Type 400 Controller General Handbook
SIEMENS TRAFFIC CONTROLS LIMITED
Sopers Lane
POOLE Dorset.
BH17 7ER
PRODUCT: T400 CONTROLLERS
T400 CONTROLLER
GENERAL HANDBOOK
Prepared : P. COX
Approved : J.P. BURGESS
Function : Software Engineer
Function : Engineering Manager
Signature :
ISSUE:
Signature :
CHANGE REF.:
1
DATE:
APPROVED BY:
13/04/89
2
83/15278
18/07/89
3
83/15611
19/04/90
4
83/15950
15/02/91
5
83/16025
22/03/91
6
83/16703
24/09/92
7
83/17049
10/02/92
8
ANL00272
12/11/96
9
ANL00476
4/7/97
10
Jan 99
В© Siemens plc. 1996 All rights reserved.
The information contained herein is the property of Siemens plc. and is supplied
without liability for errors or omissions. No part may be reproduced or used except
as authorized by contract or other written permission. The copyright and the
foregoing restriction on reproduction and use extend to all media in which the
information may be embodied.
667/HB/20200/000
Page i
Issue 10
Type 400 Controller General Handbook
SAFETY WARNING
In the interests of health and safety, when using or servicing this equipment the
following instructions must be noted and adhered to:
(i)
Only skilled or instructed personnel with relevant technical knowledge and
experience, who are also familiar with the safety procedures required when
dealing with modern electrical/electronic equipment are to be allowed to use
and/or work on the equipment. All work shall be performed in accordance with
the Electricity at Work Regulations 1989.
(ii)
Such personnel must take heed of all relevant notes, cautions and warnings in
this handbook, the Maintenance Handbook (667/HA/20200/000) and any other
document or handbook associated with the equipment including, but not
restricted to, the following:
(iii)
(a)
The equipment must be correctly connected to the specified incoming
power supply.
(b)
The equipment must be disconnected/isolated from the incoming power
supply before removing protective covers or working on any part from
which protective covers have been removed.
(c)
This equipment contains a Lithium battery which must be disposed of in
a safe manner. If in doubt of the correct procedure refer to the Siemens
instructions.
In the event of any person working elsewhere on the junction, the mains
supply to the controller should be switched off and the master switch locked in
the OFF position using the master switch lock facility (667/1/21386/000).
Warning:- Removal of the electricity board fuse or switching off the controller
switch or manual panel signals ON/OFF switch does not guarantee
isolation of the equipment.
667/HB/20200/000
Page ii
Issue 10
Type 400 Controller General Handbook
ISSUE STATE
Note: Source of documents is shown under Type as below.
1=Paper, 2=VAX, 3=Microfilm, 4=CALTEXT Disk, 5=DECmate Disk,
6=Paper Insert, 7=Disk, 8=AMW , 9=SUN, 10=Other - PC Disk
The document comprises the following components :
Pages
Current
Issue
Type
Part ID
i to ix
1-1 to 1-17
2-1 to 2-19
3-1 to 3-17
4-1 to 4-15
5-1 to 5-6
6-1 to 6-32
7-1 to 7-16
8-1
A-1
B-1
C-1 to 3
D-1 to 7
E-1
10
10
10
10
10
10
10
10
10
10
10
10
10
10
8
8
8
8
8
8
8
8
8
8
8
8
8
8
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
667/HB/20200/000
Information in this document is subject to change without notice. Companies, names
and data used in examples herein are fictitious unless otherwise noted. No part of
this document may be reproduced transmitted in any form or by any means,
electronic or mechanical, for any purpose, without the express written permission of
Siemens plc.
667/HB/20200/000
Page iii
Issue 10
Type 400 Controller General Handbook
CONTENTS
1. INTRODUCTION .................................................................................................1-1
1.1 GENERAL ......................................................................................................1-1
1.1.1 FACILITIES ............................................................................................1-3
1.1.2 SIGNALS................................................................................................1-3
1.2 GLOSSARY OF TERMS ................................................................................1-4
1.2.1 Associated Documentation ....................................................................1-5
1.2.2 Kindred Documents................................................................................1-8
1.3 BASIC SYSTEM OVERVIEW .........................................................................1-8
1.3.1 HARDWARE OVERVIEW ......................................................................1-8
1.3.2 Customisation ........................................................................................1-9
1.4 CONSTRUCTION.........................................................................................1-10
1.4.1 Small Outercase...................................................................................1-10
1.4.2 Large Outercase ..................................................................................1-10
1.5 SAFETY........................................................................................................1-12
1.5.1 Controller System Checks....................................................................1-12
1.5.2 Power up Checks .................................................................................1-13
1.5.3 Green Correspondence Tests..............................................................1-14
1.5.4 System Background Test .....................................................................1-15
1.5.5 Operation of the Safety System ...........................................................1-16
1.5.6 Red Lamp Monitoring...........................................................................1-17
2. SPECIFICATION .................................................................................................2-1
2.1 MAINS SUPPLY .............................................................................................2-1
2.1.1 Electrical Noise ......................................................................................2-2
2.2 DETERMINATION OF LOADING, SELECTION OF DIMMING
TRANSFORMER & LAMP FUSE .........................................................................2-3
2.2.1 Controller Load ......................................................................................2-3
2.2.2 Lamp Drive Capability............................................................................2-3
2.2.3 Selection of Dimming Transformer.........................................................2-4
2.2.4 Calculating The Lamp Supply Fuse Required .......................................2-5
2.2.5 Calculation Of An Intersection’s Power Requirements For Running Costs
Estimate ..........................................................................................................2-7
2.2.6 Regulated Logic Supplies ....................................................................2-10
2.2.7 Regulated Interface & Detector Supplies.............................................2-10
2.2.8 Audible Supplies ..................................................................................2-11
2.3 FUSE RATINGS ...........................................................................................2-12
2.4 PHASES .......................................................................................................2-13
2.5 STAGES .......................................................................................................2-13
2.6 TIMINGS.......................................................................................................2-13
2.7 MASTER TIME CLOCK & CABLELESS LINK FACILITY SUMMARY ..........2-17
2.8 MODES OF OPERATION ............................................................................2-17
2.9 OUTERCASE ...............................................................................................2-17
2.10 ENVIRONMENTAL.....................................................................................2-18
2.10.1 Temperature.......................................................................................2-18
2.10.2 Atmospheric .......................................................................................2-18
2.10.3 Humidity .............................................................................................2-18
2.11 HANDSET INTERFACE (RS232 PORT) ....................................................2-18
667/HB/20200/000
Page iv
Issue 10
Type 400 Controller General Handbook
3. TRAFFIC FACILITIES.........................................................................................3-1
3.1 STAGES .........................................................................................................3-1
3.1.1 Stage Facilities.......................................................................................3-1
3.1.2 Allocation Of Phases..............................................................................3-1
3.1.3 Stage Active ...........................................................................................3-1
3.1.4 Stage Terminating..................................................................................3-1
3.1.5 Inter Stage Period ..................................................................................3-1
3.1.6 Stage Movement Restrictions ................................................................3-1
3.1.7 Prevent Stages/Phases..........................................................................3-2
3.2 PHASES .........................................................................................................3-2
3.2.1 Types Of Phases....................................................................................3-2
3.2.2 Conflicting Phases .................................................................................3-2
3.2.3 Opposing Phases...................................................................................3-2
3.2.4 Phase Delays .........................................................................................3-3
3.2.5 Timing Periods .......................................................................................3-3
3.2.6 Limiting Values.......................................................................................3-3
3.2.7 Conditions Of Appearance For Phases..................................................3-3
3.2.8 Fixed Phase ...........................................................................................3-3
3.2.9 Non Fixed Phases..................................................................................3-4
3.2.10 Conditions Of Termination For Phases................................................3-4
3.2.11 Early Termination Of Phases ...............................................................3-4
3.3 DEMANDS AND EXTENSIONS .....................................................................3-4
3.3.1 Types Of Demands ................................................................................3-4
3.3.2 Origins Of Demands And Extensions.....................................................3-4
3.3.3 Repeat Pulses........................................................................................3-4
3.3.4 SDE/SA ..................................................................................................3-5
3.3.5 Handset..................................................................................................3-5
3.3.6 Operation Of Demands And Extensions During Certain Modes ............3-5
3.4 HIGH SPEED VEHICLE DETECTION............................................................3-7
3.4.1 Speed Discrimination Equipment (SDE) ................................................3-7
3.4.2 Speed Assessment (SA) ........................................................................3-7
3.4.3 Assessors Available ...............................................................................3-7
3.4.4 Extra Clearance Periods ........................................................................3-7
3.4.5 SDE/SA on Green Arrows ......................................................................3-8
3.4.6 Other Manufacturers Loops ...................................................................3-8
3.5 MODES ..........................................................................................................3-9
3.5.1 Start-Up Mode........................................................................................3-9
3.5.2 Part-Time Mode .....................................................................................3-9
3.5.3 Urban Traffic Control..............................................................................3-9
3.5.4 Priority Mode ..........................................................................................3-9
3.5.5 Hurry Call Mode .....................................................................................3-9
3.5.6 Selected Manual Control........................................................................3-9
3.5.7 Selected Fixed Time or V.A. or CLF. .....................................................3-9
3.5.8 Normal Mode........................................................................................3-10
3.5.9 Cableless Link Facility (CLF) Mode .....................................................3-10
3.5.10 Vehicle Actuated Mode ......................................................................3-10
3.5.11 Fixed Time Mode ...............................................................................3-10
3.6 MASTER TIME CLOCK................................................................................3-10
3.7 LINKING .......................................................................................................3-10
3.8 ALTERNATIVE SIGNAL SEQUENCES........................................................3-11
667/HB/20200/000
Page v
Issue 10
Type 400 Controller General Handbook
3.9 INPUTS & OUTPUTS...................................................................................3-12
3.10 MANUAL PANEL FACILITIES....................................................................3-14
3.10.1 Full Intersection Controller Manual Selection Panel ..........................3-14
3.10.2 Police Manual Panel (Hong Kong) .....................................................3-14
3.10.3 Internal Manual Panel (Hong Kong)...................................................3-15
3.10.4 Basic Manual Panel ...........................................................................3-15
3.10.5 Optional Manual Panel Facilities .......................................................3-15
3.11 SIGNAL AND DETECTOR ISOLATING SWITCHES .................................3-15
3.12 T400 FAILURE FLASHER FACILITY (EXPORT ONLY) ............................3-16
3.13 HANDSET ..................................................................................................3-16
3.14 SPECIFICATION SHEETS (667/DJ/15900/000) ........................................3-17
4. PELICAN/PEDESTRIAN CONTROLLER ...........................................................4-1
4.1 GENERAL ......................................................................................................4-1
4.1.1 Fixed Vehicle Period mode ....................................................................4-1
4.1.2 Pelican VA mode....................................................................................4-1
4.2 PELICAN/PEDESTRIAN TIMINGS.................................................................4-2
4.2.1 Puffin Sequence Timings .......................................................................4-2
4.3 MANUAL PANEL FACILITIES........................................................................4-3
4.3.1 Select VA/FVP .......................................................................................4-3
4.3.2 Continuous Ped. Demand ......................................................................4-3
4.3.3 Continuous Vehicle Extension ...............................................................4-4
4.3.4 DFM Reset .............................................................................................4-4
4.3.5 Auxiliary LEDs (AUX1, AUX2, AUX3) and Switches (SW1, SW2, SW3)4-4
4.4 HANDSET ......................................................................................................4-5
4.4.1 Timings...................................................................................................4-5
4.4.2 Speed Discrimination (SDE/SA).............................................................4-5
4.4.3 Manual Facilities ....................................................................................4-5
4.5 I/O LINE ALLOCATION ..................................................................................4-6
4.6 WAIT INDICATORS .......................................................................................4-7
4.7 AUDIO CONTROL AND MONITOR ...............................................................4-7
4.8 GREEN CONFLICT FAULT ACTION .............................................................4-7
4.9 RED LAMP MONITORING .............................................................................4-7
4.10 DESCRIPTION OF I/O LINE FUNCTIONS ..................................................4-8
4.10.1 UTC Facilities.......................................................................................4-8
4.10.2 Local Link Facilities............................................................................4-11
4.10.3 Call/Cancel Function..........................................................................4-13
4.10.4 Puffin I/O Facilities.............................................................................4-13
4.11 TIMESWITCH FACILITIES.........................................................................4-14
4.12 CLF FACILITIES.........................................................................................4-15
4.13 CROSS-INHIBIT LINKING..........................................................................4-15
5. HANDSET COMMANDS .....................................................................................5-1
6. GENERAL ARRANGEMENT OF T400 HARDWARE.........................................6-1
6.1 SMALL OUTERCASE.....................................................................................6-1
6.1.1 Master Switch Panel ..............................................................................6-1
6.1.2 Controller Panel .....................................................................................6-1
6.1.3 PCB Module ...........................................................................................6-1
6.1.4 Manual Panel & Cabinet Alarm ..............................................................6-1
667/HB/20200/000
Page vi
Issue 10
Type 400 Controller General Handbook
6.1.5 Uncommitted Space ...............................................................................6-2
6.2 LARGE OUTERCASE ....................................................................................6-4
6.2.1 Master Switch Panel ..............................................................................6-4
6.2.2 Distribution Panel...................................................................................6-4
6.2.3 PCB Module ...........................................................................................6-4
6.2.4 Manual Panel & Cabinet Alarm ..............................................................6-4
6.2.5 Uncommitted Space ...............................................................................6-5
6.3 EXPANDED DESCRIPTIONS OF T400 HARDWARE & OTHER EQUIPMENT6-10
6.3.1 O.T.Us/O.M.Us.....................................................................................6-10
6.3.2 TELECOMMAND 8 INTEGRAL SCOOT OTU (EXPORT ONLY).........6-10
6.3.3 OTU Functions.....................................................................................6-10
6.3.4 Detector Racks and Detectors .............................................................6-11
6.3.5 Manual Panel & Cabinet Alarm ............................................................6-12
6.3.6 PCB Module .........................................................................................6-21
6.3.7 Power System ......................................................................................6-22
6.3.8 LED Indicators......................................................................................6-23
6.3.9 Handsets ..............................................................................................6-23
6.3.10 300mA Controller Residual Current Detector.....................................6-23
6.4 EXPANDED DESCRIPTIONS OF T400 PCBs.............................................6-24
6.4.1 Main Processor P.C.B (667/1/20221/000) ...........................................6-24
6.4.2 4 Phase Driver PCB (667/1/20223/000)...............................................6-26
6.4.3 2 Phase Driver PCB (667/1/20225/000)...............................................6-26
6.4.4 Manual Panel P.C.B (667/1/20227/000) ..............................................6-27
6.4.5 Expansion I/O PCB (667/1/20229/000) ................................................6-28
6.4.6 Expansion I/O PCB (667/1/20229/001) ................................................6-29
6.4.7 SDE/SA P.C.B (667/1/20231/000) .......................................................6-30
6.4.8 Ancillary Processor P.C.B (667/1/21611/000)......................................6-31
7. GUIDE TO T400 SPECIFICATION FORMS........................................................7-1
7.1 GENERAL ......................................................................................................7-1
7.2 LIST OF FORMS ............................................................................................7-2
7.3 FILLING OUT THE FORMS ...........................................................................7-3
8. T400 MOD STATE CONTROL AND CONFIGURATION....................................8-1
APPENDIX A - SPECIFICATION SHEETS ................................................................ 1
APPENDIX B - MOD STATE CONTROL AND CONFIGURATION ....................... B-1
APPENDIX C - 50-0-50 VOLT CONTROLLER...................................................... C-1
C.1 50-0-50 VOLT CONTROLLER...................................................................... C-1
C.1.1 Signal load limitations........................................................................... C-1
C.1.2 Miniature Circuit Breaker (MCB)........................................................... C-2
C.1.3 Street Equipment .................................................................................. C-2
C.1.4 Dual Solar Cell ..................................................................................... C-2
C.2 GAS PLINTH................................................................................................. C-3
APPENDIX D - ADDITIONAL REQUIREMENTS FOR TUEN MUN....................... D-1
D.1 LAMP DRIVE CAPABILITY........................................................................... D-1
D.1.1 Lamp Load Per Aspect (Watts) ............................................................ D-1
D.1.2 Dimming Transformer ........................................................................... D-1
667/HB/20200/000
Page vii
Issue 10
Type 400 Controller General Handbook
D.1.3 Calculation Of An Intersections Power Requirements.......................... D-2
D.1.4 Calculating The Lamp Supply Fuse Required ...................................... D-3
D.2 HANDSET RANGE LIMITS, DEFAULT VALUES ......................................... D-4
D.3 INPUTS AND OUTPUTS .............................................................................. D-5
D.4 ADDITIONAL INFORMATION FOR TUEN MUN SPECIAL SPEC. SHEETSD-6
APPENDIX E - T400 CONTROLLER DRAWINGS ................................................ E-1
LIST OF ILLUSTRATIONS
FIGURE 2.2 - THEORETICAL JUNCTION..............................................................2-9
FIGURE 6.1 - T400 IN A SMALL OUTERCASE......................................................6-3
FIGURE 6.2(A) - T400 LARGE OUTERCASE FRONT VIEW (TYPICAL)...............6-6
FIGURE 6.2(B) - T400 LARGE OUTERCASE REAR VIEW (TYPICAL) .................6-7
FIGURE 6.2(C) - T400 LARGE OUTERCASE FRONT VIEW (HONG KONG) .......6-8
FIGURE 6.2(D) - T400 LARGE OUTERCASE REAR VIEW (HONG KONG)..........6-9
FIGURE 6.3.5.1 - INTERSECTION CONTROLLER MANUAL SELECTION PANEL6-14
FIGURE 6.3.5.2 - POLICE MANUAL PANEL LAYOUT (HONG KONG) ...............6-16
FIGURE 6.3.5.3 - INTERNAL MANUAL PANEL LAYOUT (HONG KONG)...........6-18
FIGURE 6.3.5.4 - BASIC MANUAL PANEL LAYOUT ...........................................6-19
FIGURE 6.3.5.5 - PELICAN CONTROLLER MANUAL PANEL.............................6-20
FIGURE 6.3.6 - ARRANGEMENT OF PCB’S WITHIN MODULE..........................6-21
FIGURE 6.4.1 - MAIN PROCESSOR PCB............................................................6-25
FIGURE 6.4.8 - ANCILLARY PROCESSOR PCB .................................................6-32
667/HB/20200/000
Page viii
Issue 10
Type 400 Controller General Handbook
PREFACE
It is intended that this preface should guide the reader as to the use of this
handbook, thus assisting the reader in selecting the best section to read in order to
obtain the information required.
Section 1
Introduction:- This will in a brief manner give a basic understanding of
the controller construction and capabilities.
Section 2
Specification:- This gives values and ranges for the following items:
Weight, Size, Currents, Voltages, Lamp loads, Phases, Stages etc.
Section 3
Traffic Facilities:- This contains a list of the controllers functions and
facilities as a brief overview of its capabilities. Each heading in the list
is extracted from Facilities Manual Handbook 667/EB/20200/000.
Where further details on each subject can be found. Some headings
are followed by brief descriptions to aid understanding.
Section 4
Pelican/Pedestrian Facilities:- This contains a brief description of each
of the 0125 Pelican and 0145 Pedestrian, and Puffin controller facilities.
Section 5
Simplified Handset Commands:- This contains a simplified set of
handset commands to give an example of the accessibility of the data
stored in the T400. Handbook 667/HH/20200/000 contains full details of
T400 handset commands.
Section 6
Technical Descriptions:- This contains descriptions of the units of
hardware which together make up a T400 Controller.
The descriptions are written such that they detail the functions of each
unit of hardware. The section starts at a high level with an overview of
the controller and then step by step breaks it down to individual unit
details.
Section 7
Guide to T400 Specification forms:- this section is provided to help the
user to fill out the Specification sheets contained in Appendix A.
Section 8
PCB issues for use with T400 Firmware: - this section simply refers to
the document entitled “Use of T400 Firmware and Configuration” which
