 26682503 26681501 02468 26679501 26679502 26679701 26679702 26679703 26695501 26695402 Kit – Router, Wireless Kit – Output Transformers Kit – Modem, Internal PCI-Ex Kit – Money Meter Kit – Special Event Switch Kit – Wireless, RF Remote Control Kit – Paging with Cable Kit – Paging w/o Cable Kit – 2nd Bill Acceptor (parts only - Bill Acceptor not included) Kit – 2nd Bill Acceptor (includes CoinCo Bill Acceptor) Kit – 2nd Bill Acceptor (includes MEI Bill Acceptor) Kit – NGX Video Kit – Video Marquee ,NGX Mini Page 42 AMI Entertainment Network, LLC – 4147 Eastern Avenue SE – Grand Rapids, Michigan 49508
© Copyright 2024 Paperzz