is contained in Appendix B.
Appendix A Specification Sheets:- This is a copy of document number
667/DJ/15900/000 and is used to specify the facilities required in the
controller.
Appendix B Copy of 667/SU/20200/000 - Mod state control and configuration.
Appendix C 50-0-50 Volt Controller
Appendix D Tuen Mun Special Requirements
Appendix E T400 Controller Drawings
667/HB/20200/000
Page ix
Issue 10
Type 400 Controller General Handbook
1. INTRODUCTION
1.1 GENERAL
The Type 400 controller is based on the 80188 microprocessor. This is a 16
bit device compatible with but having enhancements over the 8088 processor
used in the T200 controller.
The software is written in a powerful high level language. This has allowed
the implementation of the T400 Controller’s extensive facilities. The
Controller offers up to 16 stages and 16 phases controlled using solid state
switching.
The controller is capable of producing all the required facilities specified in
U.K. Department of Transport specification MCE 0141 (Microprocessor
Based Traffic Signal Controller for Isolated Link and Urban Traffic Control
Installations), MCE 0125 (Pedestrian Operated Equipment) & MCE 0145
(Pedestrian Operated Equipment other than Pelican controllers) plus a
number of optional facilities. (See Section 2 traffic facilities).
Specification MCE 0141 is based on the following specifications and
incorporates their most commonly used features.
MCE 0105
-
Fixed Time Traffic Signal Controller (Solid State) for use in
Area Traffic Control Systems.
MCE 0106
-
Vehicle Actuated Signal Controllers (Solid State) for use in
Area Traffic Control.
MCE 0124
-
Cableless Linking
Controllers.
MCE 0126
-
Traffic Signal Controller for Isolated and Linked Vehicle
Actuated Installations.
TCD 316
-
Area Traffic Signal Controller Modifications Specifications.
Unit
for
use
with
Traffic
Signal
Thus, controllers supplied to specification MCE 0141 can be characterised to
allow them to operate in existing Urban Traffic Control Schemes employing
MCE 0105, MCE 0106 or TCD 316 control philosophies.
The controller appears in two styles:(a)
SMALL T400S
The small T400 controller consists of a 2 phase pelican or a 4 real phase
controller with a minimal set of I/O and is intended to perform at small
intersections or where a pelican is required. This controller can be expanded
up to 8 Phases and can accommodate Detectors, OTU, OMU and LMU. The
667/HB/20200/000
Page 1-1
Issue 10
Type 400 Controller General Handbook
small outercase is ground mounted but is of reduced size and has an access
door at the front only.
Expansion may be achieved by adding combinations of the following
equipment:Additional Phase Boards
2 or 4 phase board plus additional conflict monitoring circuitry - giving up to 8
real phase capability.
Input/Outputs
May be expanded to a maximum of 96 input/outputs provided as:64 Inputs (50 buffered & 14 unbuffered)
32 Outputs(all buffered).
Detectors
These can be either Siemens, Microsense, Sarasota self tune units or other
external units (micro-wave, infra-red etc).
Ancillary Equipment
OTU - Outstation Transmission Unit.
OMU/OMCU - Outstation Monitoring (& Control) Unit.
LMU - Lamp Monitoring Unit.
(b)
LARGE T400L
The large T400 is housed in a ground mounted case of standard size (large
outercase) with access doors at the front and rear.
There is room to expand the basic system to cater for practically any
intersection.
Additional Phase Boards
2 or 4 phase boards plus additional conflict monitoring circuitry - giving up to
16 real phase capability.
Input/Outputs
May be expanded to a maximum of 96 input/outputs provided as:64 Inputs (50 buffered & 14 unbuffered)
32 Outputs (all buffered).
Detectors
These can be either Siemens, Microsense, Sarasota self tune units or other
external units (micro-wave, infra-red etc).
Ancillary Equipment
OTU - Outstation Transmission Unit.
OMU/OMCU - Outstation Monitoring (& Control) Unit.
667/HB/20200/000
Page 1-2
Issue 10
Type 400 Controller General Handbook
Bus Priority Interrogator.
LMU - Lamp Monitoring Unit.
1.1.1 FACILITIES
Operational:Vehicle actuated
-
SDE/SA is an addition to V.A.
-
Fixed Time
-
Computer control in U.T.C system
-
C.L.F Timetable selected plans
-
Master time clock
This is a real time clock used for the introduction/deletion
of selected events or C.L.F plans.
-
Hurry call
-
Manual
-
Priority
-
Part time (Both OFF/ON or Normal operation/Flashing)
-
Parallel stage streaming
1.1.2 SIGNALS
-
Normal traffic phases
-
Pedestrian phases (with WAIT indicators)
-
Pelican vehicle phases
-
Pelican pedestrian phases
(with WAIT indicators & audible signal)
-
Green arrow (filter and indicative)
-
Switched signs
-
LRT phase
(it has the signal sequence of a pedestrian phase with
flashing green instead of blackout.)
667/HB/20200/000
Page 1-3
Issue 10
Type 400 Controller General Handbook
1.2 GLOSSARY OF TERMS
AC
ACT
CLF
CLU
CMOS
CPU
CRC
DC
DFM
ELCB
EPROM
GP
I/O
LCD
LED
LSTTL
MC
OMCU
OMU
OTU
PCB
PPM
PROM
RAM
RCD
RMS
ROW
RTC
SA
SCOOT
SDE
ST
SWG
TTL
UTC
VA
Alternating Current
Advanced CMOS compatible with TTL
Cableless Linking Facility
Cableless Linking Unit
Complementary Metal Oxide Silicon
Central Processing Unit
Cyclic Redundancy Code
Direct Current
Detector Fault Monitor
Earth Leakage Circuit Breaker
Erasable Programmable Read Only Memory
General Purpose
Input/Output
Liquid Crystal Display
Light Emitting Diode
Low Power Schottky Transistor Transistor Logic
Manual Control
Outstation Monitor and Control Unit
Outstation Monitor Unit
Outstation Transmission Unit
Printed Circuit Board
Parts Per Million
Programmable Read Only Memory
Random Access Memory
Residual Current Device
Root Mean Square
Right Of Way
Real Time Clock
Speed Assessment
Split Cycle Offset Optimisation Technique
Speed Discrimination Equipment
Self Tuning
Standard Wire Gauge
Transistor Transistor Logic
Urban Transport Control
Vehicle Actuated
667/HB/20200/000
Page 1-4
Issue 10
Type 400 Controller General Handbook
1.2.1 Associated Documentation
667/EB/20200/000 - T400 CONTROLLER FACILITIES MANUAL
This handbook details the uses of, and how to specify (using customer spec.
sheets) the requirements for the following facilities:
Stages
Phases
Demands and Extensions
Call/Cancel
High Speed Vehicle Detection
All Red Displays
Phase Delays
Modes:Start Up
Part Time
Urban Traffic Control (UTC)
Emergency Vehicle
Priority
Hurry Call
Selected Manual Stage Control
Manual Stage Control
Manual Step On
Selected Fixed Time/Vehicle Actuated
Cableless Linking Facility (CLF)
Vehicle Actuated
Fixed Time
Stage Movement Restrictions
The Master Time Clock System
Event Time Table
Linking
Alternative Signal Sequences and Flashing Signals
Inputs and Outputs
Manual Panel
Equipment Options
At the end of this handbook are worked examples of intersections with
customer specification sheets completed.
667/HB/20200/000
Page 1-5
Issue 10
Type 400 Controller General Handbook
667/HH/20200/000 - TYPE 400 CONTROLLER HANDSET COMMAND LIST
The handbook details the following:Data entry, display and command formats.
The controller data which can be accessed via the handset and the handset
commands necessary to access the items.
Operational aspects of the intelligent terminal software, which allows an
EPSON HX20 to act as an intelligent terminal for use with a T400.
Operational aspects of the software, which allows a Portable IBM-compatible
computer to act as an intelligent terminal for use with a T400.
667/HH/15900/010 - TUEN MUN HANDSET SUPPLEMENT
This supplement to the handset command handbook 667/HH/20200/000
details the operational facilities of the TRAFFIC CONTROLLER TERMINALS,
supplied on the TUEN MUN - YUEN LONG LRT/TRAFFIC CONTROL
contract.
667/HD/15900/000 - INTERSECTION CONFIGURATOR 3 USERS H/BOOK
(Only available to owners of the configurator)
This handbook details the following:(a)
The hardware requirements for a configuring system (the configurator is
Siemens software running on an IBM PC compatible computer).
(b)
How to use the configuring system to enter data from the completed
customer specification sheets into the computer and produce the
programmed EPROMs required to configure the T400 controller. This
includes the writing of special conditioning and details on error
messages which may be produced during the processing of data
entered.
667/HB/20200/000
Page 1-6
Issue 10
Type 400 Controller General Handbook
667/HE/20200/000 - T400 CONTROLLER INSTALLATION AND
COMMISSIONING MANUAL
This handbook details the requirements for installation and commissioning a
T400 controller.
667/HA/20200/000 - MAINTENANCE H/BOOK FOR T400 CONTROLLERS
This handbook details the following:Safety procedures when working on the T400 traffic controller and its
ancillary equipment.
The use of the handset/terminal for maintenance purposes.
Routine maintenance/inspection procedures.
Fault finding procedures.
Procedures for replacing pcbs.
Clarification of specific controller functions.
PCB histories and retrospective modifications since initial design.
The last section of the handbook contains a basic overview of the controller
hardware at module level with a block diagram representation of the
hardware.
667/KM/20200/000 - SPARES ITEMS LISTS
(WITH MANUFACTURING PART NUMBERS)
This contains items lists for the hardware assemblies which together make up
the traffic controller. These hardware assemblies may be used as spares. If
any components not listed in this document are used then the controller
approval is null and void.
667/HB/26900/000 - GENERAL H/BOOK FOR T400 CONTROLLERS IN
USER OUTERCASES
This handbook provides basic details of the T400 mounted in a U.K. user
outercases as specified by the Traffic Signals User Group (TSUG).
667/HB/20200/000
Page 1-7
Issue 10
Type 400 Controller General Handbook
1.2.2 Kindred Documents
667/DJ/15900/000 - CUSTOMER SPECIFICATION SHEETS
This is a set of blank customer specification sheets.
Note - A set of these are included in this book as Appendix A.
1.3 BASIC SYSTEM OVERVIEW
Control
Microprocessor
Program Storage
Program Data
Program Variables
Logic
-
Intel 80188 family
Powerful chip set
High level language (PLM)
PROM (27C010)
PROM (27256 & 27512)
(Intersection data)
- Battery backed static RAM
(16k x 8).
- CMOS
Lamp Switching
Triac
- Opto isolated, Zero crossing.
- No load dimming changeover
- Signals on dim at start up to
reduce surge currents
Conflict System
PROM Data
- Self testing
Physical Hardware
Logic:Peripheral:-
Double Extended Euro Card
Single Extended Euro Card
1.3.1 HARDWARE OVERVIEW
1.3.1.1 Main Processor Board
The operations of the T400 are controlled by the Main Processor Board.
This board contains a microprocessor based on the Intel 80188
microprocessor. It also contains a Real Time Clock, an RS232C interface for
communications with a handset, the Configuration, Conflict and Firmware
Proms, I/O for interfacing with the Phase Driver Boards, Manual Panel and
general inputs and outputs e.g. detectors, control signals etc.
667/HB/20200/000
Page 1-8
Issue 10
Type 400 Controller General Handbook
1.3.1.2 4 Phase Driver Board
This board contains the triacs which are used to switch the mains on to the
traffic signals, up to four Phases can be controlled by one board. It also
contains a solar cell monitor, a lamp supply Monitor and a mains zero voltage
crossover monitor.
A maximum of four boards can be fitted in the large controller and two in the
small controller.
1.3.1.3 2 Phase Driver Board and Red Lamp Monitor
This board is similar to the 4 Phase Driver Board except that only two Phases
are controlled and it has a Red Lamp Monitor which is for use with Pelican
(and certain pedestrian crossings).
1.3.1.4 Expansion I/O Board
This board adds sixteen buffered inputs and sixteen buffered outputs to the
controller.
1.3.1.5 SDE/SA Board
This board allows speed discrimination or speed assessment to be applied to
up to sixteen assessors(sixteen loop pairs).
1.3.2 Customisation
The software for the T400 consists of an operating system which is identical
in every controller, plus data to configure the operation of the controller for
the specific application.
The configuration PROM is prepared by means of a system consisting of a
desk-top microcomputer. The data is composed using question and answer
techniques in traffic engineering terms, which require no specific knowledge
of the Intel 80188 programming language. The output of the system is data
for the configuration PROM, a print-out of the controller’s specification and
functional performance, together with detail necessary for its installation. The
system is also used to prepare the conflict PROM for the conflict monitor
system and therefore allows controllers to be configured quickly and easily.
667/HB/20200/000
Page 1-9
Issue 10
Type 400 Controller General Handbook
1.4 CONSTRUCTION
The T400 is available in two sizes of outercase.
In addition, the T400 is available in two �user outercases’ as specified by the
Traffic Signals User Group (TSUG). The T400US and T400UL are described
in the �T400U General Handbook’ (667/HB/26900/000).
1.4.1 Small Outercase
See section 6 for layout details of the controller.
The small outercase is of robust construction and is intended to be ground
mounted. It has a door at the front only, access being obtained by means of
screwlocks at the top and bottom, and a key operated camlock in the middle.
All three fixings are on the left hand side.
A panel on the right hand side holds the Master switch, Master fuse,
Maintenance socket, R.C.D. and Maintenance socket fuse.
A sub chassis on the left hand side holds the power input and circuit breakers
at the bottom, the power supply and filtering, with the main processor and
phase driver boards at the top. The printed circuit boards are vertically
mounted in a small rack module.
Detectors and other ancillary equipment can be accommodated to the right of
this chassis.
4 Terminal block positions are provided on the sub-chassis, with additional
space available on the rear and right hand side walls. Fore and aft
castellated rails are provided for termination of armoured cables.
A manual panel can be fitted behind a lockable cover on the right hand side
of the cabinet.
See section 2 for details of the outercase.
1.4.2 Large Outercase
See section 6 for layout detail of the controller.
The large outercase is of robust construction and is intended to be ground
mounted. It has front and rear doors each secured with screwlocks and a key
operated camlock.
A panel on the right hand side holds the Master switch, Master fuse,
Maintenance socket, R.C.D. and Maintenance socket fuse.
667/HB/20200/000
Page 1-10
Issue 10
Type 400 Controller General Handbook
A panel in the base houses the circuit breakers, filter and power supply.
Terminal blocks are mounted at the rear of this panel, with an optional panel
being available for expansion should this be required. Castellated rails are
provided for termination of armoured cables.
Above is one or more PCB Rack modules logic rack which accommodate the
main processor board and phase driver board(s) together with boards
providing additional operating facilities.
A manual panel can be fitted behind a lockable cover on the right hand side
of the cabinet.
The remaining space above the rack module is available for the
accommodation of ancillary equipment (Detectors, OTU, OMU etc.)
See section 2 for details of the outercase.
667/HB/20200/000
Page 1-11
Issue 10
Type 400 Controller General Handbook
1.5 SAFETY
1.5.1 Controller System Checks
The Type 400 controller performs a number of tests/checks both in software
and hardware to ensure system integrity and safety.
During these checks the microprocessor and/or system hardware will switch
the signals off if any fundamental test fails. The processor will also inhibit the
re-triggering of the hardware watchdog timer which, when it expires, will
reinforce the signals-off state. An entry will also be made in the Fault Log and
the System Error LED will be illuminated.
There are some failures of a non-catastrophic nature which may occur (i.e.
battery supported data corrupted), in which case the microprocessor will reload the old data from configuration PROM, indicate the failure with the
system error LED and fault log, and continue to function.
Tests are performed in the following areas:
i)
Basic power up tests
ii)
Green correspondence
iii)
Conflict PROM
iv)
Configuration PROM
v)
T400 Firmware
vi)
Battery supported memory
vii)
Correct operation of system software
viii)
SDE/SA PCB functioning properly
ix)
Red lamp monitoring
667/HB/20200/000
Page 1-12
Issue 10
Type 400 Controller General Handbook
1.5.2 Power up Checks
When power is applied to a T400 controller, basic system checks are
performed before the traffic signals are illuminated. These are:
i)
RAM test
ii)
CRC check of system firmware (program errors)
iii)
CRC check of configuration data (configuration errors)
iv)
CRC check of battery supported timings
v)
Real-time Clock
Note: CRC (cyclic redundancy check) coding is a very powerful error
checking technique employed in computer communication systems.
1.5.2.1 RAM Test
A non-destructive read/write test is performed on the battery supported
memory to ensure that all RAM is working. If this test fails the fault is logged
(if possible), the microprocessor halts, the watchdog will not be re-triggered,
and the signals will not be switched on.
1.5.2.2 System Firmware Test
The system PROM is checked against its respective CRC digits to ensure
that the program data is still intact. If the test fails the fault is logged, the
watchdog is not re-triggered, and the signals will not be switched on.
1.5.2.3 Configuration PROM Test
The configuration PROM is checked against its own individual CRC digit to
ensure data validity. If the test fails the fault is logged, the watchdog is not retriggered, and the signals will not be switched on.
1.5.2.4 Battery Timing Test
The battery supported timings are checked using the CRC digits for each
area protected. If that test fails then the error is logged, old timing reloaded
from configuration PROM, and a comparison made between battery memory
of configuration PROM. If still faulty, the watchdog is not re-triggered and
signals are not switched on.
1.5.2.5 Real-Time Clock
The Real-time Clock (i.e. duration of power failure) is checked to ensure that
it has not exceeded the limit value specified in the configuration. If the test
fails the error is logged and the master time clock system is disabled (i.e. CLF
and timeswitch facilities will not be available).
667/HB/20200/000
Page 1-13
Issue 10
Type 400 Controller General Handbook
1.5.2.6 I/O Expansion Tests
The configured number of I/O Expansion boards is tested to ensure that they
are present.
1.5.2.7 Phase Driver Tests
The Phase Driver cards are tested to ensure there is the correct number
present and that they are in the correct position.
1.5.3 Green Correspondence Tests
During normal operation of the T400 traffic controller, a number of system
tests are continuously performed on the state of the signal greens.
The controller employs two independent green monitor systems, one based in
Software and the other based in Hardware.
1.5.3.1 Software
The microprocessor updates the signal lamps status information every 20mS
and during this time it also reads the state of the green signals as seen by the
green monitor circuit. If there is a mismatch between the state of the greens
output and the state read back, the processor will perform a number of retests, and if the error is persistent it will be logged, indicating which green(s)
was at fault, and the signal will be switched off.
Also during this time a number of tests are performed on the Independent
Hardware Monitor system to ensure that the data stored in the conflict
EPROM matches that stored in the configuration EPROM, and that the green
comparator circuit and signal lamp supply relay driver is still functioning
properly.
1.5.3.2 Hardware Green Conflict System
The independent hardware green conflict monitor system comprises:
i)
Dual green voltage detectors, the outputs of which are compared to
ensure that they are still functioning.
ii)
Green conflict monitor PROM which stores all the permitted and nonpermitted signal combinations. Should a conflict occur, the output of
the PROM monitor, which is also monitored by the software, is passed
through a delay network and then removes the drive to the signal lamp
supply relays. Under normal circumstances, the software will remove
power from the signal lamps before the hardware does, thus providing
a duplicate system.
667/HB/20200/000
Page 1-14
Issue 10
Type 400 Controller General Handbook
Should the hardware system detect an error and switch the signals off, a
signal is returned to the microprocessor which also reinforces the signals off
condition.
1.5.4 System Background Test
During any spare time the microprocessor continuously tests the following
areas:
i)
CRC check of system firmware (program errors)
ii)
CRC check of configuration PROMs
iii)
CRC check of battery supported timings
iv)
Software watchdogs for both the main system, the SDE/SA and the
integral OTU/LMU processors.
1.5.4.1 Check of System Firmware
The test described in Section 1.5.2(1.5.2.2) is repeated.
1.5.4.2 Check of Configuration PROM
The test described in Section 1.5.2(1.5.2.3) is repeated.
1.5.4.3 Check of Battery Support
The check of the battery support of timing data is divided into two areas:
i)
ii)
Battery supported phase timings, etc.
Battery supported time switch settings and CLF timings.
A failure of a test in the i) area will be logged, the original timing information
will be copied from the configuration EPROM into the RAM, and a
comparison made. If the memory is still faulty, the watchdog will not be retriggered, and the signal will be retriggered and the controller will work to the
original configured timings.
A failure of a test in the second area will be logged, the old timing information
will be restored and checked as above, but if an error still occurs, the master
time clock system will be disabled, otherwise the master time clock system
and CLF functions will work to the original configured data.
On a pelican controller if either of the above checks fail then it will be logged
and all lamps are switched off. Manual intervention (i.e. RFL=1) and power
OFF/ON is required to restore normal operation (i.e. to restore the lamps to
ON)
667/HB/20200/000
Page 1-15
Issue 10
Type 400 Controller General Handbook
1.5.4.4 Software Watchdogs
The system also incorporates an internal software watchdog which checks
that the following operations are being performed:
i)
ii)
iii)
iv)
The main 200mS scheduler is running the correct number of modules.
The 20mS scheduler is running the correct number of modules.
Memory checks are still being performed.
Continued operation of the SDE/SA processor.
If any failure is detected, the hardware watchdog re-trigger is inhibited.
1.5.5 Operation of the Safety System
To prevent the possibility of a hazardous signal condition being displayed,
the supply to the signals is switched off when any of the following conditions
occur:
-
The green conflict monitor detects a green conflict condition present on
the signal drive outputs which connect to the green lamps.
-
The microprocessor performs a green conflict test on the green conflict
monitoring system and does not receive back from the system the
response that is expected.
-
The hardware comparator on the green monitor circuit sees a
discrepancy between the outputs from the dual monitoring channels.
-
The microprocessor performs a test on the hardware comparator and
does not receive back the response that is expected.
-
The microprocessor monitors the state of the green signal feeds via the
green monitor circuit, and non correspondence is detected between
these and the green states that the microprocessor has previously
requested.
-
The watchdog facility detects that the microcomputer processing
operations have deviated from normal.
The green conflict monitor system monitors the mains voltage feeds that
supply the green signals. The monitor consists of two independent channels,
one channel monitors the positive mains half cycles of the green feeds and
the other monitors the negative half cycles of the same feeds.
The opto isolated outputs from these two independent channels connect to
the green monitor circuit on the Main Processor Card. A hardware
comparator on this card compares the two channels which should be the
same. The output from this comparator, together with the negative half cycle
channel signals, are fed to the microprocessor. The microprocessor can
667/HB/20200/000
Page 1-16
Issue 10
Type 400 Controller General Handbook
disconnect the negative half cycle channel input from the green voltage
detector circuit and apply its own signals instead. In this way it can test the
green conflict monitor system and test the hardware comparator. The
microprocessor can also monitor the state of the green signal feeds via the
opto isolated inputs.
The Main Processor card holds the conflict PROM which produces a nonconflicting output only provided a non-conflicting pattern of greens is
indicated by the negative half cycle channel signals. The output of this PROM
together with the output from the hardware comparator are fed via a delay to
the contactor drive circuits. This controls the relays A and B which supply the
mains power to the phase drivers.
A watchdog trip occurs if the microcomputer fails to trigger the watchdog
circuit within nominally 500mS. To trigger the watchdog the microcomputer
has to write to two particular addresses correctly within 8us of each other.
This normally happens every 200mS. The trip operation removes the drive
signal from lamp supply contactors which in turn removes the supply to the
lamps.
1.5.6 Red Lamp Monitoring
To prevent the possibility of a hazardous signal condition being displayed,
the following checks are made on the vehicle red lamps.
On a intersection with audible or tactile pedestrian indications, the controller,
using an ancillary processor card (see section 6.4.8), monitors the current
following through the conflicting vehicle phases’ red lamps. If two or more
lamps fail on the same phase, then the conflicting pedestrian phases are
inhibited from appearing.
On a part-time intersection, all the vehicle red lamps are monitored by the
ancillary processor card. If two or more lamps fail on the same phase, then all
the controller lamps are switched off.
On a mid-block controller (e.g. pelican), each vehicle approach is monitored
by the hardware of the 2-phase phase driver board (see section 1.3.1). If any
monitored approach has no vehicle red lamps illuminated, then all the lamps
are switched off.
667/HB/20200/000
Page 1-17
Issue 10
Type 400 Controller General Handbook
2. SPECIFICATION
2.1 MAINS SUPPLY
The following table shows the supply voltages which may be used:
Nominal
Voltage
240
230
* 220
* 200
120
110
Minimum
Voltage
192
192
188
170
96
96
Maximum
Voltage
264
264
252
229
132
132
Peak
Voltage
276
276
264
240
The peak voltage levels shown in the above table have a half hour rating.
(* - The auto-transformer facility is required for these voltages.)
It is recommended that the signals are supplied at the nominal mains voltage
during bright. i.e. For a 200 volt nominal supply, use 200 volt
transformer/bulbs. (See Appendix D for details of Tuen Mun requirements).
PROSPECTIVE SHORT CIRCUIT CURRENT OF THE SUPPLY MUST NOT
EXCEED 16,000 AMPS.
Frequency:
50Hz В±2Hz or
60Hz В±2Hz (factory selectable)
Mains Brownout:
Continues operating with up to 50mS loss of mains.
Mains Fail:
Restart without operator intervention.
Battery Support:
Provides support for the following during power failures.
(a) Clock Synchronisation (programmable upto 31 days).
(b) Timing Data (greater than one year).
Dimming Voltage:
120, 140, 160 V rms
Solar Cell Input:
Dimming cannot be provided at low mains supply
voltages, e.g. 120v or less, as solar input operating
voltages are as follows:Bright to Dim > 140v RMS
Dim to Bright < 22v RMS
Note: Dimming is available on 50-0-50 volt controllers.
The Type 400 controller solar cell enables the controller to identify the light
level and thus dim the signals when it is dark. The switch is set to operate at
55 lux and release at 110 lux. The voltage range for the device is 240v В±
20%.
667/HB/20200/000
Page 2-1
Issue 10
Type 400 Controller General Handbook
2.1.1 Electrical Noise
2.1.1.1 Supply Transients
The T400 can withstand the following transients on its supply as required in
MCE 0141.
В±100% Supply R.M.S. voltage for 10mS
В±200% Supply R.M.S. voltage for 1mS
В±300% Supply R.M.S. voltage for 0.02mS
В±500% Supply R.M.S. voltage for 0.005mS
2.1.1.2 Electrical Interference
The T400 Controller has been designed to create very little electrical
interference by the use of mains filters and solid state lamp switching control.
The mains filters protect the incoming mains supply from any T400 generated
signals. The lamp switches are switched at zero cross-over of the mains
supply to reduce any switching transients.
The switching of the signals for dim/bright lamps changeover is controlled
carefully to ensure the inductive switching does not cause interference.
The T400 controller design is also extremely tolerant of externally generated
electrical interference. Care is taken to avoid earth loops using a �Star’ point
earthing system to which the cabinet, the cabinet doors, the internal
metalwork, the junction cabling and the mains earth is connected.
Extra logic supply filtering is provided by the switched mode power unit.
The arrangement and partitioning of the controller equipment is carefully
arranged to reduce electrical noise.
The PCBs have a gridded zero voltage track layout with extensive decoupling
of logic supplies. Unused inputs are connected to the logic supplies to ensure
their logic state.
The phase switching system has isolation provided by opto-SCR’s and zero
crossing switched triacs for the mains switching. The circuit includes a
snubber filter circuit which aids triac switch off when an inductive circuit is
connected.
667/HB/20200/000
Page 2-2
Issue 10
Type 400 Controller General Handbook
2.2 DETERMINATION OF LOADING, SELECTION OF DIMMING TRANSFORMER
& LAMP FUSE
This section describes the method used to determine that the controller can
supply the total lamp load required, how to select the correct dimming
transformer and lamp fuse and how to determine the overall power used for
estimation of site running costs.
2.2.1 Controller Load
Typical supply requirement for a controller including dimming transformer
(excluding lamp loads, detectors and O.T.U) is:
-
75 watts
-
Siemens St. or Microsense detectors require 6 watts per unit and the
Sarasota MTS36Z (2 channel) or MTS38Z (4 channel) detectors
require 3 watts per unit. (NB The power consumption is the same for
both 2 and 4 channel units.)
2.2.2 Lamp Drive Capability
Amps
20A
Max
Power
(Watts)
4800W
No. of
Tungsten
Halogen HI
Lamps (63W)
76
Maximum lamp load for one phase
driver card (including red/amber)
10A
2400W
37
Maximum load for one triac output on a
phase driver card
4A
960W
15
Maximum supply for regulatory signs
(76 volt-amps per sign)
5A
1200W
15 Reg. Signs
Maximum lamp current that the
controller can supply including
regulatory signs and short term
illumination, i.e. red/amber.
Note 1:
The 5 Amp Regulatory Signs supply may be extended to a 10
Amp supply using the Mod kit 667/1/20699/000. (Note that total
controller supply is still limited to 20 Amps and that a 45A Master
switch fuse must be fitted).
Note2:
The regulatory signs supply on a T400L can also be extended
without reduction in Lamp drive capability by means of an Excess
Current Regulatory Signs Mod Kit (667/1/20699/001). This
667/HB/20200/000
Page 2-3
Issue 10
Type 400 Controller General Handbook
involves separating the Live and Neutral feeds to the Regulatory
signs from the signal feeds. This will allow for up to 10A
(unfiltered) for the Regulatory signs and up to 20A for the signal
lamps.
Note 3:
The Lamp and Wattage columns are equivalents for the currents
shown, based on a 240 volts supply.
Note 4:
If the lamp load is 13A up to 20A then a 45A Master Switch kit,
667/1/20246/000, must be used.
2.2.3 Selection of Dimming Transformer
Calculate the Total average signal lamp power as follows and using the
figures in Table .
Total average signal Lamp Power is the sum of the signal lamp power plus
the sum of the Wait indicator power. For the theoretical junction (Figure 2.2)
this would be:One lamp per signal head @ 63W x 12 signal heads
Wait indicators at 40W x 4
Total average signal lamp power
=
=
=
756W
160W
916W
Note: When selecting the dimming transformer the peak lamp power is not
used as the transformer can withstand the overload for the 2 second
Red / Amber period.
Table 2.2.3(a) Lamp Load Per Aspect (Watts)
Tungsten filament
65 watt WAIT Indicator
40 watt WAIT Indicator
50 watt High Intensity
100 watt High Intensity
Regulatory sign (wattage) (Use this for
estimation of power consumption)
Regulatory sign (Volt-Amps)
(Use this for calculation of current)
Bright
65
65
42
63
120
30
Dim
160V
53
53
25
33
60
-
Dim
140V
27
-
Dim
120V
35
35
1
20
40
-
76
-
-
-
Note that the values given in the above table relate to the average lamp
power plus power losses involved in driving the lamp.
Now using Table choose which dimming transformer is required for the
dimming voltage required.
667/HB/20200/000
Page 2-4
Issue 10
Type 400 Controller General Handbook
For the theoretical junction, using the figure obtained above (916W) and
160V dimming the transformer required would be the 1kVA version. (Note that
in this case the same transformer would be chosen regardless of the
Dimming voltage required.)
Table 2.2.3(b) Selection of Dimming Transformer.
Dimming
Voltage
120v
140v
160v
Max. Lamp Power @ 240v
Dimming
Transformer
load < 2830W
2830W < load < 4090W
4090W < load < 4560W
load < 2260W
2260W < load < 3400W
3400W < load < 4560W
load < 2000W
2000W < load < 2800W
2800W < load < 3960W
1.0 kVA
1.5 kVA
2.0 kVA
1.0 kVA
1.5 kVA
2.0 kVA
1.0 kVA
1.5 kVA
2.0 kVA
Max. Number
Of lamps
Illuminated
Continuously
49
73
98 Note 1
40
59
78 Note 1
35
50
66
Notes:1.
The absolute maximum number of lamps supported in these cases is
limited by the Lamp fuse in Bright condition. This also applies to short
time illumination e.g. Red / Amber periods. See also section 2.2.2.
2.
All lamps are assumed to be tungsten halogen (63W bright). See table
2.2.3(a) for ratings at dimmed voltages.
2.2.4 Calculating The Lamp Supply Fuse Required
In order to calculate the lamp supply fuse required the worst case red/amber
is used, i.e. the red/amber during which the most signal heads are at
red/amber. For the theoretical junction (Figure 2.2) this is during the move 2
to 1 with 5 signal heads at red/amber.
The lamp power is then re-calculated using 126 Watts for every signal head
at red/amber (assuming 63W lamp power). This gives us the peak lamp
power e.g. for our theoretical junction Figure 2.2.
Signal heads at red/amber x 126 watts
Signal head with 1 lamp illuminated x 63 watts
Every WAIT indicator illuminated x 40 watts
5 x 126
7 x 63
4 x 40
=
=
=
630W
441W
160W
1231W
This is divided by 240 volts to give us the peak lamp current:
i.e. 1231/240 = 5.2 Amps.
667/HB/20200/000
Page 2-5
Issue 10
Type 400 Controller General Handbook
Then from the following table we derive our HRC fuse and hence the Master
switch fuse:Table 2.2.4 HRC and Master Switch Fuse Selection
Peak Lamp Current
Up to 7A
7A to 10A
10A to 13A
13A to 15A
15A to 20A
H.R.C. Fuse
20ET
25ET
40ET
40ET
55ET
Master Switch Fuse
30A
30A
30A
45A
45A
For the theoretical junction this would lead to a choice of a 20ET HRC fuse
and a 30A fuse in the Master Switch.
Note 1
The Regulatory Signs do not have any impact on the selection of
the HRC fuse.
Note 2
If 15A to 20A lamp load and up to 10A of Regulatory signs is
required then the excess Regulatory signs current kit is required as
Note 2.
Note 3
The xxET type fuses are selected for their high current fast blowing
characteristic. This provides protection for the phase drive triacs.
Note 4
The numbers associated with ET fuses do not indicate the fuse
rating. e.g. A 20ET fuse is not for 20A loads.
667/HB/20200/000
Page 2-6
Issue 10
Type 400 Controller General Handbook
2.2.5 Calculation Of An Intersection’s Power Requirements For Running Costs
Estimate
The following worked example is based upon a 240 volts mains supply.
Firstly the Total average lamp power for the junction is calculated. Secondly
the Total average lamp power is added to the Total average controller power:
This gives the total average junction power which a local authority may use to
estimate running costs.
i.e. Total average junction power
=
Total average lamp power +
Total average controller power.
Total average lamp power is calculated as follows:For every signal head, 1 lamp is illuminated at 63 watts, every WAIT indicator
is illuminated at 40 watts and every Regulatory sign is illuminated at 30W.
Therefore, considering our theoretical junction (Figure 2.2), we have:1 lamp per signal head at 63 watts
Every wait indicator illuminated at 40 watts
One Regulatory Sign at 30W.
63 x 12
40 x 4
30 x 1
Total average Lamp Power is
756Watts
160Watts
30Watts
946 Watts
Total average controller power is calculated as follows:Average Controller power + Average Detector Power. See section 2.2.1.
A controller with dimming is rated at 75 watts.
Detector cards are rated at 6 watts/card for every Siemens ST detector.
Therefore for our theoretical junction (Figure 2.2) the total average controller
power is:1 x Controller
1 x Siemens ST detector
75 Watts
6 Watts
Total average controller power
81 Watts
667/HB/20200/000
Page 2-7
Issue 10
Type 400 Controller General Handbook
For the total average junction power to aid local authorities with running cost
estimates, the total average lamp power must be added to the controller
average power.
Total average Junction power is calculated as follows:Total average lamp power
Controller power
Total average Junction Power
946 Watts
81 Watts
1027 Watts
If it required to make an estimate of running costs which include the period of
time that the signals are dimmed this can be approximated as follows:Total average Junction Power (Dimmed) is :Total average Signal Power * (Dimmed Voltage / Nominal Mains voltage) plus
Total Regulatory signs power plus Total average Controller Power.
Therefore for the theoretical junction :Total average Junction Power (Dimmed)
=
(160v/240v)x(946W-30W) +81W +30W
=
722 Watts
Note 1
The power used by the regulatory signs for estimation of running
costs is approximately 30W.
For fusing purposes the regulatory signs are rated at 76 VA due
to the inductive nature of the load they present to the supply.
Ensure that the 76VA figure is used when assessing whether to
use a 5A or 10A fuse.
Note 2
The controller power should also include any additional
equipment supplied by the controller. This may include, for
example, OTU, OMU or Auxiliary detector power supply.
667/HB/20200/000
Page 2-8
Issue 10
Type 400 Controller General Handbook
Figure 2.2 - Theoretical Junction
C
C
D
D
A
B
E
E
NRT
C
A
A
STAGE 1
STAGE 2
B
STAGE 3
C
D
A
E
B
667/HB/20200/000
Page 2-9
Issue 10
Type 400 Controller General Handbook
2.2.6 Regulated Logic Supplies
+5v (В± 5%) @ 5 Amps with over-voltage and over-current protection.
+12v (В± 10%) @ 0.1 Amps with over-current protection.
-12v (В± 10%) @ 0.1 Amps with over-current protection.
2.2.7 Regulated Interface & Detector Supplies
(a)
The logic PSU also provides a 24v supply to the power interface
circuits for the controller together with some spare capacity for
powering detector cards.
+24v (В± 10%) @ 2 Amps with over-current protection.
The spare capacity is between 1.1 and 1.7 Amps dependent on the
number of I/O and SDE cards fitted; see the T400 Facilities Manual
(667/EB/20200/000) for details.
(b)
If the power provided by the 24v logic supply is insufficient, an
additional power supply may be used to supply power to internal or
external detection equipment. Two versions of this supply are
available.
+27.5v (В± 4%) @ 2 Amps or 4 Amps.
This supply voltage has been specified to overcome the voltage drop
on feeders and to remove the need for supply regulation at remotely
situated detection equipment.
NOTE
Facilities exist for separately powering detectors. Refer to Above
Ground Detectors Handbook, 667/HE/20665/000).
667/HB/20200/000
Page 2-10
Issue 10
Type 400 Controller General Handbook
2.2.8 Audible Supplies
The Audible power supplies on the T400 are designed to provide a dc
voltage between 10 and 24 volts, and typically provide 50mA at 18v
dc.
Audible and tactile units used must operate correctly over the voltage
range 10 to 24 volts dc.
Audible units recommended and supplied by STCL which meet this
requirement are; Sonalert Malary SC628P, Highland Electronics type
SC628P and Roxborough type SPCI535A4
Audibles:-
Tactiles:-
667/HB/20200/000
667/4/04785/000
Highland Electronics type SC628P (was Sonalert Malary
SC628P), and Roxborough type SPCI535A4
667/7/17390/000
PELICAN currently Radix RS250 or RS252
667/7/17390/001
INTERSECTION currently Radix RS251 or RS252
Page 2-11
Issue 10
Type 400 Controller General Handbook
2.3 FUSE RATINGS
Electricity Board Cut-out
- Dependent on lamp load, see below.
FS1 Master Switch Fuse
- Dependent on lamp load, see below.
FS2 Maint’ce Socket Fuse
- 5Amp HRC cartridge fuse to BS1361
FS3 OTU/OMU Supply Fuse*
- 5Amp HRC cartridge fuse to BS1361
FS4 Optional Supply Fuse*
- 5Amp HRC cartridge fuse to BS1361
FS5 Reserved for future use
-
FS6 Reserved for future use
-
FS7 Lamp Supply Fuse
- Dependent on lamp load, see below.
FS8 Controller Switch Fuse
- 30Amp HRC cartridge fuse to BS1361
FS9 Reg Signs & Solar Cell
- 5Amp HRC cartridge fuse to BS1361
FS10 Switched Signs Supply
- 5Amp HRC cartridge fuse to BS1361
FS11 Alt. Reg. Sign Supply
(heavy current controller)
- 5Amp HRC cartridge fuse to BS1361
Logic PSU Mains Input Fuse
- Farnell P.S. 3Amp A.T.(1ВјxВј) Ceramic
- OR, Weir 4Amp A.T. fastblow HRC
Detector PSU Mains Input Fuse*
- 2Amp Hitron - No fuse
- 4Amp Hitron - 2.5Amp (20x5mm) Delay
Fail Flasher Fuse
- 20Amp HRC cartridge fuse to BS1361
Phase Driver Fuse
- 10Amp QB (518/4/97020/120)
* If required:
Lamp Load
2A Hinchley 2Amp (20x5mm) Anti-surge
4A Hinchley 4Amp (20x5mm) Anti-surge
Electricity
Board Cut-out
FS1 Master
Switch Fuse
FS7 Lamp Supply Fuse
†Up to 7A
25Amp fuse
15A HRC fuse
20ET - 518/4/90287/003
7A to 10A
30Amp fuse
30A HRC fuse
25ET - 518/4/90287/004
10A to 13A
30Amp fuse
30A HRC fuse
40ET - 518/4/90287/005
13A to 15A
45Amp fuse
45A HRC fuse
40ET - 518/4/90287/005
15A to 20A
45Amp fuse
45A HRC fuse
55ET - 518/4/90287/006
†( Low current controller requiring 15A Mod Kit 667/1/20246/001)
HRC fuse 5Amp
518/4/90638/OOO /000
667/HB/20200/000
15Amp
/003
20Amp
/004
Page 2-12
30Amp
/005
45Amp
518/4/90637/003
Issue 10
Type 400 Controller General Handbook
2.4 PHASES
Maximum number of software phases for small T400 Controller = 16
Maximum number of software phases for large T400 Controller = 16
Maximum number of hardware phases for small T400 Controller = 8
Maximum number of hardware phases for large T400 Controller = 16
Maximum number of hardware plus software phases = 16
2.5 STAGES
Maximum of 16 (Note:- Stage 0 is normally ALL RED)
2.6 TIMINGS
All controller timings are stored in EPROM at configuration time. These
timings are subsequently transferred to battery supported RAM. Once in RAM
most timings can be varied by handset commands (see section 7). However,
should the total power failure time be long enough to drain the battery
supporting the RAM and cause loss of data, (i.e. typically four years), the
controller will revert to the original timings in EPROM.
Some timings considered to be safety timings cannot be changed by handset,
these are typically the Amber and Red/Amber periods. These timings can,
however, be changed at configuration time to suit other signal sequences,
export requirements etc.
Following is a summary of some of the timings available within the Type 400
controller. It also shows their upper and lower limit values and where
applicable the configurable limits. All timings are in seconds unless otherwise
marked.
Tolerance
All timings, except CLF and Master Time Clock, are derived from the crystal
frequency which has a tolerance of 35 parts per million. An additional error,
due to random signals not being synchronised to the clock pulse, may add up
to 200mSec to the time.
If the result of the above timings is required to change the signal lamps, a
further error may occur, which may be up to a max. of 21 mSec.
The set-up accuracy of the real time clock and offsets calculated from it will
be 1 sec. The average long term drift will be 1 sec. per year or better, subject
to the quality of the mains supply.
667/HB/20200/000
Page 2-13
Issue 10
Type 400 Controller General Handbook
Lower
Limit
(sec)
Upper
Limit
(sec)
Resol’n
(sec)
Config’ble
Lower
Limit
Config’ble
Upper
Limit
Minimum green
0
255
1
per phase
per
phase
Maximum green (4 sets)
0
255
1
per phase
per
phase
0.0
31.8
0.2
1 value
1 value
Conflicting phase change
intergreen
0
199
1
per
change
(256)
1 value
Starting intergreen
0
255
1
1 value
1 value
All red extension
0
31.8
0.2
-
-
All red maximum
0
255
1
-
-
Phase delay
0
255
1
1 value
1 value
Pedestrian blackout/
Flashing Green Man
0
255
1
1 value
1 value
Pedestrian window
0
255
1
-
-
Hurry call delay
0
255
1
1 value
1 value
Hurry call hold
0
255
1
1 value
1 value
Prevent hurry call
0
255
1
1 value
1 value
Hurry call watchdog
0
500
2
-
-
Hurry call request watchdog
0
255
1
-
-
Call delay period
0
255
1
-
-
Cancel delay period
0
255
1
-
-
255
1
-
1 value
General Timing Period
Green extension
Hurry Call Timing Period
Detector Timing Period
D.F.M.
*
†*
0
†Active DFM times are specified in minutes and inactive DFM times are specified in hours.
The value zero gives a one minute D.F.M. time for test purposes.
667/HB/20200/000
Page 2-14
Issue 10
Type 400 Controller General Handbook
Lower
Limit
(sec)
Upper
Limit
(sec)
Resol’n
(sec)
Config’ble
Lower
Limit
Config’ble
Upper
Limit
Linked pedestrian controller
release (conditioning timer)
0
255
1
-
-
C.L.F. group time‡
0
255
1
1 value
1 value
C.L.F. offsets
0
255
1
-
-
Monitor time
0
2550
10
-
-
Emergency gap
0
255
1
-
-
Priority extension (4 sets)
0
255
0.2
-
-
Priority maximum (4 sets)
0
255
1
-
-
Priority inhibit (4 sets)
0
255
1
-
-
Phase compensation (4 sets)
0
255
1
-
-
Priority 1st delay time
0
255
1
1 value
1 value
Priority 2nd delay time
0
255
1
1 value
1 value
0
55
1
-
-
Amber leaving
3
-
-
-
-
Red/Amber
2
-
-
-
-
Fixed Vehicle Period
20
60
1
1 value
1 value
Pelican all-red time
1
3
1
1 value
1 value
Vehicle Green Min. time
6
15
1
1 value
1 value
Vehicle Extension time
0
4
1
1 value
1 value
Vehicle Green Max. time
10
60
1
1 value
1 value
Linking Timing Period
Priority Timing Period
Speed Discrimination Period
SDE/SA extra clearance
Fixed Timing Period§
Pelican/Pedestrian Timings
‡
В§
Cycle length equals the sum of all group times in a plan.
These are timings not alterable by the handset and are fixed in the configuration PROM.
667/HB/20200/000
Page 2-15
Issue 10
Type 400 Controller General Handbook
Lower
Limit
(sec)
Upper
Limit
(sec)
Resol’n
(sec)
Config’ble
Lower
Limit
Config’ble
Upper
Limit
Pedestrian Green time
4
9
1
1 value
1 value
Intergreen step 0 - red & fl/grn
0
2
1
1 value
1 value
Intergreen step 1 - fl/amb & fl/grn
6
18
1
1 value
1 value
Intergreen step 2 - fl/amb & red
1
2
1
1 value
1 value
Pedestrian Green time
3
15
1
1 value
1 value
Intergreen step 0 - red & blackout
5
15
1
1 value
1 value
Intergreen step 1 - red & red/man
1
8
1
1 value
1 value
MCE0125Timings
MCE0145Timings
667/HB/20200/000
Page 2-16
Issue 10
Type 400 Controller General Handbook
2.7 MASTER TIME CLOCK & CABLELESS LINK FACILITY SUMMARY
Master Time Clock
• Timing Sources - Mains 50Hz (60Hz Wire link and configuration).
• Standby Timing - On board crystal and battery support programmable up
to 31 days. Accuracy of standby crystal oscillator is 35 PPM
• Programmable changeover to mains synchronisation.
• Facility for synchronising the real time clock or group timer from existing
UTC
• Number of time switch settings - 64
• Number of time switch functions - 3
(a)
Isolate controller
(b)
Introduce a CLF plan
(c)
Introduce a set of events
(11 types of event)
(16 sets of combinations of events)
Cableless Link Facility
Number of plans
8
Number of plan influence tables per stream
8
Number of groups per plan
16
Number of group influences
10 types
2.8 MODES OF OPERATION
• Vehicle actuated (SDE/SA can be added to V.A)
• Timetable selected fixed time plans either cableless linked or in isolation.
• Central computer controlled in a traffic control system.
• Fixed time
• Hurry call
• Manual
• Parallel stage streaming
• Priority
• Part time OFF/ON
• Part time Flash/Normal operation.
• Pelican VA
• Pelican Fixed Time
2.9 OUTERCASE
667/HB/20200/000
Page 2-17
Issue 10
Type 400 Controller General Handbook
SMALL
LARGE
Height (above ground level)
1170mm
1400mm
Width
465mm
660mm
Depth
370mm
490mm
Weight of bare outercase
32Kg
42kg
Assembled controller only (Including Outercase)
71Kg
90Kg
Both cases are manufactured in aluminium and finished with grey epoxy or
acrylic paint.
In addition to the screwlocks, the main controller doors are fitted with one S18
lock per each. The key lock must not be operated unless the screw locks are
tight. ie. Unlock the door before undoing the screwlocks and only lock the
door after tightening the screw locks.
The lock used on the police manual panel is a small Yale lock with a 900
pattern barrel.
There is a facility to change the S18 lock to a Yale with an RKA27C pattern
barrel.
2.10 ENVIRONMENTAL
2.10.1 Temperature
The T400 in a grey outercase is designed to operate in external ambient
temperatures of -15ВєC to +60ВєC. A white tropical outercase may be supplied
when requested by a customer, but this does not provide any benefit with
regard to solar radiation. Use in countries where high levels of and long
periods of, solar radiation are expected, may impose restrictions on T400
hardware configuration. Contact Engineering at Poole for more details on
hardware restrictions.
2.10.2 Atmospheric
The controller is proofed against driving rain and sand, dust conditions and
industrial pollution.
2.10.3 Humidity
The equipment will withstand a temperature of 35В°C with a relative humidity
of 95%.
2.11 HANDSET INTERFACE (RS232 PORT)
Type
667/HB/20200/000
Page 2-18
Issue 10
Type 400 Controller General Handbook
RS232C CCITT V24 and V28
Method of Connection
Controller
Terminal Device
-
Cannon DP 25-way socket connector
Cannon DP 25-way plug connector
Pin Allocation
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 18
Pin 19
Pin 20
}
}
}
}
-
Protective ground
Transmit data from terminal to controller
Received data from controller to terminal
Request to send
Clear to send
Data set ready
Signal ground
Rx Signal detect (reserved)
5V supply (controller 5 volt logic/user supply)
Ground supply
Data terminal ready
Bit Format
START
(SINGLE
BIT)
1
(LSB
2
•
3
•
4
•
5
•
6
•
7
MSB)
PARITY
(EVEN)
STOP
(SINGLE
BIT)
Baud Rate
1200 Bd
Mode
Full duplex
Character Set
ISO Alphabet No. 5 (ASCII)
667/HB/20200/000
Page 2-19
Issue 10
Type 400 Controller General Handbook
3. TRAFFIC FACILITIES
The following list of controller functions and facilities is a brief overview of the
capabilities of the T400 Controller.
Each heading is an extract from handbook 667/EB/20200/000 where further
details on each subject can be found. At the back of this section, a copy of
our specification sheets are included which, will indicate the data required to
configure these facilities.
3.1 STAGES
3.1.1 Stage Facilities
16 stages (0-15)
Stage 0 - all red
Stage 1 - Normally start up stage (which cannot be deleted)
3.1.2 Allocation Of Phases
Phases are allocated to stages. However each phase in a stage runs
independently and therefore the timings of a stage depend upon the
interaction of the phase timings within that stage.
3.1.3 Stage Active
A stage is considered active when:All fixed phases allocated to the stage are at green and all fixed and non
fixed phases not allocated to the stage are at red.
3.1.4 Stage Terminating
A stage is considered to be terminating when:The first phase which has had R.O.W, (i.e. been at green) during the stage,
loses right of way.
3.1.5 Inter Stage Period
The interstage period is the time between one stage terminating and another
stage becoming active.
3.1.6 Stage Movement Restrictions
Ignore moves:- The controller can be configured to ignore certain possible
moves from a stage, and so will look for other acceptable moves.
Prohibited moves:- The controller can be configured such that it will never
make certain stage to stage moves.
667/HB/20200/000
Page 3-1
Issue 10
Type 400 Controller General Handbook
Care must be taken when deciding to use prohibited moves, to ensure that a
“lock up” situation cannot occur.
Alternative moves:- Alternative moves can be configured for those moves
prohibited, thus providing an allowed movement to help prevent lock-up.
Once in the alternative stage, the controller will perform its normal movement
decision programme in order to decide which stage to move to next. This
therefore means that this movement is not a move to a stage via an
alternative stage. If a move via a stage to another stage is required other
move restrictions have to be applied to the alternative stage.
Permitted moves:- All stage to stage moves not configured as any of above
types.
3.1.7 Prevent Stages/Phases
Stages and phases can be prevented from appearing provided all safety
requirements and controller cycle requirements are met. The facility can be
introduced when user defined conditions are satisfied, for example by using
special conditioning and/or master time clock.
3.2 PHASES
3.2.1 Types Of Phases
Traffic phase
Pedestrian phase
Pelican vehicle phase
Pelican pedestrian phase
Green arrow phase:- Filter green arrows or indicative green arrows.
Dummy phase
Switched sign phase
LRT phase - Uses a pedestrian phase with different aspect display.
3.2.2 Conflicting Phases
Real phases which cannot appear together for safety reasons are considered
to be conflicting and as such must have intergreen times between them.
3.2.3 Opposing Phases
If two phases oppose each other then a demand for one will start the max
green timer of the other phase if it is at green.
667/HB/20200/000
Page 3-2
Issue 10
Type 400 Controller General Handbook
3.2.4 Phase Delays
Phases can be delayed:-
(a) from losing right of way and
(b) from gaining right of way.
3.2.5 Timing Periods
See section 2.6 for Phase timing periods.
3.2.6 Limiting Values
This is a value which can be defined during configuration for certain timings,
which then ensures that the appropriate times can not be set above or below
the limit value, by use of the handset.
(See section 2.6).
Note:
Prom held values can be set lower than the limit value. These are
transferred to the RAM at initialisation an the controller works to
these values. The handset may only alter the times within the
limits specified. If they have been altered, they cannot be set
back down to the original value without the complete set of
timings being loaded from prom by re-initialising the controller.
3.2.7 Conditions Of Appearance For Phases
Type 0:-
Always runs if the stage to which it is allocated becomes active.
Type 1:-
Will only appear whenever its associated stage becomes active, if
a demand is inserted before the start of the preceding interstage.
Type 2:-
Will only appear whenever its associated stage becomes active, if
a demand is inserted. No limitations on when demand is inserted.
Type 3:-
This is as type 2, however once a stage associated with a type 3
phase becomes active, a window timer can be started. During this
window time, a demand for the phase will cause it to appear. After
the expiry of the window timer, demands for the phase will be
stored but not actioned. The window timer will start when its
associated stage is active and there is an opposing demand,
however, if the controller is in UTC mode the window timer will
start as soon as its associated stage becomes active.
3.2.8 Fixed Phase
Real or dummy phases with a type 0 condition of appearance.
667/HB/20200/000
Page 3-3
Issue 10
Type 400 Controller General Handbook
3.2.9 Non Fixed Phases
Real or dummy phases with type 1, 2 or 3 conditions of appearance.
3.2.10 Conditions Of Termination For Phases
Type 0:-
Phase terminates at end of associated stage.
Type 1:-
Phase terminates when an associated phase gains right of way.
Type 2:-
Phase terminates when an associated phase loses right of way.
3.2.11 Early Termination Of Phases
Available using two consecutive stages, or phase (losing) delays.
3.3 DEMANDS AND EXTENSIONS
3.3.1 Types Of Demands
Latched
-
Demand remains until phase is served
Unlatched
-
Demand is cleared if the demand condition ceases before
phase is served.
3.3.2 Origins Of Demands And Extensions
(a)
On-street detection equipment
(b)
Pedestrian push button
(c)
Revertive demands
(d)
U.T.C demand bits
(e)
Demands and/or extensions can be inserted when set conditions arise
(special conditioning).
(f)
LRT requests provided via interface from LRT interrogator.
3.3.3 Repeat Pulses
Controllers when linked, can repeat demands and/or extensions between
them.
667/HB/20200/000
Page 3-4
Issue 10
Type 400 Controller General Handbook
3.3.4 SDE/SA
Extensions for high speed vehicles.
3.3.5 Handset
Demands and extensions can be inserted for phases via the handset.
3.3.6 Operation Of Demands And Extensions During Certain Modes
3.3.6.1 Manual, Fixed Time And Start-Up
While in manual mode the demands and extensions are disregarded,
however when leaving this mode demands are inserted (if configured) for all
non running phases.
Demands and extensions are normally disregarded during fixed time mode.
The controller cycles using fixed time periods for each stage. As an
alternative, the fixed time facility can be configured to run to the current
maximums. Using this latter facility demands are used, thus allowing demand
dependence of some phases in fixed time. (Note: the controller mode will
show VA mode.)
Demands are inserted for all phases during start-up unless otherwise
specified.
3.3.6.2 U.T.C
For U.T.C it is possible to configure the following.
1.
Which phases and/or stages have latched or unlatched demands
inserted when a certain U.T.C demand bit is applied.
2.
Which phases are extended by which U.T.C demand bits.
3.
Demand dependent force bits and for each force bit which demands are
to be considered.
3.3.6.3 C.L.F Mode
Extensions are disregarded during C.L.F mode, except if an extension exists
when a phase is terminated then a revertive demand is inserted. However it is
possible to configure demand dependent moves to stages during C.L.F. This
667/HB/20200/000
Page 3-5
Issue 10
Type 400 Controller General Handbook
is achieved by selecting the group influence as a demand dependent move to
a stage and specifying the stage.
Three alternative movements can also be specified by selecting the �Add
demand dependent move’ group influence.
3.3.6.4 Call/Cancel
There are up to 8 call/cancel units (0 to 7) available which may be used for
turning movements or in conjunction with queue loops or switched facilities.
The input to a unit must be active for a “call period” before the output
changes to active and similarly the input must be inactive for a “cancel
period” before the output changes to inactive.
Where call/cancel is used to control an early cut off, there are 3 control
techniques:(i)
Normal system D detectors are used to call and extend the main stage
and the call cancel loop is used to call and extend the turn stage.
(ii)
If a turn call exists then the system D detectors providing extensions for
the main stage from the approach with the turn will be inhibited. Then
during the turn stage the above system D detectors will also extend the
turning stage.
(iii)
System D detectors for the main stage on the approach with the turn
will extend both the main stage and the turn stage.
The choice of which of the above methods of control to use depends on the
relative amounts of traffic for each movement. See the facilities handbook for
a fuller description.
667/HB/20200/000
Page 3-6
Issue 10
Type 400 Controller General Handbook
3.4 HIGH SPEED VEHICLE DETECTION
3.4.1 Speed Discrimination Equipment (SDE)
3.4.1.1 Double SDE
- One assessment point (2 loops) per approach lane.
- Extensions given for vehicles above a set speed threshold.
- Extra clearance to extend an intergreen period.
3.4.1.2 Triple SDE
- As double SDE except with 2 assessment points (2x2 loops) per approach
lane.
- The threshold speed for the inner assessment point will be different from
that of the outer assessment point.
3.4.2 Speed Assessment (SA)
Fixed extensions are given but the delay between a vehicle crossing an
assessor and the start of the extension, varies depending upon speed of
vehicle.
3.4.3 Assessors Available
There are up to 16 assessors (0 to 15) available for use on SDE or SA. Each
assessor may be checked with a Soundmark test set by plugging into the
socket provided and selecting the assessor on the thumb wheel switch on the
SDE/SA PCB.
3.4.4 Extra Clearance Periods
Each phase which is equipped with SDE or SA can be allocated an extra
clearance period to extend the subsequent intergreen. The extra clearance
period for each phase will be introduced if any of the following conditions
occur:(a)
An SDE or SA extension is active for the phase during its amber
leaving state.
(b)
Any speed measurement detector does not detect a vehicle during the
associated phase green period.
667/HB/20200/000
Page 3-7
Issue 10
Type 400 Controller General Handbook
(c)
Optionally, any extension, (speed extension, green extension or
Priority extension), is active for the phase when it changes from green
to amber leaving.
The condition in (c) is normally disabled for individual phases at the time of
configuration. Speed extensions will still request extra clearance because of
the operation of condition (a).
An extra clearance period will be given under any mode of control, i.e.
manual, VA, fixed time, CLF, UTC, vehicle priority or hurry call. Its effect is to
increase all the inter-green timings for the phase which is being given the
extra clearance, and also to increase the phase change delay times for
gaining phases.
If the intergreen is not dependent on the SDE/SA phase inter-green time,
(because another losing phase has a longer inter-green time), then the extra
clearance period may not actually delay the appearance of the gaining
phase.
The range of the timing period for the extra-clearance is 0 to 50 seconds in 1
second steps for each SDE/SA phase.
The programmed value may be changed via the handset using the SCT
command.
3.4.5 SDE/SA on Green Arrows
Where these are single aspect, the red and amber drives of the Phase Switch
PCB are not available to drive other green arrows, as they must be
programmed as 3-aspect to get the amber signal to meet the requirement of
6.4, even though only the green arrow is connected.
3.4.6 Other Manufacturers Loops
The SDE/SA facility can be configured to operate with loop spacings of 12ft
instead of 10ft.
667/HB/20200/000
Page 3-8
Issue 10
Type 400 Controller General Handbook
3.5 MODES
These are listed in a typical order of priority.
3.5.1 Start-Up Mode
The controller will start up in a set and controlled manner to ensure the safety
of the junction users.
3.5.2 Part-Time Mode
The signals can be switched on or off at set times or under set conditions.
3.5.3 Urban Traffic Control
The T400 controller can be linked to a central computer for remote control via
an OTU etc.
3.5.4 Priority Mode
The T400 can be equipped to give a rapid change to right of way for vehicles
fitted with special vehicle transponders.
3.5.5 Hurry Call Mode
The T400 can be configured such that on receipt of one of two special input
signals, it will rapidly change to a selected stage to give special junction
conditions.
3.5.6 Selected Manual Control
Selecting this mode by operating a push button on the manual panel allows
the policeman to control the operation of the controller manually.
3.5.7 Selected Fixed Time or VA or CLF.
There are three pushbuttons on the manual panel which may be used to
select:-
or
Fixed Time.
VA
CLF
as the working mode.
667/HB/20200/000
Page 3-9
Issue 10
Type 400 Controller General Handbook
3.5.8 Normal Mode
Selected by push button on the manual panel.
The normal position allows the controller to choose its own working mode
using its mode priority table and taking into account all other necessary
influences.
3.5.9 Cableless Link Facility (CLF) Mode
Linking two or more controllers using synchronised clocks.
3.5.10 Vehicle Actuated Mode
Stage change decisions made using vehicle detection equipment.
3.5.11 Fixed Time Mode
Controller cycles using fixed time periods. This is obtained by manual
selection or as an alternative to VA.
3.6 MASTER TIME CLOCK
A real time clock can be provided which can control all time dependent
functions, e.g.:Introduction of C.L.F plans
Switch to an alternative MAX set.
Switch an input active or inactive.
Switch an output active or inactive.
Switch a sign on or off.
Delete a Phase.
Delete a Stage.
Switch an audio indicator off.
Switch to part time mode.
Switch a flag readable in special conditioning.
Switched DFM
Plus many other functions which can be constructed using special
conditioning.
3.7 LINKING
The linking facilities can be used in numerous applications e.g.:-
667/HB/20200/000
Page 3-10
Issue 10
Type 400 Controller General Handbook
(a)
Linking a T400 to a pelican controller
(b)
Linking a T400 to another traffic controller
(c)
Passing signals to other controllers such a detectors (demands etc),
hurry call requests etc.
(d)
Linking O.T.U control and reply signals to other controllers.
3.8 ALTERNATIVE SIGNAL SEQUENCES
User defined signal sequences can be implemented when requested.
667/HB/20200/000
Page 3-11
Issue 10
Type 400 Controller General Handbook
3.9 INPUTS & OUTPUTS
The hardware can provide a maximum of 96 lines as follows:Main Processor Card (one of these in every controller)
Two variants of the main processor card exist. The I/O characteristics of each
are detailed below.
/001 variant - Intersection controller processor board.
2 input ports providing a total of 16 lines (8 per port), 2 lines of which are
buffered. Buffered inputs 1 and 2 should be used first on all applications.
1 output port providing 4 lines, buffered via relays (2 normally open and 2
normally closed).
Note:- Only two buffered inputs are recognised by the configurator.
/002 variant - Pelican controller processor board.
2 input ports providing a total of 16 lines (8 per port), 4 lines of which are
buffered. Buffered inputs 1 and 2 should be used first on all applications.
1 output port providing 4 lines, buffered via relays (2 normally open and 2
normally closed).
Expansion I/O Card (up to 3 of these can be fitted in a controller)
2 input ports providing a total of 16 buffered lines (8 per port).
2 output ports providing a total of 16 buffered lines (8 per port).
SDE/SA Card
4 input ports providing a total of 32 buffered lines (8 per port). 32 inputs
caters for 16 assessors. Any inputs not used for SDE/SA may be used for
other purposes e.g. detectors.
Connections
The ports on the Expansion I/O, Main Processor and SDE/SA PCBs are
accessed by sockets on the rear. The Expansion I/O Board has 4 sockets,
the Main Processor has 2 and the SDE/SA PCB has 2.
Normally equipment is connected to the controller inputs via the controller
Expansion I/O Boards, which isolate the controller logic from the outside
world. However, if the equipment is within the controller cabinet, it is possible
to connect directly to the controller Main Processor unbuffered inputs without
going via Main Processor buffered inputs or Expansion I/O Boards.
667/HB/20200/000
Page 3-12
Issue 10
Type 400 Controller General Handbook
This is only possible if the device to be connected to the controller input has
isolated (voltage free) reed relay contacts, or the Solid State equivalent, as
an output with the following impedance characteristics.
Device output low impedance < 2 kΩ
Device output high impedance > 300 kΩ
This will not operate within a standard solid state output as specified in
MCE0100.
Such output contacts must be commoned to Controller 0 volts if required.
N.B. If controller inputs are to be monitored by an Outstation Monitoring Unit
(part of a Remote Monitoring System), then the controller inputs cannot be
unbuffered - they MUST be buffered.
Port Allocation
Port numbers are allocated as per the following table:
Board Type
CPU
CPU
CPU
Expansion I/O
Expansion I/O
Expansion I/O
Expansion I/O
SDE/SA
SDE/SA
SDE/SA
SDE/SA
Port No
0
1
11*
(a)
(b)
(c)
(d)
6
7
8
9
Port Type
INPUT
INPUT
OUTPUT
INPUT
INPUT
OUTPUT
OUTPUT
INPUT
INPUT
INPUT
INPUT
Connector name
PLE
PLE
PLC
PLB
PLC
PLD
PLE
PLB
PLB
PLC
PLC
Where (a), (b), (c) and (d) are ports on the Expansion I/O Boards numbered
using the rotary switch on the front of each board:-
(a)
(b)
(c)
(d)
*
INPUT
INPUT
OUTPUT
OUTPUT
Expansion
I/O Board 0
2
3
4
5
Expansion
I/O Board 1
6
7
8
9
Expansion
I/O Board 2
10
11*
-
Expansion
I/O Board 2
10
11*
Port 11 can be defined as either 4 bits of output (CPU) or 8 bits of input
or output (Expansion I/O board 2).
Note: The Tuen Mun contract requires a specific I/O allocation which is
detailed in Appendix D.
667/HB/20200/000
Page 3-13
Issue 10
Type 400 Controller General Handbook
3.10 MANUAL PANEL FACILITIES
There are four versions of the Intersection Manual Panel:(a)
A full Intersection controller manual panel.
(b)
A Police manual panel.
(c)
An Internal Manual Panel
(d)
A basic manual panel.
For further information refer to section 6.
3.10.1 Full Intersection Controller Manual Selection Panel
The Manual Panel incorporates the following:•
Eight stage selection push buttons and associated indicators
•
Five mode selection pushbuttons
•
Signals ON/OFF switch
•
Lamp test push button
•
Prohibited move indicator
•
Hurry call indicator
•
Higher priority indicator
•
3 spare indicators e.g. for priority, UTC Active
•
3 spare push buttons (which can be used alone or in conjunction with the
Indicators) e.g. for DFM Reset, Dim over-ride, Remote Reconnect, Part
Time Select, Flashing Signals, Alternative Maximum, Audio Signal
Override etc. Some of these facilities would only be used abroad. Refer to
667/2/20645/000 for the T400 Manual Panel label for these facilities.
3.10.2 Police Manual Panel (Hong Kong)
The Police Manual Panel incorporates the following:•
DFM LED.
•
Signals ON/OFF switch.
•
Manual step-on control enable and disable pushbuttons.
•
Optional proximity switch for disabling step-on when the manual panel
door is shut (always used for Hong Kong).
•
Select All Red button.
•
Manual step-on button.
•
�Active’ LED indicator.
This is not DTp approved and is normally only used on export orders.
667/HB/20200/000
Page 3-14
Issue 10
Type 400 Controller General Handbook
3.10.3 Internal Manual Panel (Hong Kong)
This is fitted inside the controller and access is limited to persons who have
controller door keys. It incorporates the following:•
Eight stage selection push buttons
•
Five mode selection pushbuttons and associated indicators
•
Lamp test push button
•
Prohibited move indicator
•
Hurry call indicator
•
Higher priority indicator
•
1 spare indicator
•
Override Dim pushbutton and indicator
•
Signals Flash
This panel would normally be used in conjunction with a Police Manual panel
which is fitted with a signals on/off switch.
3.10.4 Basic Manual Panel
•
A basic panel consisting only of a signals ON/OFF switch & cabinet alarm.
3.10.5 Optional Manual Panel Facilities
•
Fixings for British Telecom terminations
3.11 SIGNAL AND DETECTOR ISOLATING SWITCHES
Signals Isolating Switch
A single pole 30 amp switch is fitted to the controller switch DIN rail to isolate
the signal supply.
Detector Isolating Switch
A double pole 30 amp switch is fitted to the controller switch DIN rail. One
pole isolates the 24v detector supply. The second pole can be used to isolate
the 27ВЅV detector supply if fitted in addition to the 24v supply.
667/HB/20200/000
Page 3-15
Issue 10
Type 400 Controller General Handbook
3.12 T400 FAILURE FLASHER FACILITY (EXPORT ONLY)
This facility uses a type 400 failure signal to release a set of contactors which
switch between the T400 phase output drives and the mains drive from the
fail flasher board. The combination of fault log entries which cause the
contactors to switch is pre-programmed into the configuration. The speed or
frequency of the flashing is controlled by 2 link fields on the fail flasher board.
One link field governs the on time, the other controls the off time, both are
programmable from 0 to 1.260 seconds in 20mSec steps.
This facility can be disable (if facility is fitted) by removing the 20 amp fuse on
the flasher pcb.
The contactors can be wired to flash either the red, amber or green aspect of
any phase.
3.13 HANDSET
The handset available has alpha numeric displays and keyboards. When in
use the handsets plugs into the RS232 port socket, on the front of the C.P.U
board. Using a handset it is possible to view and/or change some of the data
held in the T400 battery supported R.A.M. e.g. timings etc. Handsets are sold
as separate items.
1.
G.R. Electronics Handset.
2.
Epson with standard terminal software.
3.
Epson with intelligent terminal software.
Note: This provides facilities such as:(a)
auto dump of controller times.
(b)
hard copy print outs, etc.
See handset handbook 667/HH/20200/000.
4.
Any computer terminal with an RS232 port socket capable of operating
at 1200 Bauds.
See section 6.3.9 for more information on individual handsets.
667/HB/20200/000
Page 3-16
Issue 10
Type 400 Controller General Handbook
3.14 SPECIFICATION SHEETS (667/DJ/15900/000)
A copy of the specification sheets is provided in Appendix 0 of this handbook,
with a guide in section 7. It should provide an idea of the flexibility of the
controller and the data required to configure the facilities available. Spare
sets can be ordered by quoting the above number. These sheets, if filled in at
the time of the order, will reduce the delivery time, misinterpretations and
reduce the possibility of additional costs.
Note: Certain contracts use a subset of these, see Appendix 0 for Tuen Mun
specification sheets.
667/HB/20200/000
Page 3-17
Issue 10
Type 400 Controller General Handbook
4. PELICAN/PEDESTRIAN CONTROLLER
4.1 GENERAL
There are a number of basic configuration PROMs, covering the following
configurations: single or dual stream, MCE0125, MCE0145, Puffin or Toucan.
One of these basic configurations is selected for the controller and it is further
altered via the handset i.e. timings may be altered within approved ranges, IO
lines on the controller may be set up to have different functions etc. Selection
of some facilities may require extra hardware, e.g. extra Expansion I/O card.
Timings and selections made via the handset are stored in battery backed
RAM which is continually validated by CRC checking.
There are two modes of operation of a Pelican/Pedestrian controller:
4.1.1 Fixed Vehicle Period mode
In this mode the controller runs a set Vehicle Green period (ranging from 20
to 60 seconds in 1 second increments) after which it will service a pedestrian
demand if one exists. If no pedestrian demand is present it will rest on vehicle
green until there is a ped. demand which it will then service immediately.
4.1.2 Pelican VA mode
In VA mode, the controller will respond to vehicle extension detectors once
the minimum vehicle green has expired in the following manner :
(a) Extending/Maximum Change
If a pedestrian demand is inserted but vehicles are passing
continuously over the detectors, the vehicle green will be extended to a
preset maximum, after which the pedestrian demand is serviced. In this
instance, for safety reasons, a “maximum change” all-red period will be
inserted between the vehicle green and the pedestrian green after the
amber leaving period. If no pedestrian demand exists the vehicle max.
green timer will not be started and the vehicle phase will rest in green.
(b) Gap Changing
If a pedestrian demand is inserted where vehicles are not passing
continuously over the detectors, the controller will wait until no vehicle
extensions are being timed and then service the pedestrian demand,
before the vehicle green max. timer has timed out. In this instance, a
“gap change” all-red period alterable between 1 and 3 seconds, is
inserted between the vehicle and pedestrian greens.
667/HB/20200/000
Page 4-1
Issue 10
Type 400 Controller General Handbook
(c) Pre-timed Maximum vehicle green
If this mode is selected, the controller will start the max. vehicle green
timer as soon as vehicle green is gained, instead of waiting for an
opposing/pedestrian demand. If no pedestrian demand occurs before
the max timer expires the controller will rest in vehicle green until a
pedestrian demand is inserted which it will then service immediately by
completing a “max change” to pedestrian green, even if a vehicle is
inserting a continuous extension. If a pedestrian demand is inserted
before this max. timer has expired there can still be a gap change if
there are no vehicle extensions present.
4.2 PELICAN/PEDESTRIAN TIMINGS
The minimum green, maximum green and vehicle extension timings for a
pelican are alterable via the handset within ranges approved in MCE0125
and MCE0145. These are different to those for MCE0141 vehicle phases and
thus they are accessed by different handset commands.
There are other alterable timings for the all-red time from vehicle green to
ped. green in UTC and Local Link modes following the removal of PV and
PV1 respectively. If both of these signals occur simultaneously then the UTC
signal PV always overrides the Local Link signal.
If SDE/SA is selected (via the handset) and fitted on the controller then all of
the vehicle green to pedestrian green all-red times are fixed at three seconds.
If there has been a DFM failure on the controller then a maximum all-red time
is included in the change from vehicle green to pedestrian green for safety
reasons.
If the Vehicle Detector Checking facility has been enabled and there has
been no activity on one or more of the vehicle extension during the vehicle
green period, then a maximum all-red time is included in the change from
vehicle green to pedestrian green for safety reasons.
4.2.1 Puffin Sequence Timings
The Puffin controller sequence is similar to an intersection pedestrian, since
there are no flashing aspects. However, the blackout period of the
intersection pedestrian is replaced with an extendable clearance period,
during which red is displayed to traffic and pedestrians. This clearance period
is extendable up to a maximum by detecting pedestrians on the crossing.
Pedestrians are also detected as they wait to cross, by means of a kerbside
detector. If after a demand has been registered no-one is still waiting, the
pedestrian demand is cancelled.
667/HB/20200/000
Page 4-2
Issue 10
Type 400 Controller General Handbook
The Puffin operates in conjunction with Red lamp monitoring, SDE/SA, UTC,
CLF etc. in the same manner as the Pelican.
The Puffin Extendable Clearance Period
The clearance on the change from pedestrian green to vehicle green and is
composed of:•
a configured minimum red period, followed by
•
a variable red period (extendable by �on-crossing’ detectors up to a
configured maximum), followed by
•
a clearance red period (this is the �long’ clearance period if the
variable red has been extended up to its maximum otherwise the
�short’ clearance period is used).
4.3 MANUAL PANEL FACILITIES
When the T400 is used as a pedestrian controller the Manual Panel is
usually equipped as a �basic manual panel’ providing only cabinet alarm
together with a signals on/off switch (see Figure 6.3.5.4).
If specifically requested then a full pedestrian manual panel may be provided
which duplicates a few of the facilities which are provided via the handset
(see section 5) onto pushbuttons.
A brief description of the full pedestrian manual facilities are described in the
following sections. For a �basic panel’ these facilities are available via the
controller handset (see section 5).
4.3.1 Select VA/FVP
The mode on the pelican/pedestrian controller may be selected between FVP
and VA. However the Select VA function is only actioned if VA mode has
been enabled via the handset. The associated LED reflects the position of
the pushbutton only and this is not necessarily the mode that is currently
running.
4.3.2 Continuous Ped. Demand
When this button is pushed, the associated LED is illuminated and a
permanent demand is inserted for the pedestrian phase of that pelican
stream.
667/HB/20200/000
Page 4-3
Issue 10
Type 400 Controller General Handbook
4.3.3 Continuous Vehicle Extension
When this button is pushed, the associated LED is illuminated and the
vehicle extension timers are continually reset so that in VA mode the vehicle
phase always runs to a max. When this switch is released, the extension
timer running continues to time out and after it has expired, the pelican
stream reverts to normal operation.
4.3.4 DFM Reset
This button is used to reset the DFM lamp and only has that effect if all faulty
detectors/pedestrian pushbuttons have changed state since the fault was
registered.
4.3.5 Auxiliary LEDs (AUX1, AUX2, AUX3) and Switches (SW1, SW2, SW3)
There are two functions available which may be assigned to any of these
three switches and LEDs. The requirements in terms of switches and LEDs
for these two functions are given below:
Remote Reconnect : Both a switch and LED are required.
Computer Control LED : LED alone is required.
667/HB/20200/000
Page 4-4
Issue 10
Type 400 Controller General Handbook
4.4 HANDSET
On street selection of pelican facilities by the handset can be carried out. A
list of the pelican handset commands is given in section 5. The following
settings can be altered on the pelican controller :4.4.1 Timings
Handset commands are provided to control the pelican timing steps
separately from the intersection timings.
Use of the intersection timing commands (e.g. MIN, MAX, EXT, IGN, IGS etc.)
have no effect on the pelican timings.
Local linking times for link delay, link window, override and link fail times are
also alterable on the handset.
4.4.2 Speed Discrimination (SDE/SA)
No SDE/SA operation, Double or Triple SDE or SA operation and the number
of speed assessor units required for the Pelican/Pedestrian may be selected
via the handset.
Both of the standard PROMs have capability for SDE/SA facilities but only for
the DTp standard loop spacing of 12ft. If a non standard loop spacing is
required then a non standard configuration PROM will be required.
4.4.3 Manual Facilities
When a controller is equipped with a �basic manual panel’, handset
commands are provided to support the selection and display facilities which
were provided on the old style �full manual panel’ (see section 5 for details).
667/HB/20200/000
Page 4-5
Issue 10
Type 400 Controller General Handbook
4.5 I/O LINE ALLOCATION
Each of the following functions may be allocated to an IO line :Input functions
UTC ped. inhibit PV
UTC ped. demand PX
UTC take over TO (enable SC, PV, PX)
UTC switch to FVP working
UTC switch to alternative timings
UTC Dim Override / remote dim control DO
UTC vehicle extensions inhibit SC
local link disable LL
local link ped. inhibit PV1
local link ped. demand LD
call/cancel ped. demand CC
3 vehicle extension detectors
4 push button ped. demand
2 Kerbside detectors (Puffin Only)
4 �On crossing’ detectors (Puffin Only)
*
*
*
Output functions
UTC vehicle green confirm GX
UTC wait indicator confirm WT
UTC ped. green confirm PG
DFM fail confirm DF
UTC signals off confirm SO
local link disable confirm LL
UTC bright confirm
remote reconnect RR (active state = disconnect)
link out (vehicle green confirm)
link out (bright confirm)
Kerbside detector test signal (Puffin Only)
A description of each of these I/O functions is given in section 4.10.
* - These output signals must be allocated to normally closed (N/C) contacts.
The first two bits of the CPU output port (port 11) are N/C contacts. The first
two bits of each output port on the I/O expansion board are defaulted to the
N/O state. However each of these output bits are connected to relays with
changeover contacts. Hence they may be wired to give N/C operation. All
other output bits operate in the N/O state.
667/HB/20200/000
Page 4-6
Issue 10
Type 400 Controller General Handbook
In addition it is possible to :(a)
enable/disable DFM on each input (DFS) and define the group (DGP)
(b)
define the action taken when DFM detects a fault (DFA) as:- continue to use input as before
- override input state to active
- override input state to inactive
(c)
invert the sense of particular inputs (IPS)
(d)
define number of red lamp monitor channels used on each pelican
traffic phase (RLM)
4.6 WAIT INDICATORS
This facility allows the user to select (via the handset using the WTI
command) whether the wait indicator is illuminated by any of the following
demands:
- Pushbutton ped demands
- UTC ped demands
- Manual Panel Ped demands
- Local Link ped demands
- Handset ped demands
4.7 AUDIO CONTROL AND MONITOR
An output activates the audio unit during the ped steady green time. An input
monitors the drive voltage to the audio unit and a check is made that the
monitored state corresponds with the requested state. Repeated failure of the
check causes the lamps to be turned off within 500mS (from the point at
which the first occurrence of the fault was detected) and an entry made in the
fault log. Since the audio drive is derived from the ped green supply, turning
the signals off removes the audio drive.
4.8 GREEN CONFLICT FAULT ACTION
On detection of a green conflict (as indicated by monitoring the output of the
green conflict PROM) the controller turns all the controller lamps and audio
indicators off. The lamps will remain off until manually reset (RFL=1), using
the handset, turning the power off and then restoring the power.
4.9 RED LAMP MONITORING
The current through the vehicle red lamps is monitored to check that there is
at least one vehicle red lamp showing while there is a steady green signal
showing to pedestrians. If a fault occurs, the controller turns all the signals
and the audio indicators off. The lamps will remain off until manually reset
667/HB/20200/000
Page 4-7
Issue 10
Type 400 Controller General Handbook
(RFL=1), using the handset, turning the power off and then restoring the
power.
4.10 DESCRIPTION OF I/O LINE FUNCTIONS
4.10.1 UTC Facilities
• UTC Ped. Inhibit (PV)
This input signal prevents the pedestrian phase on a pelican. When
PV is released, vehicle extensions will be inhibited for a period
specified via the handset. Even if PV is re-applied during this period it
will have no effect.
• UTC Ped. Demand (PX)
This input signal puts in a request for the pedestrian stage of a
pelican.
• Vehicle Extensions Inhibit (SC)
This input signal forces the controller to ignore all vehicle extension
requests. To ensure safety of operation, the vehicle to ped. change
becomes a UTC. all-red change rather than a gap change. The UTC
all-red change time is alterable via the handset.
• UTC Transmission Confirm (TC) or Takeover Control (TO)
The TC signal, if allocated to an IO line, is received at the controller
from the OTU if valid data has been received by the OTU. The TO
signal is very similar in effect except that it is transmitted from the UTC
Central Office and not from the OTU and it too signifies that valid data
is being sent by the UTC Central Office. The presence of either of
these signals disables the Local Link facility.
• Computer Control LED on the Manual Panel
The rules governing the illumination of this LED are as follows:
(1)
If the TC/TO function has not been assigned to an IO Line then
the presence of PV alone lights this LED.
(2)
If TO has been assigned to an IO line then the LED is only
illuminated when TO is present in conjunction with PV.
(3)
If TC has been assigned to an IO line and selected to control the
LED, then the presence of this TC signal alone lights the LED.
(4)
If TC has been assigned to an IO line and selected not to control
the LED, then the LED is illuminated only when both PV and TC
are present (as in case 2).
667/HB/20200/000
Page 4-8
Issue 10
Type 400 Controller General Handbook
• Switch to FVP mode
This input disables Pelican VA mode and thus forces the controller to
run in FVP mode. This signal only has an effect when the Pelican is
running VA mode. VA mode is active under the following conditions :
(a) VA operation is selected via the handset.
AND
(b) VA mode is activated using the VA switch on the manual panel.
• Switch to Alternative Timings
This input signal forces the Pelican to switch to the first alternative set
of timings.
• UTC Dim Override (DO)/Local Link Dim Request
One of these two types of remote dimming can be selected via the
handset for the pelican/pedestrian. The main difference between the
two types is:
a)
the UTC input signal overrides any request for the controller to
be in the dim state provided by the solar cell output and thus
provides a “Bright Request” signal.
b)
the Local Link Dim Request signal is required for a slave pelican
controller in a linked dimming situation and provides a “Dim
Request” signal. This means that a master controller which has a
solar cell controlling its dimming facility may be able to pass on
its dim/bright state to another (slave) controller without a solar
cell.
• Local Link Disable (LL)
The effect of this input signal is to disable the Local Link Pedestrian
Inhibit facility (PV1) which is detailed in
• Vehicle Green Confirm (GX)
This output signal indicates that the vehicle phase is showing green on
the street. This output signal must always be assigned to a Normally
Closed relay so that it fails to the inactive (closed contact) state.
667/HB/20200/000
Page 4-9
Issue 10
Type 400 Controller General Handbook
• Wait Indicator Confirm (WT)
This output signal indicates that the Wait indicator for the pedestrian
phase is illuminated on the street. This output signal must always be
assigned to a Normally Closed relay so that it fails to the inactive
(closed contact) state.
• Pedestrian Green Confirm (PG)
This output signal indicates that the pedestrian phase is showing
green on the street. This output signal must always be assigned to a
Normally Closed relay so that it fails to the inactive (closed contact)
state.
• DFM Fail Confirm (DF)
This output signal indicates when the DFM lamp has been illuminated.
This output signal should be assigned to a Normally Open relay so
that it fails to the active (open contact) state.
• Signals Off Confirm (SO)
This output signal indicates that the signals on the CPU
pelican/pedestrian are off for whatever reason i.e. Signals switched off
from the Manual Panel, Red Lamp Monitor failure, Conflict detected
etc. This output signal should be assigned to a Normally Open relay so
that it fails to the active (open contact) state.
• Local Link Disable Confirm (LL)
This output signal indicate that the local link facility on the controller
has been disabled, for whatever reason i.e. Local Link disable switch
on Manual Panel active, UTC local link disable control bit active,
timeswitch function etc.
• UTC Bright Confirm
This output signal indicates that the signals on the controller are in the
bright state, for whatever reason i.e. daytime operation, dim override
switch on Manual Panel active, UTC dim override control bit active etc.
• Remote Reconnect (RR)
This reply bit is generated when the Remote Reconnect Switch on the
Manual Panel when fitted/configured is activated (indicated by the
illumination of the associated LED). This switch indicates to the UTC
central office that the controller is ready to resume under UTC control.
667/HB/20200/000
Page 4-10
Issue 10
Type 400 Controller General Handbook
4.10.2 Local Link Facilities
• Local Link Ped Inhibit (PV1)
While this signal is active, it prevents the appearance of the ped.
phase irrespective of demands, subject to the effect of the Override
timer described below. A delay time can be set via the handset so that
there is this delay between the PV1 signal being released and the
Inhibit on the controller being lifted. After this, a Window time which is
also alterable via the handset, can come into effect. This is the time
after the Inhibit has been lifted during which the controller ignores
vehicle extension detectors and looks for a pedestrian demand to
service, even if PV1 has been reapplied during this time. If the window
timer expires and PV1 has not been reapplied the controller reverts to
its normal (FVP or VA) working mode.
If PV1 is active the Override timer will start to time if it has been set to
a non-zero value via the handset and normally at the start of the
vehicle phase green. This override timer can optionally be selected
(via the handset) to commence timing only if a pedestrian demand is
present while the vehicle phase is at green. This timer is reset when
the PV1 signal goes inactive. If it times out one of two actions may be
taken, depending on handset selection :
(i)
it will ignore the PV1 signal and revert to normal unlinked
operation and only recognise the PV1 signal again if it is now
released and re-applied.
(ii)
it can operate in self resetting mode i.e. once the override timer
expires it reloads itself, introduces the Link Delay and Link
Window times and commences re-timing when either the
Window time expires or the controller returns to vehicle green
as a result of serving a Pedestrian demand during the Window
period. If PV1 is released and reapplied normal linked operation
resumes.
The Override timer is usually used only for MCE0125 pelicans and its
use is determined by checking for a non-zero timing value. There is
another watchdog mechanism used for MCE0145 pedestrian
controllers which checks that the link is not permanently operated nor
permanently released. This mechanism will be used if there is a nonzero timing value for the Link Failure Active/Inactive times (LKA/LKI).
Timeout of either of these signifies “link failure” which causes the
following actions:
Inhibit the appearance of the Pedestrian Phase.
Light the Wait Indicator
Light the Cabinet Alarm Lamp
Set a Fault Log Flag
667/HB/20200/000
Page 4-11
Issue 10
Type 400 Controller General Handbook
After a “link failure”, manual intervention is required to reset the fault
log before the controller can resume normal operation.
In certain circumstances e.g. light traffic flow, the intersection
controller will be unable to generate link inhibit release pulses often
enough to prevent the timeout of a Fail timer and in these cases a
pulse generator is required in the main controller to signify that the link
is good. The pulse generator must ensure that the link inhibit is
released and reapplied periodically to reset both the FAIL ACTIVE and
FAIL INACTIVE link fail timers. To ensure that this pulse generator
does not cause the link inhibit signal to be released erroneously
certain timing restrictions are imposed on the pulses and signals:
20ms
<
Inhibit release pulse
Inhibit Release signal
<=
>=
300ms
340ms
This means that if the signal on this line is released for less than
300ms and then reapplied the only effect will be to reset the Link Fail
Active and Inactive timers. If the signal is released for more than
340ms and then reapplied, then the effect will be to reset the Link Fail
Active and Inactive timers and to start the Link Delay timer.
• Local Link Dim Request
This input signal is treated in the same manner as UTC Dim Override
(DO) and is described in section 4.10.1.
• Local Link Ped. Demand (LD)
This input signal puts in a remote pedestrian demand.
• Link Out (Vehicle green confirm)
This output signal is essentially a Vehicle Green Confirm signal and
can be used to provide a Ped. Inhibit (PV1) to another pelican usually
in a staggered link situation. The effect then is to inhibit the ped. of the
other pelican while it itself is not in the vehicle green period.
NOTE that this does not take account of any race condition between
two controllers that are linked together and as such if the pushbuttons
of the two controllers are pressed simultaneously there is a possibility
that both pelicans could go to green at the same time and so true dual
pelican operation cannot be achieved in this manner. In order to
overcome this problem a T400 dual pelican must be used.
• Link Out (Dim Request)
667/HB/20200/000
Page 4-12
Issue 10
Type 400 Controller General Handbook
This signal is used by the master controller in a linked dimming
situation, where it is usually used to pass on the dim/bright state of the
master to the slave pelican controller.
4.10.3 Call/Cancel Function
• Call/Cancel Ped. Demand (CC)
This input signal acts as a normal call/cancel demand, in that a
demand must be present for a certain period (call time) before the
demand is accepted. Similarly if the demand disappears before the
controller has satisfied it, then it must permanently disappear for a
certain period (cancel time) before the controller will cancel the
demand. The effect of the input is to put in a demand for the
pedestrian phase.
4.10.4 Puffin I/O Facilities
• Push Button and Kerbside Detector Inputs
Two push button inputs are available on each Puffin stream. In
addition, each Puffin stream has two kerbside detector inputs which
indicate when there are pedestrians waiting to cross.
Each input from push button or kerbside detector is held active in the
controller for a configurable hold time (after the input has gone
inactive).
The pedestrian demand is only registered if the following conditions
are met:a) a push button is being pressed or hold period active
AND b) a pedestrian is being detected by the kerbside detector or the
kerbside hold period is active.
The pedestrian demand is cancelled and the wait indicator turned off
if all kerbside detectors indicate no pedestrians present for a
configured detector timeout period.
NOTE:
Pedestrian demands from UTC or local link operate as on
the Pelican controller i.e. the demand does not require the
kerbside detector to be active in order to be registered and
the demand is latched - not cleared when the kerbside
timeout period expires.
• Kerbside Detector Test Output
667/HB/20200/000
Page 4-13
Issue 10
Type 400 Controller General Handbook
One test output is provided for each Puffin stream. This output should
be wired to connect +24V through the �normally open’ relay contacts to
the detector test input on surface mounted kerbside detectors.
While there is no pedestrian demand registered, each detector is
tested at 10 second intervals. Note that the kerbside detector is tested
during the pedestrian push button hold time, providing that no demand
is registered.
The test output is driven with a 400mS pulse by the controller and a
check is made for a detector response pulse. A missing or late
response forces the detector active (within the controller) and an entry
is made in the fault log. A subsequent correct response from the
detector removes the force condition.
Detector testing is required with surface mounted detectors, but not
with �above ground’ detectors. Detector testing is enabled by default.
Testing can be disabled by de-allocating the corresponding detector
test output.
NOTE:
The test sequence results in a pulse appearing on the
kerbside detector output. This will be treated as a normal
pedestrian presence, activating the kerbside hold and
timeout periods.
• �On-crossing’ Detector Inputs
Up to 4 inputs are available on each Puffin stream. The �on-crossing’
detector indicates when there are pedestrians moving on the crossing
and is used to extend the variable clearance period on the move from
pedestrian green to vehicle green.
Any configured �on-crossing’ detector remaining inactive during a cycle
is assumed faulty and forces the following variable clearance period to
be extended up to it’s maximum. An entry is also made in the fault log.
If the detector subsequently operates correctly, then the force is
removed and normal operation resumed.
4.11 TIMESWITCH FACILITIES
• Switch Audio off
This facility allows the pelican ped. audio signal to be turned off on a
time of day basis.
• Alternative Max. sets
667/HB/20200/000
Page 4-14
Issue 10
Type 400 Controller General Handbook
There are four time sets available for each of the modes. I.e. Pelican
VA and FVP, which may be selected on a time of day basis. The
selection of these timesets is required to have a lower priority than the
UTC �Switch to Alternate Times’ signal (described in section 4.10.1).
As a result of this requirement the time switch settings will only be
effective if the UTC �Switch to Alternate Times’ signal is not active.
• Switch to FVP mode
This facility disables Pelican VA mode and thus introduces FVP mode
on the pelican/pedestrian controller on a time of day basis.
4.12 CLF FACILITIES
The only effect of CLF on a pelican controller is to provide a ped. inhibit
signal. There is a corresponding group influence to cancel this ped inhibit
influence i.e. an “Allow Ped” influence which is used to provide a ped window.
This CLF inhibit signal inhibits the Pedestrian phase for as long as this input
is active provided that there is an Allow Ped influence somewhere in the
same group. If there is no Allow Ped influence within the same group then the
CLF input has no effect.
4.13 CROSS-INHIBIT LINKING
On multi-stream Pelican controllers there are some situations when it is
desirable to prevent the pedestrian phases from running concurrently (e.g.
when two pedestrian crossings are positioned on the road where a central
island is provided). This inhibit facility can be introduced by handset
command (LKM) (see section 5 for details).
667/HB/20200/000
Page 4-15
Issue 10
Type 400 Controller General Handbook
5. HANDSET COMMANDS
Access to the T400 timings and status information is gained by entering
commands on an approved handset and interpreting the response on the
display. The pages following give an example of the types of handset codes
that can be used.
The document “Handset Command List” 667/HH/20200/000 gives up to date
information on handset operation and codes. This should be used when
operating the handset.
667/HB/20200/000
Page 5-1
Issue 10
Type 400 Controller General Handbook
(A-ACCESS LEVEL: O=OPEN, R=READ ONLY, 2=LEVEL 2, 3=LEVEL 3)
CODE
INDX1
ADF
AMX
BAS
BSA
BSR
CCI
CCP
CFE
CGR
CGT
CIC
CIL
CKL
CNN
CPL
CPT
CST
CTS
CUD
DAY
DCL
DCN
DET
DFA
DFD
DFS
DFZ
DGP
DHC
DIT
DMV
DOV
DPG
DSA
DSI
DTO
ENC
ENG
ENM
ENO
ENR
ENS
EXT
FAC
FDS
FFS
FIO
PHASE
STR’M
0-63
STR’M
0-5
0-7
0-7
0-95*
0-95*
0-95*
0-59
0-95*
0-1
0-59
0-59
0-7
0-7
0-3FFF
CODE
0-7FF
0-FFF
0-1FFF
0-7FF
PHASE
FACIL
0-127
0-63
0-139
INDX2
DATA
1
0-255
0-2
1-52
1-52
1
0-1
0-1
1
0-255
PLAN
0-1
0-2
0-255
0-255
0-255
0-2,99
0-2
0-255
PHASE
0-7,255
0-255
0-1
0-FF
0-1
0-255
T/SET
0-255
T/SET
0-255
0-1
OFFS.
0-31.8
0-95,255
667/HB/20200/000
DESCRIPTION
A
ACCEPT DETECTOR FAULT(S)
SECOND MAX PERIOD
SELECT MEMORY DISP. BASE
SET BST ADVANCE WEEK
SET BST RETARD WEEK
COMPUTER CONTROL INDICATOR
RESTORE CLF OPERATION
CONDITIONING FAC. ENABLE
CURRENT GROUP
CURRENT GROUP TIME
CONFIGURATION CODE
CROSS INHIBIT LINKING
LOAD MASTER TIME CLOCK
2nd CONTR RESET COMMAND
CURRENT PLAN
CONFLICT PROM TEST REQUEST
CURRENT STAGE IN STREAM
SELECT MST SYNC SOURCE
ASSIGN U/D UNIT TO AN INPUT LINE
MASTER TIME CLOCK DAY
DET. CALL DELAY PERIOD
DET. CANCEL DELAY PERIOD
DETECTOR INPUT SETTING
DETECTOR FAULT ACTION
DET. FAULT MONITOR TIME
DET. FAULT MONITOR DISABLE
PHASE TO BE DELAYED
ASSIGN INPUT LINE TO A DFM GROUP
HURRY CALL DELAY PERIOD
I/O DIMMING (0=UTC,1=LLINK)
PHASE DELAY MOVEMENT TABLE
DIM OVERRIDE
PHASE DELAY PERIOD
DFM SET ACTIVE FAILURE
DFM SET INACTIVE FAILURE
DFM TIME OVERRIDE
DISPLAY CONFIG. PROM DATA
DISPLAY ENG. CODE MEMORY
DISPLAY IMU SHARED MEMORY
DISPLAY OTU/LMU SHARED MEMORY
DISPLAY RAM. MEMORY DATA
DISPLAY SDE SHARED MEMORY
PHASE EXTENSION PERIOD
FACILITIES TABLE
FAULT DATA SCAN
FAULT FLAG SCAN
FUNCTION I/O ALLOCATION
Page 5-2
2
2
2
2
2
R
2
3
R
R
R
2
2
3
2
2
R
2
2
R
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
R
R
R
R
R
R
2
R
R
R
2
Issue 10
Type 400 Controller General Handbook
CODE
FIX
FLD
FLF
FRE
FVA
FVB
FVC
FVD
HHC
HKD
HPB
IFA
IFB
IFC
IFD
IGN
IGS
IOB
IOP
IPS
ITV
LAT
LFT
LKA#
LKD
LKI#
LKM
LKO
LKW
LLD
LMP
LMX
LPT
LRN
MAX
MBX
MCX
MDX
MIN
MND
MOD
MPA
MST
MTS
MTV
OFF
OMF
OTF
INDX1
INDX2
DATA
DESCRIPTION
A
STAGE
0-255 F.T. STAGE PERIOD
0-127
FAULT LOG DATA
0-63
FAULT LOG FLAG
0-2
0-100 FREE PROCESSOR TIME
STR’M
20-60 FIX. VEH. PERIOD TIME SET A
STR’M
20-60 FIX. VEH. PERIOD TIME SET B
STR’M
20-60 FIX. VEH. PERIOD TIME SET C
STR’M
20-60 FIX. VEH. PERIOD TIME SET D
0-1
0-255 HURRY CALL HOLD PERIOD
STR’M
1.0-2.0 PUFFIN KERBSIDE DET. HOLD
STR’M
1.0-2.0 PUFFIN PUSH BUTTON HOLD
0-7
0-15
0-7F
GROUP INFLUENCES COMB. A
0-7
0-15
0-7F
GROUP INFLUENCES COMB. B
0-7
0-15
0-7F
GROUP INFLUENCES COMB. C
0-7
0-15
0-7F
GROUP INFLUENCES COMB. D
PHASE PHASE 0-199 PHASE INTERGREEN PERIOD
0-199 STARTING INTGRN. PERIOD
0-2
0-1
I/O BOARD 0-2 FITTED (IF 1)
0-11
I/O PORT STATUS
0-95*
0-1
I/O LINE SENSE:0=NORM,1=INVERTED
PHASE PHASE
INTERGREEN THRESHOLD VALUE
PHASE
0.0-31.8 VARIABLE AMBER LEAVING TIME
0-15
0-255 STAGE COMBINATION DURATION
STR’M
0-255 PEL LINK ACT FAIL TIM (MIN)
STR’M
0-255 PEL LINK DELAY TIME (SEC)
STR’M
0-255 PEL LINK INACT FL TIM (MIN)
0-1
0-1
PELICAN LOCAL LINK MODE
STR’M
0-255 PEL LINK O/RIDE TIME (SEC)
STR’M
0-255 PEL LINK WINDOW TIME (SEC)
0-1
LOCAL LINK DISABLE
PHASE
1-3
ILLUMINATE PHASE ASPECT
STR’M
0-255 MAX ALL RED PERIOD
0-1
LAMP TEST
0-255 3rd RESET COMMAND
PHASE
0-255 PHASE MAX PERIOD
PHASE
0-255 SECOND MAX PERIOD
PHASE
0-255 THIRD MAX PERIOD
PHASE
0-255 FOURTH MAX PERIOD
PHASE
0-255 PHASE MIN PERIOD
0-1
MANUAL PANEL ENABLE/DISABLE
STR’M
CURRENT OPERATING MODE
0-3
0-255 MANUAL PANEL ALLOCATION
0-3
DATA SET MST SYNC CHANGE TIME
MASTER TIME SWITCH STATUS
PHASE
MINIMUM THRESHOLD VALUE
PLAN
0-1
0-255 GROUP OFFSET TIME
0-1
INTEGRAL OMU (IMU) FITTED
0-1
INTEGRAL OTU/LMU/RLM CARD FITTED
667/HB/20200/000
Page 5-3
2
R
R
2
2
2
2
2
2
2
2
2
2
2
2
3
3
2
R
2
R
3
2
2
2
2
2
2
2
2
3
2
2
3
2
2
2
2
3
2
R
3
2
R
R
2
2
3
Issue 10
Type 400 Controller General Handbook
CODE
INDX1
INDX2
OTO
PAR
PAR
PAR
PAR
PAR
PBG
PBT
PCn
PDE
PDR
PDS
PFD
PFT
PGT
PGT
PGT
PHC
PHD
PHE
PIA
PIC
PIR
PIT
DATA
DESCRIPTION
A
0-1
STR’M
STR’M
STR’M
STR’M
STR’M
0-7
PHASE
UNIT
UNIT
UNIT
UNIT
0-2
STR’M
STR’M
STR’M
0-1
PHASE
PHASE
0-15
STR’M
0-1
0
1
2
3
4
ALLOCATE AN INTEGRAL OTU OUTPUT
PEL A/R GAP CH. TIME (SEC)
PEL A/R MAX CH. TIME (SEC)
PEL A/R FVP CH. TIME (SEC)
PEL A/R UTC CH. TIME (SEC)
PEL A/R LLK CH. TIME (SEC)
IDENTIFY PUSH-BUTTON DFM GROUPS
PED BL’OUT/FL’ING GRN TIME (SEC)
PHASE (n) COMP. TIME
PRIORITY DEMAND ENABLE
PRI. DFM SELF-RESET ENABLE
DISP. PRIORITY DEM/EXTS
FIRST PRIORITY DELAY TIMER
RTC POWER FAIL LIMIT TIME
MCE0125 - PED GREEN TIME (SECS)
MCE0145 - PED GREEN TIME (SECS)
PUFFIN - PED GREEN TIME (SECS)
HURRY CALL PREVENT PERIOD
MANUAL PHASE DEMAND
MANUAL PHASE EXTENSION
PRIORITY INH. TIMER STATUS
PROGRAM PROM ID CODE
PELICAN DELAY PERIODS
PELICAN INTERGREEN TIMES: (SECS)
2
3
3
3
3
3
2
3
2
2
2
R
2
2
3
3
3
2
2
2
R
R
2
3
PIT
PIT
PIT
PIT
PIT
PIT
PIT
STR’M
STR’M
STR’M
STR’M
STR’M
STR’M
STR’M
3
3
3
3
3
3
3
0-7
0-255
MCE0125: V/ RED + P/FLGRN TIME
MCE0125: V/FLAMB + P/FLGRN TIME
MCE0125: V/FLAMB + P/ RED TIME
MCE0145: V/ RED + P/BKOUT TIME
MCE0145: V/ RED + P/ RED TIME
PUFFIN MIN. CLEARANCE TIME(SECS)
PUFFIN LONG RED EXTRA CLEARANCE
TIME
PUFFIN
SHORT
RED
EXTRA
CLEARANCE TIME
PRIORITY UNITS INHIBITED
PLAN INFLUENCE SELECTION
PLAN-GROUP TIME SETTINGS
PIT
STR’M
n2
0-3
PIU
PLI
PLT
PLAN
PLAN
PME
PMT
PMV
PRD
PRE
PRI
PRS
PSA
PSD
UNIT
0-1
UNIT
UNIT
UNIT
UNIT
GROU
P
T/SET
T/SET
PHASE
-
R
2
2
0-255
0-1
0-255
0-1
0-1
0-1
0-1
0-255
MAINTENANCE ACCESS
MONITOR TIME (0s-2550s)
PED. MOVEMENT ALGORITHM
AUTO PLAN RE-ENTRY DELAY TIME
PRIORITY REV. DEM. ENABLE
PRIORITY INH. TIMER ENABLE
AUTOMATIC PLAN RE-ENTRY SWITCH
PRIORITY STRAT. VA DEMS
PRIORITY 2ND DELAY TIMER
O
2
2
2
2
2
2
2
2
0-255
1-3
1-3
1-3
1-3
1-3
0-1
0-255
T/SET
0-255
T/SET
0-1
0-255
DATA
4-9
3-15
4-9
0-255
0-1
0-1
0-255
0-2
VARIOU
S
0
0-2
1
6-18
2
1-2
0
5-15
1
1-8
n0
2-5
n1
0-3
667/HB/20200/000
Page 5-4
3
Issue 10
Type 400 Controller General Handbook
CODE
PSE
PUI
PUP
PUT
PVE
PVG
PVI
PVM
PVP
PVS
PVU
PWN
RDF
REX
REX
RFL
RLM
RLT
RMR
RMX
RMX
SAS
SCI
SCR
SCT
SDS
SDT
SEA
SGT
SHC
SPH
SIE
STA
STP
STM
SWS
TKD
TKE
TMA
TMC
TMT
TOD
TOT
TSW
INDX1
INDX2
DATA
DESCRIPTION
A
UNIT PHASE
0-1
PRIOR. STRAT ENFOR. DEM
UNIT
0-FF
PRIORITY UNITS TO BE INH.
UNIT PHASE
PRIORITY UNIT PHASE
UNIT
PRIORITY UNIT TYPE
UNIT
T/SET 0.0-31.8 PRIORITY EXTENSION TIME
UNIT
0-255 DET. INTERRUPT PERIOD
UNIT
T/SET
0-255 INHIBIT TIME PERIOD
UNIT
T/SET
0-255 PRIORITY MAXIMUM TIME
PHASE
PRIORITY VEH. UNIT STATUS
STAGE
PRIORITY VEH. STAGE STAT.
UNIT
PRIORITY VEH. UNIT STATUS
STAGE
0-255 PED. WINDOW PERIOD
1
RESET DETECTOR FAULT MON.
STR’M
0-31.8 ALL-RED EXTENSION PERIOD
n
0.4-5.0 PUFFIN CLEARANCE EXTENSION TIME
(0.2s)
0-1
RESET FAULT LOG
STR’M
1-4
No. RLM CHANNELS ENABLED
PHASE
0-255 ENHANCED RLM PHASE DELAY TIME
REMOTE RECONNECT
STR’M
0-255 ALL-RED MAXIMUM PERIOD
n
0 - 13 MAXIMUM CLEARANCE TIME (SECS)
STR’M
0-16
PEL: No. SDE/SA ASS. USED
0-1
EXTRA CLEARANCE STATUS
0-1
EXTRA CLEARANCE REQUEST
PHASE
0-50
SDE/SA EXTRA CLEAR. TIME
0-2
PEL: SELECT - 0=NONE 1=SA 2=SDE
STR’M
0-1
PEL: SDE/SA - 0=DOUBLE 1=TRIPLE
0-1
SPEED EXTENSION STATUS
1
RESET TO GROUP 0
UNIT
HURRY CALL STATUS
PHASE
PHASE STATUS
STR’M
0-31.8 SUPPLEMENTARY I/G EXT (LMU)
CONTROLLER STATUS MESSAGE
STAGE
0-255 MANUAL STEP ON
0-3
DATA SET MASTER TIME CLOCK
0-15
0-1
SWITCH FACILITY
STR’M
2.0-5.0 PUFFIN KERBSIDE DET. TIMEOUT
0-255 1st CONTR RESET COMMAND
0-255 CONTROLLER TEST MODE (ACCESS)
0-255 CONTROLLER
TEST
MODE
(COUNTDOWN)
0-255 CONTROLLER TEST MODE (TIMER)
MASTER TIMER CLOCK SETTING
0-1
PEL TC/TO UTC BIT TYPE
0-63
0-5
DATA TIME SWITCH SETTING
667/HB/20200/000
Page 5-5
2
2
R
R
2
2
2
2
R
R
R
2
2
2
2
2
3
3
2
2
2
3
R
R
2
3
3
R
2
R
R
2
R
2
2
2
2
3
3
2
2
R
2
2
Issue 10
Type 400 Controller General Handbook
CODE
INDX1
INDX2
DATA
TWD
-
-
-
UDT
UIE
VAD
VAE
VAM
VAX
VBX
VCX
VDX
WEK
WTI
0-5
STR’M
STR’M
STR’M
STR’M
STR’M
STR’M
STR’M
STR’M
0-4
0
-
0-255
0-255
0-4
0-4
6-15
10-60
10-60
10-60
10-60
1-52
0-1
DESCRIPTION
A
TRIP WATCHDOG - WARNING - 3
CAUSES
IMMEDIATE
SHUTDOWN
CONSEQUENTLY MUST NOT BE USED
UNDER ANY CIRCUMSTANCES TO
TEST EQUIPMENT WITH SIGNALS ON
AND CONTROLLING TRAFFIC.
U/D TIMEOUT (IN 10 SECOND UNITS)
PEL UTC "PV" WINDOW TIME
PEL VA MODE
PEL VEH. GRN EXT TIME (SEC)
PEL VEH. GRN MIN TIME (SEC)
PEL VEH. GRN MAX TIME (SEC)
PEL VEH. GRN ALT1 MAX (SEC)
PEL VEH. GRN ALT2 MAX (SEC)
PEL VEH. GRN ALT3 MAX (SEC)
MST WEEK SETTING
WAIT IND ILLUMINATION
2
2
3
2
3
2
2
2
2
2
2
* = Line numbers
# = Local site approval must be sought before the use of these facilities.
667/HB/20200/000
Page 5-6
Issue 10
Type 400 Controller General Handbook
6. GENERAL ARRANGEMENT OF T400 HARDWARE
6.1 SMALL OUTERCASE
Refer to Figure 6.1 for diagrammatic layout.
6.1.1 Master Switch Panel
The mains supply is terminated by the electricity board cutout, for which a
mounting board is provided at the lower right hand side of the rear cabinet
wall.
6.1.2 Controller Panel
At the left side is a sub-chassis controller panel to which most of the
components are mounted.
At the right side is located the Master switch and fusing, together with a
Maintenance socket protected by an RCD and a fuse.
At the bottom is the controller panel switch, a mains filter, and a solid state
relay.
Above is the logic power unit and above that is the PCB module.
The controller panel can accommodate 4 x 12 way terminal blocks for
connection to street cabling e.g. detectors, lamp feeds etc.
Additional termination panels can be provided (2 max) which can
accommodate a further 8 x 12 way blocks.
Armoured cable can be secured to castellated bar positions beneath the
terminal blocks.
6.1.3 PCB Module
The main processor and phase driver boards are located at the top left of the
cabinet in a small rack module.
6.1.4 Manual Panel & Cabinet Alarm
A membrane type panel with integral indicator LEDs is fitted behind a
lockable door on the right hand side of the case. The cabinet alarm indicator
on this panel is visible to outside observation through a red coloured lens in
the Manual panel door.
667/HB/20200/000
Page 6-1
Issue 10
Type 400 Controller General Handbook
6.1.5 Uncommitted Space
The middle and upper central areas of the cabinet are available for mounting
ancillary equipment.
i.e.
Detector racks
OTU
OMU/OMCU
LMU
Table 6.1.5 Accommodation of Ancillary Equipment within a Small Outercase
Total Capacity : 17U
Combination no.
Top of Cabinet
Bottom of Cabinet
Not Preferred
Key:
3U
5U*
5U#
OMU
1
3U
3U
3U
3U
5U*
2
3U
3U
3U
5U*
3U
&
&
3
3U
3U
5U*
3U
3U
4
5U#
3U
3U
3U
5
OMU
3U
3U
6
3U
3U
OMU
= 11” Detector Rack
= Siemens OTU
= Siemens OTU or Ferranti OTU/OMU (short rack version)
= Siemens OMU
Notes:
a) These are typical combinations for general use - see drawing
667/GA/20279/000 for other combinations.
b) The above equipment is located on the small controller �Equipment
Mounting Frame’.
c)
Although the controller can accommodate a large number of
detector racks, which implies a large number of detector cards, this
will be limited in practise by the available capacity of the power
supplies provided.
d) Mounting studs for the Siemens LMU are provided on the �backwall’ of the controller cabinet.
e) Due to space restrictions it is not possible to accommodate both
the Siemens LMU and Ferranti OTU.
667/HB/20200/000
Page 6-2
Issue 10
Type 400 Controller General Handbook
Figure 6.1 - T400 In A Small Outercase
PCB MODULE
(EXPANSION)
MANUAL
PANEL
CONTROLLER
PANEL
ASSEMBLY
PCB MODULE
E
F
TERMINAL
BLOCKS
A
G
H
J
L
K
M
ADDITIONAL
TERMINATION
BLOCKS
B
N
C
R
D
T
X
P
S
W
Y
POWER
SUPPLY UNIT
MASTER
SWITCH AND
FUSE RAIL
CONTROLLER
SWTICH AND
FUSE RAIL
667/HB/20200/000
Page 6-3
Issue 10
Type 400 Controller General Handbook
6.2 LARGE OUTERCASE
Refer to Figure 6.2(a) and Figure 6.2(b) for diagrammatic layout.
6.2.1 Master Switch Panel
The mains supply is terminated by the electricity board cutout for which a
mounting board is provided on the Master switch panel at the cabinet rear
right hand side.
Above this is located the Master switch and fusing together with a
maintenance socket protected by an RCD and fuse.
6.2.2 Distribution Panel
The front face of the distribution panel holds the remaining power
components:Controller switch and fuses mount on a DIN rail with expansion if required.
The lamp dimming transformer, mains filtering, solid state relay and logic
power supply.
The rear of the distribution panel accommodates terminal blocks for
connection to street cabling e.g. detectors, lamp feeds etc.
Optionally, a transparent cover (667/1/21493/000) may be fitted to the
controller in front of the distribution panel; an aperture allows access to the
fuses and switches.
6.2.3 PCB Module
A modular PCB racking system is employed to accommodate the main
processor board with up to 4 Phase driver boards and additional facilities as
required.
6.2.4 Manual Panel & Cabinet Alarm
A manual panel is fitted behind a lockable door on the right hand side of the
case. Several versions of manual panel are available (see section 6.3.5). The
cabinet alarm indicator on this panel is visible to outside observation through
a red coloured lens in the Manual panel door.
667/HB/20200/000
Page 6-4
Issue 10
Type 400 Controller General Handbook
6.2.5 Uncommitted Space
The upper area of the cabinet is available for mounting ancillary equipment.
i.e.
Detector racks
OTU
OMU/OMCU
LMU
See the following table for possible combinations.
Table 6.2.5 Accommodation of Ancillary Equipment within a Large Outer-case
Total Capacity : 12U
Combination no.
Top of Cabinet
Bottom of Cabinet
Key:
1
3U
3U
3U
2
6U
3U
3U
3
5U
3U
3U
4
5U
6U
5
3U
6U
3U = 19” Detector Rack
5U = Siemens OTU/OMU, Ferranti OTU/OMU/MOVA, GEC OTU/OMU
6U = Siemens Controls Interrogator Unit
Notes:
a) These are typical combinations for general use - see drawing
667/GA/20287/000 for other combinations.
b) Although the controller can accommodate a large number of
detector racks, which implies a large number of detector cards, this
will be limited in practise by the available capacity of the power
supplies provided.
c) Special mounting brackets are available to support the Siemens
LMU.
667/HB/20200/000
Page 6-5
Issue 10
Type 400 Controller General Handbook
Figure 6.2(a) - T400 Large Outercase Front View (Typical)
OTU or OMU (if fitted)
Detector Rack (if fitted)
Logic Rask Assembly
(Made up of up to four
PCB modules)
Logic PSU
Fuse Rail
Dimming Transformer
667/HB/20200/000
Page 6-6
Issue 10
Type 400 Controller General Handbook
Figure 6.2(b) - T400 Large Outercase Rear View (Typical)
MANUAL
PANEL
ADDITIONAL TERMINATION PANEL
DD
BB
Z
X
T
R
N
EE
CC
AA
Y
W
S
P
MAINTENANCE
SOCKET
LOGIC
RACK
MASTER SWITCH
FUSES AND RCD
DISTRIBUTION PANEL
667/HB/20200/000
L
J
G
E
C
A
M
K
H
F
D
B
Page 6-7
ELECTRICITY
BOARD CUT-OUT
MOUNTING BLOCK
Issue 10
Type 400 Controller General Handbook
Figure 6.2(c) - T400 Large Outercase Front View (Hong Kong)
OTU or OMU (if fitted)
Detector Rack (if fitted)
Internal Manual Panel
Logic Rask Assembly
(Made up of up to four
PCB modules)
Logic PSU
Fuse Rail
Dimming Transformer
667/HB/20200/000
Page 6-8
Issue 10
Type 400 Controller General Handbook
Figure 6.2(d) - T400 Large Outercase Rear View (Hong Kong)
MANUAL
PANEL
SECOND PANEL (FITTED AS REQUIRED)
1
G
J
L
N
R
T
X
H
K
M
P
S
W
Y
12
1
12
MAINTENANCE
SOCKET
LOGIC RACK
MASTER SWITCH
FUSES AND RCD
FIRST PANEL (ALWAYS FITTED)
1
1
E
F
E
24
1
C
A
12
12
1
1
F
24
1
D
12
36
6
31
1
TBZ
ELECTRICITY
BOARD CUT-OUT
MOUNTING BLOCK
B
12
PED AUDIO
667/HB/20200/000
Page 6-9
Issue 10
Type 400 Controller General Handbook
6.3 EXPANDED DESCRIPTIONS OF T400 HARDWARE & OTHER EQUIPMENT
6.3.1 O.T.Us/O.M.Us
A number of different type OTUs and OMUs can be fitted into the T400
racking system. Their usual position being at the top of the controller.
The units which it is possible to fit are as follows:Siemens O.T.U
666/1/40700/etc
Siemens Scoot O.T.U
666/1/16600/etc
Siemens Short Rack O.T.U.
666/1/17000/etc
Siemens O.M.U
667/1/17500/etc
G.E.C Elliot O.T.U
Ferranti O.T.U
Ferranti O.M.U
O.T.U:- Out Station Transmission Unit links a controller to a central computer
to allow the co-ordination of traffic signals over a wide area.
Scoot O.T.U:- This is a Special Adaptation of the O.T.U which also sends
special loop detection information back to the central computer allowing the
computer to study traffic flow and optimise it.
O.M.U:- An Outstation Monitoring Unit again sends data to and receives data
from a central computer however, this unit monitors the controllers
performance and indicates any faults at the junction, which means faster and
more efficient maintenance.
6.3.2 TELECOMMAND 8 INTEGRAL SCOOT OTU (EXPORT ONLY)
This section has been deleted.
6.3.3 OTU Functions
The functions of the TC8 SCOOT OTU are as follow:
(1)
To demodulate the serial voice frequency data received from the
Instation Control.
(2)
To identify messages intended for the address or addresses for which
the OTU is set, otherwise take no action.
667/HB/20200/000
Page 6-10
Issue 10
Type 400 Controller General Handbook
(3)
To output the data content of Control messages in parallel form to the
traffic controller.
(4)
To input intersection and detector data.
(5)
To process this data (4 above) in the microprocessor.
(6)
To convert this processed data to serial form.
(7)
To convert the serial data to voice frequency signals and to transmit
these signals to the Instation in response to an appropriate Control
message.
(8)
Maximum number of OTU inputs and outputs are:24 inputs
16 outputs
6.3.4 Detector Racks and Detectors
A number of detectors and their associated racks can be fitted into the T400
racking system.
The units available are as follows:• Racks
19” Detector Rack (for T400 Large Controller) 667/1/20690/001
11” Detector Rack (for T400 Small Controller) 667/1/20690/000
Detector �L’ Bracket (for mounting 1 detector card) 667/1/17212/000
• Back-Plane
Double Back-Plane kit (for 2 detector cards) 667/1/15990/002
Single Back-Plane kit (for 1 detector card) 667/1/15990/003
• Detectors
Sarasota
- MTS 36Z - 2 channel unit 667/7/21031/002
- MTS 38Z - 4 channel unit 667/7/21031/004
Microsense loop Detectors Type MXED
667/HB/20200/000
Page 6-11
Issue 10
Type 400 Controller General Handbook
The following obsolete types may be utilised when replacing existing
controllers:Siemens (ST) Self Tune Detectors MkII
667/1/17180/012 = 2 detector channel unit
667/1/17180/014 = 4 detector channel unit
Microsense (ST) Self Tune Detectors Type MSE
667/7/20360/002 = 2 detector channel unit
667/7/20360/004 = 4 detector channel unit
*Sarasota MCE45Z
*
654/4/01023/000
Due to interference - these Sarasota cards must not be used
in the same rack that has any other type of detector cards
fitted.
6.3.5 Manual Panel & Cabinet Alarm
The T400 can be equipped with various Manual panels to support different
controller configurations and customer needs. These panels are detailed
below:(a) A full Intersection controller manual selection panel.
(b) A Police manual panel (step-on).
(c) An Internal Manual Panel.
(d) A Basic manual panel.
(e) Optional Pelican Controller Manual Panel
One of the above is fitted behind the small manual panel access door on the
side of the controller. When item (b) - Police manual panel - is fitted there is
an additional option to fit item (c) - the internal manual panel - inside the
controller. Access to the internal panel is via the main controller door.
The cabinet alarm LED is situated in the manual panel access door and lights
when the detector fault (DFM) system has detected an inoperative detector.
The LED is extinguished either by the DFM RESET push-button* (provided
the fault has been cleared) or when a defective detector is switched out of
use.
Note:- * Only if item (e) Optional Pelican Manual Panel fitted; on a standard
intersection or pelican controller the “RDF” handset command should
be used.
667/HB/20200/000
Page 6-12
Issue 10
Type 400 Controller General Handbook
6.3.5.1 Functions of the Intersection Controller Manual Selection Panel
The functions of the controls on the Intersection controller manual selection
panel are as follows:
Signals ON/OFF Switch
In the ON position allows the
microcomputer to control the signal
lamps supply. With OFF selected
switches off the signal lamps.
Mode selection pushbuttons
These buttons enable the selection of
Manual, VA, CLF, Fixed Time or
Normal modes of operation, provided
no higher priority mode is operative.
The VA, Fixed Time or CLF button may
be disabled if they are not required.
Mode Select Indicators
The indicator associated with the
button illuminates when the button has
been operated.
All Red selection
With the manual mode operative,
causes the controller to change to All
Red when selection is implemented.
Stage selection pushbuttons 1 to 7
These
pushbuttons
enable
the
selection of a user defined stage which
appears in each stream. It is important
to note that the number of the
pushbutton
selected
will
not
necessarily reflect the number of the
stage(s) that has been selected.
Stage Indicators
These indicators illuminate to indicate
the button which is associated with the
current stage.
Lamp Test
Applies a signal to the microcomputer
Pushbutton which illuminates all
indicators on the manual panel,
including the cabinet alarm lamp for
test purposes.
Awaiting Command Indicator
With manual mode operative (selected
on internal manual panel) lights when a
manual change is possible, i.e. the
associated minimum times have
expired.
Prohibited Move Indicator
With manual mode operative (i.e.
manual selected on internal manuals
panel) it lights indicating the attempted
manual stage change is prohibited and
will not be implemented.
667/HB/20200/000
Page 6-13
Issue 10
Type 400 Controller General Handbook
Hurry Call Indicator (AUX4)
Lights when the Hurry Call mode is
ACTIVE. Alternatively, this indicator
may be used for other special
purposes.
Higher Priority mode indicator
Lights (AUX5) when a mode with a
higher priority mode than manual mode
is active. Alternatively this indicator
may be used for other special
purposes.
SW1, SW2 and SW3 Indicators
Provide special facilities
Override, DFM Reset etc.
AUX1, AUX2 and AUX3 Indicators
These may be configured to perform
user defined functions.
e.g.
Dim
Figure 6.3.5.1 - Intersection Controller Manual Selection Panel
SIGNALS
CABINET
ALARM
OFF
ON
MANUAL CONTROL
BT TERMINAL
BOXES TYPE
14A & 35A CAN
BE FITTED HERE
BT LINE
JACK UNIT
1A CAN BE
FITTED
HERE
ALL
RED
1
2
NORMAL
3
4
5
MANUAL
6
7
AWAITING
COMMAND
FIXED
TIME
HURRY CALL
(AUX 4)
HIGHER PRIORITY
(AUX 5)
PROHIBITED
MOVE
AUX 1
AUX 2
AUX 3
SW 1
SW 2
SW 3
BT LINE JACK
UNIT 1A CAN
BE FITTED HERE
667/HB/20200/000
MODE SELECT
Page 6-14
VEHICLE
ACTUATED
CABLELESS
LINK
LAMP
TEST
BT TERMINAL
BOXES TYPE
14A & 35A CAN
BE FITTED HERE
Issue 10
Type 400 Controller General Handbook
6.3.5.2 Functions of the Police Manual Panel (Export Only, Hong Kong.)
The functions of the controls on the Police manual panel are as follows:
Signals ON/OFF Switch
In the ON position allows the microcomputer to
control the signal lamps supply. With OFF
selected, the signal lamps switch off.
Manual Control Enable
This pushbutton enables the operation of manual
step-on mode, provided no higher priority mode is
active.
Manual Control Disable
This pushbutton disables the operation of manual
step-on mode.
All Red Stage Selection
When operated with the manual step-on
Pushbutton mode operative the controller will
move to an all-red state, i.e. it will move to an all
red stage (or stages if parallel stage streams).
When coming out of all red the controller will go to
the next stage(s) in the sequence following the
stage(s) from which it went to all red.
Step-On Pushbutton
With the manual Step-on mode operative this
pushbutton causes the controller to move to the
next stage (or group of stages if parallel stage
streams are used) in cyclic order.
DFM LED
As stated at the beginning of this section this LED
illuminates when the controller detects a detector
failure. A red lens is fitted in the manual access
door to make the LED visible externally.
Active LED
This LED comes on when the manual step-on
mode has been enabled.
Manual disable switch
This is a microswitch which operates when the
manual panel door is closed, which if the controller
is left in manual step-on mode will return the
controller to normal operation.
Notes:-
The All Red push buttons on the Police manual panel and the
internal manual panel are wired in parallel. If running �internal’
Manual the Police Manual panel All Red button will have no
effect. If running �Police’ Manual the internal manual panel All
Red switch will also call the All Red stage.
A stage(s) may be configured such that while in manual step on
it will appear for a fixed period and then step on to the next
stage(s) without the step on button being pressed. If the disable
button is pressed the facility will be disabled. Similarly, if the
manual flap is closed, a magnetic switch operates to disable the
facility.
667/HB/20200/000
Page 6-15
Issue 10
Type 400 Controller General Handbook
Figure 6.3.5.2 - Police Manual Panel Layout (Hong Kong)
DOOR MICROSWITCH
CABINET
ALARM
SIGNALS
OFF
ON
PLESSEY
MANUAL
CONTROL
ACTIVE
667/HB/20200/000
ENABLE
ALL RED
DISABLE
STEP ON
Page 6-16
Issue 10
Type 400 Controller General Handbook
6.3.5.3 Internal Manual Panel (Export Only, Hong Kong)
Access to the internal manual panel is via the Controllers front door, see
Figure 6.3.5.3, and is usually limited to maintenance engineers. It allows a
limited control over the operation of the T400, as described below.
The functions of the controls and indicators on the internal manual panel are
as follows:
Mode selection pushbuttons
These buttons enable the selection of
Manual, VA, CLF, Fixed Time or Normal
modes of operation. The VA, Fixed Time
or CLF button may be disabled if they are
not required.
Mode Select Indicators
The indicator associated with the button
illuminates when the selection is
implemented.
Override Dim Pushbutton
Overrides lamp dimming requested by
solar cell or other means, i.e. timeswitch.
All Red Selection Push-Button
With the manual mode operative causes
the controller to change to all red when
selection is implemented. Note that this
button will also force All Red if Police
Manual is active.
Stage Selection Buttons 1 to 7
With the manual mode operative causes
the associated stage(s) to be selected
provided the request does not involve a
prohibited change.
Stage Indicators
These indicators illuminate to indicate
the button which is associated with the
current stage.
LAMP TEST Pushbutton
Applies a signal to the microcomputer to
illuminate all indicators on the manual
panel and lights the cabinet alarm lamp
for test purposes.
Signals Flash Pushbutton
Flashing AMBER/RED TO SELECTED
SIGNALS. This will be configured as
disabled.
AWAITING COMMAND Indicator
With manual mode operative (selected
on internal manual panel), lights when a
manual change is possible, i.e. the
associated minimum times have expired.
PROHIBITED MOVE Indicator
With manual mode operative (i.e. manual
selected on internal manuals panel) it
667/HB/20200/000
Page 6-17
Issue 10
Type 400 Controller General Handbook
lights indicating the attempted manual
stage change is prohibited and will not
be implemented.
HURRY CALL Indicator
Lights when the Hurry Call mode is
ACTIVE
HIGHER PRIORITY ACTIVE
Lights when a mode with a higher priority
than manual mode is active.
Spare LED Aux 3
This LED is a spare which may be
configured for a user-defined function.
Figure 6.3.5.3 - Internal Manual Panel Layout (Hong Kong)
HURRY CALL
(AUX 4)
OVERRIDE
DIM
6
AUX 3
ALL
RED
MANUAL CONTROL
HIGHER
PRIORITY
ACTIVE
(AUX 5)
SIGNALS
FLASH
3
7
PROHIBITED
MOVE
4
1
5
2
MANUAL
NORMAL
AWAITING
COMMAND
MODE SELECT
LAMP
TEST
667/HB/20200/000
CABLELESS
LINK
VEHICLE
ACTUATED
FIXED
TIME
Page 6-18
Issue 10
Type 400 Controller General Handbook
6.3.5.4 Basic Manual Panel
This is equipped with cabinet alarm lamp indicator and signals ON/OFF
switch.
Figure 6.3.5.4 - Basic Manual Panel Layout
CABINET
ALARM
SIGNALS
OFF
ON
667/HB/20200/000
Page 6-19
Issue 10
Type 400 Controller General Handbook
6.3.5.5 Optional Pelican Controller Manual Panel
This is equipped with all facilities as specified in MCE 0125 and MCE 0145.
Figure 6.3.5.5 - Pelican Controller Manual Panel
SIGNALS
CABINET
ALARM
OFF
ON
CONT PED
DEMAND
CONT
VEHICLE
EXTEND
VA
SELECT
FIXED
VEHICLE
PERIOD
667/HB/20200/000
AUX 1
AUX 2
AUX 3
SW 1
SW 2
SW 3
Page 6-20
DFM
RESET
LAMP
TEST
Issue 10
Type 400 Controller General Handbook
6.3.6 PCB Module
The PCBs are held within purpose built PCB modules. Figure 6.3.6 on the
following page shows how different combinations of boards are fitted into the
module. The small controller can be fitted with one or two PCB modules. The
large controller has space for up to four modules.
Figure 6.3.6 - Arrangement Of PCB’s Within Module
2 PCBs
Positions 1 & 3
2 PCBs
Positions 1 & 5
3 PCBs
Positions 1, 4 & 5
4 PCBs
Positions 1, 2, 4 & 5
PCB
Modules
Phase
Driver
Phase
Driver
Phase
Driver
CPU
Phase SDE/SA
Driver
or
Exp. IO
CPU
Exp. IO
SDE/SA CPU
or
Exp. IO
Example configuration with 8 to 16 phases
Exp. IO
SDE/SA CPU
or
Exp. IO
Example configuration for the TCSU 1995 contract
Exp. IO
CPU
(with config
change facility)
667/HB/20200/000
Page 6-21
IRM
SDE
RLM
Issue 10
Type 400 Controller General Handbook
6.3.7 Power System
Refer to drawing 667/DA/20200/etc.
The incoming mains supply is terminated at the Electricity Board cutout then
feeds to the Master Switch and fuse which isolates everything in the cabinet.
As an option a varistor can be fitted on the incoming line to protect the
controller against high voltage surges such as induced voltages produced by
nearby lightning strikes.
A fused supply feed is taken to the Maintenance Socket via an RCD. The
controller switch and fuse follow in series with the RCD, thus allowing the
mains supply to the controller to be removed whilst leaving power at the
maintenance socket.
The controller switch supplies the logic power unit and any additional
detector power unit. The lamp supply passes through a 20amp filter, solid
state relay, the dimming transformer, the dim/bright relay, the two signals
ON/OFF relays and finally the phase drivers.
The dimming transformer is an auto transformer with input tappings 200, 210,
220, 230, 240 & 250 volts a.c and output tappings 120, 140 & 160 volts a.c.
to lower to the mains voltage, to the signal lamps at night.
The solid state relay, through which the mains supply voltage to the dimming
transformer is taken, provides a noise free method of disconnecting the mains
supply from this circuit, whilst the necessary contactors are switched in or
out, during power up or a dim-bright change.
The logic supplies are derived from a switched mode power unit operated
from the mains supply. This unit has high stability and is very tolerant of
mains fluctuations. The power unit provides rail voltages of +5V, +12V, -12V
and +24v.
667/HB/20200/000
Page 6-22
Issue 10
Type 400 Controller General Handbook
6.3.8 LED Indicators
The functions of the various indicators on the logic rack boards are as
follows:• Main Processor
LED 1 -
System Error (Red)
- Illuminates when a fault condition is
registered in the controller Fault log.
LED 2 - Watchdog Fail (Red) - Illuminates when processor fails to
perform normal processing sequence.
LED 3 -
Power On (Green)
- Illuminates to show power supplies to the
card.
• Phase Drives
RED, AMBER and GREENs - Illuminate to indicate state of Phase.
6.3.9 Handsets
The majority of timing data held in the T400 is accessible and changeable
using one of the handsets described below plugged into the RS232 port on
the main Processor board.
667/7/13296/000
This is the black GR Electronics version with an
LCD (liquid crystal display) and a touch button
keyboard Approx. Size:- 78mm (3”) x 146mm (53/4”)
An Epson HX20 portable computer with software to
allow it to be used as an intelligent terminal. Note
that these are no longer available but are still
suitable for use where a customer has them.
A Portable IBM-compatible computer with suitable
software to act as an intelligent terminal.
6.3.10 300mA Controller Residual Current Detector
If required by the customer a 300mA RCD can be fitted to the controller. This
kit is added in areas of poor earths and is fitted in the controller mains input.
This facility is fitted as standard on the controller for the Tuen Mun - Yuen
Long LRT system contract.
667/HB/20200/000
Page 6-23
Issue 10
Type 400 Controller General Handbook
6.4 EXPANDED DESCRIPTIONS OF T400 PCBS
The following are descriptions of the facilities and functions found on each
PCB in the T400.
6.4.1 Main Processor P.C.B (667/1/20221/000)
The main processor board controls and monitors the functioning of traffic
controllers and pedestrian controllers. The processor is built around an
80188 (CMOS or NMOS) microprocessor, an enhanced version of the 8088
used in the Type 200 controller. This device incorporates the clock generator,
the interrupt controller, three timer/counters, various chip select outputs, and
a wait state generator, all housed in a 68 pin PLCC package.
The peripheral chip select signals generated by the 80C188 are used to
select the on-board peripheral devices. These peripherals are:- a RTC with
its own crystal and supported by the on-board battery during power down,
this provides all the time and date information required by the processor; a
phase driver interface capable of driving four phase driver boards, a total of
forty-eight outputs; local I/O interface with eight outputs and sixteen inputs, a
manual panel; the terminal port with RS232 output signal levels; a watchdog
timer facility; and the green/green conflict monitor.
The main processor board controls and monitors the many processes
required for correct operation of a T400 controller whether used as a traffic
controller or a pedestrian controller. The main processor board controls:
•
•
•
•
•
•
the lamp mains supply switching and dimming
the traffic signal phase drivers
four general purpose relay isolated outputs
serial data on the handset port
illumination of the LED’s on the manual panel
devices on the extended system bus
The main processor board monitors:
•
•
•
•
•
•
•
•
•
green/green conflicts both using software and dedicated hardware
the mains zero-crossing point
the phase driver lamp supply present outputs
the general daylight illumination to control lamp dimming
the manual panel switches
the handset port UART
the time and date using a dedicated RTC chip
sixteen general purpose inputs
the extended system bus for any peripheral board activity.
667/HB/20200/000
Page 6-24
Issue 10
Type 400 Controller General Handbook
Figure 6.4.1 - Main Processor PCB
10.0mm
LEVEL 3 ACCESS BUTTON
POWER ON LED (GREEN)
WATCHDOG FAIL LED (RED)
EXTENDED
SYSTEM BUS
(40 WAY IDC)
SYSTEM ERROR LED (RED)
E-H
A-D
TO MANUAL
PANEL
(34 WAY IDC)
TO PHASE
DRIVER BOARDS
(34 WAY IDC’S)
M-P
I-L
25 WAY
D-TYPE
HANDSET
SOCKET
16 INPUTS
(26 WAY IDC)
4 SIGNAL LAMP
RELAY OUTPUTS
AND
4 RELAY OUTPUTS
(16 WAY IDC)
POWER
(10 WAY)
10.0mm
FRONT
667/HB/20200/000
REAR
Page 6-25
Issue 10
Type 400 Controller General Handbook
6.4.2 4 Phase Driver PCB (667/1/20223/000)
The 4-Phase Driver Board acts as an interface between the Main Processor
Board and the Mains derived interfaces, all signals to and from the Main
Processor being electrically isolated from any Mains connections.
The Board is an extended 6U Eurocard with 2 Harting type connectors at the
rear (Mains interface) and an IDC Transition Header with 400mm Ribbon
Cable terminated with a 34 way IDC Socket at the front (Logic interface).
The earthed safety cover, on the component side of the Board, also acts as a
Heatsink for the Triacs.
The interface between the Main Processor Board and the Mains signals are
as follows:Twelve inputs from the Main Processor Board. These logic level signals
control the Mains supply to the Signal Lamps. i.e. Red, Amber and Green for
four Phases.
Eleven outputs from the Board, all to the Main Processor Board. These are:ZXO.
Lamp Supply Monitor.
Dim Request.
4 off +ve Green Monitors.
4 off -ve Green Monitors.
Electrical connections to the Processor Board are made via a 34 way IDC
connector. To ensure that, when more than one Phase Driver Board is fitted,
the IDC connectors are inserted only in the correct position on the Main
Processor Board, a Daisychain connection method is used.
6.4.3 2 Phase Driver PCB (667/1/20225/000)
The 2-Phase Driver Board with Red Lamp Monitor acts as an interface
between the Main Processor Board and the Mains derived interfaces, all
signals to and from the Main Processor being electrically isolated from any
Mains connections.
The Board is an extended 6U Eurocard with 2 Harting type connectors at the
rear (Mains interface) and an IDC Transition Header with 400mm Ribbon
Cable terminated with a 34 way IDC Socket at the front (Logic interface).
This Board is to be used with the T400 Pedestrian Controller since the
monitoring of the Vehicle Red Lamps of a Pedestrian Crossing is a
requirement in MCE0125 and MCE0145.
667/HB/20200/000
Page 6-26
Issue 10
Type 400 Controller General Handbook
The Vehicle Phase Red Signal Lamps are fed from the Vehicle Red Driver,
via Resistors. The potential difference across each Resistor is monitored to
ascertain the state of the Lamps.
The Audible Signal from the Driver is controlled by the Main Processor. The
voltage fed to the Audible Signal Driver is checked against a threshold and
the result is output to the Main Processor.
The Lamp Drivers, Green Voltage Detect, ZXO, and Dim Request Monitors
are identical to those used on the T400 4-Phase Driver Board
667/1/20223/000.
The earthed safety cover, on the component side of the Board, also acts as a
Heatsink for the Triacs.
The interface between the Main Processor Board and the Mains signals are
as follows:Seven inputs from the Main Processor Board. Six of these logic level signals
control the Mains supply to the Signal Lamps. i.e. Red, Amber and Green for
two Phases, and the seventh controls the Audible Signal.
Eleven outputs from the Board, all to the Main Processor Board. These are:ZXO.
Lamp Supply Monitor.
Dim Request.
2 off +ve Green Monitors.
2 off -ve Green Monitors.
4 off Red Lamp Monitor Outputs.
1 off Audible Signal Monitor. (Multiplexed with R L Monitor 1).
Electrical connections to the Processor Board are made via a 34 way IDC
connector. To ensure that, when more than one Phase Driver Board is fitted,
the IDC connectors are inserted only in the correct position on the Main
Processor Board, a Daisychain connection method is used.
6.4.4 Manual Panel P.C.B (667/1/20227/000)
The Manual Panel consists of a custom membrane type keyboard with LED
indicators and a toggle action style signals on/off switch.
The Manual Panel interface to the Main Processor Board is a 34-way IDC
plug.
The LEDs are driven via series resistors from driver ICs on the Main
Processor board. The switch matrix is scanned in rows and columns to save
on the number of connections.
667/HB/20200/000
Page 6-27
Issue 10
Type 400 Controller General Handbook
The membrane switches are all debounced in software to protect against
unintentional operation. Because of this, it is necessary to hold down a
desired key for about half a second to ensure recognition by the software.
6.4.5 Expansion I/O PCB (667/1/20229/000)
The Expansion I/O board provides the type 400 controller with an additional
sixteen buffered inputs, and sixteen relay isolated outputs. Up to three of
these boards may be used in a system so address decoding is provided to
identify each board by means of a BCD switch, and the setting of the switch is
visible on the front edge of the board, to guard against boards being set up
with the same address in a system.
The sixteen buffered inputs use comparators with protection against induced
voltages and direct application of mains voltages. The input to the buffer is
normally held high by a pull-up resistor.
The sixteen relay buffered outputs are clean contacts which are normally
open. Changeover relays are used to give some normally-closed outputs, and
provision is made for 22Ω contact protection resistors on some outputs in
addition to the normal 180Ω contact protection resistors.
On power up or Reset all the output relays go to the inactive state.
Sixteen buffered inputs and sixteen relay buffered outputs are available.
Each of these signal lines can isolate an inadvertent application of mains
voltage from the rest of the system even if it results in damage to the circuit
associated with that particular signal line.
The inputs are capable of meeting the requirements of MCE 0141, MCE
0125, and MCE 0145, and can reject induced mains voltages caused by
capacitive coupling between signal cables and adjacent mains cables.
There are sixteen relay isolated outputs, which are normally open with 180Ω
contact protection resistors. Four of these outputs are configurable; the
standard output is a normally open relay contact using a 180Ω contact
protection resistor, the two required alternatives are:- a) a normally closed
contact using a 180Ω contact protection resistor, and b) a normally open
contact able to switch higher currents than the standard output and with a
22Ω contact protection resistor.
The selection between the different output configurations is achieved by
using different pins in the output connector rather than any links on the
board. A standard cable is used with a Berg type socket with individually
crimped wires which select the standard normally open contact with the 180Ω
protection resistor. By moving the contacts in the header using the
appropriate tool the alternative output configurations can be provided.
667/HB/20200/000
Page 6-28
Issue 10
Type 400 Controller General Handbook
This board includes an identification byte which specifies this board as an
Expansion I/O board.
6.4.6 Expansion I/O PCB (667/1/20229/001)
The Expansion I/O board provides the type 400 controller with an additional
sixteen buffered inputs, and sixteen relay isolated outputs. Up to three of
these boards may be used in a system so address decoding is provided to
identify each board by means of a BCD switch, and the setting of the switch is
visible on the front edge of the board, to guard against boards being set up
with the same address in a system.
The sixteen buffered inputs use comparators with protection against induced
voltages and direct application of mains voltages. The input to the buffer is
normally held high by a pull-up resistor.
The sixteen relay buffered outputs are clean contacts which are normally
open. Changeover relays in two positions of each group of eight outputs give
the option of selecting some normally-closed outputs. 68Ω contact protection
resistors are used on all outputs.
On power up and whenever the RESET or Watchdog flag lines are active all
the output relays go to the output state.
Sixteen buffered inputs and sixteen relay buffered outputs are available.
Each of these signal lines can isolate an inadvertent application of mains
voltage from the rest of the system even if it results in damage to the circuit
associated with that particular signal line.
The inputs are capable of meeting the requirements of MCE 0141, MCE
0125, and MCE 0145, and can reject induced mains voltages caused by
capacitive coupling between signal cables and adjacent mains cables.
There are sixteen relay isolated outputs, which are normally open with 68Ω
contact protection resistors. Four of these outputs must be configurable; the
standard output is a normally open relay contact, the required alternative is a
normally closed contact.
The selection between the different output configurations is achieved by
using different pins in the output connector rather than any links on the
board. A standard cable is used with a Berg type socket with individually
crimped wires which select the standard normally open contact with the 68Ω
protection resistor. By moving the contacts in the header using the
appropriate tool the alternative output configuration can be provided.
This board includes an identification byte which specifies this board as an
Expansion I/O board.
667/HB/20200/000
Page 6-29
Issue 10
Type 400 Controller General Handbook
6.4.7 SDE/SA P.C.B (667/1/20231/000)
The SDE/SA processor card is built around an 80C85 microprocessor, a
CMOS version of the 8085 used on the T400 SDE/SA board. The design is
much the same as that used for the T400 although CMOS and HCMOS
components are used throughout to reduce the power consumption
substantially.
The maximum number of inputs is 32 which allows a maximum of 16
assessors since two loops are required per assessor. All of these inputs are
buffered. Unused SDE/SA assessors may be used as ordinary detector inputs
to the controller.
Communication with the main processor is achieved by the use of a Shared
RAM area which is located on the SDE/SA board. The main processor reads
and writes to this area via the Extended System Bus.
Power for the SDE/SA board is derived from the T400 main power supply.
The 5V DC supply comes on board via the Extended System Bus Cable while
the 24V DC supply is accessed via the detector input cable.
Soundmark type test facilities are provided by using an on board jack socket
and a thumbwheel switch to dial up any detector pair.
The board is able to run existing T400 SDE/SA software with a few slight
alterations reflecting hardware configuration changes.
667/HB/20200/000
Page 6-30
Issue 10
Type 400 Controller General Handbook
6.4.8 Ancillary Processor P.C.B (667/1/21611/000)
The Ancillary Processor is a double extended Euro sized PCB which
connects to the T400 Main Processor via the Extended System Bus.
Configuration information for the Ancillary Processor comes from the
Configuration PROM on the T400 Main Processor PCB. Handset access to
the Ancillary Processor is via the handset socket on the Main Processor
board.
6.4.8.1 Functional Applications
• Integral Red Lamp Monitor
• Integral TC12 OTU
• Integral Lamp Monitor
6.4.8.2 Physical Description
Mechanical Construction - The PCB is located within the T400 PCB Module,
along side the other T400 Logic PCB’s. It interfaces to the T400 Main
Processor PCB via the Extended System Bus ribbon cable, in a similar way to
the existing SDE/SA PCB.
Current Sensors & Voltage Monitor - There is a connector on the PCB to
allow connection of the current sensors and a voltage monitor which are used
for Red Lamp Monitoring and/or UTC lamp monitoring.
Telephone Line Interface (OTU) - There is a BT style Jack provided to allow 2
or 4 wire leased line connection, when used as an integral OTU.
Test Jack Sockets (OTU) - A Jack socket is provided to allow connection of a
TC12 Instation Test Set, for use in UTC systems. This permits monitoring of
line levels and communication data during installation and maintenance etc.
6.4.8.3 Ancillary Processor PCB Electronics
The Ancillary Processor PCB is based on the Intel 80188 microprocessor,
which is the same processor as used on the T400 Main Processor PCB.
The peripherals to the processor are the:
Firmware PROM
RAM (battery supported)
Shared RAM
A to D Converter with Analogue Multiplexer
Serial Interface (USART) with integral Modem and Line Interface
Watchdog Monitor Facility
Status LED Indicators
667/HB/20200/000
Page 6-31
Issue 10
Type 400 Controller General Handbook
Figure 6.4.8 - Ancillary Processor PCB
Status LED’s
PLA
40-Way
Extended
System Bus
Connector
LP2 - Carrier Detect
LP3 - Transmit Confirm
LP4 - Watchdog Fail
SK2 - Reply Line Jack Socket
SK3 - Control Line Jack Socket
ON
Push down this
side for �open’
switch (i.e. �0’)
Lithium Battery Switch - S2
S1 - 2/4 Wire Selector
S3 - Line Level Switch
Lithium Battery - B1
Serial No.
600Ω
S4 - 600Ω / High Impedance Selector
Hi-Z
Covered Area
SK1 - 6-Way Telecom Socket
Cover Fixings
667/HB/20200/000
Page 6-32
PLB
60-Way
Connector
to LMU
Inputs
Issue 10
Type 400 Controller General Handbook
7. GUIDE TO T400 SPECIFICATION FORMS
7.1 GENERAL
This guide is to assist Traffic Engineers in the completion of the Siemens
T400 Controller Specification Forms (667/DJ/15900), to enable Siemens to
submit quotations and supply traffic control equipment which provides the
desired performance. Where necessary refer to the facilities handbook
667/EB/20200 to assist in the understanding of the information to be given on
the forms.
The various pages of the forms are numbered in Roman numerals. Only
those forms required for a particular installation need to be completed, the
sheets are then numbered as required.
A set of blank specification forms is contained in Appendix A.
Some customers are able to configure their own controller EPROM’s. In order
to assist in the understanding of the configuration procedure, reference
should be made to the Intersection Configurator 003 user’s handbook
(667/HD/15900/000).
667/HB/20200/000
Page 7-1
Issue 10
Type 400 Controller General Handbook
7.2 LIST OF FORMS
FORM I
FORM II
FORM III
FORM IV
FORM V
FORM VI
FORM VII
FORM VIII
FORM IX
FORM X
FORM XI
FORM XII
FORM XIII
FORM XIV
FORM XV
FORM XVI
FORM XVII
FORM XVIII
FORM XIX
FORM XX
FORM XXI
FORM XXII
FORM XXIII
FORM XXIV
FORM XXV
FORM XXVI
667/HB/20200/000
FRONT SHEET
BASIC SITE DATA
USE OF PHASES
PHASE INTERGREENS
USE OF STAGES
PROHIBITED AND ALTERNATIVE MOVEMENTS
PROHIBITED AND ALTERNATIVE MOVEMENTS
DETECTOR AND PUSH BUTTON INPUTS
MODE PRIORITY AND DISABLED MODES
LIMIT VALUES
SPECIAL CONDITIONS FOR STAGE CHANGE
SDE/SA EQUIPMENT
URBAN TRAFFIC CONTROL
URBAN TRAFFIC CONTROL
MASTER TIME CLOCK AND CABLELESS LINKING
CABLELESS LINKING PLAN DATA
ADDITIONAL SWITCHES AND LEDs AND HURRY CALLS
LMU EXTEND INTERGREENS
EXTEND ALL RED
INDEPENDENT INTERGREENS
DEFINITIONS OF TIMESWITCH PARAMETERS
PEDESTRIAN LINK(S)
PRIORITY/EMERGENCY REQUIREMENTS
PRIORITY/EMERGENCY TIMINGS
NON-UK SIGNAL SEQUENCES
MANUAL STEP ON FACILITY
Page 7-2
Issue 10
Type 400 Controller General Handbook
7.3 FILLING OUT THE FORMS
Form I - Front Sheet
Every controller specification should begin with a �Front Sheet’ form.
This should be completed as far as possible, noting any standard
Regional or Local Authority Specification and quotation/order
numbers.
Form II - Basic Site Data
This form should show the basic phase movements for each stage. If
Parallel Stage streaming is used then the stream No, should be
indicated. One form could show 2 streams as long as they were kept
apart i.e. 1st stream using Top 4 boxes and 2nd stream using Bottom 4
boxes, but they would have to be clearly identified. Otherwise use 1
form per stream. The stages in the streams should be numbered
consecutively.
This form should also be used to indicate which stages correspond to
start-up and to All Red.
Form III - Use Of Phases
An entry should be made for each phase required (including
dummies).
(a)
Condition of Phase Appearance
There are 4 types (0 - 3) for the conditions for which a phase can
appear.
Type 0 - Phase always appears
The phase will always appear during its nominated stage(s).
This is the normal phase condition.
Type 1 - Phase appears only if demand exists at start of interstage
Under this type the phase will only appear if a demand exists for
it at the beginning of amber leaving of the previous stage.
Typical use simple parallel pedestrian phase dependent on
pushbutton.
Type 2 - Phase appears only if demand exists during the stage
or preceding inter-stage
Demand dependent phase which can appear at any time during
the stage if it is demanded. Typical use is filter green arrow.
667/HB/20200/000
Page 7-3
Issue 10
Type 400 Controller General Handbook
Type 3 - Phase appears if demanded at any time during the
stage up until the window time expires
The demand for a phase of this type can be inhibited by the
output of a special timer (�Window-Time’) which is started when
the first phase max time is started.
A typical use of this type is for a demand dependent pedestrian
phase which does not want to prolong the stage maximum when
an opposing demand has been requested.
(b)
Conditions of Phase Termination
The Type 400 Controller provides 3 types (0 - 2) for the termination of
a phase.
Type 0 Terminates at end of stage
This is the standard termination type - the phase showing
amber leaving, blackout, flashing green as required.
Type 1 - Terminates when associated phase gains Right of Way
This type is normally used for left turn filter arrows.
Type 2 - Terminates when associated phase loses Right of Way
This type is normally used for right turn indicative arrows.
(c)
Type of Phase
Enter a tick in the required column.
(d)
Conflicting Phase Combinations
Enter a �C’ for all conflicting phase combinations.
(e)
Phase Timings
Enter required timings.
667/HB/20200/000
Page 7-4
Issue 10
Type 400 Controller General Handbook
Form IV - Phase Intergreens
This form has four sections.
(a)
Basic Phase Intergreens
An intergreen time (in seconds) should be entered for every conflicting
phase.
(b)
Additional Phase Delays
This part of the form is used to detail any additional delay periods that
may be required for particular phases.
(c)
Starting Intergreen Period
This is the initial intergreen time period that is provided when the
controller is first switched on.
The time entered must not include the Amber period leaving time (3
secs) of the phases that show RED in STAGE 1.
667/HB/20200/000
Page 7-5
Issue 10
Type 400 Controller General Handbook
Form V - Use Of Stages
This form describes the basic stage structure of the controller and
comprises four sections.
(a)
Active Phases in each Stage
A �tick’ should be inserted in each box to define what the phase/stage
relationship is. Use a second Form if more than 7 stages are required
re-numbering the stages on the second sheet from 8 to 15.
The related stream number, and window time if required should be
indicated.
All dummy and demand dependent phases should be included.
The bottom line of this section (Max Revertive Demand Phase) should
be filled in if, a demand for a different phase is required if this Phase is
terminated with an extension timer active.
Note:- For parallel Stage Streaming each stream should have its own
all red stage, if the all red condition is required.
(b)
Fixed Cycle Time Requirements
A.
Define Fixed cycle time mode. Use additional sheets for each
stream. The fixed time cyclic order of stages should be defined
together with the stage time in seconds.
One
of
the
stages should be the Start-up stage.
OR
B.
Fixed cycle running to current Max. Tick the box for this mode
and tick any phase which is demand dependent. Note all other
phases will always appear and vehicle phases will run to max.
(c)
Arterial Reversion for each Stream
Insert the stage number(s) or Phase letter(s) if this facility is required.
(d)
Manual Selection
Complete this section if Manual Stage control is required by indicating
which stage(s) are to be associated with each button required. 8 pushbuttons are available, button 0 being allocated to All Red.
667/HB/20200/000
Page 7-6
Issue 10
Type 400 Controller General Handbook
Form VI/VII - Prohibited and Alternative Stage Movements
Use this form to describe the permissible stage to stage movements
for the various modes of operation.
For each mode of operation an appropriate movement table should be
completed or if modes movement tables are identical indicate which
modes each table applies to.
In CLF mode due care must be taken to ensure that controller does not
run stages for too long during plan changes particularly short filter
stages or pedestrian stages. Prohibited moves should not be
programmed. They should be changed to alternative moves. More than
one mode can apply to one sheet.
Form VIII - Detector and Push Button Inputs
After defining the detector location, ticks should be inserted in the
appropriate boxes to define the detector or push button requirements.
Phase letter to be inserted for the demand and extension.
Call/Cancel delay periods, LRT Request delay period, detector type,
supply voltage and Fault Monitor Time and fault monitor high limit
value should also be indicated.
Normal Detector inputs close the Relay Contacts and are treated as
�low’ inputs. If it is required to have Open Circuit Relay Contacts for
detection then a tick should be placed in the “Inverted” column on this
form. U/D refers to uni-directional detectors that will detect vehicles
moving in one direction only. The Call Delay Column refers to
Call/Cancel Units used for vehicles.
667/HB/20200/000
Page 7-7
Issue 10
Type 400 Controller General Handbook
Form IX - Mode Priority and Disabled Modes
This form comprises two sections:
(a)
Mode Priority
The modes under which the controller shall operate need to be
defined in this section. Each mode required, should be given a
number from 1 to 9 (1 is top priority) or an �X’ if it is not required.
Particular attention should be paid to the priority of any Manual
facilities with regard to Cableless Link operation, such that CLF
does not disable Manual. Note CLF should always be requested
so that CLF could be added by the Handset.
The capabilities of the Manual facility switch, located on the
internal Manual panel, should be defined in the bottom boxes if
any of the modes defined are not required to be selectable.
Box 2 should define if Manual only allowed if:(i)
Handset is inserted.
(ii)
MND is entered on the Handset
Note:- a priority state should be entered for either Vehicle
Actuated (VA) or Fixed Time (FT) not both.
(b)
Disabled modes
This section of the form allows modes which have been
selected to be disabled for certain streams or for all streams for
certain conditions. e.g. CLF on one stream allows other streams
to still work VA. Also Manual control could be disabled at certain
times of day. Note that Part Time and Selected Manual Control
modes may only be disabled on all streams simultaneously.
667/HB/20200/000
Page 7-8
Issue 10
Type 400 Controller General Handbook
Form X - Limit Values
This form details the upper and lower limits for certain timings which
limit any handset changes to these timings, see section 2.6 for details.
The defaults for all of these range limits are shown on the forms in
Appendix A. These can be changed if necessary within the ranges
given below :(a)
Phase Intergreen
Low Value
High Value
2 secs for traffic phases
(red/amber time)
0 secs for ped. and
Green Arrow phases
199 secs
(b)
Minimum Green Times
Low Value
High Value
0 secs
255 secs
(c)
Phase Delay
(d)
Starting Intergreen
Low Value
High Value
Low Value
0 secs
255 secs
0 secs
High Value
255 secs
(e)
CLF Group Time
Low Value
High Value
0 secs
255 secs
(f)
Maximum Green
Low Value
High Value
0 secs
255 secs
(g)
Pedestrian Blackout/
Flashing Green
Low Value
High Value
0 secs
255 secs
(h)
Green Extension
Low Value
High Value
0 secs
10.0 secs
(i)
CLF Offset Time
Low Value
High Value
0 secs
255 secs
(j)
Priority 1st Delay
Low Value
High Value
0 secs
255 secs
(k)
Priority 2nd Delay
Low Value
High Value
0 secs
255 secs
(l)
DFM
High Value
254 hrs
667/HB/20200/000
Page 7-9
Issue 10
Type 400 Controller General Handbook
Form XI - Special Conditions For Stage Change/Extra Requirements
Some Stage to Stage movements may require special conditioning.
This form should be used to describe the various input states and
phase status that are required for the special condition to be satisfied.
The form is also used to list any special extra requirements that have
not been specified anywhere else, (e.g. requirements for linking to
another controller, Part-Time mode should be configured for Flashing
Amber, Parallel Stage Stream influence and cross linking etc). Usually
these extra requirements will be ones that require special conditioning.
Further sheets should be added for different modes, but if special
conditions are identical in certain modes, then these should be listed
on the same form.
Form XII - Speed Discrimination/Speed Assessment Equipment (SDE/SA)
This form need only be completed if the controller is to be used on an
intersection having high-speed vehicles.
The equipment type (SDE or SA) should be specified together with the
number of assessors and their function.
If SDE is selected only assessor types 1, 2 or 3 are available.
If SA is selected all assessors must be type 4.
An Extra-Intergreen period should be specified for every phase that is
equipped with an assessor. Following MCK 1057 amendment it is
normal for only high speed extensions to provide extra I/G. The right
hand box would normally be ticked to prevent X, Y, Z detector
extensions from providing extra clearance.
Note there is an option to use 12 foot loop spacing if required.
667/HB/20200/000
Page 7-10
Issue 10
Type 400 Controller General Handbook
Form XIII - Urban Traffic Control
The top left table to be filled in with any control and reply bits that
communicate via an OTU. Note any bits to an associated controller
should have a �*’ by the bit.
Where force bits are required to be demand dependent add a # (hash)
and fill out the bottom right hand table with the phase demands which
are to be considered as requests for that force. This includes both
demands originating from the street or from D bits. If there is no hash
each force bit will act irrespective of any demands.
Demand bits (Dx, D1, D2 etc.) are numbered from 1 upwards and the
tables on the right determine their function. The top table determines
which phases, or stages, or combinations will be demanded by each
bit. Dx is made larger as up to 16 stages and or 16 phases could be
required.
Similarly in the second table on the right hand side, insert which
phases should be extended by each �D’ bit.
In the third table on the right hand side fill in the stage demands which
will cause a reply. (A reply will occur if that stage has a demand).
Alternatively specify the phase demands which are required to reply.
NOTE:TO AVOID CONFUSION IT IS ESSENTIAL THAT CONTROL AND
REPLY BITS ONLY USE THE NOTATIONS ON THIS SHEET.
Form XIV - Urban Traffic Control
Tick any square which requires the reply bits along the top to be active
during the conditions on the left hand side. If the �other’ column is
used, detail which reply bit this information should be sent on.
The controller fault bit is set if an entry is made in any Fault Log Flag
except for the flags associated with DFM failure, Priority DFM failure
and Lamp Supply failure. For a complete list of Fault Log Flags, refer
to the Handset Handbook 667/HH/20200/000.
667/HB/20200/000
Page 7-11
Issue 10
Type 400 Controller General Handbook
Form XV - Master Time Clock and Cableless Linking
This form need only be completed if time-switch and/or Cableless link
facilities are required.
First select the �Day Type’ (0 - 9) from the list provided, then enter the
time that the function is required to operate (use 24 hour clock
notation).
Last of all define the function that has to be performed, along with a
description of it.
Add extra sheets as required up to a total of 64 entries.
Form XVI - Cableless Linking Plan Data
This form need only be completed if Cableless linking is required.
For the left hand table indicate the Plan number and influence set
used, then allocate a Group time (in seconds) for each group used, (0
seconds if you want it to be skipped, a time may be added using the
handset at a later date, see Appendix A).
For the right hand table indicate the influence set number, and then
allocate a Group Influence and Related Stage for each group required.
One Influence set may be used for more than one plan.
Note:- With parallel stage streaming indicate Group Influence and
Related stage for each stream required, otherwise just for Stream 0.
NOTE FOR INFLUENCE 0, 3 AND 7 A STAGE IN THAT STREAM
MUST BE ENTERED.
Add extra sheets as required for up to 8 plans.
667/HB/20200/000
Page 7-12
Issue 10
Type 400 Controller General Handbook
Form XVII - Additional switches and LEDs and Hurry Calls
This form comprises four parts :(a) Additional Switches and LEDs
There are three spare switches and three spare LEDs on the
Manual Panel. This form is used to specify if a function is to be
allocated to the switch or LED. The switches and LEDs may all
be used independently, but if a toggle action is specified then
the associated LED will operate in conjunction with the switch,
i.e. press once to turn the switch on and the associated LED
illuminates to indicate that the switch is on, press again and the
LED will go off to indicate that the switch is off.
The default action of the switch is that of a toggle switch. If it is
required to use the switch as a momentary switch then a tick
should be placed in the “momentary” column against the
particular switch. When used as a momentary, the switch will be
on while the switch is pressed.
If the switch is specified as Momentary or the switch is not used,
then the associated LED may be used independently for any
purpose.
Describe the functions required for the switches and LEDs in
the “Use” column.
(b) Hurry Call(s)
All information relating to any Hurry Calls should be specified in
this table.
(c) Optional Filter green arrow in Manual
This section should be used to indicate whether the Filter green
arrow(s) should appear, not appear or be demand dependent
during Manual mode.
(d) Part Time Mode
If this mode is required then the switch off stage should be
specified here.
Where parallel stage Streaming is used enter one stage for
each stream.
Any special part time requirements should be detailed on Form
XI.
667/HB/20200/000
Page 7-13
Issue 10
Type 400 Controller General Handbook
Form XVIII - Red Lamp Monitor
This form is used where Red lamp monitoring is used as defined in
MCK 1061. Note that if the new enhanced red lamp monitor system is
required, the original �extend intergreen’ page should be ignored.
Form XIX - Extend All Red by Detectors
If All-Red Extension facilities are required this form should be
completed by indicating the Extend All Red Moves for each unit
required, the effect of this facility in certain modes and the All Red
extension time (per stream required).
Note:- The All Red Maximum time is measured from the point at which
the first phase in the new stage would normally start its Red to
Green transition period (usually Red Amber).
The extension time is measured from the point at which the loop
becomes unoccupied.
Form XX - Independent Intergreens
Fill in any phases which are not to be held by the intergreen of a
terminating phase.
Form XXI - Definition of Time Switch Parameters
This form is used in conjunction with form where a time switch is
specified as function 2, (introduce an event time table).
Each line of this form represents a switch, (0-15). Facilities are
allocated to these switches, as required.
The parameters, (0-15) can then be filled out with any combination of
the switches, as required. e.g. select Max set B.
If this sheet is filled in, it should be included immediately following form
XV.
667/HB/20200/000
Page 7-14
Issue 10
Type 400 Controller General Handbook
Form XXII - Pedestrian Link
This form need only be completed if linking to an adjacent
Pedestrian/Pelican controller is required.
Form XXIII/XXIV - Priority/Emergency Mode
This form need only be completed if LRT and/or Emergency vehicle
priority facilities are required.
(a) Basic Requirements
For each priority unit required its type, related phase and
monitoring/gap timings should be specified.
The configured conditioning of �Priority Demand’, �Revertive
Priority Demands’, �Inhibit Times’ and �Priority DFM Self - Reset’
should also be stated.
Note:Some �Enabled’ states are conditional on other facilities also
being enabled.
The number(s) corresponding to the priority unit(s), which are
required to be inhibited, should be entered into the next box.
The next section should specify which demanded phase(s) will
be serviced when a move to the priority phase takes place, (if
any).
The last section specifies which phase(s) will be demanded
when a move to the priority phase takes place, (if any).
Note:Phase(s) specified in “ENFORCE DEMAND” must also appear
in �ALLOWED VA DEMANDS’.
(b) Time Periods
The timings for each priority unit should be specified on this
form and the plan type indicated in the section provided.
667/HB/20200/000
Page 7-15
Issue 10
Type 400 Controller General Handbook
Form XXV - Non-UK Signal Sequences
This form is only applicable to some export requirements. If the signal
sequences as shown in the table are required, then a tick should be
placed in the box at the top of the page.
It is possible to specify two methods of operation for the Signals on/off
switch. In both cases, when the signals are switched off, the controller
continues cycling as normal, except that the signals are no longer
illuminated. If a tick is placed in the box against “Immediate Signals
On”, then when the Signals on/off switch is set back to the “on”
position, the signals immediately illuminate at whatever point they
were, in the controller cycle. If a tick is placed in the box “As Startup”
then the controller will go through the startup sequence to illuminate
the signals.
If the signal sequence specified includes flashing e.g. flashing green in
the pedestrian sequence, then unless otherwise specified the flashing
on and off times will both be 400ms. If it is required to have different on
or off times, then the required value(s) should be entered in the boxes
provided on this form.
Form XXVI - Manual Step-On Facility
This is an alternative to full UK Manual mode operation, where instead
of having a different button to select each stage (or pattern of stages in
Parallel Stage Streaming), one button makes the controller step
through a predefined pattern of stages.
In the boxes to the side of “Stream 0”, enter the stage numbers in
sequence from left to right, to specify the order in which the stages
should appear. If there is more than one stream, repeat this process
for the other streams. Stages that appear in the same columns of the
form will run together. The same stage may be specified more than
once within the Manual cycle if required. This may occur by either
double appearance or the same stage in one stream running with two
separate stages in another stream.
Movement from one stage to the next, or in the case of parallel stage
streaming from one pattern of stages to the next, occurs in one of two
ways. The first way is by operation of the Manual Step On button. In
this case a tick should be placed in the box at the bottom of the column
indicating that the Manual Step On button must be operated in order
that the controller moves from the stage pattern specified. The second
way is to move automatically after the time as defined in the box
(instead of entering a tick) onto the next stage, or pattern of stages.
667/HB/20200/000
Page 7-16
Issue 10
Type 400 Controller General Handbook
8. T400 MOD STATE CONTROL AND CONFIGURATION
All these details are contained in the document 667/SU/20200/000.
A copy of this document is contained in Appendix B.
667/HB/20200/000
Page 8-1
Issue 10
Type 400 Controller General Handbook
Appendix A - SPECIFICATION SHEETS
Appendix A contains a copy of document 667/DJ/15900/000 follows:-
667/HB/20200/000
Page 1
Issue 10
Type 400 Controller General Handbook
Appendix B - MOD STATE CONTROL AND CONFIGURATION
Appendix B contains a copy of document 667/SU/20200/000 follows:-
667/HB/20200/000
Page Error! Main Document Only.-1
Issue 10
Type 400 Controller General Handbook
Appendix C - 50-0-50 VOLT CONTROLLER
C.1 50-0-50 VOLT CONTROLLER
Note :- This version of the T400 does not meet DTp specification MCE0141
in respect of dimming voltages and voltage sensing. This is inherent
in the 50-0-50 volt output. The 50-0-50 version of the controller does
meet the equivalent figures which are specified by (50+50)/240.
The 50-0-50 volt controller is a version of the standard so that the voltages
on the cables leaving the controller are 50 volts A.C. nominal with respect to
earth, rather than the standard 240 volts and are transformer isolated from
the incoming mains supply.
The voltages on feeds an auxiliary devices such as regulatory signs,
microwave detectors, solar cells etc. is nominally 50-0-50 volt rms with the
centre tap taken to earth. Low voltage dc supplies for detectors (nominal 24
volts) are unaffected.
An additional circuit breaker is provided to enable the 50-0-50 volt feeds to
be isolated with a single switch without switching the controller logic off. This
also provides protection if either of the 50 volt feeds is shorted to earth. (This
does not include the 24 volts intended for supplying external loop detectors.)
C.1.1 Signal load limitations
The current supplied to the controller is limited compared to the standard 240
volt T400 controllers detailed below. Figures assume 0.614A per lamp.
For a large outercase controller fitted with a 1.5 kVA dimming transformer.
Maximum load per individual phase
Maximum load per phase board
Total lamp O/P load per controller
-
4 amps (6 lamps on at one time*)
10 amps (18 lamps on at one time)
15 amps (25 lamps on at one time)
For a small outercase controller fitted with a 1.0 kVA dimming transformer.
Maximum load per individual phase
Maximum load per phase board
Total lamp O/P load per controller
-
4 amps (6 lamps on at one time)
10 amps (18 lamps on at one time)
10 amps (18 lamps on at one time)
Note that the regulatory sign load, solar cell load and any other low voltage
ac loads such as pedestrian audio, wait box, etc, all form part of the controller
load.
*
These figures assume each lamp transformer (on load) takes 0.614 Amps (worst case).
667/HB/20200/000
Page C.-1
Issue 10
Type 400 Controller General Handbook
C.1.2 Miniature Circuit Breaker (MCB)
A miniature circuit breaker is used to provide overload protection on the lamp
supply outputs. It also protects the outputs to the regulatory signs, MVDs,
Solar cells etc. The MCB acts as a switch enabling the maintenance to be
carried out on the signals heads etc without stopping the controller logic.
Note : When the signals are switched off using the MCB, controller fault log
17 (Lamp supply fail detected) will be set. This should be reset using
handset command RFL=1 when the MCB is returned to the normal
position.
C.1.3 Street Equipment
C.1.3.1 Solar Cell
A 110 Volt version of the solar cell, derived from the 50-0-50 volt
supply, via a transformer mounted in the adjacent signal head.
C.1.3.2 High Intensity Signals
All signals and pedestrian wait boxes must be modified using
transformers designed for 50-0-50 supply. The H.I. have tapped
secondaries to compensate for the increased voltage drop that is
caused by operating at a lower voltage and higher current. Two taps
are available selected on the basis of cable length :- 0 to 60 metres and
61 to 120 metres for distances greater than this 2 cores should be used
for each feed. Note a separate return should be used for each head or
wait indicator with a separate feed per optic..
C.1.3.3 Regulatory Signs
A modification to standard regulatory signs is required, incorporating an
auto transformer to step he 50-0-50 up to 110 volts for the fluorescent
tube circuits.
C.1.3.4 Microwave Vehicle Detectors
The microwave vehicle detectors must be the type 110 volt version
which allows operation on the 50-0-50 volt supply using the regulatory
supply.
C.1.4 Dual Solar Cell
The solar cell facility on a 50-0-50 controller can be modified to enable two
solar cell outputs to be provided. These are connected to the controller via
667/HB/20200/000
Page C.-2
Issue 10
Type 400 Controller General Handbook
two relays mounted within the controller. One of the solar cells acts as a
�master’ causing the controller to change from �dim’ to �bright’ and �bright’ to
�dim’ in the normal manner. This facility is not available on a 240 volt
controller.
The two solar cells are then monitored and when of the following two fault
conditions occur the signals will be set to the �bright’ state.
1.
If both solar cells outputs are in different states for more than 16 hours.
This is adjustable with the range of 0 to 255 hours using handset
command PIR0. The value which is assigned to handset command
PIR0 will give required monitor time in hours, with the default setting
being 16.
2.
If the solar cell outputs are in different states for more than 45 minutes.
This is adjustable with the range of 0 to 255 minutes using handset
command PIR1. The value which is assigned to handset command
PIR1 will give required monitor time in minutes, with the default setting
being 45.
When either of the above two faults occur the controller fault log 27 will be
set as shown below. The fault log will remain set until reset using the
handset. While the fault log is active the signals will be held in the nondimmed state.
FLF 27 = 1
If the solar cell outputs remain in the same state for more than
16 hours.
FLF 27 = 2
If the solar cell outputs are in different states for more than 45
minutes.
FLF 27 = 3
If both the above conditions occur.
C.2 GAS PLINTH
A gas plinth can be fitted below the controller to inhibit any gases from
entering the controller, the gas is allowed to escape via the vented plinth. All
cables entering the controller must pass through the gas plinth with cable
glands being used to seal the cables. There are a maximum number of cables
that can enter the controller when a gas plinth is used, as detailed below :Small case controller
Large case controller
667/HB/20200/000
-
18 cables (Including electrical supply)
27 cables (Including electrical supply)
Page C.-3
Issue 10
Type 400 Controller General Handbook
Appendix D - ADDITIONAL REQUIREMENTS FOR TUEN MUN
D.1 LAMP DRIVE CAPABILITY
Maximum lamp load for total controller
(including regulatory signs and red/amber)
Maximum lamp load for one phase switch
card (4 phases, including red/amber)
This is limited by the fuse on the PCB
Maximum load for one triac output on a phase
switch card
Amps
Tungsten
Halogen
Lamps
Total
Watts
20A
63
4000
10A
19
1200
4A
12
800
N.B. The Lamp and Wattage columns are equivalents for the currents
shown, based on a 200 volts supply. Power Factor greater than 0.9
D.1.1 Lamp Load Per Aspect (Watts)
Bright
Tungsten filament
40 watt Wait Indicator
50 watt High Intensity
Regulatory sign
6
42
63
63
Dim
160v
57
32
43
-
Dim
140v
38
-
Dim
120v
47
22
32
-
D.1.2 Dimming Transformer
Transformer
120v
140v
160v
120v
140v
160v
120v
140v
160v
1kVA
1.5kVA
2kVA
Notes:-
Transformer
Tap
Maximum number of
lamps on a controller
continuously
illuminated
31
28
27
46
41
37
62
55
51
Maximum number of
lamps illuminated for
a short time#,
e.g. Red/Amber
63
63
63
63
63
63
63
63
63
# = Limited by controller lamp supply fuses F5 & F6 which can be
a maximum of 20 amps. These figures are based on a 200 volt
RMS supply. All figures are for tungsten halogen lamps.
667/HB/20200/000
Page D.-1
Issue 10
Type 400 Controller General Handbook
D.1.3 Calculation Of An Intersections Power Requirements
The following worked example is based upon a mains supply of 200 volts
rms.
Firstly the average lamp power for the junction is calculated, this allows the
selection of the dimming transformer. Secondly the average lamp power is
added to the average controller power to give the total average power which
a local authority may use to estimate running costs.
Average lamp power is calculated as follows:For every signal head, 1 lamp is illuminated at 63 watts, every wait indicator
is illuminated at 42 watts, every regulatory sign is illuminated at 63 watts.
Therefore considering our theoretical junction Figure 2.2 we have the
following result.
a)
b)
c)
1 lamp per signal head at 63 watts
Every wait indicator illuminated at 42 watts
Every regulatory sign illuminated at 63 watts
63 x 12
42 x 4
63 x 1
=
=
=
756W
168W
63W
987W
To select the dimming transformer first select the tapping and then choose
appropriate power rating from following table.
Dimming Voltage
120v
140v
160v
667/HB/20200/000
Power load watts at full voltage
load < 1969
1969 < load < 2898
2898 < load < 3906
load < 1764
1764 < load < 2583
2583 < load < 3465
load < 1700
1700 < load < 2331
2331 < load < 3213
Page D.-2
Dimming transformer
1.0K VA
1.5K VA
2.0K VA
1.0K VA
1.5K VA
2.0K VA
1.0K VA
1.5K VA
2.0K VA
Issue 10
Type 400 Controller General Handbook
The average controller power is calculated as follows:A controller with dimming is 105 watts plus the number of detectors required
at 6 watts/board for every Siemens ST detector.
Therefore, for our theoretical junction Figure 2.2 the result is as follows:1 x Controller
1 x Siemens ST detector
105 watts
6 watts
111 watts
For the total average power to aid electricity authorities with the running cost
estimates, the lamp average power must be added to the controller average
power.
e.g.
+
987 watts
111 watts
1098 watts
D.1.4 Calculating The Lamp Supply Fuse Required
In order to calculate the lamp supply fuse required the worst case red/amber
is used, i.e. the red/amber during which the most signal heads are at
red/amber. For the theoretical junction Figure 2.2 this is during the move 2 to
1 with 5 signal heads at red/amber.
Signal heads at red/amber x 126 watts
Signal head with 1 lamp illuminated x 63 watts
Every wait indicator illuminated x 42 watts
Every regulatory sign illuminated x 63 watts
5 x 126
7 x 63
4 x 42
1 x 63
=
=
=
=
630W
441W
168W
63W
1302W
The lamp power is then re-calculated using 126 watts for every signal head at
red/amber. This gives us the peak lamp power, e.g. for our theoretical
junction Figure 2.2.
This is divided by 200 volts to give us the peak lamp current, e.g. 1302 Г· 200
= 6.5 Amps.
Then from the following table we derive our fuses:
Peak Lamp Current
0.0A < Current < 6.5A
6.5A < Current < 9.5A
9.5A < Current < 14A
14A < Current < 19A
667/HB/20200/000
Page D.-3
Fuse
7A
10A
15A
20A
Issue 10
Type 400 Controller General Handbook
D.2 HANDSET RANGE LIMITS, DEFAULT VALUES
Unless otherwise stated all controllers will be provided with default timings for
the limits as shown below:TUEN MUN
a)
D.F.M.
b)
Hurry Call Delay
Hurry Call Hold
Hurry Call Prevent
c)
Phase Delay
d)
Starting Intergreen
e)
Green Extension
f)
Maximum Green
g)
h)
Pedestrian Blackout/
Flashing Green
C.L.F. Group Time
i)
Minimum Green Times
j)
Phase Intergreen Time
k)
CLF Offset
l)
Priority First Delay
m)
Priority Second Delay
667/HB/20200/000
High Value
Low Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Low Value
High Value
Page D.-4
24 hrs
0 hrs
0 secs
180 secs
5 secs
180 secs
0 secs
120 secs
0 secs
20 secs
3 secs
20 secs
0 secs
5 secs
0 secs
100 secs
3 secs
20 secs
0 secs
120 secs
5 secs
20 secs
5 secs
20 secs
0m0s
0 m 120 s
0 secs
120 secs
0 secs
120 secs
Issue 10
Type 400 Controller General Handbook
D.3 INPUTS AND OUTPUTS
The following I/O allocation will be given to all controllers:
Port 4
Port 4
Port 7
Port 1
Port 2
Port 3
Port 6
Port 6
Port 6
667/HB/20200/000
Bit 0
Bit 7
All Bits
All Bits
All Bits
All Bits
Bit 0
Bit 1
Bit 7
T400 Fault
Pedestrian audibles ON/OFF control
LRV requests
Road detectors
Pedestrian pushbutton inputs with DFM
Pedestrian pushbutton inputs without DFM
Interrogator fault 1
Interrogator fault 2
Audibles permanent/timed
Page D.-5
Issue 10
Type 400 Controller General Handbook
D.4 ADDITIONAL INFORMATION FOR TUEN MUN SPECIAL SPEC. SHEETS
Forms TMLRT1 & TMLRT2 - Controller inputs
These forms to be used instead of standard Siemens form VIII.
Form TMLRT3 Switching details for DIMMING, AUDIBLES & PED DFM
This form is used to specify the times of day that the following facilities are
required; Audibles ON, Audibles OFF, Switch to BRIGHT, Switch to DIM,
Pedestrian pushbutton DFM ON (active) and Pedestrian pushbutton DFM
OFF (inactive).
Form TMLRT4 LRT Interface Connections - High Voltage
This form is used to indicate the high voltage signals passing through the
LRT Interface Unit. These signals will be the Mains voltages to drive the LRT
Signals aspects. The T200 terminals that they originate from should be left
for Siemens to complete, but the terminals that they are going to should be
indicated. (e.g. Post 1, Phase A).
Note:- If the partial interface unit is being used then the second terminal block
TBE is not fitted.
Form TMLRT5 LRT Interface Connections - Low Voltage
This form is used to indicate the low voltage signals passing
through the LRT Interface Unit. TBA2 to 11 should be used for LRT Request
and Fault Signals, indicating the terminals that they originate from. The T200
terminals that they are going to should be left for Siemens to Complete.
TBA/12 to 13 are for T200 fault Signals. The terminal that they are going to
should be indicated, (e.g. Interrogator/Decoder TB1).
TBB is used for the returns to the above mentioned signals.
Note:- If the partial interface unit is being used then there are a reduced
number of request signals.
Form TMLRT6 Record of Amendments
This form is to be filled in with the issue, a description of the changes (if not
initial issue) the date and initials of author. This helps with the traceability of
changes.
667/HB/20200/000
Page D.-6
Issue 10
Type 400 Controller General Handbook
Form TMLRT7 Special Conditioning LRT Fault Conditions
This form is used to specify what actions are to be taken when a specific LRT
fault occurs and under which mode it is applicable.
Fault conditions:- Artificial requests being received, Priority DFM timed out,
Interrogator fault present.
Actions:- Insert maximum extend all red, Use specified max set, Insert
permanent demand and/or extension for a phase, Inhibit prevents.
667/HB/20200/000
Page D.-7
Issue 10
Type 400 Controller General Handbook
Appendix E - T400 Controller drawings
Appendix E contains a copy of those T400 drawings which are referred to
throughout this document.
667/HB/20200/000
Page E.-1
Issue 10

Release Notes RobotStudio - ABB Download Center

Panasonic KX-TW501/ Panasonic KX-TW502

(ACME) LED-767RGBW II USER MANUAL - 06.17.2014

Configuration Manual KH 6495-2 EN

Slim Jim thin profile LED sign - Lasermet, Ltd

Guillotine pdf free - PDF eBooks Free | Page 1

DMC-40x0 User Manual - SONG

Harvest pdf free - PDF eBooks Free | Page 1

KUBOTA HORIZONTAL - Diesel Pump

15MV2722E_Program Brochure_14MV7777

Commodity Research Desk

#09 - A how-to guide for Trial Summary 3.1.3x - PhUSE Wiki

to - Department of Education (S)

PROGRAMME - CORYS

AA-7000 Series - Shimadzu

2015 Rivers - University of Rhode Island

Newsletter – March 2015 - expat

Visit our website at okanaganmarathon.ca

Weekly Announcements - Saint Paul`s Lutheran Church

to view the proposal. - Riverhead Free Library

Forward-Looking Statements

MONDAY, 3/30/2015 PURCHASE ANY SIZE COFFEE & GET A